1/* 2 * Driver for msm7k serial device and console 3 * 4 * Copyright (C) 2007 Google, Inc. 5 * Author: Robert Love <rlove@google.com> 6 * Copyright (c) 2011, Code Aurora Forum. All rights reserved. 7 * 8 * This software is licensed under the terms of the GNU General Public 9 * License version 2, as published by the Free Software Foundation, and 10 * may be copied, distributed, and modified under those terms. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 */ 17 18#if defined(CONFIG_SERIAL_MSM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 19# define SUPPORT_SYSRQ 20#endif 21 22#include <linux/atomic.h> 23#include <linux/dma-mapping.h> 24#include <linux/dmaengine.h> 25#include <linux/hrtimer.h> 26#include <linux/module.h> 27#include <linux/io.h> 28#include <linux/ioport.h> 29#include <linux/irq.h> 30#include <linux/init.h> 31#include <linux/console.h> 32#include <linux/tty.h> 33#include <linux/tty_flip.h> 34#include <linux/serial_core.h> 35#include <linux/serial.h> 36#include <linux/slab.h> 37#include <linux/clk.h> 38#include <linux/platform_device.h> 39#include <linux/delay.h> 40#include <linux/of.h> 41#include <linux/of_device.h> 42 43#include "msm_serial.h" 44 45#define UARTDM_BURST_SIZE 16 /* in bytes */ 46#define UARTDM_TX_AIGN(x) ((x) & ~0x3) /* valid for > 1p3 */ 47#define UARTDM_TX_MAX 256 /* in bytes, valid for <= 1p3 */ 48#define UARTDM_RX_SIZE (UART_XMIT_SIZE / 4) 49 50enum { 51 UARTDM_1P1 = 1, 52 UARTDM_1P2, 53 UARTDM_1P3, 54 UARTDM_1P4, 55}; 56 57struct msm_dma { 58 struct dma_chan *chan; 59 enum dma_data_direction dir; 60 dma_addr_t phys; 61 unsigned char *virt; 62 dma_cookie_t cookie; 63 u32 enable_bit; 64 unsigned int count; 65 struct dma_async_tx_descriptor *desc; 66}; 67 68struct msm_port { 69 struct uart_port uart; 70 char name[16]; 71 struct clk *clk; 72 struct clk *pclk; 73 unsigned int imr; 74 int is_uartdm; 75 unsigned int old_snap_state; 76 bool break_detected; 77 struct msm_dma tx_dma; 78 struct msm_dma rx_dma; 79}; 80 81static void msm_handle_tx(struct uart_port *port); 82static void msm_start_rx_dma(struct msm_port *msm_port); 83 84void msm_stop_dma(struct uart_port *port, struct msm_dma *dma) 85{ 86 struct device *dev = port->dev; 87 unsigned int mapped; 88 u32 val; 89 90 mapped = dma->count; 91 dma->count = 0; 92 93 dmaengine_terminate_all(dma->chan); 94 95 /* 96 * DMA Stall happens if enqueue and flush command happens concurrently. 97 * For example before changing the baud rate/protocol configuration and 98 * sending flush command to ADM, disable the channel of UARTDM. 99 * Note: should not reset the receiver here immediately as it is not 100 * suggested to do disable/reset or reset/disable at the same time. 101 */ 102 val = msm_read(port, UARTDM_DMEN); 103 val &= ~dma->enable_bit; 104 msm_write(port, val, UARTDM_DMEN); 105 106 if (mapped) 107 dma_unmap_single(dev, dma->phys, mapped, dma->dir); 108} 109 110static void msm_release_dma(struct msm_port *msm_port) 111{ 112 struct msm_dma *dma; 113 114 dma = &msm_port->tx_dma; 115 if (dma->chan) { 116 msm_stop_dma(&msm_port->uart, dma); 117 dma_release_channel(dma->chan); 118 } 119 120 memset(dma, 0, sizeof(*dma)); 121 122 dma = &msm_port->rx_dma; 123 if (dma->chan) { 124 msm_stop_dma(&msm_port->uart, dma); 125 dma_release_channel(dma->chan); 126 kfree(dma->virt); 127 } 128 129 memset(dma, 0, sizeof(*dma)); 130} 131 132static void msm_request_tx_dma(struct msm_port *msm_port, resource_size_t base) 133{ 134 struct device *dev = msm_port->uart.dev; 135 struct dma_slave_config conf; 136 struct msm_dma *dma; 137 u32 crci = 0; 138 int ret; 139 140 dma = &msm_port->tx_dma; 141 142 /* allocate DMA resources, if available */ 143 dma->chan = dma_request_slave_channel_reason(dev, "tx"); 144 if (IS_ERR(dma->chan)) 145 goto no_tx; 146 147 of_property_read_u32(dev->of_node, "qcom,tx-crci", &crci); 148 149 memset(&conf, 0, sizeof(conf)); 150 conf.direction = DMA_MEM_TO_DEV; 151 conf.device_fc = true; 152 conf.dst_addr = base + UARTDM_TF; 153 conf.dst_maxburst = UARTDM_BURST_SIZE; 154 conf.slave_id = crci; 155 156 ret = dmaengine_slave_config(dma->chan, &conf); 157 if (ret) 158 goto rel_tx; 159 160 dma->dir = DMA_TO_DEVICE; 161 162 if (msm_port->is_uartdm < UARTDM_1P4) 163 dma->enable_bit = UARTDM_DMEN_TX_DM_ENABLE; 164 else 165 dma->enable_bit = UARTDM_DMEN_TX_BAM_ENABLE; 166 167 return; 168 169rel_tx: 170 dma_release_channel(dma->chan); 171no_tx: 172 memset(dma, 0, sizeof(*dma)); 173} 174 175static void msm_request_rx_dma(struct msm_port *msm_port, resource_size_t base) 176{ 177 struct device *dev = msm_port->uart.dev; 178 struct dma_slave_config conf; 179 struct msm_dma *dma; 180 u32 crci = 0; 181 int ret; 182 183 dma = &msm_port->rx_dma; 184 185 /* allocate DMA resources, if available */ 186 dma->chan = dma_request_slave_channel_reason(dev, "rx"); 187 if (IS_ERR(dma->chan)) 188 goto no_rx; 189 190 of_property_read_u32(dev->of_node, "qcom,rx-crci", &crci); 191 192 dma->virt = kzalloc(UARTDM_RX_SIZE, GFP_KERNEL); 193 if (!dma->virt) 194 goto rel_rx; 195 196 memset(&conf, 0, sizeof(conf)); 197 conf.direction = DMA_DEV_TO_MEM; 198 conf.device_fc = true; 199 conf.src_addr = base + UARTDM_RF; 200 conf.src_maxburst = UARTDM_BURST_SIZE; 201 conf.slave_id = crci; 202 203 ret = dmaengine_slave_config(dma->chan, &conf); 204 if (ret) 205 goto err; 206 207 dma->dir = DMA_FROM_DEVICE; 208 209 if (msm_port->is_uartdm < UARTDM_1P4) 210 dma->enable_bit = UARTDM_DMEN_RX_DM_ENABLE; 211 else 212 dma->enable_bit = UARTDM_DMEN_RX_BAM_ENABLE; 213 214 return; 215err: 216 kfree(dma->virt); 217rel_rx: 218 dma_release_channel(dma->chan); 219no_rx: 220 memset(dma, 0, sizeof(*dma)); 221} 222 223static inline void msm_wait_for_xmitr(struct uart_port *port) 224{ 225 while (!