1/*
2 * OMAP4 Bandgap temperature sensor driver
3 *
4 * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
5 * Contact:
6 *   Eduardo Valentin <eduardo.valentin@ti.com>
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * version 2 as published by the Free Software Foundation.
11 *
12 * This program is distributed in the hope that it will be useful, but
13 * WITHOUT ANY WARRANTY; without even the implied warranty of
14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
15 * General Public License for more details.
16 *
17 * You should have received a copy of the GNU General Public License
18 * along with this program; if not, write to the Free Software
19 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
20 * 02110-1301 USA
21 *
22 */
23#ifndef __TI_BANDGAP_H
24#define __TI_BANDGAP_H
25
26#include <linux/spinlock.h>
27#include <linux/types.h>
28#include <linux/err.h>
29
30/**
31 * DOC: bandgap driver data structure
32 * ==================================
33 *
34 *   +----------+----------------+
35 *   | struct temp_sensor_regval |
36 *   +---------------------------+
37 *              * (Array of)
38 *              |
39 *              |
40 *   +-------------------+   +-----------------+
41 *   | struct ti_bandgap |-->| struct device * |
42 *   +----------+--------+   +-----------------+
43 *              |
44 *              |
45 *              V
46 *   +------------------------+
47 *   | struct ti_bandgap_data |
48 *   +------------------------+
49 *              |
50 *              |
51 *              * (Array of)
52 * +------------+------------------------------------------------------+
53 * | +----------+------------+   +-------------------------+           |
54 * | | struct ti_temp_sensor |-->| struct temp_sensor_data |           |
55 * | +-----------------------+   +------------+------------+           |
56 * |            |                                                      |
57 * |            +                                                      |
58 * |            V                                                      |
59 * | +----------+-------------------+                                  |
60 * | | struct temp_sensor_registers |                                  |
61 * | +------------------------------+                                  |
62 * |                                                                   |
63 * +-------------------------------------------------------------------+
64 *
65 * Above is a simple diagram describing how the data structure below
66 * are organized. For each bandgap device there should be a ti_bandgap_data
67 * containing the device instance configuration, as well as, an array of
68 * sensors, representing every sensor instance present in this bandgap.
69 */
70
71/**
72 * struct temp_sensor_registers - descriptor to access registers and bitfields
73 * @temp_sensor_ctrl: TEMP_SENSOR_CTRL register offset
74 * @bgap_tempsoff_mask: mask to temp_sensor_ctrl.tempsoff
75 * @bgap_soc_mask: mask to temp_sensor_ctrl.soc
76 * @bgap_eocz_mask: mask to temp_sensor_ctrl.eocz
77 * @bgap_dtemp_mask: mask to temp_sensor_ctrl.dtemp
78 * @bgap_mask_ctrl: BANDGAP_MASK_CTRL register offset
79 * @mask_hot_mask: mask to bandgap_mask_ctrl.mask_hot
80 * @mask_cold_mask: mask to bandgap_mask_ctrl.mask_cold
81 * @mask_sidlemode_mask: mask to bandgap_mask_ctrl.mask_sidlemode
82 * @mask_counter_delay_mask: mask to bandgap_mask_ctrl.mask_counter_delay
83 * @mask_freeze_mask: mask to bandgap_mask_ctrl.mask_free
84 * @mask_clear_mask: mask to bandgap_mask_ctrl.mask_clear
85 * @mask_clear_accum_mask: mask to bandgap_mask_ctrl.mask_clear_accum
86 * @bgap_mode_ctrl: BANDGAP_MODE_CTRL register offset
87 * @mode_ctrl_mask: mask to bandgap_mode_ctrl.mode_ctrl
88 * @bgap_counter: BANDGAP_COUNTER register offset
89 * @counter_mask: mask to bandgap_counter.counter
90 * @bgap_threshold: BANDGAP_THRESHOLD register offset (TALERT thresholds)
91 * @threshold_thot_mask: mask to bandgap_threhold.thot
92 * @threshold_tcold_mask: mask to bandgap_threhold.tcold
93 * @tshut_threshold: TSHUT_THRESHOLD register offset (TSHUT thresholds)
94 * @tshut_efuse_mask: mask to tshut_threshold.tshut_efuse
95 * @tshut_efuse_shift: shift to tshut_threshold.tshut_efuse
96 * @tshut_hot_mask: mask to tshut_threhold.thot
97 * @tshut_cold_mask: mask to tshut_threhold.thot
98 * @bgap_status: BANDGAP_STATUS register offset
99 * @status_clean_stop_mask: mask to bandgap_status.clean_stop
100 * @status_bgap_alert_mask: mask to bandgap_status.bandgap_alert
101 * @status_hot_mask: mask to bandgap_status.hot
102 * @status_cold_mask: mask to bandgap_status.cold
103 * @bgap_cumul_dtemp: BANDGAP_CUMUL_DTEMP register offset
104 * @ctrl_dtemp_0: CTRL_DTEMP0 register offset
105 * @ctrl_dtemp_1: CTRL_DTEMP1 register offset
106 * @ctrl_dtemp_2: CTRL_DTEMP2 register offset
107 * @ctrl_dtemp_3: CTRL_DTEMP3 register offset
108 * @ctrl_dtemp_4: CTRL_DTEMP4 register offset
109 * @bgap_efuse: BANDGAP_EFUSE register offset
110 *
111 * The register offsets and bitfields might change across
112 * OMAP and variants versions. Hence this struct serves as a
113 * descriptor map on how to access the registers and the bitfields.
