1/* sunzilog.c: Zilog serial driver for Sparc systems. 2 * 3 * Driver for Zilog serial chips found on Sun workstations and 4 * servers. This driver could actually be made more generic. 5 * 6 * This is based on the old drivers/sbus/char/zs.c code. A lot 7 * of code has been simply moved over directly from there but 8 * much has been rewritten. Credits therefore go out to Eddie 9 * C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell for their 10 * work there. 11 * 12 * Copyright (C) 2002, 2006, 2007 David S. Miller (davem@davemloft.net) 13 */ 14 15#include <linux/module.h> 16#include <linux/kernel.h> 17#include <linux/errno.h> 18#include <linux/delay.h> 19#include <linux/tty.h> 20#include <linux/tty_flip.h> 21#include <linux/major.h> 22#include <linux/string.h> 23#include <linux/ptrace.h> 24#include <linux/ioport.h> 25#include <linux/slab.h> 26#include <linux/circ_buf.h> 27#include <linux/serial.h> 28#include <linux/sysrq.h> 29#include <linux/console.h> 30#include <linux/spinlock.h> 31#ifdef CONFIG_SERIO 32#include <linux/serio.h> 33#endif 34#include <linux/init.h> 35#include <linux/of_device.h> 36 37#include <asm/io.h> 38#include <asm/irq.h> 39#include <asm/prom.h> 40#include <asm/setup.h> 41 42#if defined(CONFIG_SERIAL_SUNZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 43#define SUPPORT_SYSRQ 44#endif 45 46#include <linux/serial_core.h> 47#include <linux/sunserialcore.h> 48 49#include "sunzilog.h" 50 51/* On 32-bit sparcs we need to delay after register accesses 52 * to accommodate sun4 systems, but we do not need to flush writes. 53 * On 64-bit sparc we only need to flush single writes to ensure 54 * completion. 55 */ 56#ifndef CONFIG_SPARC64 57#define ZSDELAY() udelay(5) 58#define ZSDELAY_LONG() udelay(20) 59#define ZS_WSYNC(channel) do { } while (0) 60#else 61#define ZSDELAY() 62#define ZSDELAY_LONG() 63#define ZS_WSYNC(__channel) \ 64 readb(&((__channel)->control)) 65#endif 66 67#define ZS_CLOCK 4915200 /* Zilog input clock rate. */ 68#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */ 69 70/* 71 * We wrap our port structure around the generic uart_port. 72 */ 73struct uart_sunzilog_port { 74 struct uart_port port; 75 76 /* IRQ servicing chain. */ 77 struct uart_sunzilog_port *next; 78 79 /* Current values of Zilog write registers. */ 80 unsigned char curregs[NUM_ZSREGS]; 81 82 unsigned int flags; 83#define SUNZILOG_FLAG_CONS_KEYB 0x00000001 84#define SUNZILOG_FLAG_CONS_MOUSE 0x00000002 85#define SUNZILOG_FLAG_IS_CONS 0x00000004 86#define SUNZILOG_FLAG_IS_KGDB 0x00000008 87#define SUNZILOG_FLAG_MODEM_STATUS 0x00000010 88#define SUNZILOG_FLAG_IS_CHANNEL_A 0x00000020 89#define SUNZILOG_FLAG_REGS_HELD 0x00000040 90#define SUNZILOG_FLAG_TX_STOPPED 0x00000080 91#define SUNZILOG_FLAG_TX_ACTIVE 0x00000100 92#define SUNZILOG_FLAG_ESCC 0x00000200 93#define SUNZILOG_FLAG_ISR_HANDLER 0x00000400 94 95 unsigned int cflag; 96 97 unsigned char parity_mask; 98 unsigned char prev_status; 99 100#ifdef CONFIG_SERIO 101 struct serio serio; 102 int serio_open; 103#endif 104}; 105 106static void sunzilog_putchar(struct uart_port *port, int ch); 107 108#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel __iomem *)((PORT)->membase)) 109#define UART_ZILOG(PORT) ((struct uart_sunzilog_port *)(PORT)) 110 111#define ZS_IS_KEYB(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_KEYB) 112#define ZS_IS_MOUSE(UP) ((UP)->flags & SUNZILOG_FLAG_CONS_MOUSE) 113#define ZS_IS_CONS(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CONS) 114#define ZS_IS_KGDB(UP) ((UP)->flags & SUNZILOG_FLAG_IS_KGDB) 115#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & SUNZILOG_FLAG_MODEM_STATUS) 116#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & SUNZILOG_FLAG_IS_CHANNEL_A) 117#define ZS_REGS_HELD(UP) ((UP)->flags & SUNZILOG_FLAG_REGS_HELD) 118#define ZS_TX_STOPPED(UP) ((UP)->flags & SUNZILOG_FLAG_TX_STOPPED) 119#define ZS_TX_ACTIVE(UP) ((UP)->flags & SUNZILOG_FLAG_TX_ACTIVE) 120 121/* Reading and writing Zilog8530 registers. The delays are to make this 122 * driver work on the Sun4 which needs a settling delay after each chip 123 * register access, other machines handle this in hardware via auxiliary 124 * flip-flops which implement the settle time we do in software. 125 * 126 * The port lock must be held and local IRQs must be disabled 127 * when {read,write}_zsreg is invoked. 128 */ 129static unsigned char read_zsreg(struct zilog_channel __iomem *channel, 130 unsigned char reg) 131{ 132 unsigned char retval; 133 134 writeb(reg, &channel->control); 135 ZSDELAY(); 136 retval = readb(&channel->control); 137 ZSDELAY(); 138 139 return retval; 140} 141 142static void write_zsreg(struct zilog_channel __iomem *channel, 143 unsigned char reg, unsigned char value) 144{ 145 writeb(reg, &channel->control); 146 ZSDELAY(); 147 writeb(value, &channel->control); 148 ZSDELAY(); 149} 150 151static void sunzilog_clear_fifo(struct zilog_channel __iomem *channel) 152{ 153 int i; 154 155 for (i = 0; i < 32; i++) { 156 unsigned char regval; 157 158 regval = readb(&channel->control); 159 ZSDELAY(); 160 if (regval & Rx_CH_AV) 161 break; 162 163 regval = read_zsreg(channel, R1); 164 readb(&channel->data); 165 ZSDELAY(); 166 167 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) { 168 writeb(ERR_RES, &channel->control); 169 ZSDELAY(); 170 ZS_WSYNC(channel); 171 } 172 } 173} 174 175/* This function must only be called when the TX is not busy. The UART 176 * port lock must be held and local interrupts disabled. 