1/* 2 * Copyright (C) 2014 Broadcom Corporation 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation version 2. 7 * 8 * This program is distributed "as is" WITHOUT ANY WARRANTY of any 9 * kind, whether express or implied; without even the implied warranty 10 * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 11 * GNU General Public License for more details. 12 */ 13 14#include <linux/delay.h> 15#include <linux/i2c.h> 16#include <linux/interrupt.h> 17#include <linux/io.h> 18#include <linux/kernel.h> 19#include <linux/module.h> 20#include <linux/platform_device.h> 21#include <linux/slab.h> 22 23#define CFG_OFFSET 0x00 24#define CFG_RESET_SHIFT 31 25#define CFG_EN_SHIFT 30 26#define CFG_M_RETRY_CNT_SHIFT 16 27#define CFG_M_RETRY_CNT_MASK 0x0f 28 29#define TIM_CFG_OFFSET 0x04 30#define TIM_CFG_MODE_400_SHIFT 31 31 32#define M_FIFO_CTRL_OFFSET 0x0c 33#define M_FIFO_RX_FLUSH_SHIFT 31 34#define M_FIFO_TX_FLUSH_SHIFT 30 35#define M_FIFO_RX_CNT_SHIFT 16 36#define M_FIFO_RX_CNT_MASK 0x7f 37#define M_FIFO_RX_THLD_SHIFT 8 38#define M_FIFO_RX_THLD_MASK 0x3f 39 40#define M_CMD_OFFSET 0x30 41#define M_CMD_START_BUSY_SHIFT 31 42#define M_CMD_STATUS_SHIFT 25 43#define M_CMD_STATUS_MASK 0x07 44#define M_CMD_STATUS_SUCCESS 0x0 45#define M_CMD_STATUS_LOST_ARB 0x1 46#define M_CMD_STATUS_NACK_ADDR 0x2 47#define M_CMD_STATUS_NACK_DATA 0x3 48#define M_CMD_STATUS_TIMEOUT 0x4 49#define M_CMD_PROTOCOL_SHIFT 9 50#define M_CMD_PROTOCOL_MASK 0xf 51#define M_CMD_PROTOCOL_BLK_WR 0x7 52#define M_CMD_PROTOCOL_BLK_RD 0x8 53#define M_CMD_PEC_SHIFT 8 54#define M_CMD_RD_CNT_SHIFT 0 55#define M_CMD_RD_CNT_MASK 0xff 56 57#define IE_OFFSET 0x38 58#define IE_M_RX_FIFO_FULL_SHIFT 31 59#define IE_M_RX_THLD_SHIFT 30 60#define IE_M_START_BUSY_SHIFT 28 61 62#define IS_OFFSET 0x3c 63#define IS_M_RX_FIFO_FULL_SHIFT 31 64#define IS_M_RX_THLD_SHIFT 30 65#define IS_M_START_BUSY_SHIFT 28 66 67#define M_TX_OFFSET 0x40 68#define M_TX_WR_STATUS_SHIFT 31 69#define M_TX_DATA_SHIFT 0 70#define M_TX_DATA_MASK 0xff 71 72#define M_RX_OFFSET 0x44 73#define M_RX_STATUS_SHIFT 30 74#define M_RX_STATUS_MASK 0x03 75#define M_RX_PEC_ERR_SHIFT 29 76#define M_RX_DATA_SHIFT 0 77#define M_RX_DATA_MASK 0xff 78 79#define I2C_TIMEOUT_MESC 100 80#define M_TX_RX_FIFO_SIZE 64 81 82enum bus_speed_index { 83 I2C_SPD_100K = 0, 84 I2C_SPD_400K, 85}; 86 87struct bcm_iproc_i2c_dev { 88 struct device *device; 89 int irq; 90 91 void __iomem *base; 92 93 struct i2c_adapter adapter; 94 unsigned int bus_speed; 95 96 struct completion done; 97 int xfer_is_done; 98}; 99 100/* 101 * Can be expanded in the future if more interrupt status bits are utilized 102 */ 103#define ISR_MASK (1 << IS_M_START_BUSY_SHIFT) 104 105static irqreturn_t bcm_iproc_i2c_isr(int irq, void *data) 106{ 107 struct bcm_iproc_i2c_dev *iproc_i2c = data; 108 u32 status = readl(iproc_i2c->base + IS_OFFSET); 109 110 status &= ISR_MASK; 111 112 if (!status) 