1/* 2 * linux/include/linux/mmc/host.h 3 * 4 * This program is free software; you can redistribute it and/or modify 5 * it under the terms of the GNU General Public License version 2 as 6 * published by the Free Software Foundation. 7 * 8 * Host driver specific definitions. 9 */ 10#ifndef LINUX_MMC_HOST_H 11#define LINUX_MMC_HOST_H 12 13#include <linux/leds.h> 14#include <linux/mutex.h> 15#include <linux/timer.h> 16#include <linux/sched.h> 17#include <linux/device.h> 18#include <linux/fault-inject.h> 19 20#include <linux/mmc/core.h> 21#include <linux/mmc/card.h> 22#include <linux/mmc/pm.h> 23 24struct mmc_ios { 25 unsigned int clock; /* clock rate */ 26 unsigned short vdd; 27 28/* vdd stores the bit number of the selected voltage range from below. */ 29 30 unsigned char bus_mode; /* command output mode */ 31 32#define MMC_BUSMODE_OPENDRAIN 1 33#define MMC_BUSMODE_PUSHPULL 2 34 35 unsigned char chip_select; /* SPI chip select */ 36 37#define MMC_CS_DONTCARE 0 38#define MMC_CS_HIGH 1 39#define MMC_CS_LOW 2 40 41 unsigned char power_mode; /* power supply mode */ 42 43#define MMC_POWER_OFF 0 44#define MMC_POWER_UP 1 45#define MMC_POWER_ON 2 46#define MMC_POWER_UNDEFINED 3 47 48 unsigned char bus_width; /* data bus width */ 49 50#define MMC_BUS_WIDTH_1 0 51#define MMC_BUS_WIDTH_4 2 52#define MMC_BUS_WIDTH_8 3 53 54 unsigned char timing; /* timing specification used */ 55 56#define MMC_TIMING_LEGACY 0 57#define MMC_TIMING_MMC_HS 1 58#define MMC_TIMING_SD_HS 2 59#define MMC_TIMING_UHS_SDR12 3 60#define MMC_TIMING_UHS_SDR25 4 61#define MMC_TIMING_UHS_SDR50 5 62#define MMC_TIMING_UHS_SDR104 6 63#define MMC_TIMING_UHS_DDR50 7 64#define MMC_TIMING_MMC_DDR52 8 65#define MMC_TIMING_MMC_HS200 9 66#define MMC_TIMING_MMC_HS400 10 67 68 unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */ 69 70#define MMC_SIGNAL_VOLTAGE_330 0 71#define MMC_SIGNAL_VOLTAGE_180 1 72#define MMC_SIGNAL_VOLTAGE_120 2 73 74 unsigned char drv_type; /* driver type (A, B, C, D) */ 75 76#define MMC_SET_DRIVER_TYPE_B 0 77#define MMC_SET_DRIVER_TYPE_A 1 78#define MMC_SET_DRIVER_TYPE_C 2 79#define MMC_SET_DRIVER_TYPE_D 3 80}; 81 82struct mmc_host_ops { 83 /* 84 * It is optional for the host to implement pre_req and post_req in 85 * order to support double buffering of requests (prepare one 86 * request while another request is active). 87 * pre_req() must always be followed by a post_req(). 88 * To undo a call made to pre_req(), call post_req() with 89 * a nonzero err condition. 90 */ 91 void (*post_req)(struct mmc_host *host, struct mmc_request *req, 92 int err); 93 void (*pre_req)(struct mmc_host *host, struct mmc_request *req, 94 bool is_first_req); 95 void (*request)(struct mmc_host *host, struct mmc_request *req); 96 /* 97 * Avoid calling these three functions too often or in a "fast path", 98 * since underlaying controller might implement them in an expensive 99 * and/or slow way. 100 * 101 * Also note that these functions might sleep, so don't call them 102 * in the atomic contexts! 103 * 104 * Return values for the get_ro callback should be: 105 * 0 for a read/write card 106 * 1 for a read-only card 107 * -ENOSYS when not supported (equal to NULL callback) 108 * or a negative errno value when something bad happened 109 * 110 * Return values for the get_cd callback should be: 111 * 0 for a absent card 112 * 1 for a present card 113 * -ENOSYS when not supported (equal to NULL callback) 114 * or a negative errno value when something bad happened 115 */ 116 void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios); 117 int (*get_ro)(struct mmc_host *host); 118 int (*get_cd)(struct mmc_host *host); 119 120 void (*enable_sdio_irq)(struct mmc_host *host, int enable); 121 122 /* optional callback for HC quirks */ 123 void (*init_card)(struct mmc_host *host, struct mmc_card *card); 124 125 int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios); 126 127 /* Check if the card is pulling dat[0:3] low */ 128 int (*card_busy)(struct mmc_host *host); 129 130 /* The tuning command opcode value is different for SD and eMMC cards */ 131 int (*execute_tuning)(struct mmc_host *host, u32 opcode); 132 133 /* Prepare HS400 target operating frequency depending host driver */ 134 int (*prepare_hs400_tuning)(struct mmc_host *host, struct mmc_ios *ios); 135 int (*select_drive_strength)(struct mmc_card *card, 136 unsigned int max_dtr, int host_drv, 137 int card_drv, int *drv_type); 138 void (*hw_reset)(struct mmc_host *host); 139 void (*card_event)(struct mmc_host *host); 140 141 /* 142 * Optional callback to support controllers with HW issues for multiple 143 * I/O. Returns the number of supported blocks for the request. 