1/* 2 * Copyright ST-Ericsson 2012. 3 * 4 * Author: Arun Murthy <arun.murthy@stericsson.com> 5 * Licensed under GPLv2. 6 */ 7 8#ifndef _AB8500_BM_H 9#define _AB8500_BM_H 10 11#include <linux/kernel.h> 12#include <linux/mfd/abx500.h> 13 14/* 15 * System control 2 register offsets. 16 * bank = 0x02 17 */ 18#define AB8500_MAIN_WDOG_CTRL_REG 0x01 19#define AB8500_LOW_BAT_REG 0x03 20#define AB8500_BATT_OK_REG 0x04 21/* 22 * USB/ULPI register offsets 23 * Bank : 0x5 24 */ 25#define AB8500_USB_LINE_STAT_REG 0x80 26#define AB8500_USB_LINE_CTRL2_REG 0x82 27#define AB8500_USB_LINK1_STAT_REG 0x94 28 29/* 30 * Charger / status register offfsets 31 * Bank : 0x0B 32 */ 33#define AB8500_CH_STATUS1_REG 0x00 34#define AB8500_CH_STATUS2_REG 0x01 35#define AB8500_CH_USBCH_STAT1_REG 0x02 36#define AB8500_CH_USBCH_STAT2_REG 0x03 37#define AB8540_CH_USBCH_STAT3_REG 0x04 38#define AB8500_CH_STAT_REG 0x05 39 40/* 41 * Charger / control register offfsets 42 * Bank : 0x0B 43 */ 44#define AB8500_CH_VOLT_LVL_REG 0x40 45#define AB8500_CH_VOLT_LVL_MAX_REG 0x41 /*Only in Cut2.0*/ 46#define AB8500_CH_OPT_CRNTLVL_REG 0x42 47#define AB8500_CH_OPT_CRNTLVL_MAX_REG 0x43 /*Only in Cut2.0*/ 48#define AB8500_CH_WD_TIMER_REG 0x50 49#define AB8500_CHARG_WD_CTRL 0x51 50#define AB8500_BTEMP_HIGH_TH 0x52 51#define AB8500_LED_INDICATOR_PWM_CTRL 0x53 52#define AB8500_LED_INDICATOR_PWM_DUTY 0x54 53#define AB8500_BATT_OVV 0x55 54#define AB8500_CHARGER_CTRL 0x56 55#define AB8500_BAT_CTRL_CURRENT_SOURCE 0x60 /*Only in Cut2.0*/ 56 57/* 58 * Charger / main control register offsets 59 * Bank : 0x0B 60 */ 61#define AB8500_MCH_CTRL1 0x80 62#define AB8500_MCH_CTRL2 0x81 63#define AB8500_MCH_IPT_CURLVL_REG 0x82 64#define AB8500_CH_WD_REG 0x83 65 66/* 67 * Charger / USB control register offsets 68 * Bank : 0x0B 69 */ 70#define AB8500_USBCH_CTRL1_REG 0xC0 71#define AB8500_USBCH_CTRL2_REG 0xC1 72#define AB8500_USBCH_IPT_CRNTLVL_REG 0xC2 73#define AB8540_USB_PP_MODE_REG 0xC5 74#define AB8540_USB_PP_CHR_REG 0xC6 75 76/* 77 * Gas Gauge register offsets 78 * Bank : 0x0C 79 */ 80#define AB8500_GASG_CC_CTRL_REG 0x00 81#define AB8500_GASG_CC_ACCU1_REG 0x01 82#define AB8500_GASG_CC_ACCU2_REG 0x02 83#define AB8500_GASG_CC_ACCU3_REG 0x03 84#define AB8500_GASG_CC_ACCU4_REG 0x04 85#define AB8500_GASG_CC_SMPL_CNTRL_REG 0x05 86#define AB8500_GASG_CC_SMPL_CNTRH_REG 0x06 87#define AB8500_GASG_CC_SMPL_CNVL_REG 0x07 88#define AB8500_GASG_CC_SMPL_CNVH_REG 0x08 89#define AB8500_GASG_CC_CNTR_AVGOFF_REG 0x09 90#define AB8500_GASG_CC_OFFSET_REG 0x0A 91#define AB8500_GASG_CC_NCOV_ACCU 0x10 92#define AB8500_GASG_CC_NCOV_ACCU_CTRL 0x11 93#define AB8500_GASG_CC_NCOV_ACCU_LOW 0x12 94#define AB8500_GASG_CC_NCOV_ACCU_MED 0x13 95#define AB8500_GASG_CC_NCOV_ACCU_HIGH 0x14 96 97/* 98 * Interrupt register offsets 99 * Bank : 0x0E 100 */ 101#define AB8500_IT_SOURCE2_REG 0x01 102#define AB8500_IT_SOURCE21_REG 0x14 103 104/* 105 * RTC register offsets 106 * Bank: 0x0F 107 */ 108#define AB8500_RTC_BACKUP_CHG_REG 0x0C 109#define AB8500_RTC_CC_CONF_REG 0x01 110#define AB8500_RTC_CTRL_REG 