177 */ 178static int __load_zsregs(struct zilog_channel __iomem *channel, unsigned char *regs) 179{ 180 int i; 181 int escc; 182 unsigned char r15; 183 184 /* Let pending transmits finish. */ 185 for (i = 0; i < 1000; i++) { 186 unsigned char stat = read_zsreg(channel, R1); 187 if (stat & ALL_SNT) 188 break; 189 udelay(100); 190 } 191 192 writeb(ERR_RES, &channel->control); 193 ZSDELAY(); 194 ZS_WSYNC(channel); 195 196 sunzilog_clear_fifo(channel); 197 198 /* Disable all interrupts. */ 199 write_zsreg(channel, R1, 200 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); 201 202 /* Set parity, sync config, stop bits, and clock divisor. */ 203 write_zsreg(channel, R4, regs[R4]); 204 205 /* Set misc. TX/RX control bits. */ 206 write_zsreg(channel, R10, regs[R10]); 207 208 /* Set TX/RX controls sans the enable bits. */ 209 write_zsreg(channel, R3, regs[R3] & ~RxENAB); 210 write_zsreg(channel, R5, regs[R5] & ~TxENAB); 211 212 /* Synchronous mode config. */ 213 write_zsreg(channel, R6, regs[R6]); 214 write_zsreg(channel, R7, regs[R7]); 215 216 /* Don't mess with the interrupt vector (R2, unused by us) and 217 * master interrupt control (R9). We make sure this is setup 218 * properly at probe time then never touch it again. 219 */ 220 221 /* Disable baud generator. */ 222 write_zsreg(channel, R14, regs[R14] & ~BRENAB); 223 224 /* Clock mode control. */ 225 write_zsreg(channel, R11, regs[R11]); 226 227 /* Lower and upper byte of baud rate generator divisor. */ 228 write_zsreg(channel, R12, regs[R12]); 229 write_zsreg(channel, R13, regs[R13]); 230 231 /* Now rewrite R14, with BRENAB (if set). */ 232 write_zsreg(channel, R14, regs[R14]); 233 234 /* External status interrupt control. */ 235 write_zsreg(channel, R15, (regs[R15] | WR7pEN) & ~FIFOEN); 236 237 /* ESCC Extension Register */ 238 r15 = read_zsreg(channel, R15); 239 if (r15 & 0x01) { 240 write_zsreg(channel, R7, regs[R7p]); 241 242 /* External status interrupt and FIFO control. */ 243 write_zsreg(channel, R15, regs[R15] & ~WR7pEN); 244 escc = 1; 245 } else { 246 /* Clear FIFO bit case it is an issue */ 247 regs[R15] &= ~FIFOEN; 248 escc = 0; 249 } 250 251 /* Reset external status interrupts. */ 252 write_zsreg(channel, R0, RES_EXT_INT); /* First Latch */ 253 write_zsreg(channel, R0, RES_EXT_INT); /* Second Latch */ 254 255 /* Rewrite R3/R5, this time without enables masked. */ 256 write_zsreg(channel, R3, regs[R3]); 257 write_zsreg(channel, R5, regs[R5]); 258 259 /* Rewrite R1, this time without IRQ enabled masked. */ 260 write_zsreg(channel, R1, regs[R1]); 261 262 return escc; 263} 264 265/* Reprogram the Zilog channel HW registers with the copies found in the 266 * software state struct. If the transmitter is busy, we defer this update 267 * until the next TX complete interrupt. Else, we do it right now. 268 * 269 * The UART port lock must be held and local interrupts disabled. 270 */ 271static void sunzilog_maybe_update_regs(struct uart_sunzilog_port *up, 272 struct zilog_channel __iomem *channel) 273{ 274 if (!ZS_REGS_HELD(up)) { 275 if (ZS_TX_ACTIVE(up)) { 276 up->flags |= SUNZILOG_FLAG_REGS_HELD; 277 } else { 278 __load_zsregs(channel, up->curregs); 279 } 280 } 281} 282 283static void sunzilog_change_mouse_baud(struct uart_sunzilog_port *up) 284{ 285 unsigned int cur_cflag = up->cflag; 286 int brg, new_baud; 287 288 up->cflag &= ~CBAUD; 289 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud); 290 291 brg = BPS_TO_BRG(new_baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 292 up->curregs[R12] = (brg & 0xff); 293 up->curregs[R13] = (brg >> 8) & 0xff; 294 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(&up->port)); 295} 296 297static void sunzilog_kbdms_receive_chars(struct uart_sunzilog_port *up, 298 unsigned char ch, int is_break) 299{ 300 if (ZS_IS_KEYB(up)) { 301 /* Stop-A is handled by drivers/char/keyboard.c now. */ 302#ifdef CONFIG_SERIO 303 if (up->serio_open) 304 serio_interrupt(&up->serio, ch, 0); 305#endif 306 } else if (ZS_IS_MOUSE(up)) { 307 int ret = suncore_mouse_baud_detection(ch, is_break); 308 309 switch (ret) { 310 case 2: 311 sunzilog_change_mouse_baud(up); 312 /* fallthru */ 313 case 1: 314 break; 315 316 case 0: 317#ifdef CONFIG_SERIO 318 if (up->serio_open) 319 serio_interrupt(&up->serio, ch, 0); 320#endif 321 break; 322 } 323 } 324} 325 326static struct tty_port * 327sunzilog_receive_chars(struct uart_sunzilog_port *up, 328 struct zilog_channel __iomem *channel) 329{ 330 struct tty_port *port = NULL; 331 unsigned char ch, r1, flag; 332 333 if (up->port.state != NULL) /* Unopened serial console */ 334 port = &up->port.state->port; 335 336 for (;;) { 337 338 r1 = read_zsreg(channel, R1); 339 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 340 writeb(ERR_RES, &channel->control); 341 ZSDELAY(); 342 ZS_WSYNC(channel); 343 } 344 345 ch = readb(&channel->control); 346 ZSDELAY(); 347 348 /* This funny hack depends upon BRK_ABRT not interfering 349 * with the other bits we care about in R1. 350 */ 351 if (ch & BRK_ABRT) 352 r1 |= BRK_ABRT; 353 354 if (!(ch & Rx_CH_AV)) 355 break; 356 357 ch = readb(&channel->data); 358 ZSDELAY(); 359 360 ch &= up->parity_mask; 361 362 if (unlikely(ZS_IS_KEYB(up)) || unlikely(ZS_IS_MOUSE(up))) { 363 sunzilog_kbdms_receive_chars(up, ch, 0); 364 continue; 365 } 366 367 /* A real serial line, record the character and status. */ 368 flag = TTY_NORMAL; 369 up->port.icount.rx++; 370 if (r1 & (BRK_ABRT | PAR_ERR | Rx_OVR | CRC_ERR)) { 371 if (r1 & BRK_ABRT) { 372 r1 &= ~(PAR_ERR | CRC_ERR); 373 up->port.icount.brk++; 374 if (uart_handle_break(&up->port)) 375 continue; 376 } 377 else if (r1 & PAR_ERR) 378 up->port.icount.parity++; 379 else if (r1 & CRC_ERR) 380 up->port.icount.frame++; 381 if (r1 & Rx_OVR) 382 up->port.icount.overrun++; 383 r1 &= up->port.read_status_mask; 384 if (r1 & BRK_ABRT) 385 flag = TTY_BREAK; 386 else if (r1 & PAR_ERR) 387 flag = TTY_PARITY; 388 else if (r1 & CRC_ERR) 389 flag = TTY_FRAME; 390 } 391 if (uart_handle_sysrq_char(&up->port, ch) || !port) 392 continue; 393 394 if (up->port.ignore_status_mask == 0xff || 395 (r1 & up->port.ignore_status_mask) == 0) { 396 tty_insert_flip_char(port, ch, flag); 397 } 398 if (r1 & Rx_OVR) 399 tty_insert_flip_char(port, 0, TTY_OVERRUN); 400 } 401 402 return port; 403} 404 405static void sunzilog_status_handle(struct uart_sunzilog_port *up, 406 struct zilog_channel __iomem *channel) 407{ 408 unsigned char status; 409 410 status = readb(&channel->control); 411 ZSDELAY(); 412 413 writeb(RES_EXT_INT, &channel->control); 414 ZSDELAY(); 415 ZS_WSYNC(channel); 416 417 if (status & BRK_ABRT) { 418 if (ZS_IS_MOUSE(up)) 419 sunzilog_kbdms_receive_chars(up, 0, 1); 420 if (ZS_IS_CONS(up)) { 421 /* Wait for BREAK to deassert to avoid potentially 422 * confusing the PROM. 423 */ 424 while (1) { 425 status = readb(&channel->control); 426 ZSDELAY(); 427 if (!