1/* 2 * AXS101/AXS103 Software Development Platform 3 * 4 * Copyright (C) 2013-15 Synopsys, Inc. (www.synopsys.com) 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 * 10 * This program is distributed in the hope that it will be useful, 11 * but WITHOUT ANY WARRANTY; without even the implied warranty of 12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 * GNU General Public License for more details. 14 * 15 */ 16 17#include <linux/of_platform.h> 18 19#include <asm/asm-offsets.h> 20#include <asm/clk.h> 21#include <asm/io.h> 22#include <asm/mach_desc.h> 23#include <asm/mcip.h> 24 25#define AXS_MB_CGU 0xE0010000 26#define AXS_MB_CREG 0xE0011000 27 28#define CREG_MB_IRQ_MUX (AXS_MB_CREG + 0x214) 29#define CREG_MB_SW_RESET (AXS_MB_CREG + 0x220) 30#define CREG_MB_VER (AXS_MB_CREG + 0x230) 31#define CREG_MB_CONFIG (AXS_MB_CREG + 0x234) 32 33#define AXC001_CREG 0xF0001000 34#define AXC001_GPIO_INTC 0xF0003000 35 36static void __init axs10x_enable_gpio_intc_wire(void) 37{ 38 /* 39 * Peripherals on CPU Card and Mother Board are wired to cpu intc via 40 * intermediate DW APB GPIO blocks (mainly for debouncing) 41 * 42 * --------------------- 43 * | snps,arc700-intc | 44 * --------------------- 45 * | #7 | #15 46 * ------------------- ------------------- 47 * | snps,dw-apb-gpio | | snps,dw-apb-gpio | 48 * ------------------- ------------------- 49 * | #12 | 50 * | [ Debug UART on cpu card ] 51 * | 52 * ------------------------ 53 * | snps,dw-apb-intc (MB)| 54 * ------------------------ 55 * | | | | 56 * [eth] [uart] [... other perip on Main Board] 57 * 58 * Current implementation of "irq-dw-apb-ictl" driver doesn't work well 59 * with stacked INTCs. In particular problem happens if its master INTC 60 * not yet instantiated. See discussion here - 61 * https://lkml.org/lkml/2015/3/4/755 62 * 63 * So setup the first gpio block as a passive pass thru and hide it from 64 * DT hardware topology - connect MB intc directly to cpu intc 65 * The GPIO "wire" needs to be init nevertheless (here) 66 * 67 * One side adv is that peripheral interrupt handling avoids one nested 68 * intc ISR hop 69 */ 70#define GPIO_INTEN (AXC001_GPIO_INTC + 0x30) 71#define GPIO_INTMASK (AXC001_GPIO_INTC + 0x34) 72#define GPIO_INTTYPE_LEVEL (AXC001_GPIO_INTC + 0x38) 73#define GPIO_INT_POLARITY (AXC001_GPIO_INTC + 0x3c) 74#define MB_TO_GPIO_IRQ 12 75 76 iowrite32(~(1 << MB_TO_GPIO_IRQ), (void __iomem *) GPIO_INTMASK); 77 iowrite32(0, (void __iomem *) GPIO_INTTYPE_LEVEL); 78 iowrite32(~0, (void __iomem *) GPIO_INT_POLARITY); 79 iowrite32(1 << MB_TO_GPIO_IRQ, (void __iomem *) GPIO_INTEN); 80} 81 82static inline void __init 83write_cgu_reg(uint32_t value, void __iomem *reg, void __iomem *lock_reg) 84{ 85 unsigned int loops = 128 * 1024, ctr; 86 87 iowrite32(value, reg); 88 89 ctr = loops; 90 while (((ioread32(lock_reg) & 1) == 1) && ctr--) /* wait for unlock */ 91 cpu_relax(); 92 93 ctr = loops; 94 while (((ioread32(lock_reg) & 1) == 0) && ctr--) /* wait