1/* Copyright 2008-2013 Broadcom Corporation 2 * 3 * Unless you and Broadcom execute a separate written software license 4 * agreement governing use of this software, this software is licensed to you 5 * under the terms of the GNU General Public License version 2, available 6 * at http://www.gnu.org/licenses/old-licenses/gpl-2.0.html (the "GPL"). 7 * 8 * Notwithstanding the above, under no circumstances may you combine this 9 * software in any way with any other Broadcom software provided under a 10 * license other than the GPL, without Broadcom's express prior written 11 * consent. 12 * 13 * Written by Yaniv Rosner 14 * 15 */ 16 17#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 18 19#include <linux/kernel.h> 20#include <linux/errno.h> 21#include <linux/pci.h> 22#include <linux/netdevice.h> 23#include <linux/delay.h> 24#include <linux/ethtool.h> 25#include <linux/mutex.h> 26 27#include "bnx2x.h" 28#include "bnx2x_cmn.h" 29 30typedef int (*read_sfp_module_eeprom_func_p)(struct bnx2x_phy *phy, 31 struct link_params *params, 32 u8 dev_addr, u16 addr, u8 byte_cnt, 33 u8 *o_buf, u8); 34/********************************************************/ 35#define ETH_HLEN 14 36/* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */ 37#define ETH_OVREHEAD (ETH_HLEN + 8 + 8) 38#define ETH_MIN_PACKET_SIZE 60 39#define ETH_MAX_PACKET_SIZE 1500 40#define ETH_MAX_JUMBO_PACKET_SIZE 9600 41#define MDIO_ACCESS_TIMEOUT 1000 42#define WC_LANE_MAX 4 43#define I2C_SWITCH_WIDTH 2 44#define I2C_BSC0 0 45#define I2C_BSC1 1 46#define I2C_WA_RETRY_CNT 3 47#define I2C_WA_PWR_ITER (I2C_WA_RETRY_CNT - 1) 48#define MCPR_IMC_COMMAND_READ_OP 1 49#define MCPR_IMC_COMMAND_WRITE_OP 2 50 51/* LED Blink rate that will achieve ~15.9Hz */ 52#define LED_BLINK_RATE_VAL_E3 354 53#define LED_BLINK_RATE_VAL_E1X_E2 480 54/***********************************************************/ 55/* Shortcut definitions */ 56/***********************************************************/ 57 58#define NIG_LATCH_BC_ENABLE_MI_INT 0 59 60#define NIG_STATUS_EMAC0_MI_INT \ 61 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT 62#define NIG_STATUS_XGXS0_LINK10G \ 63 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G 64#define NIG_STATUS_XGXS0_LINK_STATUS \ 65 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS 66#define NIG_STATUS_XGXS0_LINK_STATUS_SIZE \ 67 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE 68#define NIG_STATUS_SERDES0_LINK_STATUS \ 69 NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS 70#define NIG_MASK_MI_INT \ 71 NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT 72#define NIG_MASK_XGXS0_LINK10G \ 73 NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G 74#define NIG_MASK_XGXS0_LINK_STATUS \ 75 NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS 76#define NIG_MASK_SERDES0_LINK_STATUS \ 77 NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS 78 79#define MDIO_AN_CL73_OR_37_COMPLETE \ 80 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | \ 81 MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE) 82 83#define XGXS_RESET_BITS \ 84 (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW | \ 85 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ | \ 86 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN | \ 87 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD | \ 88 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB) 89 90#define SERDES_RESET_BITS \ 91 (MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW | \ 92 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ | \ 93 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN | \ 94 MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD) 95 96#define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37 97#define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73 98#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM 99#define AUTONEG_PARALLEL \ 100 SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION 101#define AUTONEG_SGMII_FIBER_AUTODET \ 102 SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT 103#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY 104 105#define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \ 106 MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 107#define GP_STATUS_PAUSE_RSOLUTION_RXSIDE \ 108 MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 109#define GP_STATUS_SPEED_MASK \ 110 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 111#define GP_STATUS_10M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 112#define GP_STATUS_100M MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 113#define GP_STATUS_1G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 114#define GP_STATUS_2_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 115#define GP_STATUS_5G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 116#define GP_STATUS_6G MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 117#define GP_STATUS_10G_HIG \ 118 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 119#define GP_STATUS_10G_CX4 \ 120 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 121#define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 122#define GP_STATUS_10G_KX4 \ 123 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 124#define GP_STATUS_10G_KR MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR 125#define GP_STATUS_10G_XFI MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI 126#define GP_STATUS_20G_DXGXS MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS 127#define GP_STATUS_10G_SFI MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI 128#define GP_STATUS_20G_KR2 MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_KR2 129#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD 130#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD 131#define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD 132#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4 133#define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD 134#define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD 135#define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD 136#define LINK_1000XFD LINK_STATUS_SPEED_AND_DUPLEX_1000XFD 137#define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD 138#define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD 139#define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD 140#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD 141#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD 142#define LINK_20GTFD LINK_STATUS_SPEED_AND_DUPLEX_20GTFD 143#define LINK_20GXFD LINK_STATUS_SPEED_AND_DUPLEX_20GXFD 144 145#define LINK_UPDATE_MASK \ 146 (LINK_STATUS_SPEED_AND_DUPLEX_MASK | \ 147 LINK_STATUS_LINK_UP | \ 148 LINK_STATUS_PHYSICAL_LINK_FLAG | \ 149 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE | \ 150 LINK_STATUS_RX_FLOW_CONTROL_FLAG_MASK | \ 151 LINK_STATUS_TX_FLOW_CONTROL_FLAG_MASK | \ 152 LINK_STATUS_PARALLEL_DETECTION_FLAG_MASK | \ 153 LINK_STATUS_LINK_PARTNER_SYMMETRIC_PAUSE | \ 154 LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE) 155 156#define SFP_EEPROM_CON_TYPE_ADDR 0x2 157 #define SFP_EEPROM_CON_TYPE_VAL_UNKNOWN 0x0 158 #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 159 #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21 160 #define SFP_EEPROM_CON_TYPE_VAL_RJ45 0x22 161 162 163#define SFP_EEPROM_10G_COMP_CODE_ADDR 0x3 164 #define SFP_EEPROM_10G_COMP_CODE_SR_MASK (1<<4) 165 #define SFP_EEPROM_10G_COMP_CODE_LR_MASK (1<<5) 166 #define SFP_EEPROM_10G_COMP_CODE_LRM_MASK (1<<6) 167 168#define SFP_EEPROM_1G_COMP_CODE_ADDR 0x6 169 #define SFP_EEPROM_1G_COMP_CODE_SX (1<<0) 170 #define SFP_EEPROM_1G_COMP_CODE_LX (1<<1) 171 #define SFP_EEPROM_1G_COMP_CODE_CX (1<<2) 172 #define SFP_EEPROM_1G_COMP_CODE_BASE_T (1<<3) 173 174#define SFP_EEPROM_FC_TX_TECH_ADDR 0x8 175 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4 176 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8 177 178#define SFP_EEPROM_OPTIONS_ADDR 0x40 179 #define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1 180#define SFP_EEPROM_OPTIONS_SIZE 2 181 182#define EDC_MODE_LINEAR 0x0022 183#define EDC_MODE_LIMITING 0x0044 184#define EDC_MODE_PASSIVE_DAC 0x0055 185#define EDC_MODE_ACTIVE_DAC 0x0066 186 187/* ETS defines*/ 188#define DCBX_INVALID_COS (0xFF) 189 190#define ETS_BW_LIMIT_CREDIT_UPPER_BOUND (0x5000) 191#define ETS_BW_LIMIT_CREDIT_WEIGHT (0x5000) 192#define ETS_E3B0_NIG_MIN_W_VAL_UP_TO_10GBPS (1360) 193#define ETS_E3B0_NIG_MIN_W_VAL_20GBPS (2720) 194#define ETS_E3B0_PBF_MIN_W_VAL (10000) 195 196#define MAX_PACKET_SIZE (9700) 197#define MAX_KR_LINK_RETRY 4 198#define DEFAULT_TX_DRV_BRDCT 2 199#define DEFAULT_TX_DRV_IFIR 0 200#define DEFAULT_TX_DRV_POST2 3 201#define DEFAULT_TX_DRV_IPRE_DRIVER 6 202 203/**********************************************************/ 204/* INTERFACE */ 205/**********************************************************/ 206 207#define CL22_WR_OVER_CL45(_bp, _phy, _bank, _addr, _val) \ 208 bnx2x_cl45_write(_bp, _phy, \ 209 (_phy)->def_md_devad, \ 210 (_bank + (_addr & 0xf)), \ 211 _val) 212 213#define CL22_RD_OVER_CL45(_bp, _phy, _bank, _addr, _val) \ 214 bnx2x_cl45_read(_bp, _phy, \ 215 (_phy)->def_md_devad, \ 216 (_bank + (_addr & 0xf)), \ 217 _val) 218 219static int bnx2x_check_half_open_conn(struct link_params *params, 220 struct link_vars *vars, u8 notify); 221static int bnx2x_sfp_module_detection(struct bnx2x_phy *phy, 222 struct link_params *params); 223 224static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits) 225{ 226 u32 val = REG_RD(bp, reg); 227 228 val |= bits; 229 REG_WR(bp, reg, val); 230 return val; 231} 232 233static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits) 234{ 235 u32 val = REG_RD(bp, reg); 236 237 val &= ~bits; 238 REG_WR(bp, reg, val); 239 return val; 240} 241 242/* 243 * bnx2x_check_lfa - This function checks if link reinitialization is required, 244 * or link flap can be avoided. 245 * 246 * @params: link parameters 247 * Returns 0 if Link Flap Avoidance conditions are met otherwise, the failed 248 * condition code. 249 */ 250static int bnx2x_check_lfa(struct link_params *params) 251{ 252 u32 link_status, cfg_idx, lfa_mask, cfg_size; 253 u32 cur_speed_cap_mask, cur_req_fc_auto_adv, additional_config; 254 u32 saved_val, req_val, eee_status; 255 struct bnx2x *bp = params->bp; 256 257 additional_config = 258 REG_RD(bp, params->lfa_base + 259 offsetof(struct shmem_lfa, additional_config)); 260 261 /* NOTE: must be first condition checked - 262 * to verify DCC bit is cleared in any case! 263 */ 264 if (additional_config & NO_LFA_DUE_TO_DCC_MASK) { 265 DP(NETIF_MSG_LINK, "No LFA due to DCC flap after clp exit\n"); 266 REG_WR(bp, params->lfa_base + 267 offsetof(struct shmem_lfa, additional_config), 268 additional_config & ~NO_LFA_DUE_TO_DCC_MASK); 269 return LFA_DCC_LFA_DISABLED; 270 } 271 272 /* Verify that link is up */ 273 link_status = REG_RD(bp, params->shmem_base + 274 offsetof(struct shmem_region, 275 port_mb[params->port].link_status)); 276 if (!