(status & BRK_ABRT)) 428 break; 429 } 430 sun_do_break(); 431 return; 432 } 433 } 434 435 if (ZS_WANTS_MODEM_STATUS(up)) { 436 if (status & SYNC) 437 up->port.icount.dsr++; 438 439 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. 440 * But it does not tell us which bit has changed, we have to keep 441 * track of this ourselves. 442 */ 443 if ((status ^ up->prev_status) ^ DCD) 444 uart_handle_dcd_change(&up->port, 445 (status & DCD)); 446 if ((status ^ up->prev_status) ^ CTS) 447 uart_handle_cts_change(&up->port, 448 (status & CTS)); 449 450 wake_up_interruptible(&up->port.state->port.delta_msr_wait); 451 } 452 453 up->prev_status = status; 454} 455 456static void sunzilog_transmit_chars(struct uart_sunzilog_port *up, 457 struct zilog_channel __iomem *channel) 458{ 459 struct circ_buf *xmit; 460 461 if (ZS_IS_CONS(up)) { 462 unsigned char status = readb(&channel->control); 463 ZSDELAY(); 464 465 /* TX still busy? Just wait for the next TX done interrupt. 466 * 467 * It can occur because of how we do serial console writes. It would 468 * be nice to transmit console writes just like we normally would for 469 * a TTY line. (ie. buffered and TX interrupt driven). That is not 470 * easy because console writes cannot sleep. One solution might be 471 * to poll on enough port->xmit space becoming free. -DaveM 472 */ 473 if (!(status & Tx_BUF_EMP)) 474 return; 475 } 476 477 up->flags &= ~SUNZILOG_FLAG_TX_ACTIVE; 478 479 if (ZS_REGS_HELD(up)) { 480 __load_zsregs(channel, up->curregs); 481 up->flags &= ~SUNZILOG_FLAG_REGS_HELD; 482 } 483 484 if (ZS_TX_STOPPED(up)) { 485 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 486 goto ack_tx_int; 487 } 488 489 if (up->port.x_char) { 490 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 491 writeb(up->port.x_char, &channel->data); 492 ZSDELAY(); 493 ZS_WSYNC(channel); 494 495 up->port.icount.tx++; 496 up->port.x_char = 0; 497 return; 498 } 499 500 if (up->port.state == NULL) 501 goto ack_tx_int; 502 xmit = &up->port.state->xmit; 503 if (uart_circ_empty(xmit)) 504 goto ack_tx_int; 505 506 if (uart_tx_stopped(&up->port)) 507 goto ack_tx_int; 508 509 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 510 writeb(xmit->buf[xmit->tail], &channel->data); 511 ZSDELAY(); 512 ZS_WSYNC(channel); 513 514 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 515 up->port.icount.tx++; 516 517 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 518 uart_write_wakeup(&up->port); 519 520 return; 521 522ack_tx_int: 523 writeb(RES_Tx_P, &channel->control); 524 ZSDELAY(); 525 ZS_WSYNC(channel); 526} 527 528static irqreturn_t sunzilog_interrupt(int irq, void *dev_id) 529{ 530 struct uart_sunzilog_port *up = dev_id; 531 532 while (up) { 533 struct zilog_channel __iomem *channel 534 = ZILOG_CHANNEL_FROM_PORT(&up->port); 535 struct tty_port *port; 536 unsigned char r3; 537 538 spin_lock(&up->port.lock); 539 r3 = read_zsreg(channel, R3); 540 541 /* Channel A */ 542 port = NULL; 543 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { 544 writeb(RES_H_IUS, &channel->control); 545 ZSDELAY(); 546 ZS_WSYNC(channel); 547 548 if (r3 & CHARxIP) 549 port = sunzilog_receive_chars(up, channel); 550 if (r3 & CHAEXT) 551 sunzilog_status_handle(up, channel); 552 if (r3 & CHATxIP) 553 sunzilog_transmit_chars(up, channel); 554 } 555 spin_unlock(&up->port.lock); 556 557 if (port) 558 tty_flip_buffer_push(port); 559 560 /* Channel B */ 561 up = up->next; 562 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 563 564 spin_lock(&up->port.lock); 565 port = NULL; 566 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { 567 writeb(RES_H_IUS, &channel->control); 568 ZSDELAY(); 569 ZS_WSYNC(channel); 570 571 if (r3 & CHBRxIP) 572 port = sunzilog_receive_chars(up, channel); 573 if (r3 & CHBEXT) 574 sunzilog_status_handle(up, channel); 575 if (r3 & CHBTxIP) 576 sunzilog_transmit_chars(up, channel); 577 } 578 spin_unlock(&up->port.lock); 579 580 if (port) 581 tty_flip_buffer_push(port); 582 583 up = up->next; 584 } 585 586 return IRQ_HANDLED; 587} 588 589/* A convenient way to quickly get R0 status. The caller must _not_ hold the 590 * port lock, it is acquired here. 591 */ 592static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port) 593{ 594 struct zilog_channel __iomem *channel; 595 unsigned char status; 596 597 channel = ZILOG_CHANNEL_FROM_PORT(port); 598 status = readb(&channel->control); 599 ZSDELAY(); 600 601 return status; 602} 603 604/* The port lock is not held. */ 605static unsigned int sunzilog_tx_empty(struct uart_port *port) 606{ 607 unsigned long flags; 608 unsigned char status; 609 unsigned int ret; 610 611 spin_lock_irqsave(&port->lock, flags); 612 613 status = sunzilog_read_channel_status(port); 614 615 spin_unlock_irqrestore(&port->lock, flags); 616 617 if (status & Tx_BUF_EMP) 618 ret = TIOCSER_TEMT; 619 else 620 ret = 0; 621 622 return ret; 623} 624 625/* The port lock is held and interrupts are disabled. */ 626static unsigned int sunzilog_get_mctrl(struct uart_port *port) 627{ 628 