0x0B 111#define AB8500_RTC_CTRL1_REG 0x11 112 113/* 114 * OTP register offsets 115 * Bank : 0x15 116 */ 117#define AB8500_OTP_CONF_15 0x0E 118 119/* GPADC constants from AB8500 spec, UM0836 */ 120#define ADC_RESOLUTION 1024 121#define ADC_CH_MAIN_MIN 0 122#define ADC_CH_MAIN_MAX 20030 123#define ADC_CH_VBUS_MIN 0 124#define ADC_CH_VBUS_MAX 20030 125#define ADC_CH_VBAT_MIN 2300 126#define ADC_CH_VBAT_MAX 4800 127#define ADC_CH_BKBAT_MIN 0 128#define ADC_CH_BKBAT_MAX 3200 129 130/* Main charge i/p current */ 131#define MAIN_CH_IP_CUR_0P9A 0x80 132#define MAIN_CH_IP_CUR_1P0A 0x90 133#define MAIN_CH_IP_CUR_1P1A 0xA0 134#define MAIN_CH_IP_CUR_1P2A 0xB0 135#define MAIN_CH_IP_CUR_1P3A 0xC0 136#define MAIN_CH_IP_CUR_1P4A 0xD0 137#define MAIN_CH_IP_CUR_1P5A 0xE0 138 139/* ChVoltLevel */ 140#define CH_VOL_LVL_3P5 0x00 141#define CH_VOL_LVL_4P0 0x14 142#define CH_VOL_LVL_4P05 0x16 143#define CH_VOL_LVL_4P1 0x1B 144#define CH_VOL_LVL_4P15 0x20 145#define CH_VOL_LVL_4P2 0x25 146#define CH_VOL_LVL_4P6 0x4D 147 148/* ChOutputCurrentLevel */ 149#define CH_OP_CUR_LVL_0P1 0x00 150#define CH_OP_CUR_LVL_0P2 0x01 151#define CH_OP_CUR_LVL_0P3 0x02 152#define CH_OP_CUR_LVL_0P4 0x03 153#define CH_OP_CUR_LVL_0P5 0x04 154#define CH_OP_CUR_LVL_0P6 0x05 155#define CH_OP_CUR_LVL_0P7 0x06 156#define CH_OP_CUR_LVL_0P8 0x07 157#define CH_OP_CUR_LVL_0P9 0x08 158#define CH_OP_CUR_LVL_1P4 0x0D 159#define CH_OP_CUR_LVL_1P5 0x0E 160#define CH_OP_CUR_LVL_1P6 0x0F 161#define CH_OP_CUR_LVL_2P 0x3F 162 163/* BTEMP High thermal limits */ 164#define BTEMP_HIGH_TH_57_0 0x00 165#define BTEMP_HIGH_TH_52 0x01 166#define BTEMP_HIGH_TH_57_1 0x02 167#define BTEMP_HIGH_TH_62 0x03 168 169/* current is mA */ 170#define USB_0P1A 100 171#define USB_0P2A 200 172#define USB_0P3A 300 173#define USB_0P4A 400 174#define USB_0P5A 500 175 176#define LOW_BAT_3P1V 0x20 177#define LOW_BAT_2P3V 0x00 178#define LOW_BAT_RESET 0x01 179#define LOW_BAT_ENABLE 0x01 180 181/* Backup battery constants */ 182#define BUP_ICH_SEL_50UA 0x00 183#define BUP_ICH_SEL_150UA 0x04 184#define BUP_ICH_SEL_300UA 0x08 185#define BUP_ICH_SEL_700UA 0x0C 186 187enum bup_vch_sel { 188 BUP_VCH_SEL_2P5V, 189 BUP_VCH_SEL_2P6V, 190 BUP_VCH_SEL_2P8V, 191 BUP_VCH_SEL_3P1V, 192 /* 193 * Note that the following 5 values 2.7v, 2.9v, 3.0v, 3.2v, 3.3v 194 * are only available on ab8540. You can't choose these 5 195 * voltage on ab8500/ab8505/ab9540. 196 */ 197 BUP_VCH_SEL_2P7V, 198 BUP_VCH_SEL_2P9V, 199 BUP_VCH_SEL_3P0V, 200 BUP_VCH_SEL_3P2V, 201 BUP_VCH_SEL_3P3V, 202}; 203 204#define BUP_VCH_RANGE 0x02 205#define VBUP33_VRTCN 0x01 206 207/* Battery OVV constants */ 208#define BATT_OVV_ENA 0x02 209#define BATT_OVV_TH_3P7 0x00 210#define BATT_OVV_TH_4P75 0x01 211 212/* A value to indicate over voltage */ 213#define BATT_OVV_VALUE 4750 214 215/* VBUS OVV constants */ 216#define VBUS_OVV_SELECT_MASK 0x78 217#define VBUS_OVV_SELECT_5P6V 0x00 218#define VBUS_OVV_SELECT_5P7V 0x08 219#define VBUS_OVV_SELECT_5P8V 0x10 220#define VBUS_OVV_SELECT_5P9V 0x18 221#define VBUS_OVV_SELECT_6P0V 0x20 