1/* 2 * Core routines and tables shareable across OS platforms. 3 * 4 * Copyright (c) 1994-2002 Justin T. Gibbs. 5 * Copyright (c) 2000-2002 Adaptec Inc. 6 * All rights reserved. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions, and the following disclaimer, 13 * without modification. 14 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 15 * substantially similar to the "NO WARRANTY" disclaimer below 16 * ("Disclaimer") and any redistribution must be conditioned upon 17 * including a substantially similar Disclaimer requirement for further 18 * binary redistribution. 19 * 3. Neither the names of the above-listed copyright holders nor the names 20 * of any contributors may be used to endorse or promote products derived 21 * from this software without specific prior written permission. 22 * 23 * Alternatively, this software may be distributed under the terms of the 24 * GNU General Public License ("GPL") version 2 as published by the Free 25 * Software Foundation. 26 * 27 * NO WARRANTY 28 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 29 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 30 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 31 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 32 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 33 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 34 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 35 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 36 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 37 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 38 * POSSIBILITY OF SUCH DAMAGES. 39 * 40 * $Id: //depot/aic7xxx/aic7xxx/aic7xxx.c#155 $ 41 */ 42 43#ifdef __linux__ 44#include "aic7xxx_osm.h" 45#include "aic7xxx_inline.h" 46#include "aicasm/aicasm_insformat.h" 47#else 48#include <dev/aic7xxx/aic7xxx_osm.h> 49#include <dev/aic7xxx/aic7xxx_inline.h> 50#include <dev/aic7xxx/aicasm/aicasm_insformat.h> 51#endif 52 53/***************************** Lookup Tables **********************************/ 54static const char *const ahc_chip_names[] = { 55 "NONE", 56 "aic7770", 57 "aic7850", 58 "aic7855", 59 "aic7859", 60 "aic7860", 61 "aic7870", 62 "aic7880", 63 "aic7895", 64 "aic7895C", 65 "aic7890/91", 66 "aic7896/97", 67 "aic7892", 68 "aic7899" 69}; 70static const u_int num_chip_names = ARRAY_SIZE(ahc_chip_names); 71 72/* 73 * Hardware error codes. 74 */ 75struct ahc_hard_error_entry { 76 uint8_t errno; 77 const char *errmesg; 78}; 79 80static const struct ahc_hard_error_entry ahc_hard_errors[] = { 81 { ILLHADDR, "Illegal Host Access" }, 82 { ILLSADDR, "Illegal Sequencer Address referrenced" }, 83 { ILLOPCODE, "Illegal Opcode in sequencer program" }, 84 { SQPARERR, "Sequencer Parity Error" }, 85 { DPARERR, "Data-path Parity Error" }, 86 { MPARERR, "Scratch or SCB Memory Parity Error" }, 87 { PCIERRSTAT, "PCI Error detected" }, 88 { CIOPARERR, "CIOBUS Parity Error" }, 89}; 90static const u_int num_errors = ARRAY_SIZE(ahc_hard_errors); 91 92static const struct ahc_phase_table_entry ahc_phase_table[] = 93{ 94 { P_DATAOUT, MSG_NOOP, "in Data-out phase" }, 95 { P_DATAIN, MSG_INITIATOR_DET_ERR, "in Data-in phase" }, 96 { P_DATAOUT_DT, MSG_NOOP, "in DT Data-out phase" }, 97 { P_DATAIN_DT, MSG_INITIATOR_DET_ERR, "in DT Data-in phase" }, 98 { P_COMMAND, MSG_NOOP, "in Command phase" }, 99 { P_MESGOUT, MSG_NOOP, "in Message-out phase" }, 100 { P_STATUS, MSG_INITIATOR_DET_ERR, "in Status phase" }, 101 { P_MESGIN, MSG_PARITY_ERROR, "in Message-in phase" }, 102 { P_BUSFREE, MSG_NOOP, "while idle" }, 103 { 0, MSG_NOOP, "in unknown phase" } 104}; 105 106/* 107 * In most cases we only wish to itterate over real phases, so 108 * exclude the last element from the count. 109 */ 110static const u_int num_phases = ARRAY_SIZE(ahc_phase_table) - 1; 111 112/* 113 * Valid SCSIRATE values. (p. 3-17) 114 * Provides a mapping of tranfer periods in ns to the proper value to 115 * stick in the scsixfer reg. 116 */ 117static const struct ahc_syncrate ahc_syncrates[] = 118{ 119 /* ultra2 fast/ultra period rate */ 120 { 0x42, 0x000, 9, "80.0" }, 121 { 0x03, 0x000, 10, "40.0" }, 122 { 0x04, 0x000, 11, "33.0" }, 123 { 0x05, 0x100, 12, "20.0" }, 124 { 0x06, 0x110, 15, "16.0" }, 125 { 0x07, 0x120, 18, "13.4" }, 126 { 0x08, 0x000, 25, "10.0" }, 127 { 0x19, 0x010, 31, "8.0" }, 128 { 0x1a, 0x020, 37, "6.67" }, 129 { 0x1b, 0x030, 43, "5.7" }, 130 { 0x1c, 0x040, 50, "5.0" }, 131 { 0x00, 0x050, 56, "4.4" }, 132 { 0x00, 0x060, 62, "4.0" }, 133 { 0x00, 0x070, 68, "3.6" }, 134 { 0x00, 0x000, 0, NULL } 135}; 136 137/* Our Sequencer Program */ 138#include "aic7xxx_seq.h" 139 140/**************************** Function Declarations ***************************/ 141static void ahc_force_renegotiation(struct ahc_softc *ahc, 142 struct ahc_devinfo *devinfo); 143static struct ahc_tmode_tstate* 144 ahc_alloc_tstate(struct ahc_softc *ahc, 145 u_int scsi_id, char channel); 146#ifdef AHC_TARGET_MODE 147static void ahc_free_tstate(struct ahc_softc *ahc, 148 u_int scsi_id, char channel, int force); 149#endif 150static const struct ahc_syncrate* 151 ahc_devlimited_syncrate(struct ahc_softc *ahc, 152 struct ahc_initiator_tinfo *, 153 u_int *period, 154 u_int *ppr_options, 155 role_t role); 156static void ahc_update_pending_scbs(struct ahc_softc *ahc); 157static void ahc_fetch_devinfo(struct ahc_softc *ahc, 158 struct ahc_devinfo *devinfo); 159static void ahc_scb_devinfo(struct ahc_softc *ahc, 160 struct ahc_devinfo *devinfo, 161 struct scb *scb); 162static void ahc_assert_atn(struct ahc_softc *ahc); 163static void ahc_setup_initiator_msgout(struct ahc_softc *ahc, 164 struct ahc_devinfo *devinfo, 165 struct scb *scb); 166static void ahc_build_transfer_msg(struct ahc_softc *ahc, 167 struct ahc_devinfo *devinfo); 168static void ahc_construct_sdtr(struct ahc_softc *ahc, 169 struct ahc_devinfo *devinfo, 170 u_int period, u_int offset); 171static void ahc_construct_wdtr(struct ahc_softc *ahc, 172 struct ahc_devinfo *devinfo, 173 u_int bus_width); 174static void ahc_construct_ppr(struct ahc_softc *ahc, 175 struct ahc_devinfo *devinfo, 176 u_int period, u_int offset, 177 u_int bus_width, u_int ppr_options); 178static void ahc_clear_msg_state(struct ahc_softc *ahc); 179static void ahc_handle_proto_violation(struct ahc_softc *ahc); 180static void ahc_handle_message_phase(struct ahc_softc *ahc); 181typedef enum { 182 AHCMSG_1B, 183 AHCMSG_2B, 184 AHCMSG_EXT 185} ahc_msgtype; 186static int ahc_sent_msg(struct ahc_softc *ahc, ahc_msgtype type, 187 u_int msgval, int full); 188static int ahc_parse_msg(struct ahc_softc *ahc, 189 struct ahc_devinfo *devinfo); 190static int ahc_handle_msg_reject(struct ahc_softc *ahc, 191 struct ahc_devinfo *devinfo); 192static void ahc_handle_ign_wide_residue(struct ahc_softc *ahc, 193 struct ahc_devinfo *devinfo); 194static void ahc_reinitialize_dataptrs(struct ahc_softc *ahc); 195static void ahc_handle_devreset(struct ahc_softc *ahc, 196 struct ahc_devinfo *devinfo, 197 cam_status status, char *message, 198 int verbose_level); 199#ifdef AHC_TARGET_MODE 200static void ahc_setup_target_msgin(struct ahc_softc *ahc, 201 struct ahc_devinfo *devinfo, 202 struct scb *scb); 203#endif 204 205static bus_dmamap_callback_t ahc_dmamap_cb; 206static void ahc_build_free_scb_list(struct ahc_softc *ahc); 207static int ahc_init_scbdata(struct ahc_softc *ahc); 208static void ahc_fini_scbdata(struct ahc_softc *ahc); 209static void ahc_qinfifo_requeue(struct ahc_softc *ahc, 210 struct scb *prev_scb, 211 struct scb *scb); 212static int ahc_qinfifo_count(struct ahc_softc *ahc); 213static u_int ahc_rem_scb_from_disc_list(struct ahc_softc *ahc, 214 u_int prev, u_int scbptr); 215static void ahc_add_curscb_to_free_list(struct ahc_softc *ahc); 216static u_int ahc_rem_wscb(struct ahc_softc *ahc, 217 u_int scbpos, u_int prev); 218static void ahc_reset_current_bus(struct ahc_softc *ahc); 219#ifdef AHC_DUMP_SEQ 220static void ahc_dumpseq(struct ahc_softc *ahc); 221#endif 222static int ahc_loadseq(struct ahc_softc *ahc); 223static int ahc_check_patch(struct ahc_softc *ahc, 224 const struct patch **start_patch, 225 u_int start_instr, u_int *skip_addr); 226static void ahc_download_instr(struct ahc_softc *ahc, 227 u_int instrptr, uint8_t *dconsts); 228#ifdef AHC_TARGET_MODE 229static void ahc_queue_lstate_event(struct ahc_softc *ahc, 230 struct ahc_tmode_lstate *lstate, 231 u_int initiator_id, 232 u_int event_type, 233 u_int event_arg); 234static void ahc_update_scsiid(struct ahc_softc *ahc, 235 u_int targid_mask); 236static int ahc_handle_target_cmd(struct ahc_softc *ahc, 237 struct target_cmd *cmd); 238#endif 239 240static u_int ahc_index_busy_tcl(struct ahc_softc *ahc, u_int tcl); 241static void ahc_unbusy_tcl(struct ahc_softc *ahc, u_int tcl); 242static void ahc_busy_tcl(struct ahc_softc *ahc, 243 u_int tcl, u_int busyid); 244 245/************************** SCB and SCB queue management **********************/ 246static void ahc_run_untagged_queues(struct ahc_softc *ahc); 247static void ahc_run_untagged_queue(struct ahc_softc *ahc, 248 struct scb_tailq *queue); 249 250/****************************** Initialization ********************************/ 251static void ahc_alloc_scbs(struct ahc_softc *ahc); 252static void ahc_shutdown(void *arg); 253 254/*************************** Interrupt Services *******************************/ 255static void ahc_clear_intstat(struct ahc_softc *ahc); 256static void ahc_run_qoutfifo(struct ahc_softc *ahc); 257#ifdef AHC_TARGET_MODE 258static void ahc_run_tqinfifo(struct ahc_softc *ahc, int paused); 259#endif 260static void ahc_handle_brkadrint(struct ahc_softc *ahc); 261static void ahc_handle_seqint(struct ahc_softc *ahc, u_int intstat); 262static void ahc_handle_scsiint(struct ahc_softc *ahc, 263 u_int intstat); 264static void ahc_clear_critical_section(struct ahc_softc *ahc); 265 266/***************************** Error Recovery *********************************/ 267static void ahc_freeze_devq(struct ahc_softc *ahc, struct scb *scb); 268static int ahc_abort_scbs(struct ahc_softc *ahc, int target, 269 char channel, int lun, u_int tag, 270 role_t role, uint32_t status); 271static void ahc_calc_residual(struct ahc_softc *ahc, 272 struct scb *scb); 273 274/*********************** Untagged Transaction Routines ************************/ 275static inline void ahc_freeze_untagged_queues(struct ahc_softc *ahc); 276static inline void ahc_release_untagged_queues(struct ahc_softc *ahc); 277 278/* 279 * Block our completion routine from starting the next untagged 280 * transaction for this target or target lun. 281 */ 282static inline void 283ahc_freeze_untagged_queues(struct ahc_softc *ahc) 284{ 285 if ((ahc->flags & AHC_SCB_BTT) == 0) 286 ahc->untagged_queue_lock++; 287} 288 289/* 290 * Allow the next untagged transaction for this target or target lun 291 * to be executed. We use a counting semaphore to allow the lock 292 * to be acquired recursively. Once the count drops to zero, the 293 * transaction queues will be run. 294 */ 295static inline void 296ahc_release_untagged_queues(struct ahc_softc *ahc) 297{ 298 if ((ahc->flags & AHC_SCB_BTT) == 0) { 299 ahc->untagged_queue_lock--; 300 if (ahc->untagged_queue_lock == 0) 301 ahc_run_untagged_queues(ahc); 302 } 303} 304 305/************************* Sequencer Execution Control ************************/ 306/* 307 * Work around any chip bugs related to halting sequencer execution. 308 * On Ultra2 controllers, we must clear the CIOBUS stretch signal by 309 * reading a register that will set this signal and deassert it. 310 * Without this workaround, if the chip is paused, by an interrupt or 311 * manual pause while accessing scb ram, accesses to certain registers 312 * will hang the system (infinite pci retries). 313 */ 314static void 315ahc_pause_bug_fix(struct ahc_softc *ahc) 316{ 317 if ((ahc->features & AHC_ULTRA2) != 0) 318 (void)ahc_inb(ahc, CCSCBCTL); 319} 320 321/* 322 * Determine whether the sequencer has halted code execution. 323 * Returns non-zero status if the sequencer is stopped. 324 */ 325int 326ahc_is_paused(struct ahc_softc *ahc) 327{ 328 return ((ahc_inb(ahc, HCNTRL) & PAUSE) != 0); 329} 330 331/* 332 * Request that the sequencer stop and wait, indefinitely, for it 333 * to stop. The sequencer will only acknowledge that it is paused 334 * once it has reached an instruction boundary and PAUSEDIS is 335 * cleared in the SEQCTL register. The sequencer may use PAUSEDIS 336 * for critical sections. 337 */ 338void 339ahc_pause(struct ahc_softc *ahc) 340{ 341 ahc_outb(ahc, HCNTRL, ahc->pause); 342 343 /* 344 * Since the sequencer can disable pausing in a critical section, we 345 * must loop until it actually stops. 346 */ 347 while (ahc_is_paused(ahc) == 0) 348 ; 349 350 ahc_pause_bug_fix(ahc); 351} 352 353/* 354 * Allow the sequencer to continue program execution. 355 * We check here to ensure that no additional interrupt 356 * sources that would cause the sequencer to halt have been 357 * asserted. If, for example, a SCSI bus reset is detected 358 * while we are fielding a different, pausing, interrupt type, 359 * we don't want to release the sequencer before going back 360 * into our interrupt handler and dealing with this new 361 * condition. 362 */ 363void 364ahc_unpause(struct ahc_softc *ahc) 365{ 366 if ((ahc_inb(ahc, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) == 0) 367 ahc_outb(ahc, HCNTRL, ahc->unpause); 368} 369 370/************************** Memory mapping routines ***************************/ 371static struct ahc_dma_seg * 372ahc_sg_bus_to_virt(struct scb *scb, uint32_t sg_busaddr) 373{ 374 int sg_index; 375 376 sg_index = (sg_busaddr - scb->sg_list_phys)/sizeof(struct ahc_dma_seg); 377 /* sg_list_phys points to entry 1, not 0 */ 378 sg_index++; 379 380 return (&scb->sg_list[sg_index]); 381} 382 383static uint32_t 384ahc_sg_virt_to_bus(struct scb *scb, struct ahc_dma_seg *sg) 385{ 386 int sg_index; 387 388 /* sg_list_phys points to entry 1, not 0 */ 389 sg_index = sg - &scb->sg_list[1]; 390 391 return (scb->sg_list_phys + (sg_index * sizeof(*scb->sg_list))); 392} 393 394static uint32_t 395ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index) 396{ 397 return (ahc->scb_data->hscb_busaddr 398 + (sizeof(struct hardware_scb) * index)); 399} 400 401static void 402ahc_sync_scb(struct ahc_softc *ahc, struct scb *scb, int op) 403{ 404 ahc_dmamap_sync(ahc, ahc->scb_data->hscb_dmat, 405 ahc->scb_data->hscb_dmamap, 406 /*offset*/(scb->hscb - ahc->hscbs) * sizeof(*scb->hscb), 407 /*len*/sizeof(*scb->hscb), op); 408} 409 410void 411ahc_sync_sglist(struct ahc_softc *ahc, struct scb *scb, int op) 412{ 413 if (scb->sg_count == 0) 414 return; 415 416 ahc_dmamap_sync(ahc, ahc->scb_data->sg_dmat, scb->sg_map->sg_dmamap, 417 /*offset*/(scb->sg_list - scb->sg_map->sg_vaddr) 418 * sizeof(struct ahc_dma_seg), 419 /*len*/sizeof(struct ahc_dma_seg) * scb->sg_count, op); 420} 421 422#ifdef AHC_TARGET_MODE 423static uint32_t 424ahc_targetcmd_offset(struct ahc_softc *ahc, u_int index) 425{ 426 return (((uint8_t *)&ahc->targetcmds[index]) - ahc->qoutfifo); 427} 428#endif 429 430/*********************** Miscellaneous Support Functions ***********************/ 431/* 432 * Determine whether the sequencer reported a residual 433 * for this SCB/transaction. 434 */ 435static void 436ahc_update_residual(struct ahc_softc *ahc, struct scb *scb) 437{ 438 uint32_t sgptr; 439 440 sgptr = ahc_le32toh(scb->hscb->sgptr); 441 if ((sgptr & SG_RESID_VALID) != 0) 442 ahc_calc_residual(ahc, scb); 443} 444 445/* 446 * Return pointers to the transfer negotiation information 447 * for the specified our_id/remote_id pair. 448 */ 449struct ahc_initiator_tinfo * 450ahc_fetch_transinfo(struct ahc_softc *ahc, char channel, u_int our_id, 451 u_int remote_id, struct ahc_tmode_tstate **tstate) 452{ 453 /* 454 * Transfer data structures are stored from the perspective 455 * of the target role. Since the parameters for a connection 456 * in the initiator role to a given target are the same as 457 * when the roles are reversed, we pretend we are the target. 458 */ 459 if (channel == 'B') 460 our_id += 8; 461 *tstate = ahc->enabled_targets[our_id]; 462 return (&(*tstate)->transinfo[remote_id]); 463} 464 465uint16_t 466ahc_inw(struct ahc_softc *ahc, u_int port) 467{ 468 uint16_t r = ahc_inb(ahc, port+1) << 8; 469 return r | ahc_inb(ahc, port); 470} 471 472void 473ahc_outw(struct ahc_softc *ahc, u_int port, u_int value) 474{ 475 ahc_outb(ahc, port, value & 0xFF); 476 ahc_outb(ahc, port+1, (value >> 8) & 0xFF); 477} 478 479uint32_t 480ahc_inl(struct ahc_softc *ahc, u_int port) 481{ 482 return ((ahc_inb(ahc, port)) 483 | (ahc_inb(ahc, port+1) << 8) 484 | (ahc_inb(ahc, port+2) << 16) 485 | (ahc_inb(ahc, port+3) << 24)); 486} 487 488void 489ahc_outl(struct ahc_softc *ahc, u_int port, uint32_t value) 490{ 491 ahc_outb(ahc, port, (value) & 0xFF); 492 ahc_outb(ahc, port+1, ((value) >> 8) & 0xFF); 493 ahc_outb(ahc, port+2, ((value) >> 16) & 0xFF); 494 ahc_outb(ahc, port+3, ((value) >> 24) & 0xFF); 495} 496 497uint64_t 498ahc_inq(struct ahc_softc *ahc, u_int port) 499{ 500 return ((ahc_inb(ahc, port)) 501 | (ahc_inb(ahc, port+1) << 8) 502 | (ahc_inb(ahc, port+2) << 16) 503 | (ahc_inb(ahc, port+3) << 24) 504 | (((uint64_t)ahc_inb(ahc, port+4)) << 32) 505 | (((uint64_t)ahc_inb(ahc, port+5)) << 40) 506 | (((uint64_t)ahc_inb(ahc, port+6)) << 48) 507 | (((uint64_t)ahc_inb(ahc, port+7)) << 56)); 508} 509 510void 511ahc_outq(struct ahc_softc *ahc, u_int port, uint64_t value) 512{ 513 ahc_outb(ahc, port, value & 0xFF); 514 ahc_outb(ahc, port+1, (value >> 8) & 0xFF); 515 ahc_outb(ahc, port+2, (value >> 16) & 0xFF); 516 ahc_outb(ahc, port+3, (value >> 24) & 0xFF); 517 ahc_outb(ahc, port+4, (value >> 32) & 0xFF); 518 ahc_outb(ahc, port+5, (value >> 40) & 0xFF); 519 ahc_outb(ahc, port+6, (value >> 48) & 0xFF); 520 ahc_outb(ahc, port+7, (value >> 56) & 0xFF); 521} 522 523/* 524 * Get a free scb. If there are none, see if we can allocate a new SCB. 525 */ 526struct scb * 527ahc_get_scb(struct ahc_softc *ahc) 528{ 529 struct scb *scb; 530 531 if ((scb = SLIST_FIRST(&ahc->scb_data->free_scbs)) == NULL) { 532 ahc_alloc_scbs(ahc); 533 scb = SLIST_FIRST(&ahc->scb_data->free_scbs); 534 if (scb == NULL) 535 return (NULL); 536 } 537 SLIST_REMOVE_HEAD(&ahc->scb_data->free_scbs, links.sle); 538 return (scb); 539} 540 541/* 542 * Return an SCB resource to the free list. 543 */ 544void 545ahc_free_scb(struct ahc_softc *ahc, struct scb *scb) 546{ 547 struct hardware_scb *hscb; 548 549 hscb = scb->hscb; 550 /* Clean up for the next user */ 551 ahc->scb_data->scbindex[hscb->tag] = NULL; 552 scb->flags = SCB_FREE; 553 hscb->control = 0; 554 555 SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, scb, links.sle); 556 557 /* Notify the OSM that a resource is now available. */ 558 ahc_platform_scb_free(ahc, scb); 559} 560 561struct scb * 562ahc_lookup_scb(struct ahc_softc *ahc, u_int tag) 563{ 564 struct scb* scb; 565 566 scb = ahc->scb_data->scbindex[tag]; 567 if (scb != NULL) 568 ahc_sync_scb(ahc, scb, 569 BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE); 570 return (scb); 571} 572 573static void 574ahc_swap_with_next_hscb(struct ahc_softc *ahc, struct scb *scb) 575{ 576 struct hardware_scb *q_hscb; 577 u_int saved_tag; 578 579 /* 580 * Our queuing method is a bit tricky. The card 581 * knows in advance which HSCB to download, and we 582 * can't disappoint it. To achieve this, the next 583 * SCB to download is saved off in ahc->next_queued_scb. 584 * When we are called to queue "an arbitrary scb", 585 * we copy the contents of the incoming HSCB to the one 586 * the sequencer knows about, swap HSCB pointers and 587 * finally assign the SCB to the tag indexed location 588 * in the scb_array. This makes sure that we can still 589 * locate the correct SCB by SCB_TAG. 590 */ 591 q_hscb = ahc->next_queued_scb->hscb; 592 saved_tag = q_hscb->tag; 593 memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb)); 594 if ((scb->flags & SCB_CDB32_PTR) != 0) { 595 q_hscb->shared_data.cdb_ptr = 596 ahc_htole32(ahc_hscb_busaddr(ahc, q_hscb->tag) 597 + offsetof(struct hardware_scb, cdb32)); 598 } 599 q_hscb->tag = saved_tag; 600 q_hscb->next = scb->hscb->tag; 601 602 /* Now swap HSCB pointers. */ 603 ahc->next_queued_scb->hscb = scb->hscb; 604 scb->hscb = q_hscb; 605 606 /* Now define the mapping from tag to SCB in the scbindex */ 607 ahc->scb_data->scbindex[scb->hscb->tag] = scb; 608} 609 610/* 611 * Tell the sequencer about a new transaction to execute. 612 */ 613void 614ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb) 615{ 616 ahc_swap_with_next_hscb(ahc, scb); 617 618 if (scb->hscb->tag == SCB_LIST_NULL 619 || scb->hscb->next == SCB_LIST_NULL) 620 panic("Attempt to queue invalid SCB tag %x:%x\n", 621 scb->hscb->tag, scb->hscb->next); 622 623 /* 624 * Setup data "oddness". 625 */ 626 scb->hscb->lun &= LID; 627 if (ahc_get_transfer_length(scb) & 0x1) 628 scb->hscb->lun |= SCB_XFERLEN_ODD; 629 630 /* 631 * Keep a history of SCBs we've downloaded in the qinfifo. 632 */ 633 ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag; 634 635 /* 636 * Make sure our data is consistent from the 637 * perspective of the adapter. 638 */ 639 ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); 640 641 /* Tell the adapter about the newly queued SCB */ 642 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 643 ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); 644 } else { 645 if ((ahc->features & AHC_AUTOPAUSE) == 0) 646 ahc_pause(ahc); 647 ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); 648 if ((ahc->features & AHC_AUTOPAUSE) == 0) 649 ahc_unpause(ahc); 650 } 651} 652 653struct scsi_sense_data * 654ahc_get_sense_buf(struct ahc_softc *ahc, struct scb *scb) 655{ 656 int offset; 657 658 offset = scb - ahc->scb_data->scbarray; 659 return (&ahc->scb_data->sense[offset]); 660} 661 662static uint32_t 663ahc_get_sense_bufaddr(struct ahc_softc *ahc, struct scb *scb) 664{ 665 int offset; 666 667 offset = scb - ahc->scb_data->scbarray; 668 return (ahc->scb_data->sense_busaddr 669 + (offset * sizeof(struct scsi_sense_data))); 670} 671 672/************************** Interrupt Processing ******************************/ 673static void 674ahc_sync_qoutfifo(struct ahc_softc *ahc, int op) 675{ 676 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, 677 /*offset*/0, /*len*/256, op); 678} 679 680static void 681ahc_sync_tqinfifo(struct ahc_softc *ahc, int op) 682{ 683#ifdef AHC_TARGET_MODE 684 if ((ahc->flags & AHC_TARGETROLE) != 0) { 685 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, 686 ahc->shared_data_dmamap, 687 ahc_targetcmd_offset(ahc, 0), 688 sizeof(struct target_cmd) * AHC_TMODE_CMDS, 689 op); 690 } 691#endif 692} 693 694/* 695 * See if the firmware has posted any completed commands 696 * into our in-core command complete fifos. 697 */ 698#define AHC_RUN_QOUTFIFO 0x1 699#define AHC_RUN_TQINFIFO 0x2 700static u_int 701ahc_check_cmdcmpltqueues(struct ahc_softc *ahc) 702{ 703 u_int retval; 704 705 retval = 0; 706 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, 707 /*offset*/ahc->qoutfifonext, /*len*/1, 708 BUS_DMASYNC_POSTREAD); 709 if (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL) 710 retval |= AHC_RUN_QOUTFIFO; 711#ifdef AHC_TARGET_MODE 712 if ((ahc->flags & AHC_TARGETROLE) != 0 713 && (ahc->flags & AHC_TQINFIFO_BLOCKED) == 0) { 714 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, 715 ahc->shared_data_dmamap, 716 ahc_targetcmd_offset(ahc, ahc->tqinfifofnext), 717 /*len*/sizeof(struct target_cmd), 718 BUS_DMASYNC_POSTREAD); 719 if (ahc->targetcmds[ahc->tqinfifonext].cmd_valid != 0) 720 retval |= AHC_RUN_TQINFIFO; 721 } 722#endif 723 return (retval); 724} 725 726/* 727 * Catch an interrupt from the adapter 728 */ 729int 730ahc_intr(struct ahc_softc *ahc) 731{ 732 u_int intstat; 733 734 if ((ahc->pause & INTEN) == 0) { 735 /* 736 * Our interrupt is not enabled on the chip 737 * and may be disabled for re-entrancy reasons, 738 * so just return. This is likely just a shared 739 * interrupt. 740 */ 741 return (0); 742 } 743 /* 744 * Instead of directly reading the interrupt status register, 745 * infer the cause of the interrupt by checking our in-core 746 * completion queues. This avoids a costly PCI bus read in 747 * most cases. 748 */ 749 if ((ahc->flags & (AHC_ALL_INTERRUPTS|AHC_EDGE_INTERRUPT)) == 0 750 && (ahc_check_cmdcmpltqueues(ahc) != 0)) 751 intstat = CMDCMPLT; 752 else { 753 intstat = ahc_inb(ahc, INTSTAT); 754 } 755 756 if ((intstat & INT_PEND) == 0) { 757#if AHC_PCI_CONFIG > 0 758 if (ahc->unsolicited_ints > 500) { 759 ahc->unsolicited_ints = 0; 760 if ((ahc->chip & AHC_PCI) != 0 761 && (ahc_inb(ahc, ERROR) & PCIERRSTAT) != 0) 762 ahc->bus_intr(ahc); 763 } 764#endif 765 ahc->unsolicited_ints++; 766 return (0); 767 } 768 ahc->unsolicited_ints = 0; 769 770 if (intstat & CMDCMPLT) { 771 ahc_outb(ahc, CLRINT, CLRCMDINT); 772 773 /* 774 * Ensure that the chip sees that we've cleared 775 * this interrupt before we walk the output fifo. 776 * Otherwise, we may, due to posted bus writes, 777 * clear the interrupt after we finish the scan, 778 * and after the sequencer has added new entries 779 * and asserted the interrupt again. 780 */ 781 ahc_flush_device_writes(ahc); 782 ahc_run_qoutfifo(ahc); 783#ifdef AHC_TARGET_MODE 784 if ((ahc->flags & AHC_TARGETROLE) != 0) 785 ahc_run_tqinfifo(ahc, /*paused*/FALSE); 786#endif 787 } 788 789 /* 790 * Handle statuses that may invalidate our cached 791 * copy of INTSTAT separately. 792 */ 793 if (intstat == 0xFF && (ahc->features & AHC_REMOVABLE) != 0) { 794 /* Hot eject. Do nothing */ 795 } else if (intstat & BRKADRINT) { 796 ahc_handle_brkadrint(ahc); 797 } else if ((intstat & (SEQINT|SCSIINT)) != 0) { 798 799 ahc_pause_bug_fix(ahc); 800 801 if ((intstat & SEQINT) != 0) 802 ahc_handle_seqint(ahc, intstat); 803 804 if ((intstat & SCSIINT) != 0) 805 ahc_handle_scsiint(ahc, intstat); 806 } 807 return (1); 808} 809 810/************************* Sequencer Execution Control ************************/ 811/* 812 * Restart the sequencer program from address zero 813 */ 814static void 815ahc_restart(struct ahc_softc *ahc) 816{ 817 uint8_t sblkctl; 818 819 ahc_pause(ahc); 820 821 /* No more pending messages. */ 822 ahc_clear_msg_state(ahc); 823 824 ahc_outb(ahc, SCSISIGO, 0); /* De-assert BSY */ 825 ahc_outb(ahc, MSG_OUT, MSG_NOOP); /* No message to send */ 826 ahc_outb(ahc, SXFRCTL1, ahc_inb(ahc, SXFRCTL1) & ~BITBUCKET); 827 ahc_outb(ahc, LASTPHASE, P_BUSFREE); 828 ahc_outb(ahc, SAVED_SCSIID, 0xFF); 829 ahc_outb(ahc, SAVED_LUN, 0xFF); 830 831 /* 832 * Ensure that the sequencer's idea of TQINPOS 833 * matches our own. The sequencer increments TQINPOS 834 * only after it sees a DMA complete and a reset could 835 * occur before the increment leaving the kernel to believe 836 * the command arrived but the sequencer to not. 837 */ 838 ahc_outb(ahc, TQINPOS, ahc->tqinfifonext); 839 840 /* Always allow reselection */ 841 ahc_outb(ahc, SCSISEQ, 842 ahc_inb(ahc, SCSISEQ_TEMPLATE) & (ENSELI|ENRSELI|ENAUTOATNP)); 843 if ((ahc->features & AHC_CMD_CHAN) != 0) { 844 /* Ensure that no DMA operations are in progress */ 845 ahc_outb(ahc, CCSCBCNT, 0); 846 ahc_outb(ahc, CCSGCTL, 0); 847 ahc_outb(ahc, CCSCBCTL, 0); 848 } 849 /* 850 * If we were in the process of DMA'ing SCB data into 851 * an SCB, replace that SCB on the free list. This prevents 852 * an SCB leak. 853 */ 854 if ((ahc_inb(ahc, SEQ_FLAGS2) & SCB_DMA) != 0) { 855 ahc_add_curscb_to_free_list(ahc); 856 ahc_outb(ahc, SEQ_FLAGS2, 857 ahc_inb(ahc, SEQ_FLAGS2) & ~SCB_DMA); 858 } 859 860 /* 861 * Clear any pending sequencer interrupt. It is no 862 * longer relevant since we're resetting the Program 863 * Counter. 864 */ 865 ahc_outb(ahc, CLRINT, CLRSEQINT); 866 867 ahc_outb(ahc, MWI_RESIDUAL, 0); 868 ahc_outb(ahc, SEQCTL, ahc->seqctl); 869 ahc_outb(ahc, SEQADDR0, 0); 870 ahc_outb(ahc, SEQADDR1, 0); 871 872 /* 873 * Take the LED out of diagnostic mode on PM resume, too 874 */ 875 sblkctl = ahc_inb(ahc, SBLKCTL); 876 ahc_outb(ahc, SBLKCTL, (sblkctl & ~(DIAGLEDEN|DIAGLEDON))); 877 878 ahc_unpause(ahc); 879} 880 881/************************* Input/Output Queues ********************************/ 882static void 883ahc_run_qoutfifo(struct ahc_softc *ahc) 884{ 885 struct scb *scb; 886 u_int scb_index; 887 888 ahc_sync_qoutfifo(ahc, BUS_DMASYNC_POSTREAD); 889 while (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL) { 890 891 scb_index = ahc->qoutfifo[ahc->qoutfifonext]; 892 if ((ahc->qoutfifonext & 0x03) == 0x03) { 893 u_int modnext; 894 895 /* 896 * Clear 32bits of QOUTFIFO at a time 897 * so that we don't clobber an incoming 898 * byte DMA to the array on architectures 899 * that only support 32bit load and store 900 * operations. 