for re-lock */ 95 cpu_relax(); 96} 97 98static void __init axs10x_print_board_ver(unsigned int creg, const char *str) 99{ 100 union ver { 101 struct { 102#ifdef CONFIG_CPU_BIG_ENDIAN 103 unsigned int pad:11, y:12, m:4, d:5; 104#else 105 unsigned int d:5, m:4, y:12, pad:11; 106#endif 107 }; 108 unsigned int val; 109 } board; 110 111 board.val = ioread32((void __iomem *)creg); 112 pr_info("AXS: %s FPGA Date: %u-%u-%u\n", str, board.d, board.m, 113 board.y); 114} 115 116static void __init axs10x_early_init(void) 117{ 118 int mb_rev; 119 char mb[32]; 120 121 /* Determine motherboard version */ 122 if (ioread32((void __iomem *) CREG_MB_CONFIG) & (1 << 28)) 123 mb_rev = 3; /* HT-3 (rev3.0) */ 124 else 125 mb_rev = 2; /* HT-2 (rev2.0) */ 126 127 axs10x_enable_gpio_intc_wire(); 128 129 scnprintf(mb, 32, "MainBoard v%d", mb_rev); 130 axs10x_print_board_ver(CREG_MB_VER, mb); 131} 132 133#ifdef CONFIG_AXS101 134 135#define CREG_CPU_ADDR_770 (AXC001_CREG + 0x20) 136#define CREG_CPU_ADDR_TUNN (AXC001_CREG + 0x60) 137#define CREG_CPU_ADDR_770_UPD (AXC001_CREG + 0x34) 138#define CREG_CPU_ADDR_TUNN_UPD (AXC001_CREG + 0x74) 139 140#define CREG_CPU_ARC770_IRQ_MUX (AXC001_CREG + 0x114) 141#define CREG_CPU_GPIO_UART_MUX (AXC001_CREG + 0x120) 142 143/* 144 * Set up System Memory Map for ARC cpu / peripherals controllers 145 * 146 * Each AXI master has a 4GB memory map specified as 16 apertures of 256MB, each 147 * of which maps to a corresponding 256MB aperture in Target slave memory map. 148 * 149 * e.g. ARC cpu AXI Master's aperture 8 (0x8000_0000) is mapped to aperture 0 150 * (0x0000_0000) of DDR Port 0 (slave #1) 151 * 152 * Access from cpu to MB controllers such as GMAC is setup using AXI Tunnel: 153 * which has master/slaves on both ends. 154 * e.g. aperture 14 (0xE000_0000) of ARC cpu is mapped to aperture 14 155 * (0xE000_0000) of CPU Card AXI Tunnel slave (slave #3) which is mapped to 156 * MB AXI Tunnel Master, which also has a mem map setup 157 * 158 * In the reverse direction, MB AXI Masters (e.g. GMAC) mem map is setup 159 * to map to MB AXI Tunnel slave which connects to CPU Card AXI Tunnel Master 160 */ 161struct aperture { 162 unsigned int slave_sel:4, slave_off:4, pad:24; 163}; 164 165/* CPU Card target slaves */ 166#define AXC001_SLV_NONE 0 167#define AXC001_SLV_DDR_PORT0 1 168#define AXC001_SLV_SRAM 2 169#define AXC001_SLV_AXI_TUNNEL 3 170#define AXC001_SLV_AXI2APB 6 171#define AXC001_SLV_DDR_PORT1 7 172 173/* MB AXI Target slaves */ 174#define AXS_MB_SLV_NONE 0 175#define AXS_MB_SLV_AXI_TUNNEL_CPU 1 176#define AXS_MB_SLV_AXI_TUNNEL_HAPS 2 177#define AXS_MB_SLV_SRAM 3 178#define AXS_MB_SLV_CONTROL 4 179 180/* MB AXI masters */ 181#define AXS_MB_MST_TUNNEL_CPU 0 182#define AXS_MB_MST_USB_OHCI 10 183 184/* 185 * memmap for ARC core on CPU Card 186 */ 187static const struct aperture axc001_memmap[16] = { 188 {AXC001_SLV_AXI_TUNNEL, 0x0}, 189 {AXC001_SLV_AXI_TUNNEL, 0x1}, 190 {AXC001_SLV_SRAM, 0x0}, /* 0x2000_0000: Local