113 return IRQ_NONE; 114 115 writel(status, iproc_i2c->base + IS_OFFSET); 116 iproc_i2c->xfer_is_done = 1; 117 complete_all(&iproc_i2c->done); 118 119 return IRQ_HANDLED; 120} 121 122static int bcm_iproc_i2c_check_status(struct bcm_iproc_i2c_dev *iproc_i2c, 123 struct i2c_msg *msg) 124{ 125 u32 val; 126 127 val = readl(iproc_i2c->base + M_CMD_OFFSET); 128 val = (val >> M_CMD_STATUS_SHIFT) & M_CMD_STATUS_MASK; 129 130 switch (val) { 131 case M_CMD_STATUS_SUCCESS: 132 return 0; 133 134 case M_CMD_STATUS_LOST_ARB: 135 dev_dbg(iproc_i2c->device, "lost bus arbitration\n"); 136 return -EAGAIN; 137 138 case M_CMD_STATUS_NACK_ADDR: 139 dev_dbg(iproc_i2c->device, "NAK addr:0x%02x\n", msg->addr); 140 return -ENXIO; 141 142 case M_CMD_STATUS_NACK_DATA: 143 dev_dbg(iproc_i2c->device, "NAK data\n"); 144 return -ENXIO; 145 146 case M_CMD_STATUS_TIMEOUT: 147 dev_dbg(iproc_i2c->device, "bus timeout\n"); 148 return -ETIMEDOUT; 149 150 default: 151 dev_dbg(iproc_i2c->device, "unknown error code=%d\n", val); 152 return -EIO; 153 } 154} 155 156static int bcm_iproc_i2c_xfer_single_msg(struct bcm_iproc_i2c_dev *iproc_i2c, 157 struct i2c_msg *msg) 158{ 159 int ret, i; 160 u8 addr; 161 u32 val; 162 unsigned long time_left = msecs_to_jiffies(I2C_TIMEOUT_MESC); 163 164 /* check if bus is busy */ 165 if (!!(readl(iproc_i2c->base + M_CMD_OFFSET) & 166 BIT(M_CMD_START_BUSY_SHIFT))) { 167 dev_warn(iproc_i2c->device, "bus is busy\n"); 168 return -EBUSY; 169 } 170 171 /* format and load slave address into the TX FIFO */ 172 addr = msg->addr << 1 | (msg->flags & I2C_M_RD ? 1 : 0); 173 writel(addr, iproc_i2c->base + M_TX_OFFSET); 174 175 /* for a write transaction, load data into the TX FIFO */ 176 if (!(msg->flags & I2C_M_RD)) { 177 for (i = 0; i < msg->len; i++) { 178 val = msg->buf[i]; 179 180 /* mark the last byte */ 181 if (i == msg->len - 1) 182 val |= 1 << M_TX_WR_STATUS_SHIFT; 183 184 writel(val, iproc_i2c->base + M_TX_OFFSET); 185 } 186 } 187 188 /* mark as incomplete before starting the transaction */ 189 reinit_completion(&iproc_i2c->done); 190 iproc_i2c->xfer_is_done = 0; 191 192 /* 193 * Enable the "start busy" interrupt, which will be triggered after the 194 * transaction is done, i.e., the internal start_busy bit, transitions 195 * from 1 to 0. 196 */ 197 writel(1 << IE_M_START_BUSY_SHIFT, iproc_i2c->base + IE_OFFSET); 198 199 /* 200 * Now we can activate the transfer. For a read operation, specify the 201 * number of bytes to read 202 */ 203 val = 1 << M_CMD_START_BUSY_SHIFT; 204 if (msg->flags & I2C_M_RD) { 205 val |= (M_CMD_PROTOCOL_BLK_RD << M_CMD_PROTOCOL_SHIFT) | 206 (msg->len << M_CMD_RD_CNT_SHIFT); 207 } else { 208 val |= (M_CMD_PROTOCOL_BLK_WR << M_CMD_PROTOCOL_SHIFT); 209 } 210 writel(val, iproc_i2c->base + M_CMD_OFFSET); 211 212 time_left = wait_for_completion_timeout(&iproc_i2c->done, time_left); 213 214 /* disable all interrupts */ 215 