unsigned char status; 629 unsigned int ret; 630 631 status = sunzilog_read_channel_status(port); 632 633 ret = 0; 634 if (status & DCD) 635 ret |= TIOCM_CAR; 636 if (status & SYNC) 637 ret |= TIOCM_DSR; 638 if (status & CTS) 639 ret |= TIOCM_CTS; 640 641 return ret; 642} 643 644/* The port lock is held and interrupts are disabled. */ 645static void sunzilog_set_mctrl(struct uart_port *port, unsigned int mctrl) 646{ 647 struct uart_sunzilog_port *up = 648 container_of(port, struct uart_sunzilog_port, port); 649 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 650 unsigned char set_bits, clear_bits; 651 652 set_bits = clear_bits = 0; 653 654 if (mctrl & TIOCM_RTS) 655 set_bits |= RTS; 656 else 657 clear_bits |= RTS; 658 if (mctrl & TIOCM_DTR) 659 set_bits |= DTR; 660 else 661 clear_bits |= DTR; 662 663 /* NOTE: Not subject to 'transmitter active' rule. */ 664 up->curregs[R5] |= set_bits; 665 up->curregs[R5] &= ~clear_bits; 666 write_zsreg(channel, R5, up->curregs[R5]); 667} 668 669/* The port lock is held and interrupts are disabled. */ 670static void sunzilog_stop_tx(struct uart_port *port) 671{ 672 struct uart_sunzilog_port *up = 673 container_of(port, struct uart_sunzilog_port, port); 674 675 up->flags |= SUNZILOG_FLAG_TX_STOPPED; 676} 677 678/* The port lock is held and interrupts are disabled. */ 679static void sunzilog_start_tx(struct uart_port *port) 680{ 681 struct uart_sunzilog_port *up = 682 container_of(port, struct uart_sunzilog_port, port); 683 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 684 unsigned char status; 685 686 up->flags |= SUNZILOG_FLAG_TX_ACTIVE; 687 up->flags &= ~SUNZILOG_FLAG_TX_STOPPED; 688 689 status = readb(&channel->control); 690 ZSDELAY(); 691 692 /* TX busy? Just wait for the TX done interrupt. */ 693 if (!(status & Tx_BUF_EMP)) 694 return; 695 696 /* Send the first character to jump-start the TX done 697 * IRQ sending engine. 698 */ 699 if (port->x_char) { 700 writeb(port->x_char, &channel->data); 701 ZSDELAY(); 702 ZS_WSYNC(channel); 703 704 port->icount.tx++; 705 port->x_char = 0; 706 } else { 707 struct circ_buf *xmit = &port->state->xmit; 708 709 if (uart_circ_empty(xmit)) 710 return; 711 writeb(xmit->buf[xmit->tail], &channel->data); 712 ZSDELAY(); 713 ZS_WSYNC(channel); 714 715 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 716 port->icount.tx++; 717 718 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 719 uart_write_wakeup(&up->port); 720 } 721} 722 723/* The port lock is held. */ 724static void sunzilog_stop_rx(struct uart_port *port) 725{ 726 struct uart_sunzilog_port *up = UART_ZILOG(port); 727 struct zilog_channel __iomem *channel; 728 729 if (ZS_IS_CONS(up)) 730 return; 731 732 channel = ZILOG_CHANNEL_FROM_PORT(port); 733 734 /* Disable all RX interrupts. */ 735 up->curregs[R1] &= ~RxINT_MASK; 736 sunzilog_maybe_update_regs(up, channel); 737} 738 739/* The port lock is held. */ 740static void sunzilog_enable_ms(struct uart_port *port) 741{ 742 struct uart_sunzilog_port *up = 743 container_of(port, struct uart_sunzilog_port, port); 744 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 745 unsigned char new_reg; 746 747 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE); 748 if (new_reg != up->curregs[R15]) { 749 up->curregs[R15] = new_reg; 750 751 /* NOTE: Not subject to 'transmitter active' rule. */ 752 write_zsreg(channel, R15, up->curregs[R15] & ~WR7pEN); 753 } 754} 755 756/* The port lock is not held. */ 757static void sunzilog_break_ctl(struct uart_port *port, int break_state) 758{ 759 struct uart_sunzilog_port *up = 760 container_of(port, struct uart_sunzilog_port, port); 761 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 762 unsigned char set_bits, clear_bits, new_reg; 763 unsigned long flags; 764 765 set_bits = clear_bits = 0; 766 767 if (break_state) 768 set_bits |= SND_BRK; 769 else 770 clear_bits |= SND_BRK; 771 772 spin_lock_irqsave(&port->lock, flags); 773 774 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits; 775 if (new_reg != up->curregs[R5]) { 776 up->curregs[R5] = new_reg; 777 778 /* NOTE: Not subject to 'transmitter active' rule. */ 779 write_zsreg(channel, R5, up->curregs[R5]); 780 } 781 782 spin_unlock_irqrestore(&port->lock, flags); 783} 784 785static void __sunzilog_startup(struct uart_sunzilog_port *up) 786{ 787 struct zilog_channel __iomem *channel; 788 789 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 790 up->prev_status = readb(&channel->control); 791 792 /* Enable receiver and transmitter. */ 793 up->curregs[R3] |= RxENAB; 794 up->curregs[R5] |= TxENAB; 795 796 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 797 sunzilog_maybe_update_regs(up, channel); 798} 799 800static int sunzilog_startup(struct uart_port *port) 801{ 802 struct uart_sunzilog_port *up = UART_ZILOG(port); 803 unsigned long flags; 804 805 if (ZS_IS_CONS(up)) 806 return 0; 807 808 spin_lock_irqsave(&port->lock, flags); 809 __sunzilog_startup(up); 810 spin_unlock_irqrestore(&port->lock, flags); 811 return 0; 812} 813 814/* 815 * The test for ZS_IS_CONS is explained by the following e-mail: 816 ***** 817 * From: Russell King <rmk@arm.linux.org.uk> 818 * Date: Sun, 8 Dec 2002 10:18:38 +0000 819 * 820 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote: 821 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument, 822 * > and I noticed that something is not right with reference 823 * > counting in this case. It seems that when the console 824 * > is open by kernel initially, this is not accounted 825 * > as an open, and uart_startup is not called. 826 * 827 * That is correct. We are unable to call uart_startup when the serial 828 * console is initialised because it may need to allocate memory (as 829 * request_irq does) and the memory allocators may not have been 830 * initialised. 