(link_status & LINK_STATUS_LINK_UP)) 277 return LFA_LINK_DOWN; 278 279 /* if loaded after BOOT from SAN, don't flap the link in any case and 280 * rely on link set by preboot driver 281 */ 282 if (params->feature_config_flags & FEATURE_CONFIG_BOOT_FROM_SAN) 283 return 0; 284 285 /* Verify that loopback mode is not set */ 286 if (params->loopback_mode) 287 return LFA_LOOPBACK_ENABLED; 288 289 /* Verify that MFW supports LFA */ 290 if (!params->lfa_base) 291 return LFA_MFW_IS_TOO_OLD; 292 293 if (params->num_phys == 3) { 294 cfg_size = 2; 295 lfa_mask = 0xffffffff; 296 } else { 297 cfg_size = 1; 298 lfa_mask = 0xffff; 299 } 300 301 /* Compare Duplex */ 302 saved_val = REG_RD(bp, params->lfa_base + 303 offsetof(struct shmem_lfa, req_duplex)); 304 req_val = params->req_duplex[0] | (params->req_duplex[1] << 16); 305 if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { 306 DP(NETIF_MSG_LINK, "Duplex mismatch %x vs. %x\n", 307 (saved_val & lfa_mask), (req_val & lfa_mask)); 308 return LFA_DUPLEX_MISMATCH; 309 } 310 /* Compare Flow Control */ 311 saved_val = REG_RD(bp, params->lfa_base + 312 offsetof(struct shmem_lfa, req_flow_ctrl)); 313 req_val = params->req_flow_ctrl[0] | (params->req_flow_ctrl[1] << 16); 314 if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { 315 DP(NETIF_MSG_LINK, "Flow control mismatch %x vs. %x\n", 316 (saved_val & lfa_mask), (req_val & lfa_mask)); 317 return LFA_FLOW_CTRL_MISMATCH; 318 } 319 /* Compare Link Speed */ 320 saved_val = REG_RD(bp, params->lfa_base + 321 offsetof(struct shmem_lfa, req_line_speed)); 322 req_val = params->req_line_speed[0] | (params->req_line_speed[1] << 16); 323 if ((saved_val & lfa_mask) != (req_val & lfa_mask)) { 324 DP(NETIF_MSG_LINK, "Link speed mismatch %x vs. %x\n", 325 (saved_val & lfa_mask), (req_val & lfa_mask)); 326 return LFA_LINK_SPEED_MISMATCH; 327 } 328 329 for (cfg_idx = 0; cfg_idx < cfg_size; cfg_idx++) { 330 cur_speed_cap_mask = REG_RD(bp, params->lfa_base + 331 offsetof(struct shmem_lfa, 332 speed_cap_mask[cfg_idx])); 333 334 if (cur_speed_cap_mask != params->speed_cap_mask[cfg_idx]) { 335 DP(NETIF_MSG_LINK, "Speed Cap mismatch %x vs. %x\n", 336 cur_speed_cap_mask, 337 params->speed_cap_mask[cfg_idx]); 338 return LFA_SPEED_CAP_MISMATCH; 339 } 340 } 341 342 cur_req_fc_auto_adv = 343 REG_RD(bp, params->lfa_base + 344 offsetof(struct shmem_lfa, additional_config)) & 345 REQ_FC_AUTO_ADV_MASK; 346 347 if ((u16)cur_req_fc_auto_adv != params->req_fc_auto_adv) { 348 DP(NETIF_MSG_LINK, "Flow Ctrl AN mismatch %x vs. %x\n", 349 cur_req_fc_auto_adv, params->req_fc_auto_adv); 350 return LFA_FLOW_CTRL_MISMATCH; 351 } 352 353 eee_status = REG_RD(bp, params->shmem2_base + 354 offsetof(struct shmem2_region, 355 eee_status[params->port])); 356 357 if (((eee_status & SHMEM_EEE_LPI_REQUESTED_BIT) ^ 358 (params->eee_mode & EEE_MODE_ENABLE_LPI)) || 359 ((eee_status & SHMEM_EEE_REQUESTED_BIT) ^ 360 (params->eee_mode & EEE_MODE_ADV_LPI))) { 361 DP(NETIF_MSG_LINK, "EEE mismatch %x vs. %x\n", params->eee_mode, 362 eee_status); 363 return LFA_EEE_MISMATCH; 364 } 365 366 /* LFA conditions are met */ 367 return 0; 368} 369/******************************************************************/ 370/* EPIO/GPIO section */ 371/******************************************************************/ 372static void bnx2x_get_epio(struct bnx2x *bp, u32 epio_pin, u32 *en) 373{ 374 u32 epio_mask, gp_oenable; 375 *en = 0; 376 /* Sanity check */ 377 if (epio_pin > 31) { 378 DP(NETIF_MSG_LINK, "Invalid EPIO pin %d to get\n", epio_pin); 379 return; 380 } 381 382 epio_mask = 1 << epio_pin; 383 /* Set this EPIO to output */ 384 gp_oenable = REG_RD(bp, MCP_REG_MCPR_GP_OENABLE); 385 REG_WR(bp, MCP_REG_MCPR_GP_OENABLE, gp_oenable & ~epio_mask); 386 387 *en = (REG_RD(bp, MCP_REG_MCPR_GP_INPUTS) & epio_mask) >> epio_pin; 388} 389static void bnx2x_set_epio(struct bnx2x *bp, u32 epio_pin, u32 en) 390{ 391 u32 epio_mask, gp_output, gp_oenable; 392 393 /* Sanity check */ 394 if (epio_pin > 31) { 395 DP(NETIF_MSG_LINK, "Invalid EPIO pin %d to set\n", epio_pin); 396 return; 397 } 398 DP(NETIF_MSG_LINK, "Setting EPIO pin %d to %d\n", epio_pin, en); 399 epio_mask = 1 << epio_pin; 400 /* Set this EPIO to output */ 401 gp_output = REG_RD(bp, MCP_REG_MCPR_GP_OUTPUTS); 402 if (en) 403 gp_output |= epio_mask; 404 else 405 gp_output &= ~epio_mask; 406 407 REG_WR(bp, MCP_REG_MCPR_GP_OUTPUTS, gp_output); 408 409 /* Set the value for this EPIO */ 410 gp_oenable = REG_RD(bp, MCP_REG_MCPR_GP_OENABLE); 411 REG_WR(bp, MCP_REG_MCPR_GP_OENABLE, gp_oenable | epio_mask); 412} 413 414static void bnx2x_set_cfg_pin(struct bnx2x *bp, u32 pin_cfg, u32 val) 415{ 416 if (pin_cfg == PIN_CFG_NA) 417 return; 418 if (pin_cfg >= PIN_CFG_EPIO0) { 419 bnx2x_set_epio(bp, pin_cfg - PIN_CFG_EPIO0, val); 420 } else { 421 u8 gpio_num = (pin_cfg - PIN_CFG_GPIO0_P0) & 0x3; 422 u8 gpio_port = (pin_cfg - PIN_CFG_GPIO0_P0) >> 2; 423 bnx2x_set_gpio(bp, gpio_num, (u8)val, gpio_port); 424 } 425} 426 427static u32 bnx2x_get_cfg_pin(struct bnx2x *bp, u32 pin_cfg, u32 *val) 428{ 429 if (pin_cfg == PIN_CFG_NA) 430 return -EINVAL; 431 if (pin_cfg >= PIN_CFG_EPIO0) { 432 bnx2x_get_epio(bp, pin_cfg - PIN_CFG_EPIO0, val); 433 } else { 434 u8 gpio_num = (pin_cfg - PIN_CFG_GPIO0_P0) & 0x3; 435 u8 gpio_port = (pin_cfg - PIN_CFG_GPIO0_P0) >> 2; 436 *val = bnx2x_get_gpio(bp, gpio_num, gpio_port); 437 } 438 return 0; 439 440} 441/******************************************************************/ 442/* ETS section */ 443/******************************************************************/ 444static void bnx2x_ets_e2e3a0_disabled(struct link_params *params) 445{ 446 /* ETS disabled configuration*/ 447 struct bnx2x *bp = params->bp; 448 449 DP(NETIF_MSG_LINK, "ETS E2E3 disabled configuration\n"); 450 451 /* mapping between entry priority to client number (0,1,2 -debug and 452 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST) 453 * 3bits client num. 454 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 455 * cos1-100 cos0-011 dbg1-010 dbg0-001 MCP-000 456 */ 457 458 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, 0x4688); 459 /* Bitmap of 5bits length. Each bit specifies whether the entry behaves 460 * as strict. Bits 0,1,2 - debug and management entries, 3 - 461 * COS0 entry, 4 - COS1 entry. 462 * COS1 | COS0 | DEBUG1 | DEBUG0 | MGMT 463 * bit4 bit3 bit2 bit1 bit0 464 * MCP and debug are strict 465 */ 466 467 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7); 468 /* defines which entries (clients) are subjected to WFQ arbitration */ 469 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0); 470 /* For strict priority entries defines the number of consecutive 471 * slots for the highest priority. 472 */ 473 REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100); 474 /* mapping between the CREDIT_WEIGHT registers and actual client 475 * numbers 476 */ 477 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0); 478 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, 0); 479 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, 0); 480 481 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, 0); 482 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, 0); 483 REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, 0); 484 /* ETS mode disable */ 485 REG_WR(bp, PBF_REG_ETS_ENABLED, 0); 486 /* If ETS mode is enabled (there is no strict priority) defines a WFQ 487 * weight for COS0/COS1. 488 */ 489 REG_WR(bp, PBF_REG_COS0_WEIGHT, 0x2710); 490 REG_WR(bp, PBF_REG_COS1_WEIGHT, 0x2710); 491 /* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter */ 492 REG_WR(bp, PBF_REG_COS0_UPPER_BOUND, 0x989680); 493 REG_WR(bp, PBF_REG_COS1_UPPER_BOUND, 0x989680); 494 /* Defines the number of consecutive slots for the strict priority */ 495 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0); 496} 497/****************************************************************************** 498* Description: 499* Getting min_w_val will be set according to line speed . 500*. 501******************************************************************************/ 502static u32 bnx2x_ets_get_min_w_val_nig(const struct link_vars *vars) 503{ 504 u32 min_w_val = 0; 505 /* Calculate min_w_val.*/ 506 if (vars->link_up) { 507 if (vars->line_speed == SPEED_20000) 508 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_20GBPS; 509 else 510 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_UP_TO_10GBPS; 511 } else 512 min_w_val = ETS_E3B0_NIG_MIN_W_VAL_20GBPS; 513 /* If the link isn't up (static configuration for example ) The 514 * link will be according to 20GBPS. 515 */ 516 return min_w_val; 517} 518/****************************************************************************** 519* Description: 520* Getting credit upper bound form min_w_val. 521*. 522******************************************************************************/ 523static u32 bnx2x_ets_get_credit_upper_bound(const u32 min_w_val) 524{ 525 const u32 credit_upper_bound = (u32)MAXVAL((150 * min_w_val), 526 MAX_PACKET_SIZE); 527 return credit_upper_bound; 528} 529/****************************************************************************** 530* Description: 531* Set credit upper bound for NIG. 532*. 533******************************************************************************/ 534static void bnx2x_ets_e3b0_set_credit_upper_bound_nig( 535 const struct link_params *params, 536 const u32 min_w_val) 537{ 538 struct bnx2x *bp = params->bp; 539 const u8 port = params->port; 540 const u32 credit_upper_bound = 541 bnx2x_ets_get_credit_upper_bound(min_w_val); 542 543 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_0 : 544 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, credit_upper_bound); 545 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_1 : 546 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, credit_upper_bound); 547 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_2 : 548 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_2, credit_upper_bound); 549 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_3 : 550 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_3, credit_upper_bound); 551 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_4 : 552 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_4, credit_upper_bound); 553 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_5 : 554 NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_5, credit_upper_bound); 555 556 if (!port) { 557 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_6, 558 credit_upper_bound); 559 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_7, 560 credit_upper_bound); 561 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_8, 562 credit_upper_bound); 563 } 564} 565/****************************************************************************** 566* Description: 567* Will return the NIG ETS registers to init values.Except 568* credit_upper_bound. 569* That isn't used in this configuration (No WFQ is enabled) and will be 570* configured according to spec 571*. 572******************************************************************************/ 573static void bnx2x_ets_e3b0_nig_disabled(const struct link_params *params, 574 const struct link_vars *vars) 575{ 576 struct bnx2x *bp = params->bp; 577 const u8 port = params->port; 578 const u32 min_w_val = bnx2x_ets_get_min_w_val_nig(vars); 579 /* Mapping between entry priority to client number (0,1,2 -debug and 580 * management clients, 3 - COS0 client, 4 - COS1, ... 