| /linux-4.1.27/arch/powerpc/boot/ |
| D | virtex.c | 26 #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ macro
65 out_8(reg_base + (UART_LCR << reg_shift), UART_LCR_WLEN8); in virtex_ns16550_console_init()
|
| /linux-4.1.27/arch/frv/kernel/ |
| D | gdb-io.h | 52 #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ macro
|
| D | gdb-io.c | 57 __UART(LCR) = UART_LCR_WLEN8; /* 1N8 */ in gdbstub_io_init()
|
| /linux-4.1.27/drivers/tty/serial/ |
| D | m32r_sio_reg.h | 120 #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ macro
|
| D | ioc3_serial.c | 111 | UART_LCR_WLEN7 | UART_LCR_WLEN8)
426 writeb(UART_LCR_WLEN8 | 0, &uart->iu_lcr); in port_init()
524 writeb(UART_LCR_WLEN8, &port->ip_uart_regs->iu_lcr); in local_open()
615 sizebits = UART_LCR_WLEN8; in config_port()
|
| D | serial-tegra.c | 80 #define TEGRA_UART_DEFAULT_LSR UART_LCR_WLEN8
1122 lcr &= ~UART_LCR_WLEN8; in tegra_uart_set_termios()
1137 lcr |= UART_LCR_WLEN8; in tegra_uart_set_termios()
|
| D | pxa.c | 378 serial_out(up, UART_LCR, UART_LCR_WLEN8); in serial_pxa_startup()
454 cval = UART_LCR_WLEN8; in serial_pxa_set_termios()
|
| D | vr41xx_siu.c | 471 siu_write(port, UART_LCR, UART_LCR_WLEN8); in siu_startup()
535 lcr = UART_LCR_WLEN8; in siu_set_termios()
|
| D | ioc4_serial.c | 378 | UART_LCR_WLEN7 | UART_LCR_WLEN8)
861 writeb(UART_LCR_WLEN8 | 0, &uart->i4u_lcr); in port_init()
1246 writeb(UART_LCR_WLEN8, &port->ip_uart_regs->i4u_lcr); in local_open()
1337 sizebits = UART_LCR_WLEN8; in config_port()
|
| D | omap-serial.c | 783 serial_out(up, UART_LCR, UART_LCR_WLEN8); in serial_omap_startup()
881 cval = UART_LCR_WLEN8; in serial_omap_set_termios()
|
| D | m32r_sio.c | 710 cval = UART_LCR_WLEN8; in m32r_sio_set_termios()
|
| D | sunsu.c | 691 serial_outp(up, UART_LCR, UART_LCR_WLEN8); in sunsu_startup()
|
| /linux-4.1.27/arch/mn10300/kernel/ |
| D | gdb-io-serial.c | 35 GDBPORT_SERIAL_LCR = UART_LCR_WLEN8; /* 1N8 */ in gdbstub_io_init()
|
| /linux-4.1.27/arch/powerpc/platforms/embedded6xx/ |
| D | ls_uart.c | 60 unsigned char cval = UART_LCR_WLEN8; in avr_uart_configure()
|
| /linux-4.1.27/drivers/usb/serial/ |
| D | ark3116.c | 181 priv->lcr = UART_LCR_WLEN8; in ark3116_port_probe()
182 ark3116_write_reg(serial, UART_LCR, UART_LCR_WLEN8); in ark3116_port_probe()
242 lcr = UART_LCR_WLEN8; in ark3116_set_termios()
|
| D | quatech2.c | 299 new_lcr |= UART_LCR_WLEN8; in qt2_set_termios()
391 DEFAULT_BAUD_RATE, UART_LCR_WLEN8); in qt2_open()
|
| D | ssu100.c | 230 urb_value |= UART_LCR_WLEN8; in ssu100_set_termios()
|
| D | f81232.c | 489 new_lcr |= UART_LCR_WLEN8; in f81232_set_termios()
|
| D | mos7720.c | 1537 lData = UART_LCR_WLEN8; in change_port_settings()
1562 lData = UART_LCR_WLEN8; in change_port_settings()
|
| /linux-4.1.27/drivers/staging/media/lirc/ |
| D | lirc_sir.c | 625 soutp(UART_LCR, UART_LCR_WLEN8); in init_hardware()
782 soutp(UART_LCR, UART_LCR_DLAB | UART_LCR_WLEN8); in init_act200()
789 soutp(UART_LCR, UART_LCR_WLEN8); in init_act200()
|
| /linux-4.1.27/include/uapi/linux/ |
| D | serial_reg.h | 111 #define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ macro
|
| /linux-4.1.27/drivers/bluetooth/ |
| D | btuart_cs.c | 380 lcr = UART_LCR_WLEN8; in btuart_change_speed()
500 outb(UART_LCR_WLEN8, iobase + UART_LCR); /* Reset DLAB */ in btuart_open()
|
| D | dtl1_cs.c | 482 outb(UART_LCR_WLEN8, iobase + UART_LCR); /* Reset DLAB */ in dtl1_open()
|
| /linux-4.1.27/sound/drivers/ |
| D | serial-u16550.c | 349 outb(UART_LCR_WLEN8, io_base + UART_LCR); /* Line Control Register */ in snd_uart16550_detect()
409 outb(UART_LCR_WLEN8 /* 8 data-bits */ in snd_uart16550_do_open()
|
| /linux-4.1.27/drivers/mmc/card/ |
| D | sdio_uart.c | 271 cval = UART_LCR_WLEN8; in sdio_uart_change_speed()
644 sdio_out(port, UART_LCR, UART_LCR_WLEN8); in sdio_uart_activate()
|
| /linux-4.1.27/drivers/tty/serial/8250/ |
| D | 8250_omap.c | 317 cval = UART_LCR_WLEN8; in omap_8250_set_termios()
610 serial_out(up, UART_LCR, UART_LCR_WLEN8); in omap_8250_startup()
|
| D | 8250_core.c | 2279 serial_port_out(port, UART_LCR, UART_LCR_WLEN8); in serial8250_do_startup()
2510 cval = UART_LCR_WLEN8; in serial8250_compute_lcr()
|
| /linux-4.1.27/drivers/isdn/hisax/ |
| D | elsa_ser.c | 172 serial_outp(cs, UART_LCR, UART_LCR_WLEN8); /* reset DLAB */ in mstartup()
|
| /linux-4.1.27/drivers/tty/serial/jsm/ |
| D | jsm_cls.c | 763 lcr |= UART_LCR_WLEN8; in cls_param()
|
| D | jsm_neo.c | 1033 lcr |= UART_LCR_WLEN8; in neo_param()
|
| /linux-4.1.27/drivers/staging/dgnc/ |
| D | dgnc_cls.c | 597 lcr |= UART_LCR_WLEN8; in cls_param()
|
| D | dgnc_neo.c | 753 lcr |= UART_LCR_WLEN8; in neo_param()
|
| /linux-4.1.27/drivers/net/irda/ |
| D | smsc-ircc2.c | 1163 lcr = UART_LCR_WLEN8; in smsc_ircc_set_sir_speed()
1922 outb(UART_LCR_WLEN8, sir_base + UART_LCR); /* Reset DLAB */ in smsc_ircc_sir_start()
|
| D | ali-ircc.c | 1081 lcr = UART_LCR_WLEN8; in ali_ircc_sir_change_speed()
|
| /linux-4.1.27/drivers/tty/ |
| D | mxser.c | 919 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */ in mxser_activate()
|