831 * 832 * 1. initialise the port into a state where it can send characters in the 833 * console write method. 834 * 835 * 2. don't do the actual hardware shutdown in your shutdown() method (but 836 * do the normal software shutdown - ie, free irqs etc) 837 ***** 838 */ 839static void sunzilog_shutdown(struct uart_port *port) 840{ 841 struct uart_sunzilog_port *up = UART_ZILOG(port); 842 struct zilog_channel __iomem *channel; 843 unsigned long flags; 844 845 if (ZS_IS_CONS(up)) 846 return; 847 848 spin_lock_irqsave(&port->lock, flags); 849 850 channel = ZILOG_CHANNEL_FROM_PORT(port); 851 852 /* Disable receiver and transmitter. */ 853 up->curregs[R3] &= ~RxENAB; 854 up->curregs[R5] &= ~TxENAB; 855 856 /* Disable all interrupts and BRK assertion. */ 857 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); 858 up->curregs[R5] &= ~SND_BRK; 859 sunzilog_maybe_update_regs(up, channel); 860 861 spin_unlock_irqrestore(&port->lock, flags); 862} 863 864/* Shared by TTY driver and serial console setup. The port lock is held 865 * and local interrupts are disabled. 866 */ 867static void 868sunzilog_convert_to_zs(struct uart_sunzilog_port *up, unsigned int cflag, 869 unsigned int iflag, int brg) 870{ 871 872 up->curregs[R10] = NRZ; 873 up->curregs[R11] = TCBR | RCBR; 874 875 /* Program BAUD and clock source. */ 876 up->curregs[R4] &= ~XCLK_MASK; 877 up->curregs[R4] |= X16CLK; 878 up->curregs[R12] = brg & 0xff; 879 up->curregs[R13] = (brg >> 8) & 0xff; 880 up->curregs[R14] = BRSRC | BRENAB; 881 882 /* Character size, stop bits, and parity. */ 883 up->curregs[R3] &= ~RxN_MASK; 884 up->curregs[R5] &= ~TxN_MASK; 885 switch (cflag & CSIZE) { 886 case CS5: 887 up->curregs[R3] |= Rx5; 888 up->curregs[R5] |= Tx5; 889 up->parity_mask = 0x1f; 890 break; 891 case CS6: 892 up->curregs[R3] |= Rx6; 893 up->curregs[R5] |= Tx6; 894 up->parity_mask = 0x3f; 895 break; 896 case CS7: 897 up->curregs[R3] |= Rx7; 898 up->curregs[R5] |= Tx7; 899 up->parity_mask = 0x7f; 900 break; 901 case CS8: 902 default: 903 up->curregs[R3] |= Rx8; 904 up->curregs[R5] |= Tx8; 905 up->parity_mask = 0xff; 906 break; 907 } 908 up->curregs[R4] &= ~0x0c; 909 if (cflag & CSTOPB) 910 up->curregs[R4] |= SB2; 911 else 912 up->curregs[R4] |= SB1; 913 if (cflag & PARENB) 914 up->curregs[R4] |= PAR_ENAB; 915 else 916 up->curregs[R4] &= ~PAR_ENAB; 917 if (!(cflag & PARODD)) 918 up->curregs[R4] |= PAR_EVEN; 919 else 920 up->curregs[R4] &= ~PAR_EVEN; 921 922 up->port.read_status_mask = Rx_OVR; 923 if (iflag & INPCK) 924 up->port.read_status_mask |= CRC_ERR | PAR_ERR; 925 if (iflag & (IGNBRK | BRKINT | PARMRK)) 926 up->port.read_status_mask |= BRK_ABRT; 927 928 up->port.ignore_status_mask = 0; 929 if (iflag & IGNPAR) 930 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR; 931 if (iflag & IGNBRK) { 932 up->port.ignore_status_mask |= BRK_ABRT; 933 if (iflag & IGNPAR) 934 up->port.ignore_status_mask |= Rx_OVR; 935 } 936 937 if ((cflag & CREAD) == 0) 938 up->port.ignore_status_mask = 0xff; 939} 940 941/* The port lock is not held. */ 942static void 943sunzilog_set_termios(struct uart_port *port, struct ktermios *termios, 944 struct ktermios *old) 945{ 946 struct uart_sunzilog_port *up = 947 container_of(port, struct uart_sunzilog_port, port); 948 unsigned long flags; 949 int baud, brg; 950 951 baud = uart_get_baud_rate(port, termios, old, 1200, 76800); 952 953 spin_lock_irqsave(&up->port.lock, flags); 954 955 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 956 957 sunzilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg); 958 959 if (UART_ENABLE_MS(&up->port, termios->c_cflag)) 960 up->flags |= SUNZILOG_FLAG_MODEM_STATUS; 961 else 962 up->flags &= ~SUNZILOG_FLAG_MODEM_STATUS; 963 964 up->cflag = termios->c_cflag; 965 966 sunzilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port)); 967 968 uart_update_timeout(port, termios->c_cflag, baud); 969 970 spin_unlock_irqrestore(&up->port.lock, flags); 971} 972 973static const char *sunzilog_type(struct uart_port *port) 974{ 975 struct uart_sunzilog_port *up = UART_ZILOG(port); 976 977 return (up->flags & SUNZILOG_FLAG_ESCC) ? "zs (ESCC)" : "zs"; 978} 979 980/* We do not request/release mappings of the registers here, this 981 * happens at early serial probe time. 982 */ 983static void sunzilog_release_port(struct uart_port *port) 984{ 985} 986 987static int sunzilog_request_port(struct uart_port *port) 988{ 989 return 0; 990} 991 992/* These do not need to do anything interesting either. */ 993static void sunzilog_config_port(struct uart_port *port, int flags) 994{ 995} 996 997/* We do not support letting the user mess with the divisor, IRQ, etc. */ 998static int sunzilog_verify_port(struct uart_port *port, struct serial_struct *ser) 999{ 1000 return -EINVAL; 1001} 1002 1003#ifdef CONFIG_CONSOLE_POLL 1004static int sunzilog_get_poll_char(struct uart_port *port) 1005{ 1006 unsigned char ch, r1; 1007 struct uart_sunzilog_port *up = 1008 container_of(port, struct uart_sunzilog_port, port); 1009 struct zilog_channel __iomem *channel 1010 = ZILOG_CHANNEL_FROM_PORT(&up->port); 1011 1012 1013 r1 = read_zsreg(channel, R1); 1014 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 1015 writeb(ERR_RES, &channel->control); 1016 ZSDELAY(); 1017 ZS_WSYNC(channel); 1018 } 1019 1020 ch = readb(&channel->control); 1021 ZSDELAY(); 1022 1023 /* This funny hack depends upon BRK_ABRT not interfering 1024 * with the other bits we care about in R1. 1025 */ 1026 if (ch & BRK_ABRT) 1027 r1 |= BRK_ABRT; 1028 1029 if (!