1/* 2 * A driver for the ARM PL022 PrimeCell SSP/SPI bus master. 3 * 4 * Copyright (C) 2008-2012 ST-Ericsson AB 5 * Copyright (C) 2006 STMicroelectronics Pvt. Ltd. 6 * 7 * Author: Linus Walleij <linus.walleij@stericsson.com> 8 * 9 * Initial version inspired by: 10 * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c 11 * Initial adoption to PL022 by: 12 * Sachin Verma <sachin.verma@st.com> 13 * 14 * This program is free software; you can redistribute it and/or modify 15 * it under the terms of the GNU General Public License as published by 16 * the Free Software Foundation; either version 2 of the License, or 17 * (at your option) any later version. 18 * 19 * This program is distributed in the hope that it will be useful, 20 * but WITHOUT ANY WARRANTY; without even the implied warranty of 21 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 22 * GNU General Public License for more details. 23 */ 24 25#include <linux/init.h> 26#include <linux/module.h> 27#include <linux/device.h> 28#include <linux/ioport.h> 29#include <linux/errno.h> 30#include <linux/interrupt.h> 31#include <linux/spi/spi.h> 32#include <linux/delay.h> 33#include <linux/clk.h> 34#include <linux/err.h> 35#include <linux/amba/bus.h> 36#include <linux/amba/pl022.h> 37#include <linux/io.h> 38#include <linux/slab.h> 39#include <linux/dmaengine.h> 40#include <linux/dma-mapping.h> 41#include <linux/scatterlist.h> 42#include <linux/pm_runtime.h> 43#include <linux/gpio.h> 44#include <linux/of_gpio.h> 45#include <linux/pinctrl/consumer.h> 46 47/* 48 * This macro is used to define some register default values. 49 * reg is masked with mask, the OR:ed with an (again masked) 50 * val shifted sb steps to the left. 51 */ 52#define SSP_WRITE_BITS(reg, val, mask, sb) \ 53 ((reg) = (((reg) & ~(mask)) | (((val)<<(sb)) & (mask)))) 54 55/* 56 * This macro is also used to define some default values. 57 * It will just shift val by sb steps to the left and mask 58 * the result with mask. 59 */ 60#define GEN_MASK_BITS(val, mask, sb) \ 61 (((val)<<(sb)) & (mask)) 62 63#define DRIVE_TX 0 64#define DO_NOT_DRIVE_TX 1 65 66#define DO_NOT_QUEUE_DMA 0 67#define QUEUE_DMA 1 68 69#define RX_TRANSFER 1 70#define TX_TRANSFER 2 71 72/* 73 * Macros to access SSP Registers with their offsets 74 */ 75#define SSP_CR0(r) (r + 0x000) 76#define SSP_CR1(r) (r + 0x004) 77#define SSP_DR(r) (r + 0x008) 78#define SSP_SR(r) (r + 0x00C) 79#define SSP_CPSR(r) (r + 0x010) 80#define SSP_IMSC(r) (r + 0x014) 81#define SSP_RIS(r) (r + 0x018) 82#define SSP_MIS(r) (r + 0x01C) 83#define SSP_ICR(r) (r + 0x020) 84#define SSP_DMACR(r) (r + 0x024) 85#define SSP_CSR(r) (r + 0x030) /* vendor extension */ 86#define SSP_ITCR(r) (r + 0x080) 87#define SSP_ITIP(r) (r + 0x084) 88#define SSP_ITOP(r) (r + 0x088) 89#define SSP_TDR(r) (r + 0x08C) 90 91#define SSP_PID0(r) (r + 0xFE0) 92#define SSP_PID1(r) (r + 0xFE4) 93#define SSP_PID2(r) (r + 0xFE8) 94#define SSP_PID3(r) (r + 0xFEC) 95 96#define SSP_CID0(r) (r + 0xFF0) 97#define SSP_CID1(r) (r + 0xFF4) 98#define SSP_CID2(r) (r + 0xFF8) 99#define SSP_CID3(r) (r + 0xFFC) 100 101/* 102 * SSP Control Register 0 - SSP_CR0 103 */ 104#define SSP_CR0_MASK_DSS (0x0FUL << 0) 105#define SSP_CR0_MASK_FRF (0x3UL << 4) 106#define SSP_CR0_MASK_SPO (0x1UL << 6) 107#define SSP_CR0_MASK_SPH (0x1UL << 7) 108#define SSP_CR0_MASK_SCR (0xFFUL << 8) 109 110/* 111 * The ST version of this block moves som bits 112 * in SSP_CR0 and extends it to 32 bits 113 */ 114#define SSP_CR0_MASK_DSS_ST (0x1FUL << 0) 115#define SSP_CR0_MASK_HALFDUP_ST (0x1UL << 5) 116#define SSP_CR0_MASK_CSS_ST (0x1FUL << 16) 117#define SSP_CR0_MASK_FRF_ST (0x3UL << 21) 118 119/* 120 * SSP Control Register 0 - SSP_CR1 121 */ 122#define SSP_CR1_MASK_LBM (0x1UL << 0) 123#define SSP_CR1_MASK_SSE (0x1UL << 1) 124#define SSP_CR1_MASK_MS (0x1UL << 2) 125#define SSP_CR1_MASK_SOD (0x1UL << 3) 126 127/* 128 * The ST version of this block adds some bits 129 * in SSP_CR1 130 */ 131#define SSP_CR1_MASK_RENDN_ST (0x1UL << 4) 132#define SSP_CR1_MASK_TENDN_ST (0x1UL << 5) 133#define SSP_CR1_MASK_MWAIT_ST (0x1UL << 6) 134#define SSP_CR1_MASK_RXIFLSEL_ST (0x7UL << 7) 135#define SSP_CR1_MASK_TXIFLSEL_ST (0x7UL << 10) 136/* This one is only in the PL023 variant */ 137#define SSP_CR1_MASK_FBCLKDEL_ST (0x7UL << 13) 138 139/* 140 * SSP Status Register - SSP_SR 141 */ 142#define SSP_SR_MASK_TFE (0x1UL << 0) /* Transmit FIFO empty */ 143#define SSP_SR_MASK_TNF (0x1UL << 1) /* Transmit FIFO not full */ 144#define SSP_SR_MASK_RNE (0x1UL << 2) /* Receive FIFO not empty */ 145#define SSP_SR_MASK_RFF (0x1UL << 3) /* Receive FIFO full */ 146#define SSP_SR_MASK_BSY (0x1UL << 4) /* Busy Flag */ 147 148/* 149 * SSP Clock Prescale Register - SSP_CPSR 150 */ 151#define SSP_CPSR_MASK_CPSDVSR (0xFFUL << 0) 152 153/* 154 * SSP Interrupt Mask Set/Clear Register - SSP_IMSC 155 */ 156#define SSP_IMSC_MASK_RORIM (0x1UL << 0) /* Receive Overrun Interrupt mask */ 157#define SSP_IMSC_MASK_RTIM (0x1UL << 1) /* Receive timeout Interrupt mask */ 158#define SSP_IMSC_MASK_RXIM (0x1UL << 2) /* Receive FIFO Interrupt mask */ 159#define SSP_IMSC_MASK_TXIM (0x1UL << 3) /* Transmit FIFO Interrupt mask */ 160 161/* 162 * SSP Raw Interrupt Status Register - SSP_RIS 163 */ 164/* Receive Overrun Raw Interrupt status */ 165#define SSP_RIS_MASK_RORRIS (0x1UL << 0) 166/* Receive Timeout Raw Interrupt status */ 167#define SSP_RIS_MASK_RTRIS (0x1UL << 1) 168/* Receive FIFO Raw Interrupt status */ 169#define SSP_RIS_MASK_RXRIS (0x1UL << 2) 170/* Transmit FIFO Raw Interrupt status */ 171#define SSP_RIS_MASK_TXRIS (0x1UL << 3) 172 173/* 174 * SSP Masked Interrupt Status Register - SSP_MIS 175 */ 176/* Receive Overrun Masked Interrupt status */ 177#define SSP_MIS_MASK_RORMIS (0x1UL << 0) 178/* Receive Timeout Masked Interrupt status */ 179#define SSP_MIS_MASK_RTMIS (0x1UL << 1) 180/* Receive FIFO Masked Interrupt status */ 181#define SSP_MIS_MASK_RXMIS (0x1UL << 2) 182/* Transmit FIFO Masked Interrupt status */ 183#define SSP_MIS_MASK_TXMIS (0x1UL << 3) 184 185/* 186 * SSP Interrupt Clear Register - SSP_ICR 187 */ 188/* Receive Overrun Raw Clear Interrupt bit */ 189#define SSP_ICR_MASK_RORIC (0x1UL << 0) 190/* Receive Timeout Clear Interrupt bit */ 191#define SSP_ICR_MASK_RTIC (0x1UL << 1) 192 193/* 194 * SSP DMA Control Register - SSP_DMACR 195 */ 196/* Receive DMA Enable bit */ 197#define SSP_DMACR_MASK_RXDMAE (0x1UL << 0) 198/* Transmit DMA Enable bit */ 199#define SSP_DMACR_MASK_TXDMAE (0x1UL << 1) 200 201/* 202 * SSP Chip Select Control Register - SSP_CSR 203 * (vendor extension) 204 */ 205#define SSP_CSR_CSVALUE_MASK (0x1FUL << 0) 206 207/* 208 * SSP Integration Test control Register - SSP_ITCR 209 */ 210#define SSP_ITCR_MASK_ITEN (0x1UL << 0) 211#define SSP_ITCR_MASK_TESTFIFO (0x1UL << 1) 212 213/* 214 * SSP Integration Test Input Register - SSP_ITIP 215 */ 216#define ITIP_MASK_SSPRXD (0x1UL << 0) 217#define ITIP_MASK_SSPFSSIN (0x1UL << 1) 218#define ITIP_MASK_SSPCLKIN (0x1UL << 2) 219#define ITIP_MASK_RXDMAC (0x1UL << 3) 220#define ITIP_MASK_TXDMAC (0x1UL << 4) 221#define ITIP_MASK_SSPTXDIN (0x1UL << 5) 222 223/* 224 * SSP Integration Test output Register - SSP_ITOP 225 */ 226#define ITOP_MASK_SSPTXD (0x1UL << 0) 227#define ITOP_MASK_SSPFSSOUT (0x1UL << 1) 228#define ITOP_MASK_SSPCLKOUT (0x1UL << 2) 229#define ITOP_MASK_SSPOEn (0x1UL << 3) 230#define ITOP_MASK_SSPCTLOEn (0x1UL << 4) 231#define ITOP_MASK_RORINTR (0x1UL << 5) 232#define ITOP_MASK_RTINTR (0x1UL << 6) 233#define ITOP_MASK_RXINTR (0x1UL << 7) 234#define ITOP_MASK_TXINTR (0x1UL << 8) 235#define ITOP_MASK_INTR (0x1UL << 9) 236#define ITOP_MASK_RXDMABREQ (0x1UL << 10) 237#define ITOP_MASK_RXDMASREQ (0x1UL << 11) 238#define ITOP_MASK_TXDMABREQ (0x1UL << 12) 239#define ITOP_MASK_TXDMASREQ (0x1UL << 13) 240 241/* 242 * SSP Test Data Register - SSP_TDR 243 */ 244#define TDR_MASK_TESTDATA (0xFFFFFFFF) 245 246/* 247 * Message State 248 * we use the spi_message.state (void *) pointer to 249 * hold a single state value, that's why all this 250 * (void *) casting is done here. 251 */ 252#define STATE_START ((void *) 0) 253#define STATE_RUNNING ((void *) 1) 254#define STATE_DONE ((void *) 2) 255#define STATE_ERROR ((void *) -1) 256 257/* 258 * SSP State - Whether Enabled or Disabled 259 */ 260#define SSP_DISABLED (0) 261#define SSP_ENABLED (1) 262 263/* 264 * SSP DMA State - Whether DMA Enabled or Disabled 265 */ 266#define SSP_DMA_DISABLED (0) 267#define SSP_DMA_ENABLED (1) 268 269/* 270 * SSP Clock Defaults 271 */ 272#define SSP_DEFAULT_CLKRATE 0x2 273#define SSP_DEFAULT_PRESCALE 0x40 274 275/* 276 * SSP Clock Parameter ranges 277 */ 278#define CPSDVR_MIN 0x02 279#define CPSDVR_MAX 0xFE 280#define SCR_MIN 0x00 281#define SCR_MAX 0xFF 282 283/* 284 * SSP Interrupt related Macros 285 */ 286#define DEFAULT_SSP_REG_IMSC 0x0UL 287#define DISABLE_ALL_INTERRUPTS DEFAULT_SSP_REG_IMSC 288#define ENABLE_ALL_INTERRUPTS ( \ 289 SSP_IMSC_MASK_RORIM | \ 290 SSP_IMSC_MASK_RTIM | \ 291 SSP_IMSC_MASK_RXIM | \ 292 SSP_IMSC_MASK_TXIM \ 293) 294 295#define CLEAR_ALL_INTERRUPTS 0x3 296 297#define SPI_POLLING_TIMEOUT 1000 298 299/* 300 * The type of reading going on on this chip 301 */ 302enum ssp_reading { 303 READING_NULL, 304 READING_U8, 305 READING_U16, 306 READING_U32 307}; 308 309/** 310 * The type of writing going on on this chip 311 */ 312enum ssp_writing { 313 WRITING_NULL, 314 WRITING_U8, 315 WRITING_U16, 316 WRITING_U32 317}; 318 319/** 320 * struct vendor_data - vendor-specific config parameters 321 * for PL022 derivates 322 * @fifodepth: depth of FIFOs (both) 323 * @max_bpw: maximum number of bits per word 324 * @unidir: supports unidirection transfers 325 * @extended_cr: 