901 */ 902 modnext = ahc->qoutfifonext & ~0x3; 903 *((uint32_t *)(&ahc->qoutfifo[modnext])) = 0xFFFFFFFFUL; 904 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, 905 ahc->shared_data_dmamap, 906 /*offset*/modnext, /*len*/4, 907 BUS_DMASYNC_PREREAD); 908 } 909 ahc->qoutfifonext++; 910 911 scb = ahc_lookup_scb(ahc, scb_index); 912 if (scb == NULL) { 913 printk("%s: WARNING no command for scb %d " 914 "(cmdcmplt)\nQOUTPOS = %d\n", 915 ahc_name(ahc), scb_index, 916 (ahc->qoutfifonext - 1) & 0xFF); 917 continue; 918 } 919 920 /* 921 * Save off the residual 922 * if there is one. 923 */ 924 ahc_update_residual(ahc, scb); 925 ahc_done(ahc, scb); 926 } 927} 928 929static void 930ahc_run_untagged_queues(struct ahc_softc *ahc) 931{ 932 int i; 933 934 for (i = 0; i < 16; i++) 935 ahc_run_untagged_queue(ahc, &ahc->untagged_queues[i]); 936} 937 938static void 939ahc_run_untagged_queue(struct ahc_softc *ahc, struct scb_tailq *queue) 940{ 941 struct scb *scb; 942 943 if (ahc->untagged_queue_lock != 0) 944 return; 945 946 if ((scb = TAILQ_FIRST(queue)) != NULL 947 && (scb->flags & SCB_ACTIVE) == 0) { 948 scb->flags |= SCB_ACTIVE; 949 ahc_queue_scb(ahc, scb); 950 } 951} 952 953/************************* Interrupt Handling *********************************/ 954static void 955ahc_handle_brkadrint(struct ahc_softc *ahc) 956{ 957 /* 958 * We upset the sequencer :-( 959 * Lookup the error message 960 */ 961 int i; 962 int error; 963 964 error = ahc_inb(ahc, ERROR); 965 for (i = 0; error != 1 && i < num_errors; i++) 966 error >>= 1; 967 printk("%s: brkadrint, %s at seqaddr = 0x%x\n", 968 ahc_name(ahc), ahc_hard_errors[i].errmesg, 969 ahc_inb(ahc, SEQADDR0) | 970 (ahc_inb(ahc, SEQADDR1) << 8)); 971 972 ahc_dump_card_state(ahc); 973 974 /* Tell everyone that this HBA is no longer available */ 975 ahc_abort_scbs(ahc, CAM_TARGET_WILDCARD, ALL_CHANNELS, 976 CAM_LUN_WILDCARD, SCB_LIST_NULL, ROLE_UNKNOWN, 977 CAM_NO_HBA); 978 979 /* Disable all interrupt sources by resetting the controller */ 980 ahc_shutdown(ahc); 981} 982 983static void 984ahc_handle_seqint(struct ahc_softc *ahc, u_int intstat) 985{ 986 struct scb *scb; 987 struct ahc_devinfo devinfo; 988 989 ahc_fetch_devinfo(ahc, &devinfo); 990 991 /* 992 * Clear the upper byte that holds SEQINT status 993 * codes and clear the SEQINT bit. We will unpause 994 * the sequencer, if appropriate, after servicing 995 * the request. 996 */ 997 ahc_outb(ahc, CLRINT, CLRSEQINT); 998 switch (intstat & SEQINT_MASK) { 999 case BAD_STATUS: 1000 { 1001 u_int scb_index; 1002 struct hardware_scb *hscb; 1003 1004 /* 1005 * Set the default return value to 0 (don't 1006 * send sense). The sense code will change 1007 * this if needed. 1008 */ 1009 ahc_outb(ahc, RETURN_1, 0); 1010 1011 /* 1012 * The sequencer will notify us when a command 1013 * has an error that would be of interest to 1014 * the kernel. This allows us to leave the sequencer 1015 * running in the common case of command completes 1016 * without error. The sequencer will already have 1017 * dma'd the SCB back up to us, so we can reference 1018 * the in kernel copy directly. 1019 */ 1020 scb_index = ahc_inb(ahc, SCB_TAG); 1021 scb = ahc_lookup_scb(ahc, scb_index); 1022 if (scb == NULL) { 1023 ahc_print_devinfo(ahc, &devinfo); 1024 printk("ahc_intr - referenced scb " 1025 "not valid during seqint 0x%x scb(%d)\n", 1026 intstat, scb_index); 1027 ahc_dump_card_state(ahc); 1028 panic("for safety"); 1029 goto unpause; 1030 } 1031 1032 hscb = scb->hscb; 1033 1034 /* Don't want to clobber the original sense code */ 1035 if ((scb->flags & SCB_SENSE) != 0) { 1036 /* 1037 * Clear the SCB_SENSE Flag and have 1038 * the sequencer do a normal command 1039 * complete. 1040 */ 1041 scb->flags &= ~SCB_SENSE; 1042 ahc_set_transaction_status(scb, CAM_AUTOSENSE_FAIL); 1043 break; 1044 } 1045 ahc_set_transaction_status(scb, CAM_SCSI_STATUS_ERROR); 1046 /* Freeze the queue until the client sees the error. */ 1047 ahc_freeze_devq(ahc, scb); 1048 ahc_freeze_scb(scb); 1049 ahc_set_scsi_status(scb, hscb->shared_data.status.scsi_status); 1050 switch (hscb->shared_data.status.scsi_status) { 1051 case SCSI_STATUS_OK: 1052 printk("%s: Interrupted for status of 0???\n", 1053 ahc_name(ahc)); 1054 break; 1055 case SCSI_STATUS_CMD_TERMINATED: 1056 case SCSI_STATUS_CHECK_COND: 1057 { 1058 struct ahc_dma_seg *sg; 1059 struct scsi_sense *sc; 1060 struct ahc_initiator_tinfo *targ_info; 1061 struct ahc_tmode_tstate *tstate; 1062 struct ahc_transinfo *tinfo; 1063#ifdef AHC_DEBUG 1064 if (ahc_debug & AHC_SHOW_SENSE) { 1065 ahc_print_path(ahc, scb); 1066 printk("SCB %d: requests Check Status\n", 1067 scb->hscb->tag); 1068 } 1069#endif 1070 1071 if (ahc_perform_autosense(scb) == 0) 1072 break; 1073 1074 targ_info = ahc_fetch_transinfo(ahc, 1075 devinfo.channel, 1076 devinfo.our_scsiid, 1077 devinfo.target, 1078 &tstate); 1079 tinfo = &targ_info->curr; 1080 sg = scb->sg_list; 1081 sc = (struct scsi_sense *)(&hscb->shared_data.cdb); 1082 /* 1083 * Save off the residual if there is one. 1084 */ 1085 ahc_update_residual(ahc, scb); 1086#ifdef AHC_DEBUG 1087 if (ahc_debug & AHC_SHOW_SENSE) { 1088 ahc_print_path(ahc, scb); 1089 printk("Sending Sense\n"); 1090 } 1091#endif 1092 sg->addr = ahc_get_sense_bufaddr(ahc, scb); 1093 sg->len = ahc_get_sense_bufsize(ahc, scb); 1094 sg->len |= AHC_DMA_LAST_SEG; 1095 1096 /* Fixup byte order */ 1097 sg->addr = ahc_htole32(sg->addr); 1098 sg->len = ahc_htole32(sg->len); 1099 1100 sc->opcode = REQUEST_SENSE; 1101 sc->byte2 = 0; 1102 if (tinfo->protocol_version <= SCSI_REV_2 1103 && SCB_GET_LUN(scb) < 8) 1104 sc->byte2 = SCB_GET_LUN(scb) << 5; 1105 sc->unused[0] = 0; 1106 sc->unused[1] = 0; 1107 sc->length = sg->len; 1108 sc->control = 0; 1109 1110 /* 1111 * We can't allow the target to disconnect. 1112 * This will be an untagged transaction and 1113 * having the target disconnect will make this 1114 * transaction indestinguishable from outstanding 1115 * tagged transactions. 1116 */ 1117 hscb->control = 0; 1118 1119 /* 1120 * This request sense could be because the 1121 * the device lost power or in some other 1122 * way has lost our transfer negotiations. 1123 * Renegotiate if appropriate. Unit attention 1124 * errors will be reported before any data 1125 * phases occur. 1126 */ 1127 if (ahc_get_residual(scb) 1128 == ahc_get_transfer_length(scb)) { 1129 ahc_update_neg_request(ahc, &devinfo, 1130 tstate, targ_info, 1131 AHC_NEG_IF_NON_ASYNC); 1132 } 1133 if (tstate->auto_negotiate & devinfo.target_mask) { 1134 hscb->control |= MK_MESSAGE; 1135 scb->flags &= ~SCB_NEGOTIATE; 1136 scb->flags |= SCB_AUTO_NEGOTIATE; 1137 } 1138 hscb->cdb_len = sizeof(*sc); 1139 hscb->dataptr = sg->addr; 1140 hscb->datacnt = sg->len; 1141 hscb->sgptr = scb->sg_list_phys | SG_FULL_RESID; 1142 hscb->sgptr = ahc_htole32(hscb->sgptr); 1143 scb->sg_count = 1; 1144 scb->flags |= SCB_SENSE; 1145 ahc_qinfifo_requeue_tail(ahc, scb); 1146 ahc_outb(ahc, RETURN_1, SEND_SENSE); 1147 /* 1148 * Ensure we have enough time to actually 1149 * retrieve the sense. 1150 */ 1151 ahc_scb_timer_reset(scb, 5 * 1000000); 1152 break; 1153 } 1154 default: 1155 break; 1156 } 1157 break; 1158 } 1159 case NO_MATCH: 1160 { 1161 /* Ensure we don't leave the selection hardware on */ 1162 ahc_outb(ahc, SCSISEQ, 1163 ahc_inb(ahc, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP)); 1164 1165 printk("%s:%c:%d: no active SCB for reconnecting " 1166 "target - issuing BUS DEVICE RESET\n", 1167 ahc_name(ahc), devinfo.channel, devinfo.target); 1168 printk("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, " 1169 "ARG_1 == 0x%x ACCUM = 0x%x\n", 1170 ahc_inb(ahc, SAVED_SCSIID), ahc_inb(ahc, SAVED_LUN), 1171 ahc_inb(ahc, ARG_1), ahc_inb(ahc, ACCUM)); 1172 printk("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, " 1173 "SINDEX == 0x%x\n", 1174 ahc_inb(ahc, SEQ_FLAGS), ahc_inb(ahc, SCBPTR), 1175 ahc_index_busy_tcl(ahc, 1176 BUILD_TCL(ahc_inb(ahc, SAVED_SCSIID), 1177 ahc_inb(ahc, SAVED_LUN))), 1178 ahc_inb(ahc, SINDEX)); 1179 printk("SCSIID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, " 1180 "SCB_TAG == 0x%x, SCB_CONTROL == 0x%x\n", 1181 ahc_inb(ahc, SCSIID), ahc_inb(ahc, SCB_SCSIID), 1182 ahc_inb(ahc, SCB_LUN), ahc_inb(ahc, SCB_TAG), 1183 ahc_inb(ahc, SCB_CONTROL)); 1184 printk("SCSIBUSL == 0x%x, SCSISIGI == 0x%x\n", 1185 ahc_inb(ahc, SCSIBUSL), ahc_inb(ahc, SCSISIGI)); 1186 printk("SXFRCTL0 == 0x%x\n", ahc_inb(ahc, SXFRCTL0)); 1187 printk("SEQCTL == 0x%x\n", ahc_inb(ahc, SEQCTL)); 1188 ahc_dump_card_state(ahc); 1189 ahc->msgout_buf[0] = MSG_BUS_DEV_RESET; 1190 ahc->msgout_len = 1; 1191 ahc->msgout_index = 0; 1192 ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; 1193 ahc_outb(ahc, MSG_OUT, HOST_MSG); 1194 ahc_assert_atn(ahc); 1195 break; 1196 } 1197 case SEND_REJECT: 1198 { 1199 u_int rejbyte = ahc_inb(ahc, ACCUM); 1200 printk("%s:%c:%d: Warning - unknown message received from " 1201 "target (0x%x). Rejecting\n", 1202 ahc_name(ahc), devinfo.channel, devinfo.target, rejbyte); 1203 break; 1204 } 1205 case PROTO_VIOLATION: 1206 { 1207 ahc_handle_proto_violation(ahc); 1208 break; 1209 } 1210 case IGN_WIDE_RES: 1211 ahc_handle_ign_wide_residue(ahc, &devinfo); 1212 break; 1213 case PDATA_REINIT: 1214 ahc_reinitialize_dataptrs(ahc); 1215 break; 1216 case BAD_PHASE: 1217 { 1218 u_int lastphase; 1219 1220 lastphase = ahc_inb(ahc, LASTPHASE); 1221 printk("%s:%c:%d: unknown scsi bus phase %x, " 1222 "lastphase = 0x%x. Attempting to continue\n", 1223 ahc_name(ahc), devinfo.channel, devinfo.target, 1224 lastphase, ahc_inb(ahc, SCSISIGI)); 1225 break; 1226 } 1227 case MISSED_BUSFREE: 1228 { 1229 u_int lastphase; 1230 1231 lastphase = ahc_inb(ahc, LASTPHASE); 1232 printk("%s:%c:%d: Missed busfree. " 1233 "Lastphase = 0x%x, Curphase = 0x%x\n", 1234 ahc_name(ahc), devinfo.channel, devinfo.target, 1235 lastphase, ahc_inb(ahc, SCSISIGI)); 1236 ahc_restart(ahc); 1237 return; 1238 } 1239 case HOST_MSG_LOOP: 1240 { 1241 /* 1242 * The sequencer has encountered a message phase 1243 * that requires host assistance for completion. 1244 * While handling the message phase(s), we will be 1245 * notified by the sequencer after each byte is 1246 * transferred so we can track bus phase changes. 1247 * 1248 * If this is the first time we've seen a HOST_MSG_LOOP 1249 * interrupt, initialize the state of the host message 1250 * loop. 1251 */ 1252 if (ahc->msg_type == MSG_TYPE_NONE) { 1253 struct scb *scb; 1254 u_int scb_index; 1255 u_int bus_phase; 1256 1257 bus_phase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; 1258 if (bus_phase != P_MESGIN 1259 && bus_phase != P_MESGOUT) { 1260 printk("ahc_intr: HOST_MSG_LOOP bad " 1261 "phase 0x%x\n", 1262 bus_phase); 1263 /* 1264 * Probably transitioned to bus free before 1265 * we got here. Just punt the message. 1266 */ 1267 ahc_clear_intstat(ahc); 1268 ahc_restart(ahc); 1269 return; 1270 } 1271 1272 scb_index = ahc_inb(ahc, SCB_TAG); 1273 scb = ahc_lookup_scb(ahc, scb_index); 1274 if (devinfo.role == ROLE_INITIATOR) { 1275 if (bus_phase == P_MESGOUT) { 1276 if (scb == NULL) 1277 panic("HOST_MSG_LOOP with " 1278 "invalid SCB %x\n", 1279 scb_index); 1280 1281 ahc_setup_initiator_msgout(ahc, 1282 &devinfo, 1283 scb); 1284 } else { 1285 ahc->msg_type = 1286 MSG_TYPE_INITIATOR_MSGIN; 1287 ahc->msgin_index = 0; 1288 } 1289 } 1290#ifdef AHC_TARGET_MODE 1291 else { 1292 if (bus_phase == P_MESGOUT) { 1293 ahc->msg_type = 1294 MSG_TYPE_TARGET_MSGOUT; 1295 ahc->msgin_index = 0; 1296 } 1297 else 1298 ahc_setup_target_msgin(ahc, 1299 &devinfo, 1300 scb); 1301 } 1302#endif 1303 } 1304 1305 ahc_handle_message_phase(ahc); 1306 break; 1307 } 1308 case PERR_DETECTED: 1309 { 1310 /* 1311 * If we've cleared the parity error interrupt 1312 * but the sequencer still believes that SCSIPERR 1313 * is true, it must be that the parity error is 1314 * for the currently presented byte on the bus, 1315 * and we are not in a phase (data-in) where we will 1316 * eventually ack this byte. Ack the byte and 1317 * throw it away in the hope that the target will 1318 * take us to message out to deliver the appropriate 1319 * error message. 1320 */ 1321 if ((intstat & SCSIINT) == 0 1322 && (ahc_inb(ahc, SSTAT1) & SCSIPERR) != 0) { 1323 1324 if ((ahc->features & AHC_DT) == 0) { 1325 u_int curphase; 1326 1327 /* 1328 * The hardware will only let you ack bytes 1329 * if the expected phase in SCSISIGO matches 1330 * the current phase. Make sure this is 1331 * currently the case. 1332 */ 1333 curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; 1334 ahc_outb(ahc, LASTPHASE, curphase); 1335 ahc_outb(ahc, SCSISIGO, curphase); 1336 } 1337 if ((ahc_inb(ahc, SCSISIGI) & (CDI|MSGI)) == 0) { 1338 int wait; 1339 1340 /* 1341 * In a data phase. Faster to bitbucket 1342 * the data than to individually ack each 1343 * byte. This is also the only strategy 1344 * that will work with AUTOACK enabled. 1345 */ 1346 ahc_outb(ahc, SXFRCTL1, 1347 ahc_inb(ahc, SXFRCTL1) | BITBUCKET); 1348 wait = 5000; 1349 while (--wait != 0) { 1350 if ((ahc_inb(ahc, SCSISIGI) 1351 & (CDI|MSGI)) != 0) 1352 break; 1353 ahc_delay(100); 1354 } 1355 ahc_outb(ahc, SXFRCTL1, 1356 ahc_inb(ahc, SXFRCTL1) & ~BITBUCKET); 1357 if (wait == 0) { 1358 struct scb *scb; 1359 u_int scb_index; 1360 1361 ahc_print_devinfo(ahc, &devinfo); 1362 printk("Unable to clear parity error. " 1363 "Resetting bus.\n"); 1364 scb_index = ahc_inb(ahc, SCB_TAG); 1365 scb = ahc_lookup_scb(ahc, scb_index); 1366 if (scb != NULL) 1367 ahc_set_transaction_status(scb, 1368 CAM_UNCOR_PARITY); 1369 ahc_reset_channel(ahc, devinfo.channel, 1370 /*init reset*/TRUE); 1371 } 1372 } else { 1373 ahc_inb(ahc, SCSIDATL); 1374 } 1375 } 1376 break; 1377 } 1378 case DATA_OVERRUN: 1379 { 1380 /* 1381 * When the sequencer detects an overrun, it 1382 * places the controller in "BITBUCKET" mode 1383 * and allows the target to complete its transfer. 1384 * Unfortunately, none of the counters get updated 1385 * when the controller is in this mode, so we have 1386 * no way of knowing how large the overrun was. 1387 */ 1388 u_int scbindex = ahc_inb(ahc, SCB_TAG); 1389 u_int lastphase = ahc_inb(ahc, LASTPHASE); 1390 u_int i; 1391 1392 scb = ahc_lookup_scb(ahc, scbindex); 1393 for (i = 0; i < num_phases; i++) { 1394 if (lastphase == ahc_phase_table[i].phase) 1395 break; 1396 } 1397 ahc_print_path(ahc, scb); 1398 printk("data overrun detected %s." 1399 " Tag == 0x%x.\n", 1400 ahc_phase_table[i].phasemsg, 1401 scb->hscb->tag); 1402 ahc_print_path(ahc, scb); 1403 printk("%s seen Data Phase. Length = %ld. NumSGs = %d.\n", 1404 ahc_inb(ahc, SEQ_FLAGS) & DPHASE ? "Have" : "Haven't", 1405 ahc_get_transfer_length(scb), scb->sg_count); 1406 if (scb->sg_count > 0) { 1407 for (i = 0; i < scb->sg_count; i++) { 1408 1409 printk("sg[%d] - Addr 0x%x%x : Length %d\n", 1410 i, 1411 (ahc_le32toh(scb->sg_list[i].len) >> 24 1412 & SG_HIGH_ADDR_BITS), 1413 ahc_le32toh(scb->sg_list[i].addr), 1414 ahc_le32toh(scb->sg_list[i].len) 1415 & AHC_SG_LEN_MASK); 1416 } 1417 } 1418 /* 1419 * Set this and it will take effect when the 1420 * target does a command complete. 1421 */ 1422 ahc_freeze_devq(ahc, scb); 1423 if ((scb->flags & SCB_SENSE) == 0) { 1424 ahc_set_transaction_status(scb, CAM_DATA_RUN_ERR); 1425 } else { 1426 scb->flags &= ~SCB_SENSE; 1427 ahc_set_transaction_status(scb, CAM_AUTOSENSE_FAIL); 1428 } 1429 ahc_freeze_scb(scb); 1430 1431 if ((ahc->features & AHC_ULTRA2) != 0) { 1432 /* 1433 * Clear the channel in case we return 1434 * to data phase later. 1435 */ 1436 ahc_outb(ahc, SXFRCTL0, 1437 ahc_inb(ahc, SXFRCTL0) | CLRSTCNT|CLRCHN); 1438 ahc_outb(ahc, SXFRCTL0, 1439 ahc_inb(ahc, SXFRCTL0) | CLRSTCNT|CLRCHN); 1440 } 1441 if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { 1442 u_int dscommand1; 1443 1444 /* Ensure HHADDR is 0 for future DMA operations. */ 1445 dscommand1 = ahc_inb(ahc, DSCOMMAND1); 1446 ahc_outb(ahc, DSCOMMAND1, dscommand1 | HADDLDSEL0); 1447 ahc_outb(ahc, HADDR, 0); 1448 ahc_outb(ahc, DSCOMMAND1, dscommand1); 1449 } 1450 break; 1451 } 1452 case MKMSG_FAILED: 1453 { 1454 u_int scbindex; 1455 1456 printk("%s:%c:%d:%d: Attempt to issue message failed\n", 1457 ahc_name(ahc), devinfo.channel, devinfo.target, 1458 devinfo.lun); 1459 scbindex = ahc_inb(ahc, SCB_TAG); 1460 scb = ahc_lookup_scb(ahc, scbindex); 1461 if (scb != NULL 1462 && (scb->flags & SCB_RECOVERY_SCB) != 0) 1463 /* 1464 * Ensure that we didn't put a second instance of this 1465 * SCB into the QINFIFO. 1466 */ 1467 ahc_search_qinfifo(ahc, SCB_GET_TARGET(ahc, scb), 1468 SCB_GET_CHANNEL(ahc, scb), 1469 SCB_GET_LUN(scb), scb->hscb->tag, 1470 ROLE_INITIATOR, /*status*/0, 1471 SEARCH_REMOVE); 1472 break; 1473 } 1474 case NO_FREE_SCB: 1475 { 1476 printk("%s: No free or disconnected SCBs\n", ahc_name(ahc)); 1477 ahc_dump_card_state(ahc); 1478 panic("for safety"); 1479 break; 1480 } 1481 case SCB_MISMATCH: 1482 { 1483 u_int scbptr; 1484 1485 scbptr = ahc_inb(ahc, SCBPTR); 1486 printk("Bogus TAG after DMA. SCBPTR %d, tag %d, our tag %d\n", 1487 scbptr, ahc_inb(ahc, ARG_1), 1488 ahc->scb_data->hscbs[scbptr].tag); 1489 ahc_dump_card_state(ahc); 1490 panic("for safety"); 1491 break; 1492 } 1493 case OUT_OF_RANGE: 1494 { 1495 printk("%s: BTT calculation out of range\n", ahc_name(ahc)); 1496 printk("SAVED_SCSIID == 0x%x, SAVED_LUN == 0x%x, " 1497 "ARG_1 == 0x%x ACCUM = 0x%x\n", 1498 ahc_inb(ahc, SAVED_SCSIID), ahc_inb(ahc, SAVED_LUN), 1499 ahc_inb(ahc, ARG_1), ahc_inb(ahc, ACCUM)); 1500 printk("SEQ_FLAGS == 0x%x, SCBPTR == 0x%x, BTT == 0x%x, " 1501 "SINDEX == 0x%x\n, A == 0x%x\n", 1502 ahc_inb(ahc, SEQ_FLAGS), ahc_inb(ahc, SCBPTR), 1503 ahc_index_busy_tcl(ahc, 1504 BUILD_TCL(ahc_inb(ahc, SAVED_SCSIID), 1505 ahc_inb(ahc, SAVED_LUN))), 1506 ahc_inb(ahc, SINDEX), 1507 ahc_inb(ahc, ACCUM)); 1508 printk("SCSIID == 0x%x, SCB_SCSIID == 0x%x, SCB_LUN == 0x%x, " 1509 "SCB_TAG == 0x%x, SCB_CONTROL == 0x%x\n", 1510 ahc_inb(ahc, SCSIID), ahc_inb(ahc, SCB_SCSIID), 1511 ahc_inb(ahc, SCB_LUN), ahc_inb(ahc, SCB_TAG), 1512 ahc_inb(ahc, SCB_CONTROL)); 1513 printk("SCSIBUSL == 0x%x, SCSISIGI == 0x%x\n", 1514 ahc_inb(ahc, SCSIBUSL), ahc_inb(ahc, SCSISIGI)); 1515 ahc_dump_card_state(ahc); 1516 panic("for safety"); 1517 break; 1518 } 1519 default: 1520 printk("ahc_intr: seqint, " 1521 "intstat == 0x%x, scsisigi = 0x%x\n", 1522 intstat, ahc_inb(ahc, SCSISIGI)); 1523 break; 1524 } 1525unpause: 1526 /* 1527 * The sequencer is paused immediately on 1528 * a SEQINT, so we should restart it when 1529 * we're done. 1530 */ 1531 ahc_unpause(ahc); 1532} 1533 1534static void 1535ahc_handle_scsiint(struct ahc_softc *ahc, u_int intstat) 1536{ 1537 u_int scb_index; 1538 u_int status0; 1539 u_int status; 1540 struct scb *scb; 1541 char cur_channel; 1542 char intr_channel; 1543 1544 if ((ahc->features & AHC_TWIN) != 0 1545 && ((ahc_inb(ahc, SBLKCTL) & SELBUSB) != 0)) 1546 cur_channel = 'B'; 1547 else 1548 cur_channel = 'A'; 1549 intr_channel = cur_channel; 1550 1551 if ((ahc->features & AHC_ULTRA2) != 0) 1552 status0 = ahc_inb(ahc, SSTAT0) & IOERR; 1553 else 1554 status0 = 0; 1555 status = ahc_inb(ahc, SSTAT1) & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR); 1556 if (status == 0 && status0 == 0) { 1557 if ((ahc->features & AHC_TWIN) != 0) { 1558 /* Try the other channel */ 1559 ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) ^ SELBUSB); 1560 status = ahc_inb(ahc, SSTAT1) 1561 & (SELTO|SCSIRSTI|BUSFREE|SCSIPERR); 1562 intr_channel = (cur_channel == 'A') ? 'B' : 'A'; 1563 } 1564 if (status == 0) { 1565 printk("%s: Spurious SCSI interrupt\n", ahc_name(ahc)); 1566 ahc_outb(ahc, CLRINT, CLRSCSIINT); 1567 ahc_unpause(ahc); 1568 return; 1569 } 1570 } 1571 1572 /* Make sure the sequencer is in a safe location. */ 1573 ahc_clear_critical_section(ahc); 1574 1575 scb_index = ahc_inb(ahc, SCB_TAG); 1576 scb = ahc_lookup_scb(ahc, scb_index); 1577 if (scb != NULL 1578 && (ahc_inb(ahc, SEQ_FLAGS) & NOT_IDENTIFIED) != 0) 1579 scb = NULL; 1580 1581 if ((ahc->features & AHC_ULTRA2) != 0 1582 && (status0 & IOERR) != 0) { 1583 int now_lvd; 1584 1585 now_lvd = ahc_inb(ahc, SBLKCTL) & ENAB40; 1586 printk("%s: Transceiver State Has Changed to %s mode\n", 1587 ahc_name(ahc), now_lvd ? "LVD" : "SE"); 1588 ahc_outb(ahc, CLRSINT0, CLRIOERR); 1589 /* 1590 * When transitioning to SE mode, the reset line 1591 * glitches, triggering an arbitration bug in some 1592 * Ultra2 controllers. This bug is cleared when we 1593 * assert the reset line. Since a reset glitch has 1594 * already occurred with this transition and a 1595 * transceiver state change is handled just like 1596 * a bus reset anyway, asserting the reset line 1597 * ourselves is safe. 1598 */ 1599 ahc_reset_channel(ahc, intr_channel, 1600 /*Initiate Reset*/now_lvd == 0); 1601 } else if ((status & SCSIRSTI) != 0) { 1602 printk("%s: Someone reset channel %c\n", 1603 ahc_name(ahc), intr_channel); 1604 if (intr_channel != cur_channel) 1605 ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) ^ SELBUSB); 1606 ahc_reset_channel(ahc, intr_channel, /*Initiate Reset*/FALSE); 1607 } else if ((status & SCSIPERR) != 0) { 1608 /* 1609 * Determine the bus phase and queue an appropriate message. 1610 * SCSIPERR is latched true as soon as a parity error 1611 * occurs. If the sequencer acked the transfer that 1612 * caused the parity error and the currently presented 1613 * transfer on the bus has correct parity, SCSIPERR will 1614 * be cleared by CLRSCSIPERR. Use this to determine if 1615 * we should look at the last phase the sequencer recorded, 1616 * or the current phase presented on the bus. 1617 */ 1618 struct ahc_devinfo devinfo; 1619 u_int mesg_out; 1620 u_int curphase; 1621 u_int errorphase; 1622 u_int lastphase; 1623 u_int scsirate; 1624 u_int i; 1625 u_int sstat2; 1626 int silent; 1627 1628 lastphase = ahc_inb(ahc, LASTPHASE); 1629 curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; 1630 sstat2 = ahc_inb(ahc, SSTAT2); 1631 ahc_outb(ahc, CLRSINT1, CLRSCSIPERR); 1632 /* 1633 * For all phases save DATA, the sequencer won't 1634 * automatically ack a byte that has a parity error 1635 * in it. So the only way that the current phase 1636 * could be 'data-in' is if the parity error is for 1637 * an already acked byte in the data phase. During 1638 * synchronous data-in transfers, we may actually 1639 * ack bytes before latching the current phase in 1640 * LASTPHASE, leading to the discrepancy between 1641 * curphase and lastphase. 1642 */ 1643 if ((ahc_inb(ahc, SSTAT1) & SCSIPERR) != 0 1644 || curphase == P_DATAIN || curphase == P_DATAIN_DT) 1645 errorphase = curphase; 1646 else 1647 errorphase = lastphase; 1648 1649 for (i = 0; i < num_phases; i++) { 1650 if (errorphase == ahc_phase_table[i].phase) 1651 break; 1652 } 1653 mesg_out = ahc_phase_table[i].mesg_out; 1654 silent = FALSE; 1655 if (scb != NULL) { 1656 if (SCB_IS_SILENT(scb)) 1657 silent = TRUE; 1658 else 1659 ahc_print_path(ahc, scb); 1660 scb->flags |= SCB_TRANSMISSION_ERROR; 1661 } else 1662 printk("%s:%c:%d: ", ahc_name(ahc), intr_channel, 1663 SCSIID_TARGET(ahc, ahc_inb(ahc, SAVED_SCSIID))); 1664 scsirate = ahc_inb(ahc, SCSIRATE); 1665 if (silent == FALSE) { 1666 printk("parity error detected %s. " 1667 "SEQADDR(0x%x) SCSIRATE(0x%x)\n", 1668 ahc_phase_table[i].phasemsg, 1669 ahc_inw(ahc, SEQADDR0), 1670 scsirate); 1671 if ((ahc->features & AHC_DT) != 0) { 1672 if ((sstat2 & CRCVALERR) != 0) 1673 printk("\tCRC Value Mismatch\n"); 1674 if ((sstat2 & CRCENDERR) != 0) 1675 printk("\tNo terminal CRC packet " 1676 "recevied\n"); 1677 if ((sstat2 & CRCREQERR) != 0) 1678 printk("\tIllegal CRC packet " 1679 "request\n"); 1680 if ((sstat2 & DUAL_EDGE_ERR) != 0) 1681 printk("\tUnexpected %sDT Data Phase\n", 1682 (scsirate & SINGLE_EDGE) 1683 ? "" : "non-"); 1684 } 1685 } 1686 1687 if ((ahc->features & AHC_DT) != 0 1688 && (sstat2 & DUAL_EDGE_ERR) != 0) { 1689 /* 1690 * This error applies regardless of 1691 * data direction, so ignore the value 1692 * in the phase table. 1693 */ 1694 mesg_out = MSG_INITIATOR_DET_ERR; 1695 } 1696 1697 /* 1698 * We've set the hardware to assert ATN if we 1699 * get a parity error on "in" phases, so all we 1700 * need to do is stuff the message buffer with 1701 * the appropriate message. "In" phases have set 1702 * mesg_out to something other than MSG_NOP. 1703 */ 1704 if (mesg_out != MSG_NOOP) { 1705 if (ahc->msg_type != MSG_TYPE_NONE) 1706 ahc->send_msg_perror = TRUE; 1707 else 1708 ahc_outb(ahc, MSG_OUT, mesg_out); 1709 } 1710 /* 1711 * Force a renegotiation with this target just in 1712 * case we are out of sync for some external reason 1713 * unknown (or unreported) by the target. 1714 */ 1715 ahc_fetch_devinfo(ahc, &devinfo); 1716 ahc_force_renegotiation(ahc, &devinfo); 1717 1718 ahc_outb(ahc, CLRINT, CLRSCSIINT); 1719 ahc_unpause(ahc); 1720 } else if ((status & SELTO) != 0) { 1721 u_int scbptr; 1722 1723 /* Stop the selection */ 1724 ahc_outb(ahc, SCSISEQ, 0); 1725 1726 /* No more pending messages */ 1727 ahc_clear_msg_state(ahc); 1728 1729 /* Clear interrupt state */ 1730 ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); 1731 ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRBUSFREE|CLRSCSIPERR); 1732 1733 /* 1734 * Although the driver does not care about the 1735 * 'Selection in Progress' status bit, the busy 1736 * LED does. SELINGO is only cleared by a successful 1737 * selection, so we must manually clear it to insure 1738 * the LED turns off just incase no future successful 1739 * selections occur (e.g. no devices on the bus). 1740 */ 1741 ahc_outb(ahc, CLRSINT0, CLRSELINGO); 1742 1743 scbptr = ahc_inb(ahc, WAITING_SCBH); 1744 ahc_outb(ahc, SCBPTR, scbptr); 1745 scb_index = ahc_inb(ahc, SCB_TAG); 1746 1747 scb = ahc_lookup_scb(ahc, scb_index); 1748 if (scb == NULL) { 1749 printk("%s: ahc_intr - referenced scb not " 1750 "valid during SELTO scb(%d, %d)\n", 1751 ahc_name(ahc), scbptr, scb_index); 1752 ahc_dump_card_state(ahc); 1753 } else { 1754 struct ahc_devinfo devinfo; 1755#ifdef AHC_DEBUG 1756 if ((ahc_debug & AHC_SHOW_SELTO) != 0) { 1757 ahc_print_path(ahc, scb); 1758 printk("Saw Selection Timeout for SCB 0x%x\n", 1759 scb_index); 1760 } 1761#endif 1762 ahc_scb_devinfo(ahc, &devinfo, scb); 1763 ahc_set_transaction_status(scb, CAM_SEL_TIMEOUT); 1764 ahc_freeze_devq(ahc, scb); 1765 1766 /* 1767 * Cancel any pending transactions on the device 1768 * now that it seems to be missing. This will 1769 * also revert us to async/narrow transfers until 1770 * we can renegotiate with the device. 1771 */ 1772 ahc_handle_devreset(ahc, &devinfo, 1773 CAM_SEL_TIMEOUT, 1774 "Selection Timeout", 1775 /*verbose_level*/1); 1776 } 1777 ahc_outb(ahc, CLRINT, CLRSCSIINT); 1778 ahc_restart(ahc); 1779 } else if ((status & BUSFREE) != 0 1780 && (ahc_inb(ahc, SIMODE1) & ENBUSFREE) != 0) { 1781 struct ahc_devinfo devinfo; 1782 u_int lastphase; 1783 u_int saved_scsiid; 1784 u_int saved_lun; 1785 u_int target; 1786 u_int initiator_role_id; 1787 char channel; 1788 int printerror; 1789 1790 /* 1791 * Clear our selection hardware as soon as possible. 1792 * We may have an entry in the waiting Q for this target, 1793 * that is affected by this busfree and we don't want to 1794 * go about selecting the target while we handle the event. 1795 */ 1796 ahc_outb(ahc, SCSISEQ, 1797 ahc_inb(ahc, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP)); 1798 1799 /* 1800 * Disable busfree interrupts and clear the busfree 1801 * interrupt status. We do this here so that several 1802 * bus transactions occur prior to clearing the SCSIINT 1803 * latch. It can take a bit for the clearing to take effect. 1804 */ 1805 ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); 1806 ahc_outb(ahc, CLRSINT1, CLRBUSFREE|CLRSCSIPERR); 1807 1808 /* 1809 * Look at what phase we were last in. 1810 * If its message out, chances are pretty good 1811 * that the busfree was in response to one of 1812 * our abort requests. 1813 */ 1814 lastphase = ahc_inb(ahc, LASTPHASE); 1815 saved_scsiid = ahc_inb(ahc, SAVED_SCSIID); 1816 saved_lun = ahc_inb(ahc, SAVED_LUN); 1817 target = SCSIID_TARGET(ahc, saved_scsiid); 1818 initiator_role_id = SCSIID_OUR_ID(saved_scsiid); 1819 channel = SCSIID_CHANNEL(ahc, saved_scsiid); 1820 ahc_compile_devinfo(&devinfo, initiator_role_id, 1821 target, saved_lun, channel, ROLE_INITIATOR); 1822 printerror = 1; 1823 1824 if (lastphase == P_MESGOUT) { 1825 u_int tag; 1826 1827 tag = SCB_LIST_NULL; 1828 if (ahc_sent_msg(ahc, AHCMSG_1B, MSG_ABORT_TAG, TRUE) 1829 || ahc_sent_msg(ahc, AHCMSG_1B, MSG_ABORT, TRUE)) { 1830 if (ahc->msgout_buf[ahc->msgout_index - 1] 1831 == MSG_ABORT_TAG) 1832 tag = scb->hscb->tag; 1833 ahc_print_path(ahc, scb); 1834 printk("SCB %d - Abort%s Completed.\n", 1835 scb->hscb->tag, tag == SCB_LIST_NULL ? 1836 "" : " Tag"); 1837 ahc_abort_scbs(ahc, target, channel, 1838 saved_lun, tag, 1839 ROLE_INITIATOR, 1840 CAM_REQ_ABORTED); 1841 printerror = 0; 1842 } else if (ahc_sent_msg(ahc, AHCMSG_1B, 1843 MSG_BUS_DEV_RESET, TRUE)) { 1844#ifdef __FreeBSD__ 1845 /* 1846 * Don't mark the user's request for this BDR 1847 * as completing with CAM_BDR_SENT. CAM3 1848 * specifies CAM_REQ_CMP. 1849 */ 1850 if (scb != NULL 1851 && scb->io_ctx->ccb_h.func_code== XPT_RESET_DEV 1852 && ahc_match_scb(ahc, scb, target, channel, 1853 CAM_LUN_WILDCARD, 1854 SCB_LIST_NULL, 1855 ROLE_INITIATOR)) { 1856 ahc_set_transaction_status(scb, CAM_REQ_CMP); 1857 } 1858#endif 1859 ahc_compile_devinfo(&devinfo, 1860 initiator_role_id, 1861 target, 1862 CAM_LUN_WILDCARD, 1863 channel, 1864 ROLE_INITIATOR); 1865 ahc_handle_devreset(ahc, &devinfo, 1866 CAM_BDR_SENT, 1867 "Bus Device Reset", 1868 /*verbose_level*/0); 1869 printerror = 0; 1870 } else if (ahc_sent_msg(ahc, AHCMSG_EXT, 1871 MSG_EXT_PPR, FALSE)) { 1872 struct ahc_initiator_tinfo *tinfo; 1873 struct ahc_tmode_tstate *tstate; 1874 1875 /* 1876 * PPR Rejected. Try non-ppr negotiation 1877 * and retry command. 1878 */ 1879 tinfo = ahc_fetch_transinfo(ahc, 1880 devinfo.channel, 1881 devinfo.our_scsiid, 1882 devinfo.target, 1883 &tstate); 1884 tinfo->curr.transport_version = 2; 1885 tinfo->goal.transport_version = 2; 1886 tinfo->goal.ppr_options = 0; 1887 ahc_qinfifo_requeue_tail(ahc, scb); 1888 printerror = 0; 1889 } else if (ahc_sent_msg(ahc, AHCMSG_EXT, 1890 MSG_EXT_WDTR, FALSE)) { 1891 /* 1892 * Negotiation Rejected. Go-narrow and 1893 * retry command. 