(msm_read(port, UART_SR) & UART_SR_TX_EMPTY)) { 226 if (msm_read(port, UART_ISR) & UART_ISR_TX_READY) 227 break; 228 udelay(1); 229 } 230 msm_write(port, UART_CR_CMD_RESET_TX_READY, UART_CR); 231} 232 233static void msm_stop_tx(struct uart_port *port) 234{ 235 struct msm_port *msm_port = UART_TO_MSM(port); 236 237 msm_port->imr &= ~UART_IMR_TXLEV; 238 msm_write(port, msm_port->imr, UART_IMR); 239} 240 241static void msm_start_tx(struct uart_port *port) 242{ 243 struct msm_port *msm_port = UART_TO_MSM(port); 244 struct msm_dma *dma = &msm_port->tx_dma; 245 246 /* Already started in DMA mode */ 247 if (dma->count) 248 return; 249 250 msm_port->imr |= UART_IMR_TXLEV; 251 msm_write(port, msm_port->imr, UART_IMR); 252} 253 254static void msm_reset_dm_count(struct uart_port *port, int count) 255{ 256 msm_wait_for_xmitr(port); 257 msm_write(port, count, UARTDM_NCF_TX); 258 msm_read(port, UARTDM_NCF_TX); 259} 260 261static void msm_complete_tx_dma(void *args) 262{ 263 struct msm_port *msm_port = args; 264 struct uart_port *port = &msm_port->uart; 265 struct circ_buf *xmit = &port->state->xmit; 266 struct msm_dma *dma = &msm_port->tx_dma; 267 struct dma_tx_state state; 268 enum dma_status status; 269 unsigned long flags; 270 unsigned int count; 271 u32 val; 272 273 spin_lock_irqsave(&port->lock, flags); 274 275 /* Already stopped */ 276 if (!dma->count) 277 goto done; 278 279 status = dmaengine_tx_status(dma->chan, dma->cookie, &state); 280 281 dma_unmap_single(port->dev, dma->phys, dma->count, dma->dir); 282 283 val = msm_read(port, UARTDM_DMEN); 284 val &= ~dma->enable_bit; 285 msm_write(port, val, UARTDM_DMEN); 286 287 if (msm_port->is_uartdm > UARTDM_1P3) { 288 msm_write(port, UART_CR_CMD_RESET_TX, UART_CR); 289 msm_write(port, UART_CR_TX_ENABLE, UART_CR); 290 } 291 292 count = dma->count - state.residue; 293 port->icount.tx += count; 294 dma->count = 0; 295 296 xmit->tail += count; 297 xmit->tail &= UART_XMIT_SIZE - 1; 298 299 /* Restore "Tx FIFO below watermark" interrupt */ 300 msm_port->imr |= UART_IMR_TXLEV; 301 msm_write(port, msm_port->imr, UART_IMR); 302 303 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 304 uart_write_wakeup(port); 305 306 msm_handle_tx(port); 307done: 308 spin_unlock_irqrestore(&port->lock, flags); 309} 310 311static int msm_handle_tx_dma(struct msm_port *msm_port, unsigned int count) 312{ 313 struct circ_buf *xmit = &msm_port->uart.state->xmit; 314 struct uart_port *port = &msm_port->uart; 315 struct msm_dma *dma = &msm_port->tx_dma; 316 void *cpu_addr; 317 int ret; 318 u32 val; 319 320 cpu_addr = &xmit->buf[xmit->tail]; 321 322 dma->phys = dma_map_single(port->dev, cpu_addr, count, dma->dir); 323 ret = dma_mapping_error(port->dev, dma->phys); 324 if (ret) 325 return ret; 326 327 dma->desc = dmaengine_prep_slave_single(dma->chan, dma->phys, 328 count, DMA_MEM_TO_DEV, 329 DMA_PREP_INTERRUPT | 330 DMA_PREP_FENCE); 331 if (!dma->desc) { 332 ret = -EIO; 333 goto unmap; 334 } 335 336 dma->desc->callback = msm_complete_tx_dma; 337 dma->desc->callback_param = msm_port; 338 339 dma->cookie = dmaengine_submit(dma->desc); 340 ret = dma_submit_error(dma->cookie); 341 if (ret) 342 goto unmap; 343 344 /* 345 * Using DMA complete for Tx FIFO reload, no need for 346 * "Tx FIFO below watermark" one, disable it 347 */ 348 msm_port->imr &= ~UART_IMR_TXLEV; 349 msm_write(port, msm_port->imr, UART_IMR); 350 351 dma->count = count; 352 353 val = msm_read(port, UARTDM_DMEN); 354 val |= dma->enable_bit; 355 356 if (msm_port->is_uartdm < UARTDM_1P4) 357 msm_write(port, val, UARTDM_DMEN); 358 359 msm_reset_dm_count(port, count); 360 361 if (msm_port->is_uartdm > UARTDM_1P3) 362 msm_write(port, val, UARTDM_DMEN); 363 364 dma_async_issue_pending(dma->chan); 365 return 0; 366unmap: 367 dma_unmap_single(port->dev, dma->phys, count, dma->dir); 368 return ret; 369} 370 371static void msm_complete_rx_dma(void *args) 372{ 373 struct msm_port *msm_port = args; 374 struct uart_port *port = &msm_port->uart; 375 struct tty_port *tport = &port->state->port; 376 struct msm_dma *dma = &msm_port->rx_dma; 377 int count = 0, i, sysrq; 378 unsigned long flags; 379 u32 val; 380 381 spin_lock_irqsave(&port->lock, flags); 382 383 /* Already stopped */ 384 if (!dma->count) 385 goto done; 386 387 val = msm_read(port, UARTDM_DMEN); 388 val &= ~dma->enable_bit; 389 msm_write(port, val, UARTDM_DMEN); 390 391 /* Restore interrupts */ 392 msm_port->imr |= UART_IMR_RXLEV | UART_IMR_RXSTALE; 393 msm_write(port, msm_port->imr, UART_IMR); 394 395 if (msm_read(port, UART_SR) & UART_SR_OVERRUN) { 396 port->icount.overrun++; 397 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 398 msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); 399 } 400 401 count = msm_read(port, UARTDM_RX_TOTAL_SNAP); 402 403 port->icount.rx += count; 404 405 dma->count = 0; 406 407 dma_unmap_single(port->dev, dma->phys, UARTDM_RX_SIZE, dma->dir); 408 409 for (i = 0; i < count; i++) { 410 char flag = TTY_NORMAL; 411 412 if (msm_port->break_detected && dma->virt[i] == 0) { 413 port->icount.brk++; 414 flag = TTY_BREAK; 415 msm_port->break_detected = false; 416 if (uart_handle_break(port)) 417 continue; 418 } 419 420 if (!