8 - 581 * COS5)(HIGHEST) 4bits client num.TODO_ETS - Should be done by 582 * reset value or init tool 583 */ 584 if (port) { 585 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB, 0x543210); 586 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_MSB, 0x0); 587 } else { 588 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB, 0x76543210); 589 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB, 0x8); 590 } 591 /* For strict priority entries defines the number of consecutive 592 * slots for the highest priority. 593 */ 594 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS : 595 NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100); 596 /* Mapping between the CREDIT_WEIGHT registers and actual client 597 * numbers 598 */ 599 if (port) { 600 /*Port 1 has 6 COS*/ 601 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_LSB, 0x210543); 602 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_MSB, 0x0); 603 } else { 604 /*Port 0 has 9 COS*/ 605 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_LSB, 606 0x43210876); 607 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_MSB, 0x5); 608 } 609 610 /* Bitmap of 5bits length. Each bit specifies whether the entry behaves 611 * as strict. Bits 0,1,2 - debug and management entries, 3 - 612 * COS0 entry, 4 - COS1 entry. 613 * COS1 | COS0 | DEBUG1 | DEBUG0 | MGMT 614 * bit4 bit3 bit2 bit1 bit0 615 * MCP and debug are strict 616 */ 617 if (port) 618 REG_WR(bp, NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT, 0x3f); 619 else 620 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1ff); 621 /* defines which entries (clients) are subjected to WFQ arbitration */ 622 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ : 623 NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0); 624 625 /* Please notice the register address are note continuous and a 626 * for here is note appropriate.In 2 port mode port0 only COS0-5 627 * can be used. DEBUG1,DEBUG1,MGMT are never used for WFQ* In 4 628 * port mode port1 only COS0-2 can be used. DEBUG1,DEBUG1,MGMT 629 * are never used for WFQ 630 */ 631 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 : 632 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, 0x0); 633 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 : 634 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, 0x0); 635 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 : 636 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2, 0x0); 637 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_3 : 638 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3, 0x0); 639 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_4 : 640 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4, 0x0); 641 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_5 : 642 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5, 0x0); 643 if (!port) { 644 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_6, 0x0); 645 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_7, 0x0); 646 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_8, 0x0); 647 } 648 649 bnx2x_ets_e3b0_set_credit_upper_bound_nig(params, min_w_val); 650} 651/****************************************************************************** 652* Description: 653* Set credit upper bound for PBF. 654*. 655******************************************************************************/ 656static void bnx2x_ets_e3b0_set_credit_upper_bound_pbf( 657 const struct link_params *params, 658 const u32 min_w_val) 659{ 660 struct bnx2x *bp = params->bp; 661 const u32 credit_upper_bound = 662 bnx2x_ets_get_credit_upper_bound(min_w_val); 663 const u8 port = params->port; 664 u32 base_upper_bound = 0; 665 u8 max_cos = 0; 666 u8 i = 0; 667 /* In 2 port mode port0 has COS0-5 that can be used for WFQ.In 4 668 * port mode port1 has COS0-2 that can be used for WFQ. 669 */ 670 if (!port) { 671 base_upper_bound = PBF_REG_COS0_UPPER_BOUND_P0; 672 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT0; 673 } else { 674 base_upper_bound = PBF_REG_COS0_UPPER_BOUND_P1; 675 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT1; 676 } 677 678 for (i = 0; i < max_cos; i++) 679 REG_WR(bp, base_upper_bound + (i << 2), credit_upper_bound); 680} 681 682/****************************************************************************** 683* Description: 684* Will return the PBF ETS registers to init values.Except 685* credit_upper_bound. 686* That isn't used in this configuration (No WFQ is enabled) and will be 687* configured according to spec 688*. 689******************************************************************************/ 690static void bnx2x_ets_e3b0_pbf_disabled(const struct link_params *params) 691{ 692 struct bnx2x *bp = params->bp; 693 const u8 port = params->port; 694 const u32 min_w_val_pbf = ETS_E3B0_PBF_MIN_W_VAL; 695 u8 i = 0; 696 u32 base_weight = 0; 697 u8 max_cos = 0; 698 699 /* Mapping between entry priority to client number 0 - COS0 700 * client, 2 - COS1, ... 5 - COS5)(HIGHEST) 4bits client num. 701 * TODO_ETS - Should be done by reset value or init tool 702 */ 703 if (port) 704 /* 0x688 (|011|0 10|00 1|000) */ 705 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 , 0x688); 706 else 707 /* (10 1|100 |011|0 10|00 1|000) */ 708 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 , 0x2C688); 709 710 /* TODO_ETS - Should be done by reset value or init tool */ 711 if (port) 712 /* 0x688 (|011|0 10|00 1|000)*/ 713 REG_WR(bp, PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P1, 0x688); 714 else 715 /* 0x2C688 (10 1|100 |011|0 10|00 1|000) */ 716 REG_WR(bp, PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P0, 0x2C688); 717 718 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P1 : 719 PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P0 , 0x100); 720 721 722 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 : 723 PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 , 0); 724 725 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 : 726 PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0 , 0); 727 /* In 2 port mode port0 has COS0-5 that can be used for WFQ. 728 * In 4 port mode port1 has COS0-2 that can be used for WFQ. 729 */ 730 if (!port) { 731 base_weight = PBF_REG_COS0_WEIGHT_P0; 732 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT0; 733 } else { 734 base_weight = PBF_REG_COS0_WEIGHT_P1; 735 max_cos = DCBX_E3B0_MAX_NUM_COS_PORT1; 736 } 737 738 for (i = 0; i < max_cos; i++) 739 REG_WR(bp, base_weight + (0x4 * i), 0); 740 741 bnx2x_ets_e3b0_set_credit_upper_bound_pbf(params, min_w_val_pbf); 742} 743/****************************************************************************** 744* Description: 745* E3B0 disable will return basically the values to init values. 746*. 747******************************************************************************/ 748static int bnx2x_ets_e3b0_disabled(const struct link_params *params, 749 const struct link_vars *vars) 750{ 751 struct bnx2x *bp = params->bp; 752 753 if (!CHIP_IS_E3B0(bp)) { 754 DP(NETIF_MSG_LINK, 755 "bnx2x_ets_e3b0_disabled the chip isn't E3B0\n"); 756 return -EINVAL; 757 } 758 759 bnx2x_ets_e3b0_nig_disabled(params, vars); 760 761 bnx2x_ets_e3b0_pbf_disabled(params); 762 763 return 0; 764} 765 766/****************************************************************************** 767* Description: 768* Disable will return basically the values to init values. 769* 770******************************************************************************/ 771int bnx2x_ets_disabled(struct link_params *params, 772 struct link_vars *vars) 773{ 774 struct bnx2x *bp = params->bp; 775 int bnx2x_status = 0; 776 777 if ((CHIP_IS_E2(bp)) || (CHIP_IS_E3A0(bp))) 778 bnx2x_ets_e2e3a0_disabled(params); 779 else if (CHIP_IS_E3B0(bp)) 780 bnx2x_status = bnx2x_ets_e3b0_disabled(params, vars); 781 else { 782 DP(NETIF_MSG_LINK, "bnx2x_ets_disabled - chip not supported\n"); 783 return -EINVAL; 784 } 785 786 return bnx2x_status; 787} 788 789/****************************************************************************** 790* Description 791* Set the COS mappimg to SP and BW until this point all the COS are not 792* set as SP or BW. 793******************************************************************************/ 794static int bnx2x_ets_e3b0_cli_map(const struct link_params *params, 795 const struct bnx2x_ets_params *ets_params, 796 const u8 cos_sp_bitmap, 797 const u8 cos_bw_bitmap) 798{ 799 struct bnx2x *bp = params->bp; 800 const u8 port = params->port; 801 const u8 nig_cli_sp_bitmap = 0x7 | (cos_sp_bitmap << 3); 802 const u8 pbf_cli_sp_bitmap = cos_sp_bitmap; 803 const u8 nig_cli_subject2wfq_bitmap = cos_bw_bitmap << 3; 804 const u8 pbf_cli_subject2wfq_bitmap = cos_bw_bitmap; 805 806 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT : 807 NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, nig_cli_sp_bitmap); 808 809 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 : 810 PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 , pbf_cli_sp_bitmap); 811 812 REG_WR(bp, (port) ? NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ : 813 NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 814 nig_cli_subject2wfq_bitmap); 815 816 REG_WR(bp, (port) ? PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 : 817 PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0, 818 pbf_cli_subject2wfq_bitmap); 819 820 return 0; 821} 822 823/****************************************************************************** 824* Description: 825* This function is needed because NIG ARB_CREDIT_WEIGHT_X are 826* not continues and ARB_CREDIT_WEIGHT_0 + offset is suitable. 827******************************************************************************/ 828static int bnx2x_ets_e3b0_set_cos_bw(struct bnx2x *bp, 829 const u8 cos_entry, 830 const u32 min_w_val_nig, 831 const u32 min_w_val_pbf, 832 const u16 total_bw, 833 const u8 bw, 834 const u8 port) 835{ 836 u32 nig_reg_adress_crd_weight = 0; 837 u32 pbf_reg_adress_crd_weight = 0; 838 /* Calculate and set BW for this COS - use 1 instead of 0 for BW */ 839 const u32 cos_bw_nig = ((bw ? bw : 1) * min_w_val_nig) / total_bw; 840 const u32 cos_bw_pbf = ((bw ? bw : 1) * min_w_val_pbf) / total_bw; 841 842 switch (cos_entry) { 843 case 0: 844 nig_reg_adress_crd_weight = 845 (port) ? NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 : 846 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0; 847 pbf_reg_adress_crd_weight = (port) ? 848 PBF_REG_COS0_WEIGHT_P1 : PBF_REG_COS0_WEIGHT_P0; 849 break; 850 case 1: 851 nig_reg_adress_crd_weight = (port) ? 852 NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 : 853 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1; 854 pbf_reg_adress_crd_weight = (port) ? 855 PBF_REG_COS1_WEIGHT_P1 : PBF_REG_COS1_WEIGHT_P0; 856 break; 857 case 2: 858 nig_reg_adress_crd_weight = (port) ? 859 NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 : 860 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2; 861 862 pbf_reg_adress_crd_weight = (port) ? 