1/* 2 * Device driver for Microgate SyncLink GT serial adapters. 3 * 4 * written by Paul Fulghum for Microgate Corporation 5 * paulkf@microgate.com 6 * 7 * Microgate and SyncLink are trademarks of Microgate Corporation 8 * 9 * This code is released under the GNU General Public License (GPL) 10 * 11 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED 12 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 13 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 14 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, 15 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 16 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 17 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 18 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 19 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 20 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED 21 * OF THE POSSIBILITY OF SUCH DAMAGE. 22 */ 23 24/* 25 * DEBUG OUTPUT DEFINITIONS 26 * 27 * uncomment lines below to enable specific types of debug output 28 * 29 * DBGINFO information - most verbose output 30 * DBGERR serious errors 31 * DBGBH bottom half service routine debugging 32 * DBGISR interrupt service routine debugging 33 * DBGDATA output receive and transmit data 34 * DBGTBUF output transmit DMA buffers and registers 35 * DBGRBUF output receive DMA buffers and registers 36 */ 37 38#define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt 39#define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt 40#define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt 41#define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt 42#define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label)) 43/*#define DBGTBUF(info) dump_tbufs(info)*/ 44/*#define DBGRBUF(info) dump_rbufs(info)*/ 45 46 47#include <linux/module.h> 48#include <linux/errno.h> 49#include <linux/signal.h> 50#include <linux/sched.h> 51#include <linux/timer.h> 52#include <linux/interrupt.h> 53#include <linux/pci.h> 54#include <linux/tty.h> 55#include <linux/tty_flip.h> 56#include <linux/serial.h> 57#include <linux/major.h> 58#include <linux/string.h> 59#include <linux/fcntl.h> 60#include <linux/ptrace.h> 61#include <linux/ioport.h> 62#include <linux/mm.h> 63#include <linux/seq_file.h> 64#include <linux/slab.h> 65#include <linux/netdevice.h> 66#include <linux/vmalloc.h> 67#include <linux/init.h> 68#include <linux/delay.h> 69#include <linux/ioctl.h> 70#include <linux/termios.h> 71#include <linux/bitops.h> 72#include <linux/workqueue.h> 73#include <linux/hdlc.h> 74#include <linux/synclink.h> 75 76#include <asm/io.h> 77#include <asm/irq.h> 78#include <asm/dma.h> 79#include <asm/types.h> 80#include <asm/uaccess.h> 81 82#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE)) 83#define SYNCLINK_GENERIC_HDLC 1 84#else 85#define SYNCLINK_GENERIC_HDLC 0 86#endif 87 88/* 89 * module identification 90 */ 91static char *driver_name = "SyncLink GT"; 92static char *tty_driver_name = "synclink_gt"; 93static char *tty_dev_prefix = "ttySLG"; 94MODULE_LICENSE("GPL"); 95#define MGSL_MAGIC 0x5401 96#define MAX_DEVICES 32 97 98static struct pci_device_id pci_table[] = { 99 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 100 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 101 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 102 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,}, 103 {0,}, /* terminate list */ 104}; 105MODULE_DEVICE_TABLE(pci, pci_table); 106 107static int init_one(struct pci_dev *dev,const struct pci_device_id *ent); 108static void remove_one(struct pci_dev *dev); 109static struct pci_driver pci_driver = { 110 .name = "synclink_gt", 111 .id_table = pci_table, 112 .probe = init_one, 113 .remove = remove_one, 114}; 115 116static bool pci_registered; 117 118/* 119 * module configuration and status 120 */ 121static struct slgt_info *slgt_device_list; 122static int slgt_device_count; 123 124static int ttymajor; 125static int debug_level; 126static int maxframe[MAX_DEVICES]; 127 128module_param(ttymajor, int, 0); 129module_param(debug_level, int, 0); 130module_param_array(maxframe, int, NULL, 0); 131 132MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned"); 133MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail"); 134MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)"); 135 136/* 137 * tty support and callbacks 138 */ 139static struct tty_driver *serial_driver; 140 141static int open(struct tty_struct *tty, struct file * filp); 142static void close(struct tty_struct *tty, struct file * filp); 143static void hangup(struct tty_struct *tty); 144static void set_termios(struct tty_struct *tty, struct ktermios *old_termios); 145 146static int write(struct tty_struct *tty, const unsigned char *buf, int count); 147static int put_char(struct tty_struct *tty, unsigned char ch); 148static void send_xchar(struct tty_struct *tty, char ch); 149static void wait_until_sent(struct tty_struct *tty, int timeout); 150static int write_room(struct tty_struct *tty); 151static void flush_chars(struct tty_struct *tty); 152static void flush_buffer(struct tty_struct *tty); 153static void tx_hold(struct tty_struct *tty); 154static void tx_release(struct tty_struct *tty); 155 156static int ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg); 157static int chars_in_buffer(struct tty_struct *tty); 158static void throttle(struct tty_struct * tty); 159static void unthrottle(struct tty_struct * tty); 160static int set_break(struct tty_struct *tty, int break_state); 161 162/* 163 * generic HDLC support and callbacks 164 */ 165#if SYNCLINK_GENERIC_HDLC 166#define dev_to_port(D) (dev_to_hdlc(D)->priv) 167static void hdlcdev_tx_done(struct slgt_info *info); 168static void hdlcdev_rx(struct slgt_info *info, char *buf, int size); 169static int hdlcdev_init(struct slgt_info *info); 170static void hdlcdev_exit(struct slgt_info *info); 171#endif 172 173 174/* 175 * device specific structures, macros and functions 176 */ 177 178#define SLGT_MAX_PORTS 4 179#define SLGT_REG_SIZE 256 180 181/* 182 * conditional wait facility 183 */ 184struct cond_wait { 185 struct cond_wait *next; 186 wait_queue_head_t q; 187 wait_queue_t wait; 188 unsigned int data; 189}; 190static void init_cond_wait(struct cond_wait *w, unsigned int data); 191static void add_cond_wait(struct cond_wait **head, struct cond_wait *w); 192static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w); 193static void flush_cond_wait(struct cond_wait **head); 194 195/* 196 * DMA buffer descriptor and access macros 197 */ 198struct slgt_desc 199{ 200 __le16 count; 201 __le16 status; 202 __le32 pbuf; /* physical address of data buffer */ 203 __le32 next; /* physical address of next descriptor */ 204 205 /* driver book keeping */ 206 char *buf; /* virtual address of data buffer */ 207 unsigned int pdesc; /* physical address of this descriptor */ 208 dma_addr_t buf_dma_addr; 209 unsigned short buf_count; 210}; 211 212#define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b)) 213#define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b)) 214#define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b)) 215#define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0)) 216#define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b)) 217#define desc_count(a) (le16_to_cpu((a).count)) 218#define desc_status(a) (le16_to_cpu((a).status)) 219#define desc_complete(a) (le16_to_cpu((a).status) & BIT15) 220#define desc_eof(a) (le16_to_cpu((a).status) & BIT2) 221#define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1) 222#define desc_abort(a) (le16_to_cpu((a).status) & BIT0) 223#define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3) 224 225struct _input_signal_events { 226 int ri_up; 227 int ri_down; 228 int dsr_up; 229 int dsr_down; 230 int dcd_up; 231 int dcd_down; 232 int cts_up; 233 int cts_down; 234}; 235 236/* 237 * device instance data structure 238 */ 239struct slgt_info { 240 void *if_ptr; /* General purpose pointer (used by SPPP) */ 241 struct tty_port port; 242 243 struct slgt_info *next_device; /* device list link */ 244 245 int magic; 246 247 char device_name[25]; 248 struct pci_dev *pdev; 249 250 int port_count; /* count of ports on adapter */ 251 int adapter_num; /* adapter instance number */ 252 int port_num; /* port instance number */ 253 254 /* array of pointers to port contexts on this adapter */ 255 struct slgt_info *port_array[SLGT_MAX_PORTS]; 256 257 int line; /* tty line instance number */ 258 259 struct mgsl_icount icount; 260 261 int timeout; 262 int x_char; /* xon/xoff character */ 263 unsigned int read_status_mask; 264 unsigned int ignore_status_mask; 265 266 wait_queue_head_t status_event_wait_q; 267 wait_queue_head_t event_wait_q; 268 struct timer_list tx_timer; 269 struct timer_list rx_timer; 270 271 unsigned int gpio_present; 272 struct cond_wait *gpio_wait_q; 273 274 spinlock_t lock; /* spinlock for synchronizing with ISR */ 275 276 struct work_struct task; 277 u32 pending_bh; 278 bool bh_requested; 279 bool bh_running; 280 281 int isr_overflow; 282 bool irq_requested; /* true if IRQ requested */ 283 bool irq_occurred; /* for diagnostics use */ 284 285 /* device configuration */ 286 287 unsigned int bus_type; 288 unsigned int irq_level; 289 unsigned long irq_flags; 290 291 unsigned char __iomem * reg_addr; /* memory mapped registers address */ 292 u32 phys_reg_addr; 293 bool reg_addr_requested; 294 295 MGSL_PARAMS params; /* communications parameters */ 296 u32 idle_mode; 297 u32 max_frame_size; /* as set by device config */ 298 299 unsigned int rbuf_fill_level; 300 unsigned int rx_pio; 301 unsigned int if_mode; 302 unsigned int base_clock; 303 unsigned int xsync; 304 unsigned int xctrl; 305 306 /* device status */ 307 308 bool rx_enabled; 309 bool rx_restart; 310 311 bool tx_enabled; 312 bool tx_active; 313 314 unsigned char signals; /* serial signal states */ 315 int init_error; /* initialization error */ 316 317 unsigned char *tx_buf; 318 int tx_count; 319 320 char *flag_buf; 321 bool drop_rts_on_tx_done; 322 struct _input_signal_events input_signal_events; 323 324 int dcd_chkcount; /* check counts to prevent */ 325 int cts_chkcount; /* too many IRQs if a signal */ 326 int dsr_chkcount; /* is floating */ 327 int ri_chkcount; 328 329 char *bufs; /* virtual address of DMA buffer lists */ 330 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */ 331 332 unsigned int rbuf_count; 333 struct slgt_desc *rbufs; 334 unsigned int rbuf_current; 335 unsigned int rbuf_index; 336 unsigned int rbuf_fill_index; 337 unsigned short rbuf_fill_count; 338 339 unsigned int tbuf_count; 340 struct slgt_desc *tbufs; 341 unsigned int tbuf_current; 342 unsigned int tbuf_start; 343 344 unsigned char *tmp_rbuf; 345 unsigned int tmp_rbuf_count; 346 347 /* SPPP/Cisco HDLC device parts */ 348 349 int netcount; 350 spinlock_t netlock; 351#if SYNCLINK_GENERIC_HDLC 352 struct net_device *netdev; 353#endif 354 355}; 356 357static MGSL_PARAMS default_params = { 358 .mode = MGSL_MODE_HDLC, 359 .loopback = 0, 360 .flags = HDLC_FLAG_UNDERRUN_ABORT15, 361 .encoding = HDLC_ENCODING_NRZI_SPACE, 362 .clock_speed = 0, 363 .addr_filter = 0xff, 364 .crc_type = HDLC_CRC_16_CCITT, 365 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS, 366 .preamble = HDLC_PREAMBLE_PATTERN_NONE, 367 .data_rate = 9600, 368 .data_bits = 8, 369 .stop_bits = 1, 370 .parity = ASYNC_PARITY_NONE 371}; 372 373 374#define BH_RECEIVE 1 375#define BH_TRANSMIT 2 376#define BH_STATUS 4 377#define IO_PIN_SHUTDOWN_LIMIT 100 378 379#define DMABUFSIZE 256 380#define DESC_LIST_SIZE 4096 381 382#define MASK_PARITY BIT1 383#define MASK_FRAMING BIT0 384#define MASK_BREAK BIT14 385#define MASK_OVERRUN BIT4 386 387#define GSR 0x00 /* global status */ 388#define JCR 0x04 /* JTAG control */ 389#define IODR 0x08 /* GPIO direction */ 390#define IOER 0x0c /* GPIO interrupt enable */ 391#define IOVR 0x10 /* GPIO value */ 392#define IOSR 0x14 /* GPIO interrupt status */ 393#define TDR 0x80 /* tx data */ 394#define RDR 0x80 /* rx data */ 395#define TCR 0x82 /* tx control */ 396#define TIR 0x84 /* tx idle */ 397#define TPR 0x85 /* tx preamble */ 398#define RCR 0x86 /* rx control */ 399#define VCR 0x88 /* V.24 control */ 400#define CCR 0x89 /* clock control */ 401#define BDR 0x8a /* baud divisor */ 402#define SCR 0x8c /* serial control */ 403#define SSR 0x8e /* serial status */ 404#define RDCSR 0x90 /* rx DMA control/status */ 405#define TDCSR 0x94 /* tx DMA control/status */ 406#define RDDAR 0x98 /* rx DMA descriptor address */ 407#define TDDAR 0x9c /* tx DMA descriptor address */ 408#define XSR 0x40 /* extended sync pattern */ 409#define XCR 0x44 /* extended control */ 410 411#define RXIDLE BIT14 412#define RXBREAK BIT14 413#define IRQ_TXDATA BIT13 414#define IRQ_TXIDLE BIT12 415#define IRQ_TXUNDER BIT11 /* HDLC */ 416#define IRQ_RXDATA BIT10 417#define IRQ_RXIDLE BIT9 /* HDLC */ 418#define IRQ_RXBREAK BIT9 /* async */ 419#define IRQ_RXOVER BIT8 420#define IRQ_DSR BIT7 421#define IRQ_CTS BIT6 422#define IRQ_DCD BIT5 423#define IRQ_RI BIT4 424#define IRQ_ALL 0x3ff0 425#define IRQ_MASTER BIT0 426 427#define slgt_irq_on(info, mask) \ 428 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask))) 429#define slgt_irq_off(info, mask) \ 430 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask))) 431 432static __u8 rd_reg8(struct slgt_info *info, unsigned int addr); 433static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value); 434static __u16 rd_reg16(struct slgt_info *info, unsigned int addr); 435static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value); 436static __u32 rd_reg32(struct slgt_info *info, unsigned int addr); 437static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value); 438 439static void msc_set_vcr(struct slgt_info *info); 440 441static int startup(struct slgt_info *info); 442static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info); 443static void shutdown(struct slgt_info *info); 444static void program_hw(struct slgt_info *info); 445static void change_params(struct slgt_info *info); 446 447static int register_test(struct slgt_info *info); 448static int irq_test(struct slgt_info *info); 449static int loopback_test(struct slgt_info *info); 450static int adapter_test(struct slgt_info *info); 451 452static void reset_adapter(struct slgt_info *info); 453static void reset_port(struct slgt_info *info); 454static void async_mode(struct slgt_info *info); 455static void sync_mode(struct slgt_info *info); 456 457static void rx_stop(struct slgt_info *info); 458static void rx_start(struct slgt_info *info); 459static void reset_rbufs(struct slgt_info *info); 460static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last); 461static void rdma_reset(struct slgt_info *info); 462static bool rx_get_frame(struct slgt_info *info); 463static bool rx_get_buf(struct slgt_info *info); 464 465static void tx_start(struct slgt_info *info); 466static void tx_stop(struct slgt_info *info); 467static void tx_set_idle(struct slgt_info *info); 468static unsigned int free_tbuf_count(struct slgt_info *info); 469static unsigned int tbuf_bytes(struct slgt_info *info); 470static void reset_tbufs(struct slgt_info *info); 471static void tdma_reset(struct slgt_info *info); 472static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count); 473 474static void get_signals(struct slgt_info *info); 475static void set_signals(struct slgt_info *info); 476static void enable_loopback(struct slgt_info *info); 477static void set_rate(struct slgt_info *info, u32 data_rate); 478 479static int bh_action(struct slgt_info *info); 480static void bh_handler(struct work_struct *work); 481static void bh_transmit(struct slgt_info *info); 482static void isr_serial(struct slgt_info *info); 483static void isr_rdma(struct slgt_info *info); 484static void isr_txeom(struct slgt_info *info, unsigned short status); 485static void isr_tdma(struct slgt_info *info); 486 487static int alloc_dma_bufs(struct slgt_info *info); 488static void free_dma_bufs(struct slgt_info *info); 489static int alloc_desc(struct slgt_info *info); 490static void free_desc(struct slgt_info *info); 491static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count); 492static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count); 493 494static int alloc_tmp_rbuf(struct slgt_info *info); 495static void free_tmp_rbuf(struct slgt_info *info); 496 497static void tx_timeout(unsigned long context); 498static void rx_timeout(unsigned long context); 499 500/* 501 * ioctl handlers 502 */ 503static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount); 504static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params); 505static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params); 506static int get_txidle(struct slgt_info *info, int __user *idle_mode); 507static int set_txidle(struct slgt_info *info, int idle_mode); 508static int tx_enable(struct slgt_info *info, int enable); 509static int tx_abort(struct slgt_info *info); 510static int rx_enable(struct slgt_info *info, int enable); 511static int modem_input_wait(struct slgt_info *info,int arg); 512static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr); 513static int tiocmget(struct tty_struct *tty); 514static int tiocmset(struct tty_struct *tty, 515 unsigned int set, unsigned int clear); 516static int set_break(struct tty_struct *tty, int break_state); 517static int get_interface(struct slgt_info *info, int __user *if_mode); 518static int set_interface(struct slgt_info *info, int if_mode); 519static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 520static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 521static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio); 522static int get_xsync(struct slgt_info *info, int __user *if_mode); 523static int set_xsync(struct slgt_info *info, int if_mode); 524static int get_xctrl(struct slgt_info *info, int __user *if_mode); 525static int set_xctrl(struct slgt_info *info, int if_mode); 526 527/* 528 * driver functions 529 */ 530static void add_device(struct slgt_info *info); 531static void device_init(int adapter_num, struct pci_dev *pdev); 532static int claim_resources(struct slgt_info *info); 533static void release_resources(struct slgt_info *info); 534 535/* 536 * DEBUG OUTPUT CODE 537 */ 538#ifndef DBGINFO 539#define DBGINFO(fmt) 540#endif 541#ifndef DBGERR 542#define DBGERR(fmt) 543#endif 544#ifndef DBGBH 545#define DBGBH(fmt) 546#endif 547#ifndef DBGISR 548#define DBGISR(fmt) 549#endif 550 551#ifdef DBGDATA 552static void trace_block(struct slgt_info *info, const char *data, int count, const char *label) 553{ 554 int i; 555 int linecount; 556 printk("%s %s data:\n",info->device_name, label); 557 while(count) { 558 linecount = (count > 16) ? 