32 bit wide control register 0 with extra 326 * features and extra features in CR1 as found in the ST variants 327 * @pl023: supports a subset of the ST extensions called "PL023" 328 * @internal_cs_ctrl: supports chip select control register 329 */ 330struct vendor_data { 331 int fifodepth; 332 int max_bpw; 333 bool unidir; 334 bool extended_cr; 335 bool pl023; 336 bool loopback; 337 bool internal_cs_ctrl; 338}; 339 340/** 341 * struct pl022 - This is the private SSP driver data structure 342 * @adev: AMBA device model hookup 343 * @vendor: vendor data for the IP block 344 * @phybase: the physical memory where the SSP device resides 345 * @virtbase: the virtual memory where the SSP is mapped 346 * @clk: outgoing clock "SPICLK" for the SPI bus 347 * @master: SPI framework hookup 348 * @master_info: controller-specific data from machine setup 349 * @kworker: thread struct for message pump 350 * @kworker_task: pointer to task for message pump kworker thread 351 * @pump_messages: work struct for scheduling work to the message pump 352 * @queue_lock: spinlock to syncronise access to message queue 353 * @queue: message queue 354 * @busy: message pump is busy 355 * @running: message pump is running 356 * @pump_transfers: Tasklet used in Interrupt Transfer mode 357 * @cur_msg: Pointer to current spi_message being processed 358 * @cur_transfer: Pointer to current spi_transfer 359 * @cur_chip: pointer to current clients chip(assigned from controller_state) 360 * @next_msg_cs_active: the next message in the queue has been examined 361 * and it was found that it uses the same chip select as the previous 362 * message, so we left it active after the previous transfer, and it's 363 * active already. 364 * @tx: current position in TX buffer to be read 365 * @tx_end: end position in TX buffer to be read 366 * @rx: current position in RX buffer to be written 367 * @rx_end: end position in RX buffer to be written 368 * @read: the type of read currently going on 369 * @write: the type of write currently going on 370 * @exp_fifo_level: expected FIFO level 371 * @dma_rx_channel: optional channel for RX DMA 372 * @dma_tx_channel: optional channel for TX DMA 373 * @sgt_rx: scattertable for the RX transfer 374 * @sgt_tx: scattertable for the TX transfer 375 * @dummypage: a dummy page used for driving data on the bus with DMA 376 * @cur_cs: current chip select (gpio) 377 * @chipselects: list of chipselects (gpios) 378 */ 379struct pl022 { 380 struct amba_device *adev; 381 struct vendor_data *vendor; 382 resource_size_t phybase; 383 void __iomem *virtbase; 384 struct clk *clk; 385 struct spi_master *master; 386 struct pl022_ssp_controller *master_info; 387 /* Message per-transfer pump */ 388 struct tasklet_struct pump_transfers; 389 struct spi_message *cur_msg; 390 struct spi_transfer *cur_transfer; 391 struct chip_data *cur_chip; 392 bool next_msg_cs_active; 393 void *tx; 394 void *tx_end; 395 void *rx; 396 void *rx_end; 397 enum ssp_reading read; 398 enum ssp_writing write; 399 u32 exp_fifo_level; 400 enum ssp_rx_level_trig rx_lev_trig; 401 enum ssp_tx_level_trig tx_lev_trig; 402 /* DMA settings */ 403#ifdef CONFIG_DMA_ENGINE 404 struct dma_chan *dma_rx_channel; 405 struct dma_chan *dma_tx_channel; 406 struct sg_table sgt_rx; 407 struct sg_table sgt_tx; 408 char *dummypage; 409 bool dma_running; 410#endif 411 int cur_cs; 412 int *chipselects; 413}; 414 415/** 416 * struct chip_data - To maintain runtime state of SSP for each client chip 417 * @cr0: Value of control register CR0 of SSP - on later ST variants this 418 * register is 32 bits wide rather than just 16 419 * @cr1: Value of control register CR1 of SSP 420 * @dmacr: Value of DMA control Register of SSP 421 * @cpsr: Value of Clock prescale register 422 * @n_bytes: how many bytes(power of 2) reqd for a given data width of client 423 * @enable_dma: Whether to enable DMA or not 424 * @read: function ptr to be used to read when doing xfer for this chip 425 * @write: function ptr to be used to write when doing xfer for this chip 426 * @cs_control: chip select callback provided by chip 427 * @xfer_type: polling/interrupt/DMA 428 * 429 * Runtime state of the SSP controller, maintained per chip, 430 * This would be set according to the current message that would be served 431 */ 432struct chip_data { 433 u32 cr0; 434 u16 cr1; 435 u16 dmacr; 436 u16 cpsr; 437 u8 n_bytes; 438 bool enable_dma; 439 enum ssp_reading read; 440 enum ssp_writing write; 441 void (*cs_control) (u32 command); 442 int xfer_type; 443}; 444 445/** 446 * null_cs_control - Dummy chip select function 447 * @command: select/delect the chip 448 * 449 * If no chip select function is provided by client this is used as dummy 450 * chip select 451 */ 452static void null_cs_control(u32 command) 453{ 454 pr_debug("pl022: dummy chip select control, CS=0x%x\n", command); 455} 456 457/** 458 * internal_cs_control - Control chip select signals via SSP_CSR. 459 * @pl022: SSP driver private data structure 460 * @command: select/delect the chip 461 * 462 * Used on controller with internal chip select control via SSP_CSR register 463 * (vendor extension). Each of the 5 LSB in the register controls one chip 464 * select signal. 465 */ 466static void internal_cs_control(struct pl022 *pl022, u32 command) 467{ 468 u32 tmp; 469 470 tmp = readw(SSP_CSR(pl022->virtbase)); 471 if (command == SSP_CHIP_SELECT) 472 tmp &= ~BIT(pl022->cur_cs); 473 else 474 tmp |= BIT(pl022->cur_cs); 475 writew(tmp, SSP_CSR(pl022->virtbase)); 476} 477 478static void pl022_cs_control(struct pl022 *pl022, u32 command) 479{ 480 if (pl022->vendor->internal_cs_ctrl) 481 internal_cs_control(pl022, command); 482 else if (gpio_is_valid(pl022->cur_cs)) 483 gpio_set_value(pl022->cur_cs, command); 484 else 485 pl022->cur_chip->cs_control(command); 486} 487 488/** 489 * giveback - current spi_message is over, schedule next message and call 490 * callback of this message. Assumes that caller already 491 * set message->status; dma and pio irqs are blocked 492 * @pl022: SSP driver private data structure 493 */ 494static void giveback(struct pl022 *pl022) 495{ 496 struct spi_transfer *last_transfer; 497 pl022->next_msg_cs_active = false; 498 499 last_transfer = list_last_entry(&pl022->cur_msg->transfers, 500 struct spi_transfer, transfer_list); 501 502 /* Delay if requested before any change in chip select */ 503 if (last_transfer->delay_usecs) 504 /* 505 * FIXME: This runs in interrupt context. 506 * Is this really smart? 507 */ 508 udelay(last_transfer->delay_usecs); 509 510 if (!last_transfer->cs_change) { 511 struct spi_message *next_msg; 512 513 /* 514 * cs_change was not set. We can keep the chip select 515 * enabled if there is message in the queue and it is 516 * for the same spi device. 517 * 518 * We cannot postpone this until pump_messages, because 519 * after calling msg->complete (below) the driver that 520 * sent the current message could be unloaded, which 521 * could invalidate the cs_control() callback... 522 */ 523 /* get a pointer to the next message, if any */ 524 next_msg = spi_get_next_queued_message(pl022->master); 525 526 /* 527 * see if the next and current messages point 528 * to the same spi device. 529 */ 530 if (next_msg && next_msg->spi != pl022->cur_msg->spi) 531 next_msg = NULL; 532 if (!next_msg || pl022->cur_msg->state == STATE_ERROR) 533 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 534 else 535 pl022->next_msg_cs_active = true; 536 537 } 538 539 pl022->cur_msg = NULL; 540 pl022->cur_transfer = NULL; 541 pl022->cur_chip = NULL; 542 543 /* disable the SPI/SSP operation */ 544 writew((readw(SSP_CR1(pl022->virtbase)) & 545 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 546 547 spi_finalize_current_message(pl022->master); 548} 549 550/** 551 * flush - flush the FIFO to reach a clean state 552 * @pl022: SSP driver private data structure 553 */ 554static int flush(struct pl022 *pl022) 555{ 556 unsigned long limit = loops_per_jiffy << 1; 557 558 dev_dbg(&pl022->adev->dev, "flush\n"); 559 do { 560 while (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 561 readw(SSP_DR(pl022->virtbase)); 562 } while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_BSY) && limit--); 563 564 pl022->exp_fifo_level = 0; 565 566 return limit; 567} 568 569/** 570 * restore_state - Load configuration of current chip 571 * @pl022: SSP driver private data structure 572 */ 573static void restore_state(struct pl022 *pl022) 574{ 575 struct chip_data *chip = pl022->cur_chip; 576 577 if (pl022->vendor->extended_cr) 578 writel(chip->cr0, SSP_CR0(pl022->virtbase)); 579 else 580 writew(chip->cr0, SSP_CR0(pl022->virtbase)); 581 writew(chip->cr1, SSP_CR1(pl022->virtbase)); 582 writew(chip->dmacr, SSP_DMACR(pl022->virtbase)); 583 writew(chip->cpsr, SSP_CPSR(pl022->virtbase)); 584 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 585 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 586} 587 588/* 589 * Default SSP Register Values 590 */ 591#define DEFAULT_SSP_REG_CR0 ( \ 592 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS, 0) | \ 593 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF, 4) | \ 594 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 595 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 596 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 597) 598 599/* ST versions have slightly different bit layout */ 600#define DEFAULT_SSP_REG_CR0_ST ( \ 601 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 602 GEN_MASK_BITS(SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, SSP_CR0_MASK_HALFDUP_ST, 5) | \ 603 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 