863 PBF_REG_COS2_WEIGHT_P1 : PBF_REG_COS2_WEIGHT_P0; 864 break; 865 case 3: 866 if (port) 867 return -EINVAL; 868 nig_reg_adress_crd_weight = 869 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3; 870 pbf_reg_adress_crd_weight = 871 PBF_REG_COS3_WEIGHT_P0; 872 break; 873 case 4: 874 if (port) 875 return -EINVAL; 876 nig_reg_adress_crd_weight = 877 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4; 878 pbf_reg_adress_crd_weight = PBF_REG_COS4_WEIGHT_P0; 879 break; 880 case 5: 881 if (port) 882 return -EINVAL; 883 nig_reg_adress_crd_weight = 884 NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5; 885 pbf_reg_adress_crd_weight = PBF_REG_COS5_WEIGHT_P0; 886 break; 887 } 888 889 REG_WR(bp, nig_reg_adress_crd_weight, cos_bw_nig); 890 891 REG_WR(bp, pbf_reg_adress_crd_weight, cos_bw_pbf); 892 893 return 0; 894} 895/****************************************************************************** 896* Description: 897* Calculate the total BW.A value of 0 isn't legal. 898* 899******************************************************************************/ 900static int bnx2x_ets_e3b0_get_total_bw( 901 const struct link_params *params, 902 struct bnx2x_ets_params *ets_params, 903 u16 *total_bw) 904{ 905 struct bnx2x *bp = params->bp; 906 u8 cos_idx = 0; 907 u8 is_bw_cos_exist = 0; 908 909 *total_bw = 0 ; 910 /* Calculate total BW requested */ 911 for (cos_idx = 0; cos_idx < ets_params->num_of_cos; cos_idx++) { 912 if (ets_params->cos[cos_idx].state == bnx2x_cos_state_bw) { 913 is_bw_cos_exist = 1; 914 if (!ets_params->cos[cos_idx].params.bw_params.bw) { 915 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config BW" 916 "was set to 0\n"); 917 /* This is to prevent a state when ramrods 918 * can't be sent 919 */ 920 ets_params->cos[cos_idx].params.bw_params.bw 921 = 1; 922 } 923 *total_bw += 924 ets_params->cos[cos_idx].params.bw_params.bw; 925 } 926 } 927 928 /* Check total BW is valid */ 929 if ((is_bw_cos_exist == 1) && (*total_bw != 100)) { 930 if (*total_bw == 0) { 931 DP(NETIF_MSG_LINK, 932 "bnx2x_ets_E3B0_config total BW shouldn't be 0\n"); 933 return -EINVAL; 934 } 935 DP(NETIF_MSG_LINK, 936 "bnx2x_ets_E3B0_config total BW should be 100\n"); 937 /* We can handle a case whre the BW isn't 100 this can happen 938 * if the TC are joined. 939 */ 940 } 941 return 0; 942} 943 944/****************************************************************************** 945* Description: 946* Invalidate all the sp_pri_to_cos. 947* 948******************************************************************************/ 949static void bnx2x_ets_e3b0_sp_pri_to_cos_init(u8 *sp_pri_to_cos) 950{ 951 u8 pri = 0; 952 for (pri = 0; pri < DCBX_MAX_NUM_COS; pri++) 953 sp_pri_to_cos[pri] = DCBX_INVALID_COS; 954} 955/****************************************************************************** 956* Description: 957* Calculate and set the SP (ARB_PRIORITY_CLIENT) NIG and PBF registers 958* according to sp_pri_to_cos. 959* 960******************************************************************************/ 961static int bnx2x_ets_e3b0_sp_pri_to_cos_set(const struct link_params *params, 962 u8 *sp_pri_to_cos, const u8 pri, 963 const u8 cos_entry) 964{ 965 struct bnx2x *bp = params->bp; 966 const u8 port = params->port; 967 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 : 968 DCBX_E3B0_MAX_NUM_COS_PORT0; 969 970 if (pri >= max_num_of_cos) { 971 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid " 972 "parameter Illegal strict priority\n"); 973 return -EINVAL; 974 } 975 976 if (sp_pri_to_cos[pri] != DCBX_INVALID_COS) { 977 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_pri_to_cos_set invalid " 978 "parameter There can't be two COS's with " 979 "the same strict pri\n"); 980 return -EINVAL; 981 } 982 983 sp_pri_to_cos[pri] = cos_entry; 984 return 0; 985 986} 987 988/****************************************************************************** 989* Description: 990* Returns the correct value according to COS and priority in 991* the sp_pri_cli register. 992* 993******************************************************************************/ 994static u64 bnx2x_e3b0_sp_get_pri_cli_reg(const u8 cos, const u8 cos_offset, 995 const u8 pri_set, 996 const u8 pri_offset, 997 const u8 entry_size) 998{ 999 u64 pri_cli_nig = 0; 1000 pri_cli_nig = ((u64)(cos + cos_offset)) << (entry_size * 1001 (pri_set + pri_offset)); 1002 1003 return pri_cli_nig; 1004} 1005/****************************************************************************** 1006* Description: 1007* Returns the correct value according to COS and priority in the 1008* sp_pri_cli register for NIG. 1009* 1010******************************************************************************/ 1011static u64 bnx2x_e3b0_sp_get_pri_cli_reg_nig(const u8 cos, const u8 pri_set) 1012{ 1013 /* MCP Dbg0 and dbg1 are always with higher strict pri*/ 1014 const u8 nig_cos_offset = 3; 1015 const u8 nig_pri_offset = 3; 1016 1017 return bnx2x_e3b0_sp_get_pri_cli_reg(cos, nig_cos_offset, pri_set, 1018 nig_pri_offset, 4); 1019 1020} 1021/****************************************************************************** 1022* Description: 1023* Returns the correct value according to COS and priority in the 1024* sp_pri_cli register for PBF. 1025* 1026******************************************************************************/ 1027static u64 bnx2x_e3b0_sp_get_pri_cli_reg_pbf(const u8 cos, const u8 pri_set) 1028{ 1029 const u8 pbf_cos_offset = 0; 1030 const u8 pbf_pri_offset = 0; 1031 1032 return bnx2x_e3b0_sp_get_pri_cli_reg(cos, pbf_cos_offset, pri_set, 1033 pbf_pri_offset, 3); 1034 1035} 1036 1037/****************************************************************************** 1038* Description: 1039* Calculate and set the SP (ARB_PRIORITY_CLIENT) NIG and PBF registers 1040* according to sp_pri_to_cos.(which COS has higher priority) 1041* 1042******************************************************************************/ 1043static int bnx2x_ets_e3b0_sp_set_pri_cli_reg(const struct link_params *params, 1044 u8 *sp_pri_to_cos) 1045{ 1046 struct bnx2x *bp = params->bp; 1047 u8 i = 0; 1048 const u8 port = params->port; 1049 /* MCP Dbg0 and dbg1 are always with higher strict pri*/ 1050 u64 pri_cli_nig = 0x210; 1051 u32 pri_cli_pbf = 0x0; 1052 u8 pri_set = 0; 1053 u8 pri_bitmask = 0; 1054 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 : 1055 DCBX_E3B0_MAX_NUM_COS_PORT0; 1056 1057 u8 cos_bit_to_set = (1 << max_num_of_cos) - 1; 1058 1059 /* Set all the strict priority first */ 1060 for (i = 0; i < max_num_of_cos; i++) { 1061 if (sp_pri_to_cos[i] != DCBX_INVALID_COS) { 1062 if (sp_pri_to_cos[i] >= DCBX_MAX_NUM_COS) { 1063 DP(NETIF_MSG_LINK, 1064 "bnx2x_ets_e3b0_sp_set_pri_cli_reg " 1065 "invalid cos entry\n"); 1066 return -EINVAL; 1067 } 1068 1069 pri_cli_nig |= bnx2x_e3b0_sp_get_pri_cli_reg_nig( 1070 sp_pri_to_cos[i], pri_set); 1071 1072 pri_cli_pbf |= bnx2x_e3b0_sp_get_pri_cli_reg_pbf( 1073 sp_pri_to_cos[i], pri_set); 1074 pri_bitmask = 1 << sp_pri_to_cos[i]; 1075 /* COS is used remove it from bitmap.*/ 1076 if (!(pri_bitmask & cos_bit_to_set)) { 1077 DP(NETIF_MSG_LINK, 1078 "bnx2x_ets_e3b0_sp_set_pri_cli_reg " 1079 "invalid There can't be two COS's with" 1080 " the same strict pri\n"); 1081 return -EINVAL; 1082 } 1083 cos_bit_to_set &= ~pri_bitmask; 1084 pri_set++; 1085 } 1086 } 1087 1088 /* Set all the Non strict priority i= COS*/ 1089 for (i = 0; i < max_num_of_cos; i++) { 1090 pri_bitmask = 1 << i; 1091 /* Check if COS was already used for SP */ 1092 if (pri_bitmask & cos_bit_to_set) { 1093 /* COS wasn't used for SP */ 1094 pri_cli_nig |= bnx2x_e3b0_sp_get_pri_cli_reg_nig( 1095 i, pri_set); 1096 1097 pri_cli_pbf |= bnx2x_e3b0_sp_get_pri_cli_reg_pbf( 1098 i, pri_set); 1099 /* COS is used remove it from bitmap.*/ 1100 cos_bit_to_set &= ~pri_bitmask; 1101 pri_set++; 1102 } 1103 } 1104 1105 if (pri_set != max_num_of_cos) { 1106 DP(NETIF_MSG_LINK, "bnx2x_ets_e3b0_sp_set_pri_cli_reg not all " 1107 "entries were set\n"); 1108 return -EINVAL; 1109 } 1110 1111 if (port) { 1112 /* Only 6 usable clients*/ 1113 REG_WR(bp, NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB, 1114 (u32)pri_cli_nig); 1115 1116 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 , pri_cli_pbf); 1117 } else { 1118 /* Only 9 usable clients*/ 1119 const u32 pri_cli_nig_lsb = (u32) (pri_cli_nig); 1120 const u32 pri_cli_nig_msb = (u32) ((pri_cli_nig >> 32) & 0xF); 1121 1122 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB, 1123 pri_cli_nig_lsb); 1124 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB, 1125 pri_cli_nig_msb); 1126 1127 REG_WR(bp, PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 , pri_cli_pbf); 1128 } 1129 return 0; 1130} 1131 1132/****************************************************************************** 1133* Description: 1134* Configure the COS to ETS according to BW and SP settings. 1135******************************************************************************/ 1136int bnx2x_ets_e3b0_config(const struct link_params *params, 1137 const struct link_vars *vars, 1138 struct bnx2x_ets_params *ets_params) 1139{ 1140 struct bnx2x *bp = params->bp; 1141 int bnx2x_status = 0; 1142 const u8 port = params->port; 1143 u16 total_bw = 0; 1144 const u32 min_w_val_nig = bnx2x_ets_get_min_w_val_nig(vars); 1145 const u32 min_w_val_pbf = ETS_E3B0_PBF_MIN_W_VAL; 1146 u8 cos_bw_bitmap = 0; 1147 u8 cos_sp_bitmap = 0; 1148 u8 sp_pri_to_cos[DCBX_MAX_NUM_COS] = {0}; 1149 const u8 max_num_of_cos = (port) ? DCBX_E3B0_MAX_NUM_COS_PORT1 : 1150 DCBX_E3B0_MAX_NUM_COS_PORT0; 1151 u8 cos_entry = 0; 1152 1153 if (!CHIP_IS_E3B0(bp)) { 1154 DP(NETIF_MSG_LINK, 1155 "bnx2x_ets_e3b0_disabled the chip isn't E3B0\n"); 1156 return -EINVAL; 1157 } 1158 1159 if ((ets_params->num_of_cos > max_num_of_cos)) { 1160 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config the number of COS " 1161 "isn't supported\n"); 1162 return -EINVAL; 1163 } 1164 1165 /* Prepare sp strict priority parameters*/ 1166 bnx2x_ets_e3b0_sp_pri_to_cos_init(sp_pri_to_cos); 1167 1168 /* Prepare BW parameters*/ 1169 bnx2x_status = bnx2x_ets_e3b0_get_total_bw(params, ets_params, 1170 &total_bw); 1171 if (bnx2x_status) { 1172 DP(NETIF_MSG_LINK, 1173 "bnx2x_ets_E3B0_config get_total_bw failed\n"); 1174 return -EINVAL; 1175 } 1176 1177 /* Upper bound is set according to current link speed (min_w_val 1178 * should be the same for upper bound and COS credit val). 