(port->read_status_mask & UART_SR_RX_BREAK)) 421 flag = TTY_NORMAL; 422 423 spin_unlock_irqrestore(&port->lock, flags); 424 sysrq = uart_handle_sysrq_char(port, dma->virt[i]); 425 spin_lock_irqsave(&port->lock, flags); 426 if (!sysrq) 427 tty_insert_flip_char(tport, dma->virt[i], flag); 428 } 429 430 msm_start_rx_dma(msm_port); 431done: 432 spin_unlock_irqrestore(&port->lock, flags); 433 434 if (count) 435 tty_flip_buffer_push(tport); 436} 437 438static void msm_start_rx_dma(struct msm_port *msm_port) 439{ 440 struct msm_dma *dma = &msm_port->rx_dma; 441 struct uart_port *uart = &msm_port->uart; 442 u32 val; 443 int ret; 444 445 if (!dma->chan) 446 return; 447 448 dma->phys = dma_map_single(uart->dev, dma->virt, 449 UARTDM_RX_SIZE, dma->dir); 450 ret = dma_mapping_error(uart->dev, dma->phys); 451 if (ret) 452 return; 453 454 dma->desc = dmaengine_prep_slave_single(dma->chan, dma->phys, 455 UARTDM_RX_SIZE, DMA_DEV_TO_MEM, 456 DMA_PREP_INTERRUPT); 457 if (!dma->desc) 458 goto unmap; 459 460 dma->desc->callback = msm_complete_rx_dma; 461 dma->desc->callback_param = msm_port; 462 463 dma->cookie = dmaengine_submit(dma->desc); 464 ret = dma_submit_error(dma->cookie); 465 if (ret) 466 goto unmap; 467 /* 468 * Using DMA for FIFO off-load, no need for "Rx FIFO over 469 * watermark" or "stale" interrupts, disable them 470 */ 471 msm_port->imr &= ~(UART_IMR_RXLEV | UART_IMR_RXSTALE); 472 473 /* 474 * Well, when DMA is ADM3 engine(implied by <= UARTDM v1.3), 475 * we need RXSTALE to flush input DMA fifo to memory 476 */ 477 if (msm_port->is_uartdm < UARTDM_1P4) 478 msm_port->imr |= UART_IMR_RXSTALE; 479 480 msm_write(uart, msm_port->imr, UART_IMR); 481 482 dma->count = UARTDM_RX_SIZE; 483 484 dma_async_issue_pending(dma->chan); 485 486 msm_write(uart, UART_CR_CMD_RESET_STALE_INT, UART_CR); 487 msm_write(uart, UART_CR_CMD_STALE_EVENT_ENABLE, UART_CR); 488 489 val = msm_read(uart, UARTDM_DMEN); 490 val |= dma->enable_bit; 491 492 if (msm_port->is_uartdm < UARTDM_1P4) 493 msm_write(uart, val, UARTDM_DMEN); 494 495 msm_write(uart, UARTDM_RX_SIZE, UARTDM_DMRX); 496 497 if (msm_port->is_uartdm > UARTDM_1P3) 498 msm_write(uart, val, UARTDM_DMEN); 499 500 return; 501unmap: 502 dma_unmap_single(uart->dev, dma->phys, UARTDM_RX_SIZE, dma->dir); 503} 504 505static void msm_stop_rx(struct uart_port *port) 506{ 507 struct msm_port *msm_port = UART_TO_MSM(port); 508 struct msm_dma *dma = &msm_port->rx_dma; 509 510 msm_port->imr &= ~(UART_IMR_RXLEV | UART_IMR_RXSTALE); 511 msm_write(port, msm_port->imr, UART_IMR); 512 513 if (dma->chan) 514 msm_stop_dma(port, dma); 515} 516 517static void msm_enable_ms(struct uart_port *port) 518{ 519 struct msm_port *msm_port = UART_TO_MSM(port); 520 521 msm_port->imr |= UART_IMR_DELTA_CTS; 522 msm_write(port, msm_port->imr, UART_IMR); 523} 524 525static void msm_handle_rx_dm(struct uart_port *port, unsigned int misr) 526{ 527 struct tty_port *tport = &port->state->port; 528 unsigned int sr; 529 int count = 0; 530 struct msm_port *msm_port = UART_TO_MSM(port); 531 532 if ((msm_read(port, UART_SR) & UART_SR_OVERRUN)) { 533 port->icount.overrun++; 534 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 535 msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); 536 } 537 538 if (misr & UART_IMR_RXSTALE) { 539 count = msm_read(port, UARTDM_RX_TOTAL_SNAP) - 540 msm_port->old_snap_state; 541 msm_port->old_snap_state = 0; 542 } else { 543 count = 4 * (msm_read(port, UART_RFWR)); 544 msm_port->old_snap_state += count; 545 } 546 547 /* TODO: Precise error reporting */ 548 549 port->icount.rx += count; 550 551 while (count > 0) { 552 unsigned char buf[4]; 553 int sysrq, r_count, i; 554 555 sr = msm_read(port, UART_SR); 556 if ((sr & UART_SR_RX_READY) == 0) { 557 msm_port->old_snap_state -= count; 558 break; 559 } 560 561 ioread32_rep(port->membase + UARTDM_RF, buf, 1); 562 r_count = min_t(int, count, sizeof(buf)); 563 564 for (i = 0; i < r_count; i++) { 565 char flag = TTY_NORMAL; 566 567 if (msm_port->break_detected && buf[i] == 0) { 568 port->icount.brk++; 569 flag = TTY_BREAK; 570 msm_port->break_detected = false; 571 if (uart_handle_break(port)) 572 continue; 573 } 574 575 if (!(port->read_status_mask & UART_SR_RX_BREAK)) 576 flag = TTY_NORMAL; 577 578 spin_unlock(&port->lock); 579 sysrq = uart_handle_sysrq_char(port, buf[i]); 580 spin_lock(&port->lock); 581 if (!sysrq) 582 tty_insert_flip_char(tport, buf[i], flag); 583 } 584 count -= r_count; 585 } 586 587 spin_unlock(&port->lock); 588 tty_flip_buffer_push(tport); 589 spin_lock(&port->lock); 590 591 if (misr & (UART_IMR_RXSTALE)) 592 msm_write(port, UART_CR_CMD_RESET_STALE_INT, UART_CR); 593 msm_write(port, 0xFFFFFF, UARTDM_DMRX); 594 msm_write(port, UART_CR_CMD_STALE_EVENT_ENABLE, UART_CR); 595 596 /* Try to use DMA */ 597 msm_start_rx_dma(msm_port); 598} 599 600static void msm_handle_rx(struct uart_port *port) 601{ 602 struct tty_port *tport = &port->state->port; 603 unsigned int sr; 604 605 /* 606 * Handle overrun. My understanding of the hardware is that overrun 607 * is not tied to the RX buffer, so we handle the case out of band. 608 */ 609 if ((msm_read(port, UART_SR) & UART_SR_OVERRUN)) { 610 port->icount.overrun++; 611 tty_insert_flip_char(tport, 0, TTY_OVERRUN); 612 msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); 613 } 614 615 /* and now the main RX loop */ 616 while ((sr = msm_read(port, UART_SR)) & UART_SR_RX_READY) { 617 unsigned int c; 618 char flag = TTY_NORMAL; 619 int sysrq; 620 621 c = msm_read(port, UART_RF); 622 623 if (sr & UART_SR_RX_BREAK) { 624 port->icount.brk++; 