16 : count; 559 for(i=0; i < linecount; i++) 560 printk("%02X ",(unsigned char)data[i]); 561 for(;i<17;i++) 562 printk(" "); 563 for(i=0;i<linecount;i++) { 564 if (data[i]>=040 && data[i]<=0176) 565 printk("%c",data[i]); 566 else 567 printk("."); 568 } 569 printk("\n"); 570 data += linecount; 571 count -= linecount; 572 } 573} 574#else 575#define DBGDATA(info, buf, size, label) 576#endif 577 578#ifdef DBGTBUF 579static void dump_tbufs(struct slgt_info *info) 580{ 581 int i; 582 printk("tbuf_current=%d\n", info->tbuf_current); 583 for (i=0 ; i < info->tbuf_count ; i++) { 584 printk("%d: count=%04X status=%04X\n", 585 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status)); 586 } 587} 588#else 589#define DBGTBUF(info) 590#endif 591 592#ifdef DBGRBUF 593static void dump_rbufs(struct slgt_info *info) 594{ 595 int i; 596 printk("rbuf_current=%d\n", info->rbuf_current); 597 for (i=0 ; i < info->rbuf_count ; i++) { 598 printk("%d: count=%04X status=%04X\n", 599 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status)); 600 } 601} 602#else 603#define DBGRBUF(info) 604#endif 605 606static inline int sanity_check(struct slgt_info *info, char *devname, const char *name) 607{ 608#ifdef SANITY_CHECK 609 if (!info) { 610 printk("null struct slgt_info for (%s) in %s\n", devname, name); 611 return 1; 612 } 613 if (info->magic != MGSL_MAGIC) { 614 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name); 615 return 1; 616 } 617#else 618 if (!info) 619 return 1; 620#endif 621 return 0; 622} 623 624/** 625 * line discipline callback wrappers 626 * 627 * The wrappers maintain line discipline references 628 * while calling into the line discipline. 629 * 630 * ldisc_receive_buf - pass receive data to line discipline 631 */ 632static void ldisc_receive_buf(struct tty_struct *tty, 633 const __u8 *data, char *flags, int count) 634{ 635 struct tty_ldisc *ld; 636 if (!tty) 637 return; 638 ld = tty_ldisc_ref(tty); 639 if (ld) { 640 if (ld->ops->receive_buf) 641 ld->ops->receive_buf(tty, data, flags, count); 642 tty_ldisc_deref(ld); 643 } 644} 645 646/* tty callbacks */ 647 648static int open(struct tty_struct *tty, struct file *filp) 649{ 650 struct slgt_info *info; 651 int retval, line; 652 unsigned long flags; 653 654 line = tty->index; 655 if (line >= slgt_device_count) { 656 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line)); 657 return -ENODEV; 658 } 659 660 info = slgt_device_list; 661 while(info && info->line != line) 662 info = info->next_device; 663 if (sanity_check(info, tty->name, "open")) 664 return -ENODEV; 665 if (info->init_error) { 666 DBGERR(("%s init error=%d\n", info->device_name, info->init_error)); 667 return -ENODEV; 668 } 669 670 tty->driver_data = info; 671 info->port.tty = tty; 672 673 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count)); 674 675 /* If port is closing, signal caller to try again */ 676 if (info->port.flags & ASYNC_CLOSING){ 677 wait_event_interruptible_tty(tty, info->port.close_wait, 678 !(info->port.flags & ASYNC_CLOSING)); 679 retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ? 680 -EAGAIN : -ERESTARTSYS); 681 goto cleanup; 682 } 683 684 mutex_lock(&info->port.mutex); 685 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0; 686 687 spin_lock_irqsave(&info->netlock, flags); 688 if (info->netcount) { 689 retval = -EBUSY; 690 spin_unlock_irqrestore(&info->netlock, flags); 691 mutex_unlock(&info->port.mutex); 692 goto cleanup; 693 } 694 info->port.count++; 695 spin_unlock_irqrestore(&info->netlock, flags); 696 697 if (info->port.count == 1) { 698 /* 1st open on this device, init hardware */ 699 retval = startup(info); 700 if (retval < 0) { 701 mutex_unlock(&info->port.mutex); 702 goto cleanup; 703 } 704 } 705 mutex_unlock(&info->port.mutex); 706 retval = block_til_ready(tty, filp, info); 707 if (retval) { 708 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval)); 709 goto cleanup; 710 } 711 712 retval = 0; 713 714cleanup: 715 if (retval) { 716 if (tty->count == 1) 717 info->port.tty = NULL; /* tty layer will release tty struct */ 718 if(info->port.count) 719 info->port.count--; 720 } 721 722 DBGINFO(("%s open rc=%d\n", info->device_name, retval)); 723 return retval; 724} 725 726static void close(struct tty_struct *tty, struct file *filp) 727{ 728 struct slgt_info *info = tty->driver_data; 729 730 if (sanity_check(info, tty->name, "close")) 731 return; 732 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count)); 733 734 if (tty_port_close_start(&info->port, tty, filp) == 0) 735 goto cleanup; 736 737 mutex_lock(&info->port.mutex); 738 if (info->port.flags & ASYNC_INITIALIZED) 739 wait_until_sent(tty, info->timeout); 740 flush_buffer(tty); 741 tty_ldisc_flush(tty); 742 743 shutdown(info); 744 mutex_unlock(&info->port.mutex); 745 746 tty_port_close_end(&info->port, tty); 747 info->port.tty = NULL; 748cleanup: 749 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count)); 750} 751 752static void hangup(struct tty_struct *tty) 753{ 754 struct slgt_info *info = tty->driver_data; 755 unsigned long flags; 756 757 if (sanity_check(info, tty->name, "hangup")) 758 return; 759 DBGINFO(("%s hangup\n", info->device_name)); 760 761 flush_buffer(tty); 762 763 mutex_lock(&info->port.mutex); 764 shutdown(info); 765 766 spin_lock_irqsave(&info->port.lock, flags); 767 info->port.count = 0; 768 info->port.flags &= ~ASYNC_NORMAL_ACTIVE; 769 info->port.tty = NULL; 770 spin_unlock_irqrestore(&info->port.lock, flags); 771 mutex_unlock(&info->port.mutex); 772 773 wake_up_interruptible(&info->port.open_wait); 774} 775 776static void set_termios(struct tty_struct *tty, struct ktermios *old_termios) 777{ 778 struct slgt_info *info = tty->driver_data; 779 unsigned long flags; 780 781 DBGINFO(("%s set_termios\n", tty->driver->name)); 782 783 change_params(info); 784 785 /* Handle transition to B0 status */ 786 if (old_termios->c_cflag & CBAUD && 787 !(tty->termios.c_cflag & CBAUD)) { 788 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 789 spin_lock_irqsave(&info->lock,flags); 790 set_signals(info); 791 spin_unlock_irqrestore(&info->lock,flags); 792 } 793 794 /* Handle transition away from B0 status */ 795 if (!(old_termios->c_cflag & CBAUD) && 796 tty->termios.c_cflag & CBAUD) { 797 info->signals |= SerialSignal_DTR; 798 if (!(tty->termios.c_cflag & CRTSCTS) || 799 !test_bit(TTY_THROTTLED, &tty->flags)) { 800 info->signals |= SerialSignal_RTS; 801 } 802 spin_lock_irqsave(&info->lock,flags); 803 set_signals(info); 804 spin_unlock_irqrestore(&info->lock,flags); 805 } 806 807 /* Handle turning off CRTSCTS */ 808 if (old_termios->c_cflag & CRTSCTS && 809 !(tty->termios.c_cflag & CRTSCTS)) { 810 tty->hw_stopped = 0; 811 tx_release(tty); 812 } 813} 814 815static void update_tx_timer(struct slgt_info *info) 816{ 817 /* 818 * use worst case speed of 1200bps to calculate transmit timeout 819 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes) 820 */ 821 if (info->params.mode == MGSL_MODE_HDLC) { 822 int timeout = (tbuf_bytes(info) * 7) + 1000; 823 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout)); 824 } 825} 826 827static int write(struct tty_struct *tty, 828 const unsigned char *buf, int count) 829{ 830 int ret = 0; 831 struct slgt_info *info = tty->driver_data; 832 unsigned long flags; 833 834 if (sanity_check(info, tty->name, "write")) 835 return -EIO; 836 837 DBGINFO(("%s write count=%d\n", info->device_name, count)); 838 839 if (!info->tx_buf || (count > info->max_frame_size)) 840 return -EIO; 841 842 if (!count || tty->stopped || tty->hw_stopped) 843 return 0; 844 845 spin_lock_irqsave(&info->lock, flags); 846 847 if (info->tx_count) { 848 /* send accumulated data from send_char() */ 849 if (!tx_load(info, info->tx_buf, info->tx_count)) 850 goto cleanup; 851 info->tx_count = 0; 852 } 853 854 if (tx_load(info, buf, count)) 855 ret = count; 856 857cleanup: 858 spin_unlock_irqrestore(&info->lock, flags); 859 DBGINFO(("%s write rc=%d\n", info->device_name, ret)); 860 return ret; 861} 862 863static int put_char(struct tty_struct *tty, unsigned char ch) 864{ 865 struct slgt_info *info = tty->driver_data; 866 unsigned long flags; 867 int ret = 0; 868 869 if (sanity_check(info, tty->name, "put_char")) 870 return 0; 871 DBGINFO(("%s put_char(%d)\n", info->device_name, ch)); 872 if (!info->tx_buf) 873 return 0; 874 spin_lock_irqsave(&info->lock,flags); 875 if (info->tx_count < info->max_frame_size) { 876 info->tx_buf[info->tx_count++] = ch; 877 ret = 1; 878 } 879 spin_unlock_irqrestore(&info->lock,flags); 880 return ret; 881} 882 883static void send_xchar(struct tty_struct *tty, char ch) 884{ 885 struct slgt_info *info = tty->driver_data; 886 unsigned long flags; 887 888 if (sanity_check(info, tty->name, "send_xchar")) 889 return; 890 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch)); 891 info->x_char = ch; 892 if (ch) { 893 spin_lock_irqsave(&info->lock,flags); 894 if (!info->tx_enabled) 895 tx_start(info); 896 spin_unlock_irqrestore(&info->lock,flags); 897 } 898} 899 900static void wait_until_sent(struct tty_struct *tty, int timeout) 901{ 902 struct slgt_info *info = tty->driver_data; 903 unsigned long orig_jiffies, char_time; 904 905 if (!info ) 906 return; 907 if (sanity_check(info, tty->name, "wait_until_sent")) 908 return; 909 DBGINFO(("%s wait_until_sent entry\n", info->device_name)); 910 if (!(info->port.flags & ASYNC_INITIALIZED)) 911 goto exit; 912 913 orig_jiffies = jiffies; 914 915 /* Set check interval to 1/5 of estimated time to 916 * send a character, and make it at least 1. The check 917 * interval should also be less than the timeout. 918 * Note: use tight timings here to satisfy the NIST-PCTS. 919 */ 920 921 if (info->params.data_rate) { 922 char_time = info->timeout/(32 * 5); 923 if (!char_time) 924 char_time++; 925 } else 926 char_time = 1; 927 928 if (timeout) 929 char_time = min_t(unsigned long, char_time, timeout); 930 931 while (info->tx_active) { 932 msleep_interruptible(jiffies_to_msecs(char_time)); 933 if (signal_pending(current)) 934 break; 935 if (timeout && time_after(jiffies, orig_jiffies + timeout)) 936 break; 937 } 938exit: 939 DBGINFO(("%s wait_until_sent exit\n", info->device_name)); 940} 941 942static int write_room(struct tty_struct *tty) 943{ 944 struct slgt_info *info = tty->driver_data; 945 int ret; 946 947 if (sanity_check(info, tty->name, "write_room")) 948 return 0; 949 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE; 950 DBGINFO(("%s write_room=%d\n", info->device_name, ret)); 951 return ret; 952} 953 954static void flush_chars(struct tty_struct *tty) 955{ 956 struct slgt_info *info = tty->driver_data; 957 unsigned long flags; 958 959 if (sanity_check(info, tty->name, "flush_chars")) 960 return; 961 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count)); 962 963 if (info->tx_count <= 0 || tty->stopped || 964 tty->hw_stopped || !info->tx_buf) 965 return; 966 967 DBGINFO(("%s flush_chars start transmit\n", info->device_name)); 968 969 spin_lock_irqsave(&info->lock,flags); 970 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count)) 971 info->tx_count = 0; 972 spin_unlock_irqrestore(&info->lock,flags); 973} 974 975static void flush_buffer(struct tty_struct *tty) 976{ 977 struct slgt_info *info = tty->driver_data; 978 unsigned long flags; 979 980 if (sanity_check(info, tty->name, "flush_buffer")) 981 return; 982 DBGINFO(("%s flush_buffer\n", info->device_name)); 983 984 spin_lock_irqsave(&info->lock, flags); 985 info->tx_count = 0; 986 spin_unlock_irqrestore(&info->lock, flags); 987 988 tty_wakeup(tty); 989} 990 991/* 992 * throttle (stop) transmitter 993 */ 994static void tx_hold(struct tty_struct *tty) 995{ 996 struct slgt_info *info = tty->driver_data; 997 unsigned long flags; 998 999 if (sanity_check(info, tty->name, "tx_hold")) 1000 return; 1001 DBGINFO(("%s tx_hold\n", info->device_name)); 1002 spin_lock_irqsave(&info->lock,flags); 1003 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC) 1004 tx_stop(info); 1005 spin_unlock_irqrestore(&info->lock,flags); 1006} 1007 1008/* 1009 * release (start) transmitter 1010 */ 1011static void tx_release(struct tty_struct *tty) 1012{ 1013 struct slgt_info *info = tty->driver_data; 1014 unsigned long flags; 1015 1016 if (sanity_check(info, tty->name, "tx_release")) 1017 return; 1018 DBGINFO(("%s tx_release\n", info->device_name)); 1019 spin_lock_irqsave(&info->lock, flags); 1020 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count)) 1021 info->tx_count = 0; 1022 spin_unlock_irqrestore(&info->lock, flags); 1023} 1024 1025/* 1026 * Service an IOCTL request 1027 * 1028 * Arguments 1029 * 1030 * tty pointer to tty instance data 1031 * cmd IOCTL command code 1032 * arg command argument/context 1033 * 1034 * Return 0 if success, otherwise error code 1035 */ 1036static int ioctl(struct tty_struct *tty, 1037 unsigned int cmd, unsigned long arg) 1038{ 1039 struct slgt_info *info = tty->driver_data; 1040 void __user *argp = (void __user *)arg; 1041 int ret; 1042 1043 if (sanity_check(info, tty->name, "ioctl")) 1044 return -ENODEV; 1045 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd)); 1046 1047 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) && 1048 (cmd != TIOCMIWAIT)) { 1049 if (tty->flags & (1 << TTY_IO_ERROR)) 1050 return -EIO; 1051 } 1052 1053 switch (cmd) { 1054 case MGSL_IOCWAITEVENT: 1055 return wait_mgsl_event(info, argp); 1056 case TIOCMIWAIT: 1057 return modem_input_wait(info,(int)arg); 1058 case MGSL_IOCSGPIO: 1059 return set_gpio(info, argp); 1060 case MGSL_IOCGGPIO: 1061 return get_gpio(info, argp); 1062 case MGSL_IOCWAITGPIO: 1063 return wait_gpio(info, argp); 1064 case MGSL_IOCGXSYNC: 1065 return get_xsync(info, argp); 1066 case MGSL_IOCSXSYNC: 1067 return set_xsync(info, (int)arg); 1068 case MGSL_IOCGXCTRL: 1069 return get_xctrl(info, argp); 1070 case MGSL_IOCSXCTRL: 1071 return set_xctrl(info, (int)arg); 1072 } 1073 mutex_lock(&info->port.mutex); 1074 switch (cmd) { 1075 case MGSL_IOCGPARAMS: 1076 ret = get_params(info, argp); 1077 break; 1078 case MGSL_IOCSPARAMS: 1079 ret = set_params(info, argp); 1080 break; 1081 case MGSL_IOCGTXIDLE: 1082 ret = get_txidle(info, argp); 1083 break; 1084 case MGSL_IOCSTXIDLE: 1085 ret = set_txidle(info, (int)arg); 1086 break; 1087 case MGSL_IOCTXENABLE: 1088 ret = tx_enable(info, (int)arg); 1089 break; 1090 case MGSL_IOCRXENABLE: 1091 ret = rx_enable(info, (int)arg); 1092 break; 1093 case MGSL_IOCTXABORT: 1094 ret = tx_abort(info); 1095 break; 1096 case MGSL_IOCGSTATS: 1097 ret = get_stats(info, argp); 1098 break; 1099 case MGSL_IOCGIF: 1100 ret = get_interface(info, argp); 1101 break; 1102 case MGSL_IOCSIF: 1103 ret = set_interface(info,(int)arg); 1104 break; 1105 default: 1106 ret = -ENOIOCTLCMD; 1107 } 1108 mutex_unlock(&info->port.mutex); 1109 return ret; 1110} 1111 1112static int get_icount(struct tty_struct *tty, 1113 struct serial_icounter_struct *icount) 1114 1115{ 1116 struct slgt_info *info = tty->driver_data; 1117 struct mgsl_icount cnow; /* kernel counter temps */ 1118 unsigned long flags; 1119 1120 spin_lock_irqsave(&info->lock,flags); 1121 cnow = info->icount; 1122 spin_unlock_irqrestore(&info->lock,flags); 1123 1124 icount->cts = cnow.cts; 1125 icount->dsr = cnow.dsr; 1126 icount->rng = cnow.rng; 1127 icount->dcd = cnow.dcd; 1128 icount->rx = cnow.rx; 1129 icount->tx = cnow.tx; 1130 icount->frame = cnow.frame; 1131 icount->overrun = cnow.overrun; 1132 icount->parity = cnow.parity; 1133 icount->brk = cnow.brk; 1134 icount->buf_overrun = cnow.buf_overrun; 1135 1136 return 0; 1137} 1138 1139/* 1140 * support for 32 bit ioctl calls on 64 bit systems 1141 */ 1142#ifdef CONFIG_COMPAT 1143static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params) 1144{ 1145 struct MGSL_PARAMS32 tmp_params; 1146 1147 DBGINFO(("%s get_params32\n", info->device_name)); 1148 memset(&tmp_params, 0, sizeof(tmp_params)); 1149 tmp_params.mode = (compat_ulong_t)info->params.mode; 1150 tmp_params.loopback = info->params.loopback; 1151 tmp_params.flags = info->params.flags; 1152 tmp_params.encoding = info->params.encoding; 1153 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed; 1154 tmp_params.addr_filter = info->params.addr_filter; 1155 tmp_params.crc_type = info->params.crc_type; 1156 tmp_params.preamble_length = info->params.preamble_length; 1157 tmp_params.preamble = info->params.preamble; 1158 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate; 1159 tmp_params.data_bits = info->params.data_bits; 1160 tmp_params.stop_bits = info->params.stop_bits; 1161 tmp_params.parity = info->params.parity; 1162 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32))) 1163 return -EFAULT; 1164 return 0; 1165} 1166 1167static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params) 1168{ 1169 struct MGSL_PARAMS32 tmp_params; 1170 1171 DBGINFO(("%s set_params32\n", info->device_name)); 1172 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32))) 1173 return -EFAULT; 1174 1175 spin_lock(&info->lock); 1176 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) { 1177 info->base_clock = tmp_params.clock_speed; 1178 } else { 1179 info->params.mode = tmp_params.mode; 1180 info->params.loopback = tmp_params.loopback; 1181 info->params.flags = tmp_params.flags; 1182 info->params.encoding = tmp_params.encoding; 1183 info->params.clock_speed = tmp_params.clock_speed; 1184 info->params.addr_filter = tmp_params.addr_filter; 1185 info->params.crc_type = tmp_params.crc_type; 1186 info->params.preamble_length = tmp_params.preamble_length; 1187 info->params.preamble = tmp_params.preamble; 1188 info->params.data_rate = tmp_params.data_rate; 1189 info->params.data_bits = tmp_params.data_bits; 1190 info->params.stop_bits = tmp_params.stop_bits; 1191 info->params.parity = tmp_params.parity; 1192 } 1193 spin_unlock(&info->lock); 1194 1195 program_hw(info); 1196 1197 return 0; 1198} 1199 1200static long slgt_compat_ioctl(struct tty_struct *tty, 1201 unsigned int cmd, unsigned long arg) 1202{ 1203 struct slgt_info *info = tty->driver_data; 1204 int rc = -ENOIOCTLCMD; 1205 1206 if (sanity_check(info, tty->name, "compat_ioctl")) 1207 return -ENODEV; 1208 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd)); 1209 1210 switch (cmd) { 1211 1212 case MGSL_IOCSPARAMS32: 1213 rc = set_params32(info, compat_ptr(arg)); 1214 break; 1215 1216 case MGSL_IOCGPARAMS32: 1217 rc = get_params32(info, compat_ptr(arg)); 1218 break; 1219 1220 case MGSL_IOCGPARAMS: 1221 case MGSL_IOCSPARAMS: 1222 case MGSL_IOCGTXIDLE: 1223 case MGSL_IOCGSTATS: 1224 case MGSL_IOCWAITEVENT: 