| /linux-4.4.14/Documentation/devicetree/bindings/media/ |
| D | renesas,vsp1.txt | 22 - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is
24 - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is
26 - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU)
|
| /linux-4.4.14/Documentation/devicetree/bindings/input/ |
| D | gpio-keys.txt | 7 - autorepeat: Boolean, Enable auto repeat feature of Linux input
26 - wakeup-source: Boolean, button can wake-up the system.
28 - linux,can-disable: Boolean, indicates that button is connected
|
| D | gpio-keys-polled.txt | 8 - autorepeat: Boolean, Enable auto repeat feature of Linux input
30 - wakeup-source: Boolean, button can wake-up the system.
|
| D | rotary-encoder.txt | 22 - wakeup-source: Boolean, rotary encoder can wake up the system.
|
| D | brcm,bcm-keypad.txt | 58 - autorepeat: Boolean, Enable auto repeat feature of Linux input
|
| /linux-4.4.14/Documentation/devicetree/bindings/ |
| D | common-properties.txt | 9 - big-endian: Boolean; force big endian register accesses
12 - little-endian: Boolean; force little endian register accesses
15 - native-endian: Boolean; always use register accesses matched to the
|
| /linux-4.4.14/Documentation/devicetree/bindings/leds/ |
| D | leds-bcm6328.txt | 30 - brcm,serial-leds : Boolean, enables Serial LEDs.
32 - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
34 - brcm,serial-clk-low : Boolean, makes clock signal active low.
36 - brcm,serial-dat-low : Boolean, makes data signal active low.
38 - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
49 - active-low : Boolean, makes LED active low.
57 - brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
|
| D | leds-bcm6358.txt | 18 - brcm,clk-dat-low : Boolean, makes clock and data signals active low.
28 - active-low : Boolean, makes LED active low.
|
| /linux-4.4.14/Documentation/devicetree/bindings/display/msm/ |
| D | dsi.txt | 33 - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
35 - qcom,master-dsi: Boolean value indicating if the DSI controller is driving
37 - qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
70 - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
|
| /linux-4.4.14/Documentation/devicetree/bindings/arm/tegra/ |
| D | nvidia,tegra20-pmc.txt | 32 - nvidia,core-power-req-active-high : Boolean, core power request active-high
33 - nvidia,sys-clock-req-active-high : Boolean, system clock request active-high
34 - nvidia,combined-power-req : Boolean, combined power request for CPU & Core
35 - nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC)
|
| /linux-4.4.14/Documentation/devicetree/bindings/power_supply/ab8500/ |
| D | charger.txt | 18 Boolean value depicting the presence of 'automatic poweron after powerloss'
|
| /linux-4.4.14/Documentation/devicetree/bindings/display/ |
| D | fsl,dcu.txt | 11 - big-endian Boolean property, LS1021A DCU registers are big-endian.
|
| /linux-4.4.14/Documentation/devicetree/bindings/iio/adc/ |
| D | at91_adc.txt | 23 - atmel,adc-use-external-triggers: Boolean to enable the external triggers
27 - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
|
| /linux-4.4.14/Documentation/devicetree/bindings/pinctrl/ |
| D | lantiq,pinctrl-falcon.txt | 56 - lantiq,drive-current: Boolean, enables drive-current
57 - lantiq,slew-rate: Boolean, enables slew-rate
|
| D | lantiq,pinctrl-xway.txt | 63 - lantiq,open-drain: Boolean, enables open-drain on the defined pin.
|
| /linux-4.4.14/Documentation/devicetree/bindings/sound/ |
| D | rt5640.txt | 18 Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
|
| D | ti,tas5086.txt | 23 - ti,mid-z-channel-X: Boolean properties, X being a number from 1 to 6.
|
| D | rt5677.txt | 28 Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential,
|
| D | rt5645.txt | 20 Boolean. Indicate MIC2 input are differential, rather than single-ended.
|
| D | fsl-sai.txt | 31 - big-endian : Boolean property, required if all the FTM_PWM
|
| /linux-4.4.14/Documentation/devicetree/bindings/i2c/ |
| D | i2c-mux-pca954x.txt | 19 - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
|
| /linux-4.4.14/Documentation/devicetree/bindings/mfd/ |
| D | as3722.txt | 18 - ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on
20 - ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on
129 ams,system-power-controller: Boolean, to enable the power off functionality
|
| /linux-4.4.14/Documentation/devicetree/bindings/usb/ |
| D | atmel-usb.txt | 102 - atmel,can-dma: Boolean to specify if the endpoint support DMA.
103 - atmel,can-isoc: Boolean to specify if the endpoint support ISOC.
|
| /linux-4.4.14/Documentation/devicetree/bindings/regulator/ |
| D | max8907.txt | 21 - maxim,system-power-controller: Boolean property indicating that the PMIC
|
| /linux-4.4.14/Documentation/devicetree/bindings/hwmon/ |
| D | max6697.txt | 41 Boolean for all chips other than MAX6581. Set to enable resistance
|
| /linux-4.4.14/Documentation/devicetree/bindings/pwm/ |
| D | pwm-fsl-ftm.txt | 34 - big-endian: Boolean property, required if the FTM PWM registers use a big-
|
| /linux-4.4.14/Documentation/devicetree/bindings/power/reset/ |
| D | keystone-reset.txt | 26 - ti,soft-reset: Boolean option indicating soft reset.
|
| /linux-4.4.14/Documentation/devicetree/bindings/clock/ |
| D | nvidia,tegra124-dfll.txt | 46 - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
|
| /linux-4.4.14/Documentation/devicetree/bindings/interrupt-controller/ |
| D | arm,gic-v3.txt | 59 - msi-controller : Boolean property. Identifies the node as an MSI controller
|
| /linux-4.4.14/Documentation/fb/ |
| D | intelfb.txt | 111 parameters. The main difference is that you need to include a Boolean value
|
| D | sisfb.txt | 149 Boolean options such as "noaccel" or "noypan" are to be given without a
|
| D | intel810.txt | 201 parameters. The main difference is that you need to include a Boolean value
|
| /linux-4.4.14/Documentation/devicetree/bindings/bus/ |
| D | ti-gpmc.txt | 70 Boolean timing parameters. If property is present parameter enabled and
|
| /linux-4.4.14/Documentation/devicetree/bindings/arm/bcm/ |
| D | brcm,brcmstb.txt | 39 Boolean property, which when present indicates that the chip
|
| /linux-4.4.14/Documentation/video4linux/ |
| D | uvcvideo.txt | 168 UVC_CTRL_DATA_TYPE_BOOLEAN Boolean
|
| D | vivid.txt | 523 The Button, Boolean, Integer 32 Bits, Integer 64 Bits, Menu, String, Bitmask and
|
| /linux-4.4.14/Documentation/filesystems/ |
| D | debugfs.txt | 105 Boolean values can be placed in debugfs with:
|
| /linux-4.4.14/drivers/atm/ |
| D | iphase.h | 157 #define Boolean(x) ((x) ? 1 : 0) macro
|
| /linux-4.4.14/Documentation/networking/ |
| D | cdc_mbim.txt | 22 Type: Boolean
|
| /linux-4.4.14/Documentation/RCU/ |
| D | torture.txt | 164 idle CPUs. Boolean parameter, "1" to test, "0" otherwise.
|
| /linux-4.4.14/Documentation/ |
| D | bcache.txt | 417 Boolean; if on a discard/TRIM will be issued to each bucket before it is
|
| /linux-4.4.14/Documentation/kbuild/ |
| D | kconfig-language.txt | 182 (1) Convert the symbol into an expression. Boolean and tristate symbols
|