1894 */ 1895 ahc_set_width(ahc, &devinfo, 1896 MSG_EXT_WDTR_BUS_8_BIT, 1897 AHC_TRANS_CUR|AHC_TRANS_GOAL, 1898 /*paused*/TRUE); 1899 ahc_qinfifo_requeue_tail(ahc, scb); 1900 printerror = 0; 1901 } else if (ahc_sent_msg(ahc, AHCMSG_EXT, 1902 MSG_EXT_SDTR, FALSE)) { 1903 /* 1904 * Negotiation Rejected. Go-async and 1905 * retry command. 1906 */ 1907 ahc_set_syncrate(ahc, &devinfo, 1908 /*syncrate*/NULL, 1909 /*period*/0, /*offset*/0, 1910 /*ppr_options*/0, 1911 AHC_TRANS_CUR|AHC_TRANS_GOAL, 1912 /*paused*/TRUE); 1913 ahc_qinfifo_requeue_tail(ahc, scb); 1914 printerror = 0; 1915 } 1916 } 1917 if (printerror != 0) { 1918 u_int i; 1919 1920 if (scb != NULL) { 1921 u_int tag; 1922 1923 if ((scb->hscb->control & TAG_ENB) != 0) 1924 tag = scb->hscb->tag; 1925 else 1926 tag = SCB_LIST_NULL; 1927 ahc_print_path(ahc, scb); 1928 ahc_abort_scbs(ahc, target, channel, 1929 SCB_GET_LUN(scb), tag, 1930 ROLE_INITIATOR, 1931 CAM_UNEXP_BUSFREE); 1932 } else { 1933 /* 1934 * We had not fully identified this connection, 1935 * so we cannot abort anything. 1936 */ 1937 printk("%s: ", ahc_name(ahc)); 1938 } 1939 for (i = 0; i < num_phases; i++) { 1940 if (lastphase == ahc_phase_table[i].phase) 1941 break; 1942 } 1943 if (lastphase != P_BUSFREE) { 1944 /* 1945 * Renegotiate with this device at the 1946 * next opportunity just in case this busfree 1947 * is due to a negotiation mismatch with the 1948 * device. 1949 */ 1950 ahc_force_renegotiation(ahc, &devinfo); 1951 } 1952 printk("Unexpected busfree %s\n" 1953 "SEQADDR == 0x%x\n", 1954 ahc_phase_table[i].phasemsg, 1955 ahc_inb(ahc, SEQADDR0) 1956 | (ahc_inb(ahc, SEQADDR1) << 8)); 1957 } 1958 ahc_outb(ahc, CLRINT, CLRSCSIINT); 1959 ahc_restart(ahc); 1960 } else { 1961 printk("%s: Missing case in ahc_handle_scsiint. status = %x\n", 1962 ahc_name(ahc), status); 1963 ahc_outb(ahc, CLRINT, CLRSCSIINT); 1964 } 1965} 1966 1967/* 1968 * Force renegotiation to occur the next time we initiate 1969 * a command to the current device. 1970 */ 1971static void 1972ahc_force_renegotiation(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 1973{ 1974 struct ahc_initiator_tinfo *targ_info; 1975 struct ahc_tmode_tstate *tstate; 1976 1977 targ_info = ahc_fetch_transinfo(ahc, 1978 devinfo->channel, 1979 devinfo->our_scsiid, 1980 devinfo->target, 1981 &tstate); 1982 ahc_update_neg_request(ahc, devinfo, tstate, 1983 targ_info, AHC_NEG_IF_NON_ASYNC); 1984} 1985 1986#define AHC_MAX_STEPS 2000 1987static void 1988ahc_clear_critical_section(struct ahc_softc *ahc) 1989{ 1990 int stepping; 1991 int steps; 1992 u_int simode0; 1993 u_int simode1; 1994 1995 if (ahc->num_critical_sections == 0) 1996 return; 1997 1998 stepping = FALSE; 1999 steps = 0; 2000 simode0 = 0; 2001 simode1 = 0; 2002 for (;;) { 2003 struct cs *cs; 2004 u_int seqaddr; 2005 u_int i; 2006 2007 seqaddr = ahc_inb(ahc, SEQADDR0) 2008 | (ahc_inb(ahc, SEQADDR1) << 8); 2009 2010 /* 2011 * Seqaddr represents the next instruction to execute, 2012 * so we are really executing the instruction just 2013 * before it. 2014 */ 2015 if (seqaddr != 0) 2016 seqaddr -= 1; 2017 cs = ahc->critical_sections; 2018 for (i = 0; i < ahc->num_critical_sections; i++, cs++) { 2019 2020 if (cs->begin < seqaddr && cs->end >= seqaddr) 2021 break; 2022 } 2023 2024 if (i == ahc->num_critical_sections) 2025 break; 2026 2027 if (steps > AHC_MAX_STEPS) { 2028 printk("%s: Infinite loop in critical section\n", 2029 ahc_name(ahc)); 2030 ahc_dump_card_state(ahc); 2031 panic("critical section loop"); 2032 } 2033 2034 steps++; 2035 if (stepping == FALSE) { 2036 2037 /* 2038 * Disable all interrupt sources so that the 2039 * sequencer will not be stuck by a pausing 2040 * interrupt condition while we attempt to 2041 * leave a critical section. 2042 */ 2043 simode0 = ahc_inb(ahc, SIMODE0); 2044 ahc_outb(ahc, SIMODE0, 0); 2045 simode1 = ahc_inb(ahc, SIMODE1); 2046 if ((ahc->features & AHC_DT) != 0) 2047 /* 2048 * On DT class controllers, we 2049 * use the enhanced busfree logic. 2050 * Unfortunately we cannot re-enable 2051 * busfree detection within the 2052 * current connection, so we must 2053 * leave it on while single stepping. 2054 */ 2055 ahc_outb(ahc, SIMODE1, simode1 & ENBUSFREE); 2056 else 2057 ahc_outb(ahc, SIMODE1, 0); 2058 ahc_outb(ahc, CLRINT, CLRSCSIINT); 2059 ahc_outb(ahc, SEQCTL, ahc->seqctl | STEP); 2060 stepping = TRUE; 2061 } 2062 if ((ahc->features & AHC_DT) != 0) { 2063 ahc_outb(ahc, CLRSINT1, CLRBUSFREE); 2064 ahc_outb(ahc, CLRINT, CLRSCSIINT); 2065 } 2066 ahc_outb(ahc, HCNTRL, ahc->unpause); 2067 while (!ahc_is_paused(ahc)) 2068 ahc_delay(200); 2069 } 2070 if (stepping) { 2071 ahc_outb(ahc, SIMODE0, simode0); 2072 ahc_outb(ahc, SIMODE1, simode1); 2073 ahc_outb(ahc, SEQCTL, ahc->seqctl); 2074 } 2075} 2076 2077/* 2078 * Clear any pending interrupt status. 2079 */ 2080static void 2081ahc_clear_intstat(struct ahc_softc *ahc) 2082{ 2083 /* Clear any interrupt conditions this may have caused */ 2084 ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRATNO|CLRSCSIRSTI 2085 |CLRBUSFREE|CLRSCSIPERR|CLRPHASECHG| 2086 CLRREQINIT); 2087 ahc_flush_device_writes(ahc); 2088 ahc_outb(ahc, CLRSINT0, CLRSELDO|CLRSELDI|CLRSELINGO); 2089 ahc_flush_device_writes(ahc); 2090 ahc_outb(ahc, CLRINT, CLRSCSIINT); 2091 ahc_flush_device_writes(ahc); 2092} 2093 2094/**************************** Debugging Routines ******************************/ 2095#ifdef AHC_DEBUG 2096uint32_t ahc_debug = AHC_DEBUG_OPTS; 2097#endif 2098 2099#if 0 /* unused */ 2100static void 2101ahc_print_scb(struct scb *scb) 2102{ 2103 int i; 2104 2105 struct hardware_scb *hscb = scb->hscb; 2106 2107 printk("scb:%p control:0x%x scsiid:0x%x lun:%d cdb_len:%d\n", 2108 (void *)scb, 2109 hscb->control, 2110 hscb->scsiid, 2111 hscb->lun, 2112 hscb->cdb_len); 2113 printk("Shared Data: "); 2114 for (i = 0; i < sizeof(hscb->shared_data.cdb); i++) 2115 printk("%#02x", hscb->shared_data.cdb[i]); 2116 printk(" dataptr:%#x datacnt:%#x sgptr:%#x tag:%#x\n", 2117 ahc_le32toh(hscb->dataptr), 2118 ahc_le32toh(hscb->datacnt), 2119 ahc_le32toh(hscb->sgptr), 2120 hscb->tag); 2121 if (scb->sg_count > 0) { 2122 for (i = 0; i < scb->sg_count; i++) { 2123 printk("sg[%d] - Addr 0x%x%x : Length %d\n", 2124 i, 2125 (ahc_le32toh(scb->sg_list[i].len) >> 24 2126 & SG_HIGH_ADDR_BITS), 2127 ahc_le32toh(scb->sg_list[i].addr), 2128 ahc_le32toh(scb->sg_list[i].len)); 2129 } 2130 } 2131} 2132#endif 2133 2134/************************* Transfer Negotiation *******************************/ 2135/* 2136 * Allocate per target mode instance (ID we respond to as a target) 2137 * transfer negotiation data structures. 2138 */ 2139static struct ahc_tmode_tstate * 2140ahc_alloc_tstate(struct ahc_softc *ahc, u_int scsi_id, char channel) 2141{ 2142 struct ahc_tmode_tstate *master_tstate; 2143 struct ahc_tmode_tstate *tstate; 2144 int i; 2145 2146 master_tstate = ahc->enabled_targets[ahc->our_id]; 2147 if (channel == 'B') { 2148 scsi_id += 8; 2149 master_tstate = ahc->enabled_targets[ahc->our_id_b + 8]; 2150 } 2151 if (ahc->enabled_targets[scsi_id] != NULL 2152 && ahc->enabled_targets[scsi_id] != master_tstate) 2153 panic("%s: ahc_alloc_tstate - Target already allocated", 2154 ahc_name(ahc)); 2155 tstate = kmalloc(sizeof(*tstate), GFP_ATOMIC); 2156 if (tstate == NULL) 2157 return (NULL); 2158 2159 /* 2160 * If we have allocated a master tstate, copy user settings from 2161 * the master tstate (taken from SRAM or the EEPROM) for this 2162 * channel, but reset our current and goal settings to async/narrow 2163 * until an initiator talks to us. 2164 */ 2165 if (master_tstate != NULL) { 2166 memcpy(tstate, master_tstate, sizeof(*tstate)); 2167 memset(tstate->enabled_luns, 0, sizeof(tstate->enabled_luns)); 2168 tstate->ultraenb = 0; 2169 for (i = 0; i < AHC_NUM_TARGETS; i++) { 2170 memset(&tstate->transinfo[i].curr, 0, 2171 sizeof(tstate->transinfo[i].curr)); 2172 memset(&tstate->transinfo[i].goal, 0, 2173 sizeof(tstate->transinfo[i].goal)); 2174 } 2175 } else 2176 memset(tstate, 0, sizeof(*tstate)); 2177 ahc->enabled_targets[scsi_id] = tstate; 2178 return (tstate); 2179} 2180 2181#ifdef AHC_TARGET_MODE 2182/* 2183 * Free per target mode instance (ID we respond to as a target) 2184 * transfer negotiation data structures. 2185 */ 2186static void 2187ahc_free_tstate(struct ahc_softc *ahc, u_int scsi_id, char channel, int force) 2188{ 2189 struct ahc_tmode_tstate *tstate; 2190 2191 /* 2192 * Don't clean up our "master" tstate. 2193 * It has our default user settings. 2194 */ 2195 if (((channel == 'B' && scsi_id == ahc->our_id_b) 2196 || (channel == 'A' && scsi_id == ahc->our_id)) 2197 && force == FALSE) 2198 return; 2199 2200 if (channel == 'B') 2201 scsi_id += 8; 2202 tstate = ahc->enabled_targets[scsi_id]; 2203 if (tstate != NULL) 2204 kfree(tstate); 2205 ahc->enabled_targets[scsi_id] = NULL; 2206} 2207#endif 2208 2209/* 2210 * Called when we have an active connection to a target on the bus, 2211 * this function finds the nearest syncrate to the input period limited 2212 * by the capabilities of the bus connectivity of and sync settings for 2213 * the target. 2214 */ 2215const struct ahc_syncrate * 2216ahc_devlimited_syncrate(struct ahc_softc *ahc, 2217 struct ahc_initiator_tinfo *tinfo, 2218 u_int *period, u_int *ppr_options, role_t role) 2219{ 2220 struct ahc_transinfo *transinfo; 2221 u_int maxsync; 2222 2223 if ((ahc->features & AHC_ULTRA2) != 0) { 2224 if ((ahc_inb(ahc, SBLKCTL) & ENAB40) != 0 2225 && (ahc_inb(ahc, SSTAT2) & EXP_ACTIVE) == 0) { 2226 maxsync = AHC_SYNCRATE_DT; 2227 } else { 2228 maxsync = AHC_SYNCRATE_ULTRA; 2229 /* Can't do DT on an SE bus */ 2230 *ppr_options &= ~MSG_EXT_PPR_DT_REQ; 2231 } 2232 } else if ((ahc->features & AHC_ULTRA) != 0) { 2233 maxsync = AHC_SYNCRATE_ULTRA; 2234 } else { 2235 maxsync = AHC_SYNCRATE_FAST; 2236 } 2237 /* 2238 * Never allow a value higher than our current goal 2239 * period otherwise we may allow a target initiated 2240 * negotiation to go above the limit as set by the 2241 * user. In the case of an initiator initiated 2242 * sync negotiation, we limit based on the user 2243 * setting. This allows the system to still accept 2244 * incoming negotiations even if target initiated 2245 * negotiation is not performed. 2246 */ 2247 if (role == ROLE_TARGET) 2248 transinfo = &tinfo->user; 2249 else 2250 transinfo = &tinfo->goal; 2251 *ppr_options &= transinfo->ppr_options; 2252 if (transinfo->width == MSG_EXT_WDTR_BUS_8_BIT) { 2253 maxsync = max(maxsync, (u_int)AHC_SYNCRATE_ULTRA2); 2254 *ppr_options &= ~MSG_EXT_PPR_DT_REQ; 2255 } 2256 if (transinfo->period == 0) { 2257 *period = 0; 2258 *ppr_options = 0; 2259 return (NULL); 2260 } 2261 *period = max(*period, (u_int)transinfo->period); 2262 return (ahc_find_syncrate(ahc, period, ppr_options, maxsync)); 2263} 2264 2265/* 2266 * Look up the valid period to SCSIRATE conversion in our table. 2267 * Return the period and offset that should be sent to the target 2268 * if this was the beginning of an SDTR. 2269 */ 2270const struct ahc_syncrate * 2271ahc_find_syncrate(struct ahc_softc *ahc, u_int *period, 2272 u_int *ppr_options, u_int maxsync) 2273{ 2274 const struct ahc_syncrate *syncrate; 2275 2276 if ((ahc->features & AHC_DT) == 0) 2277 *ppr_options &= ~MSG_EXT_PPR_DT_REQ; 2278 2279 /* Skip all DT only entries if DT is not available */ 2280 if ((*ppr_options & MSG_EXT_PPR_DT_REQ) == 0 2281 && maxsync < AHC_SYNCRATE_ULTRA2) 2282 maxsync = AHC_SYNCRATE_ULTRA2; 2283 2284 /* Now set the maxsync based on the card capabilities 2285 * DT is already done above */ 2286 if ((ahc->features & (AHC_DT | AHC_ULTRA2)) == 0 2287 && maxsync < AHC_SYNCRATE_ULTRA) 2288 maxsync = AHC_SYNCRATE_ULTRA; 2289 if ((ahc->features & (AHC_DT | AHC_ULTRA2 | AHC_ULTRA)) == 0 2290 && maxsync < AHC_SYNCRATE_FAST) 2291 maxsync = AHC_SYNCRATE_FAST; 2292 2293 for (syncrate = &ahc_syncrates[maxsync]; 2294 syncrate->rate != NULL; 2295 syncrate++) { 2296 2297 /* 2298 * The Ultra2 table doesn't go as low 2299 * as for the Fast/Ultra cards. 2300 */ 2301 if ((ahc->features & AHC_ULTRA2) != 0 2302 && (syncrate->sxfr_u2 == 0)) 2303 break; 2304 2305 if (*period <= syncrate->period) { 2306 /* 2307 * When responding to a target that requests 2308 * sync, the requested rate may fall between 2309 * two rates that we can output, but still be 2310 * a rate that we can receive. Because of this, 2311 * we want to respond to the target with 2312 * the same rate that it sent to us even 2313 * if the period we use to send data to it 2314 * is lower. Only lower the response period 2315 * if we must. 2316 */ 2317 if (syncrate == &ahc_syncrates[maxsync]) 2318 *period = syncrate->period; 2319 2320 /* 2321 * At some speeds, we only support 2322 * ST transfers. 2323 */ 2324 if ((syncrate->sxfr_u2 & ST_SXFR) != 0) 2325 *ppr_options &= ~MSG_EXT_PPR_DT_REQ; 2326 break; 2327 } 2328 } 2329 2330 if ((*period == 0) 2331 || (syncrate->rate == NULL) 2332 || ((ahc->features & AHC_ULTRA2) != 0 2333 && (syncrate->sxfr_u2 == 0))) { 2334 /* Use asynchronous transfers. */ 2335 *period = 0; 2336 syncrate = NULL; 2337 *ppr_options &= ~MSG_EXT_PPR_DT_REQ; 2338 } 2339 return (syncrate); 2340} 2341 2342/* 2343 * Convert from an entry in our syncrate table to the SCSI equivalent 2344 * sync "period" factor. 2345 */ 2346u_int 2347ahc_find_period(struct ahc_softc *ahc, u_int scsirate, u_int maxsync) 2348{ 2349 const struct ahc_syncrate *syncrate; 2350 2351 if ((ahc->features & AHC_ULTRA2) != 0) 2352 scsirate &= SXFR_ULTRA2; 2353 else 2354 scsirate &= SXFR; 2355 2356 /* now set maxsync based on card capabilities */ 2357 if ((ahc->features & AHC_DT) == 0 && maxsync < AHC_SYNCRATE_ULTRA2) 2358 maxsync = AHC_SYNCRATE_ULTRA2; 2359 if ((ahc->features & (AHC_DT | AHC_ULTRA2)) == 0 2360 && maxsync < AHC_SYNCRATE_ULTRA) 2361 maxsync = AHC_SYNCRATE_ULTRA; 2362 if ((ahc->features & (AHC_DT | AHC_ULTRA2 | AHC_ULTRA)) == 0 2363 && maxsync < AHC_SYNCRATE_FAST) 2364 maxsync = AHC_SYNCRATE_FAST; 2365 2366 2367 syncrate = &ahc_syncrates[maxsync]; 2368 while (syncrate->rate != NULL) { 2369 2370 if ((ahc->features & AHC_ULTRA2) != 0) { 2371 if (syncrate->sxfr_u2 == 0) 2372 break; 2373 else if (scsirate == (syncrate->sxfr_u2 & SXFR_ULTRA2)) 2374 return (syncrate->period); 2375 } else if (scsirate == (syncrate->sxfr & SXFR)) { 2376 return (syncrate->period); 2377 } 2378 syncrate++; 2379 } 2380 return (0); /* async */ 2381} 2382 2383/* 2384 * Truncate the given synchronous offset to a value the 2385 * current adapter type and syncrate are capable of. 2386 */ 2387static void 2388ahc_validate_offset(struct ahc_softc *ahc, 2389 struct ahc_initiator_tinfo *tinfo, 2390 const struct ahc_syncrate *syncrate, 2391 u_int *offset, int wide, role_t role) 2392{ 2393 u_int maxoffset; 2394 2395 /* Limit offset to what we can do */ 2396 if (syncrate == NULL) { 2397 maxoffset = 0; 2398 } else if ((ahc->features & AHC_ULTRA2) != 0) { 2399 maxoffset = MAX_OFFSET_ULTRA2; 2400 } else { 2401 if (wide) 2402 maxoffset = MAX_OFFSET_16BIT; 2403 else 2404 maxoffset = MAX_OFFSET_8BIT; 2405 } 2406 *offset = min(*offset, maxoffset); 2407 if (tinfo != NULL) { 2408 if (role == ROLE_TARGET) 2409 *offset = min(*offset, (u_int)tinfo->user.offset); 2410 else 2411 *offset = min(*offset, (u_int)tinfo->goal.offset); 2412 } 2413} 2414 2415/* 2416 * Truncate the given transfer width parameter to a value the 2417 * current adapter type is capable of. 2418 */ 2419static void 2420ahc_validate_width(struct ahc_softc *ahc, struct ahc_initiator_tinfo *tinfo, 2421 u_int *bus_width, role_t role) 2422{ 2423 switch (*bus_width) { 2424 default: 2425 if (ahc->features & AHC_WIDE) { 2426 /* Respond Wide */ 2427 *bus_width = MSG_EXT_WDTR_BUS_16_BIT; 2428 break; 2429 } 2430 /* FALLTHROUGH */ 2431 case MSG_EXT_WDTR_BUS_8_BIT: 2432 *bus_width = MSG_EXT_WDTR_BUS_8_BIT; 2433 break; 2434 } 2435 if (tinfo != NULL) { 2436 if (role == ROLE_TARGET) 2437 *bus_width = min((u_int)tinfo->user.width, *bus_width); 2438 else 2439 *bus_width = min((u_int)tinfo->goal.width, *bus_width); 2440 } 2441} 2442 2443/* 2444 * Update the bitmask of targets for which the controller should 2445 * negotiate with at the next convenient opportunity. This currently 2446 * means the next time we send the initial identify messages for 2447 * a new transaction. 2448 */ 2449int 2450ahc_update_neg_request(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 2451 struct ahc_tmode_tstate *tstate, 2452 struct ahc_initiator_tinfo *tinfo, ahc_neg_type neg_type) 2453{ 2454 u_int auto_negotiate_orig; 2455 2456 auto_negotiate_orig = tstate->auto_negotiate; 2457 if (neg_type == AHC_NEG_ALWAYS) { 2458 /* 2459 * Force our "current" settings to be 2460 * unknown so that unless a bus reset 2461 * occurs the need to renegotiate is 2462 * recorded persistently. 2463 */ 2464 if ((ahc->features & AHC_WIDE) != 0) 2465 tinfo->curr.width = AHC_WIDTH_UNKNOWN; 2466 tinfo->curr.period = AHC_PERIOD_UNKNOWN; 2467 tinfo->curr.offset = AHC_OFFSET_UNKNOWN; 2468 } 2469 if (tinfo->curr.period != tinfo->goal.period 2470 || tinfo->curr.width != tinfo->goal.width 2471 || tinfo->curr.offset != tinfo->goal.offset 2472 || tinfo->curr.ppr_options != tinfo->goal.ppr_options 2473 || (neg_type == AHC_NEG_IF_NON_ASYNC 2474 && (tinfo->goal.offset != 0 2475 || tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT 2476 || tinfo->goal.ppr_options != 0))) 2477 tstate->auto_negotiate |= devinfo->target_mask; 2478 else 2479 tstate->auto_negotiate &= ~devinfo->target_mask; 2480 2481 return (auto_negotiate_orig != tstate->auto_negotiate); 2482} 2483 2484/* 2485 * Update the user/goal/curr tables of synchronous negotiation 2486 * parameters as well as, in the case of a current or active update, 2487 * any data structures on the host controller. In the case of an 2488 * active update, the specified target is currently talking to us on 2489 * the bus, so the transfer parameter update must take effect 2490 * immediately. 2491 */ 2492void 2493ahc_set_syncrate(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 2494 const struct ahc_syncrate *syncrate, u_int period, 2495 u_int offset, u_int ppr_options, u_int type, int paused) 2496{ 2497 struct ahc_initiator_tinfo *tinfo; 2498 struct ahc_tmode_tstate *tstate; 2499 u_int old_period; 2500 u_int old_offset; 2501 u_int old_ppr; 2502 int active; 2503 int update_needed; 2504 2505 active = (type & AHC_TRANS_ACTIVE) == AHC_TRANS_ACTIVE; 2506 update_needed = 0; 2507 2508 if (syncrate == NULL) { 2509 period = 0; 2510 offset = 0; 2511 } 2512 2513 tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, 2514 devinfo->target, &tstate); 2515 2516 if ((type & AHC_TRANS_USER) != 0) { 2517 tinfo->user.period = period; 2518 tinfo->user.offset = offset; 2519 tinfo->user.ppr_options = ppr_options; 2520 } 2521 2522 if ((type & AHC_TRANS_GOAL) != 0) { 2523 tinfo->goal.period = period; 2524 tinfo->goal.offset = offset; 2525 tinfo->goal.ppr_options = ppr_options; 2526 } 2527 2528 old_period = tinfo->curr.period; 2529 old_offset = tinfo->curr.offset; 2530 old_ppr = tinfo->curr.ppr_options; 2531 2532 if ((type & AHC_TRANS_CUR) != 0 2533 && (old_period != period 2534 || old_offset != offset 2535 || old_ppr != ppr_options)) { 2536 u_int scsirate; 2537 2538 update_needed++; 2539 scsirate = tinfo->scsirate; 2540 if ((ahc->features & AHC_ULTRA2) != 0) { 2541 2542 scsirate &= ~(SXFR_ULTRA2|SINGLE_EDGE|ENABLE_CRC); 2543 if (syncrate != NULL) { 2544 scsirate |= syncrate->sxfr_u2; 2545 if ((ppr_options & MSG_EXT_PPR_DT_REQ) != 0) 2546 scsirate |= ENABLE_CRC; 2547 else 2548 scsirate |= SINGLE_EDGE; 2549 } 2550 } else { 2551 2552 scsirate &= ~(SXFR|SOFS); 2553 /* 2554 * Ensure Ultra mode is set properly for 2555 * this target. 2556 */ 2557 tstate->ultraenb &= ~devinfo->target_mask; 2558 if (syncrate != NULL) { 2559 if (syncrate->sxfr & ULTRA_SXFR) { 2560 tstate->ultraenb |= 2561 devinfo->target_mask; 2562 } 2563 scsirate |= syncrate->sxfr & SXFR; 2564 scsirate |= offset & SOFS; 2565 } 2566 if (active) { 2567 u_int sxfrctl0; 2568 2569 sxfrctl0 = ahc_inb(ahc, SXFRCTL0); 2570 sxfrctl0 &= ~FAST20; 2571 if (tstate->ultraenb & devinfo->target_mask) 2572 sxfrctl0 |= FAST20; 2573 ahc_outb(ahc, SXFRCTL0, sxfrctl0); 2574 } 2575 } 2576 if (active) { 2577 ahc_outb(ahc, SCSIRATE, scsirate); 2578 if ((ahc->features & AHC_ULTRA2) != 0) 2579 ahc_outb(ahc, SCSIOFFSET, offset); 2580 } 2581 2582 tinfo->scsirate = scsirate; 2583 tinfo->curr.period = period; 2584 tinfo->curr.offset = offset; 2585 tinfo->curr.ppr_options = ppr_options; 2586 2587 ahc_send_async(ahc, devinfo->channel, devinfo->target, 2588 CAM_LUN_WILDCARD, AC_TRANSFER_NEG); 2589 if (bootverbose) { 2590 if (offset != 0) { 2591 printk("%s: target %d synchronous at %sMHz%s, " 2592 "offset = 0x%x\n", ahc_name(ahc), 2593 devinfo->target, syncrate->rate, 2594 (ppr_options & MSG_EXT_PPR_DT_REQ) 2595 ? " DT" : "", offset); 2596 } else { 2597 printk("%s: target %d using " 2598 "asynchronous transfers\n", 2599 ahc_name(ahc), devinfo->target); 2600 } 2601 } 2602 } 2603 2604 update_needed += ahc_update_neg_request(ahc, devinfo, tstate, 2605 tinfo, AHC_NEG_TO_GOAL); 2606 2607 if (update_needed) 2608 ahc_update_pending_scbs(ahc); 2609} 2610 2611/* 2612 * Update the user/goal/curr tables of wide negotiation 2613 * parameters as well as, in the case of a current or active update, 2614 * any data structures on the host controller. In the case of an 2615 * active update, the specified target is currently talking to us on 2616 * the bus, so the transfer parameter update must take effect 2617 * immediately. 2618 */ 2619void 2620ahc_set_width(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 2621 u_int width, u_int type, int paused) 2622{ 2623 struct ahc_initiator_tinfo *tinfo; 2624 struct ahc_tmode_tstate *tstate; 2625 u_int oldwidth; 2626 int active; 2627 int update_needed; 2628 2629 active = (type & AHC_TRANS_ACTIVE) == AHC_TRANS_ACTIVE; 2630 update_needed = 0; 2631 tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, 2632 devinfo->target, &tstate); 2633 2634 if ((type & AHC_TRANS_USER) != 0) 2635 tinfo->user.width = width; 2636 2637 if ((type & AHC_TRANS_GOAL) != 0) 2638 tinfo->goal.width = width; 2639 2640 oldwidth = tinfo->curr.width; 2641 if ((type & AHC_TRANS_CUR) != 0 && oldwidth != width) { 2642 u_int scsirate; 2643 2644 update_needed++; 2645 scsirate = tinfo->scsirate; 2646 scsirate &= ~WIDEXFER; 2647 if (width == MSG_EXT_WDTR_BUS_16_BIT) 2648 scsirate |= WIDEXFER; 2649 2650 tinfo->scsirate = scsirate; 2651 2652 if (active) 2653 ahc_outb(ahc, SCSIRATE, scsirate); 2654 2655 tinfo->curr.width = width; 2656 2657 ahc_send_async(ahc, devinfo->channel, devinfo->target, 2658 CAM_LUN_WILDCARD, AC_TRANSFER_NEG); 2659 if (bootverbose) { 2660 printk("%s: target %d using %dbit transfers\n", 2661 ahc_name(ahc), devinfo->target, 2662 8 * (0x01 << width)); 2663 } 2664 } 2665 2666 update_needed += ahc_update_neg_request(ahc, devinfo, tstate, 2667 tinfo, AHC_NEG_TO_GOAL); 2668 if (update_needed) 2669 ahc_update_pending_scbs(ahc); 2670} 2671 2672/* 2673 * Update the current state of tagged queuing for a given target. 2674 */ 2675static void 2676ahc_set_tags(struct ahc_softc *ahc, struct scsi_cmnd *cmd, 2677 struct ahc_devinfo *devinfo, ahc_queue_alg alg) 2678{ 2679 struct scsi_device *sdev = cmd->device; 2680 2681 ahc_platform_set_tags(ahc, sdev, devinfo, alg); 2682 ahc_send_async(ahc, devinfo->channel, devinfo->target, 2683 devinfo->lun, AC_TRANSFER_NEG); 2684} 2685 2686/* 2687 * When the transfer settings for a connection change, update any 2688 * in-transit SCBs to contain the new data so the hardware will 2689 * be set correctly during future (re)selections. 2690 */ 2691static void 2692ahc_update_pending_scbs(struct ahc_softc *ahc) 2693{ 2694 struct scb *pending_scb; 2695 int pending_scb_count; 2696 int i; 2697 int paused; 2698 u_int saved_scbptr; 2699 2700 /* 2701 * Traverse the pending SCB list and ensure that all of the 2702 * SCBs there have the proper settings. 2703 */ 2704 pending_scb_count = 0; 2705 LIST_FOREACH(pending_scb, &ahc->pending_scbs, pending_links) { 2706 struct ahc_devinfo devinfo; 2707 struct hardware_scb *pending_hscb; 2708 struct ahc_initiator_tinfo *tinfo; 2709 struct ahc_tmode_tstate *tstate; 2710 2711 ahc_scb_devinfo(ahc, &devinfo, pending_scb); 2712 tinfo = ahc_fetch_transinfo(ahc, devinfo.channel, 2713 devinfo.our_scsiid, 2714 devinfo.target, &tstate); 2715 pending_hscb = pending_scb->hscb; 2716 pending_hscb->control &= ~ULTRAENB; 2717 if ((tstate->ultraenb & devinfo.target_mask) != 0) 2718 pending_hscb->control |= ULTRAENB; 2719 pending_hscb->scsirate = tinfo->scsirate; 2720 pending_hscb->scsioffset = tinfo->curr.offset; 2721 if ((tstate->auto_negotiate & devinfo.target_mask) == 0 2722 && (pending_scb->flags & SCB_AUTO_NEGOTIATE) != 0) { 2723 pending_scb->flags &= ~SCB_AUTO_NEGOTIATE; 2724 pending_hscb->control &= ~MK_MESSAGE; 2725 } 2726 ahc_sync_scb(ahc, pending_scb, 2727 BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); 2728 pending_scb_count++; 2729 } 2730 2731 if (pending_scb_count == 0) 2732 return; 2733 2734 if (ahc_is_paused(ahc)) { 2735 paused = 1; 2736 } else { 2737 paused = 0; 2738 ahc_pause(ahc); 2739 } 2740 2741 saved_scbptr = ahc_inb(ahc, SCBPTR); 2742 /* Ensure that the hscbs down on the card match the new information */ 2743 for (i = 0; i < ahc->scb_data->maxhscbs; i++) { 2744 struct hardware_scb *pending_hscb; 2745 u_int control; 2746 u_int scb_tag; 2747 2748 ahc_outb(ahc, SCBPTR, i); 2749 scb_tag = ahc_inb(ahc, SCB_TAG); 2750 pending_scb = ahc_lookup_scb(ahc, scb_tag); 2751 if (pending_scb == NULL) 2752 continue; 2753 2754 pending_hscb = pending_scb->hscb; 2755 control = ahc_inb(ahc, SCB_CONTROL); 2756 control &= ~(ULTRAENB|MK_MESSAGE); 2757 control |= pending_hscb->control & (ULTRAENB|MK_MESSAGE); 2758 ahc_outb(ahc, SCB_CONTROL, control); 2759 ahc_outb(ahc, SCB_SCSIRATE, pending_hscb->scsirate); 2760 ahc_outb(ahc, SCB_SCSIOFFSET, pending_hscb->scsioffset); 2761 } 2762 ahc_outb(ahc, SCBPTR, saved_scbptr); 2763 2764 if (paused == 0) 2765 ahc_unpause(ahc); 2766} 2767 2768/**************************** Pathing Information *****************************/ 2769static void 2770ahc_fetch_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 2771{ 2772 u_int saved_scsiid; 2773 role_t role; 2774 int our_id; 2775 2776 if (ahc_inb(ahc, SSTAT0) & TARGET) 2777 role = ROLE_TARGET; 2778 else 2779 role = ROLE_INITIATOR; 2780 2781 if (role == ROLE_TARGET 2782 && (ahc->features & AHC_MULTI_TID) != 0 2783 && (ahc_inb(ahc, SEQ_FLAGS) 2784 & (CMDPHASE_PENDING|TARG_CMD_PENDING|NO_DISCONNECT)) != 0) { 2785 /* We were selected, so pull our id from TARGIDIN */ 2786 our_id = ahc_inb(ahc, TARGIDIN) & OID; 2787 } else if ((ahc->features & AHC_ULTRA2) != 0) 2788 our_id = ahc_inb(ahc, SCSIID_ULTRA2) & OID; 2789 else 2790 our_id = ahc_inb(ahc, SCSIID) & OID; 2791 2792 saved_scsiid = ahc_inb(ahc, SAVED_SCSIID); 2793 ahc_compile_devinfo(devinfo, 2794 our_id, 2795 SCSIID_TARGET(ahc, saved_scsiid), 2796 ahc_inb(ahc, SAVED_LUN), 2797 SCSIID_CHANNEL(ahc, saved_scsiid), 2798 role); 2799} 2800 2801static const struct ahc_phase_table_entry* 2802ahc_lookup_phase_entry(int phase) 2803{ 2804 const struct ahc_phase_table_entry *entry; 2805 const struct ahc_phase_table_entry *last_entry; 2806 2807 /* 2808 * num_phases doesn't include the default entry which 2809 * will be returned if the phase doesn't match. 2810 */ 2811 last_entry = &ahc_phase_table[num_phases]; 2812 for (entry = ahc_phase_table; entry < last_entry; entry++) { 2813 if (phase == entry->phase) 2814 break; 2815 } 2816 return (entry); 2817} 2818 2819void 2820ahc_compile_devinfo(struct ahc_devinfo *devinfo, u_int our_id, u_int target, 2821 u_int lun, char channel, role_t role) 2822{ 2823 devinfo->our_scsiid = our_id; 2824 devinfo->target = target; 2825 devinfo->lun = lun; 2826 devinfo->target_offset = target; 2827 devinfo->channel = channel; 2828 devinfo->role = role; 2829 if (channel == 'B') 2830 devinfo->target_offset += 8; 2831 devinfo->target_mask = (0x01 << devinfo->target_offset); 2832} 2833 2834void 2835ahc_print_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 2836{ 2837 printk("%s:%c:%d:%d: ", ahc_name(ahc), devinfo->channel, 2838 devinfo->target, devinfo->lun); 2839} 2840 2841static void 2842ahc_scb_devinfo(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 2843 struct scb *scb) 2844{ 2845 role_t role; 2846 int our_id; 2847 2848 our_id = SCSIID_OUR_ID(scb->hscb->scsiid); 2849 role = ROLE_INITIATOR; 2850 if ((scb->flags & SCB_TARGET_SCB) != 0) 2851 role = ROLE_TARGET; 2852 ahc_compile_devinfo(devinfo, our_id, SCB_GET_TARGET(ahc, scb), 2853 SCB_GET_LUN(scb), SCB_GET_CHANNEL(ahc, scb), role); 2854} 2855 2856 2857/************************ Message Phase Processing ****************************/ 2858static void 2859ahc_assert_atn(struct ahc_softc *ahc) 2860{ 2861 u_int scsisigo; 2862 2863 scsisigo = ATNO; 2864 if ((ahc->features & AHC_DT) == 0) 2865 scsisigo |= ahc_inb(ahc, SCSISIGI); 2866 ahc_outb(ahc, SCSISIGO, scsisigo); 2867} 2868 2869/* 2870 * When an initiator transaction with the MK_MESSAGE flag either reconnects 2871 * or enters the initial message out phase, we are interrupted. Fill our 2872 * outgoing message buffer with the appropriate message and beging handing 2873 * the message phase(s) manually. 