604 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 605 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) | \ 606 GEN_MASK_BITS(SSP_BITS_8, SSP_CR0_MASK_CSS_ST, 16) | \ 607 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF_ST, 21) \ 608) 609 610/* The PL023 version is slightly different again */ 611#define DEFAULT_SSP_REG_CR0_ST_PL023 ( \ 612 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 613 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 614 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 615 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 616) 617 618#define DEFAULT_SSP_REG_CR1 ( \ 619 GEN_MASK_BITS(LOOPBACK_DISABLED, SSP_CR1_MASK_LBM, 0) | \ 620 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 621 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 622 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) \ 623) 624 625/* ST versions extend this register to use all 16 bits */ 626#define DEFAULT_SSP_REG_CR1_ST ( \ 627 DEFAULT_SSP_REG_CR1 | \ 628 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 629 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 630 GEN_MASK_BITS(SSP_MWIRE_WAIT_ZERO, SSP_CR1_MASK_MWAIT_ST, 6) |\ 631 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 632 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) \ 633) 634 635/* 636 * The PL023 variant has further differences: no loopback mode, no microwire 637 * support, and a new clock feedback delay setting. 638 */ 639#define DEFAULT_SSP_REG_CR1_ST_PL023 ( \ 640 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 641 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 642 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) | \ 643 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 644 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 645 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 646 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) | \ 647 GEN_MASK_BITS(SSP_FEEDBACK_CLK_DELAY_NONE, SSP_CR1_MASK_FBCLKDEL_ST, 13) \ 648) 649 650#define DEFAULT_SSP_REG_CPSR ( \ 651 GEN_MASK_BITS(SSP_DEFAULT_PRESCALE, SSP_CPSR_MASK_CPSDVSR, 0) \ 652) 653 654#define DEFAULT_SSP_REG_DMACR (\ 655 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_RXDMAE, 0) | \ 656 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_TXDMAE, 1) \ 657) 658 659/** 660 * load_ssp_default_config - Load default configuration for SSP 661 * @pl022: SSP driver private data structure 662 */ 663static void load_ssp_default_config(struct pl022 *pl022) 664{ 665 if (pl022->vendor->pl023) { 666 writel(DEFAULT_SSP_REG_CR0_ST_PL023, SSP_CR0(pl022->virtbase)); 667 writew(DEFAULT_SSP_REG_CR1_ST_PL023, SSP_CR1(pl022->virtbase)); 668 } else if (pl022->vendor->extended_cr) { 669 writel(DEFAULT_SSP_REG_CR0_ST, SSP_CR0(pl022->virtbase)); 670 writew(DEFAULT_SSP_REG_CR1_ST, SSP_CR1(pl022->virtbase)); 671 } else { 672 writew(DEFAULT_SSP_REG_CR0, SSP_CR0(pl022->virtbase)); 673 writew(DEFAULT_SSP_REG_CR1, SSP_CR1(pl022->virtbase)); 674 } 675 writew(DEFAULT_SSP_REG_DMACR, SSP_DMACR(pl022->virtbase)); 676 writew(DEFAULT_SSP_REG_CPSR, SSP_CPSR(pl022->virtbase)); 677 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 678 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 679} 680 681/** 682 * This will write to TX and read from RX according to the parameters 683 * set in pl022. 684 */ 685static void readwriter(struct pl022 *pl022) 686{ 687 688 /* 689 * The FIFO depth is different between primecell variants. 690 * I believe filling in too much in the FIFO might cause 691 * errons in 8bit wide transfers on ARM variants (just 8 words 692 * FIFO, means only 8x8 = 64 bits in FIFO) at least. 693 * 694 * To prevent this issue, the TX FIFO is only filled to the 695 * unused RX FIFO fill length, regardless of what the TX 696 * FIFO status flag indicates. 697 */ 698 dev_dbg(&pl022->adev->dev, 699 "%s, rx: %p, rxend: %p, tx: %p, txend: %p\n", 700 __func__, pl022->rx, pl022->rx_end, pl022->tx, pl022->tx_end); 701 702 /* Read as much as you can */ 703 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 704 && (pl022->rx < pl022->rx_end)) { 705 switch (pl022->read) { 706 case READING_NULL: 707 readw(SSP_DR(pl022->virtbase)); 708 break; 709 case READING_U8: 710 *(u8 *) (pl022->rx) = 711 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 712 break; 713 case READING_U16: 714 *(u16 *) (pl022->rx) = 715 (u16) readw(SSP_DR(pl022->virtbase)); 716 break; 717 case READING_U32: 718 *(u32 *) (pl022->rx) = 719 readl(SSP_DR(pl022->virtbase)); 720 break; 721 } 722 pl022->rx += (pl022->cur_chip->n_bytes); 723 pl022->exp_fifo_level--; 724 } 725 /* 726 * Write as much as possible up to the RX FIFO size 727 */ 728 while ((pl022->exp_fifo_level < pl022->vendor->fifodepth) 729 && (pl022->tx < pl022->tx_end)) { 730 switch (pl022->write) { 731 case WRITING_NULL: 732 writew(0x0, SSP_DR(pl022->virtbase)); 733 break; 734 case WRITING_U8: 735 writew(*(u8 *) (pl022->tx), SSP_DR(pl022->virtbase)); 736 break; 737 case WRITING_U16: 738 writew((*(u16 *) (pl022->tx)), SSP_DR(pl022->virtbase)); 739 break; 740 case WRITING_U32: 741 writel(*(u32 *) (pl022->tx), SSP_DR(pl022->virtbase)); 742 break; 743 } 744 pl022->tx += (pl022->cur_chip->n_bytes); 745 pl022->exp_fifo_level++; 746 /* 747 * This inner reader takes care of things appearing in the RX 748 * FIFO as we're transmitting. This will happen a lot since the 749 * clock starts running when you put things into the TX FIFO, 750 * and then things are continuously clocked into the RX FIFO. 751 */ 752 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 753 && (pl022->rx < pl022->rx_end)) { 754 switch (pl022->read) { 755 case READING_NULL: 756 readw(SSP_DR(pl022->virtbase)); 757 break; 758 case READING_U8: 759 *(u8 *) (pl022->rx) = 760 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 761 break; 762 case READING_U16: 763 *(u16 *) (pl022->rx) = 764 (u16) readw(SSP_DR(pl022->virtbase)); 765 break; 766 case READING_U32: 767 *(u32 *) (pl022->rx) = 768 readl(SSP_DR(pl022->virtbase)); 769 break; 770 } 771 pl022->rx += (pl022->cur_chip->n_bytes); 772 pl022->exp_fifo_level--; 773 } 774 } 775 /* 776 * When we exit here the TX FIFO should be full and the RX FIFO 777 * should be empty 778 */ 779} 780 781/** 782 * next_transfer - Move to the Next transfer in the current spi message 783 * @pl022: SSP driver private data structure 784 * 785 * This function moves though the linked list of spi transfers in the 786 * current spi message and returns with the state of current spi 787 * message i.e whether its last transfer is done(STATE_DONE) or 788 * Next transfer is ready(STATE_RUNNING) 789 */ 790static void *next_transfer(struct pl022 *pl022) 791{ 792 struct spi_message *msg = pl022->cur_msg; 793 struct spi_transfer *trans = pl022->cur_transfer; 794 795 /* Move to next transfer */ 796 if (trans->transfer_list.next != &msg->transfers) { 797 pl022->cur_transfer = 798 list_entry(trans->transfer_list.next, 799 struct spi_transfer, transfer_list); 800 return STATE_RUNNING; 801 } 802 return STATE_DONE; 803} 804 805/* 806 * This DMA functionality is only compiled in if we have 807 * access to the generic DMA devices/DMA engine. 808 */ 809#ifdef CONFIG_DMA_ENGINE 810static void unmap_free_dma_scatter(struct pl022 *pl022) 811{ 812 /* Unmap and free the SG tables */ 813 dma_unmap_sg(pl022->dma_tx_channel->device->dev, pl022->sgt_tx.sgl, 814 pl022->sgt_tx.nents, DMA_TO_DEVICE); 815 dma_unmap_sg(pl022->dma_rx_channel->device->dev, pl022->sgt_rx.sgl, 816 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 817 sg_free_table(&pl022->sgt_rx); 818 sg_free_table(&pl022->sgt_tx); 819} 820 821static void dma_callback(void *data) 822{ 823 struct pl022 *pl022 = data; 824 struct spi_message *msg = pl022->cur_msg; 825 826 BUG_ON(!pl022->sgt_rx.sgl); 827 828#ifdef VERBOSE_DEBUG 829 /* 830 * Optionally dump out buffers to inspect contents, this is 831 * good if you want to convince yourself that the loopback 832 * read/write contents are the same, when adopting to a new 833 * DMA engine. 834 */ 835 { 836 struct scatterlist *sg; 837 unsigned int i; 838 839 dma_sync_sg_for_cpu(&pl022->adev->dev, 840 pl022->sgt_rx.sgl, 841 pl022->sgt_rx.nents, 842 DMA_FROM_DEVICE); 843 844 for_each_sg(pl022->sgt_rx.sgl, sg, pl022->sgt_rx.nents, i) { 845 dev_dbg(&pl022->adev->dev, "SPI RX SG ENTRY: %d", i); 846 print_hex_dump(KERN_ERR, "SPI RX: ", 847 DUMP_PREFIX_OFFSET, 848 16, 849 1, 850 sg_virt(sg), 851 sg_dma_len(sg), 852 1); 853 } 854 for_each_sg(pl022->sgt_tx.sgl, sg, pl022->sgt_tx.nents, i) { 855 dev_dbg(&pl022->adev->dev, "SPI TX SG ENTRY: %d", i); 856 print_hex_dump(KERN_ERR, "SPI TX: ", 857 DUMP_PREFIX_OFFSET, 858 16, 859 1, 860 sg_virt(sg), 861 sg_dma_len(sg), 862 1); 863 } 864 } 865#endif 866 867 unmap_free_dma_scatter(pl022); 868 869 /* Update total bytes transferred */ 870 msg->actual_length += pl022->cur_transfer->len; 871 if (pl022->cur_transfer->cs_change) 872 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 873 874 /* Move to next transfer */ 875 msg->state = next_transfer(pl022); 876 tasklet_schedule(&pl022->pump_transfers); 877} 878 879static void setup_dma_scatter(struct pl022 *pl022, 880 void *buffer, 881 unsigned int length, 882 struct sg_table *sgtab) 883{ 884 struct scatterlist *sg; 885 int bytesleft = length; 886 void *bufp = buffer; 887 int mapbytes; 888 int i; 889 890 if (buffer) { 891 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 892 /* 893 * If there are less bytes left than what fits 894 * in the current page (plus page alignment offset) 895 * we just feed in this, else we stuff in as much 896 * as we can. 897 */ 898 if (bytesleft < (PAGE_SIZE - offset_in_page(bufp))) 899 mapbytes = bytesleft; 900 else 901 mapbytes = PAGE_SIZE - offset_in_page(bufp); 902 sg_set_page(sg, virt_to_page(bufp), 903 mapbytes, offset_in_page(bufp)); 904 bufp += mapbytes; 905 bytesleft -= mapbytes; 906 dev_dbg(&pl022->adev->dev, 907 "set RX/TX target page @ %p, %d bytes, %d left\n", 908 bufp, mapbytes, bytesleft); 909 } 910 } else { 911 /* Map the dummy buffer on every page */ 912 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 913 if (bytesleft < PAGE_SIZE) 914 mapbytes = bytesleft; 915 else 916 mapbytes = PAGE_SIZE; 917 sg_set_page(sg, virt_to_page(pl022->dummypage), 918 mapbytes, 0); 919 bytesleft -= mapbytes; 920 dev_dbg(&pl022->adev->dev, 921 "set RX/TX to dummy page %d bytes, %d left\n", 922 mapbytes, bytesleft); 923 924 } 925 } 926 BUG_ON(bytesleft); 927} 928 929/** 930 * configure_dma - configures the channels for the next transfer 931 * @pl022: SSP driver's private data structure 932 */ 933static int configure_dma(struct pl022 *pl022) 934{ 935 struct dma_slave_config rx_conf = { 936 .src_addr = SSP_DR(pl022->phybase), 937 .direction = DMA_DEV_TO_MEM, 938 .device_fc = false, 939 }; 940 struct dma_slave_config tx_conf = { 941 .dst_addr = SSP_DR(pl022->phybase), 942 .direction = DMA_MEM_TO_DEV, 943 .device_fc = false, 944 }; 945 unsigned int pages; 946 int ret; 947 int rx_sglen, tx_sglen; 948 struct dma_chan *rxchan = pl022->dma_rx_channel; 949 struct dma_chan *txchan = pl022->dma_tx_channel; 950 struct dma_async_tx_descriptor *rxdesc; 951 struct dma_async_tx_descriptor *txdesc; 952 953 /* Check that the channels are available */ 954 if (!rxchan || !txchan) 955 return -ENODEV; 956 957 /* 958 * If supplied, the DMA burstsize should equal the FIFO trigger level. 959 * Notice that the DMA engine uses one-to-one mapping. Since we can 960 * not trigger on 2 elements this needs explicit mapping rather than 961 * calculation. 962 */ 963 switch (pl022->rx_lev_trig) { 964 case SSP_RX_1_OR_MORE_ELEM: 965 rx_conf.src_maxburst = 1; 966 break; 967 case SSP_RX_4_OR_MORE_ELEM: 968 rx_conf.src_maxburst = 4; 969 break; 970 case SSP_RX_8_OR_MORE_ELEM: 971 rx_conf.src_maxburst = 8; 972 break; 973 case SSP_RX_16_OR_MORE_ELEM: 974 rx_conf.src_maxburst = 16; 975 break; 976 case SSP_RX_32_OR_MORE_ELEM: 977 rx_conf.src_maxburst = 32; 978 break; 979 default: 980 rx_conf.src_maxburst = pl022->vendor->fifodepth >> 1; 981 break; 982 } 983 984 switch (pl022->tx_lev_trig) { 985 case SSP_TX_1_OR_MORE_EMPTY_LOC: 986 tx_conf.dst_maxburst = 1; 987 break; 988 case SSP_TX_4_OR_MORE_EMPTY_LOC: 989 tx_conf.dst_maxburst = 4; 990 break; 991 case SSP_TX_8_OR_MORE_EMPTY_LOC: 992 tx_conf.dst_maxburst = 8; 993 break; 994 case SSP_TX_16_OR_MORE_EMPTY_LOC: 995 tx_conf.dst_maxburst = 16; 996 break; 997 case SSP_TX_32_OR_MORE_EMPTY_LOC: 998 tx_conf.dst_maxburst = 32; 999 break; 1000 default: 1001 tx_conf.dst_maxburst = pl022->vendor->fifodepth >> 1; 1002 break; 1003 } 1004 1005 switch (pl022->read) { 1006 case READING_NULL: 1007 /* Use the same as for writing */ 1008 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1009 break; 1010 case READING_U8: 1011 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1012 break; 1013 case READING_U16: 1014 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1015 break; 1016 case READING_U32: 1017 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1018 break; 1019 } 1020 1021 switch (pl022->write) { 1022 case WRITING_NULL: 1023 /* Use the same as for reading */ 1024 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1025 break; 1026 case WRITING_U8: 1027 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1028 break; 1029 case WRITING_U16: 1030 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1031 break; 1032 case WRITING_U32: 1033 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1034 break; 1035 } 1036 1037 /* SPI pecularity: we need to read and write the same width */ 1038 if (rx_conf.src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1039 rx_conf.src_addr_width = tx_conf.dst_addr_width; 1040 if (tx_conf.dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1041 tx_conf.dst_addr_width = rx_conf.src_addr_width; 1042 BUG_ON(rx_conf.src_addr_width != tx_conf.dst_addr_width); 1043 1044 dmaengine_slave_config(rxchan, &rx_conf); 1045 dmaengine_slave_config(txchan, &tx_conf); 1046 1047 /* Create sglists for the transfers */ 1048 pages = DIV_ROUND_UP(pl022->cur_transfer->len, PAGE_SIZE); 1049 dev_dbg(&pl022->adev->dev, "using %d pages for transfer\n", pages); 1050 1051 ret = sg_alloc_table(&pl022->sgt_rx, pages, GFP_ATOMIC); 1052 if (ret) 1053 goto err_alloc_rx_sg; 1054 1055 ret = sg_alloc_table(&pl022->sgt_tx, pages, GFP_ATOMIC); 1056 if (ret) 1057 goto err_alloc_tx_sg; 1058 1059 /* Fill in the scatterlists for the RX+TX buffers */ 1060 setup_dma_scatter(pl022, pl022->rx, 1061 pl022->cur_transfer->len, &pl022->sgt_rx); 1062 setup_dma_scatter(pl022, pl022->tx, 1063 pl022->cur_transfer->len, &pl022->sgt_tx); 1064 1065 /* Map DMA buffers */ 1066 rx_sglen = dma_map_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1067 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1068 if (!rx_sglen) 1069 goto err_rx_sgmap; 1070 1071 tx_sglen = dma_map_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1072 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1073 if (!tx_sglen) 1074 goto err_tx_sgmap; 1075 1076 /* Send both scatterlists */ 1077 rxdesc = dmaengine_prep_slave_sg(rxchan, 1078 pl022->sgt_rx.sgl, 1079 rx_sglen, 1080 DMA_DEV_TO_MEM, 1081 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1082 if (!rxdesc) 1083 goto err_rxdesc; 1084 1085 txdesc = dmaengine_prep_slave_sg(txchan, 1086 pl022->sgt_tx.sgl, 1087 tx_sglen, 1088 DMA_MEM_TO_DEV, 1089 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1090 if (!txdesc) 1091 goto err_txdesc; 1092 1093 /* Put the callback on the RX transfer only, that should finish last */ 1094 rxdesc->callback = dma_callback; 1095 rxdesc->callback_param = pl022; 1096 1097 /* Submit and fire RX and TX with TX last so we're ready to read! */ 1098 dmaengine_submit(rxdesc); 1099 dmaengine_submit(txdesc); 1100 dma_async_issue_pending(rxchan); 1101 dma_async_issue_pending(txchan); 1102 pl022->dma_running = true; 1103 1104 return 0; 1105 1106err_txdesc: 1107 dmaengine_terminate_all(txchan); 1108err_rxdesc: 1109 dmaengine_terminate_all(rxchan); 1110 dma_unmap_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1111 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1112err_tx_sgmap: 1113 dma_unmap_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1114 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1115err_rx_sgmap: 1116 sg_free_table(&pl022->sgt_tx); 1117err_alloc_tx_sg: 1118 sg_free_table(&pl022->sgt_rx); 1119err_alloc_rx_sg: 1120 return -ENOMEM; 1121} 1122 1123static int pl022_dma_probe(struct pl022 *pl022) 1124{ 1125 dma_cap_mask_t mask; 1126 1127 /* Try to acquire a generic DMA engine slave channel */ 1128 dma_cap_zero(mask); 1129 dma_cap_set(DMA_SLAVE, mask); 1130 /* 1131 * We need both RX and TX channels to do DMA, else do none 1132 * of them. 1133 */ 1134 pl022->dma_rx_channel = dma_request_channel(mask, 1135 pl022->master_info->dma_filter, 1136 pl022->master_info->dma_rx_param); 1137 if (!pl022->dma_rx_channel) { 1138 dev_dbg(&pl022->adev->dev, "no RX DMA channel!\n"); 1139 goto err_no_rxchan; 1140 } 1141 1142 pl022->dma_tx_channel = dma_request_channel(mask, 1143 pl022->master_info->dma_filter, 1144 pl022->master_info->dma_tx_param); 1145 if (!pl022->dma_tx_channel) { 1146 dev_dbg(&pl022->adev->dev, "no TX DMA channel!\n"); 1147 goto err_no_txchan; 1148 } 1149 1150 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1151 if (!pl022->dummypage) 1152 goto err_no_dummypage; 1153 1154 dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n", 1155 dma_chan_name(pl022->dma_rx_channel), 1156 dma_chan_name(pl022->dma_tx_channel)); 1157 1158 return 0; 1159 1160err_no_dummypage: 1161 dma_release_channel(pl022->dma_tx_channel); 1162err_no_txchan: 1163 dma_release_channel(pl022->dma_rx_channel); 1164 pl022->dma_rx_channel = NULL; 1165err_no_rxchan: 1166 dev_err(&pl022->adev->dev, 1167 "Failed to work in dma mode, work without dma!\n"); 1168 return -ENODEV; 1169} 1170 1171static int pl022_dma_autoprobe(struct pl022 *pl022) 1172{ 1173 struct device *dev = &pl022->adev->dev; 1174 1175 /* automatically configure DMA channels from platform, normally using DT */ 1176 pl022->dma_rx_channel = dma_request_slave_channel(dev, "rx"); 1177 if (!pl022->dma_rx_channel) 1178 goto err_no_rxchan; 1179 1180 pl022->dma_tx_channel = dma_request_slave_channel(dev, "tx"); 1181 if (!pl022->dma_tx_channel) 1182 goto err_no_txchan; 1183 1184 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1185 if (!pl022->dummypage) 1186 goto err_no_dummypage; 1187 1188 return 0; 1189 1190err_no_dummypage: 1191 dma_release_channel(pl022->dma_tx_channel); 1192 pl022->dma_tx_channel = NULL; 1193err_no_txchan: 1194 dma_release_channel(pl022->dma_rx_channel); 1195 pl022->dma_rx_channel = NULL; 1196err_no_rxchan: 1197 return -ENODEV; 1198} 1199 1200static void terminate_dma(struct pl022 *pl022) 1201{ 1202 struct dma_chan *rxchan = pl022->dma_rx_channel; 1203 struct dma_chan *txchan = pl022->dma_tx_channel; 1204 1205 dmaengine_terminate_all(rxchan); 1206 dmaengine_terminate_all(txchan); 1207 unmap_free_dma_scatter(pl022); 1208 pl022->dma_running = false; 1209} 1210 1211static void pl022_dma_remove(struct pl022 *pl022) 1212{ 1213 if (pl022->dma_running) 1214 terminate_dma(pl022); 1215 if (pl022->dma_tx_channel) 1216 dma_release_channel(pl022->dma_tx_channel); 1217 if (pl022->dma_rx_channel) 1218 dma_release_channel(pl022->dma_rx_channel); 1219 kfree(pl022->dummypage); 1220} 1221 1222#else 1223static inline int configure_dma(struct pl022 *pl022) 1224{ 1225 return -ENODEV; 1226} 1227 1228static inline int pl022_dma_autoprobe(struct pl022 *pl022) 1229{ 1230 return 0; 1231} 1232 1233static inline int pl022_dma_probe(struct pl022 *pl022) 1234{ 1235 return 0; 1236} 1237 1238static inline void pl022_dma_remove(struct pl022 *pl022) 1239{ 1240} 1241#endif 1242 1243/** 1244 * pl022_interrupt_handler - Interrupt handler for SSP controller 1245 * 1246 * This function handles interrupts generated for an interrupt based transfer. 