1225 case MGSL_IOCGIF: 1226 case MGSL_IOCSGPIO: 1227 case MGSL_IOCGGPIO: 1228 case MGSL_IOCWAITGPIO: 1229 case MGSL_IOCGXSYNC: 1230 case MGSL_IOCGXCTRL: 1231 case MGSL_IOCSTXIDLE: 1232 case MGSL_IOCTXENABLE: 1233 case MGSL_IOCRXENABLE: 1234 case MGSL_IOCTXABORT: 1235 case TIOCMIWAIT: 1236 case MGSL_IOCSIF: 1237 case MGSL_IOCSXSYNC: 1238 case MGSL_IOCSXCTRL: 1239 rc = ioctl(tty, cmd, arg); 1240 break; 1241 } 1242 1243 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc)); 1244 return rc; 1245} 1246#else 1247#define slgt_compat_ioctl NULL 1248#endif /* ifdef CONFIG_COMPAT */ 1249 1250/* 1251 * proc fs support 1252 */ 1253static inline void line_info(struct seq_file *m, struct slgt_info *info) 1254{ 1255 char stat_buf[30]; 1256 unsigned long flags; 1257 1258 seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n", 1259 info->device_name, info->phys_reg_addr, 1260 info->irq_level, info->max_frame_size); 1261 1262 /* output current serial signal states */ 1263 spin_lock_irqsave(&info->lock,flags); 1264 get_signals(info); 1265 spin_unlock_irqrestore(&info->lock,flags); 1266 1267 stat_buf[0] = 0; 1268 stat_buf[1] = 0; 1269 if (info->signals & SerialSignal_RTS) 1270 strcat(stat_buf, "|RTS"); 1271 if (info->signals & SerialSignal_CTS) 1272 strcat(stat_buf, "|CTS"); 1273 if (info->signals & SerialSignal_DTR) 1274 strcat(stat_buf, "|DTR"); 1275 if (info->signals & SerialSignal_DSR) 1276 strcat(stat_buf, "|DSR"); 1277 if (info->signals & SerialSignal_DCD) 1278 strcat(stat_buf, "|CD"); 1279 if (info->signals & SerialSignal_RI) 1280 strcat(stat_buf, "|RI"); 1281 1282 if (info->params.mode != MGSL_MODE_ASYNC) { 1283 seq_printf(m, "\tHDLC txok:%d rxok:%d", 1284 info->icount.txok, info->icount.rxok); 1285 if (info->icount.txunder) 1286 seq_printf(m, " txunder:%d", info->icount.txunder); 1287 if (info->icount.txabort) 1288 seq_printf(m, " txabort:%d", info->icount.txabort); 1289 if (info->icount.rxshort) 1290 seq_printf(m, " rxshort:%d", info->icount.rxshort); 1291 if (info->icount.rxlong) 1292 seq_printf(m, " rxlong:%d", info->icount.rxlong); 1293 if (info->icount.rxover) 1294 seq_printf(m, " rxover:%d", info->icount.rxover); 1295 if (info->icount.rxcrc) 1296 seq_printf(m, " rxcrc:%d", info->icount.rxcrc); 1297 } else { 1298 seq_printf(m, "\tASYNC tx:%d rx:%d", 1299 info->icount.tx, info->icount.rx); 1300 if (info->icount.frame) 1301 seq_printf(m, " fe:%d", info->icount.frame); 1302 if (info->icount.parity) 1303 seq_printf(m, " pe:%d", info->icount.parity); 1304 if (info->icount.brk) 1305 seq_printf(m, " brk:%d", info->icount.brk); 1306 if (info->icount.overrun) 1307 seq_printf(m, " oe:%d", info->icount.overrun); 1308 } 1309 1310 /* Append serial signal status to end */ 1311 seq_printf(m, " %s\n", stat_buf+1); 1312 1313 seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n", 1314 info->tx_active,info->bh_requested,info->bh_running, 1315 info->pending_bh); 1316} 1317 1318/* Called to print information about devices 1319 */ 1320static int synclink_gt_proc_show(struct seq_file *m, void *v) 1321{ 1322 struct slgt_info *info; 1323 1324 seq_puts(m, "synclink_gt driver\n"); 1325 1326 info = slgt_device_list; 1327 while( info ) { 1328 line_info(m, info); 1329 info = info->next_device; 1330 } 1331 return 0; 1332} 1333 1334static int synclink_gt_proc_open(struct inode *inode, struct file *file) 1335{ 1336 return single_open(file, synclink_gt_proc_show, NULL); 1337} 1338 1339static const struct file_operations synclink_gt_proc_fops = { 1340 .owner = THIS_MODULE, 1341 .open = synclink_gt_proc_open, 1342 .read = seq_read, 1343 .llseek = seq_lseek, 1344 .release = single_release, 1345}; 1346 1347/* 1348 * return count of bytes in transmit buffer 1349 */ 1350static int chars_in_buffer(struct tty_struct *tty) 1351{ 1352 struct slgt_info *info = tty->driver_data; 1353 int count; 1354 if (sanity_check(info, tty->name, "chars_in_buffer")) 1355 return 0; 1356 count = tbuf_bytes(info); 1357 DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count)); 1358 return count; 1359} 1360 1361/* 1362 * signal remote device to throttle send data (our receive data) 1363 */ 1364static void throttle(struct tty_struct * tty) 1365{ 1366 struct slgt_info *info = tty->driver_data; 1367 unsigned long flags; 1368 1369 if (sanity_check(info, tty->name, "throttle")) 1370 return; 1371 DBGINFO(("%s throttle\n", info->device_name)); 1372 if (I_IXOFF(tty)) 1373 send_xchar(tty, STOP_CHAR(tty)); 1374 if (tty->termios.c_cflag & CRTSCTS) { 1375 spin_lock_irqsave(&info->lock,flags); 1376 info->signals &= ~SerialSignal_RTS; 1377 set_signals(info); 1378 spin_unlock_irqrestore(&info->lock,flags); 1379 } 1380} 1381 1382/* 1383 * signal remote device to stop throttling send data (our receive data) 1384 */ 1385static void unthrottle(struct tty_struct * tty) 1386{ 1387 struct slgt_info *info = tty->driver_data; 1388 unsigned long flags; 1389 1390 if (sanity_check(info, tty->name, "unthrottle")) 1391 return; 1392 DBGINFO(("%s unthrottle\n", info->device_name)); 1393 if (I_IXOFF(tty)) { 1394 if (info->x_char) 1395 info->x_char = 0; 1396 else 1397 send_xchar(tty, START_CHAR(tty)); 1398 } 1399 if (tty->termios.c_cflag & CRTSCTS) { 1400 spin_lock_irqsave(&info->lock,flags); 1401 info->signals |= SerialSignal_RTS; 1402 set_signals(info); 1403 spin_unlock_irqrestore(&info->lock,flags); 1404 } 1405} 1406 1407/* 1408 * set or clear transmit break condition 1409 * break_state -1=set break condition, 0=clear 1410 */ 1411static int set_break(struct tty_struct *tty, int break_state) 1412{ 1413 struct slgt_info *info = tty->driver_data; 1414 unsigned short value; 1415 unsigned long flags; 1416 1417 if (sanity_check(info, tty->name, "set_break")) 1418 return -EINVAL; 1419 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state)); 1420 1421 spin_lock_irqsave(&info->lock,flags); 1422 value = rd_reg16(info, TCR); 1423 if (break_state == -1) 1424 value |= BIT6; 1425 else 1426 value &= ~BIT6; 1427 wr_reg16(info, TCR, value); 1428 spin_unlock_irqrestore(&info->lock,flags); 1429 return 0; 1430} 1431 1432#if SYNCLINK_GENERIC_HDLC 1433 1434/** 1435 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.) 1436 * set encoding and frame check sequence (FCS) options 1437 * 1438 * dev pointer to network device structure 1439 * encoding serial encoding setting 1440 * parity FCS setting 1441 * 1442 * returns 0 if success, otherwise error code 1443 */ 1444static int hdlcdev_attach(struct net_device *dev, unsigned short encoding, 1445 unsigned short parity) 1446{ 1447 struct slgt_info *info = dev_to_port(dev); 1448 unsigned char new_encoding; 1449 unsigned short new_crctype; 1450 1451 /* return error if TTY interface open */ 1452 if (info->port.count) 1453 return -EBUSY; 1454 1455 DBGINFO(("%s hdlcdev_attach\n", info->device_name)); 1456 1457 switch (encoding) 1458 { 1459 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break; 1460 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break; 1461 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break; 1462 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break; 1463 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break; 1464 default: return -EINVAL; 1465 } 1466 1467 switch (parity) 1468 { 1469 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break; 1470 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break; 1471 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break; 1472 default: return -EINVAL; 1473 } 1474 1475 info->params.encoding = new_encoding; 1476 info->params.crc_type = new_crctype; 1477 1478 /* if network interface up, reprogram hardware */ 1479 if (info->netcount) 1480 program_hw(info); 1481 1482 return 0; 1483} 1484 1485/** 1486 * called by generic HDLC layer to send frame 1487 * 1488 * skb socket buffer containing HDLC frame 1489 * dev pointer to network device structure 1490 */ 1491static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb, 1492 struct net_device *dev) 1493{ 1494 struct slgt_info *info = dev_to_port(dev); 1495 unsigned long flags; 1496 1497 DBGINFO(("%s hdlc_xmit\n", dev->name)); 1498 1499 if (!skb->len) 1500 return NETDEV_TX_OK; 1501 1502 /* stop sending until this frame completes */ 1503 netif_stop_queue(dev); 1504 1505 /* update network statistics */ 1506 dev->stats.tx_packets++; 1507 dev->stats.tx_bytes += skb->len; 1508 1509 /* save start time for transmit timeout detection */ 1510 dev->trans_start = jiffies; 1511 1512 spin_lock_irqsave(&info->lock, flags); 1513 tx_load(info, skb->data, skb->len); 1514 spin_unlock_irqrestore(&info->lock, flags); 1515 1516 /* done with socket buffer, so free it */ 1517 dev_kfree_skb(skb); 1518 1519 return NETDEV_TX_OK; 1520} 1521 1522/** 1523 * called by network layer when interface enabled 1524 * claim resources and initialize hardware 1525 * 1526 * dev pointer to network device structure 1527 * 1528 * returns 0 if success, otherwise error code 1529 */ 1530static int hdlcdev_open(struct net_device *dev) 1531{ 1532 struct slgt_info *info = dev_to_port(dev); 1533 int rc; 1534 unsigned long flags; 1535 1536 if (!try_module_get(THIS_MODULE)) 1537 return -EBUSY; 1538 1539 DBGINFO(("%s hdlcdev_open\n", dev->name)); 1540 1541 /* generic HDLC layer open processing */ 1542 if ((rc = hdlc_open(dev))) 1543 return rc; 1544 1545 /* arbitrate between network and tty opens */ 1546 spin_lock_irqsave(&info->netlock, flags); 1547 if (info->port.count != 0 || info->netcount != 0) { 1548 DBGINFO(("%s hdlc_open busy\n", dev->name)); 1549 spin_unlock_irqrestore(&info->netlock, flags); 1550 return -EBUSY; 1551 } 1552 info->netcount=1; 1553 spin_unlock_irqrestore(&info->netlock, flags); 1554 1555 /* claim resources and init adapter */ 1556 if ((rc = startup(info)) != 0) { 1557 spin_lock_irqsave(&info->netlock, flags); 1558 info->netcount=0; 1559 spin_unlock_irqrestore(&info->netlock, flags); 1560 return rc; 1561 } 1562 1563 /* assert RTS and DTR, apply hardware settings */ 1564 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 1565 program_hw(info); 1566 1567 /* enable network layer transmit */ 1568 dev->trans_start = jiffies; 1569 netif_start_queue(dev); 1570 1571 /* inform generic HDLC layer of current DCD status */ 1572 spin_lock_irqsave(&info->lock, flags); 1573 get_signals(info); 1574 spin_unlock_irqrestore(&info->lock, flags); 1575 if (info->signals & SerialSignal_DCD) 1576 netif_carrier_on(dev); 1577 else 1578 netif_carrier_off(dev); 1579 return 0; 1580} 1581 1582/** 1583 * called by network layer when interface is disabled 1584 * shutdown hardware and release resources 1585 * 1586 * dev pointer to network device structure 1587 * 1588 * returns 0 if success, otherwise error code 1589 */ 1590static int hdlcdev_close(struct net_device *dev) 1591{ 1592 struct slgt_info *info = dev_to_port(dev); 1593 unsigned long flags; 1594 1595 DBGINFO(("%s hdlcdev_close\n", dev->name)); 1596 1597 netif_stop_queue(dev); 1598 1599 /* shutdown adapter and release resources */ 1600 shutdown(info); 1601 1602 hdlc_close(dev); 1603 1604 spin_lock_irqsave(&info->netlock, flags); 1605 info->netcount=0; 1606 spin_unlock_irqrestore(&info->netlock, flags); 1607 1608 module_put(THIS_MODULE); 1609 return 0; 1610} 1611 1612/** 1613 * called by network layer to process IOCTL call to network device 1614 * 1615 * dev pointer to network device structure 1616 * ifr pointer to network interface request structure 1617 * cmd IOCTL command code 1618 * 1619 * returns 0 if success, otherwise error code 1620 */ 1621static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) 1622{ 1623 const size_t size = sizeof(sync_serial_settings); 1624 sync_serial_settings new_line; 1625 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync; 1626 struct slgt_info *info = dev_to_port(dev); 1627 unsigned int flags; 1628 1629 DBGINFO(("%s hdlcdev_ioctl\n", dev->name)); 1630 1631 /* return error if TTY interface open */ 1632 if (info->port.count) 1633 return -EBUSY; 1634 1635 if (cmd != SIOCWANDEV) 1636 return hdlc_ioctl(dev, ifr, cmd); 1637 1638 memset(&new_line, 0, sizeof(new_line)); 1639 1640 switch(ifr->ifr_settings.type) { 1641 case IF_GET_IFACE: /* return current sync_serial_settings */ 1642 1643 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL; 1644 if (ifr->ifr_settings.size < size) { 1645 ifr->ifr_settings.size = size; /* data size wanted */ 1646 return -ENOBUFS; 1647 } 1648 1649 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1650 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1651 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1652 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); 1653 1654 switch (flags){ 1655 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break; 1656 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break; 1657 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break; 1658 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break; 1659 default: new_line.clock_type = CLOCK_DEFAULT; 1660 } 1661 1662 new_line.clock_rate = info->params.clock_speed; 1663 new_line.loopback = info->params.loopback ? 1:0; 1664 1665 if (copy_to_user(line, &new_line, size)) 1666 return -EFAULT; 1667 return 0; 1668 1669 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */ 1670 1671 if(!capable(CAP_NET_ADMIN)) 1672 return -EPERM; 1673 if (copy_from_user(&new_line, line, size)) 1674 return -EFAULT; 1675 1676 switch (new_line.clock_type) 1677 { 1678 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break; 1679 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break; 1680 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break; 1681 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break; 1682 case CLOCK_DEFAULT: flags = info->params.flags & 1683 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1684 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1685 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1686 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break; 1687 default: return -EINVAL; 1688 } 1689 1690 if (new_line.loopback != 0 && new_line.loopback != 1) 1691 return -EINVAL; 1692 1693 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL | 1694 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN | 1695 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL | 1696 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); 1697 info->params.flags |= flags; 1698 1699 info->params.loopback = new_line.loopback; 1700 1701 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG)) 1702 info->params.clock_speed = new_line.clock_rate; 1703 else 1704 info->params.clock_speed = 0; 1705 1706 /* if network interface up, reprogram hardware */ 1707 if (info->netcount) 1708 program_hw(info); 1709 return 0; 1710 1711 default: 1712 return hdlc_ioctl(dev, ifr, cmd); 1713 } 1714} 1715 1716/** 1717 * called by network layer when transmit timeout is detected 1718 * 1719 * dev pointer to network device structure 1720 */ 1721static void hdlcdev_tx_timeout(struct net_device *dev) 1722{ 1723 struct slgt_info *info = dev_to_port(dev); 1724 unsigned long flags; 1725 1726 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name)); 1727 1728 dev->stats.tx_errors++; 1729 dev->stats.tx_aborted_errors++; 1730 1731 spin_lock_irqsave(&info->lock,flags); 1732 tx_stop(info); 1733 spin_unlock_irqrestore(&info->lock,flags); 1734 1735 netif_wake_queue(dev); 1736} 1737 1738/** 1739 * called by device driver when transmit completes 1740 * reenable network layer transmit if stopped 1741 * 1742 * info pointer to device instance information 1743 */ 1744static void hdlcdev_tx_done(struct slgt_info *info) 1745{ 1746 if (netif_queue_stopped(info->netdev)) 1747 netif_wake_queue(info->netdev); 1748} 1749 1750/** 1751 * called by device driver when frame received 1752 * pass frame to network layer 1753 * 1754 * info pointer to device instance information 1755 * buf pointer to buffer contianing frame data 1756 * size count of data bytes in buf 1757 */ 1758static void hdlcdev_rx(struct slgt_info *info, char *buf, int size) 1759{ 1760 struct sk_buff *skb = dev_alloc_skb(size); 1761 struct net_device *dev = info->netdev; 1762 1763 DBGINFO(("%s hdlcdev_rx\n", dev->name)); 1764 1765 if (skb == NULL) { 1766 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name)); 1767 dev->stats.rx_dropped++; 1768 return; 1769 } 1770 1771 memcpy(skb_put(skb, size), buf, size); 1772 1773 skb->protocol = hdlc_type_trans(skb, dev); 1774 1775 dev->stats.rx_packets++; 1776 dev->stats.rx_bytes += size; 1777 1778 netif_rx(skb); 1779} 1780 1781static const struct net_device_ops hdlcdev_ops = { 1782 .ndo_open = hdlcdev_open, 1783 .ndo_stop = hdlcdev_close, 1784 .ndo_change_mtu = hdlc_change_mtu, 1785 .ndo_start_xmit = hdlc_start_xmit, 1786 .ndo_do_ioctl = hdlcdev_ioctl, 1787 .ndo_tx_timeout = hdlcdev_tx_timeout, 1788}; 1789 1790/** 1791 * called by device driver when adding device instance 1792 * do generic HDLC initialization 1793 * 1794 * info pointer to device instance information 1795 * 1796 * returns 0 if success, otherwise error code 1797 */ 1798static int hdlcdev_init(struct slgt_info *info) 1799{ 1800 int rc; 1801 struct net_device *dev; 1802 hdlc_device *hdlc; 1803 1804 /* allocate and initialize network and HDLC layer objects */ 1805 1806 if (!