625 if (uart_handle_break(port)) 626 continue; 627 } else if (sr & UART_SR_PAR_FRAME_ERR) { 628 port->icount.frame++; 629 } else { 630 port->icount.rx++; 631 } 632 633 /* Mask conditions we're ignorning. */ 634 sr &= port->read_status_mask; 635 636 if (sr & UART_SR_RX_BREAK) 637 flag = TTY_BREAK; 638 else if (sr & UART_SR_PAR_FRAME_ERR) 639 flag = TTY_FRAME; 640 641 spin_unlock(&port->lock); 642 sysrq = uart_handle_sysrq_char(port, c); 643 spin_lock(&port->lock); 644 if (!sysrq) 645 tty_insert_flip_char(tport, c, flag); 646 } 647 648 spin_unlock(&port->lock); 649 tty_flip_buffer_push(tport); 650 spin_lock(&port->lock); 651} 652 653static void msm_handle_tx_pio(struct uart_port *port, unsigned int tx_count) 654{ 655 struct circ_buf *xmit = &port->state->xmit; 656 struct msm_port *msm_port = UART_TO_MSM(port); 657 unsigned int num_chars; 658 unsigned int tf_pointer = 0; 659 void __iomem *tf; 660 661 if (msm_port->is_uartdm) 662 tf = port->membase + UARTDM_TF; 663 else 664 tf = port->membase + UART_TF; 665 666 if (tx_count && msm_port->is_uartdm) 667 msm_reset_dm_count(port, tx_count); 668 669 while (tf_pointer < tx_count) { 670 int i; 671 char buf[4] = { 0 }; 672 673 if (!(msm_read(port, UART_SR) & UART_SR_TX_READY)) 674 break; 675 676 if (msm_port->is_uartdm) 677 num_chars = min(tx_count - tf_pointer, 678 (unsigned int)sizeof(buf)); 679 else 680 num_chars = 1; 681 682 for (i = 0; i < num_chars; i++) { 683 buf[i] = xmit->buf[xmit->tail + i]; 684 port->icount.tx++; 685 } 686 687 iowrite32_rep(tf, buf, 1); 688 xmit->tail = (xmit->tail + num_chars) & (UART_XMIT_SIZE - 1); 689 tf_pointer += num_chars; 690 } 691 692 /* disable tx interrupts if nothing more to send */ 693 if (uart_circ_empty(xmit)) 694 msm_stop_tx(port); 695 696 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 697 uart_write_wakeup(port); 698} 699 700static void msm_handle_tx(struct uart_port *port) 701{ 702 struct msm_port *msm_port = UART_TO_MSM(port); 703 struct circ_buf *xmit = &msm_port->uart.state->xmit; 704 struct msm_dma *dma = &msm_port->tx_dma; 705 unsigned int pio_count, dma_count, dma_min; 706 void __iomem *tf; 707 int err = 0; 708 709 if (port->x_char) { 710 if (msm_port->is_uartdm) 711 tf = port->membase + UARTDM_TF; 712 else 713 tf = port->membase + UART_TF; 714 715 if (msm_port->is_uartdm) 716 msm_reset_dm_count(port, 1); 717 718 iowrite8_rep(tf, &port->x_char, 1); 719 port->icount.tx++; 720 port->x_char = 0; 721 return; 722 } 723 724 if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { 725 msm_stop_tx(port); 726 return; 727 } 728 729 pio_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE); 730 dma_count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); 731 732 dma_min = 1; /* Always DMA */ 733 if (msm_port->is_uartdm > UARTDM_1P3) { 734 dma_count = UARTDM_TX_AIGN(dma_count); 735 dma_min = UARTDM_BURST_SIZE; 736 } else { 737 if (dma_count > UARTDM_TX_MAX) 738 dma_count = UARTDM_TX_MAX; 739 } 740 741 if (pio_count > port->fifosize) 742 pio_count = port->fifosize; 743 744 if (!dma->chan || dma_count < dma_min) 745 msm_handle_tx_pio(port, pio_count); 746 else 747 err = msm_handle_tx_dma(msm_port, dma_count); 748 749 if (err) /* fall back to PIO mode */ 750 msm_handle_tx_pio(port, pio_count); 751} 752 753static void msm_handle_delta_cts(struct uart_port *port) 754{ 755 msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR); 756 port->icount.cts++; 757 wake_up_interruptible(&port->state->port.delta_msr_wait); 758} 759 760static irqreturn_t msm_uart_irq(int irq, void *dev_id) 761{ 762 struct uart_port *port = dev_id; 763 struct msm_port *msm_port = UART_TO_MSM(port); 764 struct msm_dma *dma = &msm_port->rx_dma; 765 unsigned long flags; 766 unsigned int misr; 767 u32 val; 768 769 spin_lock_irqsave(&port->lock, flags); 770 misr = msm_read(port, UART_MISR); 771 msm_write(port, 0, UART_IMR); /* disable interrupt */ 772 773 if (misr & UART_IMR_RXBREAK_START) { 774 msm_port->break_detected = true; 775 msm_write(port, UART_CR_CMD_RESET_RXBREAK_START, UART_CR); 776 } 777 778 if (misr & (UART_IMR_RXLEV | UART_IMR_RXSTALE)) { 779 if (dma->count) { 780 val = UART_CR_CMD_STALE_EVENT_DISABLE; 781 msm_write(port, val, UART_CR); 782 val = UART_CR_CMD_RESET_STALE_INT; 783 msm_write(port, val, UART_CR); 784 /* 785 * Flush DMA input fifo to memory, this will also 786 * trigger DMA RX completion 787 */ 788 dmaengine_terminate_all(dma->chan); 789 } else if (msm_port->is_uartdm) { 790 msm_handle_rx_dm(port, misr); 791 } else { 792 msm_handle_rx(port); 793 } 794 } 795 if (misr & UART_IMR_TXLEV) 796 msm_handle_tx(port); 797 if (misr & UART_IMR_DELTA_CTS) 798 msm_handle_delta_cts(port); 799 800 msm_write(port, msm_port->imr, UART_IMR); /* restore interrupt */ 801 spin_unlock_irqrestore(&port->lock, flags); 802 803 return IRQ_HANDLED; 804} 805 806static unsigned int msm_tx_empty(struct uart_port *port) 807{ 808 return (msm_read(port, UART_SR) & UART_SR_TX_EMPTY) ? TIOCSER_TEMT : 0; 809} 810 811static unsigned int msm_get_mctrl(struct uart_port *port) 812{ 813 return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR | TIOCM_RTS; 814} 815 816static void msm_reset(struct uart_port *port) 817{ 818 struct msm_port *msm_port = UART_TO_MSM(port); 819 820 /* reset everything */ 821 msm_write(port, UART_CR_CMD_RESET_RX, UART_CR); 822 msm_write(port, UART_CR_CMD_RESET_TX, UART_CR); 823 msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR); 824 msm_write(port, UART_CR_CMD_RESET_BREAK_INT, UART_CR); 825 msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR); 826 msm_write(port, UART_CR_CMD_SET_RFR, UART_CR); 827 828 /* Disable DM modes */ 829 if (msm_port->is_uartdm) 830 msm_write(port, 0, UARTDM_DMEN); 831} 832 833static void msm_set_mctrl(struct uart_port *port, unsigned int mctrl) 834{ 835 unsigned int mr; 836 837 mr = msm_read(port, UART_MR1); 838 839 if (!