SRAM */ 191 {AXC001_SLV_NONE, 0x0}, 192 {AXC001_SLV_NONE, 0x0}, 193 {AXC001_SLV_NONE, 0x0}, 194 {AXC001_SLV_NONE, 0x0}, 195 {AXC001_SLV_NONE, 0x0}, 196 {AXC001_SLV_DDR_PORT0, 0x0}, /* 0x8000_0000: DDR 0..256M */ 197 {AXC001_SLV_DDR_PORT0, 0x1}, /* 0x9000_0000: DDR 256..512M */ 198 {AXC001_SLV_DDR_PORT0, 0x2}, 199 {AXC001_SLV_DDR_PORT0, 0x3}, 200 {AXC001_SLV_NONE, 0x0}, 201 {AXC001_SLV_AXI_TUNNEL, 0xD}, 202 {AXC001_SLV_AXI_TUNNEL, 0xE}, /* MB: CREG, CGU... */ 203 {AXC001_SLV_AXI2APB, 0x0}, /* CPU Card local CREG, CGU... */ 204}; 205 206/* 207 * memmap for CPU Card AXI Tunnel Master (for access by MB controllers) 208 * GMAC (MB) -> MB AXI Tunnel slave -> CPU Card AXI Tunnel Master -> DDR 209 */ 210static const struct aperture axc001_axi_tunnel_memmap[16] = { 211 {AXC001_SLV_AXI_TUNNEL, 0x0}, 212 {AXC001_SLV_AXI_TUNNEL, 0x1}, 213 {AXC001_SLV_SRAM, 0x0}, 214 {AXC001_SLV_NONE, 0x0}, 215 {AXC001_SLV_NONE, 0x0}, 216 {AXC001_SLV_NONE, 0x0}, 217 {AXC001_SLV_NONE, 0x0}, 218 {AXC001_SLV_NONE, 0x0}, 219 {AXC001_SLV_DDR_PORT1, 0x0}, 220 {AXC001_SLV_DDR_PORT1, 0x1}, 221 {AXC001_SLV_DDR_PORT1, 0x2}, 222 {AXC001_SLV_DDR_PORT1, 0x3}, 223 {AXC001_SLV_NONE, 0x0}, 224 {AXC001_SLV_AXI_TUNNEL, 0xD}, 225 {AXC001_SLV_AXI_TUNNEL, 0xE}, 226 {AXC001_SLV_AXI2APB, 0x0}, 227}; 228 229/* 230 * memmap for MB AXI Masters 231 * Same mem map for all perip controllers as well as MB AXI Tunnel Master 232 */ 233static const struct aperture axs_mb_memmap[16] = { 234 {AXS_MB_SLV_SRAM, 0x0}, 235 {AXS_MB_SLV_SRAM, 0x0}, 236 {AXS_MB_SLV_NONE, 0x0}, 237 {AXS_MB_SLV_NONE, 0x0}, 238 {AXS_MB_SLV_NONE, 0x0}, 239 {AXS_MB_SLV_NONE, 0x0}, 240 {AXS_MB_SLV_NONE, 0x0}, 241 {AXS_MB_SLV_NONE, 0x0}, 242 {AXS_MB_SLV_AXI_TUNNEL_CPU, 0x8}, /* DDR on CPU Card */ 243 {AXS_MB_SLV_AXI_TUNNEL_CPU, 0x9}, /* DDR on CPU Card */ 244 {AXS_MB_SLV_AXI_TUNNEL_CPU, 0xA}, 245 {AXS_MB_SLV_AXI_TUNNEL_CPU, 0xB}, 246 {AXS_MB_SLV_NONE, 0x0}, 247 {AXS_MB_SLV_AXI_TUNNEL_HAPS, 0xD}, 248 {AXS_MB_SLV_CONTROL, 0x0}, /* MB Local CREG, CGU... */ 249 {AXS_MB_SLV_AXI_TUNNEL_CPU, 0xF}, 250}; 251 252static noinline void __init 253axs101_set_memmap(void __iomem *base, const struct aperture map[16]) 254{ 255 unsigned int slave_select, slave_offset; 256 int i; 257 258 slave_select = slave_offset = 0; 259 for (i = 0; i < 8; i++) { 260 slave_select |= map[i].slave_sel << (i << 2); 261 slave_offset |= map[i].slave_off << (i << 2); 262 } 263 264 iowrite32(slave_select, base + 0x0); /* SLV0 */ 265 iowrite32(slave_offset, base + 0x8); /* OFFSET0 */ 266 267 slave_select = slave_offset = 0; 268 for (i = 0; i < 8; i++) { 269 slave_select |= map[i+8].slave_sel << (i << 2); 270 slave_offset |= map[i+8].slave_off << (i << 2); 271 } 272 273 iowrite32(slave_select, base + 0x4); /* SLV1 */ 274 iowrite32(slave_offset, base + 0xC); /* OFFSET1 */ 275} 276 277static void __init axs101_early_init(void) 278{ 279 int i; 280 281 /* ARC 770D memory view */ 282 axs101_set_memmap((void __iomem *) CREG_CPU_ADDR_770, axc001_memmap); 283 