1179 */ 1180 bnx2x_ets_e3b0_set_credit_upper_bound_nig(params, min_w_val_nig); 1181 bnx2x_ets_e3b0_set_credit_upper_bound_pbf(params, min_w_val_pbf); 1182 1183 1184 for (cos_entry = 0; cos_entry < ets_params->num_of_cos; cos_entry++) { 1185 if (bnx2x_cos_state_bw == ets_params->cos[cos_entry].state) { 1186 cos_bw_bitmap |= (1 << cos_entry); 1187 /* The function also sets the BW in HW(not the mappin 1188 * yet) 1189 */ 1190 bnx2x_status = bnx2x_ets_e3b0_set_cos_bw( 1191 bp, cos_entry, min_w_val_nig, min_w_val_pbf, 1192 total_bw, 1193 ets_params->cos[cos_entry].params.bw_params.bw, 1194 port); 1195 } else if (bnx2x_cos_state_strict == 1196 ets_params->cos[cos_entry].state){ 1197 cos_sp_bitmap |= (1 << cos_entry); 1198 1199 bnx2x_status = bnx2x_ets_e3b0_sp_pri_to_cos_set( 1200 params, 1201 sp_pri_to_cos, 1202 ets_params->cos[cos_entry].params.sp_params.pri, 1203 cos_entry); 1204 1205 } else { 1206 DP(NETIF_MSG_LINK, 1207 "bnx2x_ets_e3b0_config cos state not valid\n"); 1208 return -EINVAL; 1209 } 1210 if (bnx2x_status) { 1211 DP(NETIF_MSG_LINK, 1212 "bnx2x_ets_e3b0_config set cos bw failed\n"); 1213 return bnx2x_status; 1214 } 1215 } 1216 1217 /* Set SP register (which COS has higher priority) */ 1218 bnx2x_status = bnx2x_ets_e3b0_sp_set_pri_cli_reg(params, 1219 sp_pri_to_cos); 1220 1221 if (bnx2x_status) { 1222 DP(NETIF_MSG_LINK, 1223 "bnx2x_ets_E3B0_config set_pri_cli_reg failed\n"); 1224 return bnx2x_status; 1225 } 1226 1227 /* Set client mapping of BW and strict */ 1228 bnx2x_status = bnx2x_ets_e3b0_cli_map(params, ets_params, 1229 cos_sp_bitmap, 1230 cos_bw_bitmap); 1231 1232 if (bnx2x_status) { 1233 DP(NETIF_MSG_LINK, "bnx2x_ets_E3B0_config SP failed\n"); 1234 return bnx2x_status; 1235 } 1236 return 0; 1237} 1238static void bnx2x_ets_bw_limit_common(const struct link_params *params) 1239{ 1240 /* ETS disabled configuration */ 1241 struct bnx2x *bp = params->bp; 1242 DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n"); 1243 /* Defines which entries (clients) are subjected to WFQ arbitration 1244 * COS0 0x8 1245 * COS1 0x10 1246 */ 1247 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0x18); 1248 /* Mapping between the ARB_CREDIT_WEIGHT registers and actual 1249 * client numbers (WEIGHT_0 does not actually have to represent 1250 * client 0) 1251 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 1252 * cos1-001 cos0-000 dbg1-100 dbg0-011 MCP-010 1253 */ 1254 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0x111A); 1255 1256 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, 1257 ETS_BW_LIMIT_CREDIT_UPPER_BOUND); 1258 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1, 1259 ETS_BW_LIMIT_CREDIT_UPPER_BOUND); 1260 1261 /* ETS mode enabled*/ 1262 REG_WR(bp, PBF_REG_ETS_ENABLED, 1); 1263 1264 /* Defines the number of consecutive slots for the strict priority */ 1265 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0); 1266 /* Bitmap of 5bits length. Each bit specifies whether the entry behaves 1267 * as strict. Bits 0,1,2 - debug and management entries, 3 - COS0 1268 * entry, 4 - COS1 entry. 1269 * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT 1270 * bit4 bit3 bit2 bit1 bit0 1271 * MCP and debug are strict 1272 */ 1273 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7); 1274 1275 /* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter.*/ 1276 REG_WR(bp, PBF_REG_COS0_UPPER_BOUND, 1277 ETS_BW_LIMIT_CREDIT_UPPER_BOUND); 1278 REG_WR(bp, PBF_REG_COS1_UPPER_BOUND, 1279 ETS_BW_LIMIT_CREDIT_UPPER_BOUND); 1280} 1281 1282void bnx2x_ets_bw_limit(const struct link_params *params, const u32 cos0_bw, 1283 const u32 cos1_bw) 1284{ 1285 /* ETS disabled configuration*/ 1286 struct bnx2x *bp = params->bp; 1287 const u32 total_bw = cos0_bw + cos1_bw; 1288 u32 cos0_credit_weight = 0; 1289 u32 cos1_credit_weight = 0; 1290 1291 DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n"); 1292 1293 if ((!total_bw) || 1294 (!cos0_bw) || 1295 (!cos1_bw)) { 1296 DP(NETIF_MSG_LINK, "Total BW can't be zero\n"); 1297 return; 1298 } 1299 1300 cos0_credit_weight = (cos0_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/ 1301 total_bw; 1302 cos1_credit_weight = (cos1_bw * ETS_BW_LIMIT_CREDIT_WEIGHT)/ 1303 total_bw; 1304 1305 bnx2x_ets_bw_limit_common(params); 1306 1307 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0, cos0_credit_weight); 1308 REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1, cos1_credit_weight); 1309 1310 REG_WR(bp, PBF_REG_COS0_WEIGHT, cos0_credit_weight); 1311 REG_WR(bp, PBF_REG_COS1_WEIGHT, cos1_credit_weight); 1312} 1313 1314int bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos) 1315{ 1316 /* ETS disabled configuration*/ 1317 struct bnx2x *bp = params->bp; 1318 u32 val = 0; 1319 1320 DP(NETIF_MSG_LINK, "ETS enabled strict configuration\n"); 1321 /* Bitmap of 5bits length. Each bit specifies whether the entry behaves 1322 * as strict. Bits 0,1,2 - debug and management entries, 1323 * 3 - COS0 entry, 4 - COS1 entry. 1324 * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT 1325 * bit4 bit3 bit2 bit1 bit0 1326 * MCP and debug are strict 1327 */ 1328 REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1F); 1329 /* For strict priority entries defines the number of consecutive slots 1330 * for the highest priority. 1331 */ 1332 REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100); 1333 /* ETS mode disable */ 1334 REG_WR(bp, PBF_REG_ETS_ENABLED, 0); 1335 /* Defines the number of consecutive slots for the strict priority */ 1336 REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0x100); 1337 1338 /* Defines the number of consecutive slots for the strict priority */ 1339 REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, strict_cos); 1340 1341 /* Mapping between entry priority to client number (0,1,2 -debug and 1342 * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST) 1343 * 3bits client num. 1344 * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 1345 * dbg0-010 dbg1-001 cos1-100 cos0-011 MCP-000 1346 * dbg0-010 dbg1-001 cos0-011 cos1-100 MCP-000 1347 */ 1348 val = (!strict_cos) ? 0x2318 : 0x22E0; 1349 REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, val); 1350 1351 return 0; 1352} 1353 1354/******************************************************************/ 1355/* PFC section */ 1356/******************************************************************/ 1357static void bnx2x_update_pfc_xmac(struct link_params *params, 1358 struct link_vars *vars, 1359 u8 is_lb) 1360{ 1361 struct bnx2x *bp = params->bp; 1362 u32 xmac_base; 1363 u32 pause_val, pfc0_val, pfc1_val; 1364 1365 /* XMAC base adrr */ 1366 xmac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; 1367 1368 /* Initialize pause and pfc registers */ 1369 pause_val = 0x18000; 1370 pfc0_val = 0xFFFF8000; 1371 pfc1_val = 0x2; 1372 1373 /* No PFC support */ 1374 if (!(params->feature_config_flags & 1375 FEATURE_CONFIG_PFC_ENABLED)) { 1376 1377 /* RX flow control - Process pause frame in receive direction 1378 */ 1379 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) 1380 pause_val |= XMAC_PAUSE_CTRL_REG_RX_PAUSE_EN; 1381 1382 /* TX flow control - Send pause packet when buffer is full */ 1383 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) 1384 pause_val |= XMAC_PAUSE_CTRL_REG_TX_PAUSE_EN; 1385 } else {/* PFC support */ 1386 pfc1_val |= XMAC_PFC_CTRL_HI_REG_PFC_REFRESH_EN | 1387 XMAC_PFC_CTRL_HI_REG_PFC_STATS_EN | 1388 XMAC_PFC_CTRL_HI_REG_RX_PFC_EN | 1389 XMAC_PFC_CTRL_HI_REG_TX_PFC_EN | 1390 XMAC_PFC_CTRL_HI_REG_FORCE_PFC_XON; 1391 /* Write pause and PFC registers */ 1392 REG_WR(bp, xmac_base + XMAC_REG_PAUSE_CTRL, pause_val); 1393 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL, pfc0_val); 1394 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, pfc1_val); 1395 pfc1_val &= ~XMAC_PFC_CTRL_HI_REG_FORCE_PFC_XON; 1396 1397 } 1398 1399 /* Write pause and PFC registers */ 1400 REG_WR(bp, xmac_base + XMAC_REG_PAUSE_CTRL, pause_val); 1401 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL, pfc0_val); 1402 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, pfc1_val); 1403 1404 1405 /* Set MAC address for source TX Pause/PFC frames */ 1406 REG_WR(bp, xmac_base + XMAC_REG_CTRL_SA_LO, 1407 ((params->mac_addr[2] << 24) | 1408 (params->mac_addr[3] << 16) | 1409 (params->mac_addr[4] << 8) | 1410 (params->mac_addr[5]))); 1411 REG_WR(bp, xmac_base + XMAC_REG_CTRL_SA_HI, 1412 ((params->mac_addr[0] << 8) | 1413 (params->mac_addr[1]))); 1414 1415 udelay(30); 1416} 1417 1418/******************************************************************/ 1419/* MAC/PBF section */ 1420/******************************************************************/ 1421static void bnx2x_set_mdio_clk(struct bnx2x *bp, u32 chip_id, 1422 u32 emac_base) 1423{ 1424 u32 new_mode, cur_mode; 1425 u32 clc_cnt; 1426 /* Set clause 45 mode, slow down the MDIO clock to 2.5MHz 1427 * (a value of 49==0x31) and make sure that the AUTO poll is off 1428 */ 1429 cur_mode = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE); 1430 1431 if (USES_WARPCORE(bp)) 1432 clc_cnt = 74L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT; 1433 else 1434 clc_cnt = 49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT; 1435 1436 if (((cur_mode & EMAC_MDIO_MODE_CLOCK_CNT) == clc_cnt) && 1437 (cur_mode & (EMAC_MDIO_MODE_CLAUSE_45))) 1438 return; 1439 1440 new_mode = cur_mode & 1441 ~(EMAC_MDIO_MODE_AUTO_POLL | EMAC_MDIO_MODE_CLOCK_CNT); 1442 new_mode |= clc_cnt; 1443 new_mode |= (EMAC_MDIO_MODE_CLAUSE_45); 1444 1445 DP(NETIF_MSG_LINK, "Changing emac_mode from 0x%x to 0x%x\n", 1446 cur_mode, new_mode); 1447 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE, new_mode); 1448 udelay(40); 1449} 1450 1451static void bnx2x_set_mdio_emac_per_phy(struct bnx2x *bp, 1452 struct link_params *params) 1453{ 1454 u8 phy_index; 1455 /* Set mdio clock per phy */ 1456 for (phy_index = INT_PHY; phy_index < params->num_phys; 1457 phy_index++) 1458 bnx2x_set_mdio_clk(bp, params->chip_id, 1459 params->phy[phy_index].mdio_ctrl); 1460} 1461 1462static u8 bnx2x_is_4_port_mode(struct bnx2x *bp) 1463{ 1464 u32 port4mode_ovwr_val; 1465 /* Check 4-port override enabled */ 1466 port4mode_ovwr_val = REG_RD(bp, MISC_REG_PORT4MODE_EN_OVWR); 1467 if (port4mode_ovwr_val & (1<<0)) { 1468 /* Return 4-port mode override value */ 1469 return ((port4mode_ovwr_val & (1<<1)) == (1<<1)); 1470 } 1471 /* Return 4-port mode from input pin */ 1472 return (u8)REG_RD(bp, MISC_REG_PORT4MODE_EN); 1473} 1474 1475static void bnx2x_emac_init(struct link_params *params, 1476 struct link_vars *vars) 1477{ 1478 /* reset and unreset the emac core */ 1479 struct bnx2x *bp = params->bp; 1480 u8 port = params->port; 1481 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; 1482 u32 val; 1483 u16 timeout; 1484 1485 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 1486 (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); 1487 udelay(5); 1488 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 1489 (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); 1490 1491 /* init emac - use read-modify-write */ 1492 /* self clear reset */ 1493 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); 1494 EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); 1495 1496 timeout = 200; 1497 do { 1498 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); 1499 DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val); 1500 if (!timeout) { 1501 DP(NETIF_MSG_LINK, "EMAC timeout!