1247 * If a receive overrun (ROR) interrupt is there then we disable SSP, flag the 1248 * current message's state as STATE_ERROR and schedule the tasklet 1249 * pump_transfers which will do the postprocessing of the current message by 1250 * calling giveback(). Otherwise it reads data from RX FIFO till there is no 1251 * more data, and writes data in TX FIFO till it is not full. If we complete 1252 * the transfer we move to the next transfer and schedule the tasklet. 1253 */ 1254static irqreturn_t pl022_interrupt_handler(int irq, void *dev_id) 1255{ 1256 struct pl022 *pl022 = dev_id; 1257 struct spi_message *msg = pl022->cur_msg; 1258 u16 irq_status = 0; 1259 1260 if (unlikely(!msg)) { 1261 dev_err(&pl022->adev->dev, 1262 "bad message state in interrupt handler"); 1263 /* Never fail */ 1264 return IRQ_HANDLED; 1265 } 1266 1267 /* Read the Interrupt Status Register */ 1268 irq_status = readw(SSP_MIS(pl022->virtbase)); 1269 1270 if (unlikely(!irq_status)) 1271 return IRQ_NONE; 1272 1273 /* 1274 * This handles the FIFO interrupts, the timeout 1275 * interrupts are flatly ignored, they cannot be 1276 * trusted. 1277 */ 1278 if (unlikely(irq_status & SSP_MIS_MASK_RORMIS)) { 1279 /* 1280 * Overrun interrupt - bail out since our Data has been 1281 * corrupted 1282 */ 1283 dev_err(&pl022->adev->dev, "FIFO overrun\n"); 1284 if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RFF) 1285 dev_err(&pl022->adev->dev, 1286 "RXFIFO is full\n"); 1287 1288 /* 1289 * Disable and clear interrupts, disable SSP, 1290 * mark message with bad status so it can be 1291 * retried. 1292 */ 1293 writew(DISABLE_ALL_INTERRUPTS, 1294 SSP_IMSC(pl022->virtbase)); 1295 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1296 writew((readw(SSP_CR1(pl022->virtbase)) & 1297 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1298 msg->state = STATE_ERROR; 1299 1300 /* Schedule message queue handler */ 1301 tasklet_schedule(&pl022->pump_transfers); 1302 return IRQ_HANDLED; 1303 } 1304 1305 readwriter(pl022); 1306 1307 if (pl022->tx == pl022->tx_end) { 1308 /* Disable Transmit interrupt, enable receive interrupt */ 1309 writew((readw(SSP_IMSC(pl022->virtbase)) & 1310 ~SSP_IMSC_MASK_TXIM) | SSP_IMSC_MASK_RXIM, 1311 SSP_IMSC(pl022->virtbase)); 1312 } 1313 1314 /* 1315 * Since all transactions must write as much as shall be read, 1316 * we can conclude the entire transaction once RX is complete. 1317 * At this point, all TX will always be finished. 1318 */ 1319 if (pl022->rx >= pl022->rx_end) { 1320 writew(DISABLE_ALL_INTERRUPTS, 1321 SSP_IMSC(pl022->virtbase)); 1322 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1323 if (unlikely(pl022->rx > pl022->rx_end)) { 1324 dev_warn(&pl022->adev->dev, "read %u surplus " 1325 "bytes (did you request an odd " 1326 "number of bytes on a 16bit bus?)\n", 1327 (u32) (pl022->rx - pl022->rx_end)); 1328 } 1329 /* Update total bytes transferred */ 1330 msg->actual_length += pl022->cur_transfer->len; 1331 if (pl022->cur_transfer->cs_change) 1332 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1333 /* Move to next transfer */ 1334 msg->state = next_transfer(pl022); 1335 tasklet_schedule(&pl022->pump_transfers); 1336 return IRQ_HANDLED; 1337 } 1338 1339 return IRQ_HANDLED; 1340} 1341 1342/** 1343 * This sets up the pointers to memory for the next message to 1344 * send out on the SPI bus. 1345 */ 1346static int set_up_next_transfer(struct pl022 *pl022, 1347 struct spi_transfer *transfer) 1348{ 1349 int residue; 1350 1351 /* Sanity check the message for this bus width */ 1352 residue = pl022->cur_transfer->len % pl022->cur_chip->n_bytes; 1353 if (unlikely(residue != 0)) { 1354 dev_err(&pl022->adev->dev, 1355 "message of %u bytes to transmit but the current " 1356 "chip bus has a data width of %u bytes!\n", 1357 pl022->cur_transfer->len, 1358 pl022->cur_chip->n_bytes); 1359 dev_err(&pl022->adev->dev, "skipping this message\n"); 1360 return -EIO; 1361 } 1362 pl022->tx = (void *)transfer->tx_buf; 1363 pl022->tx_end = pl022->tx + pl022->cur_transfer->len; 1364 pl022->rx = (void *)transfer->rx_buf; 1365 pl022->rx_end = pl022->rx + pl022->cur_transfer->len; 1366 pl022->write = 1367 pl022->tx ? pl022->cur_chip->write : WRITING_NULL; 1368 pl022->read = pl022->rx ? pl022->cur_chip->read : READING_NULL; 1369 return 0; 1370} 1371 1372/** 1373 * pump_transfers - Tasklet function which schedules next transfer 1374 * when running in interrupt or DMA transfer mode. 1375 * @data: SSP driver private data structure 1376 * 1377 */ 1378static void pump_transfers(unsigned long data) 1379{ 1380 struct pl022 *pl022 = (struct pl022 *) data; 1381 struct spi_message *message = NULL; 1382 struct spi_transfer *transfer = NULL; 1383 struct spi_transfer *previous = NULL; 1384 1385 /* Get current state information */ 1386 message = pl022->cur_msg; 1387 transfer = pl022->cur_transfer; 1388 1389 /* Handle for abort */ 1390 if (message->state == STATE_ERROR) { 1391 message->status = -EIO; 1392 giveback(pl022); 1393 return; 1394 } 1395 1396 /* Handle end of message */ 1397 if (message->state == STATE_DONE) { 1398 message->status = 0; 1399 giveback(pl022); 1400 return; 1401 } 1402 1403 /* Delay if requested at end of transfer before CS change */ 1404 if (message->state == STATE_RUNNING) { 1405 previous = list_entry(transfer->transfer_list.prev, 1406 struct spi_transfer, 1407 transfer_list); 1408 if (previous->delay_usecs) 1409 /* 1410 * FIXME: This runs in interrupt context. 1411 * Is this really smart? 1412 */ 1413 udelay(previous->delay_usecs); 1414 1415 /* Reselect chip select only if cs_change was requested */ 1416 if (previous->cs_change) 1417 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1418 } else { 1419 /* STATE_START */ 1420 message->state = STATE_RUNNING; 1421 } 1422 1423 if (set_up_next_transfer(pl022, transfer)) { 1424 message->state = STATE_ERROR; 1425 message->status = -EIO; 1426 giveback(pl022); 1427 return; 1428 } 1429 /* Flush the FIFOs and let's go! */ 1430 flush(pl022); 1431 1432 if (pl022->cur_chip->enable_dma) { 1433 if (configure_dma(pl022)) { 1434 dev_dbg(&pl022->adev->dev, 1435 "configuration of DMA failed, fall back to interrupt mode\n"); 1436 goto err_config_dma; 1437 } 1438 return; 1439 } 1440 1441err_config_dma: 1442 /* enable all interrupts except RX */ 1443 writew(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM, SSP_IMSC(pl022->virtbase)); 1444} 1445 1446static void do_interrupt_dma_transfer(struct pl022 *pl022) 1447{ 1448 /* 1449 * Default is to enable all interrupts except RX - 1450 * this will be enabled once TX is complete 1451 */ 1452 u32 irqflags = (u32)(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM); 1453 1454 /* Enable target chip, if not already active */ 1455 if (!pl022->next_msg_cs_active) 1456 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1457 1458 if (set_up_next_transfer(pl022, pl022->cur_transfer)) { 1459 /* Error path */ 1460 pl022->cur_msg->state = STATE_ERROR; 1461 pl022->cur_msg->status = -EIO; 1462 giveback(pl022); 1463 return; 1464 } 1465 /* If we're using DMA, set up DMA here */ 1466 if (pl022->cur_chip->enable_dma) { 1467 /* Configure DMA transfer */ 1468 if (configure_dma(pl022)) { 1469 dev_dbg(&pl022->adev->dev, 1470 "configuration of DMA failed, fall back to interrupt mode\n"); 1471 goto err_config_dma; 1472 } 1473 /* Disable interrupts in DMA mode, IRQ from DMA controller */ 1474 irqflags = DISABLE_ALL_INTERRUPTS; 1475 } 1476err_config_dma: 1477 /* Enable SSP, turn on interrupts */ 1478 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1479 SSP_CR1(pl022->virtbase)); 1480 writew(irqflags, SSP_IMSC(pl022->virtbase)); 1481} 1482 1483static void do_polling_transfer(struct pl022 *pl022) 1484{ 1485 struct spi_message *message = NULL; 1486 struct spi_transfer *transfer = NULL; 1487 struct spi_transfer *previous = NULL; 1488 struct chip_data *chip; 1489 unsigned long time, timeout; 1490 1491 chip = pl022->cur_chip; 1492 message = pl022->cur_msg; 1493 1494 while (message->state != STATE_DONE) { 1495 /* Handle for abort */ 1496 if (message->state == STATE_ERROR) 1497 break; 1498 transfer = pl022->cur_transfer; 1499 1500 /* Delay if requested at end of transfer */ 1501 if (message->state == STATE_RUNNING) { 1502 previous = 1503 list_entry(transfer->transfer_list.prev, 1504 struct spi_transfer, transfer_list); 1505 if (previous->delay_usecs) 1506 udelay(previous->delay_usecs); 1507 if (previous->cs_change) 1508 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1509 } else { 1510 /* STATE_START */ 1511 message->state = STATE_RUNNING; 1512 if (!pl022->next_msg_cs_active) 1513 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1514 } 1515 1516 /* Configuration Changing Per Transfer */ 1517 if (set_up_next_transfer(pl022, transfer)) { 1518 /* Error path */ 1519 message->state = STATE_ERROR; 1520 break; 1521 } 1522 /* Flush FIFOs and enable SSP */ 1523 flush(pl022); 1524 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1525 SSP_CR1(pl022->virtbase)); 1526 1527 dev_dbg(&pl022->adev->dev, "polling transfer ongoing ...