2874 */ 2875static void 2876ahc_setup_initiator_msgout(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 2877 struct scb *scb) 2878{ 2879 /* 2880 * To facilitate adding multiple messages together, 2881 * each routine should increment the index and len 2882 * variables instead of setting them explicitly. 2883 */ 2884 ahc->msgout_index = 0; 2885 ahc->msgout_len = 0; 2886 2887 if ((scb->flags & SCB_DEVICE_RESET) == 0 2888 && ahc_inb(ahc, MSG_OUT) == MSG_IDENTIFYFLAG) { 2889 u_int identify_msg; 2890 2891 identify_msg = MSG_IDENTIFYFLAG | SCB_GET_LUN(scb); 2892 if ((scb->hscb->control & DISCENB) != 0) 2893 identify_msg |= MSG_IDENTIFY_DISCFLAG; 2894 ahc->msgout_buf[ahc->msgout_index++] = identify_msg; 2895 ahc->msgout_len++; 2896 2897 if ((scb->hscb->control & TAG_ENB) != 0) { 2898 ahc->msgout_buf[ahc->msgout_index++] = 2899 scb->hscb->control & (TAG_ENB|SCB_TAG_TYPE); 2900 ahc->msgout_buf[ahc->msgout_index++] = scb->hscb->tag; 2901 ahc->msgout_len += 2; 2902 } 2903 } 2904 2905 if (scb->flags & SCB_DEVICE_RESET) { 2906 ahc->msgout_buf[ahc->msgout_index++] = MSG_BUS_DEV_RESET; 2907 ahc->msgout_len++; 2908 ahc_print_path(ahc, scb); 2909 printk("Bus Device Reset Message Sent\n"); 2910 /* 2911 * Clear our selection hardware in advance of 2912 * the busfree. We may have an entry in the waiting 2913 * Q for this target, and we don't want to go about 2914 * selecting while we handle the busfree and blow it 2915 * away. 2916 */ 2917 ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); 2918 } else if ((scb->flags & SCB_ABORT) != 0) { 2919 if ((scb->hscb->control & TAG_ENB) != 0) 2920 ahc->msgout_buf[ahc->msgout_index++] = MSG_ABORT_TAG; 2921 else 2922 ahc->msgout_buf[ahc->msgout_index++] = MSG_ABORT; 2923 ahc->msgout_len++; 2924 ahc_print_path(ahc, scb); 2925 printk("Abort%s Message Sent\n", 2926 (scb->hscb->control & TAG_ENB) != 0 ? " Tag" : ""); 2927 /* 2928 * Clear our selection hardware in advance of 2929 * the busfree. We may have an entry in the waiting 2930 * Q for this target, and we don't want to go about 2931 * selecting while we handle the busfree and blow it 2932 * away. 2933 */ 2934 ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); 2935 } else if ((scb->flags & (SCB_AUTO_NEGOTIATE|SCB_NEGOTIATE)) != 0) { 2936 ahc_build_transfer_msg(ahc, devinfo); 2937 } else { 2938 printk("ahc_intr: AWAITING_MSG for an SCB that " 2939 "does not have a waiting message\n"); 2940 printk("SCSIID = %x, target_mask = %x\n", scb->hscb->scsiid, 2941 devinfo->target_mask); 2942 panic("SCB = %d, SCB Control = %x, MSG_OUT = %x " 2943 "SCB flags = %x", scb->hscb->tag, scb->hscb->control, 2944 ahc_inb(ahc, MSG_OUT), scb->flags); 2945 } 2946 2947 /* 2948 * Clear the MK_MESSAGE flag from the SCB so we aren't 2949 * asked to send this message again. 2950 */ 2951 ahc_outb(ahc, SCB_CONTROL, ahc_inb(ahc, SCB_CONTROL) & ~MK_MESSAGE); 2952 scb->hscb->control &= ~MK_MESSAGE; 2953 ahc->msgout_index = 0; 2954 ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; 2955} 2956 2957/* 2958 * Build an appropriate transfer negotiation message for the 2959 * currently active target. 2960 */ 2961static void 2962ahc_build_transfer_msg(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 2963{ 2964 /* 2965 * We need to initiate transfer negotiations. 2966 * If our current and goal settings are identical, 2967 * we want to renegotiate due to a check condition. 2968 */ 2969 struct ahc_initiator_tinfo *tinfo; 2970 struct ahc_tmode_tstate *tstate; 2971 const struct ahc_syncrate *rate; 2972 int dowide; 2973 int dosync; 2974 int doppr; 2975 u_int period; 2976 u_int ppr_options; 2977 u_int offset; 2978 2979 tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, 2980 devinfo->target, &tstate); 2981 /* 2982 * Filter our period based on the current connection. 2983 * If we can't perform DT transfers on this segment (not in LVD 2984 * mode for instance), then our decision to issue a PPR message 2985 * may change. 2986 */ 2987 period = tinfo->goal.period; 2988 offset = tinfo->goal.offset; 2989 ppr_options = tinfo->goal.ppr_options; 2990 /* Target initiated PPR is not allowed in the SCSI spec */ 2991 if (devinfo->role == ROLE_TARGET) 2992 ppr_options = 0; 2993 rate = ahc_devlimited_syncrate(ahc, tinfo, &period, 2994 &ppr_options, devinfo->role); 2995 dowide = tinfo->curr.width != tinfo->goal.width; 2996 dosync = tinfo->curr.offset != offset || tinfo->curr.period != period; 2997 /* 2998 * Only use PPR if we have options that need it, even if the device 2999 * claims to support it. There might be an expander in the way 3000 * that doesn't. 3001 */ 3002 doppr = ppr_options != 0; 3003 3004 if (!dowide && !dosync && !doppr) { 3005 dowide = tinfo->goal.width != MSG_EXT_WDTR_BUS_8_BIT; 3006 dosync = tinfo->goal.offset != 0; 3007 } 3008 3009 if (!dowide && !dosync && !doppr) { 3010 /* 3011 * Force async with a WDTR message if we have a wide bus, 3012 * or just issue an SDTR with a 0 offset. 3013 */ 3014 if ((ahc->features & AHC_WIDE) != 0) 3015 dowide = 1; 3016 else 3017 dosync = 1; 3018 3019 if (bootverbose) { 3020 ahc_print_devinfo(ahc, devinfo); 3021 printk("Ensuring async\n"); 3022 } 3023 } 3024 3025 /* Target initiated PPR is not allowed in the SCSI spec */ 3026 if (devinfo->role == ROLE_TARGET) 3027 doppr = 0; 3028 3029 /* 3030 * Both the PPR message and SDTR message require the 3031 * goal syncrate to be limited to what the target device 3032 * is capable of handling (based on whether an LVD->SE 3033 * expander is on the bus), so combine these two cases. 3034 * Regardless, guarantee that if we are using WDTR and SDTR 3035 * messages that WDTR comes first. 3036 */ 3037 if (doppr || (dosync && !dowide)) { 3038 3039 offset = tinfo->goal.offset; 3040 ahc_validate_offset(ahc, tinfo, rate, &offset, 3041 doppr ? tinfo->goal.width 3042 : tinfo->curr.width, 3043 devinfo->role); 3044 if (doppr) { 3045 ahc_construct_ppr(ahc, devinfo, period, offset, 3046 tinfo->goal.width, ppr_options); 3047 } else { 3048 ahc_construct_sdtr(ahc, devinfo, period, offset); 3049 } 3050 } else { 3051 ahc_construct_wdtr(ahc, devinfo, tinfo->goal.width); 3052 } 3053} 3054 3055/* 3056 * Build a synchronous negotiation message in our message 3057 * buffer based on the input parameters. 3058 */ 3059static void 3060ahc_construct_sdtr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 3061 u_int period, u_int offset) 3062{ 3063 if (offset == 0) 3064 period = AHC_ASYNC_XFER_PERIOD; 3065 ahc->msgout_index += spi_populate_sync_msg( 3066 ahc->msgout_buf + ahc->msgout_index, period, offset); 3067 ahc->msgout_len += 5; 3068 if (bootverbose) { 3069 printk("(%s:%c:%d:%d): Sending SDTR period %x, offset %x\n", 3070 ahc_name(ahc), devinfo->channel, devinfo->target, 3071 devinfo->lun, period, offset); 3072 } 3073} 3074 3075/* 3076 * Build a wide negotiation message in our message 3077 * buffer based on the input parameters. 3078 */ 3079static void 3080ahc_construct_wdtr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 3081 u_int bus_width) 3082{ 3083 ahc->msgout_index += spi_populate_width_msg( 3084 ahc->msgout_buf + ahc->msgout_index, bus_width); 3085 ahc->msgout_len += 4; 3086 if (bootverbose) { 3087 printk("(%s:%c:%d:%d): Sending WDTR %x\n", 3088 ahc_name(ahc), devinfo->channel, devinfo->target, 3089 devinfo->lun, bus_width); 3090 } 3091} 3092 3093/* 3094 * Build a parallel protocol request message in our message 3095 * buffer based on the input parameters. 3096 */ 3097static void 3098ahc_construct_ppr(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 3099 u_int period, u_int offset, u_int bus_width, 3100 u_int ppr_options) 3101{ 3102 if (offset == 0) 3103 period = AHC_ASYNC_XFER_PERIOD; 3104 ahc->msgout_index += spi_populate_ppr_msg( 3105 ahc->msgout_buf + ahc->msgout_index, period, offset, 3106 bus_width, ppr_options); 3107 ahc->msgout_len += 8; 3108 if (bootverbose) { 3109 printk("(%s:%c:%d:%d): Sending PPR bus_width %x, period %x, " 3110 "offset %x, ppr_options %x\n", ahc_name(ahc), 3111 devinfo->channel, devinfo->target, devinfo->lun, 3112 bus_width, period, offset, ppr_options); 3113 } 3114} 3115 3116/* 3117 * Clear any active message state. 3118 */ 3119static void 3120ahc_clear_msg_state(struct ahc_softc *ahc) 3121{ 3122 ahc->msgout_len = 0; 3123 ahc->msgin_index = 0; 3124 ahc->msg_type = MSG_TYPE_NONE; 3125 if ((ahc_inb(ahc, SCSISIGI) & ATNI) != 0) { 3126 /* 3127 * The target didn't care to respond to our 3128 * message request, so clear ATN. 3129 */ 3130 ahc_outb(ahc, CLRSINT1, CLRATNO); 3131 } 3132 ahc_outb(ahc, MSG_OUT, MSG_NOOP); 3133 ahc_outb(ahc, SEQ_FLAGS2, 3134 ahc_inb(ahc, SEQ_FLAGS2) & ~TARGET_MSG_PENDING); 3135} 3136 3137static void 3138ahc_handle_proto_violation(struct ahc_softc *ahc) 3139{ 3140 struct ahc_devinfo devinfo; 3141 struct scb *scb; 3142 u_int scbid; 3143 u_int seq_flags; 3144 u_int curphase; 3145 u_int lastphase; 3146 int found; 3147 3148 ahc_fetch_devinfo(ahc, &devinfo); 3149 scbid = ahc_inb(ahc, SCB_TAG); 3150 scb = ahc_lookup_scb(ahc, scbid); 3151 seq_flags = ahc_inb(ahc, SEQ_FLAGS); 3152 curphase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; 3153 lastphase = ahc_inb(ahc, LASTPHASE); 3154 if ((seq_flags & NOT_IDENTIFIED) != 0) { 3155 3156 /* 3157 * The reconnecting target either did not send an 3158 * identify message, or did, but we didn't find an SCB 3159 * to match. 3160 */ 3161 ahc_print_devinfo(ahc, &devinfo); 3162 printk("Target did not send an IDENTIFY message. " 3163 "LASTPHASE = 0x%x.\n", lastphase); 3164 scb = NULL; 3165 } else if (scb == NULL) { 3166 /* 3167 * We don't seem to have an SCB active for this 3168 * transaction. Print an error and reset the bus. 3169 */ 3170 ahc_print_devinfo(ahc, &devinfo); 3171 printk("No SCB found during protocol violation\n"); 3172 goto proto_violation_reset; 3173 } else { 3174 ahc_set_transaction_status(scb, CAM_SEQUENCE_FAIL); 3175 if ((seq_flags & NO_CDB_SENT) != 0) { 3176 ahc_print_path(ahc, scb); 3177 printk("No or incomplete CDB sent to device.\n"); 3178 } else if ((ahc_inb(ahc, SCB_CONTROL) & STATUS_RCVD) == 0) { 3179 /* 3180 * The target never bothered to provide status to 3181 * us prior to completing the command. Since we don't 3182 * know the disposition of this command, we must attempt 3183 * to abort it. Assert ATN and prepare to send an abort 3184 * message. 3185 */ 3186 ahc_print_path(ahc, scb); 3187 printk("Completed command without status.\n"); 3188 } else { 3189 ahc_print_path(ahc, scb); 3190 printk("Unknown protocol violation.\n"); 3191 ahc_dump_card_state(ahc); 3192 } 3193 } 3194 if ((lastphase & ~P_DATAIN_DT) == 0 3195 || lastphase == P_COMMAND) { 3196proto_violation_reset: 3197 /* 3198 * Target either went directly to data/command 3199 * phase or didn't respond to our ATN. 3200 * The only safe thing to do is to blow 3201 * it away with a bus reset. 3202 */ 3203 found = ahc_reset_channel(ahc, 'A', TRUE); 3204 printk("%s: Issued Channel %c Bus Reset. " 3205 "%d SCBs aborted\n", ahc_name(ahc), 'A', found); 3206 } else { 3207 /* 3208 * Leave the selection hardware off in case 3209 * this abort attempt will affect yet to 3210 * be sent commands. 3211 */ 3212 ahc_outb(ahc, SCSISEQ, 3213 ahc_inb(ahc, SCSISEQ) & ~ENSELO); 3214 ahc_assert_atn(ahc); 3215 ahc_outb(ahc, MSG_OUT, HOST_MSG); 3216 if (scb == NULL) { 3217 ahc_print_devinfo(ahc, &devinfo); 3218 ahc->msgout_buf[0] = MSG_ABORT_TASK; 3219 ahc->msgout_len = 1; 3220 ahc->msgout_index = 0; 3221 ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; 3222 } else { 3223 ahc_print_path(ahc, scb); 3224 scb->flags |= SCB_ABORT; 3225 } 3226 printk("Protocol violation %s. Attempting to abort.\n", 3227 ahc_lookup_phase_entry(curphase)->phasemsg); 3228 } 3229} 3230 3231/* 3232 * Manual message loop handler. 3233 */ 3234static void 3235ahc_handle_message_phase(struct ahc_softc *ahc) 3236{ 3237 struct ahc_devinfo devinfo; 3238 u_int bus_phase; 3239 int end_session; 3240 3241 ahc_fetch_devinfo(ahc, &devinfo); 3242 end_session = FALSE; 3243 bus_phase = ahc_inb(ahc, SCSISIGI) & PHASE_MASK; 3244 3245reswitch: 3246 switch (ahc->msg_type) { 3247 case MSG_TYPE_INITIATOR_MSGOUT: 3248 { 3249 int lastbyte; 3250 int phasemis; 3251 int msgdone; 3252 3253 if (ahc->msgout_len == 0) 3254 panic("HOST_MSG_LOOP interrupt with no active message"); 3255 3256#ifdef AHC_DEBUG 3257 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { 3258 ahc_print_devinfo(ahc, &devinfo); 3259 printk("INITIATOR_MSG_OUT"); 3260 } 3261#endif 3262 phasemis = bus_phase != P_MESGOUT; 3263 if (phasemis) { 3264#ifdef AHC_DEBUG 3265 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { 3266 printk(" PHASEMIS %s\n", 3267 ahc_lookup_phase_entry(bus_phase) 3268 ->phasemsg); 3269 } 3270#endif 3271 if (bus_phase == P_MESGIN) { 3272 /* 3273 * Change gears and see if 3274 * this messages is of interest to 3275 * us or should be passed back to 3276 * the sequencer. 3277 */ 3278 ahc_outb(ahc, CLRSINT1, CLRATNO); 3279 ahc->send_msg_perror = FALSE; 3280 ahc->msg_type = MSG_TYPE_INITIATOR_MSGIN; 3281 ahc->msgin_index = 0; 3282 goto reswitch; 3283 } 3284 end_session = TRUE; 3285 break; 3286 } 3287 3288 if (ahc->send_msg_perror) { 3289 ahc_outb(ahc, CLRSINT1, CLRATNO); 3290 ahc_outb(ahc, CLRSINT1, CLRREQINIT); 3291#ifdef AHC_DEBUG 3292 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) 3293 printk(" byte 0x%x\n", ahc->send_msg_perror); 3294#endif 3295 ahc_outb(ahc, SCSIDATL, MSG_PARITY_ERROR); 3296 break; 3297 } 3298 3299 msgdone = ahc->msgout_index == ahc->msgout_len; 3300 if (msgdone) { 3301 /* 3302 * The target has requested a retry. 3303 * Re-assert ATN, reset our message index to 3304 * 0, and try again. 3305 */ 3306 ahc->msgout_index = 0; 3307 ahc_assert_atn(ahc); 3308 } 3309 3310 lastbyte = ahc->msgout_index == (ahc->msgout_len - 1); 3311 if (lastbyte) { 3312 /* Last byte is signified by dropping ATN */ 3313 ahc_outb(ahc, CLRSINT1, CLRATNO); 3314 } 3315 3316 /* 3317 * Clear our interrupt status and present 3318 * the next byte on the bus. 3319 */ 3320 ahc_outb(ahc, CLRSINT1, CLRREQINIT); 3321#ifdef AHC_DEBUG 3322 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) 3323 printk(" byte 0x%x\n", 3324 ahc->msgout_buf[ahc->msgout_index]); 3325#endif 3326 ahc_outb(ahc, SCSIDATL, ahc->msgout_buf[ahc->msgout_index++]); 3327 break; 3328 } 3329 case MSG_TYPE_INITIATOR_MSGIN: 3330 { 3331 int phasemis; 3332 int message_done; 3333 3334#ifdef AHC_DEBUG 3335 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { 3336 ahc_print_devinfo(ahc, &devinfo); 3337 printk("INITIATOR_MSG_IN"); 3338 } 3339#endif 3340 phasemis = bus_phase != P_MESGIN; 3341 if (phasemis) { 3342#ifdef AHC_DEBUG 3343 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { 3344 printk(" PHASEMIS %s\n", 3345 ahc_lookup_phase_entry(bus_phase) 3346 ->phasemsg); 3347 } 3348#endif 3349 ahc->msgin_index = 0; 3350 if (bus_phase == P_MESGOUT 3351 && (ahc->send_msg_perror == TRUE 3352 || (ahc->msgout_len != 0 3353 && ahc->msgout_index == 0))) { 3354 ahc->msg_type = MSG_TYPE_INITIATOR_MSGOUT; 3355 goto reswitch; 3356 } 3357 end_session = TRUE; 3358 break; 3359 } 3360 3361 /* Pull the byte in without acking it */ 3362 ahc->msgin_buf[ahc->msgin_index] = ahc_inb(ahc, SCSIBUSL); 3363#ifdef AHC_DEBUG 3364 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) 3365 printk(" byte 0x%x\n", 3366 ahc->msgin_buf[ahc->msgin_index]); 3367#endif 3368 3369 message_done = ahc_parse_msg(ahc, &devinfo); 3370 3371 if (message_done) { 3372 /* 3373 * Clear our incoming message buffer in case there 3374 * is another message following this one. 3375 */ 3376 ahc->msgin_index = 0; 3377 3378 /* 3379 * If this message illicited a response, 3380 * assert ATN so the target takes us to the 3381 * message out phase. 3382 */ 3383 if (ahc->msgout_len != 0) { 3384#ifdef AHC_DEBUG 3385 if ((ahc_debug & AHC_SHOW_MESSAGES) != 0) { 3386 ahc_print_devinfo(ahc, &devinfo); 3387 printk("Asserting ATN for response\n"); 3388 } 3389#endif 3390 ahc_assert_atn(ahc); 3391 } 3392 } else 3393 ahc->msgin_index++; 3394 3395 if (message_done == MSGLOOP_TERMINATED) { 3396 end_session = TRUE; 3397 } else { 3398 /* Ack the byte */ 3399 ahc_outb(ahc, CLRSINT1, CLRREQINIT); 3400 ahc_inb(ahc, SCSIDATL); 3401 } 3402 break; 3403 } 3404 case MSG_TYPE_TARGET_MSGIN: 3405 { 3406 int msgdone; 3407 int msgout_request; 3408 3409 if (ahc->msgout_len == 0) 3410 panic("Target MSGIN with no active message"); 3411 3412 /* 3413 * If we interrupted a mesgout session, the initiator 3414 * will not know this until our first REQ. So, we 3415 * only honor mesgout requests after we've sent our 3416 * first byte. 3417 */ 3418 if ((ahc_inb(ahc, SCSISIGI) & ATNI) != 0 3419 && ahc->msgout_index > 0) 3420 msgout_request = TRUE; 3421 else 3422 msgout_request = FALSE; 3423 3424 if (msgout_request) { 3425 3426 /* 3427 * Change gears and see if 3428 * this messages is of interest to 3429 * us or should be passed back to 3430 * the sequencer. 3431 */ 3432 ahc->msg_type = MSG_TYPE_TARGET_MSGOUT; 3433 ahc_outb(ahc, SCSISIGO, P_MESGOUT | BSYO); 3434 ahc->msgin_index = 0; 3435 /* Dummy read to REQ for first byte */ 3436 ahc_inb(ahc, SCSIDATL); 3437 ahc_outb(ahc, SXFRCTL0, 3438 ahc_inb(ahc, SXFRCTL0) | SPIOEN); 3439 break; 3440 } 3441 3442 msgdone = ahc->msgout_index == ahc->msgout_len; 3443 if (msgdone) { 3444 ahc_outb(ahc, SXFRCTL0, 3445 ahc_inb(ahc, SXFRCTL0) & ~SPIOEN); 3446 end_session = TRUE; 3447 break; 3448 } 3449 3450 /* 3451 * Present the next byte on the bus. 3452 */ 3453 ahc_outb(ahc, SXFRCTL0, ahc_inb(ahc, SXFRCTL0) | SPIOEN); 3454 ahc_outb(ahc, SCSIDATL, ahc->msgout_buf[ahc->msgout_index++]); 3455 break; 3456 } 3457 case MSG_TYPE_TARGET_MSGOUT: 3458 { 3459 int lastbyte; 3460 int msgdone; 3461 3462 /* 3463 * The initiator signals that this is 3464 * the last byte by dropping ATN. 3465 */ 3466 lastbyte = (ahc_inb(ahc, SCSISIGI) & ATNI) == 0; 3467 3468 /* 3469 * Read the latched byte, but turn off SPIOEN first 3470 * so that we don't inadvertently cause a REQ for the 3471 * next byte. 3472 */ 3473 ahc_outb(ahc, SXFRCTL0, ahc_inb(ahc, SXFRCTL0) & ~SPIOEN); 3474 ahc->msgin_buf[ahc->msgin_index] = ahc_inb(ahc, SCSIDATL); 3475 msgdone = ahc_parse_msg(ahc, &devinfo); 3476 if (msgdone == MSGLOOP_TERMINATED) { 3477 /* 3478 * The message is *really* done in that it caused 3479 * us to go to bus free. The sequencer has already 3480 * been reset at this point, so pull the ejection 3481 * handle. 3482 */ 3483 return; 3484 } 3485 3486 ahc->msgin_index++; 3487 3488 /* 3489 * XXX Read spec about initiator dropping ATN too soon 3490 * and use msgdone to detect it. 3491 */ 3492 if (msgdone == MSGLOOP_MSGCOMPLETE) { 3493 ahc->msgin_index = 0; 3494 3495 /* 3496 * If this message illicited a response, transition 3497 * to the Message in phase and send it. 3498 */ 3499 if (ahc->msgout_len != 0) { 3500 ahc_outb(ahc, SCSISIGO, P_MESGIN | BSYO); 3501 ahc_outb(ahc, SXFRCTL0, 3502 ahc_inb(ahc, SXFRCTL0) | SPIOEN); 3503 ahc->msg_type = MSG_TYPE_TARGET_MSGIN; 3504 ahc->msgin_index = 0; 3505 break; 3506 } 3507 } 3508 3509 if (lastbyte) 3510 end_session = TRUE; 3511 else { 3512 /* Ask for the next byte. */ 3513 ahc_outb(ahc, SXFRCTL0, 3514 ahc_inb(ahc, SXFRCTL0) | SPIOEN); 3515 } 3516 3517 break; 3518 } 3519 default: 3520 panic("Unknown REQINIT message type"); 3521 } 3522 3523 if (end_session) { 3524 ahc_clear_msg_state(ahc); 3525 ahc_outb(ahc, RETURN_1, EXIT_MSG_LOOP); 3526 } else 3527 ahc_outb(ahc, RETURN_1, CONT_MSG_LOOP); 3528} 3529 3530/* 3531 * See if we sent a particular extended message to the target. 3532 * If "full" is true, return true only if the target saw the full 3533 * message. If "full" is false, return true if the target saw at 3534 * least the first byte of the message. 3535 */ 3536static int 3537ahc_sent_msg(struct ahc_softc *ahc, ahc_msgtype type, u_int msgval, int full) 3538{ 3539 int found; 3540 u_int index; 3541 3542 found = FALSE; 3543 index = 0; 3544 3545 while (index < ahc->msgout_len) { 3546 if (ahc->msgout_buf[index] == MSG_EXTENDED) { 3547 u_int end_index; 3548 3549 end_index = index + 1 + ahc->msgout_buf[index + 1]; 3550 if (ahc->msgout_buf[index+2] == msgval 3551 && type == AHCMSG_EXT) { 3552 3553 if (full) { 3554 if (ahc->msgout_index > end_index) 3555 found = TRUE; 3556 } else if (ahc->msgout_index > index) 3557 found = TRUE; 3558 } 3559 index = end_index; 3560 } else if (ahc->msgout_buf[index] >= MSG_SIMPLE_TASK 3561 && ahc->msgout_buf[index] <= MSG_IGN_WIDE_RESIDUE) { 3562 3563 /* Skip tag type and tag id or residue param*/ 3564 index += 2; 3565 } else { 3566 /* Single byte message */ 3567 if (type == AHCMSG_1B 3568 && ahc->msgout_buf[index] == msgval 3569 && ahc->msgout_index > index) 3570 found = TRUE; 3571 index++; 3572 } 3573 3574 if (found) 3575 break; 3576 } 3577 return (found); 3578} 3579 3580/* 3581 * Wait for a complete incoming message, parse it, and respond accordingly. 3582 */ 3583static int 3584ahc_parse_msg(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 3585{ 3586 struct ahc_initiator_tinfo *tinfo; 3587 struct ahc_tmode_tstate *tstate; 3588 int reject; 3589 int done; 3590 int response; 3591 u_int targ_scsirate; 3592 3593 done = MSGLOOP_IN_PROG; 3594 response = FALSE; 3595 reject = FALSE; 3596 tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, devinfo->our_scsiid, 3597 devinfo->target, &tstate); 3598 targ_scsirate = tinfo->scsirate; 3599 3600 /* 3601 * Parse as much of the message as is available, 3602 * rejecting it if we don't support it. When 3603 * the entire message is available and has been 3604 * handled, return MSGLOOP_MSGCOMPLETE, indicating 3605 * that we have parsed an entire message. 3606 * 3607 * In the case of extended messages, we accept the length 3608 * byte outright and perform more checking once we know the 3609 * extended message type. 3610 */ 3611 switch (ahc->msgin_buf[0]) { 3612 case MSG_DISCONNECT: 3613 case MSG_SAVEDATAPOINTER: 3614 case MSG_CMDCOMPLETE: 3615 case MSG_RESTOREPOINTERS: 3616 case MSG_IGN_WIDE_RESIDUE: 3617 /* 3618 * End our message loop as these are messages 3619 * the sequencer handles on its own. 3620 */ 3621 done = MSGLOOP_TERMINATED; 3622 break; 3623 case MSG_MESSAGE_REJECT: 3624 response = ahc_handle_msg_reject(ahc, devinfo); 3625 /* FALLTHROUGH */ 3626 case MSG_NOOP: 3627 done = MSGLOOP_MSGCOMPLETE; 3628 break; 3629 case MSG_EXTENDED: 3630 { 3631 /* Wait for enough of the message to begin validation */ 3632 if (ahc->msgin_index < 2) 3633 break; 3634 switch (ahc->msgin_buf[2]) { 3635 case MSG_EXT_SDTR: 3636 { 3637 const struct ahc_syncrate *syncrate; 3638 u_int period; 3639 u_int ppr_options; 3640 u_int offset; 3641 u_int saved_offset; 3642 3643 if (ahc->msgin_buf[1] != MSG_EXT_SDTR_LEN) { 3644 reject = TRUE; 3645 break; 3646 } 3647 3648 /* 3649 * Wait until we have both args before validating 3650 * and acting on this message. 3651 * 3652 * Add one to MSG_EXT_SDTR_LEN to account for 3653 * the extended message preamble. 3654 */ 3655 if (ahc->msgin_index < (MSG_EXT_SDTR_LEN + 1)) 3656 break; 3657 3658 period = ahc->msgin_buf[3]; 3659 ppr_options = 0; 3660 saved_offset = offset = ahc->msgin_buf[4]; 3661 syncrate = ahc_devlimited_syncrate(ahc, tinfo, &period, 3662 &ppr_options, 3663 devinfo->role); 3664 ahc_validate_offset(ahc, tinfo, syncrate, &offset, 3665 targ_scsirate & WIDEXFER, 3666 devinfo->role); 3667 if (bootverbose) { 3668 printk("(%s:%c:%d:%d): Received " 3669 "SDTR period %x, offset %x\n\t" 3670 "Filtered to period %x, offset %x\n", 3671 ahc_name(ahc), devinfo->channel, 3672 devinfo->target, devinfo->lun, 3673 ahc->msgin_buf[3], saved_offset, 3674 period, offset); 3675 } 3676 ahc_set_syncrate(ahc, devinfo, 3677 syncrate, period, 3678 offset, ppr_options, 3679 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 3680 /*paused*/TRUE); 3681 3682 /* 3683 * See if we initiated Sync Negotiation 3684 * and didn't have to fall down to async 3685 * transfers. 3686 */ 3687 if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_SDTR, TRUE)) { 3688 /* We started it */ 3689 if (saved_offset != offset) { 3690 /* Went too low - force async */ 3691 reject = TRUE; 3692 } 3693 } else { 3694 /* 3695 * Send our own SDTR in reply 3696 */ 3697 if (bootverbose 3698 && devinfo->role == ROLE_INITIATOR) { 3699 printk("(%s:%c:%d:%d): Target " 3700 "Initiated SDTR\n", 3701 ahc_name(ahc), devinfo->channel, 3702 devinfo->target, devinfo->lun); 3703 } 3704 ahc->msgout_index = 0; 3705 ahc->msgout_len = 0; 3706 ahc_construct_sdtr(ahc, devinfo, 3707 period, offset); 3708 ahc->msgout_index = 0; 3709 response = TRUE; 3710 } 3711 done = MSGLOOP_MSGCOMPLETE; 3712 break; 3713 } 3714 case MSG_EXT_WDTR: 3715 { 3716 u_int bus_width; 3717 u_int saved_width; 3718 u_int sending_reply; 3719 3720 sending_reply = FALSE; 3721 if (ahc->msgin_buf[1] != MSG_EXT_WDTR_LEN) { 3722 reject = TRUE; 3723 break; 3724 } 3725 3726 /* 3727 * Wait until we have our arg before validating 3728 * and acting on this message. 3729 * 3730 * Add one to MSG_EXT_WDTR_LEN to account for 3731 * the extended message preamble. 3732 */ 3733 if (ahc->msgin_index < (MSG_EXT_WDTR_LEN + 1)) 3734 break; 3735 3736 bus_width = ahc->msgin_buf[3]; 3737 saved_width = bus_width; 3738 ahc_validate_width(ahc, tinfo, &bus_width, 3739 devinfo->role); 3740 if (bootverbose) { 3741 printk("(%s:%c:%d:%d): Received WDTR " 3742 "%x filtered to %x\n", 3743 ahc_name(ahc), devinfo->channel, 3744 devinfo->target, devinfo->lun, 3745 saved_width, bus_width); 3746 } 3747 3748 if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_WDTR, TRUE)) { 3749 /* 3750 * Don't send a WDTR back to the 3751 * target, since we asked first. 3752 * If the width went higher than our 3753 * request, reject it. 3754 */ 3755 if (saved_width > bus_width) { 3756 reject = TRUE; 3757 printk("(%s:%c:%d:%d): requested %dBit " 3758 "transfers. Rejecting...\n", 3759 ahc_name(ahc), devinfo->channel, 3760 devinfo->target, devinfo->lun, 3761 8 * (0x01 << bus_width)); 3762 bus_width = 0; 3763 } 3764 } else { 3765 /* 3766 * Send our own WDTR in reply 3767 */ 3768 if (bootverbose 3769 && devinfo->role == ROLE_INITIATOR) { 3770 printk("(%s:%c:%d:%d): Target " 3771 "Initiated WDTR\n", 3772 ahc_name(ahc), devinfo->channel, 3773 devinfo->target, devinfo->lun); 3774 } 3775 ahc->msgout_index = 0; 3776 ahc->msgout_len = 0; 3777 ahc_construct_wdtr(ahc, devinfo, bus_width); 3778 ahc->msgout_index = 0; 3779 response = TRUE; 3780 sending_reply = TRUE; 3781 } 3782 /* 3783 * After a wide message, we are async, but 3784 * some devices don't seem to honor this portion 3785 * of the spec. Force a renegotiation of the 3786 * sync component of our transfer agreement even 3787 * if our goal is async. By updating our width 3788 * after forcing the negotiation, we avoid 3789 * renegotiating for width. 3790 */ 3791 ahc_update_neg_request(ahc, devinfo, tstate, 3792 tinfo, AHC_NEG_ALWAYS); 3793 ahc_set_width(ahc, devinfo, bus_width, 3794 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 3795 /*paused*/TRUE); 3796 if (sending_reply == FALSE && reject == FALSE) { 3797 3798 /* 3799 * We will always have an SDTR to send. 3800 */ 3801 ahc->msgout_index = 0; 3802 ahc->msgout_len = 0; 3803 ahc_build_transfer_msg(ahc, devinfo); 3804 ahc->msgout_index = 0; 3805 response = TRUE; 3806 } 3807 done = MSGLOOP_MSGCOMPLETE; 3808 break; 3809 } 3810 case MSG_EXT_PPR: 3811 { 3812 const struct ahc_syncrate *syncrate; 3813 u_int period; 3814 u_int offset; 3815 u_int bus_width; 3816 u_int ppr_options; 3817 u_int saved_width; 3818 u_int saved_offset; 3819 u_int saved_ppr_options; 3820 3821 if (ahc->msgin_buf[1] != MSG_EXT_PPR_LEN) { 3822 reject = TRUE; 3823 break; 3824 } 3825 3826 /* 3827 * Wait until we have all args before validating 3828 * and acting on this message. 3829 * 3830 * Add one to MSG_EXT_PPR_LEN to account for 3831 * the extended message preamble. 3832 */ 3833 if (ahc->msgin_index < (MSG_EXT_PPR_LEN + 1)) 3834 break; 3835 3836 period = ahc->msgin_buf[3]; 3837 offset = ahc->msgin_buf[5]; 3838 bus_width = ahc->msgin_buf[6]; 3839 saved_width = bus_width; 3840 ppr_options = ahc->msgin_buf[7]; 3841 /* 3842 * According to the spec, a DT only 3843 * period factor with no DT option 3844 * set implies async. 3845 */ 3846 if ((ppr_options & MSG_EXT_PPR_DT_REQ) == 0 3847 && period == 9) 3848 offset = 0; 3849 saved_ppr_options = ppr_options; 3850 saved_offset = offset; 3851 3852 /* 3853 * Mask out any options we don't support 3854 * on any controller. Transfer options are 3855 * only available if we are negotiating wide. 3856 */ 3857 ppr_options &= MSG_EXT_PPR_DT_REQ; 3858 if (bus_width == 0) 3859 ppr_options = 0; 3860 3861 ahc_validate_width(ahc, tinfo, &bus_width, 3862 devinfo->role); 3863 syncrate = ahc_devlimited_syncrate(ahc, tinfo, &period, 3864 &ppr_options, 3865 devinfo->role); 3866 ahc_validate_offset(ahc, tinfo, syncrate, 3867 &offset, bus_width, 3868 devinfo->role); 3869 3870 if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_PPR, TRUE)) { 3871 /* 3872 * If we are unable to do any of the 3873 * requested options (we went too low), 3874 * then we'll have to reject the message. 