writel(0, iproc_i2c->base + IE_OFFSET); 216 /* read it back to flush the write */ 217 readl(iproc_i2c->base + IE_OFFSET); 218 219 /* make sure the interrupt handler isn't running */ 220 synchronize_irq(iproc_i2c->irq); 221 222 if (!time_left && !iproc_i2c->xfer_is_done) { 223 dev_err(iproc_i2c->device, "transaction timed out\n"); 224 225 /* flush FIFOs */ 226 val = (1 << M_FIFO_RX_FLUSH_SHIFT) | 227 (1 << M_FIFO_TX_FLUSH_SHIFT); 228 writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET); 229 return -ETIMEDOUT; 230 } 231 232 ret = bcm_iproc_i2c_check_status(iproc_i2c, msg); 233 if (ret) { 234 /* flush both TX/RX FIFOs */ 235 val = (1 << M_FIFO_RX_FLUSH_SHIFT) | 236 (1 << M_FIFO_TX_FLUSH_SHIFT); 237 writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET); 238 return ret; 239 } 240 241 /* 242 * For a read operation, we now need to load the data from FIFO 243 * into the memory buffer 244 */ 245 if (msg->flags & I2C_M_RD) { 246 for (i = 0; i < msg->len; i++) { 247 msg->buf[i] = (readl(iproc_i2c->base + M_RX_OFFSET) >> 248 M_RX_DATA_SHIFT) & M_RX_DATA_MASK; 249 } 250 } 251 252 return 0; 253} 254 255static int bcm_iproc_i2c_xfer(struct i2c_adapter *adapter, 256 struct i2c_msg msgs[], int num) 257{ 258 struct bcm_iproc_i2c_dev *iproc_i2c = i2c_get_adapdata(adapter); 259 int ret, i; 260 261 /* go through all messages */ 262 for (i = 0; i < num; i++) { 263 ret = bcm_iproc_i2c_xfer_single_msg(iproc_i2c, &msgs[i]); 264 if (ret) { 265 dev_dbg(iproc_i2c->device, "xfer failed\n"); 266 return ret; 267 } 268 } 269 270 return num; 271} 272 273static uint32_t bcm_iproc_i2c_functionality(struct i2c_adapter *adap) 274{ 275 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; 276} 277 278static const struct i2c_algorithm bcm_iproc_algo = { 279 .master_xfer = bcm_iproc_i2c_xfer, 280 .functionality = bcm_iproc_i2c_functionality, 281}; 282 283static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = { 284 /* need to reserve one byte in the FIFO for the slave address */ 285 .max_read_len = M_TX_RX_FIFO_SIZE - 1, 286 .max_write_len = M_TX_RX_FIFO_SIZE - 1, 287}; 288 289static int bcm_iproc_i2c_cfg_speed(struct bcm_iproc_i2c_dev *iproc_i2c) 290{ 291 unsigned int bus_speed; 292 u32 val; 293 int ret = of_property_read_u32(iproc_i2c->device->of_node, 294 "clock-frequency", &bus_speed); 295 if (ret < 0) { 296 dev_info(iproc_i2c->device, 297 "unable to interpret clock-frequency DT property\n"); 298 bus_speed = 100000; 299 } 300 301 if (bus_speed < 100000) { 302 dev_err(iproc_i2c->device, "%d Hz bus speed not supported\n", 303 bus_speed); 304 dev_err(iproc_i2c->device, 305 "valid speeds are 100khz and 400khz\n"); 306 return -EINVAL; 307 } else if (bus_speed < 400000) { 308 bus_speed = 100000; 309 } else { 310 bus_speed = 400000; 311 } 312 313 iproc_i2c->bus_speed = bus_speed; 314 val = readl(iproc_i2c->base + TIM_CFG_OFFSET); 315 val &= ~(1 << TIM_CFG_MODE_400_SHIFT); 