\n"); 1528 1529 timeout = jiffies + msecs_to_jiffies(SPI_POLLING_TIMEOUT); 1530 while (pl022->tx < pl022->tx_end || pl022->rx < pl022->rx_end) { 1531 time = jiffies; 1532 readwriter(pl022); 1533 if (time_after(time, timeout)) { 1534 dev_warn(&pl022->adev->dev, 1535 "%s: timeout!\n", __func__); 1536 message->state = STATE_ERROR; 1537 goto out; 1538 } 1539 cpu_relax(); 1540 } 1541 1542 /* Update total byte transferred */ 1543 message->actual_length += pl022->cur_transfer->len; 1544 if (pl022->cur_transfer->cs_change) 1545 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1546 /* Move to next transfer */ 1547 message->state = next_transfer(pl022); 1548 } 1549out: 1550 /* Handle end of message */ 1551 if (message->state == STATE_DONE) 1552 message->status = 0; 1553 else 1554 message->status = -EIO; 1555 1556 giveback(pl022); 1557 return; 1558} 1559 1560static int pl022_transfer_one_message(struct spi_master *master, 1561 struct spi_message *msg) 1562{ 1563 struct pl022 *pl022 = spi_master_get_devdata(master); 1564 1565 /* Initial message state */ 1566 pl022->cur_msg = msg; 1567 msg->state = STATE_START; 1568 1569 pl022->cur_transfer = list_entry(msg->transfers.next, 1570 struct spi_transfer, transfer_list); 1571 1572 /* Setup the SPI using the per chip configuration */ 1573 pl022->cur_chip = spi_get_ctldata(msg->spi); 1574 pl022->cur_cs = pl022->chipselects[msg->spi->chip_select]; 1575 1576 restore_state(pl022); 1577 flush(pl022); 1578 1579 if (pl022->cur_chip->xfer_type == POLLING_TRANSFER) 1580 do_polling_transfer(pl022); 1581 else 1582 do_interrupt_dma_transfer(pl022); 1583 1584 return 0; 1585} 1586 1587static int pl022_unprepare_transfer_hardware(struct spi_master *master) 1588{ 1589 struct pl022 *pl022 = spi_master_get_devdata(master); 1590 1591 /* nothing more to do - disable spi/ssp and power off */ 1592 writew((readw(SSP_CR1(pl022->virtbase)) & 1593 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1594 1595 return 0; 1596} 1597 1598static int verify_controller_parameters(struct pl022 *pl022, 1599 struct pl022_config_chip const *chip_info) 1600{ 1601 if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI) 1602 || (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) { 1603 dev_err(&pl022->adev->dev, 1604 "interface is configured incorrectly\n"); 1605 return -EINVAL; 1606 } 1607 if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) && 1608 (!pl022->vendor->unidir)) { 1609 dev_err(&pl022->adev->dev, 1610 "unidirectional mode not supported in this " 1611 "hardware version\n"); 1612 return -EINVAL; 1613 } 1614 if ((chip_info->hierarchy != SSP_MASTER) 1615 && (chip_info->hierarchy != SSP_SLAVE)) { 1616 dev_err(&pl022->adev->dev, 1617 "hierarchy is configured incorrectly\n"); 1618 return -EINVAL; 1619 } 1620 if ((chip_info->com_mode != INTERRUPT_TRANSFER) 1621 && (chip_info->com_mode != DMA_TRANSFER) 1622 && (chip_info->com_mode != POLLING_TRANSFER)) { 1623 dev_err(&pl022->adev->dev, 1624 "Communication mode is configured incorrectly\n"); 1625 return -EINVAL; 1626 } 1627 switch (chip_info->rx_lev_trig) { 1628 case SSP_RX_1_OR_MORE_ELEM: 1629 case SSP_RX_4_OR_MORE_ELEM: 1630 case SSP_RX_8_OR_MORE_ELEM: 1631 /* These are always OK, all variants can handle this */ 1632 break; 1633 case SSP_RX_16_OR_MORE_ELEM: 1634 if (pl022->vendor->fifodepth < 16) { 1635 dev_err(&pl022->adev->dev, 1636 "RX FIFO Trigger Level is configured incorrectly\n"); 1637 return -EINVAL; 1638 } 1639 break; 1640 case SSP_RX_32_OR_MORE_ELEM: 1641 if (pl022->vendor->fifodepth < 32) { 1642 dev_err(&pl022->adev->dev, 1643 "RX FIFO Trigger Level is configured incorrectly\n"); 1644 return -EINVAL; 1645 } 1646 break; 1647 default: 1648 dev_err(&pl022->adev->dev, 1649 "RX FIFO Trigger Level is configured incorrectly\n"); 1650 return -EINVAL; 1651 } 1652 switch (chip_info->tx_lev_trig) { 1653 case SSP_TX_1_OR_MORE_EMPTY_LOC: 1654 case SSP_TX_4_OR_MORE_EMPTY_LOC: 1655 case SSP_TX_8_OR_MORE_EMPTY_LOC: 1656 /* These are always OK, all variants can handle this */ 1657 break; 1658 case SSP_TX_16_OR_MORE_EMPTY_LOC: 1659 if (pl022->vendor->fifodepth < 16) { 1660 dev_err(&pl022->adev->dev, 1661 "TX FIFO Trigger Level is configured incorrectly\n"); 1662 return -EINVAL; 1663 } 1664 break; 1665 case SSP_TX_32_OR_MORE_EMPTY_LOC: 1666 if (pl022->vendor->fifodepth < 32) { 1667 dev_err(&pl022->adev->dev, 1668 "TX FIFO Trigger Level is configured incorrectly\n"); 1669 return -EINVAL; 1670 } 1671 break; 1672 default: 1673 dev_err(&pl022->adev->dev, 1674 "TX FIFO Trigger Level is configured incorrectly\n"); 1675 return -EINVAL; 1676 } 1677 if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) { 1678 if ((chip_info->ctrl_len < SSP_BITS_4) 1679 || (chip_info->ctrl_len > SSP_BITS_32)) { 1680 dev_err(&pl022->adev->dev, 1681 "CTRL LEN is configured incorrectly\n"); 1682 return -EINVAL; 1683 } 1684 if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO) 1685 && (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) { 1686 dev_err(&pl022->adev->dev, 1687 "Wait State is configured incorrectly\n"); 1688 return -EINVAL; 1689 } 1690 /* Half duplex is only available in the ST Micro version */ 1691 if (pl022->vendor->extended_cr) { 1692 if ((chip_info->duplex != 1693 SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1694 && (chip_info->duplex != 1695 SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) { 1696 dev_err(&pl022->adev->dev, 1697 "Microwire duplex mode is configured incorrectly\n"); 1698 return -EINVAL; 1699 } 1700 } else { 1701 if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1702 dev_err(&pl022->adev->dev, 1703 "Microwire half duplex mode requested," 1704 " but this is only available in the" 1705 " ST version of PL022\n"); 1706 return -EINVAL; 1707 } 1708 } 1709 return 0; 1710} 1711 1712static inline u32 spi_rate(u32 rate, u16 cpsdvsr, u16 scr) 1713{ 1714 return rate / (cpsdvsr * (1 + scr)); 1715} 1716 1717static int calculate_effective_freq(struct pl022 *pl022, int freq, struct 1718 ssp_clock_params * clk_freq) 1719{ 1720 /* Lets calculate the frequency parameters */ 1721 u16 cpsdvsr = CPSDVR_MIN, scr = SCR_MIN; 1722 u32 rate, max_tclk, min_tclk, best_freq = 0, best_cpsdvsr = 0, 1723 best_scr = 0, tmp, found = 0; 1724 1725 rate = clk_get_rate(pl022->clk); 1726 /* cpsdvscr = 2 & scr 0 */ 1727 max_tclk = spi_rate(rate, CPSDVR_MIN, SCR_MIN); 1728 /* cpsdvsr = 254 & scr = 255 */ 1729 min_tclk = spi_rate(rate, CPSDVR_MAX, SCR_MAX); 1730 1731 if (freq > max_tclk) 1732 dev_warn(&pl022->adev->dev, 1733 "Max speed that can be programmed is %d Hz, you requested %d\n", 1734 max_tclk, freq); 1735 1736 if (freq < min_tclk) { 1737 dev_err(&pl022->adev->dev, 1738 "Requested frequency: %d Hz is less than minimum possible %d Hz\n", 1739 freq, min_tclk); 1740 return -EINVAL; 1741 } 1742 1743 /* 1744 * best_freq will give closest possible available rate (<= requested 1745 * freq) for all values of scr & cpsdvsr. 1746 */ 1747 while ((cpsdvsr <= CPSDVR_MAX) && !found) { 1748 while (scr <= SCR_MAX) { 1749 tmp = spi_rate(rate, cpsdvsr, scr); 1750 1751 if (tmp > freq) { 1752 /* we need lower freq */ 1753 scr++; 1754 continue; 1755 } 1756 1757 /* 1758 * If found exact value, mark found and break. 1759 * If found more closer value, update and break. 1760 */ 1761 if (tmp > best_freq) { 1762 best_freq = tmp; 1763 best_cpsdvsr = cpsdvsr; 1764 best_scr = scr; 1765 1766 if (tmp == freq) 1767 found = 1; 1768 } 1769 /* 1770 * increased scr will give lower rates, which are not 1771 * required 1772 */ 1773 break; 1774 } 1775 cpsdvsr += 2; 1776 scr = SCR_MIN; 1777 } 1778 1779 WARN(!best_freq, "pl022: Matching cpsdvsr and scr not found for %d Hz rate \n", 1780 freq); 1781 1782 clk_freq->cpsdvsr = (u8) (best_cpsdvsr & 0xFF); 1783 clk_freq->scr = (u8) (best_scr & 0xFF); 1784 dev_dbg(&pl022->adev->dev, 1785 "SSP Target Frequency is: %u, Effective Frequency is %u\n", 1786 freq, best_freq); 1787 dev_dbg(&pl022->adev->dev, "SSP cpsdvsr = %d, scr = %d\n", 1788 clk_freq->cpsdvsr, clk_freq->scr); 1789 1790 return 0; 1791} 1792 1793/* 1794 * A piece of default chip info unless the platform 1795 * supplies it. 1796 */ 1797static const struct pl022_config_chip pl022_default_chip_info = { 1798 .com_mode = POLLING_TRANSFER, 1799 .iface = SSP_INTERFACE_MOTOROLA_SPI, 1800 .hierarchy = SSP_SLAVE, 1801 .slave_tx_disable = DO_NOT_DRIVE_TX, 1802 .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, 1803 .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, 1804 .ctrl_len = SSP_BITS_8, 1805 .wait_state = SSP_MWIRE_WAIT_ZERO, 1806 .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, 1807 .cs_control = null_cs_control, 1808}; 1809 1810/** 1811 * pl022_setup - setup function registered to SPI master framework 1812 * @spi: spi device which is requesting setup 1813 * 1814 * This function is registered to the SPI framework for this SPI master 1815 * controller. If it is the first time when setup is called by this device, 1816 * this function will initialize the runtime state for this chip and save 1817 * the same in the device structure. Else it will update the runtime info 1818 * with the updated chip info. Nothing is really being written to the 1819 * controller hardware here, that is not done until the actual transfer 1820 * commence. 