1/*
2 *	Comtrol SV11 card driver
3 *
4 *	This is a slightly odd Z85230 synchronous driver. All you need to
5 *	know basically is
6 *
7 *	Its a genuine Z85230
8 *
9 *	It supports DMA using two DMA channels in SYNC mode. The driver doesn't
10 *	use these facilities
11 *
12 *	The control port is at io+1, the data at io+3 and turning off the DMA
13 *	is done by writing 0 to io+4
14 *
15 *	The hardware does the bus handling to avoid the need for delays between
16 *	touching control registers.
17 *
18 *	Port B isn't wired (why - beats me)
19 *
20 *	Generic HDLC port Copyright (C) 2008 Krzysztof Halasa <khc@pm.waw.pl>
21 */
22
23#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
24
25#include <linux/module.h>
26#include <linux/kernel.h>
27#include <linux/mm.h>
28#include <linux/net.h>
29#include <linux/skbuff.h>
30#include <linux/netdevice.h>
31#include <linux/if_arp.h>
32#include <linux/delay.h>
33#include <linux/hdlc.h>
34#include <linux/ioport.h>
35#include <linux/slab.h>
36#include <net/arp.h>
37
38#include <asm/irq.h>
39#include <asm/io.h>
40#include <asm/dma.h>
41#include <asm/byteorder.h>
42#include "z85230.h"
43
44static int dma;
45
46/*
47 *	Network driver support routines
48 */
49
50static inline struct z8530_dev* dev_to_sv(struct net_device *dev)
51{
52	return (struct z8530_dev *)dev_to_hdlc(dev)->priv;
53}
54
55/*
56 *	Frame receive. Simple for our card as we do HDLC and there
57 *	is no funny garbage involved
58 */
59
60static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
61{
62	/* Drop the CRC - it's not a good idea to try and negotiate it ;) */
63	skb_trim(skb, skb->len - 2);
64	skb->protocol = hdlc_type_trans(skb, c->netdevice);
65	skb_reset_mac_header(skb);
66	skb->dev = c->netdevice;
67	/*
68	 *	Send it to the PPP layer. We don't have time to process
69	 *	it right now.
70	 */
71	netif_rx(skb);
72}
73
74/*
75 *	We've been placed in the UP state
76 */
77
78static int hostess_open(struct net_device *d)
79{
80	struct z8530_dev *sv11 = dev_to_sv(d);
81	int err = -1;
82
83	/*
84	 *	Link layer up
85	 */
86	switch (dma) {
87		case 0:
88			err = z8530_sync_open(d, &sv11->chanA);
89			break;
90		case 1:
91			err = z8530_sync_dma_open(d, &sv11->chanA);
92			break;
93		case 2:
94			err = z8530_sync_txdma_open(d, &sv11->chanA);
95			break;
96	}
97
98	if (err)
99		return err;
100
101	err = hdlc_open(d);
102	if (err) {
103		switch (dma) {
104			case 0:
105				z8530_sync_close(d, &sv11->chanA);
106				break;
107			case 1:
108				z8530_sync_dma_close(d, &sv11->chanA);
109				break;
110			case 2:
111				z8530_sync_txdma_close(d, &sv11->chanA);
112				break;
113		}
114		return err;
115	}
116	sv11->chanA.rx_function = hostess_input;
117
118	/*
119	 *	Go go go
120	 */
121
122	netif_start_queue(d);
123	return 0;
124}
125
126static int hostess_close(struct net_device *d)
127{
128	struct z8530_dev *sv11 = dev_to_sv(d);
129	/*
130	 *	Discard new frames
131	 */
132	sv11->chanA.rx_function = z8530_null_rx;
133
134	hdlc_close(d);
135	netif_stop_queue(d);
136
137	switch (dma) {
138		case 0:
139			z8530_sync_close(d, &sv11->chanA);
140			break;
141		case 1:
142			z8530_sync_dma_close(d, &sv11->chanA);
143			break;
144		case 2:
145			z8530_sync_txdma_close(d, &sv11->chanA);
146			break;
147	}
148	return 0;
149}
150
151static int hostess_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
152{
153	/* struct z8530_dev *sv11=dev_to_sv(d);
154	   z8530_ioctl(d,&sv11->chanA,ifr,cmd) */
155	return hdlc_ioctl(d, ifr, cmd);
156}
157
158/*
159 *	Passed network frames, fire them downwind.