(mctrl & TIOCM_RTS)) { 840 mr &= ~UART_MR1_RX_RDY_CTL; 841 msm_write(port, mr, UART_MR1); 842 msm_write(port, UART_CR_CMD_RESET_RFR, UART_CR); 843 } else { 844 mr |= UART_MR1_RX_RDY_CTL; 845 msm_write(port, mr, UART_MR1); 846 } 847} 848 849static void msm_break_ctl(struct uart_port *port, int break_ctl) 850{ 851 if (break_ctl) 852 msm_write(port, UART_CR_CMD_START_BREAK, UART_CR); 853 else 854 msm_write(port, UART_CR_CMD_STOP_BREAK, UART_CR); 855} 856 857struct msm_baud_map { 858 u16 divisor; 859 u8 code; 860 u8 rxstale; 861}; 862 863static const struct msm_baud_map * 864msm_find_best_baud(struct uart_port *port, unsigned int baud) 865{ 866 unsigned int i, divisor; 867 const struct msm_baud_map *entry; 868 static const struct msm_baud_map table[] = { 869 { 1536, 0x00, 1 }, 870 { 768, 0x11, 1 }, 871 { 384, 0x22, 1 }, 872 { 192, 0x33, 1 }, 873 { 96, 0x44, 1 }, 874 { 48, 0x55, 1 }, 875 { 32, 0x66, 1 }, 876 { 24, 0x77, 1 }, 877 { 16, 0x88, 1 }, 878 { 12, 0x99, 6 }, 879 { 8, 0xaa, 6 }, 880 { 6, 0xbb, 6 }, 881 { 4, 0xcc, 6 }, 882 { 3, 0xdd, 8 }, 883 { 2, 0xee, 16 }, 884 { 1, 0xff, 31 }, 885 { 0, 0xff, 31 }, 886 }; 887 888 divisor = uart_get_divisor(port, baud); 889 890 for (i = 0, entry = table; i < ARRAY_SIZE(table); i++, entry++) 891 if (entry->divisor <= divisor) 892 break; 893 894 return entry; /* Default to smallest divider */ 895} 896 897static int msm_set_baud_rate(struct uart_port *port, unsigned int baud, 898 unsigned long *saved_flags) 899{ 900 unsigned int rxstale, watermark, mask; 901 struct msm_port *msm_port = UART_TO_MSM(port); 902 const struct msm_baud_map *entry; 903 unsigned long flags; 904 905 entry = msm_find_best_baud(port, baud); 906 907 msm_write(port, entry->code, UART_CSR); 908 909 if (baud > 460800) 910 port->uartclk = baud * 16; 911 912 flags = *saved_flags; 913 spin_unlock_irqrestore(&port->lock, flags); 914 915 clk_set_rate(msm_port->clk, port->uartclk); 916 917 spin_lock_irqsave(&port->lock, flags); 918 *saved_flags = flags; 919 920 /* RX stale watermark */ 921 rxstale = entry->rxstale; 922 watermark = UART_IPR_STALE_LSB & rxstale; 923 if (msm_port->is_uartdm) { 924 mask = UART_DM_IPR_STALE_TIMEOUT_MSB; 925 } else { 926 watermark |= UART_IPR_RXSTALE_LAST; 927 mask = UART_IPR_STALE_TIMEOUT_MSB; 928 } 929 930 watermark |= mask & (rxstale << 2); 931 932 msm_write(port, watermark, UART_IPR); 933 934 /* set RX watermark */ 935 watermark = (port->fifosize * 3) / 4; 936 msm_write(port, watermark, UART_RFWR); 937 938 /* set TX watermark */ 939 msm_write(port, 10, UART_TFWR); 940 941 msm_write(port, UART_CR_CMD_PROTECTION_EN, UART_CR); 942 msm_reset(port); 943 944 /* Enable RX and TX */ 945 msm_write(port, UART_CR_TX_ENABLE | UART_CR_RX_ENABLE, UART_CR); 946 947 /* turn on RX and CTS interrupts */ 948 msm_port->imr = UART_IMR_RXLEV | UART_IMR_RXSTALE | 949 UART_IMR_CURRENT_CTS | UART_IMR_RXBREAK_START; 950 951 msm_write(port, msm_port->imr, UART_IMR); 952 953 if (msm_port->is_uartdm) { 954 msm_write(port, UART_CR_CMD_RESET_STALE_INT, UART_CR); 955 msm_write(port, 0xFFFFFF, UARTDM_DMRX); 956 msm_write(port, UART_CR_CMD_STALE_EVENT_ENABLE, UART_CR); 957 } 958 959 return baud; 960} 961 962static void msm_init_clock(struct uart_port *port) 963{ 964 struct msm_port *msm_port = UART_TO_MSM(port); 965 966 clk_prepare_enable(msm_port->clk); 967 clk_prepare_enable(msm_port->pclk); 968 msm_serial_set_mnd_regs(port); 969} 970 971static int msm_startup(struct uart_port *port) 972{ 973 struct msm_port *msm_port = UART_TO_MSM(port); 974 unsigned int data, rfr_level, mask; 975 int ret; 976 977 snprintf(msm_port->name, sizeof(msm_port->name), 978 "msm_serial%d", port->line); 979 980 ret = request_irq(port->irq, msm_uart_irq, IRQF_TRIGGER_HIGH, 981 msm_port->name, port); 982 if (unlikely(ret)) 983 return ret; 984 985 msm_init_clock(port); 986 987 if (likely(port->fifosize > 12)) 988 rfr_level = port->fifosize - 12; 989 else 990 rfr_level = port->fifosize; 991 992 /* set automatic RFR level */ 993 data = msm_read(port, UART_MR1); 994 995 if (msm_port->is_uartdm) 996 mask = UART_DM_MR1_AUTO_RFR_LEVEL1; 997 else 998 mask = UART_MR1_AUTO_RFR_LEVEL1; 999 1000 data &= ~mask; 1001 data &= ~UART_MR1_AUTO_RFR_LEVEL0; 1002 data |= mask & (rfr_level << 2); 1003 data |= UART_MR1_AUTO_RFR_LEVEL0 & rfr_level; 1004 msm_write(port, data, UART_MR1); 1005 1006 if (msm_port->is_uartdm) { 1007 msm_request_tx_dma(msm_port, msm_port->uart.mapbase); 1008 msm_request_rx_dma(msm_port, msm_port->uart.mapbase); 1009 } 1010 1011 return 0; 1012} 1013 1014static void msm_shutdown(struct uart_port *port) 1015{ 1016 struct msm_port *msm_port = UART_TO_MSM(port); 1017 1018 msm_port->imr = 0; 1019 msm_write(port, 0, UART_IMR); /* disable interrupts */ 1020 1021 if (msm_port->is_uartdm) 1022 msm_release_dma(msm_port); 1023 1024 clk_disable_unprepare(msm_port->clk); 1025 1026 free_irq(port->irq, port); 1027} 1028 1029static void msm_set_termios(struct uart_port *port, struct ktermios *termios, 1030 struct ktermios *old) 1031{ 1032 struct msm_port *msm_port = UART_TO_MSM(port); 1033 struct msm_dma *dma = &msm_port->rx_dma; 1034 unsigned long flags; 1035 unsigned int baud, mr; 