iowrite32(1, (void __iomem *) CREG_CPU_ADDR_770_UPD); 284 285 /* AXI tunnel memory map (incoming traffic from MB into CPU Card */ 286 axs101_set_memmap((void __iomem *) CREG_CPU_ADDR_TUNN, 287 axc001_axi_tunnel_memmap); 288 iowrite32(1, (void __iomem *) CREG_CPU_ADDR_TUNN_UPD); 289 290 /* MB peripherals memory map */ 291 for (i = AXS_MB_MST_TUNNEL_CPU; i <= AXS_MB_MST_USB_OHCI; i++) 292 axs101_set_memmap((void __iomem *) AXS_MB_CREG + (i << 4), 293 axs_mb_memmap); 294 295 iowrite32(0x3ff, (void __iomem *) AXS_MB_CREG + 0x100); /* Update */ 296 297 /* GPIO pins 18 and 19 are used as UART rx and tx, respectively. */ 298 iowrite32(0x01, (void __iomem *) CREG_CPU_GPIO_UART_MUX); 299 300 /* Set up the MB interrupt system: mux interrupts to GPIO7) */ 301 iowrite32(0x01, (void __iomem *) CREG_MB_IRQ_MUX); 302 303 /* reset ethernet and ULPI interfaces */ 304 iowrite32(0x18, (void __iomem *) CREG_MB_SW_RESET); 305 306 /* map GPIO 14:10 to ARC 9:5 (IRQ mux change for MB v2 onwards) */ 307 iowrite32(0x52, (void __iomem *) CREG_CPU_ARC770_IRQ_MUX); 308 309 axs10x_early_init(); 310} 311 312#endif /* CONFIG_AXS101 */ 313 314#ifdef CONFIG_AXS103 315 316#define AXC003_CGU 0xF0000000 317#define AXC003_CREG 0xF0001000 318#define AXC003_MST_AXI_TUNNEL 0 319#define AXC003_MST_HS38 1 320 321#define CREG_CPU_AXI_M0_IRQ_MUX (AXC003_CREG + 0x440) 322#define CREG_CPU_GPIO_UART_MUX (AXC003_CREG + 0x480) 323#define CREG_CPU_TUN_IO_CTRL (AXC003_CREG + 0x494) 324 325 326union pll_reg { 327 struct { 328#ifdef CONFIG_CPU_BIG_ENDIAN 329 unsigned int pad:17, noupd:1, bypass:1, edge:1, high:6, low:6; 330#else 331 unsigned int low:6, high:6, edge:1, bypass:1, noupd:1, pad:17; 332#endif 333 }; 334 unsigned int val; 335}; 336 337static unsigned int __init axs103_get_freq(void) 338{ 339 union pll_reg idiv, fbdiv, odiv; 340 unsigned int f = 33333333; 341 342 idiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 0); 343 fbdiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 4); 344 odiv.val = ioread32((void __iomem *)AXC003_CGU + 0x80 + 8); 345 346 if (idiv.bypass != 1) 347 f = f / (idiv.low + idiv.high); 348 349 if (fbdiv.bypass != 1) 350 f = f * (fbdiv.low + fbdiv.high); 351 352 if (odiv.bypass != 1) 353 f = f / (odiv.low + odiv.high); 354 355 f = (f + 500000) / 1000000; /* Rounding */ 356 return f; 357} 358 359static inline unsigned int __init encode_div(unsigned int id, int upd) 360{ 361 union pll_reg div; 362 363 div.val = 0; 364 365 div.noupd = !upd; 366 div.bypass = id == 1 ? 1 : 0; 367 div.edge = (id%2 == 0) ? 