114 *
115 * This descriptor contains registers of all versions of bandgap chips.
116 * Not all versions will use all registers, depending on the available
117 * features. Please read TRMs for descriptive explanation on each bitfield.
118 */
119
120struct temp_sensor_registers {
121	u32	temp_sensor_ctrl;
122	u32	bgap_tempsoff_mask;
123	u32	bgap_soc_mask;
124	u32	bgap_eocz_mask; /* not used: but needs revisit */
125	u32	bgap_dtemp_mask;
126
127	u32	bgap_mask_ctrl;
128	u32	mask_hot_mask;
129	u32	mask_cold_mask;
130	u32	mask_sidlemode_mask; /* not used: but may be needed for pm */
131	u32	mask_counter_delay_mask;
132	u32	mask_freeze_mask;
133	u32	mask_clear_mask; /* not used: but needed for trending */
134	u32	mask_clear_accum_mask; /* not used: but needed for trending */
135
136	u32	bgap_mode_ctrl;
137	u32	mode_ctrl_mask;
138
139	u32	bgap_counter;
140	u32	counter_mask;
141
142	u32	bgap_threshold;
143	u32	threshold_thot_mask;
144	u32	threshold_tcold_mask;
145
146	u32	tshut_threshold;
147	u32	tshut_efuse_mask; /* not used */
148	u32	tshut_efuse_shift; /* not used */
149	u32	tshut_hot_mask;
150	u32	tshut_cold_mask;
151
152	u32	bgap_status;
153	u32	status_clean_stop_mask; /* not used: but needed for trending */
154	u32	status_bgap_alert_mask; /* not used */
155	u32	status_hot_mask;
156	u32	status_cold_mask;
157
158	u32	bgap_cumul_dtemp; /* not used: but needed for trending */
159	u32	ctrl_dtemp_0; /* not used: but needed for trending */
160	u32	ctrl_dtemp_1; /* not used: but needed for trending */
161	u32	ctrl_dtemp_2; /* not used: but needed for trending */
162	u32	ctrl_dtemp_3; /* not used: but needed for trending */
163	u32	ctrl_dtemp_4; /* not used: but needed for trending */
164	u32	bgap_efuse;
165};
166
167/**
168 * struct temp_sensor_data - The thresholds and limits for temperature sensors.
169 * @tshut_hot: temperature to trigger a thermal reset (initial value)
170 * @tshut_cold: temp to get the plat out of reset due to thermal (init val)
171 * @t_hot: temperature to trigger a thermal alert (high initial value)
172 * @t_cold: temperature to trigger a thermal alert (low initial value)
173 * @min_freq: sensor minimum clock rate
174 * @max_freq: sensor maximum clock rate
175 * @max_temp: sensor maximum temperature
176 * @min_temp: sensor minimum temperature
177 * @hyst_val: temperature hysteresis considered while converting ADC values
178 * @update_int1: update interval
179 * @update_int2: update interval
180 *
181 * This data structure will hold the required thresholds and temperature limits
182 * for a specific temperature sensor, like shutdown temperature, alert
183 * temperature, clock / rate used, ADC conversion limits and update intervals
184 */
185struct temp_sensor_data {
186	u32	tshut_hot;
187	u32	tshut_cold;
188	u32	t_hot;
189	u32	t_cold;
190	u32	min_freq;
191	u32	max_freq;
192	int     max_temp;
193	int     min_temp;
194	int     hyst_val;
195	u32     update_int1; /* not used */
196	u32     update_int2; /* not used */
197};
198
199struct ti_bandgap_data;
200
201/**
202 * struct temp_sensor_regval - temperature sensor register values and priv data
203 * @bg_mode_ctrl: temp sensor control register value
204 * @bg_ctrl: bandgap ctrl register value
205 * @bg_counter: bandgap counter value
206 * @bg_threshold: bandgap threshold register value
207 * @tshut_threshold: bandgap tshut register value
208 * @data: private data
209 *
210 * Data structure to save and restore bandgap register set context. Only
211 * required registers are shadowed, when needed.