1036 1037 spin_lock_irqsave(&port->lock, flags); 1038 1039 if (dma->chan) /* Terminate if any */ 1040 msm_stop_dma(port, dma); 1041 1042 /* calculate and set baud rate */ 1043 baud = uart_get_baud_rate(port, termios, old, 300, 4000000); 1044 baud = msm_set_baud_rate(port, baud, &flags); 1045 if (tty_termios_baud_rate(termios)) 1046 tty_termios_encode_baud_rate(termios, baud, baud); 1047 1048 /* calculate parity */ 1049 mr = msm_read(port, UART_MR2); 1050 mr &= ~UART_MR2_PARITY_MODE; 1051 if (termios->c_cflag & PARENB) { 1052 if (termios->c_cflag & PARODD) 1053 mr |= UART_MR2_PARITY_MODE_ODD; 1054 else if (termios->c_cflag & CMSPAR) 1055 mr |= UART_MR2_PARITY_MODE_SPACE; 1056 else 1057 mr |= UART_MR2_PARITY_MODE_EVEN; 1058 } 1059 1060 /* calculate bits per char */ 1061 mr &= ~UART_MR2_BITS_PER_CHAR; 1062 switch (termios->c_cflag & CSIZE) { 1063 case CS5: 1064 mr |= UART_MR2_BITS_PER_CHAR_5; 1065 break; 1066 case CS6: 1067 mr |= UART_MR2_BITS_PER_CHAR_6; 1068 break; 1069 case CS7: 1070 mr |= UART_MR2_BITS_PER_CHAR_7; 1071 break; 1072 case CS8: 1073 default: 1074 mr |= UART_MR2_BITS_PER_CHAR_8; 1075 break; 1076 } 1077 1078 /* calculate stop bits */ 1079 mr &= ~(UART_MR2_STOP_BIT_LEN_ONE | UART_MR2_STOP_BIT_LEN_TWO); 1080 if (termios->c_cflag & CSTOPB) 1081 mr |= UART_MR2_STOP_BIT_LEN_TWO; 1082 else 1083 mr |= UART_MR2_STOP_BIT_LEN_ONE; 1084 1085 /* set parity, bits per char, and stop bit */ 1086 msm_write(port, mr, UART_MR2); 1087 1088 /* calculate and set hardware flow control */ 1089 mr = msm_read(port, UART_MR1); 1090 mr &= ~(UART_MR1_CTS_CTL | UART_MR1_RX_RDY_CTL); 1091 if (termios->c_cflag & CRTSCTS) { 1092 mr |= UART_MR1_CTS_CTL; 1093 mr |= UART_MR1_RX_RDY_CTL; 1094 } 1095 msm_write(port, mr, UART_MR1); 1096 1097 /* Configure status bits to ignore based on termio flags. */ 1098 port->read_status_mask = 0; 1099 if (termios->c_iflag & INPCK) 1100 port->read_status_mask |= UART_SR_PAR_FRAME_ERR; 1101 if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) 1102 port->read_status_mask |= UART_SR_RX_BREAK; 1103 1104 uart_update_timeout(port, termios->c_cflag, baud); 1105 1106 /* Try to use DMA */ 1107 msm_start_rx_dma(msm_port); 1108 1109 spin_unlock_irqrestore(&port->lock, flags); 1110} 1111 1112static const char *msm_type(struct uart_port *port) 1113{ 1114 return "MSM"; 1115} 1116 1117static void msm_release_port(struct uart_port *port) 1118{ 1119 struct platform_device *pdev = to_platform_device(port->dev); 1120 struct resource *uart_resource; 1121 resource_size_t size; 1122 1123 uart_resource = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1124 if (unlikely(!uart_resource)) 1125 return; 1126 size = resource_size(uart_resource); 1127 1128 release_mem_region(port->mapbase, size); 1129 iounmap(port->membase); 1130 port->membase = NULL; 1131} 1132 1133static int msm_request_port(struct uart_port *port) 1134{ 1135 struct platform_device *pdev = to_platform_device(port->dev); 1136 struct resource *uart_resource; 1137 resource_size_t size; 1138 int ret; 1139 1140 uart_resource = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1141 if (unlikely(!uart_resource)) 1142 return -ENXIO; 1143 1144 size = resource_size(uart_resource); 1145 1146 if (!request_mem_region(port->mapbase, size, "msm_serial")) 1147 return -EBUSY; 1148 1149 port->membase = ioremap(port->mapbase, size); 1150 if (!port->membase) { 1151 ret = -EBUSY; 1152 goto fail_release_port; 1153 } 1154 1155 return 0; 1156 1157fail_release_port: 1158 release_mem_region(port->mapbase, size); 1159 return ret; 1160} 1161 1162static void msm_config_port(struct uart_port *port, int flags) 1163{ 1164 int ret; 1165 1166 if (flags & UART_CONFIG_TYPE) { 1167 port->type = PORT_MSM; 1168 ret = msm_request_port(port); 1169 if (ret) 1170 return; 1171 } 1172} 1173 1174static int msm_verify_port(struct uart_port *port, struct serial_struct *ser) 1175{ 1176 if (unlikely(ser->type != PORT_UNKNOWN && ser->type != PORT_MSM)) 1177 return -EINVAL; 1178 if (unlikely(port->irq != ser->irq)) 1179 return -EINVAL; 1180 return 0; 1181} 1182 1183static void msm_power(struct uart_port *port, unsigned int state, 1184 unsigned int oldstate) 1185{ 1186 struct msm_port *msm_port = UART_TO_MSM(port); 1187 1188 switch (state) { 1189 case 0: 1190 clk_prepare_enable(msm_port->clk); 1191 clk_prepare_enable(msm_port->pclk); 1192 break; 1193 case 3: 1194 clk_disable_unprepare(msm_port->clk); 1195 clk_disable_unprepare(msm_port->pclk); 1196 break; 1197 default: 1198 pr_err("msm_serial: Unknown PM state %d\n", state); 1199 } 1200} 1201 1202#ifdef CONFIG_CONSOLE_POLL 1203static int msm_poll_get_char_single(struct uart_port *port) 1204{ 1205 struct msm_port *msm_port = UART_TO_MSM(port); 1206 unsigned int rf_reg = msm_port->is_uartdm ? UARTDM_RF : UART_RF; 1207 1208 if (!(msm_read(port, UART_SR) & UART_SR_RX_READY)) 1209 return NO_POLL_CHAR; 1210 1211 return msm_read(port, rf_reg) & 0xff; 1212} 1213 1214static int msm_poll_get_char_dm(struct uart_port *port) 1215{ 1216 int c; 1217 static u32 slop; 1218 static int count; 1219 unsigned char *sp = (unsigned char *)&slop; 1220 1221 /* Check if a previous read had more than one char */ 1222 if (count) { 1223 c = sp[sizeof(slop) - count]; 1224 count--; 1225 /* Or if FIFO is empty */ 1226 } else if (!