(dev = alloc_hdlcdev(info))) { 1807 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name); 1808 return -ENOMEM; 1809 } 1810 1811 /* for network layer reporting purposes only */ 1812 dev->mem_start = info->phys_reg_addr; 1813 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1; 1814 dev->irq = info->irq_level; 1815 1816 /* network layer callbacks and settings */ 1817 dev->netdev_ops = &hdlcdev_ops; 1818 dev->watchdog_timeo = 10 * HZ; 1819 dev->tx_queue_len = 50; 1820 1821 /* generic HDLC layer callbacks and settings */ 1822 hdlc = dev_to_hdlc(dev); 1823 hdlc->attach = hdlcdev_attach; 1824 hdlc->xmit = hdlcdev_xmit; 1825 1826 /* register objects with HDLC layer */ 1827 if ((rc = register_hdlc_device(dev))) { 1828 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__); 1829 free_netdev(dev); 1830 return rc; 1831 } 1832 1833 info->netdev = dev; 1834 return 0; 1835} 1836 1837/** 1838 * called by device driver when removing device instance 1839 * do generic HDLC cleanup 1840 * 1841 * info pointer to device instance information 1842 */ 1843static void hdlcdev_exit(struct slgt_info *info) 1844{ 1845 unregister_hdlc_device(info->netdev); 1846 free_netdev(info->netdev); 1847 info->netdev = NULL; 1848} 1849 1850#endif /* ifdef CONFIG_HDLC */ 1851 1852/* 1853 * get async data from rx DMA buffers 1854 */ 1855static void rx_async(struct slgt_info *info) 1856{ 1857 struct mgsl_icount *icount = &info->icount; 1858 unsigned int start, end; 1859 unsigned char *p; 1860 unsigned char status; 1861 struct slgt_desc *bufs = info->rbufs; 1862 int i, count; 1863 int chars = 0; 1864 int stat; 1865 unsigned char ch; 1866 1867 start = end = info->rbuf_current; 1868 1869 while(desc_complete(bufs[end])) { 1870 count = desc_count(bufs[end]) - info->rbuf_index; 1871 p = bufs[end].buf + info->rbuf_index; 1872 1873 DBGISR(("%s rx_async count=%d\n", info->device_name, count)); 1874 DBGDATA(info, p, count, "rx"); 1875 1876 for(i=0 ; i < count; i+=2, p+=2) { 1877 ch = *p; 1878 icount->rx++; 1879 1880 stat = 0; 1881 1882 if ((status = *(p+1) & (BIT1 + BIT0))) { 1883 if (status & BIT1) 1884 icount->parity++; 1885 else if (status & BIT0) 1886 icount->frame++; 1887 /* discard char if tty control flags say so */ 1888 if (status & info->ignore_status_mask) 1889 continue; 1890 if (status & BIT1) 1891 stat = TTY_PARITY; 1892 else if (status & BIT0) 1893 stat = TTY_FRAME; 1894 } 1895 tty_insert_flip_char(&info->port, ch, stat); 1896 chars++; 1897 } 1898 1899 if (i < count) { 1900 /* receive buffer not completed */ 1901 info->rbuf_index += i; 1902 mod_timer(&info->rx_timer, jiffies + 1); 1903 break; 1904 } 1905 1906 info->rbuf_index = 0; 1907 free_rbufs(info, end, end); 1908 1909 if (++end == info->rbuf_count) 1910 end = 0; 1911 1912 /* if entire list searched then no frame available */ 1913 if (end == start) 1914 break; 1915 } 1916 1917 if (chars) 1918 tty_flip_buffer_push(&info->port); 1919} 1920 1921/* 1922 * return next bottom half action to perform 1923 */ 1924static int bh_action(struct slgt_info *info) 1925{ 1926 unsigned long flags; 1927 int rc; 1928 1929 spin_lock_irqsave(&info->lock,flags); 1930 1931 if (info->pending_bh & BH_RECEIVE) { 1932 info->pending_bh &= ~BH_RECEIVE; 1933 rc = BH_RECEIVE; 1934 } else if (info->pending_bh & BH_TRANSMIT) { 1935 info->pending_bh &= ~BH_TRANSMIT; 1936 rc = BH_TRANSMIT; 1937 } else if (info->pending_bh & BH_STATUS) { 1938 info->pending_bh &= ~BH_STATUS; 1939 rc = BH_STATUS; 1940 } else { 1941 /* Mark BH routine as complete */ 1942 info->bh_running = false; 1943 info->bh_requested = false; 1944 rc = 0; 1945 } 1946 1947 spin_unlock_irqrestore(&info->lock,flags); 1948 1949 return rc; 1950} 1951 1952/* 1953 * perform bottom half processing 1954 */ 1955static void bh_handler(struct work_struct *work) 1956{ 1957 struct slgt_info *info = container_of(work, struct slgt_info, task); 1958 int action; 1959 1960 info->bh_running = true; 1961 1962 while((action = bh_action(info))) { 1963 switch (action) { 1964 case BH_RECEIVE: 1965 DBGBH(("%s bh receive\n", info->device_name)); 1966 switch(info->params.mode) { 1967 case MGSL_MODE_ASYNC: 1968 rx_async(info); 1969 break; 1970 case MGSL_MODE_HDLC: 1971 while(rx_get_frame(info)); 1972 break; 1973 case MGSL_MODE_RAW: 1974 case MGSL_MODE_MONOSYNC: 1975 case MGSL_MODE_BISYNC: 1976 case MGSL_MODE_XSYNC: 1977 while(rx_get_buf(info)); 1978 break; 1979 } 1980 /* restart receiver if rx DMA buffers exhausted */ 1981 if (info->rx_restart) 1982 rx_start(info); 1983 break; 1984 case BH_TRANSMIT: 1985 bh_transmit(info); 1986 break; 1987 case BH_STATUS: 1988 DBGBH(("%s bh status\n", info->device_name)); 1989 info->ri_chkcount = 0; 1990 info->dsr_chkcount = 0; 1991 info->dcd_chkcount = 0; 1992 info->cts_chkcount = 0; 1993 break; 1994 default: 1995 DBGBH(("%s unknown action\n", info->device_name)); 1996 break; 1997 } 1998 } 1999 DBGBH(("%s bh_handler exit\n", info->device_name)); 2000} 2001 2002static void bh_transmit(struct slgt_info *info) 2003{ 2004 struct tty_struct *tty = info->port.tty; 2005 2006 DBGBH(("%s bh_transmit\n", info->device_name)); 2007 if (tty) 2008 tty_wakeup(tty); 2009} 2010 2011static void dsr_change(struct slgt_info *info, unsigned short status) 2012{ 2013 if (status & BIT3) { 2014 info->signals |= SerialSignal_DSR; 2015 info->input_signal_events.dsr_up++; 2016 } else { 2017 info->signals &= ~SerialSignal_DSR; 2018 info->input_signal_events.dsr_down++; 2019 } 2020 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals)); 2021 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2022 slgt_irq_off(info, IRQ_DSR); 2023 return; 2024 } 2025 info->icount.dsr++; 2026 wake_up_interruptible(&info->status_event_wait_q); 2027 wake_up_interruptible(&info->event_wait_q); 2028 info->pending_bh |= BH_STATUS; 2029} 2030 2031static void cts_change(struct slgt_info *info, unsigned short status) 2032{ 2033 if (status & BIT2) { 2034 info->signals |= SerialSignal_CTS; 2035 info->input_signal_events.cts_up++; 2036 } else { 2037 info->signals &= ~SerialSignal_CTS; 2038 info->input_signal_events.cts_down++; 2039 } 2040 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals)); 2041 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2042 slgt_irq_off(info, IRQ_CTS); 2043 return; 2044 } 2045 info->icount.cts++; 2046 wake_up_interruptible(&info->status_event_wait_q); 2047 wake_up_interruptible(&info->event_wait_q); 2048 info->pending_bh |= BH_STATUS; 2049 2050 if (tty_port_cts_enabled(&info->port)) { 2051 if (info->port.tty) { 2052 if (info->port.tty->hw_stopped) { 2053 if (info->signals & SerialSignal_CTS) { 2054 info->port.tty->hw_stopped = 0; 2055 info->pending_bh |= BH_TRANSMIT; 2056 return; 2057 } 2058 } else { 2059 if (!(info->signals & SerialSignal_CTS)) 2060 info->port.tty->hw_stopped = 1; 2061 } 2062 } 2063 } 2064} 2065 2066static void dcd_change(struct slgt_info *info, unsigned short status) 2067{ 2068 if (status & BIT1) { 2069 info->signals |= SerialSignal_DCD; 2070 info->input_signal_events.dcd_up++; 2071 } else { 2072 info->signals &= ~SerialSignal_DCD; 2073 info->input_signal_events.dcd_down++; 2074 } 2075 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals)); 2076 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2077 slgt_irq_off(info, IRQ_DCD); 2078 return; 2079 } 2080 info->icount.dcd++; 2081#if SYNCLINK_GENERIC_HDLC 2082 if (info->netcount) { 2083 if (info->signals & SerialSignal_DCD) 2084 netif_carrier_on(info->netdev); 2085 else 2086 netif_carrier_off(info->netdev); 2087 } 2088#endif 2089 wake_up_interruptible(&info->status_event_wait_q); 2090 wake_up_interruptible(&info->event_wait_q); 2091 info->pending_bh |= BH_STATUS; 2092 2093 if (info->port.flags & ASYNC_CHECK_CD) { 2094 if (info->signals & SerialSignal_DCD) 2095 wake_up_interruptible(&info->port.open_wait); 2096 else { 2097 if (info->port.tty) 2098 tty_hangup(info->port.tty); 2099 } 2100 } 2101} 2102 2103static void ri_change(struct slgt_info *info, unsigned short status) 2104{ 2105 if (status & BIT0) { 2106 info->signals |= SerialSignal_RI; 2107 info->input_signal_events.ri_up++; 2108 } else { 2109 info->signals &= ~SerialSignal_RI; 2110 info->input_signal_events.ri_down++; 2111 } 2112 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals)); 2113 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) { 2114 slgt_irq_off(info, IRQ_RI); 2115 return; 2116 } 2117 info->icount.rng++; 2118 wake_up_interruptible(&info->status_event_wait_q); 2119 wake_up_interruptible(&info->event_wait_q); 2120 info->pending_bh |= BH_STATUS; 2121} 2122 2123static void isr_rxdata(struct slgt_info *info) 2124{ 2125 unsigned int count = info->rbuf_fill_count; 2126 unsigned int i = info->rbuf_fill_index; 2127 unsigned short reg; 2128 2129 while (rd_reg16(info, SSR) & IRQ_RXDATA) { 2130 reg = rd_reg16(info, RDR); 2131 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg)); 2132 if (desc_complete(info->rbufs[i])) { 2133 /* all buffers full */ 2134 rx_stop(info); 2135 info->rx_restart = 1; 2136 continue; 2137 } 2138 info->rbufs[i].buf[count++] = (unsigned char)reg; 2139 /* async mode saves status byte to buffer for each data byte */ 2140 if (info->params.mode == MGSL_MODE_ASYNC) 2141 info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8); 2142 if (count == info->rbuf_fill_level || (reg & BIT10)) { 2143 /* buffer full or end of frame */ 2144 set_desc_count(info->rbufs[i], count); 2145 set_desc_status(info->rbufs[i], BIT15 | (reg >> 8)); 2146 info->rbuf_fill_count = count = 0; 2147 if (++i == info->rbuf_count) 2148 i = 0; 2149 info->pending_bh |= BH_RECEIVE; 2150 } 2151 } 2152 2153 info->rbuf_fill_index = i; 2154 info->rbuf_fill_count = count; 2155} 2156 2157static void isr_serial(struct slgt_info *info) 2158{ 2159 unsigned short status = rd_reg16(info, SSR); 2160 2161 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status)); 2162 2163 wr_reg16(info, SSR, status); /* clear pending */ 2164 2165 info->irq_occurred = true; 2166 2167 if (info->params.mode == MGSL_MODE_ASYNC) { 2168 if (status & IRQ_TXIDLE) { 2169 if (info->tx_active) 2170 isr_txeom(info, status); 2171 } 2172 if (info->rx_pio && (status & IRQ_RXDATA)) 2173 isr_rxdata(info); 2174 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) { 2175 info->icount.brk++; 2176 /* process break detection if tty control allows */ 2177 if (info->port.tty) { 2178 if (!(status & info->ignore_status_mask)) { 2179 if (info->read_status_mask & MASK_BREAK) { 2180 tty_insert_flip_char(&info->port, 0, TTY_BREAK); 2181 if (info->port.flags & ASYNC_SAK) 2182 do_SAK(info->port.tty); 2183 } 2184 } 2185 } 2186 } 2187 } else { 2188 if (status & (IRQ_TXIDLE + IRQ_TXUNDER)) 2189 isr_txeom(info, status); 2190 if (info->rx_pio && (status & IRQ_RXDATA)) 2191 isr_rxdata(info); 2192 if (status & IRQ_RXIDLE) { 2193 if (status & RXIDLE) 2194 info->icount.rxidle++; 2195 else 2196 info->icount.exithunt++; 2197 wake_up_interruptible(&info->event_wait_q); 2198 } 2199 2200 if (status & IRQ_RXOVER) 2201 rx_start(info); 2202 } 2203 2204 if (status & IRQ_DSR) 2205 dsr_change(info, status); 2206 if (status & IRQ_CTS) 2207 cts_change(info, status); 2208 if (status & IRQ_DCD) 2209 dcd_change(info, status); 2210 if (status & IRQ_RI) 2211 ri_change(info, status); 2212} 2213 2214static void isr_rdma(struct slgt_info *info) 2215{ 2216 unsigned int status = rd_reg32(info, RDCSR); 2217 2218 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status)); 2219 2220 /* RDCSR (rx DMA control/status) 2221 * 2222 * 31..07 reserved 2223 * 06 save status byte to DMA buffer 2224 * 05 error 2225 * 04 eol (end of list) 2226 * 03 eob (end of buffer) 2227 * 02 IRQ enable 2228 * 01 reset 2229 * 00 enable 2230 */ 2231 wr_reg32(info, RDCSR, status); /* clear pending */ 2232 2233 if (status & (BIT5 + BIT4)) { 2234 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name)); 2235 info->rx_restart = true; 2236 } 2237 info->pending_bh |= BH_RECEIVE; 2238} 2239 2240static void isr_tdma(struct slgt_info *info) 2241{ 2242 unsigned int status = rd_reg32(info, TDCSR); 2243 2244 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status)); 2245 2246 /* TDCSR (tx DMA control/status) 2247 * 2248 * 31..06 reserved 2249 * 05 error 2250 * 04 eol (end of list) 2251 * 03 eob (end of buffer) 2252 * 02 IRQ enable 2253 * 01 reset 2254 * 00 enable 2255 */ 2256 wr_reg32(info, TDCSR, status); /* clear pending */ 2257 2258 if (status & (BIT5 + BIT4 + BIT3)) { 2259 // another transmit buffer has completed 2260 // run bottom half to get more send data from user 2261 info->pending_bh |= BH_TRANSMIT; 2262 } 2263} 2264 2265/* 2266 * return true if there are unsent tx DMA buffers, otherwise false 2267 * 2268 * if there are unsent buffers then info->tbuf_start 2269 * is set to index of first unsent buffer 2270 */ 2271static bool unsent_tbufs(struct slgt_info *info) 2272{ 2273 unsigned int i = info->tbuf_current; 2274 bool rc = false; 2275 2276 /* 2277 * search backwards from last loaded buffer (precedes tbuf_current) 2278 * for first unsent buffer (desc_count > 0) 2279 */ 2280 2281 do { 2282 if (i) 2283 i--; 2284 else 2285 i = info->tbuf_count - 1; 2286 if (!desc_count(info->tbufs[i])) 2287 break; 2288 info->tbuf_start = i; 2289 rc = true; 2290 } while (i != info->tbuf_current); 2291 2292 return rc; 2293} 2294 2295static void isr_txeom(struct slgt_info *info, unsigned short status) 2296{ 2297 DBGISR(("%s txeom status=%04x\n", info->device_name, status)); 2298 2299 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER); 2300 tdma_reset(info); 2301 if (status & IRQ_TXUNDER) { 2302 unsigned short val = rd_reg16(info, TCR); 2303 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */ 2304 wr_reg16(info, TCR, val); /* clear reset bit */ 2305 } 2306 2307 if (info->tx_active) { 2308 if (info->params.mode != MGSL_MODE_ASYNC) { 2309 if (status & IRQ_TXUNDER) 2310 info->icount.txunder++; 2311 else if (status & IRQ_TXIDLE) 2312 info->icount.txok++; 2313 } 2314 2315 if (unsent_tbufs(info)) { 2316 tx_start(info); 2317 update_tx_timer(info); 2318 return; 2319 } 2320 info->tx_active = false; 2321 2322 del_timer(&info->tx_timer); 2323 2324 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) { 2325 info->signals &= ~SerialSignal_RTS; 2326 info->drop_rts_on_tx_done = false; 2327 set_signals(info); 2328 } 2329 2330#if SYNCLINK_GENERIC_HDLC 2331 if (info->netcount) 2332 hdlcdev_tx_done(info); 2333 else 2334#endif 2335 { 2336 if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) { 2337 tx_stop(info); 2338 return; 2339 } 2340 info->pending_bh |= BH_TRANSMIT; 2341 } 2342 } 2343} 2344 2345static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state) 2346{ 2347 struct cond_wait *w, *prev; 2348 2349 /* wake processes waiting for specific transitions */ 2350 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) { 2351 if (w->data & changed) { 2352 w->data = state; 2353 wake_up_interruptible(&w->q); 2354 if (prev != NULL) 2355 prev->next = w->next; 2356 else 2357 info->gpio_wait_q = w->next; 2358 } else 2359 prev = w; 2360 } 2361} 2362 2363/* interrupt service routine 2364 * 2365 * irq interrupt number 2366 * dev_id device ID supplied during interrupt registration 2367 */ 2368static irqreturn_t slgt_interrupt(int dummy, void *dev_id) 2369{ 2370 struct slgt_info *info = dev_id; 2371 unsigned int gsr; 2372 unsigned int i; 2373 2374 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level)); 2375 2376 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) { 2377 DBGISR(("%s gsr=%08x\n", info->device_name, gsr)); 2378 info->irq_occurred = true; 2379 for(i=0; i < info->port_count ; i++) { 2380 if (info->port_array[i] == NULL) 2381 continue; 2382 spin_lock(&info->port_array[i]->lock); 2383 if (gsr & (BIT8 << i)) 2384 isr_serial(info->port_array[i]); 2385 if (gsr & (BIT16 << (i*2))) 2386 isr_rdma(info->port_array[i]); 2387 if (gsr & (BIT17 << (i*2))) 2388 isr_tdma(info->port_array[i]); 2389 spin_unlock(&info->port_array[i]->lock); 2390 } 2391 } 2392 2393 if (info->gpio_present) { 2394 unsigned int state; 2395 unsigned int changed; 2396 spin_lock(&info->lock); 2397 while ((changed = rd_reg32(info, IOSR)) != 0) { 2398 DBGISR(("%s iosr=%08x\n", info->device_name, changed)); 2399 /* read latched state of GPIO signals */ 2400 state = rd_reg32(info, IOVR); 2401 /* clear pending GPIO interrupt bits */ 2402 wr_reg32(info, IOSR, changed); 2403 for (i=0 ; i < info->port_count ; i++) { 2404 if (info->port_array[i] != NULL) 2405 isr_gpio(info->port_array[i], changed, state); 2406 } 2407 } 2408 spin_unlock(&info->lock); 2409 } 2410 2411 for(i=0; i < info->port_count ; i++) { 2412 struct slgt_info *port = info->port_array[i]; 2413 if (port == NULL) 2414 continue; 2415 spin_lock(&port->lock); 2416 if ((port->port.count || port->netcount) && 2417 port->pending_bh && !port->bh_running && 2418 !port->bh_requested) { 2419 DBGISR(("%s bh queued\n", port->device_name)); 2420 schedule_work(&port->task); 2421 port->bh_requested = true; 2422 } 2423 spin_unlock(&port->lock); 2424 } 2425 2426 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level)); 2427 return IRQ_HANDLED; 2428} 2429 2430static int startup(struct slgt_info *info) 2431{ 2432 DBGINFO(("%s startup\n", info->device_name)); 2433 2434 if (info->port.flags & ASYNC_INITIALIZED) 2435 return 0; 2436 2437 if (!info->tx_buf) { 2438 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL); 2439 if (!info->tx_buf) { 2440 DBGERR(("%s can't allocate tx buffer\n", info->device_name)); 2441 return -ENOMEM; 2442 } 2443 } 2444 2445 info->pending_bh = 0; 2446 2447 memset(&info->icount, 0, sizeof(info->icount)); 2448 2449 /* program hardware for current parameters */ 2450 change_params(info); 2451 2452 if (info->port.tty) 2453 clear_bit(TTY_IO_ERROR, &info->port.tty->flags); 2454 2455 info->port.flags |= ASYNC_INITIALIZED; 2456 2457 return 0; 2458} 2459 2460/* 2461 * called by close() and hangup() to shutdown hardware 2462 */ 2463static void shutdown(struct slgt_info *info) 2464{ 2465 unsigned long flags; 2466 2467 if (!(info->port.flags & ASYNC_INITIALIZED)) 2468 return; 2469 2470 DBGINFO(("%s shutdown\n", info->device_name)); 2471 2472 /* clear status wait queue because status changes */ 2473 /* can't happen after shutting down the hardware */ 2474 wake_up_interruptible(&info->status_event_wait_q); 2475 wake_up_interruptible(&info->event_wait_q); 2476 2477 del_timer_sync(&info->tx_timer); 2478 del_timer_sync(&info->rx_timer); 2479 2480 kfree(info->tx_buf); 2481 info->tx_buf = NULL; 2482 2483 spin_lock_irqsave(&info->lock,flags); 2484 2485 tx_stop(info); 2486 rx_stop(info); 2487 2488 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 2489 2490 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) { 2491 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 2492 set_signals(info); 2493 } 2494 2495 flush_cond_wait(&info->gpio_wait_q); 2496 2497 spin_unlock_irqrestore(&info->lock,flags); 2498 2499 if (info->port.tty) 2500 set_bit(TTY_IO_ERROR, &info->port.tty->flags); 2501 2502 info->port.flags &= ~ASYNC_INITIALIZED; 2503} 2504 2505static void program_hw(struct slgt_info *info) 2506{ 2507 unsigned long flags; 2508 2509 spin_lock_irqsave(&info->lock,flags); 2510 2511 rx_stop(info); 2512 tx_stop(info); 2513 2514 if (info->params.mode != MGSL_MODE_ASYNC || 2515 info->netcount) 2516 sync_mode(info); 2517 else 2518 async_mode(info); 2519 2520 set_signals(info); 2521 2522 info->dcd_chkcount = 0; 2523 info->cts_chkcount = 0; 2524 info->ri_chkcount = 0; 2525 info->dsr_chkcount = 0; 2526 2527 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI); 2528 get_signals(info); 2529 2530 if (info->netcount || 2531 (info->port.tty && info->port.tty->termios.c_cflag & CREAD)) 2532 rx_start(info); 2533 2534 spin_unlock_irqrestore(&info->lock,flags); 2535} 2536 2537/* 2538 * reconfigure adapter based on new parameters 2539 */ 2540static void change_params(struct slgt_info *info) 2541{ 2542 unsigned cflag; 2543 int bits_per_char; 2544 2545 if (!info->port.tty) 2546 return; 2547 DBGINFO(("%s change_params\n", info->device_name)); 2548 2549 cflag = info->port.tty->termios.c_cflag; 2550 2551 /* if B0 rate (hangup) specified then negate RTS and DTR */ 2552 /* otherwise assert RTS and DTR */ 2553 if (cflag & CBAUD) 2554 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 2555 else 2556 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 2557 2558 /* byte size and parity */ 2559 2560 switch (cflag & CSIZE) { 2561 case CS5: info->params.data_bits = 5; break; 2562 case CS6: info->params.data_bits = 6; break; 2563 case CS7: info->params.data_bits = 7; break; 2564 case CS8: info->params.data_bits = 8; break; 2565 default: info->params.data_bits = 7; break; 2566 } 2567 2568 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1; 2569 2570 if (cflag & PARENB) 2571 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN; 2572 else 2573 info->params.parity = ASYNC_PARITY_NONE; 2574 2575 /* calculate number of jiffies to transmit a full 2576 * FIFO (32 bytes) at specified data rate 2577 */ 2578 bits_per_char = info->params.data_bits + 2579 info->params.stop_bits + 1; 2580 2581 info->params.data_rate = tty_get_baud_rate(info->port.tty); 2582 2583 if (info->params.data_rate) { 2584 info->timeout = (32*HZ*bits_per_char) / 2585 info->params.data_rate; 2586 } 2587 info->timeout += HZ/50; /* Add .02 seconds of slop */ 2588 2589 if (cflag & CRTSCTS) 2590 info->port.flags |= ASYNC_CTS_FLOW; 2591 else 2592 info->port.flags &= ~ASYNC_CTS_FLOW; 2593 2594 if (cflag & CLOCAL) 2595 info->port.flags &= ~ASYNC_CHECK_CD; 2596 else 2597 info->port.flags |= ASYNC_CHECK_CD; 2598 2599 /* process tty input control flags */ 2600 2601 info->read_status_mask = IRQ_RXOVER; 2602 if (I_INPCK(info->port.tty)) 2603 info->read_status_mask |= MASK_PARITY | MASK_FRAMING; 2604 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty)) 2605 info->read_status_mask |= MASK_BREAK; 2606 if (I_IGNPAR(info->port.tty)) 2607 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING; 2608 if (I_IGNBRK(info->port.tty)) { 2609 info->ignore_status_mask |= MASK_BREAK; 2610 /* If ignoring parity and break indicators, ignore 2611 * overruns too. (For real raw support). 