(ch & Rx_CH_AV)) 1030 return NO_POLL_CHAR; 1031 1032 ch = readb(&channel->data); 1033 ZSDELAY(); 1034 1035 ch &= up->parity_mask; 1036 return ch; 1037} 1038 1039static void sunzilog_put_poll_char(struct uart_port *port, 1040 unsigned char ch) 1041{ 1042 struct uart_sunzilog_port *up = 1043 container_of(port, struct uart_sunzilog_port, port); 1044 1045 sunzilog_putchar(&up->port, ch); 1046} 1047#endif /* CONFIG_CONSOLE_POLL */ 1048 1049static struct uart_ops sunzilog_pops = { 1050 .tx_empty = sunzilog_tx_empty, 1051 .set_mctrl = sunzilog_set_mctrl, 1052 .get_mctrl = sunzilog_get_mctrl, 1053 .stop_tx = sunzilog_stop_tx, 1054 .start_tx = sunzilog_start_tx, 1055 .stop_rx = sunzilog_stop_rx, 1056 .enable_ms = sunzilog_enable_ms, 1057 .break_ctl = sunzilog_break_ctl, 1058 .startup = sunzilog_startup, 1059 .shutdown = sunzilog_shutdown, 1060 .set_termios = sunzilog_set_termios, 1061 .type = sunzilog_type, 1062 .release_port = sunzilog_release_port, 1063 .request_port = sunzilog_request_port, 1064 .config_port = sunzilog_config_port, 1065 .verify_port = sunzilog_verify_port, 1066#ifdef CONFIG_CONSOLE_POLL 1067 .poll_get_char = sunzilog_get_poll_char, 1068 .poll_put_char = sunzilog_put_poll_char, 1069#endif 1070}; 1071 1072static int uart_chip_count; 1073static struct uart_sunzilog_port *sunzilog_port_table; 1074static struct zilog_layout __iomem **sunzilog_chip_regs; 1075 1076static struct uart_sunzilog_port *sunzilog_irq_chain; 1077 1078static struct uart_driver sunzilog_reg = { 1079 .owner = THIS_MODULE, 1080 .driver_name = "sunzilog", 1081 .dev_name = "ttyS", 1082 .major = TTY_MAJOR, 1083}; 1084 1085static int __init sunzilog_alloc_tables(int num_sunzilog) 1086{ 1087 struct uart_sunzilog_port *up; 1088 unsigned long size; 1089 int num_channels = num_sunzilog * 2; 1090 int i; 1091 1092 size = num_channels * sizeof(struct uart_sunzilog_port); 1093 sunzilog_port_table = kzalloc(size, GFP_KERNEL); 1094 if (!sunzilog_port_table) 1095 return -ENOMEM; 1096 1097 for (i = 0; i < num_channels; i++) { 1098 up = &sunzilog_port_table[i]; 1099 1100 spin_lock_init(&up->port.lock); 1101 1102 if (i == 0) 1103 sunzilog_irq_chain = up; 1104 1105 if (i < num_channels - 1) 1106 up->next = up + 1; 1107 else 1108 up->next = NULL; 1109 } 1110 1111 size = num_sunzilog * sizeof(struct zilog_layout __iomem *); 1112 sunzilog_chip_regs = kzalloc(size, GFP_KERNEL); 1113 if (!sunzilog_chip_regs) { 1114 kfree(sunzilog_port_table); 1115 sunzilog_irq_chain = NULL; 1116 return -ENOMEM; 1117 } 1118 1119 return 0; 1120} 1121 1122static void sunzilog_free_tables(void) 1123{ 1124 kfree(sunzilog_port_table); 1125 sunzilog_irq_chain = NULL; 1126 kfree(sunzilog_chip_regs); 1127} 1128 1129#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */ 1130 1131static void sunzilog_putchar(struct uart_port *port, int ch) 1132{ 1133 struct zilog_channel __iomem *channel = ZILOG_CHANNEL_FROM_PORT(port); 1134 int loops = ZS_PUT_CHAR_MAX_DELAY; 1135 1136 /* This is a timed polling loop so do not switch the explicit 1137 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM 1138 */ 1139 do { 1140 unsigned char val = readb(&channel->control); 1141 if (val & Tx_BUF_EMP) { 1142 ZSDELAY(); 1143 break; 1144 } 1145 udelay(5); 1146 } while (--loops); 1147 1148 writeb(ch, &channel->data); 1149 ZSDELAY(); 1150 ZS_WSYNC(channel); 1151} 1152 1153#ifdef CONFIG_SERIO 1154 1155static DEFINE_SPINLOCK(sunzilog_serio_lock); 1156 1157static int sunzilog_serio_write(struct serio *serio, unsigned char ch) 1158{ 1159 struct uart_sunzilog_port *up = serio->port_data; 1160 unsigned long flags; 1161 1162 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1163 1164 sunzilog_putchar(&up->port, ch); 1165 1166 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1167 1168 return 0; 1169} 1170 1171static int sunzilog_serio_open(struct serio *serio) 1172{ 1173 struct uart_sunzilog_port *up = serio->port_data; 1174 unsigned long flags; 1175 int ret; 1176 1177 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1178 if (!up->serio_open) { 1179 up->serio_open = 1; 1180 ret = 0; 1181 } else 1182 ret = -EBUSY; 1183 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1184 1185 return ret; 1186} 1187 1188static void sunzilog_serio_close(struct serio *serio) 1189{ 1190 struct uart_sunzilog_port *up = serio->port_data; 1191 unsigned long flags; 1192 1193 spin_lock_irqsave(&sunzilog_serio_lock, flags); 1194 up->serio_open = 0; 1195 spin_unlock_irqrestore(&sunzilog_serio_lock, flags); 1196} 1197 1198#endif /* CONFIG_SERIO */ 1199 1200#ifdef CONFIG_SERIAL_SUNZILOG_CONSOLE 1201static void 1202sunzilog_console_write(struct console *con, const char *s, unsigned int count) 1203{ 1204 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1205 unsigned long flags; 1206 int locked = 1; 1207 1208 if (up->port.sysrq || oops_in_progress) 1209 locked = spin_trylock_irqsave(&up->port.lock, flags); 1210 else 1211 spin_lock_irqsave(&up->port.lock, flags); 1212 1213 uart_console_write(&up->port, s, count, sunzilog_putchar); 1214 udelay(2); 1215 1216 if (locked) 1217 spin_unlock_irqrestore(&up->port.lock, flags); 1218} 1219 1220static int __init sunzilog_console_setup(struct console *con, char *options) 1221{ 1222 struct uart_sunzilog_port *up = &sunzilog_port_table[con->index]; 1223 unsigned long flags; 1224 int baud, brg; 1225 1226 if (up->port.type != PORT_SUNZILOG) 1227 return -1; 1228 1229 printk(KERN_INFO "Console: ttyS%d (SunZilog zs%d)\n", 1230 (sunzilog_reg.minor - 64) + con->index, con->index); 1231 1232 /* Get firmware console settings. */ 1233 sunserial_console_termios(con, up->port.dev->of_node); 1234 1235 /* Firmware console speed is limited to 150-->38400 baud so 1236 * this hackish cflag thing is OK. 1237 */ 1238 switch (con->cflag & CBAUD) { 1239 case B150: baud = 150; break; 1240 case B300: baud = 300; break; 1241 case B600: baud = 600; break; 1242 case B1200: baud = 1200; break; 1243 case B2400: baud = 2400; break; 1244 case B4800: baud = 4800; break; 1245 default: case B9600: baud = 9600; break; 1246 case B19200: baud = 19200; break; 