1/****************************************************************************** 2 * 3 * Copyright(c) 2009-2012 Realtek Corporation. 4 * 5 * This program is free software; you can redistribute it and/or modify it 6 * under the terms of version 2 of the GNU General Public License as 7 * published by the Free Software Foundation. 8 * 9 * This program is distributed in the hope that it will be useful, but WITHOUT 10 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 11 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 12 * more details. 13 * 14 * The full GNU General Public License is included in this distribution in the 15 * file called LICENSE. 16 * 17 * Contact Information: 18 * wlanfae <wlanfae@realtek.com> 19 * Realtek Corporation, No. 2, Innovation Road II, Hsinchu Science Park, 20 * Hsinchu 300, Taiwan. 21 * 22 * Larry Finger <Larry.Finger@lwfinger.net> 23 * 24 *****************************************************************************/ 25 26#ifndef __RTL8723E_PWRSEQ_H__ 27#define __RTL8723E_PWRSEQ_H__ 28 29#include "../pwrseqcmd.h" 30/* 31 * Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd 32 * There are 6 HW Power States: 33 * 0: POFF--Power Off 34 * 1: PDN--Power Down 35 * 2: CARDEMU--Card Emulation 36 * 3: ACT--Active Mode 37 * 4: LPS--Low Power State 38 * 5: SUS--Suspend 39 * 40 * The transision from different states are defined below 41 * TRANS_CARDEMU_TO_ACT 42 * TRANS_ACT_TO_CARDEMU 43 * TRANS_CARDEMU_TO_SUS 44 * TRANS_SUS_TO_CARDEMU 45 * TRANS_CARDEMU_TO_PDN 46 * TRANS_ACT_TO_LPS 47 * TRANS_LPS_TO_ACT 48 * 49 * TRANS_END 50 */ 51 52#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS 10 53#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS 10 54#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS 10 55#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS 10 56#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS 10 57#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS 10 58#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15 59#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15 60#define RTL8723A_TRANS_END_STEPS 1 61 62/* format */ 63/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }*/ 64 65#define RTL8723A_TRANS_CARDEMU_TO_ACT \ 66 /* disable SW LPS 0x04[10]=0*/ \ 67 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 68 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},\ 69 /* wait till 0x04[17] = 1 power ready*/ \ 70 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 71 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},\ 72 /* release WLON reset 0x04[16]=1*/ \ 73 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 74 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\ 75 /* disable HWPDN 0x04[15]=0*/ \ 76 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 77 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\ 78 /* disable WL suspend*/ \ 79 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 80 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},\ 81 /* polling until return 0*/ \ 82 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 83 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\ 84 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 85 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, 86 87/* format */ 88/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 89 90#define RTL8723A_TRANS_ACT_TO_CARDEMU \ 91 /*0x1F[7:0] = 0 turn off RF*/ \ 92 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 93 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, \ 94 {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 95 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\ 96 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 97 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ 98 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 99 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, 100 101/* format */ 102/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/ 103#define RTL8723A_TRANS_CARDEMU_TO_SUS \ 104 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 105 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\ 106 PWR_BASEADDR_MAC, PWR_CMD_WRITE, \ 107 BIT(4)|BIT(3), (BIT(4)|BIT(3))},\ 108/*0x04[12:11] = 2b'01 enable WL suspend*/ \ 109 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK| \ 110 PWR_INTF_SDIO_MSK,\ 111 PWR_BASEADDR_MAC, \ 112 PWR_CMD_WRITE, \ 113 BIT(3)|BIT(4), BIT(3)}, \ 114/*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 115 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 116 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, \ 117 PWR_CMD_WRITE, BIT(3)|BIT(4), \ 118 BIT(3)|BIT(4)}, \ 119/*Set SDIO suspend local register*/ \ 120 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 121 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 122 PWR_CMD_WRITE, BIT(0), BIT(0)}, \ 123/*wait power state to suspend*/ \ 124 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 125 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 126 PWR_CMD_POLLING, BIT(1), 0}, 127 128/* format */ 129/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 130 131#define RTL8723A_TRANS_SUS_TO_CARDEMU \ 132 /*Set SDIO suspend local register*/ \ 133 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 134 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0},\ 135 /*wait power state to suspend*/ \ 136 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\ 137 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)},\ 138 /*0x04[12:11] = 2b'01enable WL suspend*/ \ 139 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 140 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, 141 142/* format */ 143/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 144 145#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \ 146 /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 147 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 148 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ 149 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \ 150/*0x04[10] = 1, enable SW LPS*/ \ 151 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 152 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\ 153 PWR_CMD_WRITE, BIT(2), BIT(2)}, \ 154/*Set SDIO suspend local register*/ \ 155 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 156 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 157 PWR_CMD_WRITE, BIT(0), BIT(0)}, \ 158 /*wait power state to suspend*/ \ 159 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 160 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 161 PWR_CMD_POLLING, BIT(1), 0}, 162 163/* format */ 164/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 165 166#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU\ 167/*Set SDIO suspend local register*/ \ 168 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 169 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 170 PWR_CMD_WRITE, BIT(0), 0}, \ 171 /*wait power state to suspend*/ \ 172 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 173 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 174 PWR_CMD_POLLING, BIT(1), BIT(1)},\ 175 /*0x04[12:11] = 2b'00enable WL suspend*/ \ 176 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 177 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 178 PWR_CMD_WRITE, BIT(3)|BIT(4), 0},\ 179/*PCIe DMA start*/ \ 180 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 181 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 182 PWR_CMD_WRITE, 0xFF, 0}, 183 184/* format */ 185/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 186#define RTL8723A_TRANS_CARDEMU_TO_PDN \ 187 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 188 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 189 PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\ 190 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 191 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 192 PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/ 193 194/* format */ 195/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 196#define RTL8723A_TRANS_PDN_TO_CARDEMU \ 197 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 198 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 199 PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/ 200 201/* format */ 202/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 203 204#define RTL8723A_TRANS_ACT_TO_LPS \ 205 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 206 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 207 PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ 208 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 209 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 210 PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \ 211 /*Should be zero if no packet is transmitting*/ \ 212 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 213 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 214 PWR_CMD_POLLING, 0xFF, 0},\ 215 /*Should be zero if no packet is transmitting*/ \ 216 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 217 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 218 PWR_CMD_POLLING, 0xFF, 0},\ 219 /*Should be zero if no packet is transmitting*/ \ 220 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 221 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 222 PWR_CMD_POLLING, 0xFF, 0},\ 223 /*Should be zero if no packet is transmitting*/ \ 224 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 225 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 226 PWR_CMD_POLLING, 0xFF, 0},\ 227 /*CCK and OFDM are disabled,and clock are gated*/ \ 228 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 229 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 230 PWR_CMD_WRITE, BIT(0), 0},\ 231 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 232 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 233 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/\ 234 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 235 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 236 PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \ 237 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 238 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 239 PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ 240 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 241 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 242 PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \ 243 /*Respond TxOK to scheduler*/ \ 244 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 245 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 246 PWR_CMD_WRITE, BIT(5), BIT(5)},\ 247 248#define RTL8723A_TRANS_LPS_TO_ACT\ 249/* format */ \ 250/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ \ 251 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 252 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\ 253 PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ 254 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 255 PWR_INTF_USB_MSK, PWR_BASEADDR_MAC,\ 256 PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ 257 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 258 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\ 259 PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ 260 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 261 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 262 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 263 /*. 0x08[4] = 0 switch TSF to 40M*/\ 264 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 265 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 266 PWR_CMD_WRITE, BIT(4), 0}, \ 267 /*Polling 0x109[7]=0 TSF in 40M*/\ 268 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 269 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 270 PWR_CMD_POLLING, BIT(7), 0}, \ 271 /*. 0x29[7:6] = 2b'00 enable BB clock*/\ 272 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 273 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 274 PWR_CMD_WRITE, BIT(6)|BIT(7), 0},\ 275 /*. 0x101[1] = 1*/\ 276 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 277 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 278 PWR_CMD_WRITE, BIT(1), BIT(1)},\ 279 /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 280 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 281 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 282 PWR_CMD_WRITE, 0xFF, 0xFF},\ 283 /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 284 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 285 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 286 PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)},\ 287 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ 288 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\ 289 PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 290 291/* format */ 292/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ 293 294#define RTL8723A_TRANS_END \ 295 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ 296 0, PWR_CMD_END, 0, 0} 297 298extern struct wlan_pwr_cfg rtl8723A_power_on_flow 299 [RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS + 300 RTL8723A_TRANS_END_STEPS]; 301extern struct wlan_pwr_cfg rtl8723A_radio_off_flow 302 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 303 RTL8723A_TRANS_END_STEPS]; 304extern struct wlan_pwr_cfg rtl8723A_card_disable_flow 305 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 306 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 307 RTL8723A_TRANS_END_STEPS]; 308extern struct wlan_pwr_cfg rtl8723A_card_enable_flow 309 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 310 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 311 RTL8723A_TRANS_END_STEPS]; 312extern struct wlan_pwr_cfg rtl8723A_suspend_flow 313 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 314 RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS + 315 RTL8723A_TRANS_END_STEPS]; 316extern struct wlan_pwr_cfg rtl8723A_resume_flow 317 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 318 RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS + 319 RTL8723A_TRANS_END_STEPS]; 320extern struct wlan_pwr_cfg rtl8723A_hwpdn_flow 321 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS + 322 RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS + 323 RTL8723A_TRANS_END_STEPS]; 324extern struct wlan_pwr_cfg rtl8723A_enter_lps_flow 325 [RTL8723A_TRANS_ACT_TO_LPS_STEPS + RTL8723A_TRANS_END_STEPS]; 326extern struct wlan_pwr_cfg rtl8723A_leave_lps_flow 327 [RTL8723A_TRANS_LPS_TO_ACT_STEPS + RTL8723A_TRANS_END_STEPS]; 328 329/* RTL8723 Power Configuration CMDs for PCIe interface */ 330#define Rtl8723_NIC_PWR_ON_FLOW rtl8723A_power_on_flow 331#define Rtl8723_NIC_RF_OFF_FLOW rtl8723A_radio_off_flow 332#define Rtl8723_NIC_DISABLE_FLOW rtl8723A_card_disable_flow 333#define Rtl8723_NIC_ENABLE_FLOW rtl8723A_card_enable_flow 334#define Rtl8723_NIC_SUSPEND_FLOW rtl8723A_suspend_flow 335#define Rtl8723_NIC_RESUME_FLOW rtl8723A_resume_flow 336#define Rtl8723_NIC_PDN_FLOW rtl8723A_hwpdn_flow 337#define Rtl8723_NIC_LPS_ENTER_FLOW rtl8723A_enter_lps_flow 338#define Rtl8723_NIC_LPS_LEAVE_FLOW rtl8723A_leave_lps_flow 339 340#endif 341