212 */
213struct temp_sensor_regval {
214	u32			bg_mode_ctrl;
215	u32			bg_ctrl;
216	u32			bg_counter;
217	u32			bg_threshold;
218	u32			tshut_threshold;
219	void			*data;
220};
221
222/**
223 * struct ti_bandgap - bandgap device structure
224 * @dev: struct device pointer
225 * @base: io memory base address
226 * @conf: struct with bandgap configuration set (# sensors, conv_table, etc)
227 * @regval: temperature sensor register values
228 * @fclock: pointer to functional clock of temperature sensor
229 * @div_clk: pointer to divider clock of temperature sensor fclk
230 * @lock: spinlock for ti_bandgap structure
231 * @irq: MPU IRQ number for thermal alert
232 * @tshut_gpio: GPIO where Tshut signal is routed
233 * @clk_rate: Holds current clock rate
234 *
235 * The bandgap device structure representing the bandgap device instance.
236 * It holds most of the dynamic stuff. Configurations and sensor specific
237 * entries are inside the @conf structure.
238 */
239struct ti_bandgap {
240	struct device			*dev;
241	void __iomem			*base;
242	const struct ti_bandgap_data	*conf;
243	struct temp_sensor_regval	*regval;
244	struct clk			*fclock;
245	struct clk			*div_clk;
246	spinlock_t			lock; /* shields this struct */
247	int				irq;
248	int				tshut_gpio;
249	u32				clk_rate;
250};
251
252/**
253 * struct ti_temp_sensor - bandgap temperature sensor configuration data
254 * @ts_data: pointer to struct with thresholds, limits of temperature sensor
255 * @registers: pointer to the list of register offsets and bitfields
256 * @domain: the name of the domain where the sensor is located
257 * @slope: sensor gradient slope info for hotspot extrapolation equation
258 * @constant: sensor gradient const info for hotspot extrapolation equation
259 * @slope_pcb: sensor gradient slope info for hotspot extrapolation equation
260 *             with no external influence
261 * @constant_pcb: sensor gradient const info for hotspot extrapolation equation
262 *             with no external influence
263 * @register_cooling: function to describe how this sensor is going to be cooled
264 * @unregister_cooling: function to release cooling data
265 *
266 * Data structure to describe a temperature sensor handled by a bandgap device.
267 * It should provide configuration details on this sensor, such as how to
268 * access the registers affecting this sensor, shadow register buffer, how to
269 * assess the gradient from hotspot, how to cooldown the domain when sensor
270 * reports too hot temperature.
271 */
272struct ti_temp_sensor {
273	struct temp_sensor_data		*ts_data;
274	struct temp_sensor_registers	*registers;
275	char				*domain;
276	/* for hotspot extrapolation */
277	const int			slope;
278	const int			constant;
279	const int			slope_pcb;
280	const int			constant_pcb;
281	int (*register_cooling)(struct ti_bandgap *bgp, int id);
282	int (*unregister_cooling)(struct ti_bandgap *bgp, int id);
283};
284
285/**
286 * DOC: ti bandgap feature types
287 *
288 * TI_BANDGAP_FEATURE_TSHUT - used when the thermal shutdown signal output
289 *      of a bandgap device instance is routed to the processor. This means
290 *      the system must react and perform the shutdown by itself (handle an
291 *      IRQ, for instance).
292 *
293 * TI_BANDGAP_FEATURE_TSHUT_CONFIG - used when the bandgap device has control
294 *      over the thermal shutdown configuration. This means that the thermal
295 *      shutdown thresholds are programmable, for instance.
296 *
297 * TI_BANDGAP_FEATURE_TALERT - used when the bandgap device instance outputs
298 *      a signal representing violation of programmable alert thresholds.
299 *
300 * TI_BANDGAP_FEATURE_MODE_CONFIG - used when it is possible to choose which
301 *      mode, continuous or one shot, the bandgap device instance will operate.
302 *
303 * TI_BANDGAP_FEATURE_COUNTER - used when the bandgap device instance allows
304 *      programming the update interval of its internal state machine.
305 *
306 * TI_BANDGAP_FEATURE_POWER_SWITCH - used when the bandgap device allows
307 *      itself to be switched on/off.
308 *
309 * TI_BANDGAP_FEATURE_CLK_CTRL - used when the clocks feeding the bandgap
310 *      device are gateable or not.
311 *
312 * TI_BANDGAP_FEATURE_FREEZE_BIT - used when the bandgap device features
313 *      a history buffer that its update can be freezed/unfreezed.
314 *
315 * TI_BANDGAP_FEATURE_COUNTER_DELAY - used when the bandgap device features
316 *	a delay programming based on distinct values.
317 *
318 * TI_BANDGAP_FEATURE_HISTORY_BUFFER - used when the bandgap device features
319 *	a history buffer of temperatures.