3875 */ 3876 if (saved_width > bus_width 3877 || saved_offset != offset 3878 || saved_ppr_options != ppr_options) { 3879 reject = TRUE; 3880 period = 0; 3881 offset = 0; 3882 bus_width = 0; 3883 ppr_options = 0; 3884 syncrate = NULL; 3885 } 3886 } else { 3887 if (devinfo->role != ROLE_TARGET) 3888 printk("(%s:%c:%d:%d): Target " 3889 "Initiated PPR\n", 3890 ahc_name(ahc), devinfo->channel, 3891 devinfo->target, devinfo->lun); 3892 else 3893 printk("(%s:%c:%d:%d): Initiator " 3894 "Initiated PPR\n", 3895 ahc_name(ahc), devinfo->channel, 3896 devinfo->target, devinfo->lun); 3897 ahc->msgout_index = 0; 3898 ahc->msgout_len = 0; 3899 ahc_construct_ppr(ahc, devinfo, period, offset, 3900 bus_width, ppr_options); 3901 ahc->msgout_index = 0; 3902 response = TRUE; 3903 } 3904 if (bootverbose) { 3905 printk("(%s:%c:%d:%d): Received PPR width %x, " 3906 "period %x, offset %x,options %x\n" 3907 "\tFiltered to width %x, period %x, " 3908 "offset %x, options %x\n", 3909 ahc_name(ahc), devinfo->channel, 3910 devinfo->target, devinfo->lun, 3911 saved_width, ahc->msgin_buf[3], 3912 saved_offset, saved_ppr_options, 3913 bus_width, period, offset, ppr_options); 3914 } 3915 ahc_set_width(ahc, devinfo, bus_width, 3916 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 3917 /*paused*/TRUE); 3918 ahc_set_syncrate(ahc, devinfo, 3919 syncrate, period, 3920 offset, ppr_options, 3921 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 3922 /*paused*/TRUE); 3923 done = MSGLOOP_MSGCOMPLETE; 3924 break; 3925 } 3926 default: 3927 /* Unknown extended message. Reject it. */ 3928 reject = TRUE; 3929 break; 3930 } 3931 break; 3932 } 3933#ifdef AHC_TARGET_MODE 3934 case MSG_BUS_DEV_RESET: 3935 ahc_handle_devreset(ahc, devinfo, 3936 CAM_BDR_SENT, 3937 "Bus Device Reset Received", 3938 /*verbose_level*/0); 3939 ahc_restart(ahc); 3940 done = MSGLOOP_TERMINATED; 3941 break; 3942 case MSG_ABORT_TAG: 3943 case MSG_ABORT: 3944 case MSG_CLEAR_QUEUE: 3945 { 3946 int tag; 3947 3948 /* Target mode messages */ 3949 if (devinfo->role != ROLE_TARGET) { 3950 reject = TRUE; 3951 break; 3952 } 3953 tag = SCB_LIST_NULL; 3954 if (ahc->msgin_buf[0] == MSG_ABORT_TAG) 3955 tag = ahc_inb(ahc, INITIATOR_TAG); 3956 ahc_abort_scbs(ahc, devinfo->target, devinfo->channel, 3957 devinfo->lun, tag, ROLE_TARGET, 3958 CAM_REQ_ABORTED); 3959 3960 tstate = ahc->enabled_targets[devinfo->our_scsiid]; 3961 if (tstate != NULL) { 3962 struct ahc_tmode_lstate* lstate; 3963 3964 lstate = tstate->enabled_luns[devinfo->lun]; 3965 if (lstate != NULL) { 3966 ahc_queue_lstate_event(ahc, lstate, 3967 devinfo->our_scsiid, 3968 ahc->msgin_buf[0], 3969 /*arg*/tag); 3970 ahc_send_lstate_events(ahc, lstate); 3971 } 3972 } 3973 ahc_restart(ahc); 3974 done = MSGLOOP_TERMINATED; 3975 break; 3976 } 3977#endif 3978 case MSG_TERM_IO_PROC: 3979 default: 3980 reject = TRUE; 3981 break; 3982 } 3983 3984 if (reject) { 3985 /* 3986 * Setup to reject the message. 3987 */ 3988 ahc->msgout_index = 0; 3989 ahc->msgout_len = 1; 3990 ahc->msgout_buf[0] = MSG_MESSAGE_REJECT; 3991 done = MSGLOOP_MSGCOMPLETE; 3992 response = TRUE; 3993 } 3994 3995 if (done != MSGLOOP_IN_PROG && !response) 3996 /* Clear the outgoing message buffer */ 3997 ahc->msgout_len = 0; 3998 3999 return (done); 4000} 4001 4002/* 4003 * Process a message reject message. 4004 */ 4005static int 4006ahc_handle_msg_reject(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 4007{ 4008 /* 4009 * What we care about here is if we had an 4010 * outstanding SDTR or WDTR message for this 4011 * target. If we did, this is a signal that 4012 * the target is refusing negotiation. 4013 */ 4014 struct scb *scb; 4015 struct ahc_initiator_tinfo *tinfo; 4016 struct ahc_tmode_tstate *tstate; 4017 u_int scb_index; 4018 u_int last_msg; 4019 int response = 0; 4020 4021 scb_index = ahc_inb(ahc, SCB_TAG); 4022 scb = ahc_lookup_scb(ahc, scb_index); 4023 tinfo = ahc_fetch_transinfo(ahc, devinfo->channel, 4024 devinfo->our_scsiid, 4025 devinfo->target, &tstate); 4026 /* Might be necessary */ 4027 last_msg = ahc_inb(ahc, LAST_MSG); 4028 4029 if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_PPR, /*full*/FALSE)) { 4030 /* 4031 * Target does not support the PPR message. 4032 * Attempt to negotiate SPI-2 style. 4033 */ 4034 if (bootverbose) { 4035 printk("(%s:%c:%d:%d): PPR Rejected. " 4036 "Trying WDTR/SDTR\n", 4037 ahc_name(ahc), devinfo->channel, 4038 devinfo->target, devinfo->lun); 4039 } 4040 tinfo->goal.ppr_options = 0; 4041 tinfo->curr.transport_version = 2; 4042 tinfo->goal.transport_version = 2; 4043 ahc->msgout_index = 0; 4044 ahc->msgout_len = 0; 4045 ahc_build_transfer_msg(ahc, devinfo); 4046 ahc->msgout_index = 0; 4047 response = 1; 4048 } else if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_WDTR, /*full*/FALSE)) { 4049 4050 /* note 8bit xfers */ 4051 printk("(%s:%c:%d:%d): refuses WIDE negotiation. Using " 4052 "8bit transfers\n", ahc_name(ahc), 4053 devinfo->channel, devinfo->target, devinfo->lun); 4054 ahc_set_width(ahc, devinfo, MSG_EXT_WDTR_BUS_8_BIT, 4055 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 4056 /*paused*/TRUE); 4057 /* 4058 * No need to clear the sync rate. If the target 4059 * did not accept the command, our syncrate is 4060 * unaffected. If the target started the negotiation, 4061 * but rejected our response, we already cleared the 4062 * sync rate before sending our WDTR. 4063 */ 4064 if (tinfo->goal.offset != tinfo->curr.offset) { 4065 4066 /* Start the sync negotiation */ 4067 ahc->msgout_index = 0; 4068 ahc->msgout_len = 0; 4069 ahc_build_transfer_msg(ahc, devinfo); 4070 ahc->msgout_index = 0; 4071 response = 1; 4072 } 4073 } else if (ahc_sent_msg(ahc, AHCMSG_EXT, MSG_EXT_SDTR, /*full*/FALSE)) { 4074 /* note asynch xfers and clear flag */ 4075 ahc_set_syncrate(ahc, devinfo, /*syncrate*/NULL, /*period*/0, 4076 /*offset*/0, /*ppr_options*/0, 4077 AHC_TRANS_ACTIVE|AHC_TRANS_GOAL, 4078 /*paused*/TRUE); 4079 printk("(%s:%c:%d:%d): refuses synchronous negotiation. " 4080 "Using asynchronous transfers\n", 4081 ahc_name(ahc), devinfo->channel, 4082 devinfo->target, devinfo->lun); 4083 } else if ((scb->hscb->control & MSG_SIMPLE_TASK) != 0) { 4084 int tag_type; 4085 int mask; 4086 4087 tag_type = (scb->hscb->control & MSG_SIMPLE_TASK); 4088 4089 if (tag_type == MSG_SIMPLE_TASK) { 4090 printk("(%s:%c:%d:%d): refuses tagged commands. " 4091 "Performing non-tagged I/O\n", ahc_name(ahc), 4092 devinfo->channel, devinfo->target, devinfo->lun); 4093 ahc_set_tags(ahc, scb->io_ctx, devinfo, AHC_QUEUE_NONE); 4094 mask = ~0x23; 4095 } else { 4096 printk("(%s:%c:%d:%d): refuses %s tagged commands. " 4097 "Performing simple queue tagged I/O only\n", 4098 ahc_name(ahc), devinfo->channel, devinfo->target, 4099 devinfo->lun, tag_type == MSG_ORDERED_TASK 4100 ? "ordered" : "head of queue"); 4101 ahc_set_tags(ahc, scb->io_ctx, devinfo, AHC_QUEUE_BASIC); 4102 mask = ~0x03; 4103 } 4104 4105 /* 4106 * Resend the identify for this CCB as the target 4107 * may believe that the selection is invalid otherwise. 4108 */ 4109 ahc_outb(ahc, SCB_CONTROL, 4110 ahc_inb(ahc, SCB_CONTROL) & mask); 4111 scb->hscb->control &= mask; 4112 ahc_set_transaction_tag(scb, /*enabled*/FALSE, 4113 /*type*/MSG_SIMPLE_TASK); 4114 ahc_outb(ahc, MSG_OUT, MSG_IDENTIFYFLAG); 4115 ahc_assert_atn(ahc); 4116 4117 /* 4118 * This transaction is now at the head of 4119 * the untagged queue for this target. 4120 */ 4121 if ((ahc->flags & AHC_SCB_BTT) == 0) { 4122 struct scb_tailq *untagged_q; 4123 4124 untagged_q = 4125 &(ahc->untagged_queues[devinfo->target_offset]); 4126 TAILQ_INSERT_HEAD(untagged_q, scb, links.tqe); 4127 scb->flags |= SCB_UNTAGGEDQ; 4128 } 4129 ahc_busy_tcl(ahc, BUILD_TCL(scb->hscb->scsiid, devinfo->lun), 4130 scb->hscb->tag); 4131 4132 /* 4133 * Requeue all tagged commands for this target 4134 * currently in our possession so they can be 4135 * converted to untagged commands. 4136 */ 4137 ahc_search_qinfifo(ahc, SCB_GET_TARGET(ahc, scb), 4138 SCB_GET_CHANNEL(ahc, scb), 4139 SCB_GET_LUN(scb), /*tag*/SCB_LIST_NULL, 4140 ROLE_INITIATOR, CAM_REQUEUE_REQ, 4141 SEARCH_COMPLETE); 4142 } else { 4143 /* 4144 * Otherwise, we ignore it. 4145 */ 4146 printk("%s:%c:%d: Message reject for %x -- ignored\n", 4147 ahc_name(ahc), devinfo->channel, devinfo->target, 4148 last_msg); 4149 } 4150 return (response); 4151} 4152 4153/* 4154 * Process an ingnore wide residue message. 4155 */ 4156static void 4157ahc_handle_ign_wide_residue(struct ahc_softc *ahc, struct ahc_devinfo *devinfo) 4158{ 4159 u_int scb_index; 4160 struct scb *scb; 4161 4162 scb_index = ahc_inb(ahc, SCB_TAG); 4163 scb = ahc_lookup_scb(ahc, scb_index); 4164 /* 4165 * XXX Actually check data direction in the sequencer? 4166 * Perhaps add datadir to some spare bits in the hscb? 4167 */ 4168 if ((ahc_inb(ahc, SEQ_FLAGS) & DPHASE) == 0 4169 || ahc_get_transfer_dir(scb) != CAM_DIR_IN) { 4170 /* 4171 * Ignore the message if we haven't 4172 * seen an appropriate data phase yet. 4173 */ 4174 } else { 4175 /* 4176 * If the residual occurred on the last 4177 * transfer and the transfer request was 4178 * expected to end on an odd count, do 4179 * nothing. Otherwise, subtract a byte 4180 * and update the residual count accordingly. 4181 */ 4182 uint32_t sgptr; 4183 4184 sgptr = ahc_inb(ahc, SCB_RESIDUAL_SGPTR); 4185 if ((sgptr & SG_LIST_NULL) != 0 4186 && (ahc_inb(ahc, SCB_LUN) & SCB_XFERLEN_ODD) != 0) { 4187 /* 4188 * If the residual occurred on the last 4189 * transfer and the transfer request was 4190 * expected to end on an odd count, do 4191 * nothing. 4192 */ 4193 } else { 4194 struct ahc_dma_seg *sg; 4195 uint32_t data_cnt; 4196 uint32_t data_addr; 4197 uint32_t sglen; 4198 4199 /* Pull in all of the sgptr */ 4200 sgptr = ahc_inl(ahc, SCB_RESIDUAL_SGPTR); 4201 data_cnt = ahc_inl(ahc, SCB_RESIDUAL_DATACNT); 4202 4203 if ((sgptr & SG_LIST_NULL) != 0) { 4204 /* 4205 * The residual data count is not updated 4206 * for the command run to completion case. 4207 * Explicitly zero the count. 4208 */ 4209 data_cnt &= ~AHC_SG_LEN_MASK; 4210 } 4211 4212 data_addr = ahc_inl(ahc, SHADDR); 4213 4214 data_cnt += 1; 4215 data_addr -= 1; 4216 sgptr &= SG_PTR_MASK; 4217 4218 sg = ahc_sg_bus_to_virt(scb, sgptr); 4219 4220 /* 4221 * The residual sg ptr points to the next S/G 4222 * to load so we must go back one. 4223 */ 4224 sg--; 4225 sglen = ahc_le32toh(sg->len) & AHC_SG_LEN_MASK; 4226 if (sg != scb->sg_list 4227 && sglen < (data_cnt & AHC_SG_LEN_MASK)) { 4228 4229 sg--; 4230 sglen = ahc_le32toh(sg->len); 4231 /* 4232 * Preserve High Address and SG_LIST bits 4233 * while setting the count to 1. 4234 */ 4235 data_cnt = 1 | (sglen & (~AHC_SG_LEN_MASK)); 4236 data_addr = ahc_le32toh(sg->addr) 4237 + (sglen & AHC_SG_LEN_MASK) - 1; 4238 4239 /* 4240 * Increment sg so it points to the 4241 * "next" sg. 4242 */ 4243 sg++; 4244 sgptr = ahc_sg_virt_to_bus(scb, sg); 4245 } 4246 ahc_outl(ahc, SCB_RESIDUAL_SGPTR, sgptr); 4247 ahc_outl(ahc, SCB_RESIDUAL_DATACNT, data_cnt); 4248 /* 4249 * Toggle the "oddness" of the transfer length 4250 * to handle this mid-transfer ignore wide 4251 * residue. This ensures that the oddness is 4252 * correct for subsequent data transfers. 4253 */ 4254 ahc_outb(ahc, SCB_LUN, 4255 ahc_inb(ahc, SCB_LUN) ^ SCB_XFERLEN_ODD); 4256 } 4257 } 4258} 4259 4260 4261/* 4262 * Reinitialize the data pointers for the active transfer 4263 * based on its current residual. 4264 */ 4265static void 4266ahc_reinitialize_dataptrs(struct ahc_softc *ahc) 4267{ 4268 struct scb *scb; 4269 struct ahc_dma_seg *sg; 4270 u_int scb_index; 4271 uint32_t sgptr; 4272 uint32_t resid; 4273 uint32_t dataptr; 4274 4275 scb_index = ahc_inb(ahc, SCB_TAG); 4276 scb = ahc_lookup_scb(ahc, scb_index); 4277 sgptr = (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 3) << 24) 4278 | (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 2) << 16) 4279 | (ahc_inb(ahc, SCB_RESIDUAL_SGPTR + 1) << 8) 4280 | ahc_inb(ahc, SCB_RESIDUAL_SGPTR); 4281 4282 sgptr &= SG_PTR_MASK; 4283 sg = ahc_sg_bus_to_virt(scb, sgptr); 4284 4285 /* The residual sg_ptr always points to the next sg */ 4286 sg--; 4287 4288 resid = (ahc_inb(ahc, SCB_RESIDUAL_DATACNT + 2) << 16) 4289 | (ahc_inb(ahc, SCB_RESIDUAL_DATACNT + 1) << 8) 4290 | ahc_inb(ahc, SCB_RESIDUAL_DATACNT); 4291 4292 dataptr = ahc_le32toh(sg->addr) 4293 + (ahc_le32toh(sg->len) & AHC_SG_LEN_MASK) 4294 - resid; 4295 if ((ahc->flags & AHC_39BIT_ADDRESSING) != 0) { 4296 u_int dscommand1; 4297 4298 dscommand1 = ahc_inb(ahc, DSCOMMAND1); 4299 ahc_outb(ahc, DSCOMMAND1, dscommand1 | HADDLDSEL0); 4300 ahc_outb(ahc, HADDR, 4301 (ahc_le32toh(sg->len) >> 24) & SG_HIGH_ADDR_BITS); 4302 ahc_outb(ahc, DSCOMMAND1, dscommand1); 4303 } 4304 ahc_outb(ahc, HADDR + 3, dataptr >> 24); 4305 ahc_outb(ahc, HADDR + 2, dataptr >> 16); 4306 ahc_outb(ahc, HADDR + 1, dataptr >> 8); 4307 ahc_outb(ahc, HADDR, dataptr); 4308 ahc_outb(ahc, HCNT + 2, resid >> 16); 4309 ahc_outb(ahc, HCNT + 1, resid >> 8); 4310 ahc_outb(ahc, HCNT, resid); 4311 if ((ahc->features & AHC_ULTRA2) == 0) { 4312 ahc_outb(ahc, STCNT + 2, resid >> 16); 4313 ahc_outb(ahc, STCNT + 1, resid >> 8); 4314 ahc_outb(ahc, STCNT, resid); 4315 } 4316} 4317 4318/* 4319 * Handle the effects of issuing a bus device reset message. 4320 */ 4321static void 4322ahc_handle_devreset(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 4323 cam_status status, char *message, int verbose_level) 4324{ 4325#ifdef AHC_TARGET_MODE 4326 struct ahc_tmode_tstate* tstate; 4327 u_int lun; 4328#endif 4329 int found; 4330 4331 found = ahc_abort_scbs(ahc, devinfo->target, devinfo->channel, 4332 CAM_LUN_WILDCARD, SCB_LIST_NULL, devinfo->role, 4333 status); 4334 4335#ifdef AHC_TARGET_MODE 4336 /* 4337 * Send an immediate notify ccb to all target mord peripheral 4338 * drivers affected by this action. 4339 */ 4340 tstate = ahc->enabled_targets[devinfo->our_scsiid]; 4341 if (tstate != NULL) { 4342 for (lun = 0; lun < AHC_NUM_LUNS; lun++) { 4343 struct ahc_tmode_lstate* lstate; 4344 4345 lstate = tstate->enabled_luns[lun]; 4346 if (lstate == NULL) 4347 continue; 4348 4349 ahc_queue_lstate_event(ahc, lstate, devinfo->our_scsiid, 4350 MSG_BUS_DEV_RESET, /*arg*/0); 4351 ahc_send_lstate_events(ahc, lstate); 4352 } 4353 } 4354#endif 4355 4356 /* 4357 * Go back to async/narrow transfers and renegotiate. 4358 */ 4359 ahc_set_width(ahc, devinfo, MSG_EXT_WDTR_BUS_8_BIT, 4360 AHC_TRANS_CUR, /*paused*/TRUE); 4361 ahc_set_syncrate(ahc, devinfo, /*syncrate*/NULL, 4362 /*period*/0, /*offset*/0, /*ppr_options*/0, 4363 AHC_TRANS_CUR, /*paused*/TRUE); 4364 4365 if (status != CAM_SEL_TIMEOUT) 4366 ahc_send_async(ahc, devinfo->channel, devinfo->target, 4367 CAM_LUN_WILDCARD, AC_SENT_BDR); 4368 4369 if (message != NULL 4370 && (verbose_level <= bootverbose)) 4371 printk("%s: %s on %c:%d. %d SCBs aborted\n", ahc_name(ahc), 4372 message, devinfo->channel, devinfo->target, found); 4373} 4374 4375#ifdef AHC_TARGET_MODE 4376static void 4377ahc_setup_target_msgin(struct ahc_softc *ahc, struct ahc_devinfo *devinfo, 4378 struct scb *scb) 4379{ 4380 4381 /* 4382 * To facilitate adding multiple messages together, 4383 * each routine should increment the index and len 4384 * variables instead of setting them explicitly. 4385 */ 4386 ahc->msgout_index = 0; 4387 ahc->msgout_len = 0; 4388 4389 if (scb != NULL && (scb->flags & SCB_AUTO_NEGOTIATE) != 0) 4390 ahc_build_transfer_msg(ahc, devinfo); 4391 else 4392 panic("ahc_intr: AWAITING target message with no message"); 4393 4394 ahc->msgout_index = 0; 4395 ahc->msg_type = MSG_TYPE_TARGET_MSGIN; 4396} 4397#endif 4398/**************************** Initialization **********************************/ 4399/* 4400 * Allocate a controller structure for a new device 4401 * and perform initial initializion. 4402 */ 4403struct ahc_softc * 4404ahc_alloc(void *platform_arg, char *name) 4405{ 4406 struct ahc_softc *ahc; 4407 int i; 4408 4409#ifndef __FreeBSD__ 4410 ahc = kmalloc(sizeof(*ahc), GFP_ATOMIC); 4411 if (!ahc) { 4412 printk("aic7xxx: cannot malloc softc!\n"); 4413 kfree(name); 4414 return NULL; 4415 } 4416#else 4417 ahc = device_get_softc((device_t)platform_arg); 4418#endif 4419 memset(ahc, 0, sizeof(*ahc)); 4420 ahc->seep_config = kmalloc(sizeof(*ahc->seep_config), GFP_ATOMIC); 4421 if (ahc->seep_config == NULL) { 4422#ifndef __FreeBSD__ 4423 kfree(ahc); 4424#endif 4425 kfree(name); 4426 return (NULL); 4427 } 4428 LIST_INIT(&ahc->pending_scbs); 4429 /* We don't know our unit number until the OSM sets it */ 4430 ahc->name = name; 4431 ahc->unit = -1; 4432 ahc->description = NULL; 4433 ahc->channel = 'A'; 4434 ahc->channel_b = 'B'; 4435 ahc->chip = AHC_NONE; 4436 ahc->features = AHC_FENONE; 4437 ahc->bugs = AHC_BUGNONE; 4438 ahc->flags = AHC_FNONE; 4439 /* 4440 * Default to all error reporting enabled with the 4441 * sequencer operating at its fastest speed. 4442 * The bus attach code may modify this. 4443 */ 4444 ahc->seqctl = FASTMODE; 4445 4446 for (i = 0; i < AHC_NUM_TARGETS; i++) 4447 TAILQ_INIT(&ahc->untagged_queues[i]); 4448 if (ahc_platform_alloc(ahc, platform_arg) != 0) { 4449 ahc_free(ahc); 4450 ahc = NULL; 4451 } 4452 return (ahc); 4453} 4454 4455int 4456ahc_softc_init(struct ahc_softc *ahc) 4457{ 4458 4459 /* The IRQMS bit is only valid on VL and EISA chips */ 4460 if ((ahc->chip & AHC_PCI) == 0) 4461 ahc->unpause = ahc_inb(ahc, HCNTRL) & IRQMS; 4462 else 4463 ahc->unpause = 0; 4464 ahc->pause = ahc->unpause | PAUSE; 4465 /* XXX The shared scb data stuff should be deprecated */ 4466 if (ahc->scb_data == NULL) { 4467 ahc->scb_data = kzalloc(sizeof(*ahc->scb_data), GFP_ATOMIC); 4468 if (ahc->scb_data == NULL) 4469 return (ENOMEM); 4470 } 4471 4472 return (0); 4473} 4474 4475void 4476ahc_set_unit(struct ahc_softc *ahc, int unit) 4477{ 4478 ahc->unit = unit; 4479} 4480 4481void 4482ahc_set_name(struct ahc_softc *ahc, char *name) 4483{ 4484 if (ahc->name != NULL) 4485 kfree(ahc->name); 4486 ahc->name = name; 4487} 4488 4489void 4490ahc_free(struct ahc_softc *ahc) 4491{ 4492 int i; 4493 4494 switch (ahc->init_level) { 4495 default: 4496 case 5: 4497 ahc_shutdown(ahc); 4498 /* FALLTHROUGH */ 4499 case 4: 4500 ahc_dmamap_unload(ahc, ahc->shared_data_dmat, 4501 ahc->shared_data_dmamap); 4502 /* FALLTHROUGH */ 4503 case 3: 4504 ahc_dmamem_free(ahc, ahc->shared_data_dmat, ahc->qoutfifo, 4505 ahc->shared_data_dmamap); 4506 ahc_dmamap_destroy(ahc, ahc->shared_data_dmat, 4507 ahc->shared_data_dmamap); 4508 /* FALLTHROUGH */ 4509 case 2: 4510 ahc_dma_tag_destroy(ahc, ahc->shared_data_dmat); 4511 case 1: 4512#ifndef __linux__ 4513 ahc_dma_tag_destroy(ahc, ahc->buffer_dmat); 4514#endif 4515 break; 4516 case 0: 4517 break; 4518 } 4519 4520#ifndef __linux__ 4521 ahc_dma_tag_destroy(ahc, ahc->parent_dmat); 4522#endif 4523 ahc_platform_free(ahc); 4524 ahc_fini_scbdata(ahc); 4525 for (i = 0; i < AHC_NUM_TARGETS; i++) { 4526 struct ahc_tmode_tstate *tstate; 4527 4528 tstate = ahc->enabled_targets[i]; 4529 if (tstate != NULL) { 4530#ifdef AHC_TARGET_MODE 4531 int j; 4532 4533 for (j = 0; j < AHC_NUM_LUNS; j++) { 4534 struct ahc_tmode_lstate *lstate; 4535 4536 lstate = tstate->enabled_luns[j]; 4537 if (lstate != NULL) { 4538 xpt_free_path(lstate->path); 4539 kfree(lstate); 4540 } 4541 } 4542#endif 4543 kfree(tstate); 4544 } 4545 } 4546#ifdef AHC_TARGET_MODE 4547 if (ahc->black_hole != NULL) { 4548 xpt_free_path(ahc->black_hole->path); 4549 kfree(ahc->black_hole); 4550 } 4551#endif 4552 if (ahc->name != NULL) 4553 kfree(ahc->name); 4554 if (ahc->seep_config != NULL) 4555 kfree(ahc->seep_config); 4556#ifndef __FreeBSD__ 4557 kfree(ahc); 4558#endif 4559 return; 4560} 4561 4562static void 4563ahc_shutdown(void *arg) 4564{ 4565 struct ahc_softc *ahc; 4566 int i; 4567 4568 ahc = (struct ahc_softc *)arg; 4569 4570 /* This will reset most registers to 0, but not all */ 4571 ahc_reset(ahc, /*reinit*/FALSE); 4572 ahc_outb(ahc, SCSISEQ, 0); 4573 ahc_outb(ahc, SXFRCTL0, 0); 4574 ahc_outb(ahc, DSPCISTATUS, 0); 4575 4576 for (i = TARG_SCSIRATE; i < SCSICONF; i++) 4577 ahc_outb(ahc, i, 0); 4578} 4579 4580/* 4581 * Reset the controller and record some information about it 4582 * that is only available just after a reset. If "reinit" is 4583 * non-zero, this reset occurred after initial configuration 4584 * and the caller requests that the chip be fully reinitialized 4585 * to a runable state. Chip interrupts are *not* enabled after 4586 * a reinitialization. The caller must enable interrupts via 4587 * ahc_intr_enable(). 4588 */ 4589int 4590ahc_reset(struct ahc_softc *ahc, int reinit) 4591{ 4592 u_int sblkctl; 4593 u_int sxfrctl1_a, sxfrctl1_b; 4594 int error; 4595 int wait; 4596 4597 /* 4598 * Preserve the value of the SXFRCTL1 register for all channels. 4599 * It contains settings that affect termination and we don't want 4600 * to disturb the integrity of the bus. 4601 */ 4602 ahc_pause(ahc); 4603 sxfrctl1_b = 0; 4604 if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7770) { 4605 u_int sblkctl; 4606 4607 /* 4608 * Save channel B's settings in case this chip 4609 * is setup for TWIN channel operation. 4610 */ 4611 sblkctl = ahc_inb(ahc, SBLKCTL); 4612 ahc_outb(ahc, SBLKCTL, sblkctl | SELBUSB); 4613 sxfrctl1_b = ahc_inb(ahc, SXFRCTL1); 4614 ahc_outb(ahc, SBLKCTL, sblkctl & ~SELBUSB); 4615 } 4616 sxfrctl1_a = ahc_inb(ahc, SXFRCTL1); 4617 4618 ahc_outb(ahc, HCNTRL, CHIPRST | ahc->pause); 4619 4620 /* 4621 * Ensure that the reset has finished. We delay 1000us 4622 * prior to reading the register to make sure the chip 4623 * has sufficiently completed its reset to handle register 4624 * accesses. 4625 */ 4626 wait = 1000; 4627 do { 4628 ahc_delay(1000); 4629 } while (--wait && !(ahc_inb(ahc, HCNTRL) & CHIPRSTACK)); 4630 4631 if (wait == 0) { 4632 printk("%s: WARNING - Failed chip reset! " 4633 "Trying to initialize anyway.\n", ahc_name(ahc)); 4634 } 4635 ahc_outb(ahc, HCNTRL, ahc->pause); 4636 4637 /* Determine channel configuration */ 4638 sblkctl = ahc_inb(ahc, SBLKCTL) & (SELBUSB|SELWIDE); 4639 /* No Twin Channel PCI cards */ 4640 if ((ahc->chip & AHC_PCI) != 0) 4641 sblkctl &= ~SELBUSB; 4642 switch (sblkctl) { 4643 case 0: 4644 /* Single Narrow Channel */ 4645 break; 4646 case 2: 4647 /* Wide Channel */ 4648 ahc->features |= AHC_WIDE; 4649 break; 4650 case 8: 4651 /* Twin Channel */ 4652 ahc->features |= AHC_TWIN; 4653 break; 4654 default: 4655 printk(" Unsupported adapter type. Ignoring\n"); 4656 return(-1); 4657 } 4658 4659 /* 4660 * Reload sxfrctl1. 4661 * 4662 * We must always initialize STPWEN to 1 before we 4663 * restore the saved values. STPWEN is initialized 4664 * to a tri-state condition which can only be cleared 4665 * by turning it on. 4666 */ 4667 if ((ahc->features & AHC_TWIN) != 0) { 4668 u_int sblkctl; 4669 4670 sblkctl = ahc_inb(ahc, SBLKCTL); 4671 ahc_outb(ahc, SBLKCTL, sblkctl | SELBUSB); 4672 ahc_outb(ahc, SXFRCTL1, sxfrctl1_b); 4673 ahc_outb(ahc, SBLKCTL, sblkctl & ~SELBUSB); 4674 } 4675 ahc_outb(ahc, SXFRCTL1, sxfrctl1_a); 4676 4677 error = 0; 4678 if (reinit != 0) 4679 /* 4680 * If a recovery action has forced a chip reset, 4681 * re-initialize the chip to our liking. 4682 */ 4683 error = ahc->bus_chip_init(ahc); 4684#ifdef AHC_DUMP_SEQ 4685 else 4686 ahc_dumpseq(ahc); 4687#endif 4688 4689 return (error); 4690} 4691 4692/* 4693 * Determine the number of SCBs available on the controller 4694 */ 4695int 4696ahc_probe_scbs(struct ahc_softc *ahc) { 4697 int i; 4698 4699 for (i = 0; i < AHC_SCB_MAX; i++) { 4700 4701 ahc_outb(ahc, SCBPTR, i); 4702 ahc_outb(ahc, SCB_BASE, i); 4703 if (ahc_inb(ahc, SCB_BASE) != i) 4704 break; 4705 ahc_outb(ahc, SCBPTR, 0); 4706 if (ahc_inb(ahc, SCB_BASE) != 0) 4707 break; 4708 } 4709 return (i); 4710} 4711 4712static void 4713ahc_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) 4714{ 4715 dma_addr_t *baddr; 4716 4717 baddr = (dma_addr_t *)arg; 4718 *baddr = segs->ds_addr; 4719} 4720 4721static void 4722ahc_build_free_scb_list(struct ahc_softc *ahc) 4723{ 4724 int scbsize; 4725 int i; 4726 4727 scbsize = 32; 4728 if ((ahc->flags & AHC_LSCBS_ENABLED) != 0) 4729 scbsize = 64; 4730 4731 for (i = 0; i < ahc->scb_data->maxhscbs; i++) { 4732 int j; 4733 4734 ahc_outb(ahc, SCBPTR, i); 4735 4736 /* 4737 * Touch all SCB bytes to avoid parity errors 4738 * should one of our debugging routines read 4739 * an otherwise uninitiatlized byte. 4740 */ 4741 for (j = 0; j < scbsize; j++) 4742 ahc_outb(ahc, SCB_BASE+j, 0xFF); 4743 4744 /* Clear the control byte. */ 4745 ahc_outb(ahc, SCB_CONTROL, 0); 4746 4747 /* Set the next pointer */ 4748 if ((ahc->flags & AHC_PAGESCBS) != 0) 4749 ahc_outb(ahc, SCB_NEXT, i+1); 4750 else 4751 ahc_outb(ahc, SCB_NEXT, SCB_LIST_NULL); 4752 4753 /* Make the tag number, SCSIID, and lun invalid */ 4754 ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); 4755 ahc_outb(ahc, SCB_SCSIID, 0xFF); 4756 ahc_outb(ahc, SCB_LUN, 0xFF); 4757 } 4758 4759 if ((ahc->flags & AHC_PAGESCBS) != 0) { 4760 /* SCB 0 heads the free list. */ 4761 ahc_outb(ahc, FREE_SCBH, 0); 4762 } else { 4763 /* No free list. */ 4764 ahc_outb(ahc, FREE_SCBH, SCB_LIST_NULL); 4765 } 4766 4767 /* Make sure that the last SCB terminates the free list */ 4768 ahc_outb(ahc, SCBPTR, i-1); 4769 ahc_outb(ahc, SCB_NEXT, SCB_LIST_NULL); 4770} 4771 4772static int 4773ahc_init_scbdata(struct ahc_softc *ahc) 4774{ 4775 struct scb_data *scb_data; 4776 4777 scb_data = ahc->scb_data; 4778 SLIST_INIT(&scb_data->free_scbs); 4779 SLIST_INIT(&scb_data->sg_maps); 4780 4781 /* Allocate SCB resources */ 4782 scb_data->scbarray = kzalloc(sizeof(struct scb) * AHC_SCB_MAX_ALLOC, 4783 GFP_ATOMIC); 4784 if (scb_data->scbarray == NULL) 4785 return (ENOMEM); 4786 4787 /* Determine the number of hardware SCBs and initialize them */ 4788 4789 scb_data->maxhscbs = ahc_probe_scbs(ahc); 4790 if (ahc->scb_data->maxhscbs == 0) { 4791 printk("%s: No SCB space found\n", ahc_name(ahc)); 4792 return (ENXIO); 4793 } 4794 4795 /* 4796 * Create our DMA tags. These tags define the kinds of device 4797 * accessible memory allocations and memory mappings we will 4798 * need to perform during normal operation. 4799 * 4800 * Unless we need to further restrict the allocation, we rely 4801 * on the restrictions of the parent dmat, hence the common 4802 * use of MAXADDR and MAXSIZE. 4803 */ 4804 4805 /* DMA tag for our hardware scb structures */ 4806 if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, 4807 /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, 4808 /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, 4809 /*highaddr*/BUS_SPACE_MAXADDR, 4810 /*filter*/NULL, /*filterarg*/NULL, 4811 AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb), 4812 /*nsegments*/1, 4813 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 4814 /*flags*/0, &scb_data->hscb_dmat) != 0) { 4815 goto error_exit; 4816 } 4817 4818 scb_data->init_level++; 4819 4820 /* Allocation for our hscbs */ 4821 if (ahc_dmamem_alloc(ahc, scb_data->hscb_dmat, 4822 (void **)&scb_data->hscbs, 4823 BUS_DMA_NOWAIT, &scb_data->hscb_dmamap) != 0) { 4824 goto error_exit; 4825 } 4826 4827 scb_data->init_level++; 4828 4829 /* And permanently map them */ 4830 ahc_dmamap_load(ahc, scb_data->hscb_dmat, scb_data->hscb_dmamap, 4831 scb_data->hscbs, 4832 AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb), 4833 ahc_dmamap_cb, &scb_data->hscb_busaddr, /*flags*/0); 4834 4835 scb_data->init_level++; 4836 4837 /* DMA tag for our sense buffers */ 4838 if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, 4839 /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, 4840 /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, 4841 /*highaddr*/BUS_SPACE_MAXADDR, 4842 /*filter*/NULL, /*filterarg*/NULL, 4843 AHC_SCB_MAX_ALLOC * sizeof(struct scsi_sense_data), 4844 /*nsegments*/1, 4845 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 4846 /*flags*/0, &scb_data->sense_dmat) != 0) { 4847 goto error_exit; 4848 } 4849 4850 scb_data->init_level++; 4851 4852 /* Allocate them */ 4853 if (ahc_dmamem_alloc(ahc, scb_data->sense_dmat, 4854 (void **)&scb_data->sense, 4855 BUS_DMA_NOWAIT, &scb_data->sense_dmamap) != 0) { 4856 goto error_exit; 4857 } 4858 4859 scb_data->init_level++; 4860 4861 /* And permanently map them */ 4862 ahc_dmamap_load(ahc, scb_data->sense_dmat, scb_data->sense_dmamap, 4863 scb_data->sense, 4864 AHC_SCB_MAX_ALLOC * sizeof(struct scsi_sense_data), 4865 ahc_dmamap_cb, &scb_data->sense_busaddr, /*flags*/0); 4866 4867 scb_data->init_level++; 4868 4869 /* DMA tag for our S/G structures. We allocate in page sized chunks */ 4870 if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/8, 4871 /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, 4872 /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, 4873 /*highaddr*/BUS_SPACE_MAXADDR, 4874 /*filter*/NULL, /*filterarg*/NULL, 4875 PAGE_SIZE, /*nsegments*/1, 4876 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 4877 /*flags*/0, &scb_data->sg_dmat) != 0) { 4878 goto error_exit; 4879 } 4880 4881 scb_data->init_level++; 4882 4883 /* Perform initial CCB allocation */ 4884 memset(scb_data->hscbs, 0, 4885 AHC_SCB_MAX_ALLOC * sizeof(struct hardware_scb)); 4886 ahc_alloc_scbs(ahc); 4887 4888 if (scb_data->numscbs == 0) { 4889 printk("%s: ahc_init_scbdata - " 4890 "Unable to allocate initial scbs\n", 4891 ahc_name(ahc)); 4892 goto error_exit; 4893 } 4894 4895 /* 4896 * Reserve the next queued SCB. 4897 */ 4898 ahc->next_queued_scb = ahc_get_scb(ahc); 4899 4900 /* 4901 * Note that we were successful 4902 */ 4903 return (0); 4904 4905error_exit: 4906 4907 return (ENOMEM); 4908} 4909 4910static void 4911ahc_fini_scbdata(struct ahc_softc *ahc) 4912{ 4913 struct scb_data *scb_data; 4914 4915 scb_data = ahc->scb_data; 4916 if (scb_data == NULL) 4917 return; 4918 4919 switch (scb_data->init_level) { 4920 default: 4921 case 7: 4922 { 4923 struct sg_map_node *sg_map; 4924 4925 while ((sg_map = SLIST_FIRST(&scb_data->sg_maps))!