1247 case B38400: baud = 38400; break; 1248 } 1249 1250 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1251 1252 spin_lock_irqsave(&up->port.lock, flags); 1253 1254 up->curregs[R15] |= BRKIE; 1255 sunzilog_convert_to_zs(up, con->cflag, 0, brg); 1256 1257 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1258 __sunzilog_startup(up); 1259 1260 spin_unlock_irqrestore(&up->port.lock, flags); 1261 1262 return 0; 1263} 1264 1265static struct console sunzilog_console_ops = { 1266 .name = "ttyS", 1267 .write = sunzilog_console_write, 1268 .device = uart_console_device, 1269 .setup = sunzilog_console_setup, 1270 .flags = CON_PRINTBUFFER, 1271 .index = -1, 1272 .data = &sunzilog_reg, 1273}; 1274 1275static inline struct console *SUNZILOG_CONSOLE(void) 1276{ 1277 return &sunzilog_console_ops; 1278} 1279 1280#else 1281#define SUNZILOG_CONSOLE() (NULL) 1282#endif 1283 1284static void sunzilog_init_kbdms(struct uart_sunzilog_port *up) 1285{ 1286 int baud, brg; 1287 1288 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1289 up->cflag = B1200 | CS8 | CLOCAL | CREAD; 1290 baud = 1200; 1291 } else { 1292 up->cflag = B4800 | CS8 | CLOCAL | CREAD; 1293 baud = 4800; 1294 } 1295 1296 up->curregs[R15] |= BRKIE; 1297 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1298 sunzilog_convert_to_zs(up, up->cflag, 0, brg); 1299 sunzilog_set_mctrl(&up->port, TIOCM_DTR | TIOCM_RTS); 1300 __sunzilog_startup(up); 1301} 1302 1303#ifdef CONFIG_SERIO 1304static void sunzilog_register_serio(struct uart_sunzilog_port *up) 1305{ 1306 struct serio *serio = &up->serio; 1307 1308 serio->port_data = up; 1309 1310 serio->id.type = SERIO_RS232; 1311 if (up->flags & SUNZILOG_FLAG_CONS_KEYB) { 1312 serio->id.proto = SERIO_SUNKBD; 1313 strlcpy(serio->name, "zskbd", sizeof(serio->name)); 1314 } else { 1315 serio->id.proto = SERIO_SUN; 1316 serio->id.extra = 1; 1317 strlcpy(serio->name, "zsms", sizeof(serio->name)); 1318 } 1319 strlcpy(serio->phys, 1320 ((up->flags & SUNZILOG_FLAG_CONS_KEYB) ? 1321 "zs/serio0" : "zs/serio1"), 1322 sizeof(serio->phys)); 1323 1324 serio->write = sunzilog_serio_write; 1325 serio->open = sunzilog_serio_open; 1326 serio->close = sunzilog_serio_close; 1327 serio->dev.parent = up->port.dev; 1328 1329 serio_register_port(serio); 1330} 1331#endif 1332 1333static void sunzilog_init_hw(struct uart_sunzilog_port *up) 1334{ 1335 struct zilog_channel __iomem *channel; 1336 unsigned long flags; 1337 int baud, brg; 1338 1339 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1340 1341 spin_lock_irqsave(&up->port.lock, flags); 1342 if (ZS_IS_CHANNEL_A(up)) { 1343 write_zsreg(channel, R9, FHWRES); 1344 ZSDELAY_LONG(); 1345 (void) read_zsreg(channel, R0); 1346 } 1347 1348 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1349 SUNZILOG_FLAG_CONS_MOUSE)) { 1350 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1351 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1352 up->curregs[R3] = RxENAB | Rx8; 1353 up->curregs[R5] = TxENAB | Tx8; 1354 up->curregs[R6] = 0x00; /* SDLC Address */ 1355 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1356 up->curregs[R9] = NV; 1357 up->curregs[R7p] = 0x00; 1358 sunzilog_init_kbdms(up); 1359 /* Only enable interrupts if an ISR handler available */ 1360 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1361 up->curregs[R9] |= MIE; 1362 write_zsreg(channel, R9, up->curregs[R9]); 1363 } else { 1364 /* Normal serial TTY. */ 1365 up->parity_mask = 0xff; 1366 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB; 1367 up->curregs[R4] = PAR_EVEN | X16CLK | SB1; 1368 up->curregs[R3] = RxENAB | Rx8; 1369 up->curregs[R5] = TxENAB | Tx8; 1370 up->curregs[R6] = 0x00; /* SDLC Address */ 1371 up->curregs[R7] = 0x7E; /* SDLC Flag */ 1372 up->curregs[R9] = NV; 1373 up->curregs[R10] = NRZ; 1374 up->curregs[R11] = TCBR | RCBR; 1375 baud = 9600; 1376 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR); 1377 up->curregs[R12] = (brg & 0xff); 1378 up->curregs[R13] = (brg >> 8) & 0xff; 1379 up->curregs[R14] = BRSRC | BRENAB; 1380 up->curregs[R15] = FIFOEN; /* Use FIFO if on ESCC */ 1381 up->curregs[R7p] = TxFIFO_LVL | RxFIFO_LVL; 1382 if (__load_zsregs(channel, up->curregs)) { 1383 up->flags |= SUNZILOG_FLAG_ESCC; 1384 } 1385 /* Only enable interrupts if an ISR handler available */ 1386 if (up->flags & SUNZILOG_FLAG_ISR_HANDLER) 1387 up->curregs[R9] |= MIE; 1388 write_zsreg(channel, R9, up->curregs[R9]); 1389 } 1390 1391 spin_unlock_irqrestore(&up->port.lock, flags); 1392 1393#ifdef CONFIG_SERIO 1394 if (up->flags & (SUNZILOG_FLAG_CONS_KEYB | 1395 SUNZILOG_FLAG_CONS_MOUSE)) 1396 sunzilog_register_serio(up); 1397#endif 1398} 1399 1400static int zilog_irq; 1401 1402static int zs_probe(struct platform_device *op) 1403{ 1404 static int kbm_inst, uart_inst; 1405 int inst; 1406 struct uart_sunzilog_port *up; 1407 struct zilog_layout __iomem *rp; 1408 int keyboard_mouse = 0; 1409 int err; 1410 1411 if (of_find_property(op->dev.of_node, "keyboard", NULL)) 1412 keyboard_mouse = 1; 1413 1414 /* uarts must come before keyboards/mice */ 1415 if (keyboard_mouse) 1416 inst = uart_chip_count + kbm_inst; 1417 else 1418 inst = uart_inst; 1419 1420 sunzilog_chip_regs[inst] = of_ioremap(&op->resource[0], 0, 1421 sizeof(struct zilog_layout), 1422 "zs"); 1423 if (!sunzilog_chip_regs[inst]) 1424 return -ENOMEM; 1425 1426 rp = sunzilog_chip_regs[inst]; 1427 1428 if (!zilog_irq) 1429 zilog_irq = op->archdata.irqs[0]; 1430 1431 up = &sunzilog_port_table[inst * 2]; 1432 1433 /* Channel A */ 1434 up[0].port.mapbase = op->resource[0].start + 0x00; 1435 up[0].port.membase = (void __iomem *) &rp->channelA; 1436 up[0].port.iotype = UPIO_MEM; 1437 up[0].port.irq = op->archdata.irqs[0]; 1438 up[0].port.uartclk = ZS_CLOCK; 1439 up[0].port.fifosize = 1; 1440 up[0].port.ops = &sunzilog_pops; 