1821 */ 1822static int pl022_setup(struct spi_device *spi) 1823{ 1824 struct pl022_config_chip const *chip_info; 1825 struct pl022_config_chip chip_info_dt; 1826 struct chip_data *chip; 1827 struct ssp_clock_params clk_freq = { .cpsdvsr = 0, .scr = 0}; 1828 int status = 0; 1829 struct pl022 *pl022 = spi_master_get_devdata(spi->master); 1830 unsigned int bits = spi->bits_per_word; 1831 u32 tmp; 1832 struct device_node *np = spi->dev.of_node; 1833 1834 if (!spi->max_speed_hz) 1835 return -EINVAL; 1836 1837 /* Get controller_state if one is supplied */ 1838 chip = spi_get_ctldata(spi); 1839 1840 if (chip == NULL) { 1841 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); 1842 if (!chip) 1843 return -ENOMEM; 1844 dev_dbg(&spi->dev, 1845 "allocated memory for controller's runtime state\n"); 1846 } 1847 1848 /* Get controller data if one is supplied */ 1849 chip_info = spi->controller_data; 1850 1851 if (chip_info == NULL) { 1852 if (np) { 1853 chip_info_dt = pl022_default_chip_info; 1854 1855 chip_info_dt.hierarchy = SSP_MASTER; 1856 of_property_read_u32(np, "pl022,interface", 1857 &chip_info_dt.iface); 1858 of_property_read_u32(np, "pl022,com-mode", 1859 &chip_info_dt.com_mode); 1860 of_property_read_u32(np, "pl022,rx-level-trig", 1861 &chip_info_dt.rx_lev_trig); 1862 of_property_read_u32(np, "pl022,tx-level-trig", 1863 &chip_info_dt.tx_lev_trig); 1864 of_property_read_u32(np, "pl022,ctrl-len", 1865 &chip_info_dt.ctrl_len); 1866 of_property_read_u32(np, "pl022,wait-state", 1867 &chip_info_dt.wait_state); 1868 of_property_read_u32(np, "pl022,duplex", 1869 &chip_info_dt.duplex); 1870 1871 chip_info = &chip_info_dt; 1872 } else { 1873 chip_info = &pl022_default_chip_info; 1874 /* spi_board_info.controller_data not is supplied */ 1875 dev_dbg(&spi->dev, 1876 "using default controller_data settings\n"); 1877 } 1878 } else 1879 dev_dbg(&spi->dev, 1880 "using user supplied controller_data settings\n"); 1881 1882 /* 1883 * We can override with custom divisors, else we use the board 1884 * frequency setting 1885 */ 1886 if ((0 == chip_info->clk_freq.cpsdvsr) 1887 && (0 == chip_info->clk_freq.scr)) { 1888 status = calculate_effective_freq(pl022, 1889 spi->max_speed_hz, 1890 &clk_freq); 1891 if (status < 0) 1892 goto err_config_params; 1893 } else { 1894 memcpy(&clk_freq, &chip_info->clk_freq, sizeof(clk_freq)); 1895 if ((clk_freq.cpsdvsr % 2) != 0) 1896 clk_freq.cpsdvsr = 1897 clk_freq.cpsdvsr - 1; 1898 } 1899 if ((clk_freq.cpsdvsr < CPSDVR_MIN) 1900 || (clk_freq.cpsdvsr > CPSDVR_MAX)) { 1901 status = -EINVAL; 1902 dev_err(&spi->dev, 1903 "cpsdvsr is configured incorrectly\n"); 1904 goto err_config_params; 1905 } 1906 1907 status = verify_controller_parameters(pl022, chip_info); 1908 if (status) { 1909 dev_err(&spi->dev, "controller data is incorrect"); 1910 goto err_config_params; 1911 } 1912 1913 pl022->rx_lev_trig = chip_info->rx_lev_trig; 1914 pl022->tx_lev_trig = chip_info->tx_lev_trig; 1915 1916 /* Now set controller state based on controller data */ 1917 chip->xfer_type = chip_info->com_mode; 1918 if (!chip_info->cs_control) { 1919 chip->cs_control = null_cs_control; 1920 if (!gpio_is_valid(pl022->chipselects[spi->chip_select])) 1921 dev_warn(&spi->dev, 1922 "invalid chip select\n"); 1923 } else 1924 chip->cs_control = chip_info->cs_control; 1925 1926 /* Check bits per word with vendor specific range */ 1927 if ((bits <= 3) || (bits > pl022->vendor->max_bpw)) { 1928 status = -ENOTSUPP; 1929 dev_err(&spi->dev, "illegal data size for this controller!\n"); 1930 dev_err(&spi->dev, "This controller can only handle 4 <= n <= %d bit words\n", 1931 pl022->vendor->max_bpw); 1932 goto err_config_params; 1933 } else if (bits <= 8) { 1934 dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n"); 1935 chip->n_bytes = 1; 1936 chip->read = READING_U8; 1937 chip->write = WRITING_U8; 1938 } else if (bits <= 16) { 1939 dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n"); 1940 chip->n_bytes = 2; 1941 chip->read = READING_U16; 1942 chip->write = WRITING_U16; 1943 } else { 1944 dev_dbg(&spi->dev, "17 <= n <= 32 bits per word\n"); 1945 chip->n_bytes = 4; 1946 chip->read = READING_U32; 1947 chip->write = WRITING_U32; 1948 } 1949 1950 /* Now Initialize all register settings required for this chip */ 1951 chip->cr0 = 0; 1952 chip->cr1 = 0; 1953 chip->dmacr = 0; 1954 chip->cpsr = 0; 1955 if ((chip_info->com_mode == DMA_TRANSFER) 1956 && ((pl022->master_info)->enable_dma)) { 1957 chip->enable_dma = true; 1958 dev_dbg(&spi->dev, "DMA mode set in controller state\n"); 1959 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1960 SSP_DMACR_MASK_RXDMAE, 0); 1961 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1962 SSP_DMACR_MASK_TXDMAE, 1); 1963 } else { 1964 chip->enable_dma = false; 1965 dev_dbg(&spi->dev, "DMA mode NOT set in controller state\n"); 1966 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1967 SSP_DMACR_MASK_RXDMAE, 0); 1968 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1969 SSP_DMACR_MASK_TXDMAE, 1); 1970 } 1971 1972 chip->cpsr = clk_freq.cpsdvsr; 1973 1974 /* Special setup for the ST micro extended control registers */ 1975 if (pl022->vendor->extended_cr) { 1976 u32 etx; 1977 1978 if (pl022->vendor->pl023) { 1979 /* These bits are only in the PL023 */ 1980 SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay, 1981 SSP_CR1_MASK_FBCLKDEL_ST, 13); 1982 } else { 1983 /* These bits are in the PL022 but not PL023 */ 1984 SSP_WRITE_BITS(chip->cr0, chip_info->duplex, 1985 SSP_CR0_MASK_HALFDUP_ST, 5); 1986 SSP_WRITE_BITS(chip->cr0, chip_info->ctrl_len, 1987 SSP_CR0_MASK_CSS_ST, 16); 1988 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 1989 SSP_CR0_MASK_FRF_ST, 21); 1990 SSP_WRITE_BITS(chip->cr1, chip_info->wait_state, 1991 SSP_CR1_MASK_MWAIT_ST, 6); 1992 } 1993 SSP_WRITE_BITS(chip->cr0, bits - 1, 1994 SSP_CR0_MASK_DSS_ST, 0); 1995 1996 if (spi->mode & SPI_LSB_FIRST) { 1997 tmp = SSP_RX_LSB; 1998 etx = SSP_TX_LSB; 1999 } else { 2000 tmp = SSP_RX_MSB; 2001 etx = SSP_TX_MSB; 2002 } 2003 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4); 2004 SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5); 2005 SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig, 2006 SSP_CR1_MASK_RXIFLSEL_ST, 7); 2007 SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig, 2008 SSP_CR1_MASK_TXIFLSEL_ST, 10); 2009 } else { 2010 SSP_WRITE_BITS(chip->cr0, bits - 1, 2011 SSP_CR0_MASK_DSS, 0); 2012 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 2013 SSP_CR0_MASK_FRF, 4); 2014 } 2015 2016 /* Stuff that is common for all versions */ 2017 if (spi->mode & SPI_CPOL) 2018 tmp = SSP_CLK_POL_IDLE_HIGH; 2019 else 2020 tmp = SSP_CLK_POL_IDLE_LOW; 2021 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6); 2022 2023 if (spi->mode & SPI_CPHA) 2024 tmp = SSP_CLK_SECOND_EDGE; 2025 else 2026 tmp = SSP_CLK_FIRST_EDGE; 2027 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7); 2028 2029 SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8); 2030 /* Loopback is available on all versions except PL023 */ 2031 if (pl022->vendor->loopback) { 2032 if (spi->mode & SPI_LOOP) 2033 tmp = LOOPBACK_ENABLED; 2034 else 2035 tmp = LOOPBACK_DISABLED; 2036 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0); 2037 } 2038 SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1); 2039 SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2); 2040 SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 2041 3); 2042 2043 /* Save controller_state */ 2044 spi_set_ctldata(spi, chip); 2045 return status; 2046 err_config_params: 2047 spi_set_ctldata(spi, NULL); 2048 kfree(chip); 2049 return status; 2050} 2051 2052/** 2053 * pl022_cleanup - cleanup function registered to SPI master framework 2054 * @spi: spi device which is requesting cleanup 2055 * 2056 * This function is registered to the SPI framework for this SPI master 2057 * controller. It will free the runtime state of chip. 2058 */ 2059static void pl022_cleanup(struct spi_device *spi) 2060{ 2061 struct chip_data *chip = spi_get_ctldata(spi); 2062 2063 spi_set_ctldata(spi, NULL); 2064 kfree(chip); 2065} 2066 2067static struct pl022_ssp_controller * 2068pl022_platform_data_dt_get(struct device *dev) 2069{ 2070 struct device_node *np = dev->of_node; 2071 struct pl022_ssp_controller *pd; 2072 u32 tmp; 2073 2074 if (!np) { 2075 dev_err(dev, "no dt node defined\n"); 2076 return NULL; 2077 } 2078 2079 pd = devm_kzalloc(dev, sizeof(struct pl022_ssp_controller), GFP_KERNEL); 2080 if (!pd) 2081 return NULL; 2082 2083 pd->bus_id = -1; 2084 pd->enable_dma = 1; 2085 of_property_read_u32(np, "num-cs", &tmp); 2086 pd->num_chipselect = tmp; 2087 of_property_read_u32(np, "pl022,autosuspend-delay", 2088 &pd->autosuspend_delay); 2089 pd->rt = of_property_read_bool(np, "pl022,rt"); 2090 2091 return pd; 2092} 2093 2094static int pl022_probe(struct amba_device *adev, const struct amba_id *id) 2095{ 2096 struct device *dev = &adev->dev; 2097 struct pl022_ssp_controller *platform_info = 2098 dev_get_platdata(&adev->dev); 2099 struct spi_master *master; 2100 struct pl022 *pl022 = NULL; /*Data for this driver */ 2101 struct device_node *np = adev->dev.of_node; 2102 int status = 0, i, num_cs; 2103 2104 dev_info(&adev->dev, 2105 "ARM PL022 driver, device ID: 0x%08x\n", adev->periphid); 2106 if (!platform_info && IS_ENABLED(CONFIG_OF)) 2107 platform_info = pl022_platform_data_dt_get(dev); 2108 2109 if (!platform_info) { 2110 dev_err(dev, "probe: no platform data defined\n"); 2111 return -ENODEV; 2112 } 2113 2114 if (platform_info->num_chipselect) { 2115 num_cs = platform_info->num_chipselect; 2116 } else { 2117 dev_err(dev, "probe: no chip select defined\n"); 2118 return -ENODEV; 2119 } 2120 2121 /* Allocate master with space for data */ 2122 master = spi_alloc_master(dev, sizeof(struct pl022)); 2123 if (master == NULL) { 2124 dev_err(&adev->dev, "probe - cannot alloc SPI master\n"); 2125 return -ENOMEM; 2126 } 2127 2128 pl022 = spi_master_get_devdata(master); 2129 pl022->master = master; 2130 