= NULL) { 4926 SLIST_REMOVE_HEAD(&scb_data->sg_maps, links); 4927 ahc_dmamap_unload(ahc, scb_data->sg_dmat, 4928 sg_map->sg_dmamap); 4929 ahc_dmamem_free(ahc, scb_data->sg_dmat, 4930 sg_map->sg_vaddr, 4931 sg_map->sg_dmamap); 4932 kfree(sg_map); 4933 } 4934 ahc_dma_tag_destroy(ahc, scb_data->sg_dmat); 4935 } 4936 case 6: 4937 ahc_dmamap_unload(ahc, scb_data->sense_dmat, 4938 scb_data->sense_dmamap); 4939 case 5: 4940 ahc_dmamem_free(ahc, scb_data->sense_dmat, scb_data->sense, 4941 scb_data->sense_dmamap); 4942 ahc_dmamap_destroy(ahc, scb_data->sense_dmat, 4943 scb_data->sense_dmamap); 4944 case 4: 4945 ahc_dma_tag_destroy(ahc, scb_data->sense_dmat); 4946 case 3: 4947 ahc_dmamap_unload(ahc, scb_data->hscb_dmat, 4948 scb_data->hscb_dmamap); 4949 case 2: 4950 ahc_dmamem_free(ahc, scb_data->hscb_dmat, scb_data->hscbs, 4951 scb_data->hscb_dmamap); 4952 ahc_dmamap_destroy(ahc, scb_data->hscb_dmat, 4953 scb_data->hscb_dmamap); 4954 case 1: 4955 ahc_dma_tag_destroy(ahc, scb_data->hscb_dmat); 4956 break; 4957 case 0: 4958 break; 4959 } 4960 if (scb_data->scbarray != NULL) 4961 kfree(scb_data->scbarray); 4962} 4963 4964static void 4965ahc_alloc_scbs(struct ahc_softc *ahc) 4966{ 4967 struct scb_data *scb_data; 4968 struct scb *next_scb; 4969 struct sg_map_node *sg_map; 4970 dma_addr_t physaddr; 4971 struct ahc_dma_seg *segs; 4972 int newcount; 4973 int i; 4974 4975 scb_data = ahc->scb_data; 4976 if (scb_data->numscbs >= AHC_SCB_MAX_ALLOC) 4977 /* Can't allocate any more */ 4978 return; 4979 4980 next_scb = &scb_data->scbarray[scb_data->numscbs]; 4981 4982 sg_map = kmalloc(sizeof(*sg_map), GFP_ATOMIC); 4983 4984 if (sg_map == NULL) 4985 return; 4986 4987 /* Allocate S/G space for the next batch of SCBS */ 4988 if (ahc_dmamem_alloc(ahc, scb_data->sg_dmat, 4989 (void **)&sg_map->sg_vaddr, 4990 BUS_DMA_NOWAIT, &sg_map->sg_dmamap) != 0) { 4991 kfree(sg_map); 4992 return; 4993 } 4994 4995 SLIST_INSERT_HEAD(&scb_data->sg_maps, sg_map, links); 4996 4997 ahc_dmamap_load(ahc, scb_data->sg_dmat, sg_map->sg_dmamap, 4998 sg_map->sg_vaddr, PAGE_SIZE, ahc_dmamap_cb, 4999 &sg_map->sg_physaddr, /*flags*/0); 5000 5001 segs = sg_map->sg_vaddr; 5002 physaddr = sg_map->sg_physaddr; 5003 5004 newcount = (PAGE_SIZE / (AHC_NSEG * sizeof(struct ahc_dma_seg))); 5005 newcount = min(newcount, (AHC_SCB_MAX_ALLOC - scb_data->numscbs)); 5006 for (i = 0; i < newcount; i++) { 5007 struct scb_platform_data *pdata; 5008#ifndef __linux__ 5009 int error; 5010#endif 5011 pdata = kmalloc(sizeof(*pdata), GFP_ATOMIC); 5012 if (pdata == NULL) 5013 break; 5014 next_scb->platform_data = pdata; 5015 next_scb->sg_map = sg_map; 5016 next_scb->sg_list = segs; 5017 /* 5018 * The sequencer always starts with the second entry. 5019 * The first entry is embedded in the scb. 5020 */ 5021 next_scb->sg_list_phys = physaddr + sizeof(struct ahc_dma_seg); 5022 next_scb->ahc_softc = ahc; 5023 next_scb->flags = SCB_FREE; 5024#ifndef __linux__ 5025 error = ahc_dmamap_create(ahc, ahc->buffer_dmat, /*flags*/0, 5026 &next_scb->dmamap); 5027 if (error != 0) 5028 break; 5029#endif 5030 next_scb->hscb = &scb_data->hscbs[scb_data->numscbs]; 5031 next_scb->hscb->tag = ahc->scb_data->numscbs; 5032 SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, 5033 next_scb, links.sle); 5034 segs += AHC_NSEG; 5035 physaddr += (AHC_NSEG * sizeof(struct ahc_dma_seg)); 5036 next_scb++; 5037 ahc->scb_data->numscbs++; 5038 } 5039} 5040 5041void 5042ahc_controller_info(struct ahc_softc *ahc, char *buf) 5043{ 5044 int len; 5045 5046 len = sprintf(buf, "%s: ", ahc_chip_names[ahc->chip & AHC_CHIPID_MASK]); 5047 buf += len; 5048 if ((ahc->features & AHC_TWIN) != 0) 5049 len = sprintf(buf, "Twin Channel, A SCSI Id=%d, " 5050 "B SCSI Id=%d, primary %c, ", 5051 ahc->our_id, ahc->our_id_b, 5052 (ahc->flags & AHC_PRIMARY_CHANNEL) + 'A'); 5053 else { 5054 const char *speed; 5055 const char *type; 5056 5057 speed = ""; 5058 if ((ahc->features & AHC_ULTRA) != 0) { 5059 speed = "Ultra "; 5060 } else if ((ahc->features & AHC_DT) != 0) { 5061 speed = "Ultra160 "; 5062 } else if ((ahc->features & AHC_ULTRA2) != 0) { 5063 speed = "Ultra2 "; 5064 } 5065 if ((ahc->features & AHC_WIDE) != 0) { 5066 type = "Wide"; 5067 } else { 5068 type = "Single"; 5069 } 5070 len = sprintf(buf, "%s%s Channel %c, SCSI Id=%d, ", 5071 speed, type, ahc->channel, ahc->our_id); 5072 } 5073 buf += len; 5074 5075 if ((ahc->flags & AHC_PAGESCBS) != 0) 5076 sprintf(buf, "%d/%d SCBs", 5077 ahc->scb_data->maxhscbs, AHC_MAX_QUEUE); 5078 else 5079 sprintf(buf, "%d SCBs", ahc->scb_data->maxhscbs); 5080} 5081 5082int 5083ahc_chip_init(struct ahc_softc *ahc) 5084{ 5085 int term; 5086 int error; 5087 u_int i; 5088 u_int scsi_conf; 5089 u_int scsiseq_template; 5090 uint32_t physaddr; 5091 5092 ahc_outb(ahc, SEQ_FLAGS, 0); 5093 ahc_outb(ahc, SEQ_FLAGS2, 0); 5094 5095 /* Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1, for both channels*/ 5096 if (ahc->features & AHC_TWIN) { 5097 5098 /* 5099 * Setup Channel B first. 5100 */ 5101 ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) | SELBUSB); 5102 term = (ahc->flags & AHC_TERM_ENB_B) != 0 ? STPWEN : 0; 5103 ahc_outb(ahc, SCSIID, ahc->our_id_b); 5104 scsi_conf = ahc_inb(ahc, SCSICONF + 1); 5105 ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) 5106 |term|ahc->seltime_b|ENSTIMER|ACTNEGEN); 5107 if ((ahc->features & AHC_ULTRA2) != 0) 5108 ahc_outb(ahc, SIMODE0, ahc_inb(ahc, SIMODE0)|ENIOERR); 5109 ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); 5110 ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); 5111 5112 /* Select Channel A */ 5113 ahc_outb(ahc, SBLKCTL, ahc_inb(ahc, SBLKCTL) & ~SELBUSB); 5114 } 5115 term = (ahc->flags & AHC_TERM_ENB_A) != 0 ? STPWEN : 0; 5116 if ((ahc->features & AHC_ULTRA2) != 0) 5117 ahc_outb(ahc, SCSIID_ULTRA2, ahc->our_id); 5118 else 5119 ahc_outb(ahc, SCSIID, ahc->our_id); 5120 scsi_conf = ahc_inb(ahc, SCSICONF); 5121 ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) 5122 |term|ahc->seltime 5123 |ENSTIMER|ACTNEGEN); 5124 if ((ahc->features & AHC_ULTRA2) != 0) 5125 ahc_outb(ahc, SIMODE0, ahc_inb(ahc, SIMODE0)|ENIOERR); 5126 ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); 5127 ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); 5128 5129 /* There are no untagged SCBs active yet. */ 5130 for (i = 0; i < 16; i++) { 5131 ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, 0)); 5132 if ((ahc->flags & AHC_SCB_BTT) != 0) { 5133 int lun; 5134 5135 /* 5136 * The SCB based BTT allows an entry per 5137 * target and lun pair. 5138 */ 5139 for (lun = 1; lun < AHC_NUM_LUNS; lun++) 5140 ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, lun)); 5141 } 5142 } 5143 5144 /* All of our queues are empty */ 5145 for (i = 0; i < 256; i++) 5146 ahc->qoutfifo[i] = SCB_LIST_NULL; 5147 ahc_sync_qoutfifo(ahc, BUS_DMASYNC_PREREAD); 5148 5149 for (i = 0; i < 256; i++) 5150 ahc->qinfifo[i] = SCB_LIST_NULL; 5151 5152 if ((ahc->features & AHC_MULTI_TID) != 0) { 5153 ahc_outb(ahc, TARGID, 0); 5154 ahc_outb(ahc, TARGID + 1, 0); 5155 } 5156 5157 /* 5158 * Tell the sequencer where it can find our arrays in memory. 5159 */ 5160 physaddr = ahc->scb_data->hscb_busaddr; 5161 ahc_outb(ahc, HSCB_ADDR, physaddr & 0xFF); 5162 ahc_outb(ahc, HSCB_ADDR + 1, (physaddr >> 8) & 0xFF); 5163 ahc_outb(ahc, HSCB_ADDR + 2, (physaddr >> 16) & 0xFF); 5164 ahc_outb(ahc, HSCB_ADDR + 3, (physaddr >> 24) & 0xFF); 5165 5166 physaddr = ahc->shared_data_busaddr; 5167 ahc_outb(ahc, SHARED_DATA_ADDR, physaddr & 0xFF); 5168 ahc_outb(ahc, SHARED_DATA_ADDR + 1, (physaddr >> 8) & 0xFF); 5169 ahc_outb(ahc, SHARED_DATA_ADDR + 2, (physaddr >> 16) & 0xFF); 5170 ahc_outb(ahc, SHARED_DATA_ADDR + 3, (physaddr >> 24) & 0xFF); 5171 5172 /* 5173 * Initialize the group code to command length table. 5174 * This overrides the values in TARG_SCSIRATE, so only 5175 * setup the table after we have processed that information. 5176 */ 5177 ahc_outb(ahc, CMDSIZE_TABLE, 5); 5178 ahc_outb(ahc, CMDSIZE_TABLE + 1, 9); 5179 ahc_outb(ahc, CMDSIZE_TABLE + 2, 9); 5180 ahc_outb(ahc, CMDSIZE_TABLE + 3, 0); 5181 ahc_outb(ahc, CMDSIZE_TABLE + 4, 15); 5182 ahc_outb(ahc, CMDSIZE_TABLE + 5, 11); 5183 ahc_outb(ahc, CMDSIZE_TABLE + 6, 0); 5184 ahc_outb(ahc, CMDSIZE_TABLE + 7, 0); 5185 5186 if ((ahc->features & AHC_HS_MAILBOX) != 0) 5187 ahc_outb(ahc, HS_MAILBOX, 0); 5188 5189 /* Tell the sequencer of our initial queue positions */ 5190 if ((ahc->features & AHC_TARGETMODE) != 0) { 5191 ahc->tqinfifonext = 1; 5192 ahc_outb(ahc, KERNEL_TQINPOS, ahc->tqinfifonext - 1); 5193 ahc_outb(ahc, TQINPOS, ahc->tqinfifonext); 5194 } 5195 ahc->qinfifonext = 0; 5196 ahc->qoutfifonext = 0; 5197 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 5198 ahc_outb(ahc, QOFF_CTLSTA, SCB_QSIZE_256); 5199 ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); 5200 ahc_outb(ahc, SNSCB_QOFF, ahc->qinfifonext); 5201 ahc_outb(ahc, SDSCB_QOFF, 0); 5202 } else { 5203 ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); 5204 ahc_outb(ahc, QINPOS, ahc->qinfifonext); 5205 ahc_outb(ahc, QOUTPOS, ahc->qoutfifonext); 5206 } 5207 5208 /* We don't have any waiting selections */ 5209 ahc_outb(ahc, WAITING_SCBH, SCB_LIST_NULL); 5210 5211 /* Our disconnection list is empty too */ 5212 ahc_outb(ahc, DISCONNECTED_SCBH, SCB_LIST_NULL); 5213 5214 /* Message out buffer starts empty */ 5215 ahc_outb(ahc, MSG_OUT, MSG_NOOP); 5216 5217 /* 5218 * Setup the allowed SCSI Sequences based on operational mode. 5219 * If we are a target, we'll enable select in operations once 5220 * we've had a lun enabled. 5221 */ 5222 scsiseq_template = ENSELO|ENAUTOATNO|ENAUTOATNP; 5223 if ((ahc->flags & AHC_INITIATORROLE) != 0) 5224 scsiseq_template |= ENRSELI; 5225 ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq_template); 5226 5227 /* Initialize our list of free SCBs. */ 5228 ahc_build_free_scb_list(ahc); 5229 5230 /* 5231 * Tell the sequencer which SCB will be the next one it receives. 5232 */ 5233 ahc_outb(ahc, NEXT_QUEUED_SCB, ahc->next_queued_scb->hscb->tag); 5234 5235 /* 5236 * Load the Sequencer program and Enable the adapter 5237 * in "fast" mode. 5238 */ 5239 if (bootverbose) 5240 printk("%s: Downloading Sequencer Program...", 5241 ahc_name(ahc)); 5242 5243 error = ahc_loadseq(ahc); 5244 if (error != 0) 5245 return (error); 5246 5247 if ((ahc->features & AHC_ULTRA2) != 0) { 5248 int wait; 5249 5250 /* 5251 * Wait for up to 500ms for our transceivers 5252 * to settle. If the adapter does not have 5253 * a cable attached, the transceivers may 5254 * never settle, so don't complain if we 5255 * fail here. 5256 */ 5257 for (wait = 5000; 5258 (ahc_inb(ahc, SBLKCTL) & (ENAB40|ENAB20)) == 0 && wait; 5259 wait--) 5260 ahc_delay(100); 5261 } 5262 ahc_restart(ahc); 5263 return (0); 5264} 5265 5266/* 5267 * Start the board, ready for normal operation 5268 */ 5269int 5270ahc_init(struct ahc_softc *ahc) 5271{ 5272 int max_targ; 5273 u_int i; 5274 u_int scsi_conf; 5275 u_int ultraenb; 5276 u_int discenable; 5277 u_int tagenable; 5278 size_t driver_data_size; 5279 5280#ifdef AHC_DEBUG 5281 if ((ahc_debug & AHC_DEBUG_SEQUENCER) != 0) 5282 ahc->flags |= AHC_SEQUENCER_DEBUG; 5283#endif 5284 5285#ifdef AHC_PRINT_SRAM 5286 printk("Scratch Ram:"); 5287 for (i = 0x20; i < 0x5f; i++) { 5288 if (((i % 8) == 0) && (i != 0)) { 5289 printk ("\n "); 5290 } 5291 printk (" 0x%x", ahc_inb(ahc, i)); 5292 } 5293 if ((ahc->features & AHC_MORE_SRAM) != 0) { 5294 for (i = 0x70; i < 0x7f; i++) { 5295 if (((i % 8) == 0) && (i != 0)) { 5296 printk ("\n "); 5297 } 5298 printk (" 0x%x", ahc_inb(ahc, i)); 5299 } 5300 } 5301 printk ("\n"); 5302 /* 5303 * Reading uninitialized scratch ram may 5304 * generate parity errors. 5305 */ 5306 ahc_outb(ahc, CLRINT, CLRPARERR); 5307 ahc_outb(ahc, CLRINT, CLRBRKADRINT); 5308#endif 5309 max_targ = 15; 5310 5311 /* 5312 * Assume we have a board at this stage and it has been reset. 5313 */ 5314 if ((ahc->flags & AHC_USEDEFAULTS) != 0) 5315 ahc->our_id = ahc->our_id_b = 7; 5316 5317 /* 5318 * Default to allowing initiator operations. 5319 */ 5320 ahc->flags |= AHC_INITIATORROLE; 5321 5322 /* 5323 * Only allow target mode features if this unit has them enabled. 5324 */ 5325 if ((AHC_TMODE_ENABLE & (0x1 << ahc->unit)) == 0) 5326 ahc->features &= ~AHC_TARGETMODE; 5327 5328#ifndef __linux__ 5329 /* DMA tag for mapping buffers into device visible space. */ 5330 if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, 5331 /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, 5332 /*lowaddr*/ahc->flags & AHC_39BIT_ADDRESSING 5333 ? (dma_addr_t)0x7FFFFFFFFFULL 5334 : BUS_SPACE_MAXADDR_32BIT, 5335 /*highaddr*/BUS_SPACE_MAXADDR, 5336 /*filter*/NULL, /*filterarg*/NULL, 5337 /*maxsize*/(AHC_NSEG - 1) * PAGE_SIZE, 5338 /*nsegments*/AHC_NSEG, 5339 /*maxsegsz*/AHC_MAXTRANSFER_SIZE, 5340 /*flags*/BUS_DMA_ALLOCNOW, 5341 &ahc->buffer_dmat) != 0) { 5342 return (ENOMEM); 5343 } 5344#endif 5345 5346 ahc->init_level++; 5347 5348 /* 5349 * DMA tag for our command fifos and other data in system memory 5350 * the card's sequencer must be able to access. For initiator 5351 * roles, we need to allocate space for the qinfifo and qoutfifo. 5352 * The qinfifo and qoutfifo are composed of 256 1 byte elements. 5353 * When providing for the target mode role, we must additionally 5354 * provide space for the incoming target command fifo and an extra 5355 * byte to deal with a dma bug in some chip versions. 5356 */ 5357 driver_data_size = 2 * 256 * sizeof(uint8_t); 5358 if ((ahc->features & AHC_TARGETMODE) != 0) 5359 driver_data_size += AHC_TMODE_CMDS * sizeof(struct target_cmd) 5360 + /*DMA WideOdd Bug Buffer*/1; 5361 if (ahc_dma_tag_create(ahc, ahc->parent_dmat, /*alignment*/1, 5362 /*boundary*/BUS_SPACE_MAXADDR_32BIT + 1, 5363 /*lowaddr*/BUS_SPACE_MAXADDR_32BIT, 5364 /*highaddr*/BUS_SPACE_MAXADDR, 5365 /*filter*/NULL, /*filterarg*/NULL, 5366 driver_data_size, 5367 /*nsegments*/1, 5368 /*maxsegsz*/BUS_SPACE_MAXSIZE_32BIT, 5369 /*flags*/0, &ahc->shared_data_dmat) != 0) { 5370 return (ENOMEM); 5371 } 5372 5373 ahc->init_level++; 5374 5375 /* Allocation of driver data */ 5376 if (ahc_dmamem_alloc(ahc, ahc->shared_data_dmat, 5377 (void **)&ahc->qoutfifo, 5378 BUS_DMA_NOWAIT, &ahc->shared_data_dmamap) != 0) { 5379 return (ENOMEM); 5380 } 5381 5382 ahc->init_level++; 5383 5384 /* And permanently map it in */ 5385 ahc_dmamap_load(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap, 5386 ahc->qoutfifo, driver_data_size, ahc_dmamap_cb, 5387 &ahc->shared_data_busaddr, /*flags*/0); 5388 5389 if ((ahc->features & AHC_TARGETMODE) != 0) { 5390 ahc->targetcmds = (struct target_cmd *)ahc->qoutfifo; 5391 ahc->qoutfifo = (uint8_t *)&ahc->targetcmds[AHC_TMODE_CMDS]; 5392 ahc->dma_bug_buf = ahc->shared_data_busaddr 5393 + driver_data_size - 1; 5394 /* All target command blocks start out invalid. */ 5395 for (i = 0; i < AHC_TMODE_CMDS; i++) 5396 ahc->targetcmds[i].cmd_valid = 0; 5397 ahc_sync_tqinfifo(ahc, BUS_DMASYNC_PREREAD); 5398 ahc->qoutfifo = (uint8_t *)&ahc->targetcmds[256]; 5399 } 5400 ahc->qinfifo = &ahc->qoutfifo[256]; 5401 5402 ahc->init_level++; 5403 5404 /* Allocate SCB data now that buffer_dmat is initialized */ 5405 if (ahc->scb_data->maxhscbs == 0) 5406 if (ahc_init_scbdata(ahc) != 0) 5407 return (ENOMEM); 5408 5409 /* 5410 * Allocate a tstate to house information for our 5411 * initiator presence on the bus as well as the user 5412 * data for any target mode initiator. 5413 */ 5414 if (ahc_alloc_tstate(ahc, ahc->our_id, 'A') == NULL) { 5415 printk("%s: unable to allocate ahc_tmode_tstate. " 5416 "Failing attach\n", ahc_name(ahc)); 5417 return (ENOMEM); 5418 } 5419 5420 if ((ahc->features & AHC_TWIN) != 0) { 5421 if (ahc_alloc_tstate(ahc, ahc->our_id_b, 'B') == NULL) { 5422 printk("%s: unable to allocate ahc_tmode_tstate. " 5423 "Failing attach\n", ahc_name(ahc)); 5424 return (ENOMEM); 5425 } 5426 } 5427 5428 if (ahc->scb_data->maxhscbs < AHC_SCB_MAX_ALLOC) { 5429 ahc->flags |= AHC_PAGESCBS; 5430 } else { 5431 ahc->flags &= ~AHC_PAGESCBS; 5432 } 5433 5434#ifdef AHC_DEBUG 5435 if (ahc_debug & AHC_SHOW_MISC) { 5436 printk("%s: hardware scb %u bytes; kernel scb %u bytes; " 5437 "ahc_dma %u bytes\n", 5438 ahc_name(ahc), 5439 (u_int)sizeof(struct hardware_scb), 5440 (u_int)sizeof(struct scb), 5441 (u_int)sizeof(struct ahc_dma_seg)); 5442 } 5443#endif /* AHC_DEBUG */ 5444 5445 /* 5446 * Look at the information that board initialization or 5447 * the board bios has left us. 5448 */ 5449 if (ahc->features & AHC_TWIN) { 5450 scsi_conf = ahc_inb(ahc, SCSICONF + 1); 5451 if ((scsi_conf & RESET_SCSI) != 0 5452 && (ahc->flags & AHC_INITIATORROLE) != 0) 5453 ahc->flags |= AHC_RESET_BUS_B; 5454 } 5455 5456 scsi_conf = ahc_inb(ahc, SCSICONF); 5457 if ((scsi_conf & RESET_SCSI) != 0 5458 && (ahc->flags & AHC_INITIATORROLE) != 0) 5459 ahc->flags |= AHC_RESET_BUS_A; 5460 5461 ultraenb = 0; 5462 tagenable = ALL_TARGETS_MASK; 5463 5464 /* Grab the disconnection disable table and invert it for our needs */ 5465 if ((ahc->flags & AHC_USEDEFAULTS) != 0) { 5466 printk("%s: Host Adapter Bios disabled. Using default SCSI " 5467 "device parameters\n", ahc_name(ahc)); 5468 ahc->flags |= AHC_EXTENDED_TRANS_A|AHC_EXTENDED_TRANS_B| 5469 AHC_TERM_ENB_A|AHC_TERM_ENB_B; 5470 discenable = ALL_TARGETS_MASK; 5471 if ((ahc->features & AHC_ULTRA) != 0) 5472 ultraenb = ALL_TARGETS_MASK; 5473 } else { 5474 discenable = ~((ahc_inb(ahc, DISC_DSB + 1) << 8) 5475 | ahc_inb(ahc, DISC_DSB)); 5476 if ((ahc->features & (AHC_ULTRA|AHC_ULTRA2)) != 0) 5477 ultraenb = (ahc_inb(ahc, ULTRA_ENB + 1) << 8) 5478 | ahc_inb(ahc, ULTRA_ENB); 5479 } 5480 5481 if ((ahc->features & (AHC_WIDE|AHC_TWIN)) == 0) 5482 max_targ = 7; 5483 5484 for (i = 0; i <= max_targ; i++) { 5485 struct ahc_initiator_tinfo *tinfo; 5486 struct ahc_tmode_tstate *tstate; 5487 u_int our_id; 5488 u_int target_id; 5489 char channel; 5490 5491 channel = 'A'; 5492 our_id = ahc->our_id; 5493 target_id = i; 5494 if (i > 7 && (ahc->features & AHC_TWIN) != 0) { 5495 channel = 'B'; 5496 our_id = ahc->our_id_b; 5497 target_id = i % 8; 5498 } 5499 tinfo = ahc_fetch_transinfo(ahc, channel, our_id, 5500 target_id, &tstate); 5501 /* Default to async narrow across the board */ 5502 memset(tinfo, 0, sizeof(*tinfo)); 5503 if (ahc->flags & AHC_USEDEFAULTS) { 5504 if ((ahc->features & AHC_WIDE) != 0) 5505 tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT; 5506 5507 /* 5508 * These will be truncated when we determine the 5509 * connection type we have with the target. 5510 */ 5511 tinfo->user.period = ahc_syncrates->period; 5512 tinfo->user.offset = MAX_OFFSET; 5513 } else { 5514 u_int scsirate; 5515 uint16_t mask; 5516 5517 /* Take the settings leftover in scratch RAM. */ 5518 scsirate = ahc_inb(ahc, TARG_SCSIRATE + i); 5519 mask = (0x01 << i); 5520 if ((ahc->features & AHC_ULTRA2) != 0) { 5521 u_int offset; 5522 u_int maxsync; 5523 5524 if ((scsirate & SOFS) == 0x0F) { 5525 /* 5526 * Haven't negotiated yet, 5527 * so the format is different. 5528 */ 5529 scsirate = (scsirate & SXFR) >> 4 5530 | (ultraenb & mask) 5531 ? 0x08 : 0x0 5532 | (scsirate & WIDEXFER); 5533 offset = MAX_OFFSET_ULTRA2; 5534 } else 5535 offset = ahc_inb(ahc, TARG_OFFSET + i); 5536 if ((scsirate & ~WIDEXFER) == 0 && offset != 0) 5537 /* Set to the lowest sync rate, 5MHz */ 5538 scsirate |= 0x1c; 5539 maxsync = AHC_SYNCRATE_ULTRA2; 5540 if ((ahc->features & AHC_DT) != 0) 5541 maxsync = AHC_SYNCRATE_DT; 5542 tinfo->user.period = 5543 ahc_find_period(ahc, scsirate, maxsync); 5544 if (offset == 0) 5545 tinfo->user.period = 0; 5546 else 5547 tinfo->user.offset = MAX_OFFSET; 5548 if ((scsirate & SXFR_ULTRA2) <= 8/*10MHz*/ 5549 && (ahc->features & AHC_DT) != 0) 5550 tinfo->user.ppr_options = 5551 MSG_EXT_PPR_DT_REQ; 5552 } else if ((scsirate & SOFS) != 0) { 5553 if ((scsirate & SXFR) == 0x40 5554 && (ultraenb & mask) != 0) { 5555 /* Treat 10MHz as a non-ultra speed */ 5556 scsirate &= ~SXFR; 5557 ultraenb &= ~mask; 5558 } 5559 tinfo->user.period = 5560 ahc_find_period(ahc, scsirate, 5561 (ultraenb & mask) 5562 ? AHC_SYNCRATE_ULTRA 5563 : AHC_SYNCRATE_FAST); 5564 if (tinfo->user.period != 0) 5565 tinfo->user.offset = MAX_OFFSET; 5566 } 5567 if (tinfo->user.period == 0) 5568 tinfo->user.offset = 0; 5569 if ((scsirate & WIDEXFER) != 0 5570 && (ahc->features & AHC_WIDE) != 0) 5571 tinfo->user.width = MSG_EXT_WDTR_BUS_16_BIT; 5572 tinfo->user.protocol_version = 4; 5573 if ((ahc->features & AHC_DT) != 0) 5574 tinfo->user.transport_version = 3; 5575 else 5576 tinfo->user.transport_version = 2; 5577 tinfo->goal.protocol_version = 2; 5578 tinfo->goal.transport_version = 2; 5579 tinfo->curr.protocol_version = 2; 5580 tinfo->curr.transport_version = 2; 5581 } 5582 tstate->ultraenb = 0; 5583 } 5584 ahc->user_discenable = discenable; 5585 ahc->user_tagenable = tagenable; 5586 5587 return (ahc->bus_chip_init(ahc)); 5588} 5589 5590void 5591ahc_intr_enable(struct ahc_softc *ahc, int enable) 5592{ 5593 u_int hcntrl; 5594 5595 hcntrl = ahc_inb(ahc, HCNTRL); 5596 hcntrl &= ~INTEN; 5597 ahc->pause &= ~INTEN; 5598 ahc->unpause &= ~INTEN; 5599 if (enable) { 5600 hcntrl |= INTEN; 5601 ahc->pause |= INTEN; 5602 ahc->unpause |= INTEN; 5603 } 5604 ahc_outb(ahc, HCNTRL, hcntrl); 5605} 5606 5607/* 5608 * Ensure that the card is paused in a location 5609 * outside of all critical sections and that all 5610 * pending work is completed prior to returning. 5611 * This routine should only be called from outside 5612 * an interrupt context. 5613 */ 5614void 5615ahc_pause_and_flushwork(struct ahc_softc *ahc) 5616{ 5617 int intstat; 5618 int maxloops; 5619 int paused; 5620 5621 maxloops = 1000; 5622 ahc->flags |= AHC_ALL_INTERRUPTS; 5623 paused = FALSE; 5624 do { 5625 if (paused) { 5626 ahc_unpause(ahc); 5627 /* 5628 * Give the sequencer some time to service 5629 * any active selections. 5630 */ 5631 ahc_delay(500); 5632 } 5633 ahc_intr(ahc); 5634 ahc_pause(ahc); 5635 paused = TRUE; 5636 ahc_outb(ahc, SCSISEQ, ahc_inb(ahc, SCSISEQ) & ~ENSELO); 5637 intstat = ahc_inb(ahc, INTSTAT); 5638 if ((intstat & INT_PEND) == 0) { 5639 ahc_clear_critical_section(ahc); 5640 intstat = ahc_inb(ahc, INTSTAT); 5641 } 5642 } while (--maxloops 5643 && (intstat != 0xFF || (ahc->features & AHC_REMOVABLE) == 0) 5644 && ((intstat & INT_PEND) != 0 5645 || (ahc_inb(ahc, SSTAT0) & (SELDO|SELINGO)) != 0)); 5646 if (maxloops == 0) { 5647 printk("Infinite interrupt loop, INTSTAT = %x", 5648 ahc_inb(ahc, INTSTAT)); 5649 } 5650 ahc_platform_flushwork(ahc); 5651 ahc->flags &= ~AHC_ALL_INTERRUPTS; 5652} 5653 5654#ifdef CONFIG_PM 5655int 5656ahc_suspend(struct ahc_softc *ahc) 5657{ 5658 5659 ahc_pause_and_flushwork(ahc); 5660 5661 if (LIST_FIRST(&ahc->pending_scbs) != NULL) { 5662 ahc_unpause(ahc); 5663 return (EBUSY); 5664 } 5665 5666#ifdef AHC_TARGET_MODE 5667 /* 5668 * XXX What about ATIOs that have not yet been serviced? 5669 * Perhaps we should just refuse to be suspended if we 5670 * are acting in a target role. 5671 */ 5672 if (ahc->pending_device != NULL) { 5673 ahc_unpause(ahc); 5674 return (EBUSY); 5675 } 5676#endif 5677 ahc_shutdown(ahc); 5678 return (0); 5679} 5680 5681int 5682ahc_resume(struct ahc_softc *ahc) 5683{ 5684 5685 ahc_reset(ahc, /*reinit*/TRUE); 5686 ahc_intr_enable(ahc, TRUE); 5687 ahc_restart(ahc); 5688 return (0); 5689} 5690#endif 5691/************************** Busy Target Table *********************************/ 5692/* 5693 * Return the untagged transaction id for a given target/channel lun. 5694 * Optionally, clear the entry. 5695 */ 5696static u_int 5697ahc_index_busy_tcl(struct ahc_softc *ahc, u_int tcl) 5698{ 5699 u_int scbid; 5700 u_int target_offset; 5701 5702 if ((ahc->flags & AHC_SCB_BTT) != 0) { 5703 u_int saved_scbptr; 5704 5705 saved_scbptr = ahc_inb(ahc, SCBPTR); 5706 ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); 5707 scbid = ahc_inb(ahc, SCB_64_BTT + TCL_TARGET_OFFSET(tcl)); 5708 ahc_outb(ahc, SCBPTR, saved_scbptr); 5709 } else { 5710 target_offset = TCL_TARGET_OFFSET(tcl); 5711 scbid = ahc_inb(ahc, BUSY_TARGETS + target_offset); 5712 } 5713 5714 return (scbid); 5715} 5716 5717static void 5718ahc_unbusy_tcl(struct ahc_softc *ahc, u_int tcl) 5719{ 5720 u_int target_offset; 5721 5722 if ((ahc->flags & AHC_SCB_BTT) != 0) { 5723 u_int saved_scbptr; 5724 5725 saved_scbptr = ahc_inb(ahc, SCBPTR); 5726 ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); 5727 ahc_outb(ahc, SCB_64_BTT+TCL_TARGET_OFFSET(tcl), SCB_LIST_NULL); 5728 ahc_outb(ahc, SCBPTR, saved_scbptr); 5729 } else { 5730 target_offset = TCL_TARGET_OFFSET(tcl); 5731 ahc_outb(ahc, BUSY_TARGETS + target_offset, SCB_LIST_NULL); 5732 } 5733} 5734 5735static void 5736ahc_busy_tcl(struct ahc_softc *ahc, u_int tcl, u_int scbid) 5737{ 5738 u_int target_offset; 5739 5740 if ((ahc->flags & AHC_SCB_BTT) != 0) { 5741 u_int saved_scbptr; 5742 5743 saved_scbptr = ahc_inb(ahc, SCBPTR); 5744 ahc_outb(ahc, SCBPTR, TCL_LUN(tcl)); 5745 ahc_outb(ahc, SCB_64_BTT + TCL_TARGET_OFFSET(tcl), scbid); 5746 ahc_outb(ahc, SCBPTR, saved_scbptr); 5747 } else { 5748 target_offset = TCL_TARGET_OFFSET(tcl); 5749 ahc_outb(ahc, BUSY_TARGETS + target_offset, scbid); 5750 } 5751} 5752 5753/************************** SCB and SCB queue management **********************/ 5754int 5755ahc_match_scb(struct ahc_softc *ahc, struct scb *scb, int target, 5756 char channel, int lun, u_int tag, role_t role) 5757{ 5758 int targ = SCB_GET_TARGET(ahc, scb); 5759 char chan = SCB_GET_CHANNEL(ahc, scb); 5760 int slun = SCB_GET_LUN(scb); 5761 int match; 5762 5763 match = ((chan == channel) || (channel == ALL_CHANNELS)); 5764 if (match != 0) 5765 match = ((targ == target) || (target == CAM_TARGET_WILDCARD)); 5766 if (match != 0) 5767 match = ((lun == slun) || (lun == CAM_LUN_WILDCARD)); 5768 if (match != 0) { 5769#ifdef AHC_TARGET_MODE 5770 int group; 5771 5772 group = XPT_FC_GROUP(scb->io_ctx->ccb_h.func_code); 5773 if (role == ROLE_INITIATOR) { 5774 match = (group != XPT_FC_GROUP_TMODE) 5775 && ((tag == scb->hscb->tag) 5776 || (tag == SCB_LIST_NULL)); 5777 } else if (role == ROLE_TARGET) { 5778 match = (group == XPT_FC_GROUP_TMODE) 5779 && ((tag == scb->io_ctx->csio.tag_id) 5780 || (tag == SCB_LIST_NULL)); 5781 } 5782#else /* !AHC_TARGET_MODE */ 5783 match = ((tag == scb->hscb->tag) || (tag == SCB_LIST_NULL)); 5784#endif /* AHC_TARGET_MODE */ 5785 } 5786 5787 return match; 5788} 5789 5790static void 5791ahc_freeze_devq(struct ahc_softc *ahc, struct scb *scb) 5792{ 5793 int target; 5794 char channel; 5795 int lun; 5796 5797 target = SCB_GET_TARGET(ahc, scb); 5798 lun = SCB_GET_LUN(scb); 5799 channel = SCB_GET_CHANNEL(ahc, scb); 5800 5801 ahc_search_qinfifo(ahc, target, channel, lun, 5802 /*tag*/SCB_LIST_NULL, ROLE_UNKNOWN, 5803 CAM_REQUEUE_REQ, SEARCH_COMPLETE); 5804 5805 ahc_platform_freeze_devq(ahc, scb); 5806} 5807 5808void 5809ahc_qinfifo_requeue_tail(struct ahc_softc *ahc, struct scb *scb) 5810{ 5811 struct scb *prev_scb; 5812 5813 prev_scb = NULL; 5814 if (ahc_qinfifo_count(ahc) != 0) { 5815 u_int prev_tag; 5816 uint8_t prev_pos; 5817 5818 prev_pos = ahc->qinfifonext - 1; 5819 prev_tag = ahc->qinfifo[prev_pos]; 5820 prev_scb = ahc_lookup_scb(ahc, prev_tag); 5821 } 5822 ahc_qinfifo_requeue(ahc, prev_scb, scb); 5823 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 5824 ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); 5825 } else { 5826 ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); 5827 } 5828} 5829 5830static void 5831ahc_qinfifo_requeue(struct ahc_softc *ahc, struct scb *prev_scb, 5832 struct scb *scb) 5833{ 5834 if (prev_scb == NULL) { 5835 ahc_outb(ahc, NEXT_QUEUED_SCB, scb->hscb->tag); 5836 } else { 5837 prev_scb->hscb->next = scb->hscb->tag; 5838 ahc_sync_scb(ahc, prev_scb, 5839 BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); 5840 } 5841 ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag; 5842 scb->hscb->next = ahc->next_queued_scb->hscb->tag; 5843 ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE); 5844} 5845 5846static int 5847ahc_qinfifo_count(struct ahc_softc *ahc) 5848{ 5849 uint8_t qinpos; 5850 uint8_t diff; 5851 5852 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 5853 qinpos = ahc_inb(ahc, SNSCB_QOFF); 5854 ahc_outb(ahc, SNSCB_QOFF, qinpos); 5855 } else 5856 qinpos = ahc_inb(ahc, QINPOS); 5857 diff = ahc->qinfifonext - qinpos; 5858 return (diff); 5859} 5860 5861int 5862ahc_search_qinfifo(struct ahc_softc *ahc, int target, char channel, 5863 int lun, u_int tag, role_t role, uint32_t status, 5864 ahc_search_action action) 5865{ 5866 struct scb *scb; 5867 struct scb *prev_scb; 5868 uint8_t qinstart; 5869 uint8_t qinpos; 5870 uint8_t qintail; 5871 uint8_t next; 5872 uint8_t prev; 5873 uint8_t curscbptr; 5874 int found; 5875 int have_qregs; 5876 5877 qintail = ahc->qinfifonext; 5878 have_qregs = (ahc->features & AHC_QUEUE_REGS) != 0; 5879 if (have_qregs) { 5880 qinstart = ahc_inb(ahc, SNSCB_QOFF); 5881 ahc_outb(ahc, SNSCB_QOFF, qinstart); 5882 } else 5883 qinstart = ahc_inb(ahc, QINPOS); 5884 qinpos = qinstart; 5885 found = 0; 5886 prev_scb = NULL; 5887 5888 if (action == SEARCH_COMPLETE) { 5889 /* 5890 * Don't attempt to run any queued untagged transactions 5891 * until we are done with the abort process. 