2612 */ 2613 if (I_IGNPAR(info->port.tty)) 2614 info->ignore_status_mask |= MASK_OVERRUN; 2615 } 2616 2617 program_hw(info); 2618} 2619 2620static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount) 2621{ 2622 DBGINFO(("%s get_stats\n", info->device_name)); 2623 if (!user_icount) { 2624 memset(&info->icount, 0, sizeof(info->icount)); 2625 } else { 2626 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount))) 2627 return -EFAULT; 2628 } 2629 return 0; 2630} 2631 2632static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params) 2633{ 2634 DBGINFO(("%s get_params\n", info->device_name)); 2635 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS))) 2636 return -EFAULT; 2637 return 0; 2638} 2639 2640static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params) 2641{ 2642 unsigned long flags; 2643 MGSL_PARAMS tmp_params; 2644 2645 DBGINFO(("%s set_params\n", info->device_name)); 2646 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS))) 2647 return -EFAULT; 2648 2649 spin_lock_irqsave(&info->lock, flags); 2650 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) 2651 info->base_clock = tmp_params.clock_speed; 2652 else 2653 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS)); 2654 spin_unlock_irqrestore(&info->lock, flags); 2655 2656 program_hw(info); 2657 2658 return 0; 2659} 2660 2661static int get_txidle(struct slgt_info *info, int __user *idle_mode) 2662{ 2663 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode)); 2664 if (put_user(info->idle_mode, idle_mode)) 2665 return -EFAULT; 2666 return 0; 2667} 2668 2669static int set_txidle(struct slgt_info *info, int idle_mode) 2670{ 2671 unsigned long flags; 2672 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode)); 2673 spin_lock_irqsave(&info->lock,flags); 2674 info->idle_mode = idle_mode; 2675 if (info->params.mode != MGSL_MODE_ASYNC) 2676 tx_set_idle(info); 2677 spin_unlock_irqrestore(&info->lock,flags); 2678 return 0; 2679} 2680 2681static int tx_enable(struct slgt_info *info, int enable) 2682{ 2683 unsigned long flags; 2684 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable)); 2685 spin_lock_irqsave(&info->lock,flags); 2686 if (enable) { 2687 if (!info->tx_enabled) 2688 tx_start(info); 2689 } else { 2690 if (info->tx_enabled) 2691 tx_stop(info); 2692 } 2693 spin_unlock_irqrestore(&info->lock,flags); 2694 return 0; 2695} 2696 2697/* 2698 * abort transmit HDLC frame 2699 */ 2700static int tx_abort(struct slgt_info *info) 2701{ 2702 unsigned long flags; 2703 DBGINFO(("%s tx_abort\n", info->device_name)); 2704 spin_lock_irqsave(&info->lock,flags); 2705 tdma_reset(info); 2706 spin_unlock_irqrestore(&info->lock,flags); 2707 return 0; 2708} 2709 2710static int rx_enable(struct slgt_info *info, int enable) 2711{ 2712 unsigned long flags; 2713 unsigned int rbuf_fill_level; 2714 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable)); 2715 spin_lock_irqsave(&info->lock,flags); 2716 /* 2717 * enable[31..16] = receive DMA buffer fill level 2718 * 0 = noop (leave fill level unchanged) 2719 * fill level must be multiple of 4 and <= buffer size 2720 */ 2721 rbuf_fill_level = ((unsigned int)enable) >> 16; 2722 if (rbuf_fill_level) { 2723 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) { 2724 spin_unlock_irqrestore(&info->lock, flags); 2725 return -EINVAL; 2726 } 2727 info->rbuf_fill_level = rbuf_fill_level; 2728 if (rbuf_fill_level < 128) 2729 info->rx_pio = 1; /* PIO mode */ 2730 else 2731 info->rx_pio = 0; /* DMA mode */ 2732 rx_stop(info); /* restart receiver to use new fill level */ 2733 } 2734 2735 /* 2736 * enable[1..0] = receiver enable command 2737 * 0 = disable 2738 * 1 = enable 2739 * 2 = enable or force hunt mode if already enabled 2740 */ 2741 enable &= 3; 2742 if (enable) { 2743 if (!info->rx_enabled) 2744 rx_start(info); 2745 else if (enable == 2) { 2746 /* force hunt mode (write 1 to RCR[3]) */ 2747 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3); 2748 } 2749 } else { 2750 if (info->rx_enabled) 2751 rx_stop(info); 2752 } 2753 spin_unlock_irqrestore(&info->lock,flags); 2754 return 0; 2755} 2756 2757/* 2758 * wait for specified event to occur 2759 */ 2760static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr) 2761{ 2762 unsigned long flags; 2763 int s; 2764 int rc=0; 2765 struct mgsl_icount cprev, cnow; 2766 int events; 2767 int mask; 2768 struct _input_signal_events oldsigs, newsigs; 2769 DECLARE_WAITQUEUE(wait, current); 2770 2771 if (get_user(mask, mask_ptr)) 2772 return -EFAULT; 2773 2774 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask)); 2775 2776 spin_lock_irqsave(&info->lock,flags); 2777 2778 /* return immediately if state matches requested events */ 2779 get_signals(info); 2780 s = info->signals; 2781 2782 events = mask & 2783 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) + 2784 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) + 2785 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) + 2786 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) ); 2787 if (events) { 2788 spin_unlock_irqrestore(&info->lock,flags); 2789 goto exit; 2790 } 2791 2792 /* save current irq counts */ 2793 cprev = info->icount; 2794 oldsigs = info->input_signal_events; 2795 2796 /* enable hunt and idle irqs if needed */ 2797 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) { 2798 unsigned short val = rd_reg16(info, SCR); 2799 if (!(val & IRQ_RXIDLE)) 2800 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE)); 2801 } 2802 2803 set_current_state(TASK_INTERRUPTIBLE); 2804 add_wait_queue(&info->event_wait_q, &wait); 2805 2806 spin_unlock_irqrestore(&info->lock,flags); 2807 2808 for(;;) { 2809 schedule(); 2810 if (signal_pending(current)) { 2811 rc = -ERESTARTSYS; 2812 break; 2813 } 2814 2815 /* get current irq counts */ 2816 spin_lock_irqsave(&info->lock,flags); 2817 cnow = info->icount; 2818 newsigs = info->input_signal_events; 2819 set_current_state(TASK_INTERRUPTIBLE); 2820 spin_unlock_irqrestore(&info->lock,flags); 2821 2822 /* if no change, wait aborted for some reason */ 2823 if (newsigs.dsr_up == oldsigs.dsr_up && 2824 newsigs.dsr_down == oldsigs.dsr_down && 2825 newsigs.dcd_up == oldsigs.dcd_up && 2826 newsigs.dcd_down == oldsigs.dcd_down && 2827 newsigs.cts_up == oldsigs.cts_up && 2828 newsigs.cts_down == oldsigs.cts_down && 2829 newsigs.ri_up == oldsigs.ri_up && 2830 newsigs.ri_down == oldsigs.ri_down && 2831 cnow.exithunt == cprev.exithunt && 2832 cnow.rxidle == cprev.rxidle) { 2833 rc = -EIO; 2834 break; 2835 } 2836 2837 events = mask & 2838 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) + 2839 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) + 2840 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) + 2841 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) + 2842 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) + 2843 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) + 2844 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) + 2845 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) + 2846 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) + 2847 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) ); 2848 if (events) 2849 break; 2850 2851 cprev = cnow; 2852 oldsigs = newsigs; 2853 } 2854 2855 remove_wait_queue(&info->event_wait_q, &wait); 2856 set_current_state(TASK_RUNNING); 2857 2858 2859 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) { 2860 spin_lock_irqsave(&info->lock,flags); 2861 if (!waitqueue_active(&info->event_wait_q)) { 2862 /* disable enable exit hunt mode/idle rcvd IRQs */ 2863 wr_reg16(info, SCR, 2864 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE)); 2865 } 2866 spin_unlock_irqrestore(&info->lock,flags); 2867 } 2868exit: 2869 if (rc == 0) 2870 rc = put_user(events, mask_ptr); 2871 return rc; 2872} 2873 2874static int get_interface(struct slgt_info *info, int __user *if_mode) 2875{ 2876 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode)); 2877 if (put_user(info->if_mode, if_mode)) 2878 return -EFAULT; 2879 return 0; 2880} 2881 2882static int set_interface(struct slgt_info *info, int if_mode) 2883{ 2884 unsigned long flags; 2885 unsigned short val; 2886 2887 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode)); 2888 spin_lock_irqsave(&info->lock,flags); 2889 info->if_mode = if_mode; 2890 2891 msc_set_vcr(info); 2892 2893 /* TCR (tx control) 07 1=RTS driver control */ 2894 val = rd_reg16(info, TCR); 2895 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 2896 val |= BIT7; 2897 else 2898 val &= ~BIT7; 2899 wr_reg16(info, TCR, val); 2900 2901 spin_unlock_irqrestore(&info->lock,flags); 2902 return 0; 2903} 2904 2905static int get_xsync(struct slgt_info *info, int __user *xsync) 2906{ 2907 DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync)); 2908 if (put_user(info->xsync, xsync)) 2909 return -EFAULT; 2910 return 0; 2911} 2912 2913/* 2914 * set extended sync pattern (1 to 4 bytes) for extended sync mode 2915 * 2916 * sync pattern is contained in least significant bytes of value 2917 * most significant byte of sync pattern is oldest (1st sent/detected) 2918 */ 2919static int set_xsync(struct slgt_info *info, int xsync) 2920{ 2921 unsigned long flags; 2922 2923 DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync)); 2924 spin_lock_irqsave(&info->lock, flags); 2925 info->xsync = xsync; 2926 wr_reg32(info, XSR, xsync); 2927 spin_unlock_irqrestore(&info->lock, flags); 2928 return 0; 2929} 2930 2931static int get_xctrl(struct slgt_info *info, int __user *xctrl) 2932{ 2933 DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl)); 2934 if (put_user(info->xctrl, xctrl)) 2935 return -EFAULT; 2936 return 0; 2937} 2938 2939/* 2940 * set extended control options 2941 * 2942 * xctrl[31:19] reserved, must be zero 2943 * xctrl[18:17] extended sync pattern length in bytes 2944 * 00 = 1 byte in xsr[7:0] 2945 * 01 = 2 bytes in xsr[15:0] 2946 * 10 = 3 bytes in xsr[23:0] 2947 * 11 = 4 bytes in xsr[31:0] 2948 * xctrl[16] 1 = enable terminal count, 0=disabled 2949 * xctrl[15:0] receive terminal count for fixed length packets 2950 * value is count minus one (0 = 1 byte packet) 2951 * when terminal count is reached, receiver 2952 * automatically returns to hunt mode and receive 2953 * FIFO contents are flushed to DMA buffers with 2954 * end of frame (EOF) status 2955 */ 2956static int set_xctrl(struct slgt_info *info, int xctrl) 2957{ 2958 unsigned long flags; 2959 2960 DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl)); 2961 spin_lock_irqsave(&info->lock, flags); 2962 info->xctrl = xctrl; 2963 wr_reg32(info, XCR, xctrl); 2964 spin_unlock_irqrestore(&info->lock, flags); 2965 return 0; 2966} 2967 2968/* 2969 * set general purpose IO pin state and direction 2970 * 2971 * user_gpio fields: 2972 * state each bit indicates a pin state 2973 * smask set bit indicates pin state to set 2974 * dir each bit indicates a pin direction (0=input, 1=output) 2975 * dmask set bit indicates pin direction to set 2976 */ 2977static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 2978{ 2979 unsigned long flags; 2980 struct gpio_desc gpio; 2981 __u32 data; 2982 2983 if (!info->gpio_present) 2984 return -EINVAL; 2985 if (copy_from_user(&gpio, user_gpio, sizeof(gpio))) 2986 return -EFAULT; 2987 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n", 2988 info->device_name, gpio.state, gpio.smask, 2989 gpio.dir, gpio.dmask)); 2990 2991 spin_lock_irqsave(&info->port_array[0]->lock, flags); 2992 if (gpio.dmask) { 2993 data = rd_reg32(info, IODR); 2994 data |= gpio.dmask & gpio.dir; 2995 data &= ~(gpio.dmask & ~gpio.dir); 2996 wr_reg32(info, IODR, data); 2997 } 2998 if (gpio.smask) { 2999 data = rd_reg32(info, IOVR); 3000 data |= gpio.smask & gpio.state; 3001 data &= ~(gpio.smask & ~gpio.state); 3002 wr_reg32(info, IOVR, data); 3003 } 3004 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 3005 3006 return 0; 3007} 3008 3009/* 3010 * get general purpose IO pin state and direction 3011 */ 3012static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 3013{ 3014 struct gpio_desc gpio; 3015 if (!info->gpio_present) 3016 return -EINVAL; 3017 gpio.state = rd_reg32(info, IOVR); 3018 gpio.smask = 0xffffffff; 3019 gpio.dir = rd_reg32(info, IODR); 3020 gpio.dmask = 0xffffffff; 3021 if (copy_to_user(user_gpio, &gpio, sizeof(gpio))) 3022 return -EFAULT; 3023 DBGINFO(("%s get_gpio state=%08x dir=%08x\n", 3024 info->device_name, gpio.state, gpio.dir)); 3025 return 0; 3026} 3027 3028/* 3029 * conditional wait facility 3030 */ 3031static void init_cond_wait(struct cond_wait *w, unsigned int data) 3032{ 3033 init_waitqueue_head(&w->q); 3034 init_waitqueue_entry(&w->wait, current); 3035 w->data = data; 3036} 3037 3038static void add_cond_wait(struct cond_wait **head, struct cond_wait *w) 3039{ 3040 set_current_state(TASK_INTERRUPTIBLE); 3041 add_wait_queue(&w->q, &w->wait); 3042 w->next = *head; 3043 *head = w; 3044} 3045 3046static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw) 3047{ 3048 struct cond_wait *w, *prev; 3049 remove_wait_queue(&cw->q, &cw->wait); 3050 set_current_state(TASK_RUNNING); 3051 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) { 3052 if (w == cw) { 3053 if (prev != NULL) 3054 prev->next = w->next; 3055 else 3056 *head = w->next; 3057 break; 3058 } 3059 } 3060} 3061 3062static void flush_cond_wait(struct cond_wait **head) 3063{ 3064 while (*head != NULL) { 3065 wake_up_interruptible(&(*head)->q); 3066 *head = (*head)->next; 3067 } 3068} 3069 3070/* 3071 * wait for general purpose I/O pin(s) to enter specified state 3072 * 3073 * user_gpio fields: 3074 * state - bit indicates target pin state 3075 * smask - set bit indicates watched pin 3076 * 3077 * The wait ends when at least one watched pin enters the specified 3078 * state. When 0 (no error) is returned, user_gpio->state is set to the 3079 * state of all GPIO pins when the wait ends. 3080 * 3081 * Note: Each pin may be a dedicated input, dedicated output, or 3082 * configurable input/output. The number and configuration of pins 3083 * varies with the specific adapter model. Only input pins (dedicated 3084 * or configured) can be monitored with this function. 