\n"); 1502 return; 1503 } 1504 timeout--; 1505 } while (val & EMAC_MODE_RESET); 1506 1507 bnx2x_set_mdio_emac_per_phy(bp, params); 1508 /* Set mac address */ 1509 val = ((params->mac_addr[0] << 8) | 1510 params->mac_addr[1]); 1511 EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val); 1512 1513 val = ((params->mac_addr[2] << 24) | 1514 (params->mac_addr[3] << 16) | 1515 (params->mac_addr[4] << 8) | 1516 params->mac_addr[5]); 1517 EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val); 1518} 1519 1520static void bnx2x_set_xumac_nig(struct link_params *params, 1521 u16 tx_pause_en, 1522 u8 enable) 1523{ 1524 struct bnx2x *bp = params->bp; 1525 1526 REG_WR(bp, params->port ? NIG_REG_P1_MAC_IN_EN : NIG_REG_P0_MAC_IN_EN, 1527 enable); 1528 REG_WR(bp, params->port ? NIG_REG_P1_MAC_OUT_EN : NIG_REG_P0_MAC_OUT_EN, 1529 enable); 1530 REG_WR(bp, params->port ? NIG_REG_P1_MAC_PAUSE_OUT_EN : 1531 NIG_REG_P0_MAC_PAUSE_OUT_EN, tx_pause_en); 1532} 1533 1534static void bnx2x_set_umac_rxtx(struct link_params *params, u8 en) 1535{ 1536 u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0; 1537 u32 val; 1538 struct bnx2x *bp = params->bp; 1539 if (!(REG_RD(bp, MISC_REG_RESET_REG_2) & 1540 (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port))) 1541 return; 1542 val = REG_RD(bp, umac_base + UMAC_REG_COMMAND_CONFIG); 1543 if (en) 1544 val |= (UMAC_COMMAND_CONFIG_REG_TX_ENA | 1545 UMAC_COMMAND_CONFIG_REG_RX_ENA); 1546 else 1547 val &= ~(UMAC_COMMAND_CONFIG_REG_TX_ENA | 1548 UMAC_COMMAND_CONFIG_REG_RX_ENA); 1549 /* Disable RX and TX */ 1550 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val); 1551} 1552 1553static void bnx2x_umac_enable(struct link_params *params, 1554 struct link_vars *vars, u8 lb) 1555{ 1556 u32 val; 1557 u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0; 1558 struct bnx2x *bp = params->bp; 1559 /* Reset UMAC */ 1560 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 1561 (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port)); 1562 usleep_range(1000, 2000); 1563 1564 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 1565 (MISC_REGISTERS_RESET_REG_2_UMAC0 << params->port)); 1566 1567 DP(NETIF_MSG_LINK, "enabling UMAC\n"); 1568 1569 /* This register opens the gate for the UMAC despite its name */ 1570 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 1); 1571 1572 val = UMAC_COMMAND_CONFIG_REG_PROMIS_EN | 1573 UMAC_COMMAND_CONFIG_REG_PAD_EN | 1574 UMAC_COMMAND_CONFIG_REG_SW_RESET | 1575 UMAC_COMMAND_CONFIG_REG_NO_LGTH_CHECK; 1576 switch (vars->line_speed) { 1577 case SPEED_10: 1578 val |= (0<<2); 1579 break; 1580 case SPEED_100: 1581 val |= (1<<2); 1582 break; 1583 case SPEED_1000: 1584 val |= (2<<2); 1585 break; 1586 case SPEED_2500: 1587 val |= (3<<2); 1588 break; 1589 default: 1590 DP(NETIF_MSG_LINK, "Invalid speed for UMAC %d\n", 1591 vars->line_speed); 1592 break; 1593 } 1594 if (!(vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 1595 val |= UMAC_COMMAND_CONFIG_REG_IGNORE_TX_PAUSE; 1596 1597 if (!(vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)) 1598 val |= UMAC_COMMAND_CONFIG_REG_PAUSE_IGNORE; 1599 1600 if (vars->duplex == DUPLEX_HALF) 1601 val |= UMAC_COMMAND_CONFIG_REG_HD_ENA; 1602 1603 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val); 1604 udelay(50); 1605 1606 /* Configure UMAC for EEE */ 1607 if (vars->eee_status & SHMEM_EEE_ADV_STATUS_MASK) { 1608 DP(NETIF_MSG_LINK, "configured UMAC for EEE\n"); 1609 REG_WR(bp, umac_base + UMAC_REG_UMAC_EEE_CTRL, 1610 UMAC_UMAC_EEE_CTRL_REG_EEE_EN); 1611 REG_WR(bp, umac_base + UMAC_REG_EEE_WAKE_TIMER, 0x11); 1612 } else { 1613 REG_WR(bp, umac_base + UMAC_REG_UMAC_EEE_CTRL, 0x0); 1614 } 1615 1616 /* Set MAC address for source TX Pause/PFC frames (under SW reset) */ 1617 REG_WR(bp, umac_base + UMAC_REG_MAC_ADDR0, 1618 ((params->mac_addr[2] << 24) | 1619 (params->mac_addr[3] << 16) | 1620 (params->mac_addr[4] << 8) | 1621 (params->mac_addr[5]))); 1622 REG_WR(bp, umac_base + UMAC_REG_MAC_ADDR1, 1623 ((params->mac_addr[0] << 8) | 1624 (params->mac_addr[1]))); 1625 1626 /* Enable RX and TX */ 1627 val &= ~UMAC_COMMAND_CONFIG_REG_PAD_EN; 1628 val |= UMAC_COMMAND_CONFIG_REG_TX_ENA | 1629 UMAC_COMMAND_CONFIG_REG_RX_ENA; 1630 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val); 1631 udelay(50); 1632 1633 /* Remove SW Reset */ 1634 val &= ~UMAC_COMMAND_CONFIG_REG_SW_RESET; 1635 1636 /* Check loopback mode */ 1637 if (lb) 1638 val |= UMAC_COMMAND_CONFIG_REG_LOOP_ENA; 1639 REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val); 1640 1641 /* Maximum Frame Length (RW). Defines a 14-Bit maximum frame 1642 * length used by the MAC receive logic to check frames. 1643 */ 1644 REG_WR(bp, umac_base + UMAC_REG_MAXFR, 0x2710); 1645 bnx2x_set_xumac_nig(params, 1646 ((vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) != 0), 1); 1647 vars->mac_type = MAC_TYPE_UMAC; 1648 1649} 1650 1651/* Define the XMAC mode */ 1652static void bnx2x_xmac_init(struct link_params *params, u32 max_speed) 1653{ 1654 struct bnx2x *bp = params->bp; 1655 u32 is_port4mode = bnx2x_is_4_port_mode(bp); 1656 1657 /* In 4-port mode, need to set the mode only once, so if XMAC is 1658 * already out of reset, it means the mode has already been set, 1659 * and it must not* reset the XMAC again, since it controls both 1660 * ports of the path 1661 */ 1662 1663 if (((CHIP_NUM(bp) == CHIP_NUM_57840_4_10) || 1664 (CHIP_NUM(bp) == CHIP_NUM_57840_2_20) || 1665 (CHIP_NUM(bp) == CHIP_NUM_57840_OBSOLETE)) && 1666 is_port4mode && 1667 (REG_RD(bp, MISC_REG_RESET_REG_2) & 1668 MISC_REGISTERS_RESET_REG_2_XMAC)) { 1669 DP(NETIF_MSG_LINK, 1670 "XMAC already out of reset in 4-port mode\n"); 1671 return; 1672 } 1673 1674 /* Hard reset */ 1675 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 1676 MISC_REGISTERS_RESET_REG_2_XMAC); 1677 usleep_range(1000, 2000); 1678 1679 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 1680 MISC_REGISTERS_RESET_REG_2_XMAC); 1681 if (is_port4mode) { 1682 DP(NETIF_MSG_LINK, "Init XMAC to 2 ports x 10G per path\n"); 1683 1684 /* Set the number of ports on the system side to up to 2 */ 1685 REG_WR(bp, MISC_REG_XMAC_CORE_PORT_MODE, 1); 1686 1687 /* Set the number of ports on the Warp Core to 10G */ 1688 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 3); 1689 } else { 1690 /* Set the number of ports on the system side to 1 */ 1691 REG_WR(bp, MISC_REG_XMAC_CORE_PORT_MODE, 0); 1692 if (max_speed == SPEED_10000) { 1693 DP(NETIF_MSG_LINK, 1694 "Init XMAC to 10G x 1 port per path\n"); 1695 /* Set the number of ports on the Warp Core to 10G */ 1696 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 3); 1697 } else { 1698 DP(NETIF_MSG_LINK, 1699 "Init XMAC to 20G x 2 ports per path\n"); 1700 /* Set the number of ports on the Warp Core to 20G */ 1701 REG_WR(bp, MISC_REG_XMAC_PHY_PORT_MODE, 1); 1702 } 1703 } 1704 /* Soft reset */ 1705 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 1706 MISC_REGISTERS_RESET_REG_2_XMAC_SOFT); 1707 usleep_range(1000, 2000); 1708 1709 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 1710 MISC_REGISTERS_RESET_REG_2_XMAC_SOFT); 1711 1712} 1713 1714static void bnx2x_set_xmac_rxtx(struct link_params *params, u8 en) 1715{ 1716 u8 port = params->port; 1717 struct bnx2x *bp = params->bp; 1718 u32 pfc_ctrl, xmac_base = (port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; 1719 u32 val; 1720 1721 if (REG_RD(bp, MISC_REG_RESET_REG_2) & 1722 MISC_REGISTERS_RESET_REG_2_XMAC) { 1723 /* Send an indication to change the state in the NIG back to XON 1724 * Clearing this bit enables the next set of this bit to get 1725 * rising edge 1726 */ 1727 pfc_ctrl = REG_RD(bp, xmac_base + XMAC_REG_PFC_CTRL_HI); 1728 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, 1729 (pfc_ctrl & ~(1<<1))); 1730 REG_WR(bp, xmac_base + XMAC_REG_PFC_CTRL_HI, 1731 (pfc_ctrl | (1<<1))); 1732 DP(NETIF_MSG_LINK, "Disable XMAC on port %x\n", port); 1733 val = REG_RD(bp, xmac_base + XMAC_REG_CTRL); 1734 if (en) 1735 val |= (XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN); 1736 else 1737 val &= ~(XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN); 1738 REG_WR(bp, xmac_base + XMAC_REG_CTRL, val); 1739 } 1740} 1741 1742static int bnx2x_xmac_enable(struct link_params *params, 1743 struct link_vars *vars, u8 lb) 1744{ 1745 u32 val, xmac_base; 1746 struct bnx2x *bp = params->bp; 1747 DP(NETIF_MSG_LINK, "enabling XMAC\n"); 1748 1749 xmac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; 1750 1751 bnx2x_xmac_init(params, vars->line_speed); 1752 1753 /* This register determines on which events the MAC will assert 1754 * error on the i/f to the NIG along w/ EOP. 1755 */ 1756 1757 /* This register tells the NIG whether to send traffic to UMAC 1758 * or XMAC 1759 */ 1760 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 0); 1761 1762 /* When XMAC is in XLGMII mode, disable sending idles for fault 1763 * detection. 1764 */ 1765 if (!(params->phy[INT_PHY].flags & FLAGS_TX_ERROR_CHECK)) { 1766 REG_WR(bp, xmac_base + XMAC_REG_RX_LSS_CTRL, 1767 (XMAC_RX_LSS_CTRL_REG_LOCAL_FAULT_DISABLE | 1768 XMAC_RX_LSS_CTRL_REG_REMOTE_FAULT_DISABLE)); 1769 REG_WR(bp, xmac_base + XMAC_REG_CLEAR_RX_LSS_STATUS, 0); 1770 REG_WR(bp, xmac_base + XMAC_REG_CLEAR_RX_LSS_STATUS, 1771 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_LOCAL_FAULT_STATUS | 1772 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_REMOTE_FAULT_STATUS); 1773 } 1774 /* Set Max packet size */ 1775 REG_WR(bp, xmac_base + XMAC_REG_RX_MAX_SIZE, 0x2710); 1776 1777 /* CRC append for Tx packets */ 1778 REG_WR(bp, xmac_base + XMAC_REG_TX_CTRL, 0xC800); 1779 1780 /* update PFC */ 1781 bnx2x_update_pfc_xmac(params, vars, 0); 1782 1783 if (vars->eee_status & SHMEM_EEE_ADV_STATUS_MASK) { 1784 DP(NETIF_MSG_LINK, "Setting XMAC for EEE\n"); 1785 REG_WR(bp, xmac_base + XMAC_REG_EEE_TIMERS_HI, 0x1380008); 1786 REG_WR(bp, xmac_base + XMAC_REG_EEE_CTRL, 0x1); 1787 } else { 1788 REG_WR(bp, xmac_base + XMAC_REG_EEE_CTRL, 0x0); 1789 } 1790 1791 /* Enable TX and RX */ 1792 val = XMAC_CTRL_REG_TX_EN | XMAC_CTRL_REG_RX_EN; 1793 1794 /* Set MAC in XLGMII mode for dual-mode */ 1795 if ((vars->line_speed == SPEED_20000) && 1796 (params->phy[INT_PHY].supported & 1797 SUPPORTED_20000baseKR2_Full)) 1798 val |= XMAC_CTRL_REG_XLGMII_ALIGN_ENB; 1799 1800 /* Check loopback mode */ 1801 if (lb) 1802 val |= XMAC_CTRL_REG_LINE_LOCAL_LPBK; 1803 REG_WR(bp, xmac_base + XMAC_REG_CTRL, val); 1804 bnx2x_set_xumac_nig(params, 1805 ((vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) != 0), 1); 1806 1807 vars->mac_type = MAC_TYPE_XMAC; 1808 1809 return 0; 1810} 1811 1812static int bnx2x_emac_enable(struct link_params *params, 1813 struct link_vars *vars, u8 lb) 1814{ 1815 struct bnx2x *bp = params->bp; 1816 u8 port = params->port; 1817 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; 1818 u32 val; 1819 1820 DP(NETIF_MSG_LINK, "enabling EMAC\n"); 1821 1822 /* Disable BMAC */ 1823 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 1824 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); 1825 1826 /* enable emac and not bmac */ 1827 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1); 1828 1829 /* ASIC */ 1830 if (vars->phy_flags & PHY_XGXS_FLAG) { 1831 u32 ser_lane = ((params->lane_config & 1832 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> 1833 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); 1834 1835 DP(NETIF_MSG_LINK, "XGXS\n"); 1836 /* select the master lanes (out of 0-3) */ 1837 REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, ser_lane); 1838 /* select XGXS */ 1839 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1); 1840 1841 } else { /* SerDes */ 1842 DP(NETIF_MSG_LINK, "SerDes\n"); 1843 /* select SerDes */ 1844 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0); 1845 } 1846 1847 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE, 1848 EMAC_RX_MODE_RESET); 1849 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, 1850 EMAC_TX_MODE_RESET); 1851 1852 /* pause enable/disable */ 1853 bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE, 1854 EMAC_RX_MODE_FLOW_EN); 1855 1856 bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE, 1857 (EMAC_TX_MODE_EXT_PAUSE_EN | 1858 EMAC_TX_MODE_FLOW_EN)); 1859 if (!