144 */ 145 int (*multi_io_quirk)(struct mmc_card *card, 146 unsigned int direction, int blk_size); 147}; 148 149struct mmc_card; 150struct device; 151 152struct mmc_async_req { 153 /* active mmc request */ 154 struct mmc_request *mrq; 155 /* 156 * Check error status of completed mmc request. 157 * Returns 0 if success otherwise non zero. 158 */ 159 int (*err_check) (struct mmc_card *, struct mmc_async_req *); 160}; 161 162/** 163 * struct mmc_slot - MMC slot functions 164 * 165 * @cd_irq: MMC/SD-card slot hotplug detection IRQ or -EINVAL 166 * @handler_priv: MMC/SD-card slot context 167 * 168 * Some MMC/SD host controllers implement slot-functions like card and 169 * write-protect detection natively. However, a large number of controllers 170 * leave these functions to the CPU. This struct provides a hook to attach 171 * such slot-function drivers. 172 */ 173struct mmc_slot { 174 int cd_irq; 175 void *handler_priv; 176}; 177 178/** 179 * mmc_context_info - synchronization details for mmc context 180 * @is_done_rcv wake up reason was done request 181 * @is_new_req wake up reason was new request 182 * @is_waiting_last_req mmc context waiting for single running request 183 * @wait wait queue 184 * @lock lock to protect data fields 185 */ 186struct mmc_context_info { 187 bool is_done_rcv; 188 bool is_new_req; 189 bool is_waiting_last_req; 190 wait_queue_head_t wait; 191 spinlock_t lock; 192}; 193 194struct regulator; 195struct mmc_pwrseq; 196 197struct mmc_supply { 198 struct regulator *vmmc; /* Card power supply */ 199 struct regulator *vqmmc; /* Optional Vccq supply */ 200}; 201 202struct mmc_host { 203 struct device *parent; 204 struct device class_dev; 205 int index; 206 const struct mmc_host_ops *ops; 207 struct mmc_pwrseq *pwrseq; 208 unsigned int f_min; 209 unsigned int f_max; 210 unsigned int f_init; 211 u32 ocr_avail; 212 u32 ocr_avail_sdio; /* SDIO-specific OCR */ 213 u32 ocr_avail_sd; /* SD-specific OCR */ 214 u32 ocr_avail_mmc; /* MMC-specific OCR */ 215 struct notifier_block pm_notify; 216 u32 max_current_330; 217 u32 max_current_300; 218 u32 max_current_180; 219 220#define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */ 221#define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */ 222#define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */ 223#define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */ 224#define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */ 225#define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */ 226#define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */ 227#define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */ 228#define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */ 229#define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */ 230#define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */ 231#define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */ 232#define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */ 233#define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */ 234#define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */ 235#define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */ 236#define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */ 237 238 u32 caps; /* Host capabilities */ 239 240#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */ 241#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */ 242#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */ 243#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */ 244#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ 245#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ 246#define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */ 247#define MMC_CAP_AGGRESSIVE_PM (1 << 7) /* Suspend (e)MMC/SD at idle */ 248#define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */ 249#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */ 250#define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */ 251#define MMC_CAP_1_8V_DDR (1 << 11) /* can support */ 252 /* DDR mode at 1.8V */ 253#define MMC_CAP_1_2V_DDR (1 << 12) /* can support */ 254 /* DDR mode at 1.2V */ 255#define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */ 256#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */ 257#define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */ 258#define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */ 259#define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */ 260#define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */ 261#define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */ 262#define MMC_CAP_RUNTIME_RESUME (1 << 20) /* Resume at runtime_resume. */ 263#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */ 264#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */ 265#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */ 266#define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */ 267#define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */ 268 269 u32 caps2; /* More host capabilities */ 270 271#define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */ 272#define MMC_CAP2_FULL_PWR_CYCLE (1 << 2) /* Can do full power cycle */ 273#define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */ 274#define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */ 275#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \ 276 MMC_CAP2_HS200_1_2V_SDR) 277#define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */ 278#define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */ 279#define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */ 280#define MMC_CAP2_PACKED_RD (1 << 12) /* Allow packed read */ 281#define MMC_CAP2_PACKED_WR (1 << 13) /* Allow packed write */ 282#define MMC_CAP2_PACKED_CMD (MMC_CAP2_PACKED_RD | \ 283 MMC_CAP2_PACKED_WR) 284#define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */ 285#define MMC_CAP2_HS400_1_8V (1 << 15) /* Can support HS400 1.8V */ 286#define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */ 287#define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \ 288 MMC_CAP2_HS400_1_2V) 289#define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V) 290#define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17) 291#define MMC_CAP2_NO_WRITE_PROTECT (1 << 18) /* No physical write protect pin, assume that card is always read-write */ 292 293 mmc_pm_flag_t pm_caps; /* supported pm features */ 294 295 /* host specific block data */ 296 unsigned int max_seg_size; /* see blk_queue_max_segment_size */ 297 unsigned short max_segs; /* see blk_queue_max_segments */ 298 unsigned short unused; 299 unsigned int max_req_size; /* maximum number of bytes in one req */ 300 unsigned int max_blk_size; /* maximum size of one mmc block */ 301 unsigned int max_blk_count; /* maximum number of blocks in one req */ 302 unsigned int max_busy_timeout; /* max busy timeout in ms */ 303 304 /* private data */ 305 spinlock_t lock; /* lock for claim and bus ops */ 306 307 struct mmc_ios ios; /* current io bus settings */ 308 309 /* group bitfields together to minimize padding */ 310 unsigned int use_spi_crc:1; 311 unsigned int claimed:1; /* host exclusively claimed */ 312 unsigned int bus_dead:1; /* bus has been released */ 313#ifdef CONFIG_MMC_DEBUG 314 unsigned int removed:1; /* host is being removed */ 315#endif 316 unsigned int can_retune:1; /* re-tuning can be used */ 317 unsigned int doing_retune:1; /* re-tuning in progress */ 318 unsigned int retune_now:1; /* do re-tuning at next req */ 319 320 int rescan_disable; /* disable card detection */ 321 int rescan_entered; /* used with nonremovable devices */ 322 323 int need_retune; /* re-tuning is needed */ 324 int hold_retune; /* hold off re-tuning */ 325 unsigned int retune_period; /* re-tuning period in secs */ 326 struct timer_list retune_timer; /* for periodic re-tuning */ 327 328 bool trigger_card_event; /* card_event necessary */ 329 330 struct mmc_card *card; /* device attached to this host */ 331 332 wait_queue_head_t wq; 333 struct task_struct *claimer; /* task that has host claimed */ 334 int claim_cnt; /* "claim" nesting count */ 335 336 struct delayed_work detect; 337 int detect_change; /* card detect flag */ 338 struct mmc_slot slot; 339 340 const struct mmc_bus_ops *bus_ops; /* current bus driver */ 341 unsigned int bus_refs; /* reference counter */ 342 343 unsigned int sdio_irqs; 344 struct task_struct *sdio_irq_thread; 345 bool sdio_irq_pending; 346 atomic_t sdio_irq_thread_abort; 347 348 mmc_pm_flag_t pm_flags; /* requested pm features */ 349 350 struct led_trigger *led; /* activity led */ 351 352#ifdef CONFIG_REGULATOR 353 bool regulator_enabled; /* regulator state */ 354#endif 355 struct mmc_supply supply; 356 357 struct dentry *debugfs_root; 358 359 struct mmc_async_req *areq; /* active async req */ 360 struct mmc_context_info context_info; /* async synchronization info */ 361 362#ifdef CONFIG_FAIL_MMC_REQUEST 363 struct fault_attr fail_mmc_request; 364#endif 365 366 unsigned int actual_clock; /* Actual HC clock rate */ 367 368 unsigned int slotno; /* used for sdio acpi binding */ 369 370 int dsr_req; /* DSR value is valid */ 371 u32 dsr; /* optional driver stage (DSR) value */ 372 373 unsigned long private[0] ____cacheline_aligned; 374}; 375 376struct mmc_host *mmc_alloc_host(int extra, struct device *); 377int mmc_add_host(struct mmc_host *); 378void mmc_remove_host(struct mmc_host *); 379void mmc_free_host(struct mmc_host *); 380int mmc_of_parse(struct mmc_host *host); 381 382static inline void *mmc_priv(struct mmc_host *host) 383{ 384 return (void *)host->private; 385} 386 387#define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI) 388 389#define mmc_dev(x) ((x)->parent) 390#define mmc_classdev(x) (&(x)->class_dev) 391#define mmc_hostname(x) (dev_name(&(x)->class_dev)) 392 393int mmc_power_save_host(struct mmc_host *host); 394int mmc_power_restore_host(struct mmc_host *host); 395 396void mmc_detect_change(struct mmc_host *, unsigned long delay); 397void mmc_request_done(struct mmc_host *, struct mmc_request *); 398 399static inline void mmc_signal_sdio_irq(struct mmc_host *host) 400{ 401 host->ops->enable_sdio_irq(host, 0); 402 host->sdio_irq_pending = true; 403 if (host->sdio_irq_thread) 404 wake_up_process(host->sdio_irq_thread); 405} 406 407void sdio_run_irqs(struct mmc_host *host); 408 409#ifdef CONFIG_REGULATOR 410int mmc_regulator_get_ocrmask(struct regulator *supply); 411int mmc_regulator_set_ocr(struct mmc_host *mmc, 412 struct regulator *supply, 413 unsigned short vdd_bit); 414int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios); 415#else 416static inline int mmc_regulator_get_ocrmask(struct regulator *supply) 417{ 418 return 0; 419} 420 421static inline int mmc_regulator_set_ocr(struct mmc_host *mmc, 422 struct regulator *supply, 423 unsigned short vdd_bit) 424{ 425 return 0; 426} 427 428static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc, 429 struct mmc_ios *ios) 430{ 431 return -EINVAL; 432} 433#endif 434 435int mmc_regulator_get_supply(struct mmc_host *mmc); 436 437int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *); 438 439static inline int mmc_card_is_removable(struct mmc_host *host) 440{ 441 return !(host->caps & MMC_CAP_NONREMOVABLE); 442} 443 444static inline int mmc_card_keep_power(struct mmc_host *host) 445{ 446 return host->pm_flags & MMC_PM_KEEP_POWER; 447} 448 449static inline int mmc_card_wake_sdio_irq(struct mmc_host *host) 450{ 451 return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ; 452} 453 454static inline int mmc_host_cmd23(struct mmc_host *host) 455{ 456 return host->caps & MMC_CAP_CMD23; 457} 458 459static inline int mmc_boot_partition_access(struct mmc_host *host) 460{ 461 return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC); 462} 463 464static inline int mmc_host_uhs(struct mmc_host *host) 465{ 466 return host->caps & 467 (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | 468 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | 469 MMC_CAP_UHS_DDR50); 470} 471 472static inline int mmc_host_packed_wr(struct mmc_host *host) 473{ 474 return host->caps2 & MMC_CAP2_PACKED_WR; 475} 476 477static inline int mmc_card_hs(struct mmc_card *card) 478{ 479 return card->host->ios.timing == MMC_TIMING_SD_HS || 480 card->host->ios.timing == MMC_TIMING_MMC_HS; 481} 482 483static inline int mmc_card_uhs(struct mmc_card *card) 484{ 485 return card->host->ios.timing >= MMC_TIMING_UHS_SDR12 && 486 card->host->ios.timing <= MMC_TIMING_UHS_DDR50; 487} 488 489static inline bool mmc_card_hs200(struct mmc_card *card) 490{ 491 return card->host->ios.timing == MMC_TIMING_MMC_HS200; 492} 493 494static inline bool mmc_card_ddr52(struct mmc_card *card) 495{ 496 return card->host->ios.timing == MMC_TIMING_MMC_DDR52; 497} 498 499static inline bool mmc_card_hs400(struct mmc_card *card) 500{ 501 return card->host->ios.timing == MMC_TIMING_MMC_HS400; 502} 503 504void mmc_retune_timer_stop(struct mmc_host *host); 505 506static inline void mmc_retune_needed(struct mmc_host *host) 507{ 508 if (host->can_retune) 509 host->need_retune = 1; 510} 511 512static inline void mmc_retune_recheck(struct mmc_host *host) 513{ 514 if (host->hold_retune <= 1) 515 host->retune_now = 1; 516} 517 518#endif /* LINUX_MMC_HOST_H */ 519