222#define VBUS_OVV_SELECT_6P1V 0x28 223#define VBUS_OVV_SELECT_6P2V 0x30 224#define VBUS_OVV_SELECT_6P3V 0x38 225 226#define VBUS_AUTO_IN_CURR_LIM_ENA 0x04 227 228/* Fuel Gauge constants */ 229#define RESET_ACCU 0x02 230#define READ_REQ 0x01 231#define CC_DEEP_SLEEP_ENA 0x02 232#define CC_PWR_UP_ENA 0x01 233#define CC_SAMPLES_40 0x28 234#define RD_NCONV_ACCU_REQ 0x01 235#define CC_CALIB 0x08 236#define CC_INTAVGOFFSET_ENA 0x10 237#define CC_MUXOFFSET 0x80 238#define CC_INT_CAL_N_AVG_MASK 0x60 239#define CC_INT_CAL_SAMPLES_16 0x40 240#define CC_INT_CAL_SAMPLES_8 0x20 241#define CC_INT_CAL_SAMPLES_4 0x00 242 243/* RTC constants */ 244#define RTC_BUP_CH_ENA 0x10 245 246/* BatCtrl Current Source Constants */ 247#define BAT_CTRL_7U_ENA 0x01 248#define BAT_CTRL_20U_ENA 0x02 249#define BAT_CTRL_18U_ENA 0x01 250#define BAT_CTRL_16U_ENA 0x02 251#define BAT_CTRL_60U_ENA 0x01 252#define BAT_CTRL_120U_ENA 0x02 253#define BAT_CTRL_CMP_ENA 0x04 254#define FORCE_BAT_CTRL_CMP_HIGH 0x08 255#define BAT_CTRL_PULL_UP_ENA 0x10 256 257/* Battery type */ 258#define BATTERY_UNKNOWN 00 259 260/* Registers for pcut feature in ab8505 and ab9540 */ 261#define AB8505_RTC_PCUT_CTL_STATUS_REG 0x12 262#define AB8505_RTC_PCUT_TIME_REG 0x13 263#define AB8505_RTC_PCUT_MAX_TIME_REG 0x14 264#define AB8505_RTC_PCUT_FLAG_TIME_REG 0x15 265#define AB8505_RTC_PCUT_RESTART_REG 0x16 266#define AB8505_RTC_PCUT_DEBOUNCE_REG 0x17 267 268/* USB Power Path constants for ab8540 */ 269#define BUS_VSYS_VOL_SELECT_MASK 0x06 270#define BUS_VSYS_VOL_SELECT_3P6V 0x00 271#define BUS_VSYS_VOL_SELECT_3P325V 0x02 272#define BUS_VSYS_VOL_SELECT_3P9V 0x04 273#define BUS_VSYS_VOL_SELECT_4P3V 0x06 274#define BUS_POWER_PATH_MODE_ENA 0x01 275#define BUS_PP_PRECHG_CURRENT_MASK 0x0E 276#define BUS_POWER_PATH_PRECHG_ENA 0x01 277 278/** 279 * struct res_to_temp - defines one point in a temp to res curve. To 280 * be used in battery packs that combines the identification resistor with a 281 * NTC resistor. 282 * @temp: battery pack temperature in Celcius 283 * @resist: NTC resistor net total resistance 284 */ 285struct res_to_temp { 286 int temp; 287 int resist; 288}; 289 290/** 291 * struct batres_vs_temp - defines one point in a temp vs battery internal 292 * resistance curve. 293 * @temp: battery pack temperature in Celcius 294 * @resist: battery internal reistance in mOhm 295 */ 296struct batres_vs_temp { 297 int temp; 298 int resist; 299}; 300 301/* Forward declaration */ 302struct ab8500_fg; 303 304/** 305 * struct ab8500_fg_parameters - Fuel gauge algorithm parameters, in seconds 306 * if not specified 307 * @recovery_sleep_timer: Time between measurements while recovering 308 * @recovery_total_time: Total recovery time 309 * @init_timer: Measurement interval during startup 310 * @init_discard_time: Time we discard voltage measurement at startup 311 * @init_total_time: Total init time during startup 312 * @high_curr_time: Time current has to be high to go to recovery 313 * @accu_charging: FG accumulation time while charging 314 * @accu_high_curr: FG accumulation time in high current mode 315 * @high_curr_threshold: High current threshold, in mA 316 * @lowbat_threshold: Low battery threshold, in mV 317 * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 318 * Resolution in 50 mV step. 319 * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 320 * Resolution in 50 mV step. 321 * @user_cap_limit Capacity reported from user must be within this 322 * limit to be considered as sane, in percentage 323 * points. 324 * @maint_thres This is the threshold where we stop reporting 325 * battery full while in maintenance, in per cent 326 * @pcut_enable: Enable power cut feature in ab8505 327 * @pcut_max_time: Max time threshold 328 * @pcut_flag_time: Flagtime threshold 329 * @pcut_max_restart: Max number of restarts 330 * @pcut_debunce_time: Sets battery debounce time 331 */ 332struct ab8500_fg_parameters { 333 int recovery_sleep_timer; 334 int recovery_total_time; 335 int init_timer; 336 int init_discard_time; 337 int init_total_time; 338 int high_curr_time; 339 int accu_charging; 340 int accu_high_curr; 341 int high_curr_threshold; 342 int lowbat_threshold; 343 int battok_falling_th_sel0; 344 int battok_raising_th_sel1; 345 int user_cap_limit; 346 int maint_thres; 347 bool pcut_enable; 348 u8 pcut_max_time; 349 u8 pcut_flag_time; 350 u8 pcut_max_restart; 351 u8 pcut_debunce_time; 352}; 353 354/** 355 * struct ab8500_charger_maximization - struct used by the board config. 356 * @use_maxi: Enable maximization for this battery type 357 * @maxi_chg_curr: Maximum charger current allowed 358 * @maxi_wait_cycles: cycles to wait before setting charger current 359 * @charger_curr_step delta between two charger current settings (mA) 360 */ 361struct ab8500_maxim_parameters { 362 bool ena_maxi; 363 int chg_curr; 364 int wait_cycles; 365 int charger_curr_step; 366}; 367 368/** 369 * struct ab8500_bm_capacity_levels - ab8500 capacity level data 370 * @critical: critical capacity level in percent 371 * @low: low capacity level in percent 372 * @normal: normal capacity level in percent 373 * @high: high capacity level in percent 374 * @full: full capacity level in percent 375 */ 376struct ab8500_bm_capacity_levels { 377 int critical; 378 int low; 379 int normal; 380 int high; 381 int full; 382}; 383 384/** 385 * struct ab8500_bm_charger_parameters - Charger specific parameters 386 * @usb_volt_max: maximum allowed USB charger voltage in mV 387 * @usb_curr_max: maximum allowed USB charger current in mA 388 * @ac_volt_max: maximum allowed AC charger voltage in mV 389 * @ac_curr_max: maximum allowed AC charger current in mA 390 */ 391struct ab8500_bm_charger_parameters { 392 int usb_volt_max; 393 int usb_curr_max; 394 int ac_volt_max; 395 int ac_curr_max; 396}; 397 398/** 399 * struct ab8500_bm_data - ab8500 battery management data 400 * @temp_under under this temp, charging is stopped 401 * @temp_low between this temp and temp_under charging is reduced 402 * @temp_high between this temp and temp_over charging is reduced 403 * @temp_over over this