320 *
321 * TI_BANDGAP_FEATURE_ERRATA_814 - used to workaorund when the bandgap device
322 *	has Errata 814
323 * TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device
324 *	has Errata 813
325 * TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a
326 *      specific feature (above) or not. Return non-zero, if yes.
327 */
328#define TI_BANDGAP_FEATURE_TSHUT		BIT(0)
329#define TI_BANDGAP_FEATURE_TSHUT_CONFIG		BIT(1)
330#define TI_BANDGAP_FEATURE_TALERT		BIT(2)
331#define TI_BANDGAP_FEATURE_MODE_CONFIG		BIT(3)
332#define TI_BANDGAP_FEATURE_COUNTER		BIT(4)
333#define TI_BANDGAP_FEATURE_POWER_SWITCH		BIT(5)
334#define TI_BANDGAP_FEATURE_CLK_CTRL		BIT(6)
335#define TI_BANDGAP_FEATURE_FREEZE_BIT		BIT(7)
336#define TI_BANDGAP_FEATURE_COUNTER_DELAY	BIT(8)
337#define TI_BANDGAP_FEATURE_HISTORY_BUFFER	BIT(9)
338#define TI_BANDGAP_FEATURE_ERRATA_814		BIT(10)
339#define TI_BANDGAP_FEATURE_ERRATA_813		BIT(11)
340#define TI_BANDGAP_HAS(b, f)			\
341			((b)->conf->features & TI_BANDGAP_FEATURE_ ## f)
342
343/**
344 * struct ti_bandgap_data - ti bandgap data configuration structure
345 * @features: a bitwise flag set to describe the device features
346 * @conv_table: Pointer to ADC to temperature conversion table
347 * @adc_start_val: ADC conversion table starting value
348 * @adc_end_val: ADC conversion table ending value
349 * @fclock_name: clock name of the functional clock
350 * @div_ck_name: clock name of the clock divisor
351 * @sensor_count: count of temperature sensor within this bandgap device
352 * @report_temperature: callback to report thermal alert to thermal API
353 * @expose_sensor: callback to export sensor to thermal API
354 * @remove_sensor: callback to destroy sensor from thermal API
355 * @sensors: array of sensors present in this bandgap instance
356 *
357 * This is a data structure which should hold most of the static configuration
358 * of a bandgap device instance. It should describe which features this instance
359 * is capable of, the clock names to feed this device, the amount of sensors and
360 * their configuration representation, and how to export and unexport them to
361 * a thermal API.
362 */
363struct ti_bandgap_data {
364	unsigned int			features;
365	const int			*conv_table;
366	u32				adc_start_val;
367	u32				adc_end_val;
368	char				*fclock_name;
369	char				*div_ck_name;
370	int				sensor_count;
371	int (*report_temperature)(struct ti_bandgap *bgp, int id);
372	int (*expose_sensor)(struct ti_bandgap *bgp, int id, char *domain);
373	int (*remove_sensor)(struct ti_bandgap *bgp, int id);
374
375	/* this needs to be at the end */
376	struct ti_temp_sensor		sensors[];
377};
378
379int ti_bandgap_read_thot(struct ti_bandgap *bgp, int id, int *thot);
380int ti_bandgap_write_thot(struct ti_bandgap *bgp, int id, int val);
381int ti_bandgap_read_tcold(struct ti_bandgap *bgp, int id, int *tcold);
382int ti_bandgap_write_tcold(struct ti_bandgap *bgp, int id, int val);
383int ti_bandgap_read_update_interval(struct ti_bandgap *bgp, int id,
384				    int *interval);
385int ti_bandgap_write_update_interval(struct ti_bandgap *bgp, int id,
386				     u32 interval);
387int ti_bandgap_read_temperature(struct ti_bandgap *bgp, int id,
388				  int *temperature);
389int ti_bandgap_set_sensor_data(struct ti_bandgap *bgp, int id, void *data);
390void *ti_bandgap_get_sensor_data(struct ti_bandgap *bgp, int id);
391int ti_bandgap_get_trend(struct ti_bandgap *bgp, int id, int *trend);
392
393#ifdef CONFIG_OMAP4_THERMAL
394extern const struct ti_bandgap_data omap4430_data;
395extern const struct ti_bandgap_data omap4460_data;
396extern const struct ti_bandgap_data omap4470_data;
397#else
398#define omap4430_data					NULL
399#define omap4460_data					NULL
400#define omap4470_data					NULL
401#endif
402
403#ifdef CONFIG_OMAP5_THERMAL
404extern const struct ti_bandgap_data omap5430_data;
405#else
406#define omap5430_data					NULL
407#endif
408
409#ifdef CONFIG_DRA752_THERMAL
410extern const struct ti_bandgap_data dra752_data;
411#else
412#define dra752_data					NULL
413#endif
414#endif
415