160 */
161
162static netdev_tx_t hostess_queue_xmit(struct sk_buff *skb,
163					    struct net_device *d)
164{
165	return z8530_queue_xmit(&dev_to_sv(d)->chanA, skb);
166}
167
168static int hostess_attach(struct net_device *dev, unsigned short encoding,
169			  unsigned short parity)
170{
171	if (encoding == ENCODING_NRZ && parity == PARITY_CRC16_PR1_CCITT)
172		return 0;
173	return -EINVAL;
174}
175
176/*
177 *	Description block for a Comtrol Hostess SV11 card
178 */
179
180static const struct net_device_ops hostess_ops = {
181	.ndo_open       = hostess_open,
182	.ndo_stop       = hostess_close,
183	.ndo_change_mtu = hdlc_change_mtu,
184	.ndo_start_xmit = hdlc_start_xmit,
185	.ndo_do_ioctl   = hostess_ioctl,
186};
187
188static struct z8530_dev *sv11_init(int iobase, int irq)
189{
190	struct z8530_dev *sv;
191	struct net_device *netdev;
192	/*
193	 *	Get the needed I/O space
194	 */
195
196	if (!request_region(iobase, 8, "Comtrol SV11")) {
197		pr_warn("I/O 0x%X already in use\n", iobase);
198		return NULL;
199	}
200
201	sv = kzalloc(sizeof(struct z8530_dev), GFP_KERNEL);
202	if (!sv)
203		goto err_kzalloc;
204
205	/*
206	 *	Stuff in the I/O addressing
207	 */
208
209	sv->active = 0;
210
211	sv->chanA.ctrlio = iobase + 1;
212	sv->chanA.dataio = iobase + 3;
213	sv->chanB.ctrlio = -1;
214	sv->chanB.dataio = -1;
215	sv->chanA.irqs = &z8530_nop;
216	sv->chanB.irqs = &z8530_nop;
217
218	outb(0, iobase + 4);		/* DMA off */
219
220	/* We want a fast IRQ for this device. Actually we'd like an even faster
221	   IRQ ;) - This is one driver RtLinux is made for */
222
223	if (request_irq(irq, z8530_interrupt, 0,
224			"Hostess SV11", sv) < 0) {
225		pr_warn("IRQ %d already in use\n", irq);
226		goto err_irq;
227	}
228
229	sv->irq = irq;
230	sv->chanA.private = sv;
231	sv->chanA.dev = sv;
232	sv->chanB.dev = sv;
233
234	if (dma) {
235		/*
236		 *	You can have DMA off or 1 and 3 thats the lot
237		 *	on the Comtrol.
238		 */
239		sv->chanA.txdma = 3;
240		sv->chanA.rxdma = 1;
241		outb(0x03 | 0x08, iobase + 4);		/* DMA on */
242		if (request_dma(sv->chanA.txdma, "Hostess SV/11 (TX)"))
243			goto err_txdma;
244
245		if (dma == 1)
246			if (request_dma(sv->chanA.rxdma, "Hostess SV/11 (RX)"))
247				goto err_rxdma;
248	}
249
250	/* Kill our private IRQ line the hostess can end up chattering
251	   until the configuration is set */
252	disable_irq(irq);
253
254	/*
255	 *	Begin normal initialise
256	 */
257
258	if (z8530_init(sv)) {
259		pr_err("Z8530 series device not found\n");
260		enable_irq(irq);
261		goto free_dma;
262	}
263	z8530_channel_load(&sv->chanB, z8530_dead_port);
264	if (sv->type == Z85C30)
265		z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream);
266	else
267		z8530_channel_load(&sv->chanA, z8530_hdlc_kilostream_85230);
268
269	enable_irq(irq);
270
271	/*
272	 *	Now we can take the IRQ
273	 */
274
275	sv->chanA.netdevice = netdev = alloc_hdlcdev(sv);
276	if (!netdev)
277		goto free_dma;
278
279	dev_to_hdlc(netdev)->attach = hostess_attach;
280	dev_to_hdlc(netdev)->xmit = hostess_queue_xmit;
281	netdev->netdev_ops = &hostess_ops;
282	netdev->base_addr = iobase;
283	netdev->irq = irq;
284
285	if (register_hdlc_device(netdev)) {
286		pr_err("unable to register HDLC device\n");
287		free_netdev(netdev);
288		goto free_dma;
289	}
290
291	z8530_describe(sv, "I/O", iobase);
292	sv->active = 1;
293	return sv;
294
295free_dma:
296	if (dma == 1)
297		free_dma(sv->chanA.rxdma);
298err_rxdma:
299	if (dma)
300		free_dma(sv->chanA.txdma);
301err_txdma:
302	free_irq(irq, sv);
303err_irq:
304	kfree(sv);
305err_kzalloc:
306	release_region(iobase, 8);
307	return NULL;
308}
309
310static void sv11_shutdown(struct z8530_dev *dev)
311{
312	unregister_hdlc_device(dev->chanA.netdevice);
313	z8530_shutdown(dev);
314	free_irq(dev->irq, dev);
315	if (dma) {
316		if (dma == 1)
317			free_dma(dev->chanA.rxdma);
318		free_dma(dev->chanA.txdma);
319	}
320	release_region(dev->chanA.ctrlio - 1, 8);
321	free_netdev(dev->chanA.netdevice);
322	kfree(dev);
323}
324
325static int io = 0x200;
326static int irq = 9;
327
328module_param(io, int, 0);
329MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
330module_param(dma, int, 0);
331MODULE_PARM_DESC(dma, "Set this to 1 to use DMA1/DMA3 for TX/RX");
332module_param(irq, int, 0);
333MODULE_PARM_DESC(irq, "The interrupt line setting for the Comtrol Hostess SV11 card");
334
335MODULE_AUTHOR("Alan Cox");
336MODULE_LICENSE("GPL");
337MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
338
339static struct z8530_dev *sv11_unit;
340
341int init_module(void)
342{
343	if ((sv11_unit = sv11_init(io, irq)) == NULL)
344		return -ENODEV;
345	return 0;
346}
347
348void cleanup_module(void)
349{
350	if (sv11_unit)
351		sv11_shutdown(sv11_unit);
352}
353