(params->feature_config_flags & 1860 FEATURE_CONFIG_PFC_ENABLED)) { 1861 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) 1862 bnx2x_bits_en(bp, emac_base + 1863 EMAC_REG_EMAC_RX_MODE, 1864 EMAC_RX_MODE_FLOW_EN); 1865 1866 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) 1867 bnx2x_bits_en(bp, emac_base + 1868 EMAC_REG_EMAC_TX_MODE, 1869 (EMAC_TX_MODE_EXT_PAUSE_EN | 1870 EMAC_TX_MODE_FLOW_EN)); 1871 } else 1872 bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, 1873 EMAC_TX_MODE_FLOW_EN); 1874 1875 /* KEEP_VLAN_TAG, promiscuous */ 1876 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE); 1877 val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS; 1878 1879 /* Setting this bit causes MAC control frames (except for pause 1880 * frames) to be passed on for processing. This setting has no 1881 * affect on the operation of the pause frames. This bit effects 1882 * all packets regardless of RX Parser packet sorting logic. 1883 * Turn the PFC off to make sure we are in Xon state before 1884 * enabling it. 1885 */ 1886 EMAC_WR(bp, EMAC_REG_RX_PFC_MODE, 0); 1887 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) { 1888 DP(NETIF_MSG_LINK, "PFC is enabled\n"); 1889 /* Enable PFC again */ 1890 EMAC_WR(bp, EMAC_REG_RX_PFC_MODE, 1891 EMAC_REG_RX_PFC_MODE_RX_EN | 1892 EMAC_REG_RX_PFC_MODE_TX_EN | 1893 EMAC_REG_RX_PFC_MODE_PRIORITIES); 1894 1895 EMAC_WR(bp, EMAC_REG_RX_PFC_PARAM, 1896 ((0x0101 << 1897 EMAC_REG_RX_PFC_PARAM_OPCODE_BITSHIFT) | 1898 (0x00ff << 1899 EMAC_REG_RX_PFC_PARAM_PRIORITY_EN_BITSHIFT))); 1900 val |= EMAC_RX_MODE_KEEP_MAC_CONTROL; 1901 } 1902 EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val); 1903 1904 /* Set Loopback */ 1905 val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); 1906 if (lb) 1907 val |= 0x810; 1908 else 1909 val &= ~0x810; 1910 EMAC_WR(bp, EMAC_REG_EMAC_MODE, val); 1911 1912 /* Enable emac */ 1913 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1); 1914 1915 /* Enable emac for jumbo packets */ 1916 EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE, 1917 (EMAC_RX_MTU_SIZE_JUMBO_ENA | 1918 (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD))); 1919 1920 /* Strip CRC */ 1921 REG_WR(bp, NIG_REG_NIG_INGRESS_EMAC0_NO_CRC + port*4, 0x1); 1922 1923 /* Disable the NIG in/out to the bmac */ 1924 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x0); 1925 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, 0x0); 1926 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x0); 1927 1928 /* Enable the NIG in/out to the emac */ 1929 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x1); 1930 val = 0; 1931 if ((params->feature_config_flags & 1932 FEATURE_CONFIG_PFC_ENABLED) || 1933 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 1934 val = 1; 1935 1936 REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val); 1937 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1); 1938 1939 REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0); 1940 1941 vars->mac_type = MAC_TYPE_EMAC; 1942 return 0; 1943} 1944 1945static void bnx2x_update_pfc_bmac1(struct link_params *params, 1946 struct link_vars *vars) 1947{ 1948 u32 wb_data[2]; 1949 struct bnx2x *bp = params->bp; 1950 u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM : 1951 NIG_REG_INGRESS_BMAC0_MEM; 1952 1953 u32 val = 0x14; 1954 if ((!(params->feature_config_flags & 1955 FEATURE_CONFIG_PFC_ENABLED)) && 1956 (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)) 1957 /* Enable BigMAC to react on received Pause packets */ 1958 val |= (1<<5); 1959 wb_data[0] = val; 1960 wb_data[1] = 0; 1961 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_CONTROL, wb_data, 2); 1962 1963 /* TX control */ 1964 val = 0xc0; 1965 if (!(params->feature_config_flags & 1966 FEATURE_CONFIG_PFC_ENABLED) && 1967 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 1968 val |= 0x800000; 1969 wb_data[0] = val; 1970 wb_data[1] = 0; 1971 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_CONTROL, wb_data, 2); 1972} 1973 1974static void bnx2x_update_pfc_bmac2(struct link_params *params, 1975 struct link_vars *vars, 1976 u8 is_lb) 1977{ 1978 /* Set rx control: Strip CRC and enable BigMAC to relay 1979 * control packets to the system as well 1980 */ 1981 u32 wb_data[2]; 1982 struct bnx2x *bp = params->bp; 1983 u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM : 1984 NIG_REG_INGRESS_BMAC0_MEM; 1985 u32 val = 0x14; 1986 1987 if ((!(params->feature_config_flags & 1988 FEATURE_CONFIG_PFC_ENABLED)) && 1989 (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)) 1990 /* Enable BigMAC to react on received Pause packets */ 1991 val |= (1<<5); 1992 wb_data[0] = val; 1993 wb_data[1] = 0; 1994 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, wb_data, 2); 1995 udelay(30); 1996 1997 /* Tx control */ 1998 val = 0xc0; 1999 if (!(params->feature_config_flags & 2000 FEATURE_CONFIG_PFC_ENABLED) && 2001 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 2002 val |= 0x800000; 2003 wb_data[0] = val; 2004 wb_data[1] = 0; 2005 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_CONTROL, wb_data, 2); 2006 2007 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) { 2008 DP(NETIF_MSG_LINK, "PFC is enabled\n"); 2009 /* Enable PFC RX & TX & STATS and set 8 COS */ 2010 wb_data[0] = 0x0; 2011 wb_data[0] |= (1<<0); /* RX */ 2012 wb_data[0] |= (1<<1); /* TX */ 2013 wb_data[0] |= (1<<2); /* Force initial Xon */ 2014 wb_data[0] |= (1<<3); /* 8 cos */ 2015 wb_data[0] |= (1<<5); /* STATS */ 2016 wb_data[1] = 0; 2017 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL, 2018 wb_data, 2); 2019 /* Clear the force Xon */ 2020 wb_data[0] &= ~(1<<2); 2021 } else { 2022 DP(NETIF_MSG_LINK, "PFC is disabled\n"); 2023 /* Disable PFC RX & TX & STATS and set 8 COS */ 2024 wb_data[0] = 0x8; 2025 wb_data[1] = 0; 2026 } 2027 2028 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL, wb_data, 2); 2029 2030 /* Set Time (based unit is 512 bit time) between automatic 2031 * re-sending of PP packets amd enable automatic re-send of 2032 * Per-Priroity Packet as long as pp_gen is asserted and 2033 * pp_disable is low. 2034 */ 2035 val = 0x8000; 2036 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) 2037 val |= (1<<16); /* enable automatic re-send */ 2038 2039 wb_data[0] = val; 2040 wb_data[1] = 0; 2041 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL, 2042 wb_data, 2); 2043 2044 /* mac control */ 2045 val = 0x3; /* Enable RX and TX */ 2046 if (is_lb) { 2047 val |= 0x4; /* Local loopback */ 2048 DP(NETIF_MSG_LINK, "enable bmac loopback\n"); 2049 } 2050 /* When PFC enabled, Pass pause frames towards the NIG. */ 2051 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) 2052 val |= ((1<<6)|(1<<5)); 2053 2054 wb_data[0] = val; 2055 wb_data[1] = 0; 2056 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2); 2057} 2058 2059/****************************************************************************** 2060* Description: 2061* This function is needed because NIG ARB_CREDIT_WEIGHT_X are 2062* not continues and ARB_CREDIT_WEIGHT_0 + offset is suitable. 2063******************************************************************************/ 2064static int bnx2x_pfc_nig_rx_priority_mask(struct bnx2x *bp, 2065 u8 cos_entry, 2066 u32 priority_mask, u8 port) 2067{ 2068 u32 nig_reg_rx_priority_mask_add = 0; 2069 2070 switch (cos_entry) { 2071 case 0: 2072 nig_reg_rx_priority_mask_add = (port) ? 2073 NIG_REG_P1_RX_COS0_PRIORITY_MASK : 2074 NIG_REG_P0_RX_COS0_PRIORITY_MASK; 2075 break; 2076 case 1: 2077 nig_reg_rx_priority_mask_add = (port) ? 2078 NIG_REG_P1_RX_COS1_PRIORITY_MASK : 2079 NIG_REG_P0_RX_COS1_PRIORITY_MASK; 2080 break; 2081 case 2: 2082 nig_reg_rx_priority_mask_add = (port) ? 2083 NIG_REG_P1_RX_COS2_PRIORITY_MASK : 2084 NIG_REG_P0_RX_COS2_PRIORITY_MASK; 2085 break; 2086 case 3: 2087 if (port) 2088 return -EINVAL; 2089 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS3_PRIORITY_MASK; 2090 break; 2091 case 4: 2092 if (port) 2093 return -EINVAL; 2094 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS4_PRIORITY_MASK; 2095 break; 2096 case 5: 2097 if (port) 2098 return -EINVAL; 2099 nig_reg_rx_priority_mask_add = NIG_REG_P0_RX_COS5_PRIORITY_MASK; 2100 break; 2101 } 2102 2103 REG_WR(bp, nig_reg_rx_priority_mask_add, priority_mask); 2104 2105 return 0; 2106} 2107static void bnx2x_update_mng(struct link_params *params, u32 link_status) 2108{ 2109 struct bnx2x *bp = params->bp; 2110 2111 REG_WR(bp, params->shmem_base + 2112 offsetof(struct shmem_region, 2113 port_mb[params->port].link_status), link_status); 2114} 2115 2116static void bnx2x_update_link_attr(struct link_params *params, u32 link_attr) 2117{ 2118 struct bnx2x *bp = params->bp; 2119 2120 if (SHMEM2_HAS(bp, link_attr_sync)) 2121 REG_WR(bp, params->shmem2_base + 2122 offsetof(struct shmem2_region, 2123 link_attr_sync[params->port]), link_attr); 2124} 2125 2126static void bnx2x_update_pfc_nig(struct link_params *params, 2127 struct link_vars *vars, 2128 struct bnx2x_nig_brb_pfc_port_params *nig_params) 2129{ 2130 u32 xcm_mask = 0, ppp_enable = 0, pause_enable = 0, llfc_out_en = 0; 2131 u32 llfc_enable = 0, xcm_out_en = 0, hwpfc_enable = 0; 2132 u32 pkt_priority_to_cos = 0; 2133 struct bnx2x *bp = params->bp; 2134 u8 port = params->port; 2135 2136 int set_pfc = params->feature_config_flags & 2137 FEATURE_CONFIG_PFC_ENABLED; 2138 DP(NETIF_MSG_LINK, "updating pfc nig parameters\n"); 2139 2140 /* When NIG_LLH0_XCM_MASK_REG_LLHX_XCM_MASK_BCN bit is set 2141 * MAC control frames (that are not pause packets) 2142 * will be forwarded to the XCM. 2143 */ 2144 xcm_mask = REG_RD(bp, port ? NIG_REG_LLH1_XCM_MASK : 2145 NIG_REG_LLH0_XCM_MASK); 2146 /* NIG params will override non PFC params, since it's possible to 2147 * do transition from PFC to SAFC 2148 */ 2149 if (set_pfc) { 2150 pause_enable = 0; 2151 llfc_out_en = 0; 2152 llfc_enable = 0; 2153 if (CHIP_IS_E3(bp)) 2154 ppp_enable = 0; 2155 else 2156 ppp_enable = 1; 2157 xcm_mask &= ~(port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN : 2158 NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN); 2159 xcm_out_en = 0; 2160 hwpfc_enable = 1; 2161 } else { 2162 if (nig_params) { 2163 llfc_out_en = nig_params->llfc_out_en; 2164 llfc_enable = nig_params->llfc_enable; 2165 pause_enable = nig_params->pause_enable; 2166 } else /* Default non PFC mode - PAUSE */ 2167 pause_enable = 1; 2168 2169 xcm_mask |= (port ? NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN : 2170 NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN); 