5892 */ 5893 ahc_freeze_untagged_queues(ahc); 5894 } 5895 5896 /* 5897 * Start with an empty queue. Entries that are not chosen 5898 * for removal will be re-added to the queue as we go. 5899 */ 5900 ahc->qinfifonext = qinpos; 5901 ahc_outb(ahc, NEXT_QUEUED_SCB, ahc->next_queued_scb->hscb->tag); 5902 5903 while (qinpos != qintail) { 5904 scb = ahc_lookup_scb(ahc, ahc->qinfifo[qinpos]); 5905 if (scb == NULL) { 5906 printk("qinpos = %d, SCB index = %d\n", 5907 qinpos, ahc->qinfifo[qinpos]); 5908 panic("Loop 1\n"); 5909 } 5910 5911 if (ahc_match_scb(ahc, scb, target, channel, lun, tag, role)) { 5912 /* 5913 * We found an scb that needs to be acted on. 5914 */ 5915 found++; 5916 switch (action) { 5917 case SEARCH_COMPLETE: 5918 { 5919 cam_status ostat; 5920 cam_status cstat; 5921 5922 ostat = ahc_get_transaction_status(scb); 5923 if (ostat == CAM_REQ_INPROG) 5924 ahc_set_transaction_status(scb, status); 5925 cstat = ahc_get_transaction_status(scb); 5926 if (cstat != CAM_REQ_CMP) 5927 ahc_freeze_scb(scb); 5928 if ((scb->flags & SCB_ACTIVE) == 0) 5929 printk("Inactive SCB in qinfifo\n"); 5930 ahc_done(ahc, scb); 5931 5932 /* FALLTHROUGH */ 5933 } 5934 case SEARCH_REMOVE: 5935 break; 5936 case SEARCH_COUNT: 5937 ahc_qinfifo_requeue(ahc, prev_scb, scb); 5938 prev_scb = scb; 5939 break; 5940 } 5941 } else { 5942 ahc_qinfifo_requeue(ahc, prev_scb, scb); 5943 prev_scb = scb; 5944 } 5945 qinpos++; 5946 } 5947 5948 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 5949 ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext); 5950 } else { 5951 ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext); 5952 } 5953 5954 if (action != SEARCH_COUNT 5955 && (found != 0) 5956 && (qinstart != ahc->qinfifonext)) { 5957 /* 5958 * The sequencer may be in the process of dmaing 5959 * down the SCB at the beginning of the queue. 5960 * This could be problematic if either the first, 5961 * or the second SCB is removed from the queue 5962 * (the first SCB includes a pointer to the "next" 5963 * SCB to dma). If we have removed any entries, swap 5964 * the first element in the queue with the next HSCB 5965 * so the sequencer will notice that NEXT_QUEUED_SCB 5966 * has changed during its dma attempt and will retry 5967 * the DMA. 5968 */ 5969 scb = ahc_lookup_scb(ahc, ahc->qinfifo[qinstart]); 5970 5971 if (scb == NULL) { 5972 printk("found = %d, qinstart = %d, qinfifionext = %d\n", 5973 found, qinstart, ahc->qinfifonext); 5974 panic("First/Second Qinfifo fixup\n"); 5975 } 5976 /* 5977 * ahc_swap_with_next_hscb forces our next pointer to 5978 * point to the reserved SCB for future commands. Save 5979 * and restore our original next pointer to maintain 5980 * queue integrity. 5981 */ 5982 next = scb->hscb->next; 5983 ahc->scb_data->scbindex[scb->hscb->tag] = NULL; 5984 ahc_swap_with_next_hscb(ahc, scb); 5985 scb->hscb->next = next; 5986 ahc->qinfifo[qinstart] = scb->hscb->tag; 5987 5988 /* Tell the card about the new head of the qinfifo. */ 5989 ahc_outb(ahc, NEXT_QUEUED_SCB, scb->hscb->tag); 5990 5991 /* Fixup the tail "next" pointer. */ 5992 qintail = ahc->qinfifonext - 1; 5993 scb = ahc_lookup_scb(ahc, ahc->qinfifo[qintail]); 5994 scb->hscb->next = ahc->next_queued_scb->hscb->tag; 5995 } 5996 5997 /* 5998 * Search waiting for selection list. 5999 */ 6000 curscbptr = ahc_inb(ahc, SCBPTR); 6001 next = ahc_inb(ahc, WAITING_SCBH); /* Start at head of list. */ 6002 prev = SCB_LIST_NULL; 6003 6004 while (next != SCB_LIST_NULL) { 6005 uint8_t scb_index; 6006 6007 ahc_outb(ahc, SCBPTR, next); 6008 scb_index = ahc_inb(ahc, SCB_TAG); 6009 if (scb_index >= ahc->scb_data->numscbs) { 6010 printk("Waiting List inconsistency. " 6011 "SCB index == %d, yet numscbs == %d.", 6012 scb_index, ahc->scb_data->numscbs); 6013 ahc_dump_card_state(ahc); 6014 panic("for safety"); 6015 } 6016 scb = ahc_lookup_scb(ahc, scb_index); 6017 if (scb == NULL) { 6018 printk("scb_index = %d, next = %d\n", 6019 scb_index, next); 6020 panic("Waiting List traversal\n"); 6021 } 6022 if (ahc_match_scb(ahc, scb, target, channel, 6023 lun, SCB_LIST_NULL, role)) { 6024 /* 6025 * We found an scb that needs to be acted on. 6026 */ 6027 found++; 6028 switch (action) { 6029 case SEARCH_COMPLETE: 6030 { 6031 cam_status ostat; 6032 cam_status cstat; 6033 6034 ostat = ahc_get_transaction_status(scb); 6035 if (ostat == CAM_REQ_INPROG) 6036 ahc_set_transaction_status(scb, 6037 status); 6038 cstat = ahc_get_transaction_status(scb); 6039 if (cstat != CAM_REQ_CMP) 6040 ahc_freeze_scb(scb); 6041 if ((scb->flags & SCB_ACTIVE) == 0) 6042 printk("Inactive SCB in Waiting List\n"); 6043 ahc_done(ahc, scb); 6044 /* FALLTHROUGH */ 6045 } 6046 case SEARCH_REMOVE: 6047 next = ahc_rem_wscb(ahc, next, prev); 6048 break; 6049 case SEARCH_COUNT: 6050 prev = next; 6051 next = ahc_inb(ahc, SCB_NEXT); 6052 break; 6053 } 6054 } else { 6055 6056 prev = next; 6057 next = ahc_inb(ahc, SCB_NEXT); 6058 } 6059 } 6060 ahc_outb(ahc, SCBPTR, curscbptr); 6061 6062 found += ahc_search_untagged_queues(ahc, /*ahc_io_ctx_t*/NULL, target, 6063 channel, lun, status, action); 6064 6065 if (action == SEARCH_COMPLETE) 6066 ahc_release_untagged_queues(ahc); 6067 return (found); 6068} 6069 6070int 6071ahc_search_untagged_queues(struct ahc_softc *ahc, ahc_io_ctx_t ctx, 6072 int target, char channel, int lun, uint32_t status, 6073 ahc_search_action action) 6074{ 6075 struct scb *scb; 6076 int maxtarget; 6077 int found; 6078 int i; 6079 6080 if (action == SEARCH_COMPLETE) { 6081 /* 6082 * Don't attempt to run any queued untagged transactions 6083 * until we are done with the abort process. 6084 */ 6085 ahc_freeze_untagged_queues(ahc); 6086 } 6087 6088 found = 0; 6089 i = 0; 6090 if ((ahc->flags & AHC_SCB_BTT) == 0) { 6091 6092 maxtarget = 16; 6093 if (target != CAM_TARGET_WILDCARD) { 6094 6095 i = target; 6096 if (channel == 'B') 6097 i += 8; 6098 maxtarget = i + 1; 6099 } 6100 } else { 6101 maxtarget = 0; 6102 } 6103 6104 for (; i < maxtarget; i++) { 6105 struct scb_tailq *untagged_q; 6106 struct scb *next_scb; 6107 6108 untagged_q = &(ahc->untagged_queues[i]); 6109 next_scb = TAILQ_FIRST(untagged_q); 6110 while (next_scb != NULL) { 6111 6112 scb = next_scb; 6113 next_scb = TAILQ_NEXT(scb, links.tqe); 6114 6115 /* 6116 * The head of the list may be the currently 6117 * active untagged command for a device. 6118 * We're only searching for commands that 6119 * have not been started. A transaction 6120 * marked active but still in the qinfifo 6121 * is removed by the qinfifo scanning code 6122 * above. 6123 */ 6124 if ((scb->flags & SCB_ACTIVE) != 0) 6125 continue; 6126 6127 if (ahc_match_scb(ahc, scb, target, channel, lun, 6128 SCB_LIST_NULL, ROLE_INITIATOR) == 0 6129 || (ctx != NULL && ctx != scb->io_ctx)) 6130 continue; 6131 6132 /* 6133 * We found an scb that needs to be acted on. 6134 */ 6135 found++; 6136 switch (action) { 6137 case SEARCH_COMPLETE: 6138 { 6139 cam_status ostat; 6140 cam_status cstat; 6141 6142 ostat = ahc_get_transaction_status(scb); 6143 if (ostat == CAM_REQ_INPROG) 6144 ahc_set_transaction_status(scb, status); 6145 cstat = ahc_get_transaction_status(scb); 6146 if (cstat != CAM_REQ_CMP) 6147 ahc_freeze_scb(scb); 6148 if ((scb->flags & SCB_ACTIVE) == 0) 6149 printk("Inactive SCB in untaggedQ\n"); 6150 ahc_done(ahc, scb); 6151 break; 6152 } 6153 case SEARCH_REMOVE: 6154 scb->flags &= ~SCB_UNTAGGEDQ; 6155 TAILQ_REMOVE(untagged_q, scb, links.tqe); 6156 break; 6157 case SEARCH_COUNT: 6158 break; 6159 } 6160 } 6161 } 6162 6163 if (action == SEARCH_COMPLETE) 6164 ahc_release_untagged_queues(ahc); 6165 return (found); 6166} 6167 6168int 6169ahc_search_disc_list(struct ahc_softc *ahc, int target, char channel, 6170 int lun, u_int tag, int stop_on_first, int remove, 6171 int save_state) 6172{ 6173 struct scb *scbp; 6174 u_int next; 6175 u_int prev; 6176 u_int count; 6177 u_int active_scb; 6178 6179 count = 0; 6180 next = ahc_inb(ahc, DISCONNECTED_SCBH); 6181 prev = SCB_LIST_NULL; 6182 6183 if (save_state) { 6184 /* restore this when we're done */ 6185 active_scb = ahc_inb(ahc, SCBPTR); 6186 } else 6187 /* Silence compiler */ 6188 active_scb = SCB_LIST_NULL; 6189 6190 while (next != SCB_LIST_NULL) { 6191 u_int scb_index; 6192 6193 ahc_outb(ahc, SCBPTR, next); 6194 scb_index = ahc_inb(ahc, SCB_TAG); 6195 if (scb_index >= ahc->scb_data->numscbs) { 6196 printk("Disconnected List inconsistency. " 6197 "SCB index == %d, yet numscbs == %d.", 6198 scb_index, ahc->scb_data->numscbs); 6199 ahc_dump_card_state(ahc); 6200 panic("for safety"); 6201 } 6202 6203 if (next == prev) { 6204 panic("Disconnected List Loop. " 6205 "cur SCBPTR == %x, prev SCBPTR == %x.", 6206 next, prev); 6207 } 6208 scbp = ahc_lookup_scb(ahc, scb_index); 6209 if (ahc_match_scb(ahc, scbp, target, channel, lun, 6210 tag, ROLE_INITIATOR)) { 6211 count++; 6212 if (remove) { 6213 next = 6214 ahc_rem_scb_from_disc_list(ahc, prev, next); 6215 } else { 6216 prev = next; 6217 next = ahc_inb(ahc, SCB_NEXT); 6218 } 6219 if (stop_on_first) 6220 break; 6221 } else { 6222 prev = next; 6223 next = ahc_inb(ahc, SCB_NEXT); 6224 } 6225 } 6226 if (save_state) 6227 ahc_outb(ahc, SCBPTR, active_scb); 6228 return (count); 6229} 6230 6231/* 6232 * Remove an SCB from the on chip list of disconnected transactions. 6233 * This is empty/unused if we are not performing SCB paging. 6234 */ 6235static u_int 6236ahc_rem_scb_from_disc_list(struct ahc_softc *ahc, u_int prev, u_int scbptr) 6237{ 6238 u_int next; 6239 6240 ahc_outb(ahc, SCBPTR, scbptr); 6241 next = ahc_inb(ahc, SCB_NEXT); 6242 6243 ahc_outb(ahc, SCB_CONTROL, 0); 6244 6245 ahc_add_curscb_to_free_list(ahc); 6246 6247 if (prev != SCB_LIST_NULL) { 6248 ahc_outb(ahc, SCBPTR, prev); 6249 ahc_outb(ahc, SCB_NEXT, next); 6250 } else 6251 ahc_outb(ahc, DISCONNECTED_SCBH, next); 6252 6253 return (next); 6254} 6255 6256/* 6257 * Add the SCB as selected by SCBPTR onto the on chip list of 6258 * free hardware SCBs. This list is empty/unused if we are not 6259 * performing SCB paging. 6260 */ 6261static void 6262ahc_add_curscb_to_free_list(struct ahc_softc *ahc) 6263{ 6264 /* 6265 * Invalidate the tag so that our abort 6266 * routines don't think it's active. 6267 */ 6268 ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); 6269 6270 if ((ahc->flags & AHC_PAGESCBS) != 0) { 6271 ahc_outb(ahc, SCB_NEXT, ahc_inb(ahc, FREE_SCBH)); 6272 ahc_outb(ahc, FREE_SCBH, ahc_inb(ahc, SCBPTR)); 6273 } 6274} 6275 6276/* 6277 * Manipulate the waiting for selection list and return the 6278 * scb that follows the one that we remove. 6279 */ 6280static u_int 6281ahc_rem_wscb(struct ahc_softc *ahc, u_int scbpos, u_int prev) 6282{ 6283 u_int curscb, next; 6284 6285 /* 6286 * Select the SCB we want to abort and 6287 * pull the next pointer out of it. 6288 */ 6289 curscb = ahc_inb(ahc, SCBPTR); 6290 ahc_outb(ahc, SCBPTR, scbpos); 6291 next = ahc_inb(ahc, SCB_NEXT); 6292 6293 /* Clear the necessary fields */ 6294 ahc_outb(ahc, SCB_CONTROL, 0); 6295 6296 ahc_add_curscb_to_free_list(ahc); 6297 6298 /* update the waiting list */ 6299 if (prev == SCB_LIST_NULL) { 6300 /* First in the list */ 6301 ahc_outb(ahc, WAITING_SCBH, next); 6302 6303 /* 6304 * Ensure we aren't attempting to perform 6305 * selection for this entry. 6306 */ 6307 ahc_outb(ahc, SCSISEQ, (ahc_inb(ahc, SCSISEQ) & ~ENSELO)); 6308 } else { 6309 /* 6310 * Select the scb that pointed to us 6311 * and update its next pointer. 6312 */ 6313 ahc_outb(ahc, SCBPTR, prev); 6314 ahc_outb(ahc, SCB_NEXT, next); 6315 } 6316 6317 /* 6318 * Point us back at the original scb position. 6319 */ 6320 ahc_outb(ahc, SCBPTR, curscb); 6321 return next; 6322} 6323 6324/******************************** Error Handling ******************************/ 6325/* 6326 * Abort all SCBs that match the given description (target/channel/lun/tag), 6327 * setting their status to the passed in status if the status has not already 6328 * been modified from CAM_REQ_INPROG. This routine assumes that the sequencer 6329 * is paused before it is called. 6330 */ 6331static int 6332ahc_abort_scbs(struct ahc_softc *ahc, int target, char channel, 6333 int lun, u_int tag, role_t role, uint32_t status) 6334{ 6335 struct scb *scbp; 6336 struct scb *scbp_next; 6337 u_int active_scb; 6338 int i, j; 6339 int maxtarget; 6340 int minlun; 6341 int maxlun; 6342 6343 int found; 6344 6345 /* 6346 * Don't attempt to run any queued untagged transactions 6347 * until we are done with the abort process. 6348 */ 6349 ahc_freeze_untagged_queues(ahc); 6350 6351 /* restore this when we're done */ 6352 active_scb = ahc_inb(ahc, SCBPTR); 6353 6354 found = ahc_search_qinfifo(ahc, target, channel, lun, SCB_LIST_NULL, 6355 role, CAM_REQUEUE_REQ, SEARCH_COMPLETE); 6356 6357 /* 6358 * Clean out the busy target table for any untagged commands. 6359 */ 6360 i = 0; 6361 maxtarget = 16; 6362 if (target != CAM_TARGET_WILDCARD) { 6363 i = target; 6364 if (channel == 'B') 6365 i += 8; 6366 maxtarget = i + 1; 6367 } 6368 6369 if (lun == CAM_LUN_WILDCARD) { 6370 6371 /* 6372 * Unless we are using an SCB based 6373 * busy targets table, there is only 6374 * one table entry for all luns of 6375 * a target. 6376 */ 6377 minlun = 0; 6378 maxlun = 1; 6379 if ((ahc->flags & AHC_SCB_BTT) != 0) 6380 maxlun = AHC_NUM_LUNS; 6381 } else { 6382 minlun = lun; 6383 maxlun = lun + 1; 6384 } 6385 6386 if (role != ROLE_TARGET) { 6387 for (;i < maxtarget; i++) { 6388 for (j = minlun;j < maxlun; j++) { 6389 u_int scbid; 6390 u_int tcl; 6391 6392 tcl = BUILD_TCL(i << 4, j); 6393 scbid = ahc_index_busy_tcl(ahc, tcl); 6394 scbp = ahc_lookup_scb(ahc, scbid); 6395 if (scbp == NULL 6396 || ahc_match_scb(ahc, scbp, target, channel, 6397 lun, tag, role) == 0) 6398 continue; 6399 ahc_unbusy_tcl(ahc, BUILD_TCL(i << 4, j)); 6400 } 6401 } 6402 6403 /* 6404 * Go through the disconnected list and remove any entries we 6405 * have queued for completion, 0'ing their control byte too. 6406 * We save the active SCB and restore it ourselves, so there 6407 * is no reason for this search to restore it too. 6408 */ 6409 ahc_search_disc_list(ahc, target, channel, lun, tag, 6410 /*stop_on_first*/FALSE, /*remove*/TRUE, 6411 /*save_state*/FALSE); 6412 } 6413 6414 /* 6415 * Go through the hardware SCB array looking for commands that 6416 * were active but not on any list. In some cases, these remnants 6417 * might not still have mappings in the scbindex array (e.g. unexpected 6418 * bus free with the same scb queued for an abort). Don't hold this 6419 * against them. 6420 */ 6421 for (i = 0; i < ahc->scb_data->maxhscbs; i++) { 6422 u_int scbid; 6423 6424 ahc_outb(ahc, SCBPTR, i); 6425 scbid = ahc_inb(ahc, SCB_TAG); 6426 scbp = ahc_lookup_scb(ahc, scbid); 6427 if ((scbp == NULL && scbid != SCB_LIST_NULL) 6428 || (scbp != NULL 6429 && ahc_match_scb(ahc, scbp, target, channel, lun, tag, role))) 6430 ahc_add_curscb_to_free_list(ahc); 6431 } 6432 6433 /* 6434 * Go through the pending CCB list and look for 6435 * commands for this target that are still active. 6436 * These are other tagged commands that were 6437 * disconnected when the reset occurred. 6438 */ 6439 scbp_next = LIST_FIRST(&ahc->pending_scbs); 6440 while (scbp_next != NULL) { 6441 scbp = scbp_next; 6442 scbp_next = LIST_NEXT(scbp, pending_links); 6443 if (ahc_match_scb(ahc, scbp, target, channel, lun, tag, role)) { 6444 cam_status ostat; 6445 6446 ostat = ahc_get_transaction_status(scbp); 6447 if (ostat == CAM_REQ_INPROG) 6448 ahc_set_transaction_status(scbp, status); 6449 if (ahc_get_transaction_status(scbp) != CAM_REQ_CMP) 6450 ahc_freeze_scb(scbp); 6451 if ((scbp->flags & SCB_ACTIVE) == 0) 6452 printk("Inactive SCB on pending list\n"); 6453 ahc_done(ahc, scbp); 6454 found++; 6455 } 6456 } 6457 ahc_outb(ahc, SCBPTR, active_scb); 6458 ahc_platform_abort_scbs(ahc, target, channel, lun, tag, role, status); 6459 ahc_release_untagged_queues(ahc); 6460 return found; 6461} 6462 6463static void 6464ahc_reset_current_bus(struct ahc_softc *ahc) 6465{ 6466 uint8_t scsiseq; 6467 6468 ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENSCSIRST); 6469 scsiseq = ahc_inb(ahc, SCSISEQ); 6470 ahc_outb(ahc, SCSISEQ, scsiseq | SCSIRSTO); 6471 ahc_flush_device_writes(ahc); 6472 ahc_delay(AHC_BUSRESET_DELAY); 6473 /* Turn off the bus reset */ 6474 ahc_outb(ahc, SCSISEQ, scsiseq & ~SCSIRSTO); 6475 6476 ahc_clear_intstat(ahc); 6477 6478 /* Re-enable reset interrupts */ 6479 ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) | ENSCSIRST); 6480} 6481 6482int 6483ahc_reset_channel(struct ahc_softc *ahc, char channel, int initiate_reset) 6484{ 6485 struct ahc_devinfo devinfo; 6486 u_int initiator, target, max_scsiid; 6487 u_int sblkctl; 6488 u_int scsiseq; 6489 u_int simode1; 6490 int found; 6491 int restart_needed; 6492 char cur_channel; 6493 6494 ahc->pending_device = NULL; 6495 6496 ahc_compile_devinfo(&devinfo, 6497 CAM_TARGET_WILDCARD, 6498 CAM_TARGET_WILDCARD, 6499 CAM_LUN_WILDCARD, 6500 channel, ROLE_UNKNOWN); 6501 ahc_pause(ahc); 6502 6503 /* Make sure the sequencer is in a safe location. */ 6504 ahc_clear_critical_section(ahc); 6505 6506 /* 6507 * Run our command complete fifos to ensure that we perform 6508 * completion processing on any commands that 'completed' 6509 * before the reset occurred. 6510 */ 6511 ahc_run_qoutfifo(ahc); 6512#ifdef AHC_TARGET_MODE 6513 /* 6514 * XXX - In Twin mode, the tqinfifo may have commands 6515 * for an unaffected channel in it. However, if 6516 * we have run out of ATIO resources to drain that 6517 * queue, we may not get them all out here. Further, 6518 * the blocked transactions for the reset channel 6519 * should just be killed off, irrespecitve of whether 6520 * we are blocked on ATIO resources. Write a routine 6521 * to compact the tqinfifo appropriately. 6522 */ 6523 if ((ahc->flags & AHC_TARGETROLE) != 0) { 6524 ahc_run_tqinfifo(ahc, /*paused*/TRUE); 6525 } 6526#endif 6527 6528 /* 6529 * Reset the bus if we are initiating this reset 6530 */ 6531 sblkctl = ahc_inb(ahc, SBLKCTL); 6532 cur_channel = 'A'; 6533 if ((ahc->features & AHC_TWIN) != 0 6534 && ((sblkctl & SELBUSB) != 0)) 6535 cur_channel = 'B'; 6536 scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); 6537 if (cur_channel != channel) { 6538 /* Case 1: Command for another bus is active 6539 * Stealthily reset the other bus without 6540 * upsetting the current bus. 6541 */ 6542 ahc_outb(ahc, SBLKCTL, sblkctl ^ SELBUSB); 6543 simode1 = ahc_inb(ahc, SIMODE1) & ~(ENBUSFREE|ENSCSIRST); 6544#ifdef AHC_TARGET_MODE 6545 /* 6546 * Bus resets clear ENSELI, so we cannot 6547 * defer re-enabling bus reset interrupts 6548 * if we are in target mode. 6549 */ 6550 if ((ahc->flags & AHC_TARGETROLE) != 0) 6551 simode1 |= ENSCSIRST; 6552#endif 6553 ahc_outb(ahc, SIMODE1, simode1); 6554 if (initiate_reset) 6555 ahc_reset_current_bus(ahc); 6556 ahc_clear_intstat(ahc); 6557 ahc_outb(ahc, SCSISEQ, scsiseq & (ENSELI|ENRSELI|ENAUTOATNP)); 6558 ahc_outb(ahc, SBLKCTL, sblkctl); 6559 restart_needed = FALSE; 6560 } else { 6561 /* Case 2: A command from this bus is active or we're idle */ 6562 simode1 = ahc_inb(ahc, SIMODE1) & ~(ENBUSFREE|ENSCSIRST); 6563#ifdef AHC_TARGET_MODE 6564 /* 6565 * Bus resets clear ENSELI, so we cannot 6566 * defer re-enabling bus reset interrupts 6567 * if we are in target mode. 6568 */ 6569 if ((ahc->flags & AHC_TARGETROLE) != 0) 6570 simode1 |= ENSCSIRST; 6571#endif 6572 ahc_outb(ahc, SIMODE1, simode1); 6573 if (initiate_reset) 6574 ahc_reset_current_bus(ahc); 6575 ahc_clear_intstat(ahc); 6576 ahc_outb(ahc, SCSISEQ, scsiseq & (ENSELI|ENRSELI|ENAUTOATNP)); 6577 restart_needed = TRUE; 6578 } 6579 6580 /* 6581 * Clean up all the state information for the 6582 * pending transactions on this bus. 6583 */ 6584 found = ahc_abort_scbs(ahc, CAM_TARGET_WILDCARD, channel, 6585 CAM_LUN_WILDCARD, SCB_LIST_NULL, 6586 ROLE_UNKNOWN, CAM_SCSI_BUS_RESET); 6587 6588 max_scsiid = (ahc->features & AHC_WIDE) ? 15 : 7; 6589 6590#ifdef AHC_TARGET_MODE 6591 /* 6592 * Send an immediate notify ccb to all target more peripheral 6593 * drivers affected by this action. 6594 */ 6595 for (target = 0; target <= max_scsiid; target++) { 6596 struct ahc_tmode_tstate* tstate; 6597 u_int lun; 6598 6599 tstate = ahc->enabled_targets[target]; 6600 if (tstate == NULL) 6601 continue; 6602 for (lun = 0; lun < AHC_NUM_LUNS; lun++) { 6603 struct ahc_tmode_lstate* lstate; 6604 6605 lstate = tstate->enabled_luns[lun]; 6606 if (lstate == NULL) 6607 continue; 6608 6609 ahc_queue_lstate_event(ahc, lstate, CAM_TARGET_WILDCARD, 6610 EVENT_TYPE_BUS_RESET, /*arg*/0); 6611 ahc_send_lstate_events(ahc, lstate); 6612 } 6613 } 6614#endif 6615 /* Notify the XPT that a bus reset occurred */ 6616 ahc_send_async(ahc, devinfo.channel, CAM_TARGET_WILDCARD, 6617 CAM_LUN_WILDCARD, AC_BUS_RESET); 6618 6619 /* 6620 * Revert to async/narrow transfers until we renegotiate. 6621 */ 6622 for (target = 0; target <= max_scsiid; target++) { 6623 6624 if (ahc->enabled_targets[target] == NULL) 6625 continue; 6626 for (initiator = 0; initiator <= max_scsiid; initiator++) { 6627 struct ahc_devinfo devinfo; 6628 6629 ahc_compile_devinfo(&devinfo, target, initiator, 6630 CAM_LUN_WILDCARD, 6631 channel, ROLE_UNKNOWN); 6632 ahc_set_width(ahc, &devinfo, MSG_EXT_WDTR_BUS_8_BIT, 6633 AHC_TRANS_CUR, /*paused*/TRUE); 6634 ahc_set_syncrate(ahc, &devinfo, /*syncrate*/NULL, 6635 /*period*/0, /*offset*/0, 6636 /*ppr_options*/0, AHC_TRANS_CUR, 6637 /*paused*/TRUE); 6638 } 6639 } 6640 6641 if (restart_needed) 6642 ahc_restart(ahc); 6643 else 6644 ahc_unpause(ahc); 6645 return found; 6646} 6647 6648 6649/***************************** Residual Processing ****************************/ 6650/* 6651 * Calculate the residual for a just completed SCB. 6652 */ 6653static void 6654ahc_calc_residual(struct ahc_softc *ahc, struct scb *scb) 6655{ 6656 struct hardware_scb *hscb; 6657 struct status_pkt *spkt; 6658 uint32_t sgptr; 6659 uint32_t resid_sgptr; 6660 uint32_t resid; 6661 6662 /* 6663 * 5 cases. 6664 * 1) No residual. 6665 * SG_RESID_VALID clear in sgptr. 6666 * 2) Transferless command 6667 * 3) Never performed any transfers. 6668 * sgptr has SG_FULL_RESID set. 6669 * 4) No residual but target did not 6670 * save data pointers after the 6671 * last transfer, so sgptr was 6672 * never updated. 6673 * 5) We have a partial residual. 6674 * Use residual_sgptr to determine 6675 * where we are. 6676 */ 6677 6678 hscb = scb->hscb; 6679 sgptr = ahc_le32toh(hscb->sgptr); 6680 if ((sgptr & SG_RESID_VALID) == 0) 6681 /* Case 1 */ 6682 return; 6683 sgptr &= ~SG_RESID_VALID; 6684 6685 if ((sgptr & SG_LIST_NULL) != 0) 6686 /* Case 2 */ 6687 return; 6688 6689 spkt = &hscb->shared_data.status; 6690 resid_sgptr = ahc_le32toh(spkt->residual_sg_ptr); 6691 if ((sgptr & SG_FULL_RESID) != 0) { 6692 /* Case 3 */ 6693 resid = ahc_get_transfer_length(scb); 6694 } else if ((resid_sgptr & SG_LIST_NULL) != 0) { 6695 /* Case 4 */ 6696 return; 6697 } else if ((resid_sgptr & ~SG_PTR_MASK) != 0) { 6698 panic("Bogus resid sgptr value 0x%x\n", resid_sgptr); 6699 } else { 6700 struct ahc_dma_seg *sg; 6701 6702 /* 6703 * Remainder of the SG where the transfer 6704 * stopped. 6705 */ 6706 resid = ahc_le32toh(spkt->residual_datacnt) & AHC_SG_LEN_MASK; 6707 sg = ahc_sg_bus_to_virt(scb, resid_sgptr & SG_PTR_MASK); 6708 6709 /* The residual sg_ptr always points to the next sg */ 6710 sg--; 6711 6712 /* 6713 * Add up the contents of all residual 6714 * SG segments that are after the SG where 6715 * the transfer stopped. 6716 */ 6717 while ((ahc_le32toh(sg->len) & AHC_DMA_LAST_SEG) == 0) { 6718 sg++; 6719 resid += ahc_le32toh(sg->len) & AHC_SG_LEN_MASK; 6720 } 6721 } 6722 if ((scb->flags & SCB_SENSE) == 0) 6723 ahc_set_residual(scb, resid); 6724 else 6725 ahc_set_sense_residual(scb, resid); 6726 6727#ifdef AHC_DEBUG 6728 if ((ahc_debug & AHC_SHOW_MISC) != 0) { 6729 ahc_print_path(ahc, scb); 6730 printk("Handled %sResidual of %d bytes\n", 6731 (scb->flags & SCB_SENSE) ? "Sense " : "", resid); 6732 } 6733#endif 6734} 6735 6736/******************************* Target Mode **********************************/ 6737#ifdef AHC_TARGET_MODE 6738/* 6739 * Add a target mode event to this lun's queue 6740 */ 6741static void 6742ahc_queue_lstate_event(struct ahc_softc *ahc, struct ahc_tmode_lstate *lstate, 6743 u_int initiator_id, u_int event_type, u_int event_arg) 6744{ 6745 struct ahc_tmode_event *event; 6746 int pending; 6747 6748 xpt_freeze_devq(lstate->path, /*count*/1); 6749 if (lstate->event_w_idx >= lstate->event_r_idx) 6750 pending = lstate->event_w_idx - lstate->event_r_idx; 6751 else 6752 pending = AHC_TMODE_EVENT_BUFFER_SIZE + 1 6753 - (lstate->event_r_idx - lstate->event_w_idx); 6754 6755 if (event_type == EVENT_TYPE_BUS_RESET 6756 || event_type == MSG_BUS_DEV_RESET) { 6757 /* 6758 * Any earlier events are irrelevant, so reset our buffer. 6759 * This has the effect of allowing us to deal with reset 6760 * floods (an external device holding down the reset line) 6761 * without losing the event that is really interesting. 6762 */ 6763 lstate->event_r_idx = 0; 6764 lstate->event_w_idx = 0; 6765 xpt_release_devq(lstate->path, pending, /*runqueue*/FALSE); 6766 } 6767 6768 if (pending == AHC_TMODE_EVENT_BUFFER_SIZE) { 6769 xpt_print_path(lstate->path); 6770 printk("immediate event %x:%x lost\n", 6771 lstate->event_buffer[lstate->event_r_idx].event_type, 6772 lstate->event_buffer[lstate->event_r_idx].event_arg); 6773 lstate->event_r_idx++; 6774 if (lstate->event_r_idx == AHC_TMODE_EVENT_BUFFER_SIZE) 6775 lstate->event_r_idx = 0; 6776 xpt_release_devq(lstate->path, /*count*/1, /*runqueue*/FALSE); 6777 } 6778 6779 event = &lstate->event_buffer[lstate->event_w_idx]; 6780 event->initiator_id = initiator_id; 6781 event->event_type = event_type; 6782 event->event_arg = event_arg; 6783 lstate->event_w_idx++; 6784 if (lstate->event_w_idx == AHC_TMODE_EVENT_BUFFER_SIZE) 6785 lstate->event_w_idx = 0; 6786} 6787 6788/* 6789 * Send any target mode events queued up waiting 6790 * for immediate notify resources. 6791 */ 6792void 6793ahc_send_lstate_events(struct ahc_softc *ahc, struct ahc_tmode_lstate *lstate) 6794{ 6795 struct ccb_hdr *ccbh; 6796 struct ccb_immed_notify *inot; 6797 6798 while (lstate->event_r_idx != lstate->event_w_idx 6799 && (ccbh = SLIST_FIRST(&lstate->immed_notifies)) != NULL) { 6800 struct ahc_tmode_event *event; 6801 6802 event = &lstate->event_buffer[lstate->event_r_idx]; 6803 SLIST_REMOVE_HEAD(&lstate->immed_notifies, sim_links.sle); 6804 inot = (struct ccb_immed_notify *)ccbh; 6805 switch (event->event_type) { 6806 case EVENT_TYPE_BUS_RESET: 6807 ccbh->status = CAM_SCSI_BUS_RESET|CAM_DEV_QFRZN; 6808 break; 6809 default: 6810 ccbh->status = CAM_MESSAGE_RECV|CAM_DEV_QFRZN; 6811 inot->message_args[0] = event->event_type; 6812 inot->message_args[1] = event->event_arg; 6813 break; 6814 } 6815 inot->initiator_id = event->initiator_id; 6816 inot->sense_len = 0; 6817 xpt_done((union ccb *)inot); 6818 lstate->event_r_idx++; 6819 if (lstate->event_r_idx == AHC_TMODE_EVENT_BUFFER_SIZE) 6820 lstate->event_r_idx = 0; 6821 } 6822} 6823#endif 6824 6825/******************** Sequencer Program Patching/Download *********************/ 6826 6827#ifdef AHC_DUMP_SEQ 6828void 6829ahc_dumpseq(struct ahc_softc* ahc) 6830{ 6831 int i; 6832 6833 ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); 6834 ahc_outb(ahc, SEQADDR0, 0); 6835 ahc_outb(ahc, SEQADDR1, 0); 6836 for (i = 0; i < ahc->instruction_ram_size; i++) { 6837 uint8_t ins_bytes[4]; 6838 6839 ahc_insb(ahc, SEQRAM, ins_bytes, 4); 6840 printk("0x%08x\n", ins_bytes[0] << 24 6841 | ins_bytes[1] << 16 6842 | ins_bytes[2] << 8 6843 | ins_bytes[3]); 6844 } 6845} 6846#endif 6847 6848static int 6849ahc_loadseq(struct ahc_softc *ahc) 6850{ 6851 struct cs cs_table[num_critical_sections]; 6852 u_int begin_set[num_critical_sections]; 6853 u_int end_set[num_critical_sections]; 6854 const struct patch *cur_patch; 6855 u_int cs_count; 6856 u_int cur_cs; 6857 u_int i; 6858 u_int skip_addr; 6859 u_int sg_prefetch_cnt; 6860 int downloaded; 6861 uint8_t download_consts[7]; 6862 6863 /* 6864 * Start out with 0 critical sections 6865 * that apply to this firmware load. 6866 */ 6867 cs_count = 0; 6868 cur_cs = 0; 6869 memset(begin_set, 0, sizeof(begin_set)); 6870 memset(end_set, 0, sizeof(end_set)); 6871 6872 /* Setup downloadable constant table */ 6873 download_consts[QOUTFIFO_OFFSET] = 0; 6874 if (ahc->targetcmds != NULL) 6875 download_consts[QOUTFIFO_OFFSET] += 32; 6876 download_consts[QINFIFO_OFFSET] = download_consts[QOUTFIFO_OFFSET] + 1; 6877 download_consts[CACHESIZE_MASK] = ahc->pci_cachesize - 1; 6878 download_consts[INVERTED_CACHESIZE_MASK] = ~(ahc->pci_cachesize - 1); 6879 sg_prefetch_cnt = ahc->pci_cachesize; 6880 if (sg_prefetch_cnt < (2 * sizeof(struct ahc_dma_seg))) 6881 sg_prefetch_cnt = 2 * sizeof(struct ahc_dma_seg); 6882 download_consts[SG_PREFETCH_CNT] = sg_prefetch_cnt; 6883 download_consts[SG_PREFETCH_ALIGN_MASK] = ~(sg_prefetch_cnt - 1); 6884 download_consts[SG_PREFETCH_ADDR_MASK] = (sg_prefetch_cnt - 1); 6885 6886 cur_patch = patches; 6887 downloaded = 0; 6888 skip_addr = 0; 6889 ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE|LOADRAM); 6890 ahc_outb(ahc, SEQADDR0, 0); 6891 ahc_outb(ahc, SEQADDR1, 0); 6892 6893 for (i = 0; i < sizeof(seqprog)/4; i++) { 6894 if (ahc_check_patch(ahc, &cur_patch, i, &skip_addr) == 0) { 6895 /* 6896 * Don't download this instruction as it 6897 * is in a patch that was removed. 6898 */ 6899 continue; 6900 } 6901 6902 if (downloaded == ahc->instruction_ram_size) { 6903 /* 6904 * We're about to exceed the instruction 6905 * storage capacity for this chip. Fail 6906 * the load. 6907 */ 6908 printk("\n%s: Program too large for instruction memory " 6909 "size of %d!\n", ahc_name(ahc), 6910 ahc->instruction_ram_size); 6911 return (ENOMEM); 6912 } 6913 6914 /* 6915 * Move through the CS table until we find a CS 6916 * that might apply to this instruction. 