0 : 1; /* 0 = rising */ 368 div.low = (id%2 == 0) ? id >> 1 : (id >> 1)+1; 369 div.high = id >> 1; 370 371 return div.val; 372} 373 374noinline static void __init 375axs103_set_freq(unsigned int id, unsigned int fd, unsigned int od) 376{ 377 write_cgu_reg(encode_div(id, 0), 378 (void __iomem *)AXC003_CGU + 0x80 + 0, 379 (void __iomem *)AXC003_CGU + 0x110); 380 381 write_cgu_reg(encode_div(fd, 0), 382 (void __iomem *)AXC003_CGU + 0x80 + 4, 383 (void __iomem *)AXC003_CGU + 0x110); 384 385 write_cgu_reg(encode_div(od, 1), 386 (void __iomem *)AXC003_CGU + 0x80 + 8, 387 (void __iomem *)AXC003_CGU + 0x110); 388} 389 390static void __init axs103_early_init(void) 391{ 392 /* 393 * AXS103 configurations for SMP/QUAD configurations share device tree 394 * which defaults to 90 MHz. However recent failures of Quad config 395 * revealed P&R timing violations so clamp it down to safe 50 MHz 396 * Instead of duplicating defconfig/DT for SMP/QUAD, add a small hack 397 * 398 * This hack is really hacky as of now. Fix it properly by getting the 399 * number of cores as return value of platform's early SMP callback 400 */ 401#ifdef CONFIG_ARC_MCIP 402 unsigned int num_cores = (read_aux_reg(ARC_REG_MCIP_BCR) >> 16) & 0x3F; 403 if (num_cores > 2) 404 arc_set_core_freq(50 * 1000000); 405 else if (num_cores == 2) 406 arc_set_core_freq(75 * 1000000); 407#endif 408 409 switch (arc_get_core_freq()/1000000) { 410 case 33: 411 axs103_set_freq(1, 1, 1); 412 break; 413 case 50: 414 axs103_set_freq(1, 30, 20); 415 break; 416 case 75: 417 axs103_set_freq(2, 45, 10); 418 break; 419 case 90: 420 axs103_set_freq(2, 54, 10); 421 break; 422 case 100: 423 axs103_set_freq(1, 30, 10); 424 break; 425 case 125: 426 axs103_set_freq(2, 45, 6); 427 break; 428 default: 429 /* 430 * In this case, core_frequency derived from 431 * DT "clock-frequency" might not match with board value. 432 * Hence update it to match the board value. 433 */ 434 arc_set_core_freq(axs103_get_freq() * 1000000); 435 break; 436 } 437 438 pr_info("Freq is %dMHz\n", axs103_get_freq()); 439 440 /* Memory maps already config in pre-bootloader */ 441 442 /* set GPIO mux to UART */ 443 iowrite32(0x01, (void __iomem *) CREG_CPU_GPIO_UART_MUX); 444 445 iowrite32((0x00100000U | 0x000C0000U | 0x00003322U), 446 (void __iomem *) CREG_CPU_TUN_IO_CTRL); 447 448 /* Set up the AXS_MB interrupt system.*/ 449 iowrite32(12, (void __iomem *) (CREG_CPU_AXI_M0_IRQ_MUX 450 + (AXC003_MST_HS38 << 2))); 451 452 /* connect ICTL - Main Board with GPIO line */ 453 iowrite32(0x01, (void __iomem *) CREG_MB_IRQ_MUX); 454 455 axs10x_print_board_ver(AXC003_CREG + 4088, "AXC003 CPU Card"); 456 457 axs10x_early_init(); 458} 459#endif 460 461#ifdef CONFIG_AXS101 462 463static const char *axs101_compat[] __initconst = { 464 "snps,axs101", 465 NULL, 466}; 467 468MACHINE_START(AXS101, "axs101") 469 .dt_compat = axs101_compat, 470 .init_early = axs101_early_init, 471MACHINE_END 472 473#endif /* CONFIG_AXS101 */ 474 475#ifdef CONFIG_AXS103 476 477static const char *axs103_compat[] __initconst = { 478 "snps,axs103", 479 NULL, 480}; 481 482MACHINE_START(AXS103, "axs103") 483 .dt_compat = axs103_compat, 484 .init_early = axs103_early_init, 485MACHINE_END 486 487/* 488 * For the VDK OS-kit, to get the offset to pid and command fields 489 */ 490char coware_swa_pid_offset[TASK_PID]; 491char coware_swa_comm_offset[TASK_COMM]; 492 493#endif /* CONFIG_AXS103 */ 494