3085 */ 3086static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio) 3087{ 3088 unsigned long flags; 3089 int rc = 0; 3090 struct gpio_desc gpio; 3091 struct cond_wait wait; 3092 u32 state; 3093 3094 if (!info->gpio_present) 3095 return -EINVAL; 3096 if (copy_from_user(&gpio, user_gpio, sizeof(gpio))) 3097 return -EFAULT; 3098 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n", 3099 info->device_name, gpio.state, gpio.smask)); 3100 /* ignore output pins identified by set IODR bit */ 3101 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0) 3102 return -EINVAL; 3103 init_cond_wait(&wait, gpio.smask); 3104 3105 spin_lock_irqsave(&info->port_array[0]->lock, flags); 3106 /* enable interrupts for watched pins */ 3107 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask); 3108 /* get current pin states */ 3109 state = rd_reg32(info, IOVR); 3110 3111 if (gpio.smask & ~(state ^ gpio.state)) { 3112 /* already in target state */ 3113 gpio.state = state; 3114 } else { 3115 /* wait for target state */ 3116 add_cond_wait(&info->gpio_wait_q, &wait); 3117 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 3118 schedule(); 3119 if (signal_pending(current)) 3120 rc = -ERESTARTSYS; 3121 else 3122 gpio.state = wait.data; 3123 spin_lock_irqsave(&info->port_array[0]->lock, flags); 3124 remove_cond_wait(&info->gpio_wait_q, &wait); 3125 } 3126 3127 /* disable all GPIO interrupts if no waiting processes */ 3128 if (info->gpio_wait_q == NULL) 3129 wr_reg32(info, IOER, 0); 3130 spin_unlock_irqrestore(&info->port_array[0]->lock, flags); 3131 3132 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio))) 3133 rc = -EFAULT; 3134 return rc; 3135} 3136 3137static int modem_input_wait(struct slgt_info *info,int arg) 3138{ 3139 unsigned long flags; 3140 int rc; 3141 struct mgsl_icount cprev, cnow; 3142 DECLARE_WAITQUEUE(wait, current); 3143 3144 /* save current irq counts */ 3145 spin_lock_irqsave(&info->lock,flags); 3146 cprev = info->icount; 3147 add_wait_queue(&info->status_event_wait_q, &wait); 3148 set_current_state(TASK_INTERRUPTIBLE); 3149 spin_unlock_irqrestore(&info->lock,flags); 3150 3151 for(;;) { 3152 schedule(); 3153 if (signal_pending(current)) { 3154 rc = -ERESTARTSYS; 3155 break; 3156 } 3157 3158 /* get new irq counts */ 3159 spin_lock_irqsave(&info->lock,flags); 3160 cnow = info->icount; 3161 set_current_state(TASK_INTERRUPTIBLE); 3162 spin_unlock_irqrestore(&info->lock,flags); 3163 3164 /* if no change, wait aborted for some reason */ 3165 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr && 3166 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) { 3167 rc = -EIO; 3168 break; 3169 } 3170 3171 /* check for change in caller specified modem input */ 3172 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) || 3173 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) || 3174 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) || 3175 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) { 3176 rc = 0; 3177 break; 3178 } 3179 3180 cprev = cnow; 3181 } 3182 remove_wait_queue(&info->status_event_wait_q, &wait); 3183 set_current_state(TASK_RUNNING); 3184 return rc; 3185} 3186 3187/* 3188 * return state of serial control and status signals 3189 */ 3190static int tiocmget(struct tty_struct *tty) 3191{ 3192 struct slgt_info *info = tty->driver_data; 3193 unsigned int result; 3194 unsigned long flags; 3195 3196 spin_lock_irqsave(&info->lock,flags); 3197 get_signals(info); 3198 spin_unlock_irqrestore(&info->lock,flags); 3199 3200 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) + 3201 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) + 3202 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) + 3203 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) + 3204 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) + 3205 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0); 3206 3207 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result)); 3208 return result; 3209} 3210 3211/* 3212 * set modem control signals (DTR/RTS) 3213 * 3214 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit 3215 * TIOCMSET = set/clear signal values 3216 * value bit mask for command 3217 */ 3218static int tiocmset(struct tty_struct *tty, 3219 unsigned int set, unsigned int clear) 3220{ 3221 struct slgt_info *info = tty->driver_data; 3222 unsigned long flags; 3223 3224 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear)); 3225 3226 if (set & TIOCM_RTS) 3227 info->signals |= SerialSignal_RTS; 3228 if (set & TIOCM_DTR) 3229 info->signals |= SerialSignal_DTR; 3230 if (clear & TIOCM_RTS) 3231 info->signals &= ~SerialSignal_RTS; 3232 if (clear & TIOCM_DTR) 3233 info->signals &= ~SerialSignal_DTR; 3234 3235 spin_lock_irqsave(&info->lock,flags); 3236 set_signals(info); 3237 spin_unlock_irqrestore(&info->lock,flags); 3238 return 0; 3239} 3240 3241static int carrier_raised(struct tty_port *port) 3242{ 3243 unsigned long flags; 3244 struct slgt_info *info = container_of(port, struct slgt_info, port); 3245 3246 spin_lock_irqsave(&info->lock,flags); 3247 get_signals(info); 3248 spin_unlock_irqrestore(&info->lock,flags); 3249 return (info->signals & SerialSignal_DCD) ? 1 : 0; 3250} 3251 3252static void dtr_rts(struct tty_port *port, int on) 3253{ 3254 unsigned long flags; 3255 struct slgt_info *info = container_of(port, struct slgt_info, port); 3256 3257 spin_lock_irqsave(&info->lock,flags); 3258 if (on) 3259 info->signals |= SerialSignal_RTS | SerialSignal_DTR; 3260 else 3261 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 3262 set_signals(info); 3263 spin_unlock_irqrestore(&info->lock,flags); 3264} 3265 3266 3267/* 3268 * block current process until the device is ready to open 3269 */ 3270static int block_til_ready(struct tty_struct *tty, struct file *filp, 3271 struct slgt_info *info) 3272{ 3273 DECLARE_WAITQUEUE(wait, current); 3274 int retval; 3275 bool do_clocal = false; 3276 unsigned long flags; 3277 int cd; 3278 struct tty_port *port = &info->port; 3279 3280 DBGINFO(("%s block_til_ready\n", tty->driver->name)); 3281 3282 if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){ 3283 /* nonblock mode is set or port is not enabled */ 3284 port->flags |= ASYNC_NORMAL_ACTIVE; 3285 return 0; 3286 } 3287 3288 if (tty->termios.c_cflag & CLOCAL) 3289 do_clocal = true; 3290 3291 /* Wait for carrier detect and the line to become 3292 * free (i.e., not in use by the callout). While we are in 3293 * this loop, port->count is dropped by one, so that 3294 * close() knows when to free things. We restore it upon 3295 * exit, either normal or abnormal. 3296 */ 3297 3298 retval = 0; 3299 add_wait_queue(&port->open_wait, &wait); 3300 3301 spin_lock_irqsave(&info->lock, flags); 3302 port->count--; 3303 spin_unlock_irqrestore(&info->lock, flags); 3304 port->blocked_open++; 3305 3306 while (1) { 3307 if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags)) 3308 tty_port_raise_dtr_rts(port); 3309 3310 set_current_state(TASK_INTERRUPTIBLE); 3311 3312 if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){ 3313 retval = (port->flags & ASYNC_HUP_NOTIFY) ? 3314 -EAGAIN : -ERESTARTSYS; 3315 break; 3316 } 3317 3318 cd = tty_port_carrier_raised(port); 3319 3320 if (!(port->flags & ASYNC_CLOSING) && (do_clocal || cd )) 3321 break; 3322 3323 if (signal_pending(current)) { 3324 retval = -ERESTARTSYS; 3325 break; 3326 } 3327 3328 DBGINFO(("%s block_til_ready wait\n", tty->driver->name)); 3329 tty_unlock(tty); 3330 schedule(); 3331 tty_lock(tty); 3332 } 3333 3334 set_current_state(TASK_RUNNING); 3335 remove_wait_queue(&port->open_wait, &wait); 3336 3337 if (!tty_hung_up_p(filp)) 3338 port->count++; 3339 port->blocked_open--; 3340 3341 if (!retval) 3342 port->flags |= ASYNC_NORMAL_ACTIVE; 3343 3344 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval)); 3345 return retval; 3346} 3347 3348/* 3349 * allocate buffers used for calling line discipline receive_buf 3350 * directly in synchronous mode 3351 * note: add 5 bytes to max frame size to allow appending 3352 * 32-bit CRC and status byte when configured to do so 3353 */ 3354static int alloc_tmp_rbuf(struct slgt_info *info) 3355{ 3356 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL); 3357 if (info->tmp_rbuf == NULL) 3358 return -ENOMEM; 3359 /* unused flag buffer to satisfy receive_buf calling interface */ 3360 info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL); 3361 if (!info->flag_buf) { 3362 kfree(info->tmp_rbuf); 3363 info->tmp_rbuf = NULL; 3364 return -ENOMEM; 3365 } 3366 return 0; 3367} 3368 3369static void free_tmp_rbuf(struct slgt_info *info) 3370{ 3371 kfree(info->tmp_rbuf); 3372 info->tmp_rbuf = NULL; 3373 kfree(info->flag_buf); 3374 info->flag_buf = NULL; 3375} 3376 3377/* 3378 * allocate DMA descriptor lists. 3379 */ 3380static int alloc_desc(struct slgt_info *info) 3381{ 3382 unsigned int i; 3383 unsigned int pbufs; 3384 3385 /* allocate memory to hold descriptor lists */ 3386 info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE, 3387 &info->bufs_dma_addr); 3388 if (info->bufs == NULL) 3389 return -ENOMEM; 3390 3391 info->rbufs = (struct slgt_desc*)info->bufs; 3392 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count; 3393 3394 pbufs = (unsigned int)info->bufs_dma_addr; 3395 3396 /* 3397 * Build circular lists of descriptors 3398 */ 3399 3400 for (i=0; i < info->rbuf_count; i++) { 3401 /* physical address of this descriptor */ 3402 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc)); 3403 3404 /* physical address of next descriptor */ 3405 if (i == info->rbuf_count - 1) 3406 info->rbufs[i].next = cpu_to_le32(pbufs); 3407 else 3408 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc))); 3409 set_desc_count(info->rbufs[i], DMABUFSIZE); 3410 } 3411 3412 for (i=0; i < info->tbuf_count; i++) { 3413 /* physical address of this descriptor */ 3414 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc)); 3415 3416 /* physical address of next descriptor */ 3417 if (i == info->tbuf_count - 1) 3418 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc)); 3419 else 3420 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc))); 3421 } 3422 3423 return 0; 3424} 3425 3426static void free_desc(struct slgt_info *info) 3427{ 3428 if (info->bufs != NULL) { 3429 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr); 3430 info->bufs = NULL; 3431 info->rbufs = NULL; 3432 info->tbufs = NULL; 3433 } 3434} 3435 3436static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count) 3437{ 3438 int i; 3439 for (i=0; i < count; i++) { 3440 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL) 3441 return -ENOMEM; 3442 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr); 3443 } 3444 return 0; 3445} 3446 3447static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count) 3448{ 3449 int i; 3450 for (i=0; i < count; i++) { 3451 if (bufs[i].buf == NULL) 3452 continue; 3453 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr); 3454 bufs[i].buf = NULL; 3455 } 3456} 3457 3458static int alloc_dma_bufs(struct slgt_info *info) 3459{ 3460 info->rbuf_count = 32; 3461 info->tbuf_count = 32; 3462 3463 if (alloc_desc(info) < 0 || 3464 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 || 3465 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 || 3466 alloc_tmp_rbuf(info) < 0) { 3467 DBGERR(("%s DMA buffer alloc fail\n", info->device_name)); 3468 return -ENOMEM; 3469 } 3470 reset_rbufs(info); 3471 return 0; 3472} 3473 3474static void free_dma_bufs(struct slgt_info *info) 3475{ 3476 if (info->bufs) { 3477 free_bufs(info, info->rbufs, info->rbuf_count); 3478 free_bufs(info, info->tbufs, info->tbuf_count); 3479 free_desc(info); 3480 } 3481 free_tmp_rbuf(info); 3482} 3483 3484static int claim_resources(struct slgt_info *info) 3485{ 3486 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) { 3487 DBGERR(("%s reg addr conflict, addr=%08X\n", 3488 info->device_name, info->phys_reg_addr)); 3489 info->init_error = DiagStatus_AddressConflict; 3490 goto errout; 3491 } 3492 else 3493 info->reg_addr_requested = true; 3494 3495 info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE); 3496 if (!info->reg_addr) { 3497 DBGERR(("%s can't map device registers, addr=%08X\n", 3498 info->device_name, info->phys_reg_addr)); 3499 info->init_error = DiagStatus_CantAssignPciResources; 3500 goto errout; 3501 } 3502 return 0; 3503 3504errout: 3505 release_resources(info); 3506 return -ENODEV; 3507} 3508 3509static void release_resources(struct slgt_info *info) 3510{ 3511 if (info->irq_requested) { 3512 free_irq(info->irq_level, info); 3513 info->irq_requested = false; 3514 } 3515 3516 if (info->reg_addr_requested) { 3517 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE); 3518 info->reg_addr_requested = false; 3519 } 3520 3521 if (info->reg_addr) { 3522 iounmap(info->reg_addr); 3523 info->reg_addr = NULL; 3524 } 3525} 3526 3527/* Add the specified device instance data structure to the 3528 * global linked list of devices and increment the device count. 3529 */ 3530static void add_device(struct slgt_info *info) 3531{ 3532 char *devstr; 3533 3534 info->next_device = NULL; 3535 info->line = slgt_device_count; 3536 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line); 3537 3538 if (info->line < MAX_DEVICES) { 3539 if (maxframe[info->line]) 3540 info->max_frame_size = maxframe[info->line]; 3541 } 3542 3543 slgt_device_count++; 3544 3545 if (!slgt_device_list) 3546 slgt_device_list = info; 3547 else { 3548 struct slgt_info *current_dev = slgt_device_list; 3549 while(current_dev->next_device) 3550 current_dev = current_dev->next_device; 3551 current_dev->next_device = info; 3552 } 3553 3554 if (info->max_frame_size < 4096) 3555 info->max_frame_size = 4096; 3556 else if (info->max_frame_size > 65535) 3557 info->max_frame_size = 65535; 3558 3559 switch(info->pdev->device) { 3560 case SYNCLINK_GT_DEVICE_ID: 3561 devstr = "GT"; 3562 break; 3563 case SYNCLINK_GT2_DEVICE_ID: 3564 devstr = "GT2"; 3565 break; 3566 case SYNCLINK_GT4_DEVICE_ID: 3567 devstr = "GT4"; 3568 break; 3569 case SYNCLINK_AC_DEVICE_ID: 3570 devstr = "AC"; 3571 info->params.mode = MGSL_MODE_ASYNC; 3572 break; 3573 default: 3574 devstr = "(unknown model)"; 3575 } 3576 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n", 3577 devstr, info->device_name, info->phys_reg_addr, 3578 info->irq_level, info->max_frame_size); 3579 3580#if SYNCLINK_GENERIC_HDLC 3581 hdlcdev_init(info); 3582#endif 3583} 3584 3585static const struct tty_port_operations slgt_port_ops = { 3586 .carrier_raised = carrier_raised, 3587 .dtr_rts = dtr_rts, 3588}; 3589 3590/* 3591 * allocate device instance structure, return NULL on failure 3592 */ 3593static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev) 3594{ 3595 struct slgt_info *info; 3596 3597 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL); 3598 3599 if (!info) { 3600 DBGERR(("%s device alloc failed adapter=%d port=%d\n", 3601 driver_name, adapter_num, port_num)); 3602 } else { 3603 tty_port_init(&info->port); 3604 info->port.ops = &slgt_port_ops; 3605 info->magic = MGSL_MAGIC; 3606 INIT_WORK(&info->task, bh_handler); 3607 info->max_frame_size = 4096; 3608 info->base_clock = 14745600; 3609 info->rbuf_fill_level = DMABUFSIZE; 3610 info->port.close_delay = 5*HZ/10; 3611 info->port.closing_wait = 30*HZ; 3612 init_waitqueue_head(&info->status_event_wait_q); 3613 init_waitqueue_head(&info->event_wait_q); 3614 spin_lock_init(&info->netlock); 3615 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS)); 3616 info->idle_mode = HDLC_TXIDLE_FLAGS; 3617 info->adapter_num = adapter_num; 3618 info->port_num = port_num; 3619 3620 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info); 3621 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info); 3622 3623 /* Copy configuration info to device instance data */ 3624 info->pdev = pdev; 3625 info->irq_level = pdev->irq; 3626 info->phys_reg_addr = pci_resource_start(pdev,0); 3627 3628 info->bus_type = MGSL_BUS_TYPE_PCI; 3629 info->irq_flags = IRQF_SHARED; 3630 3631 info->init_error = -1; /* assume error, set to 0 on successful init */ 3632 } 3633 3634 return info; 3635} 3636 3637static void device_init(int adapter_num, struct pci_dev *pdev) 3638{ 3639 struct slgt_info *port_array[SLGT_MAX_PORTS]; 3640 int i; 3641 int port_count = 1; 3642 3643 if (pdev->device == SYNCLINK_GT2_DEVICE_ID) 3644 port_count = 2; 3645 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID) 3646 port_count = 4; 3647 3648 /* allocate device instances for all ports */ 3649 for (i=0; i < port_count; ++i) { 3650 port_array[i] = alloc_dev(adapter_num, i, pdev); 3651 if (port_array[i] == NULL) { 3652 for (--i; i >= 0; --i) { 3653 tty_port_destroy(&port_array[i]->port); 3654 kfree(port_array[i]); 3655 } 3656 return; 3657 } 3658 } 3659 3660 /* give copy of port_array to all ports and add to device list */ 3661 for (i=0; i < port_count; ++i) { 3662 memcpy(port_array[i]->port_array, port_array, sizeof(port_array)); 3663 add_device(port_array[i]); 3664 port_array[i]->port_count = port_count; 3665 spin_lock_init(&port_array[i]->lock); 3666 } 3667 3668 /* Allocate and claim adapter resources */ 3669 if (!claim_resources(port_array[0])) { 3670 3671 alloc_dma_bufs(port_array[0]); 3672 3673 /* copy resource information from first port to others */ 3674 for (i = 1; i < port_count; ++i) { 3675 port_array[i]->irq_level = port_array[0]->irq_level; 3676 port_array[i]->reg_addr = port_array[0]->reg_addr; 3677 alloc_dma_bufs(port_array[i]); 3678 } 3679 3680 if (request_irq(port_array[0]->irq_level, 3681 slgt_interrupt, 3682 port_array[0]->irq_flags, 3683 port_array[0]->device_name, 3684 port_array[0]) < 0) { 3685 DBGERR(("%s request_irq failed IRQ=%d\n", 3686 port_array[0]->device_name, 3687 port_array[0]->irq_level)); 3688 } else { 3689 port_array[0]->irq_requested = true; 3690 adapter_test(port_array[0]); 3691 for (i=1 ; i < port_count ; i++) { 3692 port_array[i]->init_error = port_array[0]->init_error; 3693 port_array[i]->gpio_present = port_array[0]->gpio_present; 3694 } 3695 } 3696 } 3697 3698 for (i = 0; i < port_count; ++i) { 3699 struct slgt_info *info = port_array[i]; 3700 tty_port_register_device(&info->port, serial_driver, info->line, 3701 &info->pdev->dev); 3702 } 3703} 3704 3705static int init_one(struct pci_dev *dev, 3706 const struct pci_device_id *ent) 3707{ 3708 if (pci_enable_device(dev)) { 3709 printk("error enabling pci device %p\n", dev); 3710 return -EIO; 3711 } 3712 pci_set_master(dev); 3713 device_init(slgt_device_count, dev); 3714 return 0; 3715} 3716 3717static void remove_one(struct pci_dev *dev) 3718{ 3719} 3720 3721static const struct tty_operations ops = { 3722 .open = open, 3723 .close = close, 3724 .write = write, 3725 .put_char = put_char, 3726 .flush_chars = flush_chars, 3727 .write_room = write_room, 3728 .chars_in_buffer = chars_in_buffer, 3729 .flush_buffer = flush_buffer, 3730 .ioctl = ioctl, 3731 .compat_ioctl = slgt_compat_ioctl, 3732 .throttle = throttle, 3733 .unthrottle = unthrottle, 3734 .send_xchar = send_xchar, 3735 .break_ctl = set_break, 3736 .wait_until_sent = wait_until_sent, 3737 .set_termios = set_termios, 3738 .stop = tx_hold, 3739 .start = tx_release, 3740 .hangup = hangup, 3741 .tiocmget = tiocmget, 3742 .tiocmset = tiocmset, 3743 .get_icount = get_icount, 3744 .proc_fops = &synclink_gt_proc_fops, 3745}; 3746 3747static void slgt_cleanup(void) 3748{ 3749 int rc; 3750 struct slgt_info *info; 3751 struct slgt_info *tmp; 3752 3753 printk(KERN_INFO "unload %s\n", driver_name); 3754 3755 if (serial_driver) { 3756 for (info=slgt_device_list ; info != NULL ; info=info->next_device) 3757 tty_unregister_device(serial_driver, info->line); 3758 if ((rc = tty_unregister_driver(serial_driver))) 3759 DBGERR(("tty_unregister_driver error=%d\n", rc)); 3760 put_tty_driver(serial_driver); 3761 } 3762 3763 /* reset devices */ 3764 info = slgt_device_list; 3765 while(info) { 3766 reset_port(info); 3767 info = info->next_device; 3768 } 3769 3770 /* release devices */ 3771 info = slgt_device_list; 3772 while(info) { 3773#if SYNCLINK_GENERIC_HDLC 3774 hdlcdev_exit(info); 3775#endif 3776 free_dma_bufs(info); 3777 free_tmp_rbuf(info); 3778 if (info->port_num == 0) 3779 release_resources(info); 3780 tmp = info; 3781 info = info->next_device; 3782 tty_port_destroy(&tmp->port); 3783 kfree(tmp); 3784 } 3785 3786 if (pci_registered) 3787 pci_unregister_driver(&pci_driver); 3788} 3789 3790/* 3791 * Driver initialization entry point. 