(msm_read(port, UART_SR) & UART_SR_RX_READY)) { 1227 /* 1228 * If RX packing buffer has less than a word, force stale to 1229 * push contents into RX FIFO 1230 */ 1231 count = msm_read(port, UARTDM_RXFS); 1232 count = (count >> UARTDM_RXFS_BUF_SHIFT) & UARTDM_RXFS_BUF_MASK; 1233 if (count) { 1234 msm_write(port, UART_CR_CMD_FORCE_STALE, UART_CR); 1235 slop = msm_read(port, UARTDM_RF); 1236 c = sp[0]; 1237 count--; 1238 msm_write(port, UART_CR_CMD_RESET_STALE_INT, UART_CR); 1239 msm_write(port, 0xFFFFFF, UARTDM_DMRX); 1240 msm_write(port, UART_CR_CMD_STALE_EVENT_ENABLE, 1241 UART_CR); 1242 } else { 1243 c = NO_POLL_CHAR; 1244 } 1245 /* FIFO has a word */ 1246 } else { 1247 slop = msm_read(port, UARTDM_RF); 1248 c = sp[0]; 1249 count = sizeof(slop) - 1; 1250 } 1251 1252 return c; 1253} 1254 1255static int msm_poll_get_char(struct uart_port *port) 1256{ 1257 u32 imr; 1258 int c; 1259 struct msm_port *msm_port = UART_TO_MSM(port); 1260 1261 /* Disable all interrupts */ 1262 imr = msm_read(port, UART_IMR); 1263 msm_write(port, 0, UART_IMR); 1264 1265 if (msm_port->is_uartdm) 1266 c = msm_poll_get_char_dm(port); 1267 else 1268 c = msm_poll_get_char_single(port); 1269 1270 /* Enable interrupts */ 1271 msm_write(port, imr, UART_IMR); 1272 1273 return c; 1274} 1275 1276static void msm_poll_put_char(struct uart_port *port, unsigned char c) 1277{ 1278 u32 imr; 1279 struct msm_port *msm_port = UART_TO_MSM(port); 1280 1281 /* Disable all interrupts */ 1282 imr = msm_read(port, UART_IMR); 1283 msm_write(port, 0, UART_IMR); 1284 1285 if (msm_port->is_uartdm) 1286 msm_reset_dm_count(port, 1); 1287 1288 /* Wait until FIFO is empty */ 1289 while (!(msm_read(port, UART_SR) & UART_SR_TX_READY)) 1290 cpu_relax(); 1291 1292 /* Write a character */ 1293 msm_write(port, c, msm_port->is_uartdm ? UARTDM_TF : UART_TF); 1294 1295 /* Wait until FIFO is empty */ 1296 while (!(msm_read(port, UART_SR) & UART_SR_TX_READY)) 1297 cpu_relax(); 1298 1299 /* Enable interrupts */ 1300 msm_write(port, imr, UART_IMR); 1301} 1302#endif 1303 1304static struct uart_ops msm_uart_pops = { 1305 .tx_empty = msm_tx_empty, 1306 .set_mctrl = msm_set_mctrl, 1307 .get_mctrl = msm_get_mctrl, 1308 .stop_tx = msm_stop_tx, 1309 .start_tx = msm_start_tx, 1310 .stop_rx = msm_stop_rx, 1311 .enable_ms = msm_enable_ms, 1312 .break_ctl = msm_break_ctl, 1313 .startup = msm_startup, 1314 .shutdown = msm_shutdown, 1315 .set_termios = msm_set_termios, 1316 .type = msm_type, 1317 .release_port = msm_release_port, 1318 .request_port = msm_request_port, 1319 .config_port = msm_config_port, 1320 .verify_port = msm_verify_port, 1321 .pm = msm_power, 1322#ifdef CONFIG_CONSOLE_POLL 1323 .poll_get_char = msm_poll_get_char, 1324 .poll_put_char = msm_poll_put_char, 1325#endif 1326}; 1327 1328static struct msm_port msm_uart_ports[] = { 1329 { 1330 .uart = { 1331 .iotype = UPIO_MEM, 1332 .ops = &msm_uart_pops, 1333 .flags = UPF_BOOT_AUTOCONF, 1334 .fifosize = 64, 1335 .line = 0, 1336 }, 1337 }, 1338 { 1339 .uart = { 1340 .iotype = UPIO_MEM, 1341 .ops = &msm_uart_pops, 1342 .flags = UPF_BOOT_AUTOCONF, 1343 .fifosize = 64, 1344 .line = 1, 1345 }, 1346 }, 1347 { 1348 .uart = { 1349 .iotype = UPIO_MEM, 1350 .ops = &msm_uart_pops, 1351 .flags = UPF_BOOT_AUTOCONF, 1352 .fifosize = 64, 1353 .line = 2, 1354 }, 1355 }, 1356}; 1357 1358#define UART_NR ARRAY_SIZE(msm_uart_ports) 1359 1360static inline struct uart_port *msm_get_port_from_line(unsigned int line) 1361{ 1362 return &msm_uart_ports[line].uart; 1363} 1364 1365#ifdef CONFIG_SERIAL_MSM_CONSOLE 1366static void __msm_console_write(struct uart_port *port, const char *s, 1367 unsigned int count, bool is_uartdm) 1368{ 1369 int i; 1370 int num_newlines = 0; 1371 bool replaced = false; 1372 void __iomem *tf; 1373 1374 if (is_uartdm) 1375 tf = port->membase + UARTDM_TF; 1376 else 1377 tf = port->membase + UART_TF; 1378 1379 /* Account for newlines that will get a carriage return added */ 1380 for (i = 0; i < count; i++) 1381 if (s[i] == '\n') 1382 num_newlines++; 1383 count += num_newlines; 1384 1385 spin_lock(&port->lock); 1386 if (is_uartdm) 1387 msm_reset_dm_count(port, count); 1388 1389 i = 0; 1390 while (i < count) { 1391 int j; 1392 unsigned int num_chars; 1393 char buf[4] = { 0 }; 1394 1395 if (is_uartdm) 1396 num_chars = min(count - i, (unsigned int)sizeof(buf)); 1397 else 1398 num_chars = 1; 1399 1400 for (j = 0; j < num_chars; j++) { 1401 char c = *s; 1402 1403 if (c == '\n' && !replaced) { 1404 buf[j] = '\r'; 1405 j++; 1406 replaced = true; 1407 } 1408 if (j < num_chars) { 1409 buf[j] = c; 1410 s++; 1411 replaced = false; 1412 } 1413 } 1414 1415 while (!(msm_read(port, UART_SR) & UART_SR_TX_READY)) 1416 cpu_relax(); 1417 1418 iowrite32_rep(tf, buf, 1); 1419 i += num_chars; 1420 } 1421 spin_unlock(&port->lock); 1422} 1423 1424static void msm_console_write(struct console *co, const char *s, 1425 unsigned int count) 1426{ 1427 struct uart_port *port; 1428 struct msm_port *msm_port; 1429 1430 BUG_ON(co->index < 0 || co->index >= UART_NR); 1431 1432 port = msm_get_port_from_line(co->index); 1433 msm_port = UART_TO_MSM(port); 1434 1435 __msm_console_write(port, s, count, msm_port->is_uartdm); 1436} 1437 1438static int __init msm_console_setup(struct console *co, char *options) 1439{ 1440 struct uart_port *port; 1441 int baud = 115200; 1442 int bits = 8; 1443 int parity = 'n'; 1444 int flow = 'n'; 1445 1446 if (unlikely(co->index >= UART_NR || co->index < 0)) 1447 return -ENXIO; 1448 1449 port = msm_get_port_from_line(co->index); 1450 1451 if (unlikely(!port->membase)) 1452 return -ENXIO; 1453 1454 msm_init_clock(port); 1455 1456 if (options) 1457 uart_parse_options(options, &baud, &parity, &bits, &flow); 1458 1459 pr_info("msm_serial: console setup on port #%d\n", port->line); 1460 1461 return uart_set_options(port, co, baud, parity, bits, flow); 1462} 1463 1464static void 1465msm_serial_early_write(struct console *con, const char *s, unsigned n) 1466{ 1467 struct earlycon_device *dev = con->data; 1468 1469 __msm_console_write(&dev->port, s, n, false); 1470} 1471 1472static int __init 1473msm_serial_early_console_setup(struct earlycon_device *device, const char *opt) 1474{ 1475 if (!device->port.membase) 1476 return -ENODEV; 1477 1478 device->con->write = msm_serial_early_write; 1479 return 0; 1480} 1481EARLYCON_DECLARE(msm_serial, msm_serial_early_console_setup); 1482OF_EARLYCON_DECLARE(msm_serial, "qcom,msm-uart", 1483 msm_serial_early_console_setup); 1484 1485static void 1486msm_serial_early_write_dm(struct console *con, const char *s, unsigned n) 1487{ 1488 struct earlycon_device *dev = con->data; 1489 1490 __msm_console_write(&dev->port, s, n, true); 1491} 1492 1493static int __init 1494msm_serial_early_console_setup_dm(struct earlycon_device *device, 1495 const char *opt) 1496{ 1497 if (!device->port.membase) 1498 return -ENODEV; 1499 1500 device->con->write = msm_serial_early_write_dm; 1501 return 0; 1502} 1503EARLYCON_DECLARE(msm_serial_dm, msm_serial_early_console_setup_dm); 1504OF_EARLYCON_DECLARE(msm_serial_dm, "qcom,msm-uartdm", 1505 msm_serial_early_console_setup_dm); 1506 1507static struct uart_driver msm_uart_driver; 1508 1509static struct console msm_console = { 1510 .name = "ttyMSM", 1511 .write = msm_console_write, 1512 .device = uart_console_device, 1513 .setup = msm_console_setup, 1514 .flags = CON_PRINTBUFFER, 1515 .index = -1, 1516 .data = &msm_uart_driver, 1517}; 1518 1519#define MSM_CONSOLE (&msm_console) 1520 1521#else 1522#define MSM_CONSOLE NULL 1523#endif 1524 1525static struct uart_driver msm_uart_driver = { 1526 .owner = THIS_MODULE, 1527 .driver_name = "msm_serial", 1528 .dev_name = "ttyMSM", 1529 .nr = UART_NR, 1530 .cons = MSM_CONSOLE, 1531}; 1532 1533static atomic_t msm_uart_next_id = ATOMIC_INIT(0); 1534 1535static const struct of_device_id msm_uartdm_table[] = { 1536 { .compatible = "qcom,msm-uartdm-v1.1", .data = (void *)UARTDM_1P1 }, 1537 { .compatible = "qcom,msm-uartdm-v1.2", .data = (void *)UARTDM_1P2 }, 1538 { .compatible = "qcom,msm-uartdm-v1.3", .data = (void *)UARTDM_1P3 }, 1539 { .compatible = "qcom,msm-uartdm-v1.4", .data = (void *)UARTDM_1P4 }, 1540 { } 1541}; 1542 1543static int msm_serial_probe(struct platform_device *pdev) 1544{ 1545 struct msm_port *msm_port; 1546 struct resource *resource; 1547 struct uart_port *port; 1548 const struct of_device_id *id; 1549 int irq, line; 1550 1551 if (pdev->dev.of_node) 1552 line = of_alias_get_id(pdev->dev.of_node, "serial"); 1553 else 1554 line = pdev->id; 1555 1556 if (line < 0) 1557 line = atomic_inc_return(&msm_uart_next_id) - 1; 1558 1559 if (unlikely(line < 0 || line >= UART_NR)) 1560 return -ENXIO; 1561 1562 dev_info(&pdev->dev, "msm_serial: detected port #%d\n", line); 1563 1564 port = msm_get_port_from_line(line); 1565 port->dev = &pdev->dev; 1566 msm_port = UART_TO_MSM(port); 1567 1568 id = of_match_device(msm_uartdm_table, &pdev->dev); 1569 if (id) 1570 msm_port->is_uartdm = (unsigned long)id->data; 1571 else 1572 msm_port->is_uartdm = 0; 1573 1574 msm_port->clk = devm_clk_get(&pdev->dev, "core"); 1575 if (IS_ERR(msm_port->clk)) 1576 return PTR_ERR(msm_port->clk); 1577 1578 if (msm_port->is_uartdm) { 1579 msm_port->pclk = devm_clk_get(&pdev->dev, "iface"); 1580 if (IS_ERR(msm_port->pclk)) 1581 return PTR_ERR(msm_port->pclk); 1582 1583 clk_set_rate(msm_port->clk, 1843200); 1584 } 1585 1586 port->uartclk = clk_get_rate(msm_port->clk); 1587 dev_info(&pdev->dev, "uartclk = %d\n", port->uartclk); 1588 1589 resource = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1590 if (unlikely(!resource)) 1591 return -ENXIO; 1592 port->mapbase = resource->start; 1593 1594 irq = platform_get_irq(pdev, 0); 1595 if (unlikely(irq < 0)) 1596 return -ENXIO; 1597 port->irq = irq; 1598 1599 platform_set_drvdata(pdev, port); 1600 1601 return uart_add_one_port(&msm_uart_driver, port); 1602} 1603 1604static int msm_serial_remove(struct platform_device *pdev) 1605{ 1606 struct uart_port *port = platform_get_drvdata(pdev); 1607 1608 uart_remove_one_port(&msm_uart_driver, port); 1609 1610 return 0; 1611} 1612 1613static const struct of_device_id msm_match_table[] = { 1614 { .compatible = "qcom,msm-uart" }, 1615 { .compatible = "qcom,msm-uartdm" }, 1616 {} 1617}; 1618 1619static struct platform_driver msm_platform_driver = { 1620 .remove = msm_serial_remove, 1621 .probe = msm_serial_probe, 1622 .driver = { 1623 .name = "msm_serial", 1624 .of_match_table = msm_match_table, 1625 }, 1626}; 1627 1628static int __init msm_serial_init(void) 1629{ 1630 int ret; 1631 1632 ret = uart_register_driver(&msm_uart_driver); 1633 if (unlikely(ret)) 1634 return ret; 1635 1636 ret = platform_driver_register(&msm_platform_driver); 1637 if (unlikely(ret)) 1638 uart_unregister_driver(&msm_uart_driver); 1639 1640 pr_info("msm_serial: driver initialized\n"); 1641 1642 return ret; 1643} 1644 1645static void __exit msm_serial_exit(void) 1646{ 1647 platform_driver_unregister(&msm_platform_driver); 1648 uart_unregister_driver(&msm_uart_driver); 1649} 1650 1651module_init(msm_serial_init); 1652module_exit(msm_serial_exit); 1653 1654MODULE_AUTHOR("Robert Love <rlove@google.com>"); 1655MODULE_DESCRIPTION("Driver for msm7x serial device"); 1656MODULE_LICENSE("GPL"); 1657