1441 up[0].port.type = PORT_SUNZILOG; 1442 up[0].port.flags = 0; 1443 up[0].port.line = (inst * 2) + 0; 1444 up[0].port.dev = &op->dev; 1445 up[0].flags |= SUNZILOG_FLAG_IS_CHANNEL_A; 1446 if (keyboard_mouse) 1447 up[0].flags |= SUNZILOG_FLAG_CONS_KEYB; 1448 sunzilog_init_hw(&up[0]); 1449 1450 /* Channel B */ 1451 up[1].port.mapbase = op->resource[0].start + 0x04; 1452 up[1].port.membase = (void __iomem *) &rp->channelB; 1453 up[1].port.iotype = UPIO_MEM; 1454 up[1].port.irq = op->archdata.irqs[0]; 1455 up[1].port.uartclk = ZS_CLOCK; 1456 up[1].port.fifosize = 1; 1457 up[1].port.ops = &sunzilog_pops; 1458 up[1].port.type = PORT_SUNZILOG; 1459 up[1].port.flags = 0; 1460 up[1].port.line = (inst * 2) + 1; 1461 up[1].port.dev = &op->dev; 1462 up[1].flags |= 0; 1463 if (keyboard_mouse) 1464 up[1].flags |= SUNZILOG_FLAG_CONS_MOUSE; 1465 sunzilog_init_hw(&up[1]); 1466 1467 if (!keyboard_mouse) { 1468 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1469 &sunzilog_reg, up[0].port.line, 1470 false)) 1471 up->flags |= SUNZILOG_FLAG_IS_CONS; 1472 err = uart_add_one_port(&sunzilog_reg, &up[0].port); 1473 if (err) { 1474 of_iounmap(&op->resource[0], 1475 rp, sizeof(struct zilog_layout)); 1476 return err; 1477 } 1478 if (sunserial_console_match(SUNZILOG_CONSOLE(), op->dev.of_node, 1479 &sunzilog_reg, up[1].port.line, 1480 false)) 1481 up->flags |= SUNZILOG_FLAG_IS_CONS; 1482 err = uart_add_one_port(&sunzilog_reg, &up[1].port); 1483 if (err) { 1484 uart_remove_one_port(&sunzilog_reg, &up[0].port); 1485 of_iounmap(&op->resource[0], 1486 rp, sizeof(struct zilog_layout)); 1487 return err; 1488 } 1489 uart_inst++; 1490 } else { 1491 printk(KERN_INFO "%s: Keyboard at MMIO 0x%llx (irq = %d) " 1492 "is a %s\n", 1493 dev_name(&op->dev), 1494 (unsigned long long) up[0].port.mapbase, 1495 op->archdata.irqs[0], sunzilog_type(&up[0].port)); 1496 printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) " 1497 "is a %s\n", 1498 dev_name(&op->dev), 1499 (unsigned long long) up[1].port.mapbase, 1500 op->archdata.irqs[0], sunzilog_type(&up[1].port)); 1501 kbm_inst++; 1502 } 1503 1504 platform_set_drvdata(op, &up[0]); 1505 1506 return 0; 1507} 1508 1509static void zs_remove_one(struct uart_sunzilog_port *up) 1510{ 1511 if (ZS_IS_KEYB(up) || ZS_IS_MOUSE(up)) { 1512#ifdef CONFIG_SERIO 1513 serio_unregister_port(&up->serio); 1514#endif 1515 } else 1516 uart_remove_one_port(&sunzilog_reg, &up->port); 1517} 1518 1519static int zs_remove(struct platform_device *op) 1520{ 1521 struct uart_sunzilog_port *up = platform_get_drvdata(op); 1522 struct zilog_layout __iomem *regs; 1523 1524 zs_remove_one(&up[0]); 1525 zs_remove_one(&up[1]); 1526 1527 regs = sunzilog_chip_regs[up[0].port.line / 2]; 1528 of_iounmap(&op->resource[0], regs, sizeof(struct zilog_layout)); 1529 1530 return 0; 1531} 1532 1533static const struct of_device_id zs_match[] = { 1534 { 1535 .name = "zs", 1536 }, 1537 {}, 1538}; 1539MODULE_DEVICE_TABLE(of, zs_match); 1540 1541static struct platform_driver zs_driver = { 1542 .driver = { 1543 .name = "zs", 1544 .of_match_table = zs_match, 1545 }, 1546 .probe = zs_probe, 1547 .remove = zs_remove, 1548}; 1549 1550static int __init sunzilog_init(void) 1551{ 1552 struct device_node *dp; 1553 int err; 1554 int num_keybms = 0; 1555 int num_sunzilog = 0; 1556 1557 for_each_node_by_name(dp, "zs") { 1558 num_sunzilog++; 1559 if (of_find_property(dp, "keyboard", NULL)) 1560 num_keybms++; 1561 } 1562 1563 if (num_sunzilog) { 1564 err = sunzilog_alloc_tables(num_sunzilog); 1565 if (err) 1566 goto out; 1567 1568 uart_chip_count = num_sunzilog - num_keybms; 1569 1570 err = sunserial_register_minors(&sunzilog_reg, 1571 uart_chip_count * 2); 1572 if (err) 1573 goto out_free_tables; 1574 } 1575 1576 err = platform_driver_register(&zs_driver); 1577 if (err) 1578 goto out_unregister_uart; 1579 1580 if (zilog_irq) { 1581 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1582 err = request_irq(zilog_irq, sunzilog_interrupt, IRQF_SHARED, 1583 "zs", sunzilog_irq_chain); 1584 if (err) 1585 goto out_unregister_driver; 1586 1587 /* Enable Interrupts */ 1588 while (up) { 1589 struct zilog_channel __iomem *channel; 1590 1591 /* printk (KERN_INFO "Enable IRQ for ZILOG Hardware %p\n", up); */ 1592 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1593 up->flags |= SUNZILOG_FLAG_ISR_HANDLER; 1594 up->curregs[R9] |= MIE; 1595 write_zsreg(channel, R9, up->curregs[R9]); 1596 up = up->next; 1597 } 1598 } 1599 1600out: 1601 return err; 1602 1603out_unregister_driver: 1604 platform_driver_unregister(&zs_driver); 1605 1606out_unregister_uart: 1607 if (num_sunzilog) { 1608 sunserial_unregister_minors(&sunzilog_reg, num_sunzilog); 1609 sunzilog_reg.cons = NULL; 1610 } 1611 1612out_free_tables: 1613 sunzilog_free_tables(); 1614 goto out; 1615} 1616 1617static void __exit sunzilog_exit(void) 1618{ 1619 platform_driver_unregister(&zs_driver); 1620 1621 if (zilog_irq) { 1622 struct uart_sunzilog_port *up = sunzilog_irq_chain; 1623 1624 /* Disable Interrupts */ 1625 while (up) { 1626 struct zilog_channel __iomem *channel; 1627 1628 /* printk (KERN_INFO "Disable IRQ for ZILOG Hardware %p\n", up); */ 1629 channel = ZILOG_CHANNEL_FROM_PORT(&up->port); 1630 up->flags &= ~SUNZILOG_FLAG_ISR_HANDLER; 1631 up->curregs[R9] &= ~MIE; 1632 write_zsreg(channel, R9, up->curregs[R9]); 1633 up = up->next; 1634 } 1635 1636 free_irq(zilog_irq, sunzilog_irq_chain); 1637 zilog_irq = 0; 1638 } 1639 1640 if (sunzilog_reg.nr) { 1641 sunserial_unregister_minors(&sunzilog_reg, sunzilog_reg.nr); 1642 sunzilog_free_tables(); 1643 } 1644} 1645 1646module_init(sunzilog_init); 1647module_exit(sunzilog_exit); 1648 1649MODULE_AUTHOR("David S. Miller"); 1650MODULE_DESCRIPTION("Sun Zilog serial port driver"); 1651MODULE_VERSION("2.0"); 1652MODULE_LICENSE("GPL"); 1653