temp, charging is stopped 404 * @temp_interval_chg temperature measurement interval in s when charging 405 * @temp_interval_nochg temperature measurement interval in s when not charging 406 * @main_safety_tmr_h safety timer for main charger 407 * @usb_safety_tmr_h safety timer for usb charger 408 * @bkup_bat_v voltage which we charge the backup battery with 409 * @bkup_bat_i current which we charge the backup battery with 410 * @no_maintenance indicates that maintenance charging is disabled 411 * @capacity_scaling indicates whether capacity scaling is to be used 412 * @adc_therm placement of thermistor, batctrl or battemp adc 413 * @chg_unknown_bat flag to enable charging of unknown batteries 414 * @enable_overshoot flag to enable VBAT overshoot control 415 * @fg_res resistance of FG resistor in 0.1mOhm 416 * @n_btypes number of elements in array bat_type 417 * @batt_id index of the identified battery in array bat_type 418 * @interval_charging charge alg cycle period time when charging (sec) 419 * @interval_not_charging charge alg cycle period time when not charging (sec) 420 * @temp_hysteresis temperature hysteresis 421 * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) 422 * @maxi: maximization parameters 423 * @cap_levels capacity in percent for the different capacity levels 424 * @bat_type table of supported battery types 425 * @chg_params charger parameters 426 * @fg_params fuel gauge parameters 427 */ 428struct ab8500_bm_data { 429 int temp_under; 430 int temp_low; 431 int temp_high; 432 int temp_over; 433 int temp_interval_chg; 434 int temp_interval_nochg; 435 int main_safety_tmr_h; 436 int usb_safety_tmr_h; 437 int bkup_bat_v; 438 int bkup_bat_i; 439 bool no_maintenance; 440 bool capacity_scaling; 441 bool chg_unknown_bat; 442 bool enable_overshoot; 443 enum abx500_adc_therm adc_therm; 444 int fg_res; 445 int n_btypes; 446 int batt_id; 447 int interval_charging; 448 int interval_not_charging; 449 int temp_hysteresis; 450 int gnd_lift_resistance; 451 const struct ab8500_maxim_parameters *maxi; 452 const struct ab8500_bm_capacity_levels *cap_levels; 453 const struct ab8500_bm_charger_parameters *chg_params; 454 const struct ab8500_fg_parameters *fg_params; 455}; 456 457struct ab8500_btemp; 458struct ab8500_gpadc; 459struct ab8500_fg; 460 461#ifdef CONFIG_AB8500_BM 462extern struct abx500_bm_data ab8500_bm_data; 463 464void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA); 465struct ab8500_btemp *ab8500_btemp_get(void); 466int ab8500_btemp_get_batctrl_temp(struct ab8500_btemp *btemp); 467int ab8500_btemp_get_temp(struct ab8500_btemp *btemp); 468struct ab8500_fg *ab8500_fg_get(void); 469int ab8500_fg_inst_curr_blocking(struct ab8500_fg *dev); 470int ab8500_fg_inst_curr_start(struct ab8500_fg *di); 471int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res); 472int ab8500_fg_inst_curr_started(struct ab8500_fg *di); 473int ab8500_fg_inst_curr_done(struct ab8500_fg *di); 474 475#else 476static struct abx500_bm_data ab8500_bm_data; 477#endif 478#endif /* _AB8500_BM_H */ 479