6917 */ 6918 for (; cur_cs < num_critical_sections; cur_cs++) { 6919 if (critical_sections[cur_cs].end <= i) { 6920 if (begin_set[cs_count] == TRUE 6921 && end_set[cs_count] == FALSE) { 6922 cs_table[cs_count].end = downloaded; 6923 end_set[cs_count] = TRUE; 6924 cs_count++; 6925 } 6926 continue; 6927 } 6928 if (critical_sections[cur_cs].begin <= i 6929 && begin_set[cs_count] == FALSE) { 6930 cs_table[cs_count].begin = downloaded; 6931 begin_set[cs_count] = TRUE; 6932 } 6933 break; 6934 } 6935 ahc_download_instr(ahc, i, download_consts); 6936 downloaded++; 6937 } 6938 6939 ahc->num_critical_sections = cs_count; 6940 if (cs_count != 0) { 6941 6942 cs_count *= sizeof(struct cs); 6943 ahc->critical_sections = kmalloc(cs_count, GFP_ATOMIC); 6944 if (ahc->critical_sections == NULL) 6945 panic("ahc_loadseq: Could not malloc"); 6946 memcpy(ahc->critical_sections, cs_table, cs_count); 6947 } 6948 ahc_outb(ahc, SEQCTL, PERRORDIS|FAILDIS|FASTMODE); 6949 6950 if (bootverbose) { 6951 printk(" %d instructions downloaded\n", downloaded); 6952 printk("%s: Features 0x%x, Bugs 0x%x, Flags 0x%x\n", 6953 ahc_name(ahc), ahc->features, ahc->bugs, ahc->flags); 6954 } 6955 return (0); 6956} 6957 6958static int 6959ahc_check_patch(struct ahc_softc *ahc, const struct patch **start_patch, 6960 u_int start_instr, u_int *skip_addr) 6961{ 6962 const struct patch *cur_patch; 6963 const struct patch *last_patch; 6964 u_int num_patches; 6965 6966 num_patches = ARRAY_SIZE(patches); 6967 last_patch = &patches[num_patches]; 6968 cur_patch = *start_patch; 6969 6970 while (cur_patch < last_patch && start_instr == cur_patch->begin) { 6971 6972 if (cur_patch->patch_func(ahc) == 0) { 6973 6974 /* Start rejecting code */ 6975 *skip_addr = start_instr + cur_patch->skip_instr; 6976 cur_patch += cur_patch->skip_patch; 6977 } else { 6978 /* Accepted this patch. Advance to the next 6979 * one and wait for our intruction pointer to 6980 * hit this point. 6981 */ 6982 cur_patch++; 6983 } 6984 } 6985 6986 *start_patch = cur_patch; 6987 if (start_instr < *skip_addr) 6988 /* Still skipping */ 6989 return (0); 6990 6991 return (1); 6992} 6993 6994static void 6995ahc_download_instr(struct ahc_softc *ahc, u_int instrptr, uint8_t *dconsts) 6996{ 6997 union ins_formats instr; 6998 struct ins_format1 *fmt1_ins; 6999 struct ins_format3 *fmt3_ins; 7000 u_int opcode; 7001 7002 /* 7003 * The firmware is always compiled into a little endian format. 7004 */ 7005 instr.integer = ahc_le32toh(*(uint32_t*)&seqprog[instrptr * 4]); 7006 7007 fmt1_ins = &instr.format1; 7008 fmt3_ins = NULL; 7009 7010 /* Pull the opcode */ 7011 opcode = instr.format1.opcode; 7012 switch (opcode) { 7013 case AIC_OP_JMP: 7014 case AIC_OP_JC: 7015 case AIC_OP_JNC: 7016 case AIC_OP_CALL: 7017 case AIC_OP_JNE: 7018 case AIC_OP_JNZ: 7019 case AIC_OP_JE: 7020 case AIC_OP_JZ: 7021 { 7022 const struct patch *cur_patch; 7023 int address_offset; 7024 u_int address; 7025 u_int skip_addr; 7026 u_int i; 7027 7028 fmt3_ins = &instr.format3; 7029 address_offset = 0; 7030 address = fmt3_ins->address; 7031 cur_patch = patches; 7032 skip_addr = 0; 7033 7034 for (i = 0; i < address;) { 7035 7036 ahc_check_patch(ahc, &cur_patch, i, &skip_addr); 7037 7038 if (skip_addr > i) { 7039 int end_addr; 7040 7041 end_addr = min(address, skip_addr); 7042 address_offset += end_addr - i; 7043 i = skip_addr; 7044 } else { 7045 i++; 7046 } 7047 } 7048 address -= address_offset; 7049 fmt3_ins->address = address; 7050 /* FALLTHROUGH */ 7051 } 7052 case AIC_OP_OR: 7053 case AIC_OP_AND: 7054 case AIC_OP_XOR: 7055 case AIC_OP_ADD: 7056 case AIC_OP_ADC: 7057 case AIC_OP_BMOV: 7058 if (fmt1_ins->parity != 0) { 7059 fmt1_ins->immediate = dconsts[fmt1_ins->immediate]; 7060 } 7061 fmt1_ins->parity = 0; 7062 if ((ahc->features & AHC_CMD_CHAN) == 0 7063 && opcode == AIC_OP_BMOV) { 7064 /* 7065 * Block move was added at the same time 7066 * as the command channel. Verify that 7067 * this is only a move of a single element 7068 * and convert the BMOV to a MOV 7069 * (AND with an immediate of FF). 7070 */ 7071 if (fmt1_ins->immediate != 1) 7072 panic("%s: BMOV not supported\n", 7073 ahc_name(ahc)); 7074 fmt1_ins->opcode = AIC_OP_AND; 7075 fmt1_ins->immediate = 0xff; 7076 } 7077 /* FALLTHROUGH */ 7078 case AIC_OP_ROL: 7079 if ((ahc->features & AHC_ULTRA2) != 0) { 7080 int i, count; 7081 7082 /* Calculate odd parity for the instruction */ 7083 for (i = 0, count = 0; i < 31; i++) { 7084 uint32_t mask; 7085 7086 mask = 0x01 << i; 7087 if ((instr.integer & mask) != 0) 7088 count++; 7089 } 7090 if ((count & 0x01) == 0) 7091 instr.format1.parity = 1; 7092 } else { 7093 /* Compress the instruction for older sequencers */ 7094 if (fmt3_ins != NULL) { 7095 instr.integer = 7096 fmt3_ins->immediate 7097 | (fmt3_ins->source << 8) 7098 | (fmt3_ins->address << 16) 7099 | (fmt3_ins->opcode << 25); 7100 } else { 7101 instr.integer = 7102 fmt1_ins->immediate 7103 | (fmt1_ins->source << 8) 7104 | (fmt1_ins->destination << 16) 7105 | (fmt1_ins->ret << 24) 7106 | (fmt1_ins->opcode << 25); 7107 } 7108 } 7109 /* The sequencer is a little endian cpu */ 7110 instr.integer = ahc_htole32(instr.integer); 7111 ahc_outsb(ahc, SEQRAM, instr.bytes, 4); 7112 break; 7113 default: 7114 panic("Unknown opcode encountered in seq program"); 7115 break; 7116 } 7117} 7118 7119int 7120ahc_print_register(const ahc_reg_parse_entry_t *table, u_int num_entries, 7121 const char *name, u_int address, u_int value, 7122 u_int *cur_column, u_int wrap_point) 7123{ 7124 int printed; 7125 u_int printed_mask; 7126 7127 if (cur_column != NULL && *cur_column >= wrap_point) { 7128 printk("\n"); 7129 *cur_column = 0; 7130 } 7131 printed = printk("%s[0x%x]", name, value); 7132 if (table == NULL) { 7133 printed += printk(" "); 7134 *cur_column += printed; 7135 return (printed); 7136 } 7137 printed_mask = 0; 7138 while (printed_mask != 0xFF) { 7139 int entry; 7140 7141 for (entry = 0; entry < num_entries; entry++) { 7142 if (((value & table[entry].mask) 7143 != table[entry].value) 7144 || ((printed_mask & table[entry].mask) 7145 == table[entry].mask)) 7146 continue; 7147 7148 printed += printk("%s%s", 7149 printed_mask == 0 ? ":(" : "|", 7150 table[entry].name); 7151 printed_mask |= table[entry].mask; 7152 7153 break; 7154 } 7155 if (entry >= num_entries) 7156 break; 7157 } 7158 if (printed_mask != 0) 7159 printed += printk(") "); 7160 else 7161 printed += printk(" "); 7162 if (cur_column != NULL) 7163 *cur_column += printed; 7164 return (printed); 7165} 7166 7167void 7168ahc_dump_card_state(struct ahc_softc *ahc) 7169{ 7170 struct scb *scb; 7171 struct scb_tailq *untagged_q; 7172 u_int cur_col; 7173 int paused; 7174 int target; 7175 int maxtarget; 7176 int i; 7177 uint8_t last_phase; 7178 uint8_t qinpos; 7179 uint8_t qintail; 7180 uint8_t qoutpos; 7181 uint8_t scb_index; 7182 uint8_t saved_scbptr; 7183 7184 if (ahc_is_paused(ahc)) { 7185 paused = 1; 7186 } else { 7187 paused = 0; 7188 ahc_pause(ahc); 7189 } 7190 7191 saved_scbptr = ahc_inb(ahc, SCBPTR); 7192 last_phase = ahc_inb(ahc, LASTPHASE); 7193 printk(">>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<\n" 7194 "%s: Dumping Card State %s, at SEQADDR 0x%x\n", 7195 ahc_name(ahc), ahc_lookup_phase_entry(last_phase)->phasemsg, 7196 ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8)); 7197 if (paused) 7198 printk("Card was paused\n"); 7199 printk("ACCUM = 0x%x, SINDEX = 0x%x, DINDEX = 0x%x, ARG_2 = 0x%x\n", 7200 ahc_inb(ahc, ACCUM), ahc_inb(ahc, SINDEX), ahc_inb(ahc, DINDEX), 7201 ahc_inb(ahc, ARG_2)); 7202 printk("HCNT = 0x%x SCBPTR = 0x%x\n", ahc_inb(ahc, HCNT), 7203 ahc_inb(ahc, SCBPTR)); 7204 cur_col = 0; 7205 if ((ahc->features & AHC_DT) != 0) 7206 ahc_scsiphase_print(ahc_inb(ahc, SCSIPHASE), &cur_col, 50); 7207 ahc_scsisigi_print(ahc_inb(ahc, SCSISIGI), &cur_col, 50); 7208 ahc_error_print(ahc_inb(ahc, ERROR), &cur_col, 50); 7209 ahc_scsibusl_print(ahc_inb(ahc, SCSIBUSL), &cur_col, 50); 7210 ahc_lastphase_print(ahc_inb(ahc, LASTPHASE), &cur_col, 50); 7211 ahc_scsiseq_print(ahc_inb(ahc, SCSISEQ), &cur_col, 50); 7212 ahc_sblkctl_print(ahc_inb(ahc, SBLKCTL), &cur_col, 50); 7213 ahc_scsirate_print(ahc_inb(ahc, SCSIRATE), &cur_col, 50); 7214 ahc_seqctl_print(ahc_inb(ahc, SEQCTL), &cur_col, 50); 7215 ahc_seq_flags_print(ahc_inb(ahc, SEQ_FLAGS), &cur_col, 50); 7216 ahc_sstat0_print(ahc_inb(ahc, SSTAT0), &cur_col, 50); 7217 ahc_sstat1_print(ahc_inb(ahc, SSTAT1), &cur_col, 50); 7218 ahc_sstat2_print(ahc_inb(ahc, SSTAT2), &cur_col, 50); 7219 ahc_sstat3_print(ahc_inb(ahc, SSTAT3), &cur_col, 50); 7220 ahc_simode0_print(ahc_inb(ahc, SIMODE0), &cur_col, 50); 7221 ahc_simode1_print(ahc_inb(ahc, SIMODE1), &cur_col, 50); 7222 ahc_sxfrctl0_print(ahc_inb(ahc, SXFRCTL0), &cur_col, 50); 7223 ahc_dfcntrl_print(ahc_inb(ahc, DFCNTRL), &cur_col, 50); 7224 ahc_dfstatus_print(ahc_inb(ahc, DFSTATUS), &cur_col, 50); 7225 if (cur_col != 0) 7226 printk("\n"); 7227 printk("STACK:"); 7228 for (i = 0; i < STACK_SIZE; i++) 7229 printk(" 0x%x", ahc_inb(ahc, STACK)|(ahc_inb(ahc, STACK) << 8)); 7230 printk("\nSCB count = %d\n", ahc->scb_data->numscbs); 7231 printk("Kernel NEXTQSCB = %d\n", ahc->next_queued_scb->hscb->tag); 7232 printk("Card NEXTQSCB = %d\n", ahc_inb(ahc, NEXT_QUEUED_SCB)); 7233 /* QINFIFO */ 7234 printk("QINFIFO entries: "); 7235 if ((ahc->features & AHC_QUEUE_REGS) != 0) { 7236 qinpos = ahc_inb(ahc, SNSCB_QOFF); 7237 ahc_outb(ahc, SNSCB_QOFF, qinpos); 7238 } else 7239 qinpos = ahc_inb(ahc, QINPOS); 7240 qintail = ahc->qinfifonext; 7241 while (qinpos != qintail) { 7242 printk("%d ", ahc->qinfifo[qinpos]); 7243 qinpos++; 7244 } 7245 printk("\n"); 7246 7247 printk("Waiting Queue entries: "); 7248 scb_index = ahc_inb(ahc, WAITING_SCBH); 7249 i = 0; 7250 while (scb_index != SCB_LIST_NULL && i++ < 256) { 7251 ahc_outb(ahc, SCBPTR, scb_index); 7252 printk("%d:%d ", scb_index, ahc_inb(ahc, SCB_TAG)); 7253 scb_index = ahc_inb(ahc, SCB_NEXT); 7254 } 7255 printk("\n"); 7256 7257 printk("Disconnected Queue entries: "); 7258 scb_index = ahc_inb(ahc, DISCONNECTED_SCBH); 7259 i = 0; 7260 while (scb_index != SCB_LIST_NULL && i++ < 256) { 7261 ahc_outb(ahc, SCBPTR, scb_index); 7262 printk("%d:%d ", scb_index, ahc_inb(ahc, SCB_TAG)); 7263 scb_index = ahc_inb(ahc, SCB_NEXT); 7264 } 7265 printk("\n"); 7266 7267 ahc_sync_qoutfifo(ahc, BUS_DMASYNC_POSTREAD); 7268 printk("QOUTFIFO entries: "); 7269 qoutpos = ahc->qoutfifonext; 7270 i = 0; 7271 while (ahc->qoutfifo[qoutpos] != SCB_LIST_NULL && i++ < 256) { 7272 printk("%d ", ahc->qoutfifo[qoutpos]); 7273 qoutpos++; 7274 } 7275 printk("\n"); 7276 7277 printk("Sequencer Free SCB List: "); 7278 scb_index = ahc_inb(ahc, FREE_SCBH); 7279 i = 0; 7280 while (scb_index != SCB_LIST_NULL && i++ < 256) { 7281 ahc_outb(ahc, SCBPTR, scb_index); 7282 printk("%d ", scb_index); 7283 scb_index = ahc_inb(ahc, SCB_NEXT); 7284 } 7285 printk("\n"); 7286 7287 printk("Sequencer SCB Info: "); 7288 for (i = 0; i < ahc->scb_data->maxhscbs; i++) { 7289 ahc_outb(ahc, SCBPTR, i); 7290 cur_col = printk("\n%3d ", i); 7291 7292 ahc_scb_control_print(ahc_inb(ahc, SCB_CONTROL), &cur_col, 60); 7293 ahc_scb_scsiid_print(ahc_inb(ahc, SCB_SCSIID), &cur_col, 60); 7294 ahc_scb_lun_print(ahc_inb(ahc, SCB_LUN), &cur_col, 60); 7295 ahc_scb_tag_print(ahc_inb(ahc, SCB_TAG), &cur_col, 60); 7296 } 7297 printk("\n"); 7298 7299 printk("Pending list: "); 7300 i = 0; 7301 LIST_FOREACH(scb, &ahc->pending_scbs, pending_links) { 7302 if (i++ > 256) 7303 break; 7304 cur_col = printk("\n%3d ", scb->hscb->tag); 7305 ahc_scb_control_print(scb->hscb->control, &cur_col, 60); 7306 ahc_scb_scsiid_print(scb->hscb->scsiid, &cur_col, 60); 7307 ahc_scb_lun_print(scb->hscb->lun, &cur_col, 60); 7308 if ((ahc->flags & AHC_PAGESCBS) == 0) { 7309 ahc_outb(ahc, SCBPTR, scb->hscb->tag); 7310 printk("("); 7311 ahc_scb_control_print(ahc_inb(ahc, SCB_CONTROL), 7312 &cur_col, 60); 7313 ahc_scb_tag_print(ahc_inb(ahc, SCB_TAG), &cur_col, 60); 7314 printk(")"); 7315 } 7316 } 7317 printk("\n"); 7318 7319 printk("Kernel Free SCB list: "); 7320 i = 0; 7321 SLIST_FOREACH(scb, &ahc->scb_data->free_scbs, links.sle) { 7322 if (i++ > 256) 7323 break; 7324 printk("%d ", scb->hscb->tag); 7325 } 7326 printk("\n"); 7327 7328 maxtarget = (ahc->features & (AHC_WIDE|AHC_TWIN)) ? 15 : 7; 7329 for (target = 0; target <= maxtarget; target++) { 7330 untagged_q = &ahc->untagged_queues[target]; 7331 if (TAILQ_FIRST(untagged_q) == NULL) 7332 continue; 7333 printk("Untagged Q(%d): ", target); 7334 i = 0; 7335 TAILQ_FOREACH(scb, untagged_q, links.tqe) { 7336 if (i++ > 256) 7337 break; 7338 printk("%d ", scb->hscb->tag); 7339 } 7340 printk("\n"); 7341 } 7342 7343 ahc_platform_dump_card_state(ahc); 7344 printk("\n<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>\n"); 7345 ahc_outb(ahc, SCBPTR, saved_scbptr); 7346 if (paused == 0) 7347 ahc_unpause(ahc); 7348} 7349 7350/************************* Target Mode ****************************************/ 7351#ifdef AHC_TARGET_MODE 7352cam_status 7353ahc_find_tmode_devs(struct ahc_softc *ahc, struct cam_sim *sim, union ccb *ccb, 7354 struct ahc_tmode_tstate **tstate, 7355 struct ahc_tmode_lstate **lstate, 7356 int notfound_failure) 7357{ 7358 7359 if ((ahc->features & AHC_TARGETMODE) == 0) 7360 return (CAM_REQ_INVALID); 7361 7362 /* 7363 * Handle the 'black hole' device that sucks up 7364 * requests to unattached luns on enabled targets. 7365 */ 7366 if (ccb->ccb_h.target_id == CAM_TARGET_WILDCARD 7367 && ccb->ccb_h.target_lun == CAM_LUN_WILDCARD) { 7368 *tstate = NULL; 7369 *lstate = ahc->black_hole; 7370 } else { 7371 u_int max_id; 7372 7373 max_id = (ahc->features & AHC_WIDE) ? 16 : 8; 7374 if (ccb->ccb_h.target_id >= max_id) 7375 return (CAM_TID_INVALID); 7376 7377 if (ccb->ccb_h.target_lun >= AHC_NUM_LUNS) 7378 return (CAM_LUN_INVALID); 7379 7380 *tstate = ahc->enabled_targets[ccb->ccb_h.target_id]; 7381 *lstate = NULL; 7382 if (*tstate != NULL) 7383 *lstate = 7384 (*tstate)->enabled_luns[ccb->ccb_h.target_lun]; 7385 } 7386 7387 if (notfound_failure != 0 && *lstate == NULL) 7388 return (CAM_PATH_INVALID); 7389 7390 return (CAM_REQ_CMP); 7391} 7392 7393void 7394ahc_handle_en_lun(struct ahc_softc *ahc, struct cam_sim *sim, union ccb *ccb) 7395{ 7396 struct ahc_tmode_tstate *tstate; 7397 struct ahc_tmode_lstate *lstate; 7398 struct ccb_en_lun *cel; 7399 cam_status status; 7400 u_long s; 7401 u_int target; 7402 u_int lun; 7403 u_int target_mask; 7404 u_int our_id; 7405 int error; 7406 char channel; 7407 7408 status = ahc_find_tmode_devs(ahc, sim, ccb, &tstate, &lstate, 7409 /*notfound_failure*/FALSE); 7410 7411 if (status != CAM_REQ_CMP) { 7412 ccb->ccb_h.status = status; 7413 return; 7414 } 7415 7416 if (cam_sim_bus(sim) == 0) 7417 our_id = ahc->our_id; 7418 else 7419 our_id = ahc->our_id_b; 7420 7421 if (ccb->ccb_h.target_id != our_id) { 7422 /* 7423 * our_id represents our initiator ID, or 7424 * the ID of the first target to have an 7425 * enabled lun in target mode. There are 7426 * two cases that may preclude enabling a 7427 * target id other than our_id. 7428 * 7429 * o our_id is for an active initiator role. 7430 * Since the hardware does not support 7431 * reselections to the initiator role at 7432 * anything other than our_id, and our_id 7433 * is used by the hardware to indicate the 7434 * ID to use for both select-out and 7435 * reselect-out operations, the only target 7436 * ID we can support in this mode is our_id. 7437 * 7438 * o The MULTARGID feature is not available and 7439 * a previous target mode ID has been enabled. 7440 */ 7441 if ((ahc->features & AHC_MULTIROLE) != 0) { 7442 7443 if ((ahc->features & AHC_MULTI_TID) != 0 7444 && (ahc->flags & AHC_INITIATORROLE) != 0) { 7445 /* 7446 * Only allow additional targets if 7447 * the initiator role is disabled. 7448 * The hardware cannot handle a re-select-in 7449 * on the initiator id during a re-select-out 7450 * on a different target id. 7451 */ 7452 status = CAM_TID_INVALID; 7453 } else if ((ahc->flags & AHC_INITIATORROLE) != 0 7454 || ahc->enabled_luns > 0) { 7455 /* 7456 * Only allow our target id to change 7457 * if the initiator role is not configured 7458 * and there are no enabled luns which 7459 * are attached to the currently registered 7460 * scsi id. 7461 */ 7462 status = CAM_TID_INVALID; 7463 } 7464 } else if ((ahc->features & AHC_MULTI_TID) == 0 7465 && ahc->enabled_luns > 0) { 7466 7467 status = CAM_TID_INVALID; 7468 } 7469 } 7470 7471 if (status != CAM_REQ_CMP) { 7472 ccb->ccb_h.status = status; 7473 return; 7474 } 7475 7476 /* 7477 * We now have an id that is valid. 7478 * If we aren't in target mode, switch modes. 7479 */ 7480 if ((ahc->flags & AHC_TARGETROLE) == 0 7481 && ccb->ccb_h.target_id != CAM_TARGET_WILDCARD) { 7482 u_long s; 7483 ahc_flag saved_flags; 7484 7485 printk("Configuring Target Mode\n"); 7486 ahc_lock(ahc, &s); 7487 if (LIST_FIRST(&ahc->pending_scbs) != NULL) { 7488 ccb->ccb_h.status = CAM_BUSY; 7489 ahc_unlock(ahc, &s); 7490 return; 7491 } 7492 saved_flags = ahc->flags; 7493 ahc->flags |= AHC_TARGETROLE; 7494 if ((ahc->features & AHC_MULTIROLE) == 0) 7495 ahc->flags &= ~AHC_INITIATORROLE; 7496 ahc_pause(ahc); 7497 error = ahc_loadseq(ahc); 7498 if (error != 0) { 7499 /* 7500 * Restore original configuration and notify 7501 * the caller that we cannot support target mode. 7502 * Since the adapter started out in this 7503 * configuration, the firmware load will succeed, 7504 * so there is no point in checking ahc_loadseq's 7505 * return value. 7506 */ 7507 ahc->flags = saved_flags; 7508 (void)ahc_loadseq(ahc); 7509 ahc_restart(ahc); 7510 ahc_unlock(ahc, &s); 7511 ccb->ccb_h.status = CAM_FUNC_NOTAVAIL; 7512 return; 7513 } 7514 ahc_restart(ahc); 7515 ahc_unlock(ahc, &s); 7516 } 7517 cel = &ccb->cel; 7518 target = ccb->ccb_h.target_id; 7519 lun = ccb->ccb_h.target_lun; 7520 channel = SIM_CHANNEL(ahc, sim); 7521 target_mask = 0x01 << target; 7522 if (channel == 'B') 7523 target_mask <<= 8; 7524 7525 if (cel->enable != 0) { 7526 u_int scsiseq; 7527 7528 /* Are we already enabled?? */ 7529 if (lstate != NULL) { 7530 xpt_print_path(ccb->ccb_h.path); 7531 printk("Lun already enabled\n"); 7532 ccb->ccb_h.status = CAM_LUN_ALRDY_ENA; 7533 return; 7534 } 7535 7536 if (cel->grp6_len != 0 7537 || cel->grp7_len != 0) { 7538 /* 7539 * Don't (yet?) support vendor 7540 * specific commands. 7541 */ 7542 ccb->ccb_h.status = CAM_REQ_INVALID; 7543 printk("Non-zero Group Codes\n"); 7544 return; 7545 } 7546 7547 /* 7548 * Seems to be okay. 7549 * Setup our data structures. 7550 */ 7551 if (target != CAM_TARGET_WILDCARD && tstate == NULL) { 7552 tstate = ahc_alloc_tstate(ahc, target, channel); 7553 if (tstate == NULL) { 7554 xpt_print_path(ccb->ccb_h.path); 7555 printk("Couldn't allocate tstate\n"); 7556 ccb->ccb_h.status = CAM_RESRC_UNAVAIL; 7557 return; 7558 } 7559 } 7560 lstate = kzalloc(sizeof(*lstate), GFP_ATOMIC); 7561 if (lstate == NULL) { 7562 xpt_print_path(ccb->ccb_h.path); 7563 printk("Couldn't allocate lstate\n"); 7564 ccb->ccb_h.status = CAM_RESRC_UNAVAIL; 7565 return; 7566 } 7567 status = xpt_create_path(&lstate->path, /*periph*/NULL, 7568 xpt_path_path_id(ccb->ccb_h.path), 7569 xpt_path_target_id(ccb->ccb_h.path), 7570 xpt_path_lun_id(ccb->ccb_h.path)); 7571 if (status != CAM_REQ_CMP) { 7572 kfree(lstate); 7573 xpt_print_path(ccb->ccb_h.path); 7574 printk("Couldn't allocate path\n"); 7575 ccb->ccb_h.status = CAM_RESRC_UNAVAIL; 7576 return; 7577 } 7578 SLIST_INIT(&lstate->accept_tios); 7579 SLIST_INIT(&lstate->immed_notifies); 7580 ahc_lock(ahc, &s); 7581 ahc_pause(ahc); 7582 if (target != CAM_TARGET_WILDCARD) { 7583 tstate->enabled_luns[lun] = lstate; 7584 ahc->enabled_luns++; 7585 7586 if ((ahc->features & AHC_MULTI_TID) != 0) { 7587 u_int targid_mask; 7588 7589 targid_mask = ahc_inb(ahc, TARGID) 7590 | (ahc_inb(ahc, TARGID + 1) << 8); 7591 7592 targid_mask |= target_mask; 7593 ahc_outb(ahc, TARGID, targid_mask); 7594 ahc_outb(ahc, TARGID+1, (targid_mask >> 8)); 7595 7596 ahc_update_scsiid(ahc, targid_mask); 7597 } else { 7598 u_int our_id; 7599 char channel; 7600 7601 channel = SIM_CHANNEL(ahc, sim); 7602 our_id = SIM_SCSI_ID(ahc, sim); 7603 7604 /* 7605 * This can only happen if selections 7606 * are not enabled 7607 */ 7608 if (target != our_id) { 7609 u_int sblkctl; 7610 char cur_channel; 7611 int swap; 7612 7613 sblkctl = ahc_inb(ahc, SBLKCTL); 7614 cur_channel = (sblkctl & SELBUSB) 7615 ? 'B' : 'A'; 7616 if ((ahc->features & AHC_TWIN) == 0) 7617 cur_channel = 'A'; 7618 swap = cur_channel != channel; 7619 if (channel == 'A') 7620 ahc->our_id = target; 7621 else 7622 ahc->our_id_b = target; 7623 7624 if (swap) 7625 ahc_outb(ahc, SBLKCTL, 7626 sblkctl ^ SELBUSB); 7627 7628 ahc_outb(ahc, SCSIID, target); 7629 7630 if (swap) 7631 ahc_outb(ahc, SBLKCTL, sblkctl); 7632 } 7633 } 7634 } else 7635 ahc->black_hole = lstate; 7636 /* Allow select-in operations */ 7637 if (ahc->black_hole != NULL && ahc->enabled_luns > 0) { 7638 scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); 7639 scsiseq |= ENSELI; 7640 ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq); 7641 scsiseq = ahc_inb(ahc, SCSISEQ); 7642 scsiseq |= ENSELI; 7643 ahc_outb(ahc, SCSISEQ, scsiseq); 7644 } 7645 ahc_unpause(ahc); 7646 ahc_unlock(ahc, &s); 7647 ccb->ccb_h.status = CAM_REQ_CMP; 7648 xpt_print_path(ccb->ccb_h.path); 7649 printk("Lun now enabled for target mode\n"); 7650 } else { 7651 struct scb *scb; 7652 int i, empty; 7653 7654 if (lstate == NULL) { 7655 ccb->ccb_h.status = CAM_LUN_INVALID; 7656 return; 7657 } 7658 7659 ahc_lock(ahc, &s); 7660 7661 ccb->ccb_h.status = CAM_REQ_CMP; 7662 LIST_FOREACH(scb, &ahc->pending_scbs, pending_links) { 7663 struct ccb_hdr *ccbh; 7664 7665 ccbh = &scb->io_ctx->ccb_h; 7666 if (ccbh->func_code == XPT_CONT_TARGET_IO 7667 && !xpt_path_comp(ccbh->path, ccb->ccb_h.path)){ 7668 printk("CTIO pending\n"); 7669 ccb->ccb_h.status = CAM_REQ_INVALID; 7670 ahc_unlock(ahc, &s); 7671 return; 7672 } 7673 } 7674 7675 if (SLIST_FIRST(&lstate->accept_tios) != NULL) { 7676 printk("ATIOs pending\n"); 7677 ccb->ccb_h.status = CAM_REQ_INVALID; 7678 } 7679 7680 if (SLIST_FIRST(&lstate->immed_notifies) != NULL) { 7681 printk("INOTs pending\n"); 7682 ccb->ccb_h.status = CAM_REQ_INVALID; 7683 } 7684 7685 if (ccb->ccb_h.status != CAM_REQ_CMP) { 7686 ahc_unlock(ahc, &s); 7687 return; 7688 } 7689 7690 xpt_print_path(ccb->ccb_h.path); 7691 printk("Target mode disabled\n"); 7692 xpt_free_path(lstate->path); 7693 kfree(lstate); 7694 7695 ahc_pause(ahc); 7696 /* Can we clean up the target too? */ 7697 if (target != CAM_TARGET_WILDCARD) { 7698 tstate->enabled_luns[lun] = NULL; 7699 ahc->enabled_luns--; 7700 for (empty = 1, i = 0; i < 8; i++) 7701 if (tstate->enabled_luns[i] != NULL) { 7702 empty = 0; 7703 break; 7704 } 7705 7706 if (empty) { 7707 ahc_free_tstate(ahc, target, channel, 7708 /*force*/FALSE); 7709 if (ahc->features & AHC_MULTI_TID) { 7710 u_int targid_mask; 7711 7712 targid_mask = ahc_inb(ahc, TARGID) 7713 | (ahc_inb(ahc, TARGID + 1) 7714 << 8); 7715 7716 targid_mask &= ~target_mask; 7717 ahc_outb(ahc, TARGID, targid_mask); 7718 ahc_outb(ahc, TARGID+1, 7719 (targid_mask >> 8)); 7720 ahc_update_scsiid(ahc, targid_mask); 7721 } 7722 } 7723 } else { 7724 7725 ahc->black_hole = NULL; 7726 7727 /* 7728 * We can't allow selections without 7729 * our black hole device. 7730 */ 7731 empty = TRUE; 7732 } 7733 if (ahc->enabled_luns == 0) { 7734 /* Disallow select-in */ 7735 u_int scsiseq; 7736 7737 scsiseq = ahc_inb(ahc, SCSISEQ_TEMPLATE); 7738 scsiseq &= ~ENSELI; 7739 ahc_outb(ahc, SCSISEQ_TEMPLATE, scsiseq); 7740 scsiseq = ahc_inb(ahc, SCSISEQ); 7741 scsiseq &= ~ENSELI; 7742 ahc_outb(ahc, SCSISEQ, scsiseq); 7743 7744 if ((ahc->features & AHC_MULTIROLE) == 0) { 7745 printk("Configuring Initiator Mode\n"); 7746 ahc->flags &= ~AHC_TARGETROLE; 7747 ahc->flags |= AHC_INITIATORROLE; 7748 /* 7749 * Returning to a configuration that 7750 * fit previously will always succeed. 7751 */ 7752 (void)ahc_loadseq(ahc); 7753 ahc_restart(ahc); 7754 /* 7755 * Unpaused. The extra unpause 7756 * that follows is harmless. 7757 */ 7758 } 7759 } 7760 ahc_unpause(ahc); 7761 ahc_unlock(ahc, &s); 7762 } 7763} 7764 7765static void 7766ahc_update_scsiid(struct ahc_softc *ahc, u_int targid_mask) 7767{ 7768 u_int scsiid_mask; 7769 u_int scsiid; 7770 7771 if ((ahc->features & AHC_MULTI_TID) == 0) 7772 panic("ahc_update_scsiid called on non-multitid unit\n"); 7773 7774 /* 7775 * Since we will rely on the TARGID mask 7776 * for selection enables, ensure that OID 7777 * in SCSIID is not set to some other ID 7778 * that we don't want to allow selections on. 7779 */ 7780 if ((ahc->features & AHC_ULTRA2) != 0) 7781 scsiid = ahc_inb(ahc, SCSIID_ULTRA2); 7782 else 7783 scsiid = ahc_inb(ahc, SCSIID); 7784 scsiid_mask = 0x1 << (scsiid & OID); 7785 if ((targid_mask & scsiid_mask) == 0) { 7786 u_int our_id; 7787 7788 /* ffs counts from 1 */ 7789 our_id = ffs(targid_mask); 7790 if (our_id == 0) 7791 our_id = ahc->our_id; 7792 else 7793 our_id--; 7794 scsiid &= TID; 7795 scsiid |= our_id; 7796 } 7797 if ((ahc->features & AHC_ULTRA2) != 0) 7798 ahc_outb(ahc, SCSIID_ULTRA2, scsiid); 7799 else 7800 ahc_outb(ahc, SCSIID, scsiid); 7801} 7802 7803static void 7804ahc_run_tqinfifo(struct ahc_softc *ahc, int paused) 7805{ 7806 struct target_cmd *cmd; 7807 7808 /* 7809 * If the card supports auto-access pause, 7810 * we can access the card directly regardless 7811 * of whether it is paused or not. 7812 */ 7813 if ((ahc->features & AHC_AUTOPAUSE) != 0) 7814 paused = TRUE; 7815 7816 ahc_sync_tqinfifo(ahc, BUS_DMASYNC_POSTREAD); 7817 while ((cmd = &ahc->targetcmds[ahc->tqinfifonext])->cmd_valid != 0) { 7818 7819 /* 7820 * Only advance through the queue if we 7821 * have the resources to process the command. 7822 */ 7823 if (ahc_handle_target_cmd(ahc, cmd) != 0) 7824 break; 7825 7826 cmd->cmd_valid = 0; 7827 ahc_dmamap_sync(ahc, ahc->shared_data_dmat, 7828 ahc->shared_data_dmamap, 7829 ahc_targetcmd_offset(ahc, ahc->tqinfifonext), 7830 sizeof(struct target_cmd), 7831 BUS_DMASYNC_PREREAD); 7832 ahc->tqinfifonext++; 7833 7834 /* 7835 * Lazily update our position in the target mode incoming 7836 * command queue as seen by the sequencer. 7837 */ 7838 if ((ahc->tqinfifonext & (HOST_TQINPOS - 1)) == 1) { 7839 if ((ahc->features & AHC_HS_MAILBOX) != 0) { 7840 u_int hs_mailbox; 7841 7842 hs_mailbox = ahc_inb(ahc, HS_MAILBOX); 7843 hs_mailbox &= ~HOST_TQINPOS; 7844 hs_mailbox |= ahc->tqinfifonext & HOST_TQINPOS; 7845 ahc_outb(ahc, HS_MAILBOX, hs_mailbox); 7846 } else { 7847 if (!paused) 7848 ahc_pause(ahc); 7849 ahc_outb(ahc, KERNEL_TQINPOS, 7850 ahc->tqinfifonext & HOST_TQINPOS); 7851 if (!paused) 7852 ahc_unpause(ahc); 7853 } 7854 } 7855 } 7856} 7857 7858static int 7859ahc_handle_target_cmd(struct ahc_softc *ahc, struct target_cmd *cmd) 7860{ 7861 struct ahc_tmode_tstate *tstate; 7862 struct ahc_tmode_lstate *lstate; 7863 struct ccb_accept_tio *atio; 7864 uint8_t *byte; 7865 int initiator; 7866 int target; 7867 int lun; 7868 7869 initiator = SCSIID_TARGET(ahc, cmd->scsiid); 7870 target = SCSIID_OUR_ID(cmd->scsiid); 7871 lun = (cmd->identify & MSG_IDENTIFY_LUNMASK); 7872 7873 byte = cmd->bytes; 7874 tstate = ahc->enabled_targets[target]; 7875 lstate = NULL; 7876 if (tstate != NULL) 7877 lstate = tstate->enabled_luns[lun]; 7878 7879 /* 7880 * Commands for disabled luns go to the black hole driver. 7881 */ 7882 if (lstate == NULL) 7883 lstate = ahc->black_hole; 7884 7885 atio = (struct ccb_accept_tio*)SLIST_FIRST(&lstate->accept_tios); 7886 if (atio == NULL) { 7887 ahc->flags |= AHC_TQINFIFO_BLOCKED; 7888 /* 7889 * Wait for more ATIOs from the peripheral driver for this lun. 7890 */ 7891 if (bootverbose) 7892 printk("%s: ATIOs exhausted\n", ahc_name(ahc)); 7893 return (1); 7894 } else 7895 ahc->flags &= ~AHC_TQINFIFO_BLOCKED; 7896#if 0 7897 printk("Incoming command from %d for %d:%d%s\n", 7898 initiator, target, lun, 7899 lstate == ahc->black_hole ? "(Black Holed)" : ""); 7900#endif 7901 SLIST_REMOVE_HEAD(&lstate->accept_tios, sim_links.sle); 7902 7903 if (lstate == ahc->black_hole) { 7904 /* Fill in the wildcards */ 7905 atio->ccb_h.target_id = target; 7906 atio->ccb_h.target_lun = lun; 7907 } 7908 7909 /* 7910 * Package it up and send it off to 7911 * whomever has this lun enabled. 7912 */ 7913 atio->sense_len = 0; 7914 atio->init_id = initiator; 7915 if (byte[0] != 0xFF) { 7916 /* Tag was included */ 7917 atio->tag_action = *byte++; 7918 atio->tag_id = *byte++; 7919 atio->ccb_h.flags = CAM_TAG_ACTION_VALID; 7920 } else { 7921 atio->ccb_h.flags = 0; 7922 } 7923 byte++; 7924 7925 /* Okay. Now determine the cdb size based on the command code */ 7926 switch (*byte >> CMD_GROUP_CODE_SHIFT) { 7927 case 0: 7928 atio->cdb_len = 6; 7929 break; 7930 case 1: 7931 case 2: 7932 atio->cdb_len = 10; 7933 break; 7934 case 4: 7935 atio->cdb_len = 16; 7936 break; 7937 case 5: 7938 atio->cdb_len = 12; 7939 break; 7940 case 3: 7941 default: 7942 /* Only copy the opcode. */ 7943 atio->cdb_len = 1; 7944 printk("Reserved or VU command code type encountered\n"); 7945 break; 7946 } 7947 7948 memcpy(atio->cdb_io.cdb_bytes, byte, atio->cdb_len); 7949 7950 atio->ccb_h.status |= CAM_CDB_RECVD; 7951 7952 if ((cmd->identify & MSG_IDENTIFY_DISCFLAG) == 0) { 7953 /* 7954 * We weren't allowed to disconnect. 7955 * We're hanging on the bus until a 7956 * continue target I/O comes in response 7957 * to this accept tio. 7958 */ 7959#if 0 7960 printk("Received Immediate Command %d:%d:%d - %p\n", 7961 initiator, target, lun, ahc->pending_device); 7962#endif 7963 ahc->pending_device = lstate; 7964 ahc_freeze_ccb((union ccb *)atio); 7965 atio->ccb_h.flags |= CAM_DIS_DISCONNECT; 7966 } 7967 xpt_done((union ccb*)atio); 7968 return (0); 7969} 7970 7971#endif 7972