pl022->master_info = platform_info; 2131 pl022->adev = adev; 2132 pl022->vendor = id->data; 2133 pl022->chipselects = devm_kzalloc(dev, num_cs * sizeof(int), 2134 GFP_KERNEL); 2135 if (!pl022->chipselects) { 2136 status = -ENOMEM; 2137 goto err_no_mem; 2138 } 2139 2140 /* 2141 * Bus Number Which has been Assigned to this SSP controller 2142 * on this board 2143 */ 2144 master->bus_num = platform_info->bus_id; 2145 master->num_chipselect = num_cs; 2146 master->cleanup = pl022_cleanup; 2147 master->setup = pl022_setup; 2148 master->auto_runtime_pm = true; 2149 master->transfer_one_message = pl022_transfer_one_message; 2150 master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware; 2151 master->rt = platform_info->rt; 2152 master->dev.of_node = dev->of_node; 2153 2154 if (platform_info->num_chipselect && platform_info->chipselects) { 2155 for (i = 0; i < num_cs; i++) 2156 pl022->chipselects[i] = platform_info->chipselects[i]; 2157 } else if (pl022->vendor->internal_cs_ctrl) { 2158 for (i = 0; i < num_cs; i++) 2159 pl022->chipselects[i] = i; 2160 } else if (IS_ENABLED(CONFIG_OF)) { 2161 for (i = 0; i < num_cs; i++) { 2162 int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); 2163 2164 if (cs_gpio == -EPROBE_DEFER) { 2165 status = -EPROBE_DEFER; 2166 goto err_no_gpio; 2167 } 2168 2169 pl022->chipselects[i] = cs_gpio; 2170 2171 if (gpio_is_valid(cs_gpio)) { 2172 if (devm_gpio_request(dev, cs_gpio, "ssp-pl022")) 2173 dev_err(&adev->dev, 2174 "could not request %d gpio\n", 2175 cs_gpio); 2176 else if (gpio_direction_output(cs_gpio, 1)) 2177 dev_err(&adev->dev, 2178 "could not set gpio %d as output\n", 2179 cs_gpio); 2180 } 2181 } 2182 } 2183 2184 /* 2185 * Supports mode 0-3, loopback, and active low CS. Transfers are 2186 * always MS bit first on the original pl022. 2187 */ 2188 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP; 2189 if (pl022->vendor->extended_cr) 2190 master->mode_bits |= SPI_LSB_FIRST; 2191 2192 dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num); 2193 2194 status = amba_request_regions(adev, NULL); 2195 if (status) 2196 goto err_no_ioregion; 2197 2198 pl022->phybase = adev->res.start; 2199 pl022->virtbase = devm_ioremap(dev, adev->res.start, 2200 resource_size(&adev->res)); 2201 if (pl022->virtbase == NULL) { 2202 status = -ENOMEM; 2203 goto err_no_ioremap; 2204 } 2205 dev_info(&adev->dev, "mapped registers from %pa to %p\n", 2206 &adev->res.start, pl022->virtbase); 2207 2208 pl022->clk = devm_clk_get(&adev->dev, NULL); 2209 if (IS_ERR(pl022->clk)) { 2210 status = PTR_ERR(pl022->clk); 2211 dev_err(&adev->dev, "could not retrieve SSP/SPI bus clock\n"); 2212 goto err_no_clk; 2213 } 2214 2215 status = clk_prepare_enable(pl022->clk); 2216 if (status) { 2217 dev_err(&adev->dev, "could not enable SSP/SPI bus clock\n"); 2218 goto err_no_clk_en; 2219 } 2220 2221 /* Initialize transfer pump */ 2222 tasklet_init(&pl022->pump_transfers, pump_transfers, 2223 (unsigned long)pl022); 2224 2225 /* Disable SSP */ 2226 writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)), 2227 SSP_CR1(pl022->virtbase)); 2228 load_ssp_default_config(pl022); 2229 2230 status = devm_request_irq(dev, adev->irq[0], pl022_interrupt_handler, 2231 0, "pl022", pl022); 2232 if (status < 0) { 2233 dev_err(&adev->dev, "probe - cannot get IRQ (%d)\n", status); 2234 goto err_no_irq; 2235 } 2236 2237 /* Get DMA channels, try autoconfiguration first */ 2238 status = pl022_dma_autoprobe(pl022); 2239 2240 /* If that failed, use channels from platform_info */ 2241 if (status == 0) 2242 platform_info->enable_dma = 1; 2243 else if (platform_info->enable_dma) { 2244 status = pl022_dma_probe(pl022); 2245 if (status != 0) 2246 platform_info->enable_dma = 0; 2247 } 2248 2249 /* Register with the SPI framework */ 2250 amba_set_drvdata(adev, pl022); 2251 status = devm_spi_register_master(&adev->dev, master); 2252 if (status != 0) { 2253 dev_err(&adev->dev, 2254 "probe - problem registering spi master\n"); 2255 goto err_spi_register; 2256 } 2257 dev_dbg(dev, "probe succeeded\n"); 2258 2259 /* let runtime pm put suspend */ 2260 if (platform_info->autosuspend_delay > 0) { 2261 dev_info(&adev->dev, 2262 "will use autosuspend for runtime pm, delay %dms\n", 2263 platform_info->autosuspend_delay); 2264 pm_runtime_set_autosuspend_delay(dev, 2265 platform_info->autosuspend_delay); 2266 pm_runtime_use_autosuspend(dev); 2267 } 2268 pm_runtime_put(dev); 2269 2270 return 0; 2271 2272 err_spi_register: 2273 if (platform_info->enable_dma) 2274 pl022_dma_remove(pl022); 2275 err_no_irq: 2276 clk_disable_unprepare(pl022->clk); 2277 err_no_clk_en: 2278 err_no_clk: 2279 err_no_ioremap: 2280 amba_release_regions(adev); 2281 err_no_ioregion: 2282 err_no_gpio: 2283 err_no_mem: 2284 spi_master_put(master); 2285 return status; 2286} 2287 2288static int 2289pl022_remove(struct amba_device *adev) 2290{ 2291 struct pl022 *pl022 = amba_get_drvdata(adev); 2292 2293 if (!pl022) 2294 return 0; 2295 2296 /* 2297 * undo pm_runtime_put() in probe. I assume that we're not 2298 * accessing the primecell here. 2299 */ 2300 pm_runtime_get_noresume(&adev->dev); 2301 2302 load_ssp_default_config(pl022); 2303 if (pl022->master_info->enable_dma) 2304 pl022_dma_remove(pl022); 2305 2306 clk_disable_unprepare(pl022->clk); 2307 amba_release_regions(adev); 2308 tasklet_disable(&pl022->pump_transfers); 2309 return 0; 2310} 2311 2312#ifdef CONFIG_PM_SLEEP 2313static int pl022_suspend(struct device *dev) 2314{ 2315 struct pl022 *pl022 = dev_get_drvdata(dev); 2316 int ret; 2317 2318 ret = spi_master_suspend(pl022->master); 2319 if (ret) { 2320 dev_warn(dev, "cannot suspend master\n"); 2321 return ret; 2322 } 2323 2324 ret = pm_runtime_force_suspend(dev); 2325 if (ret) { 2326 spi_master_resume(pl022->master); 2327 return ret; 2328 } 2329 2330 pinctrl_pm_select_sleep_state(dev); 2331 2332 dev_dbg(dev, "suspended\n"); 2333 return 0; 2334} 2335 2336static int pl022_resume(struct device *dev) 2337{ 2338 struct pl022 *pl022 = dev_get_drvdata(dev); 2339 int ret; 2340 2341 ret = pm_runtime_force_resume(dev); 2342 if (ret) 2343 dev_err(dev, "problem resuming\n"); 2344 2345 /* Start the queue running */ 2346 ret = spi_master_resume(pl022->master); 2347 if (ret) 2348 dev_err(dev, "problem starting queue (%d)\n", ret); 2349 else 2350 dev_dbg(dev, "resumed\n"); 2351 2352 return ret; 2353} 2354#endif 2355 2356#ifdef CONFIG_PM 2357static int pl022_runtime_suspend(struct device *dev) 2358{ 2359 struct pl022 *pl022 = dev_get_drvdata(dev); 2360 2361 clk_disable_unprepare(pl022->clk); 2362 pinctrl_pm_select_idle_state(dev); 2363 2364 return 0; 2365} 2366 2367static int pl022_runtime_resume(struct device *dev) 2368{ 2369 struct pl022 *pl022 = dev_get_drvdata(dev); 2370 2371 pinctrl_pm_select_default_state(dev); 2372 clk_prepare_enable(pl022->clk); 2373 2374 return 0; 2375} 2376#endif 2377 2378static const struct dev_pm_ops pl022_dev_pm_ops = { 2379 SET_SYSTEM_SLEEP_PM_OPS(pl022_suspend, pl022_resume) 2380 SET_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL) 2381}; 2382 2383static struct vendor_data vendor_arm = { 2384 .fifodepth = 8, 2385 .max_bpw = 16, 2386 .unidir = false, 2387 .extended_cr = false, 2388 .pl023 = false, 2389 .loopback = true, 2390 .internal_cs_ctrl = false, 2391}; 2392 2393static struct vendor_data vendor_st = { 2394 .fifodepth = 32, 2395 .max_bpw = 32, 2396 .unidir = false, 2397 .extended_cr = true, 2398 .pl023 = false, 2399 .loopback = true, 2400 .internal_cs_ctrl = false, 2401}; 2402 2403static struct vendor_data vendor_st_pl023 = { 2404 .fifodepth = 32, 2405 .max_bpw = 32, 2406 .unidir = false, 2407 .extended_cr = true, 2408 .pl023 = true, 2409 .loopback = false, 2410 .internal_cs_ctrl = false, 2411}; 2412 2413static struct vendor_data vendor_lsi = { 2414 .fifodepth = 8, 2415 .max_bpw = 16, 2416 .unidir = false, 2417 .extended_cr = false, 2418 .pl023 = false, 2419 .loopback = true, 2420 .internal_cs_ctrl = true, 2421}; 2422 2423static struct amba_id pl022_ids[] = { 2424 { 2425 /* 2426 * ARM PL022 variant, this has a 16bit wide 2427 * and 8 locations deep TX/RX FIFO 2428 */ 2429 .id = 0x00041022, 2430 .mask = 0x000fffff, 2431 .data = &vendor_arm, 2432 }, 2433 { 2434 /* 2435 * ST Micro derivative, this has 32bit wide 2436 * and 32 locations deep TX/RX FIFO 2437 */ 2438 .id = 0x01080022, 2439 .mask = 0xffffffff, 2440 .data = &vendor_st, 2441 }, 2442 { 2443 /* 2444 * ST-Ericsson derivative "PL023" (this is not 2445 * an official ARM number), this is a PL022 SSP block 2446 * stripped to SPI mode only, it has 32bit wide 2447 * and 32 locations deep TX/RX FIFO but no extended 2448 * CR0/CR1 register 2449 */ 2450 .id = 0x00080023, 2451 .mask = 0xffffffff, 2452 .data = &vendor_st_pl023, 2453 }, 2454 { 2455 /* 2456 * PL022 variant that has a chip select control register whih 2457 * allows control of 5 output signals nCS[0:4]. 2458 */ 2459 .id = 0x000b6022, 2460 .mask = 0x000fffff, 2461 .data = &vendor_lsi, 2462 }, 2463 { 0, 0 }, 2464}; 2465 2466MODULE_DEVICE_TABLE(amba, pl022_ids); 2467 2468static struct amba_driver pl022_driver = { 2469 .drv = { 2470 .name = "ssp-pl022", 2471 .pm = &pl022_dev_pm_ops, 2472 }, 2473 .id_table = pl022_ids, 2474 .probe = pl022_probe, 2475 .remove = pl022_remove, 2476}; 2477 2478static int __init pl022_init(void) 2479{ 2480 return amba_driver_register(&pl022_driver); 2481} 2482subsys_initcall(pl022_init); 2483 2484static void __exit pl022_exit(void) 2485{ 2486 amba_driver_unregister(&pl022_driver); 2487} 2488module_exit(pl022_exit); 2489 2490MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>"); 2491MODULE_DESCRIPTION("PL022 SSP Controller Driver"); 2492MODULE_LICENSE("GPL"); 2493