316 val |= (bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT; 317 writel(val, iproc_i2c->base + TIM_CFG_OFFSET); 318 319 dev_info(iproc_i2c->device, "bus set to %u Hz\n", bus_speed); 320 321 return 0; 322} 323 324static int bcm_iproc_i2c_init(struct bcm_iproc_i2c_dev *iproc_i2c) 325{ 326 u32 val; 327 328 /* put controller in reset */ 329 val = readl(iproc_i2c->base + CFG_OFFSET); 330 val |= 1 << CFG_RESET_SHIFT; 331 val &= ~(1 << CFG_EN_SHIFT); 332 writel(val, iproc_i2c->base + CFG_OFFSET); 333 334 /* wait 100 usec per spec */ 335 udelay(100); 336 337 /* bring controller out of reset */ 338 val &= ~(1 << CFG_RESET_SHIFT); 339 writel(val, iproc_i2c->base + CFG_OFFSET); 340 341 /* flush TX/RX FIFOs and set RX FIFO threshold to zero */ 342 val = (1 << M_FIFO_RX_FLUSH_SHIFT) | (1 << M_FIFO_TX_FLUSH_SHIFT); 343 writel(val, iproc_i2c->base + M_FIFO_CTRL_OFFSET); 344 345 /* disable all interrupts */ 346 writel(0, iproc_i2c->base + IE_OFFSET); 347 348 /* clear all pending interrupts */ 349 writel(0xffffffff, iproc_i2c->base + IS_OFFSET); 350 351 return 0; 352} 353 354static void bcm_iproc_i2c_enable_disable(struct bcm_iproc_i2c_dev *iproc_i2c, 355 bool enable) 356{ 357 u32 val; 358 359 val = readl(iproc_i2c->base + CFG_OFFSET); 360 if (enable) 361 val |= BIT(CFG_EN_SHIFT); 362 else 363 val &= ~BIT(CFG_EN_SHIFT); 364 writel(val, iproc_i2c->base + CFG_OFFSET); 365} 366 367static int bcm_iproc_i2c_probe(struct platform_device *pdev) 368{ 369 int irq, ret = 0; 370 struct bcm_iproc_i2c_dev *iproc_i2c; 371 struct i2c_adapter *adap; 372 struct resource *res; 373 374 iproc_i2c = devm_kzalloc(&pdev->dev, sizeof(*iproc_i2c), 375 GFP_KERNEL); 376 if (!iproc_i2c) 377 return -ENOMEM; 378 379 platform_set_drvdata(pdev, iproc_i2c); 380 iproc_i2c->device = &pdev->dev; 381 init_completion(&iproc_i2c->done); 382 383 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 384 iproc_i2c->base = devm_ioremap_resource(iproc_i2c->device, res); 385 if (IS_ERR(iproc_i2c->base)) 386 return PTR_ERR(iproc_i2c->base); 387 388 ret = bcm_iproc_i2c_init(iproc_i2c); 389 if (ret) 390 return ret; 391 392 ret = bcm_iproc_i2c_cfg_speed(iproc_i2c); 393 if (ret) 394 return ret; 395 396 irq = platform_get_irq(pdev, 0); 397 if (irq <= 0) { 398 dev_err(iproc_i2c->device, "no irq resource\n"); 399 return irq; 400 } 401 iproc_i2c->irq = irq; 402 403 ret = devm_request_irq(iproc_i2c->device, irq, bcm_iproc_i2c_isr, 0, 404 pdev->name, iproc_i2c); 405 if (ret < 0) { 406 dev_err(iproc_i2c->device, "unable to request irq %i\n", irq); 407 return ret; 408 } 409 410 bcm_iproc_i2c_enable_disable(iproc_i2c, true); 411 412 adap = &iproc_i2c->adapter; 413 i2c_set_adapdata(adap, iproc_i2c); 414 strlcpy(adap->name, "Broadcom iProc I2C adapter", sizeof(adap->name)); 415 adap->algo = &bcm_iproc_algo; 416 adap->quirks = &bcm_iproc_i2c_quirks; 417 adap->dev.parent = &pdev->dev; 418 adap->dev.of_node = pdev->dev.of_node; 419 420 ret = i2c_add_adapter(adap); 421 if (ret) { 422 dev_err(iproc_i2c->device, "failed to add adapter\n"); 423 return ret; 424 } 425 426 return 0; 427} 428 429static int bcm_iproc_i2c_remove(struct platform_device *pdev) 430{ 431 struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev); 432 433 /* make sure there's no pending interrupt when we remove the adapter */ 434 writel(0, iproc_i2c->base + IE_OFFSET); 435 readl(iproc_i2c->base + IE_OFFSET); 436 synchronize_irq(iproc_i2c->irq); 437 438 i2c_del_adapter(&iproc_i2c->adapter); 439 bcm_iproc_i2c_enable_disable(iproc_i2c, false); 440 441 return 0; 442} 443 444#ifdef CONFIG_PM_SLEEP 445 446static int bcm_iproc_i2c_suspend(struct device *dev) 447{ 448 struct platform_device *pdev = to_platform_device(dev); 449 struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev); 450 451 /* make sure there's no pending interrupt when we go into suspend */ 452 writel(0, iproc_i2c->base + IE_OFFSET); 453 readl(iproc_i2c->base + IE_OFFSET); 454 synchronize_irq(iproc_i2c->irq); 455 456 /* now disable the controller */ 457 bcm_iproc_i2c_enable_disable(iproc_i2c, false); 458 459 return 0; 460} 461 462static int bcm_iproc_i2c_resume(struct device *dev) 463{ 464 struct platform_device *pdev = to_platform_device(dev); 465 struct bcm_iproc_i2c_dev *iproc_i2c = platform_get_drvdata(pdev); 466 int ret; 467 u32 val; 468 469 /* 470 * Power domain could have been shut off completely in system deep 471 * sleep, so re-initialize the block here 472 */ 473 ret = bcm_iproc_i2c_init(iproc_i2c); 474 if (ret) 475 return ret; 476 477 /* configure to the desired bus speed */ 478 val = readl(iproc_i2c->base + TIM_CFG_OFFSET); 479 val &= ~(1 << TIM_CFG_MODE_400_SHIFT); 480 val |= (iproc_i2c->bus_speed == 400000) << TIM_CFG_MODE_400_SHIFT; 481 writel(val, iproc_i2c->base + TIM_CFG_OFFSET); 482 483 bcm_iproc_i2c_enable_disable(iproc_i2c, true); 484 485 return 0; 486} 487 488static const struct dev_pm_ops bcm_iproc_i2c_pm_ops = { 489 .suspend_late = &bcm_iproc_i2c_suspend, 490 .resume_early = &bcm_iproc_i2c_resume 491}; 492 493#define BCM_IPROC_I2C_PM_OPS (&bcm_iproc_i2c_pm_ops) 494#else 495#define BCM_IPROC_I2C_PM_OPS NULL 496#endif /* CONFIG_PM_SLEEP */ 497 498static const struct of_device_id bcm_iproc_i2c_of_match[] = { 499 { .compatible = "brcm,iproc-i2c" }, 500 { /* sentinel */ } 501}; 502MODULE_DEVICE_TABLE(of, bcm_iproc_i2c_of_match); 503 504static struct platform_driver bcm_iproc_i2c_driver = { 505 .driver = { 506 .name = "bcm-iproc-i2c", 507 .of_match_table = bcm_iproc_i2c_of_match, 508 .pm = BCM_IPROC_I2C_PM_OPS, 509 }, 510 .probe = bcm_iproc_i2c_probe, 511 .remove = bcm_iproc_i2c_remove, 512}; 513module_platform_driver(bcm_iproc_i2c_driver); 514 515MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>"); 516MODULE_DESCRIPTION("Broadcom iProc I2C Driver"); 517MODULE_LICENSE("GPL v2"); 518