3792 */ 3793static int __init slgt_init(void) 3794{ 3795 int rc; 3796 3797 printk(KERN_INFO "%s\n", driver_name); 3798 3799 serial_driver = alloc_tty_driver(MAX_DEVICES); 3800 if (!serial_driver) { 3801 printk("%s can't allocate tty driver\n", driver_name); 3802 return -ENOMEM; 3803 } 3804 3805 /* Initialize the tty_driver structure */ 3806 3807 serial_driver->driver_name = tty_driver_name; 3808 serial_driver->name = tty_dev_prefix; 3809 serial_driver->major = ttymajor; 3810 serial_driver->minor_start = 64; 3811 serial_driver->type = TTY_DRIVER_TYPE_SERIAL; 3812 serial_driver->subtype = SERIAL_TYPE_NORMAL; 3813 serial_driver->init_termios = tty_std_termios; 3814 serial_driver->init_termios.c_cflag = 3815 B9600 | CS8 | CREAD | HUPCL | CLOCAL; 3816 serial_driver->init_termios.c_ispeed = 9600; 3817 serial_driver->init_termios.c_ospeed = 9600; 3818 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV; 3819 tty_set_operations(serial_driver, &ops); 3820 if ((rc = tty_register_driver(serial_driver)) < 0) { 3821 DBGERR(("%s can't register serial driver\n", driver_name)); 3822 put_tty_driver(serial_driver); 3823 serial_driver = NULL; 3824 goto error; 3825 } 3826 3827 printk(KERN_INFO "%s, tty major#%d\n", 3828 driver_name, serial_driver->major); 3829 3830 slgt_device_count = 0; 3831 if ((rc = pci_register_driver(&pci_driver)) < 0) { 3832 printk("%s pci_register_driver error=%d\n", driver_name, rc); 3833 goto error; 3834 } 3835 pci_registered = true; 3836 3837 if (!slgt_device_list) 3838 printk("%s no devices found\n",driver_name); 3839 3840 return 0; 3841 3842error: 3843 slgt_cleanup(); 3844 return rc; 3845} 3846 3847static void __exit slgt_exit(void) 3848{ 3849 slgt_cleanup(); 3850} 3851 3852module_init(slgt_init); 3853module_exit(slgt_exit); 3854 3855/* 3856 * register access routines 3857 */ 3858 3859#define CALC_REGADDR() \ 3860 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \ 3861 if (addr >= 0x80) \ 3862 reg_addr += (info->port_num) * 32; \ 3863 else if (addr >= 0x40) \ 3864 reg_addr += (info->port_num) * 16; 3865 3866static __u8 rd_reg8(struct slgt_info *info, unsigned int addr) 3867{ 3868 CALC_REGADDR(); 3869 return readb((void __iomem *)reg_addr); 3870} 3871 3872static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value) 3873{ 3874 CALC_REGADDR(); 3875 writeb(value, (void __iomem *)reg_addr); 3876} 3877 3878static __u16 rd_reg16(struct slgt_info *info, unsigned int addr) 3879{ 3880 CALC_REGADDR(); 3881 return readw((void __iomem *)reg_addr); 3882} 3883 3884static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value) 3885{ 3886 CALC_REGADDR(); 3887 writew(value, (void __iomem *)reg_addr); 3888} 3889 3890static __u32 rd_reg32(struct slgt_info *info, unsigned int addr) 3891{ 3892 CALC_REGADDR(); 3893 return readl((void __iomem *)reg_addr); 3894} 3895 3896static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value) 3897{ 3898 CALC_REGADDR(); 3899 writel(value, (void __iomem *)reg_addr); 3900} 3901 3902static void rdma_reset(struct slgt_info *info) 3903{ 3904 unsigned int i; 3905 3906 /* set reset bit */ 3907 wr_reg32(info, RDCSR, BIT1); 3908 3909 /* wait for enable bit cleared */ 3910 for(i=0 ; i < 1000 ; i++) 3911 if (!(rd_reg32(info, RDCSR) & BIT0)) 3912 break; 3913} 3914 3915static void tdma_reset(struct slgt_info *info) 3916{ 3917 unsigned int i; 3918 3919 /* set reset bit */ 3920 wr_reg32(info, TDCSR, BIT1); 3921 3922 /* wait for enable bit cleared */ 3923 for(i=0 ; i < 1000 ; i++) 3924 if (!(rd_reg32(info, TDCSR) & BIT0)) 3925 break; 3926} 3927 3928/* 3929 * enable internal loopback 3930 * TxCLK and RxCLK are generated from BRG 3931 * and TxD is looped back to RxD internally. 3932 */ 3933static void enable_loopback(struct slgt_info *info) 3934{ 3935 /* SCR (serial control) BIT2=loopback enable */ 3936 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2)); 3937 3938 if (info->params.mode != MGSL_MODE_ASYNC) { 3939 /* CCR (clock control) 3940 * 07..05 tx clock source (010 = BRG) 3941 * 04..02 rx clock source (010 = BRG) 3942 * 01 auxclk enable (0 = disable) 3943 * 00 BRG enable (1 = enable) 3944 * 3945 * 0100 1001 3946 */ 3947 wr_reg8(info, CCR, 0x49); 3948 3949 /* set speed if available, otherwise use default */ 3950 if (info->params.clock_speed) 3951 set_rate(info, info->params.clock_speed); 3952 else 3953 set_rate(info, 3686400); 3954 } 3955} 3956 3957/* 3958 * set baud rate generator to specified rate 3959 */ 3960static void set_rate(struct slgt_info *info, u32 rate) 3961{ 3962 unsigned int div; 3963 unsigned int osc = info->base_clock; 3964 3965 /* div = osc/rate - 1 3966 * 3967 * Round div up if osc/rate is not integer to 3968 * force to next slowest rate. 3969 */ 3970 3971 if (rate) { 3972 div = osc/rate; 3973 if (!(osc % rate) && div) 3974 div--; 3975 wr_reg16(info, BDR, (unsigned short)div); 3976 } 3977} 3978 3979static void rx_stop(struct slgt_info *info) 3980{ 3981 unsigned short val; 3982 3983 /* disable and reset receiver */ 3984 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */ 3985 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */ 3986 wr_reg16(info, RCR, val); /* clear reset bit */ 3987 3988 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE); 3989 3990 /* clear pending rx interrupts */ 3991 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER); 3992 3993 rdma_reset(info); 3994 3995 info->rx_enabled = false; 3996 info->rx_restart = false; 3997} 3998 3999static void rx_start(struct slgt_info *info) 4000{ 4001 unsigned short val; 4002 4003 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA); 4004 4005 /* clear pending rx overrun IRQ */ 4006 wr_reg16(info, SSR, IRQ_RXOVER); 4007 4008 /* reset and disable receiver */ 4009 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */ 4010 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */ 4011 wr_reg16(info, RCR, val); /* clear reset bit */ 4012 4013 rdma_reset(info); 4014 reset_rbufs(info); 4015 4016 if (info->rx_pio) { 4017 /* rx request when rx FIFO not empty */ 4018 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14)); 4019 slgt_irq_on(info, IRQ_RXDATA); 4020 if (info->params.mode == MGSL_MODE_ASYNC) { 4021 /* enable saving of rx status */ 4022 wr_reg32(info, RDCSR, BIT6); 4023 } 4024 } else { 4025 /* rx request when rx FIFO half full */ 4026 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14)); 4027 /* set 1st descriptor address */ 4028 wr_reg32(info, RDDAR, info->rbufs[0].pdesc); 4029 4030 if (info->params.mode != MGSL_MODE_ASYNC) { 4031 /* enable rx DMA and DMA interrupt */ 4032 wr_reg32(info, RDCSR, (BIT2 + BIT0)); 4033 } else { 4034 /* enable saving of rx status, rx DMA and DMA interrupt */ 4035 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0)); 4036 } 4037 } 4038 4039 slgt_irq_on(info, IRQ_RXOVER); 4040 4041 /* enable receiver */ 4042 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1)); 4043 4044 info->rx_restart = false; 4045 info->rx_enabled = true; 4046} 4047 4048static void tx_start(struct slgt_info *info) 4049{ 4050 if (!info->tx_enabled) { 4051 wr_reg16(info, TCR, 4052 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2)); 4053 info->tx_enabled = true; 4054 } 4055 4056 if (desc_count(info->tbufs[info->tbuf_start])) { 4057 info->drop_rts_on_tx_done = false; 4058 4059 if (info->params.mode != MGSL_MODE_ASYNC) { 4060 if (info->params.flags & HDLC_FLAG_AUTO_RTS) { 4061 get_signals(info); 4062 if (!(info->signals & SerialSignal_RTS)) { 4063 info->signals |= SerialSignal_RTS; 4064 set_signals(info); 4065 info->drop_rts_on_tx_done = true; 4066 } 4067 } 4068 4069 slgt_irq_off(info, IRQ_TXDATA); 4070 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE); 4071 /* clear tx idle and underrun status bits */ 4072 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER)); 4073 } else { 4074 slgt_irq_off(info, IRQ_TXDATA); 4075 slgt_irq_on(info, IRQ_TXIDLE); 4076 /* clear tx idle status bit */ 4077 wr_reg16(info, SSR, IRQ_TXIDLE); 4078 } 4079 /* set 1st descriptor address and start DMA */ 4080 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc); 4081 wr_reg32(info, TDCSR, BIT2 + BIT0); 4082 info->tx_active = true; 4083 } 4084} 4085 4086static void tx_stop(struct slgt_info *info) 4087{ 4088 unsigned short val; 4089 4090 del_timer(&info->tx_timer); 4091 4092 tdma_reset(info); 4093 4094 /* reset and disable transmitter */ 4095 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */ 4096 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */ 4097 4098 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER); 4099 4100 /* clear tx idle and underrun status bit */ 4101 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER)); 4102 4103 reset_tbufs(info); 4104 4105 info->tx_enabled = false; 4106 info->tx_active = false; 4107} 4108 4109static void reset_port(struct slgt_info *info) 4110{ 4111 if (!info->reg_addr) 4112 return; 4113 4114 tx_stop(info); 4115 rx_stop(info); 4116 4117 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR); 4118 set_signals(info); 4119 4120 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4121} 4122 4123static void reset_adapter(struct slgt_info *info) 4124{ 4125 int i; 4126 for (i=0; i < info->port_count; ++i) { 4127 if (info->port_array[i]) 4128 reset_port(info->port_array[i]); 4129 } 4130} 4131 4132static void async_mode(struct slgt_info *info) 4133{ 4134 unsigned short val; 4135 4136 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4137 tx_stop(info); 4138 rx_stop(info); 4139 4140 /* TCR (tx control) 4141 * 4142 * 15..13 mode, 010=async 4143 * 12..10 encoding, 000=NRZ 4144 * 09 parity enable 4145 * 08 1=odd parity, 0=even parity 4146 * 07 1=RTS driver control 4147 * 06 1=break enable 4148 * 05..04 character length 4149 * 00=5 bits 4150 * 01=6 bits 4151 * 10=7 bits 4152 * 11=8 bits 4153 * 03 0=1 stop bit, 1=2 stop bits 4154 * 02 reset 4155 * 01 enable 4156 * 00 auto-CTS enable 4157 */ 4158 val = 0x4000; 4159 4160 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 4161 val |= BIT7; 4162 4163 if (info->params.parity != ASYNC_PARITY_NONE) { 4164 val |= BIT9; 4165 if (info->params.parity == ASYNC_PARITY_ODD) 4166 val |= BIT8; 4167 } 4168 4169 switch (info->params.data_bits) 4170 { 4171 case 6: val |= BIT4; break; 4172 case 7: val |= BIT5; break; 4173 case 8: val |= BIT5 + BIT4; break; 4174 } 4175 4176 if (info->params.stop_bits != 1) 4177 val |= BIT3; 4178 4179 if (info->params.flags & HDLC_FLAG_AUTO_CTS) 4180 val |= BIT0; 4181 4182 wr_reg16(info, TCR, val); 4183 4184 /* RCR (rx control) 4185 * 4186 * 15..13 mode, 010=async 4187 * 12..10 encoding, 000=NRZ 4188 * 09 parity enable 4189 * 08 1=odd parity, 0=even parity 4190 * 07..06 reserved, must be 0 4191 * 05..04 character length 4192 * 00=5 bits 4193 * 01=6 bits 4194 * 10=7 bits 4195 * 11=8 bits 4196 * 03 reserved, must be zero 4197 * 02 reset 4198 * 01 enable 4199 * 00 auto-DCD enable 4200 */ 4201 val = 0x4000; 4202 4203 if (info->params.parity != ASYNC_PARITY_NONE) { 4204 val |= BIT9; 4205 if (info->params.parity == ASYNC_PARITY_ODD) 4206 val |= BIT8; 4207 } 4208 4209 switch (info->params.data_bits) 4210 { 4211 case 6: val |= BIT4; break; 4212 case 7: val |= BIT5; break; 4213 case 8: val |= BIT5 + BIT4; break; 4214 } 4215 4216 if (info->params.flags & HDLC_FLAG_AUTO_DCD) 4217 val |= BIT0; 4218 4219 wr_reg16(info, RCR, val); 4220 4221 /* CCR (clock control) 4222 * 4223 * 07..05 011 = tx clock source is BRG/16 4224 * 04..02 010 = rx clock source is BRG 4225 * 01 0 = auxclk disabled 4226 * 00 1 = BRG enabled 4227 * 4228 * 0110 1001 4229 */ 4230 wr_reg8(info, CCR, 0x69); 4231 4232 msc_set_vcr(info); 4233 4234 /* SCR (serial control) 4235 * 4236 * 15 1=tx req on FIFO half empty 4237 * 14 1=rx req on FIFO half full 4238 * 13 tx data IRQ enable 4239 * 12 tx idle IRQ enable 4240 * 11 rx break on IRQ enable 4241 * 10 rx data IRQ enable 4242 * 09 rx break off IRQ enable 4243 * 08 overrun IRQ enable 4244 * 07 DSR IRQ enable 4245 * 06 CTS IRQ enable 4246 * 05 DCD IRQ enable 4247 * 04 RI IRQ enable 4248 * 03 0=16x sampling, 1=8x sampling 4249 * 02 1=txd->rxd internal loopback enable 4250 * 01 reserved, must be zero 4251 * 00 1=master IRQ enable 4252 */ 4253 val = BIT15 + BIT14 + BIT0; 4254 /* JCR[8] : 1 = x8 async mode feature available */ 4255 if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate && 4256 ((info->base_clock < (info->params.data_rate * 16)) || 4257 (info->base_clock % (info->params.data_rate * 16)))) { 4258 /* use 8x sampling */ 4259 val |= BIT3; 4260 set_rate(info, info->params.data_rate * 8); 4261 } else { 4262 /* use 16x sampling */ 4263 set_rate(info, info->params.data_rate * 16); 4264 } 4265 wr_reg16(info, SCR, val); 4266 4267 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER); 4268 4269 if (info->params.loopback) 4270 enable_loopback(info); 4271} 4272 4273static void sync_mode(struct slgt_info *info) 4274{ 4275 unsigned short val; 4276 4277 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER); 4278 tx_stop(info); 4279 rx_stop(info); 4280 4281 /* TCR (tx control) 4282 * 4283 * 15..13 mode 4284 * 000=HDLC/SDLC 4285 * 001=raw bit synchronous 4286 * 010=asynchronous/isochronous 4287 * 011=monosync byte synchronous 4288 * 100=bisync byte synchronous 4289 * 101=xsync byte synchronous 4290 * 12..10 encoding 4291 * 09 CRC enable 4292 * 08 CRC32 4293 * 07 1=RTS driver control 4294 * 06 preamble enable 4295 * 05..04 preamble length 4296 * 03 share open/close flag 4297 * 02 reset 4298 * 01 enable 4299 * 00 auto-CTS enable 4300 */ 4301 val = BIT2; 4302 4303 switch(info->params.mode) { 4304 case MGSL_MODE_XSYNC: 4305 val |= BIT15 + BIT13; 4306 break; 4307 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break; 4308 case MGSL_MODE_BISYNC: val |= BIT15; break; 4309 case MGSL_MODE_RAW: val |= BIT13; break; 4310 } 4311 if (info->if_mode & MGSL_INTERFACE_RTS_EN) 4312 val |= BIT7; 4313 4314 switch(info->params.encoding) 4315 { 4316 case HDLC_ENCODING_NRZB: val |= BIT10; break; 4317 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break; 4318 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break; 4319 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break; 4320 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break; 4321 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break; 4322 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break; 4323 } 4324 4325 switch (info->params.crc_type & HDLC_CRC_MASK) 4326 { 4327 case HDLC_CRC_16_CCITT: val |= BIT9; break; 4328 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break; 4329 } 4330 4331 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE) 4332 val |= BIT6; 4333 4334 switch (info->params.preamble_length) 4335 { 4336 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break; 4337 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break; 4338 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break; 4339 } 4340 4341 if (info->params.flags & HDLC_FLAG_AUTO_CTS) 4342 val |= BIT0; 4343 4344 wr_reg16(info, TCR, val); 4345 4346 /* TPR (transmit preamble) */ 4347 4348 switch (info->params.preamble) 4349 { 4350 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break; 4351 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break; 4352 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break; 4353 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break; 4354 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break; 4355 default: val = 0x7e; break; 4356 } 4357 wr_reg8(info, TPR, (unsigned char)val); 4358 4359 /* RCR (rx control) 4360 * 4361 * 15..13 mode 4362 * 000=HDLC/SDLC 4363 * 001=raw bit synchronous 4364 * 010=asynchronous/isochronous 4365 * 011=monosync byte synchronous 4366 * 100=bisync byte synchronous 4367 * 101=xsync byte synchronous 4368 * 12..10 encoding 4369 * 09 CRC enable 4370 * 08 CRC32 4371 * 07..03 reserved, must be 0 4372 * 02 reset 4373 * 01 enable 4374 * 00 auto-DCD enable 4375 */ 4376 val = 0; 4377 4378 switch(info->params.mode) { 4379 case MGSL_MODE_XSYNC: 4380 val |= BIT15 + BIT13; 4381 break; 4382 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break; 4383 case MGSL_MODE_BISYNC: val |= BIT15; break; 4384 case MGSL_MODE_RAW: val |= BIT13; break; 4385 } 4386 4387 switch(info->params.encoding) 4388 { 4389 case HDLC_ENCODING_NRZB: val |= BIT10; break; 4390 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break; 4391 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break; 4392 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break; 4393 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break; 4394 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break; 4395 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break; 4396 } 4397 4398 switch (info->params.crc_type & HDLC_CRC_MASK) 4399 { 4400 case HDLC_CRC_16_CCITT: val |= BIT9; break; 4401 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break; 4402 } 4403 4404 if (info->params.flags & HDLC_FLAG_AUTO_DCD) 4405 val |= BIT0; 4406 4407 wr_reg16(info, RCR, val); 4408 4409 /* CCR (clock control) 4410 * 4411 * 07..05 tx clock source 4412 * 04..02 rx clock source 4413 * 01 auxclk enable 4414 * 00 BRG enable 4415 */ 4416 val = 0; 4417 4418 if (info->params.flags & HDLC_FLAG_TXC_BRG) 4419 { 4420 // when RxC source is DPLL, BRG generates 16X DPLL 4421 // reference clock, so take TxC from BRG/16 to get 4422 // transmit clock at actual data rate 4423 if (info->params.flags & HDLC_FLAG_RXC_DPLL) 4424 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */ 4425 else 4426 val |= BIT6; /* 010, txclk = BRG */ 4427 } 4428 else if (info->params.flags & HDLC_FLAG_TXC_DPLL) 4429 val |= BIT7; /* 100, txclk = DPLL Input */ 4430 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN) 4431 val |= BIT5; /* 001, txclk = RXC Input */ 4432 4433 if (info->params.flags & HDLC_FLAG_RXC_BRG) 4434 val |= BIT3; /* 010, rxclk = BRG */ 4435 else if (info->params.flags & HDLC_FLAG_RXC_DPLL) 4436 val |= BIT4; /* 100, rxclk = DPLL */ 4437 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN) 4438 val |= BIT2; /* 001, rxclk = TXC Input */ 4439 4440 if (info->params.clock_speed) 4441 val |= BIT1 + BIT0; 4442 4443 wr_reg8(info, CCR, (unsigned char)val); 4444 4445 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL)) 4446 { 4447 // program DPLL mode 4448 switch(info->params.encoding) 4449 { 4450 case HDLC_ENCODING_BIPHASE_MARK: 4451 case HDLC_ENCODING_BIPHASE_SPACE: 4452 val = BIT7; break; 4453 case HDLC_ENCODING_BIPHASE_LEVEL: 4454 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: 4455 val = BIT7 + BIT6; break; 4456 default: val = BIT6; // NRZ encodings 4457 } 4458 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val)); 4459 4460 // DPLL requires a 16X reference clock from BRG 4461 set_rate(info, info->params.clock_speed * 16); 4462 } 4463 else 4464 set_rate(info, info->params.clock_speed); 4465 4466 tx_set_idle(info); 4467 4468 msc_set_vcr(info); 4469 4470 /* SCR (serial control) 4471 * 4472 * 15 1=tx req on FIFO half empty 4473 * 14 1=rx req on FIFO half full 4474 * 13 tx data IRQ enable 4475 * 12 tx idle IRQ enable 4476 * 11 underrun IRQ enable 4477 * 10 rx data IRQ enable 4478 * 09 rx idle IRQ enable 4479 * 08 overrun IRQ enable 4480 * 07 DSR IRQ enable 4481 * 06 CTS IRQ enable 4482 * 05 DCD IRQ enable 4483 * 04 RI IRQ enable 4484 * 03 reserved, must be zero 4485 * 02 1=txd->rxd internal loopback enable 4486 * 01 reserved, must be zero 4487 * 00 1=master IRQ enable 4488 */ 4489 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0); 4490 4491 if (info->params.loopback) 4492 enable_loopback(info); 4493} 4494 4495/* 4496 * set transmit idle mode 4497 */ 4498static void tx_set_idle(struct slgt_info *info) 4499{ 4500 unsigned char val; 4501 unsigned short tcr; 4502 4503 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits 4504 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits 4505 */ 4506 tcr = rd_reg16(info, TCR); 4507 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) { 4508 /* disable preamble, set idle size to 16 bits */ 4509 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4; 4510 /* MSB of 16 bit idle specified in tx preamble register (TPR) */ 4511 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff)); 4512 } else if (!(tcr & BIT6)) { 4513 /* preamble is disabled, set idle size to 8 bits */ 4514 tcr &= ~(BIT5 + BIT4); 4515 } 4516 wr_reg16(info, TCR, tcr); 4517 4518 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) { 4519 /* LSB of custom tx idle specified in tx idle register */ 4520 val = (unsigned char)(info->idle_mode & 0xff); 4521 } else { 4522 /* standard 8 bit idle patterns */ 4523 switch(info->idle_mode) 4524 { 4525 case HDLC_TXIDLE_FLAGS: val = 0x7e; break; 4526 case HDLC_TXIDLE_ALT_ZEROS_ONES: 4527 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break; 4528 case HDLC_TXIDLE_ZEROS: 4529 case HDLC_TXIDLE_SPACE: val = 0x00; break; 4530 default: val = 0xff; 4531 } 4532 } 4533 4534 wr_reg8(info, TIR, val); 4535} 4536 4537/* 4538 * get state of V24 status (input) signals 4539 */ 4540static void get_signals(struct slgt_info *info) 4541{ 4542 unsigned short status = rd_reg16(info, SSR); 4543 4544 /* clear all serial signals except RTS and DTR */ 4545 info->signals &= SerialSignal_RTS | SerialSignal_DTR; 4546 4547 if (status & BIT3) 4548 info->signals |= SerialSignal_DSR; 4549 if (status & BIT2) 4550 info->signals |= SerialSignal_CTS; 4551 if (status & BIT1) 4552 info->signals |= SerialSignal_DCD; 4553 if (status & BIT0) 4554 info->signals |= SerialSignal_RI; 4555} 4556 4557/* 4558 * set V.24 Control Register based on current configuration 4559 */ 4560static void msc_set_vcr(struct slgt_info *info) 4561{ 4562 unsigned char val = 0; 4563 4564 /* VCR (V.24 control) 4565 * 4566 * 07..04 serial IF select 4567 * 03 DTR 4568 * 02 RTS 4569 * 01 LL 4570 * 00 RL 4571 */ 4572 4573 switch(info->if_mode & MGSL_INTERFACE_MASK) 4574 { 4575 case MGSL_INTERFACE_RS232: 4576 val |= BIT5; /* 0010 */ 4577 break; 4578 case MGSL_INTERFACE_V35: 4579 val |= BIT7 + BIT6 + BIT5; /* 1110 */ 4580 break; 4581 case MGSL_INTERFACE_RS422: 4582 val |= BIT6; /* 0100 */ 4583 break; 4584 } 4585 4586 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST) 4587 val |= BIT4; 4588 if (info->signals & SerialSignal_DTR) 4589 val |= BIT3; 4590 if (info->signals & SerialSignal_RTS) 4591 val |= BIT2; 4592 if (info->if_mode & MGSL_INTERFACE_LL) 4593 val |= BIT1; 4594 if (info->if_mode & MGSL_INTERFACE_RL) 4595 val |= BIT0; 4596 wr_reg8(info, VCR, val); 4597} 4598 4599/* 4600 * set state of V24 control (output) signals 4601 */ 4602static void set_signals(struct slgt_info *info) 4603{ 4604 unsigned char val = rd_reg8(info, VCR); 4605 if (info->signals & SerialSignal_DTR) 4606 val |= BIT3; 4607 else 4608 val &= ~BIT3; 4609 if (info->signals & SerialSignal_RTS) 4610 val |= BIT2; 4611 else 4612 val &= ~BIT2; 4613 wr_reg8(info, VCR, val); 4614} 4615 4616/* 4617 * free range of receive DMA buffers (i to last) 4618 */ 4619static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last) 4620{ 4621 int done = 0; 4622 4623 while(!done) { 4624 /* reset current buffer for reuse */ 4625 info->rbufs[i].status = 0; 4626 set_desc_count(info->rbufs[i], info->rbuf_fill_level); 4627 if (i == last) 4628 done = 1; 4629 if (++i == info->rbuf_count) 4630 i = 0; 4631 } 4632 info->rbuf_current = i; 4633} 4634 4635/* 4636 * mark all receive DMA buffers as free 4637 */ 4638static void reset_rbufs(struct slgt_info *info) 4639{ 4640 free_rbufs(info, 0, info->rbuf_count - 1); 4641 info->rbuf_fill_index = 0; 4642 info->rbuf_fill_count = 0; 4643} 4644 4645/* 4646 * pass receive HDLC frame to upper layer 4647 * 4648 * return true if frame available, otherwise false 4649 */ 4650static bool rx_get_frame(struct slgt_info *info) 4651{ 4652 unsigned int start, end; 4653 unsigned short status; 4654 unsigned int framesize = 0; 4655 unsigned long flags; 4656 struct tty_struct *tty = info->port.tty; 4657 unsigned char addr_field = 0xff; 4658 unsigned int crc_size = 0; 4659 4660 switch (info->params.crc_type & HDLC_CRC_MASK) { 4661 case HDLC_CRC_16_CCITT: crc_size = 2; break; 4662 case HDLC_CRC_32_CCITT: crc_size = 4; break; 4663 } 4664 4665check_again: 4666 4667 framesize = 0; 4668 addr_field = 0xff; 4669 start = end = info->rbuf_current; 4670 4671 for (;;) { 4672 if (!desc_complete(info->rbufs[end])) 4673 goto cleanup; 4674 4675 if (framesize == 0 && info->params.addr_filter != 0xff) 4676 addr_field = info->rbufs[end].buf[0]; 4677 4678 framesize += desc_count(info->rbufs[end]); 4679 4680 if (desc_eof(info->rbufs[end])) 4681 break; 4682 4683 if (++end == info->rbuf_count) 4684 end = 0; 4685 4686 if (end == info->rbuf_current) { 4687 if (info->rx_enabled){ 4688 spin_lock_irqsave(&info->lock,flags); 4689 rx_start(info); 4690 spin_unlock_irqrestore(&info->lock,flags); 4691 } 4692 goto cleanup; 4693 } 4694 } 4695 4696 /* status 4697 * 4698 * 15 buffer complete 4699 * 14..06 reserved 4700 * 05..04 residue 4701 * 02 eof (end of frame) 4702 * 01 CRC error 4703 * 00 abort 4704 */ 4705 status = desc_status(info->rbufs[end]); 4706 4707 /* ignore CRC bit if not using CRC (bit is undefined) */ 4708 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE) 4709 status &= ~BIT1; 4710 4711 if (framesize == 0 || 4712 (addr_field != 0xff && addr_field != info->params.addr_filter)) { 4713 free_rbufs(info, start, end); 4714 goto check_again; 4715 } 4716 4717 if (framesize < (2 + crc_size) || status & BIT0) { 4718 info->icount.rxshort++; 4719 framesize = 0; 4720 } else if (status & BIT1) { 4721 info->icount.rxcrc++; 4722 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) 4723 framesize = 0; 4724 } 4725 4726#if SYNCLINK_GENERIC_HDLC 4727 if (framesize == 0) { 4728 info->netdev->stats.rx_errors++; 4729 info->netdev->stats.rx_frame_errors++; 4730 } 4731#endif 4732 4733 DBGBH(("%s rx frame status=%04X size=%d\n", 4734 info->device_name, status, framesize)); 4735 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx"); 4736 4737 if (framesize) { 4738 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) { 4739 framesize -= crc_size; 4740 crc_size = 0; 4741 } 4742 4743 if (framesize > info->max_frame_size + crc_size) 4744 info->icount.rxlong++; 4745 else { 4746 /* copy dma buffer(s) to contiguous temp buffer */ 4747 int copy_count = framesize; 4748 int i = start; 4749 unsigned char *p = info->tmp_rbuf; 4750 info->tmp_rbuf_count = framesize; 4751 4752 info->icount.rxok++; 4753 4754 while(copy_count) { 4755 int partial_count = min_t(int, copy_count, info->rbuf_fill_level); 4756 memcpy(p, info->rbufs[i].buf, partial_count); 4757 p += partial_count; 4758 copy_count -= partial_count; 4759 if (++i == info->rbuf_count) 4760 i = 0; 4761 } 4762 4763 if (info->params.crc_type & HDLC_CRC_RETURN_EX) { 4764 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK; 4765 framesize++; 4766 } 4767 4768#if SYNCLINK_GENERIC_HDLC 4769 if (info->netcount) 4770 hdlcdev_rx(info,info->tmp_rbuf, framesize); 4771 else 4772#endif 4773 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize); 4774 } 4775 } 4776 free_rbufs(info, start, end); 4777 return true; 4778 4779cleanup: 4780 return false; 4781} 4782 4783/* 4784 * pass receive buffer (RAW synchronous mode) to tty layer 4785 * return true if buffer available, otherwise false 4786 */ 4787static bool rx_get_buf(struct slgt_info *info) 4788{ 4789 unsigned int i = info->rbuf_current; 4790 unsigned int count; 4791 4792 if (!desc_complete(info->rbufs[i])) 4793 return false; 4794 count = desc_count(info->rbufs[i]); 4795 switch(info->params.mode) { 4796 case MGSL_MODE_MONOSYNC: 4797 case MGSL_MODE_BISYNC: 4798 case MGSL_MODE_XSYNC: 4799 /* ignore residue in byte synchronous modes */ 4800 if (desc_residue(info->rbufs[i])) 4801 count--; 4802 break; 4803 } 4804 DBGDATA(info, info->rbufs[i].buf, count, "rx"); 4805 DBGINFO(("rx_get_buf size=%d\n", count)); 4806 if (count) 4807 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf, 4808 info->flag_buf, count); 4809 free_rbufs(info, i, i); 4810 return true; 4811} 4812 4813static void reset_tbufs(struct slgt_info *info) 4814{ 4815 unsigned int i; 4816 info->tbuf_current = 0; 4817 for (i=0 ; i < info->tbuf_count ; i++) { 4818 info->tbufs[i].status = 0; 4819 info->tbufs[i].count = 0; 4820 } 4821} 4822 4823/* 4824 * return number of free transmit DMA buffers 4825 */ 4826static unsigned int free_tbuf_count(struct slgt_info *info) 4827{ 4828 unsigned int count = 0; 4829 unsigned int i = info->tbuf_current; 4830 4831 do 4832 { 4833 if (desc_count(info->tbufs[i])) 4834 break; /* buffer in use */ 4835 ++count; 4836 if (++i == info->tbuf_count) 4837 i=0; 4838 } while (i != info->tbuf_current); 4839 4840 /* if tx DMA active, last zero count buffer is in use */ 4841 if (count && (rd_reg32(info, TDCSR) & BIT0)) 4842 --count; 4843 4844 return count; 4845} 4846 4847/* 4848 * return number of bytes in unsent transmit DMA buffers 4849 * and the serial controller tx FIFO 4850 */ 4851static unsigned int tbuf_bytes(struct slgt_info *info) 4852{ 4853 unsigned int total_count = 0; 4854 unsigned int i = info->tbuf_current; 4855 unsigned int reg_value; 4856 unsigned int count; 4857 unsigned int active_buf_count = 0; 4858 4859 /* 4860 * Add descriptor counts for all tx DMA buffers. 4861 * If count is zero (cleared by DMA controller after read), 4862 * the buffer is complete or is actively being read from. 4863 * 4864 * Record buf_count of last buffer with zero count starting 4865 * from current ring position. buf_count is mirror 4866 * copy of count and is not cleared by serial controller. 4867 * If DMA controller is active, that buffer is actively 4868 * being read so add to total. 4869 */ 4870 do { 4871 count = desc_count(info->tbufs[i]); 4872 if (count) 4873 total_count += count; 4874 else if (!total_count) 4875 active_buf_count = info->tbufs[i].buf_count; 4876 if (++i == info->tbuf_count) 4877 i = 0; 4878 } while (i != info->tbuf_current); 4879 4880 /* read tx DMA status register */ 4881 reg_value = rd_reg32(info, TDCSR); 4882 4883 /* if tx DMA active, last zero count buffer is in use */ 4884 if (reg_value & BIT0) 4885 total_count += active_buf_count; 4886 4887 /* add tx FIFO count = reg_value[15..8] */ 4888 total_count += (reg_value >> 8) & 0xff; 4889 4890 /* if transmitter active add one byte for shift register */ 4891 if (info->tx_active) 4892 total_count++; 4893 4894 return total_count; 4895} 4896 4897/* 4898 * load data into transmit DMA buffer ring and start transmitter if needed 4899 * return true if data accepted, otherwise false (buffers full) 4900 */ 4901static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size) 4902{ 4903 unsigned short count; 4904 unsigned int i; 4905 struct slgt_desc *d; 4906 4907 /* check required buffer space */ 4908 if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info)) 4909 return false; 4910 4911 DBGDATA(info, buf, size, "tx"); 4912 4913 /* 4914 * copy data to one or more DMA buffers in circular ring 4915 * tbuf_start = first buffer for this data 4916 * tbuf_current = next free buffer 4917 * 4918 * Copy all data before making data visible to DMA controller by 4919 * setting descriptor count of the first buffer. 4920 * This prevents an active DMA controller from reading the first DMA 4921 * buffers of a frame and stopping before the final buffers are filled. 4922 */ 4923 4924 info->tbuf_start = i = info->tbuf_current; 4925 4926 while (size) { 4927 d = &info->tbufs[i]; 4928 4929 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size); 4930 memcpy(d->buf, buf, count); 4931 4932 size -= count; 4933 buf += count; 4934 4935 /* 4936 * set EOF bit for last buffer of HDLC frame or 4937 * for every buffer in raw mode 4938 */ 4939 if ((!size && info->params.mode == MGSL_MODE_HDLC) || 4940 info->params.mode == MGSL_MODE_RAW) 4941 set_desc_eof(*d, 1); 4942 else 4943 set_desc_eof(*d, 0); 4944 4945 /* set descriptor count for all but first buffer */ 4946 if (i != info->tbuf_start) 4947 set_desc_count(*d, count); 4948 d->buf_count = count; 4949 4950 if (++i == info->tbuf_count) 4951 i = 0; 4952 } 4953 4954 info->tbuf_current = i; 4955 4956 /* set first buffer count to make new data visible to DMA controller */ 4957 d = &info->tbufs[info->tbuf_start]; 4958 set_desc_count(*d, d->buf_count); 4959 4960 /* start transmitter if needed and update transmit timeout */ 4961 if (!info->tx_active) 4962 tx_start(info); 4963 update_tx_timer(info); 4964 4965 return true; 4966} 4967 4968static int register_test(struct slgt_info *info) 4969{ 4970 static unsigned short patterns[] = 4971 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696}; 4972 static unsigned int count = ARRAY_SIZE(patterns); 4973 unsigned int i; 4974 int rc = 0; 4975 4976 for (i=0 ; i < count ; i++) { 4977 wr_reg16(info, TIR, patterns[i]); 4978 wr_reg16(info, BDR, patterns[(i+1)%count]); 4979 if ((rd_reg16(info, TIR) != patterns[i]) || 4980 (rd_reg16(info, BDR) != patterns[(i+1)%count])) { 4981 rc = -ENODEV; 4982 break; 4983 } 4984 } 4985 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0; 4986 info->init_error = rc ? 0 : DiagStatus_AddressFailure; 4987 return rc; 4988} 4989 4990static int irq_test(struct slgt_info *info) 4991{ 4992 unsigned long timeout; 4993 unsigned long flags; 4994 struct tty_struct *oldtty = info->port.tty; 4995 u32 speed = info->params.data_rate; 4996 4997 info->params.data_rate = 921600; 4998 info->port.tty = NULL; 4999 5000 spin_lock_irqsave(&info->lock, flags); 5001 async_mode(info); 5002 slgt_irq_on(info, IRQ_TXIDLE); 5003 5004 /* enable transmitter */ 5005 wr_reg16(info, TCR, 5006 (unsigned short)(rd_reg16(info, TCR) | BIT1)); 5007 5008 /* write one byte and wait for tx idle */ 5009 wr_reg16(info, TDR, 0); 5010 5011 /* assume failure */ 5012 info->init_error = DiagStatus_IrqFailure; 5013 info->irq_occurred = false; 5014 5015 spin_unlock_irqrestore(&info->lock, flags); 5016 5017 timeout=100; 5018 while(timeout-- && !info->irq_occurred) 5019 msleep_interruptible(10); 5020 5021 spin_lock_irqsave(&info->lock,flags); 5022 reset_port(info); 5023 spin_unlock_irqrestore(&info->lock,flags); 5024 5025 info->params.data_rate = speed; 5026 info->port.tty = oldtty; 5027 5028 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure; 5029 return info->irq_occurred ? 0 : -ENODEV; 5030} 5031 5032static int loopback_test_rx(struct slgt_info *info) 5033{ 5034 unsigned char *src, *dest; 5035 int count; 5036 5037 if (desc_complete(info->rbufs[0])) { 5038 count = desc_count(info->rbufs[0]); 5039 src = info->rbufs[0].buf; 5040 dest = info->tmp_rbuf; 5041 5042 for( ; count ; count-=2, src+=2) { 5043 /* src=data byte (src+1)=status byte */ 5044 if (!(*(src+1) & (BIT9 + BIT8))) { 5045 *dest = *src; 5046 dest++; 5047 info->tmp_rbuf_count++; 5048 } 5049 } 5050 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx"); 5051 return 1; 5052 } 5053 return 0; 5054} 5055 5056static int loopback_test(struct slgt_info *info) 5057{ 5058#define TESTFRAMESIZE 20 5059 5060 unsigned long timeout; 5061 u16 count = TESTFRAMESIZE; 5062 unsigned char buf[TESTFRAMESIZE]; 5063 int rc = -ENODEV; 5064 unsigned long flags; 5065 5066 struct tty_struct *oldtty = info->port.tty; 5067 MGSL_PARAMS params; 5068 5069 memcpy(¶ms, &info->params, sizeof(params)); 5070 5071 info->params.mode = MGSL_MODE_ASYNC; 5072 info->params.data_rate = 921600; 5073 info->params.loopback = 1; 5074 info->port.tty = NULL; 5075 5076 /* build and send transmit frame */ 5077 for (count = 0; count < TESTFRAMESIZE; ++count) 5078 buf[count] = (unsigned char)count; 5079 5080 info->tmp_rbuf_count = 0; 5081 memset(info->tmp_rbuf, 0, TESTFRAMESIZE); 5082 5083 /* program hardware for HDLC and enabled receiver */ 5084 spin_lock_irqsave(&info->lock,flags); 5085 async_mode(info); 5086 rx_start(info); 5087 tx_load(info, buf, count); 5088 spin_unlock_irqrestore(&info->lock, flags); 5089 5090 /* wait for receive complete */ 5091 for (timeout = 100; timeout; --timeout) { 5092 msleep_interruptible(10); 5093 if (loopback_test_rx(info)) { 5094 rc = 0; 5095 break; 5096 } 5097 } 5098 5099 /* verify received frame length and contents */ 5100 if (!rc && (info->tmp_rbuf_count != count || 5101 memcmp(buf, info->tmp_rbuf, count))) { 5102 rc = -ENODEV; 5103 } 5104 5105 spin_lock_irqsave(&info->lock,flags); 5106 reset_adapter(info); 5107 spin_unlock_irqrestore(&info->lock,flags); 5108 5109 memcpy(&info->params, ¶ms, sizeof(info->params)); 5110 info->port.tty = oldtty; 5111 5112 info->init_error = rc ? DiagStatus_DmaFailure : 0; 5113 return rc; 5114} 5115 5116static int adapter_test(struct slgt_info *info) 5117{ 5118 DBGINFO(("testing %s\n", info->device_name)); 5119 if (register_test(info) < 0) { 5120 printk("register test failure %s addr=%08X\n", 5121 info->device_name, info->phys_reg_addr); 5122 } else if (irq_test(info) < 0) { 5123 printk("IRQ test failure %s IRQ=%d\n", 5124 info->device_name, info->irq_level); 5125 } else if (loopback_test(info) < 0) { 5126 printk("loopback test failure %s\n", info->device_name); 5127 } 5128 return info->init_error; 5129} 5130 5131/* 5132 * transmit timeout handler 5133 */ 5134static void tx_timeout(unsigned long context) 5135{ 5136 struct slgt_info *info = (struct slgt_info*)context; 5137 unsigned long flags; 5138 5139 DBGINFO(("%s tx_timeout\n", info->device_name)); 5140 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) { 5141 info->icount.txtimeout++; 5142 } 5143 spin_lock_irqsave(&info->lock,flags); 5144 tx_stop(info); 5145 spin_unlock_irqrestore(&info->lock,flags); 5146 5147#if SYNCLINK_GENERIC_HDLC 5148 if (info->netcount) 5149 hdlcdev_tx_done(info); 5150 else 5151#endif 5152 bh_transmit(info); 5153} 5154 5155/* 5156 * receive buffer polling timer 5157 */ 5158static void rx_timeout(unsigned long context) 5159{ 5160 struct slgt_info *info = (struct slgt_info*)context; 5161 unsigned long flags; 5162 5163 DBGINFO(("%s rx_timeout\n", info->device_name)); 5164 spin_lock_irqsave(&info->lock, flags); 5165 info->pending_bh |= BH_RECEIVE; 5166 spin_unlock_irqrestore(&info->lock, flags); 5167 bh_handler(&info->task); 5168} 5169 5170