2171 xcm_out_en = 1; 2172 } 2173 2174 if (CHIP_IS_E3(bp)) 2175 REG_WR(bp, port ? NIG_REG_BRB1_PAUSE_IN_EN : 2176 NIG_REG_BRB0_PAUSE_IN_EN, pause_enable); 2177 REG_WR(bp, port ? NIG_REG_LLFC_OUT_EN_1 : 2178 NIG_REG_LLFC_OUT_EN_0, llfc_out_en); 2179 REG_WR(bp, port ? NIG_REG_LLFC_ENABLE_1 : 2180 NIG_REG_LLFC_ENABLE_0, llfc_enable); 2181 REG_WR(bp, port ? NIG_REG_PAUSE_ENABLE_1 : 2182 NIG_REG_PAUSE_ENABLE_0, pause_enable); 2183 2184 REG_WR(bp, port ? NIG_REG_PPP_ENABLE_1 : 2185 NIG_REG_PPP_ENABLE_0, ppp_enable); 2186 2187 REG_WR(bp, port ? NIG_REG_LLH1_XCM_MASK : 2188 NIG_REG_LLH0_XCM_MASK, xcm_mask); 2189 2190 REG_WR(bp, port ? NIG_REG_LLFC_EGRESS_SRC_ENABLE_1 : 2191 NIG_REG_LLFC_EGRESS_SRC_ENABLE_0, 0x7); 2192 2193 /* Output enable for RX_XCM # IF */ 2194 REG_WR(bp, port ? NIG_REG_XCM1_OUT_EN : 2195 NIG_REG_XCM0_OUT_EN, xcm_out_en); 2196 2197 /* HW PFC TX enable */ 2198 REG_WR(bp, port ? NIG_REG_P1_HWPFC_ENABLE : 2199 NIG_REG_P0_HWPFC_ENABLE, hwpfc_enable); 2200 2201 if (nig_params) { 2202 u8 i = 0; 2203 pkt_priority_to_cos = nig_params->pkt_priority_to_cos; 2204 2205 for (i = 0; i < nig_params->num_of_rx_cos_priority_mask; i++) 2206 bnx2x_pfc_nig_rx_priority_mask(bp, i, 2207 nig_params->rx_cos_priority_mask[i], port); 2208 2209 REG_WR(bp, port ? NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_1 : 2210 NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0, 2211 nig_params->llfc_high_priority_classes); 2212 2213 REG_WR(bp, port ? NIG_REG_LLFC_LOW_PRIORITY_CLASSES_1 : 2214 NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0, 2215 nig_params->llfc_low_priority_classes); 2216 } 2217 REG_WR(bp, port ? NIG_REG_P1_PKT_PRIORITY_TO_COS : 2218 NIG_REG_P0_PKT_PRIORITY_TO_COS, 2219 pkt_priority_to_cos); 2220} 2221 2222int bnx2x_update_pfc(struct link_params *params, 2223 struct link_vars *vars, 2224 struct bnx2x_nig_brb_pfc_port_params *pfc_params) 2225{ 2226 /* The PFC and pause are orthogonal to one another, meaning when 2227 * PFC is enabled, the pause are disabled, and when PFC is 2228 * disabled, pause are set according to the pause result. 2229 */ 2230 u32 val; 2231 struct bnx2x *bp = params->bp; 2232 u8 bmac_loopback = (params->loopback_mode == LOOPBACK_BMAC); 2233 2234 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) 2235 vars->link_status |= LINK_STATUS_PFC_ENABLED; 2236 else 2237 vars->link_status &= ~LINK_STATUS_PFC_ENABLED; 2238 2239 bnx2x_update_mng(params, vars->link_status); 2240 2241 /* Update NIG params */ 2242 bnx2x_update_pfc_nig(params, vars, pfc_params); 2243 2244 if (!vars->link_up) 2245 return 0; 2246 2247 DP(NETIF_MSG_LINK, "About to update PFC in BMAC\n"); 2248 2249 if (CHIP_IS_E3(bp)) { 2250 if (vars->mac_type == MAC_TYPE_XMAC) 2251 bnx2x_update_pfc_xmac(params, vars, 0); 2252 } else { 2253 val = REG_RD(bp, MISC_REG_RESET_REG_2); 2254 if ((val & 2255 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port)) 2256 == 0) { 2257 DP(NETIF_MSG_LINK, "About to update PFC in EMAC\n"); 2258 bnx2x_emac_enable(params, vars, 0); 2259 return 0; 2260 } 2261 if (CHIP_IS_E2(bp)) 2262 bnx2x_update_pfc_bmac2(params, vars, bmac_loopback); 2263 else 2264 bnx2x_update_pfc_bmac1(params, vars); 2265 2266 val = 0; 2267 if ((params->feature_config_flags & 2268 FEATURE_CONFIG_PFC_ENABLED) || 2269 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 2270 val = 1; 2271 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + params->port*4, val); 2272 } 2273 return 0; 2274} 2275 2276static int bnx2x_bmac1_enable(struct link_params *params, 2277 struct link_vars *vars, 2278 u8 is_lb) 2279{ 2280 struct bnx2x *bp = params->bp; 2281 u8 port = params->port; 2282 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : 2283 NIG_REG_INGRESS_BMAC0_MEM; 2284 u32 wb_data[2]; 2285 u32 val; 2286 2287 DP(NETIF_MSG_LINK, "Enabling BigMAC1\n"); 2288 2289 /* XGXS control */ 2290 wb_data[0] = 0x3c; 2291 wb_data[1] = 0; 2292 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL, 2293 wb_data, 2); 2294 2295 /* TX MAC SA */ 2296 wb_data[0] = ((params->mac_addr[2] << 24) | 2297 (params->mac_addr[3] << 16) | 2298 (params->mac_addr[4] << 8) | 2299 params->mac_addr[5]); 2300 wb_data[1] = ((params->mac_addr[0] << 8) | 2301 params->mac_addr[1]); 2302 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2); 2303 2304 /* MAC control */ 2305 val = 0x3; 2306 if (is_lb) { 2307 val |= 0x4; 2308 DP(NETIF_MSG_LINK, "enable bmac loopback\n"); 2309 } 2310 wb_data[0] = val; 2311 wb_data[1] = 0; 2312 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2); 2313 2314 /* Set rx mtu */ 2315 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; 2316 wb_data[1] = 0; 2317 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2); 2318 2319 bnx2x_update_pfc_bmac1(params, vars); 2320 2321 /* Set tx mtu */ 2322 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; 2323 wb_data[1] = 0; 2324 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2); 2325 2326 /* Set cnt max size */ 2327 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; 2328 wb_data[1] = 0; 2329 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2); 2330 2331 /* Configure SAFC */ 2332 wb_data[0] = 0x1000200; 2333 wb_data[1] = 0; 2334 REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS, 2335 wb_data, 2); 2336 2337 return 0; 2338} 2339 2340static int bnx2x_bmac2_enable(struct link_params *params, 2341 struct link_vars *vars, 2342 u8 is_lb) 2343{ 2344 struct bnx2x *bp = params->bp; 2345 u8 port = params->port; 2346 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : 2347 NIG_REG_INGRESS_BMAC0_MEM; 2348 u32 wb_data[2]; 2349 2350 DP(NETIF_MSG_LINK, "Enabling BigMAC2\n"); 2351 2352 wb_data[0] = 0; 2353 wb_data[1] = 0; 2354 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2); 2355 udelay(30); 2356 2357 /* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */ 2358 wb_data[0] = 0x3c; 2359 wb_data[1] = 0; 2360 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_XGXS_CONTROL, 2361 wb_data, 2); 2362 2363 udelay(30); 2364 2365 /* TX MAC SA */ 2366 wb_data[0] = ((params->mac_addr[2] << 24) | 2367 (params->mac_addr[3] << 16) | 2368 (params->mac_addr[4] << 8) | 2369 params->mac_addr[5]); 2370 wb_data[1] = ((params->mac_addr[0] << 8) | 2371 params->mac_addr[1]); 2372 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR, 2373 wb_data, 2); 2374 2375 udelay(30); 2376 2377 /* Configure SAFC */ 2378 wb_data[0] = 0x1000200; 2379 wb_data[1] = 0; 2380 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS, 2381 wb_data, 2); 2382 udelay(30); 2383 2384 /* Set RX MTU */ 2385 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; 2386 wb_data[1] = 0; 2387 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2); 2388 udelay(30); 2389 2390 /* Set TX MTU */ 2391 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; 2392 wb_data[1] = 0; 2393 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2); 2394 udelay(30); 2395 /* Set cnt max size */ 2396 wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2; 2397 wb_data[1] = 0; 2398 REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2); 2399 udelay(30); 2400 bnx2x_update_pfc_bmac2(params, vars, is_lb); 2401 2402 return 0; 2403} 2404 2405static int bnx2x_bmac_enable(struct link_params *params, 2406 struct link_vars *vars, 2407 u8 is_lb, u8 reset_bmac) 2408{ 2409 int rc = 0; 2410 u8 port = params->port; 2411 struct bnx2x *bp = params->bp; 2412 u32 val; 2413 /* Reset and unreset the BigMac */ 2414 if (reset_bmac) { 2415 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 2416 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); 2417 usleep_range(1000, 2000); 2418 } 2419 2420 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 2421 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); 2422 2423 /* Enable access for bmac registers */ 2424 REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1); 2425 2426 /* Enable BMAC according to BMAC type*/ 2427 if (CHIP_IS_E2(bp)) 2428 rc = bnx2x_bmac2_enable(params, vars, is_lb); 2429 else 2430 rc = bnx2x_bmac1_enable(params, vars, is_lb); 2431 REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1); 2432 REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0); 2433 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0); 2434 val = 0; 2435 if ((params->feature_config_flags & 2436 FEATURE_CONFIG_PFC_ENABLED) || 2437 (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)) 2438 val = 1; 2439 REG_WR(bp, NIG_REG_BMAC0_PAUSE_OUT_EN + port*4, val); 2440 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x0); 2441 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0x0); 2442 REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, 0x0); 2443 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0x1); 2444 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1); 2445 2446 vars->mac_type = MAC_TYPE_BMAC; 2447 return rc; 2448} 2449 2450static void bnx2x_set_bmac_rx(struct bnx2x *bp, u32 chip_id, u8 port, u8 en) 2451{ 2452 u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : 2453 NIG_REG_INGRESS_BMAC0_MEM; 2454 u32 wb_data[2]; 2455 u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); 2456 2457 if (CHIP_IS_E2(bp)) 2458 bmac_addr += BIGMAC2_REGISTER_BMAC_CONTROL; 2459 else 2460 bmac_addr += BIGMAC_REGISTER_BMAC_CONTROL; 2461 /* Only if the bmac is out of reset */ 2462 if (REG_RD(bp, MISC_REG_RESET_REG_2) & 2463 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) && 2464 nig_bmac_enable) { 2465 /* Clear Rx Enable bit in BMAC_CONTROL register */ 2466 REG_RD_DMAE(bp, bmac_addr, wb_data, 2); 2467 if (en) 2468 wb_data[0] |= BMAC_CONTROL_RX_ENABLE; 2469 else 2470 wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; 2471 REG_WR_DMAE(bp, bmac_addr, wb_data, 2); 2472 usleep_range(1000, 2000); 2473 } 2474} 2475 2476static int bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, 2477 u32 line_speed) 2478{ 2479 struct bnx2x *bp = params->bp; 2480 u8 port = params->port; 2481 u32 init_crd, crd; 2482 u32 count = 1000; 2483 2484 /* Disable port */ 2485 REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1); 2486 2487 /* Wait for init credit */ 2488 init_crd = REG_RD(bp, PBF_REG_P0_INIT_CRD + port*4); 2489 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); 2490 DP(NETIF_MSG_LINK, "init_crd 0x%x crd 0x%x\n", init_crd, crd); 2491 2492 while ((init_crd != crd) && count) { 2493 usleep_range(5000, 10000); 2494 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); 2495 count--; 2496 } 2497 crd = REG_RD(bp, PBF_REG_P0_CREDIT + port*8); 2498 if (init_crd != crd) { 2499 DP(NETIF_MSG_LINK, "BUG! init_crd 0x%x != crd 0x%x\n", 2500 init_crd, crd); 2501 return -EINVAL; 2502 } 2503 2504 if (flow_ctrl & BNX2X_FLOW_CTRL_RX || 2505 line_speed == SPEED_10 || 2506 line_speed == SPEED_100 || 2507 line_speed == SPEED_1000 || 2508 line_speed == SPEED_2500) { 2509 REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1); 2510 /* Update threshold */ 2511 REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); 2512 /* Update init credit */ 2513 init_crd = 778; /* (800-18-4) */ 2514 2515 } else { 2516 u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + 2517 ETH_OVREHEAD)/16; 2518 REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); 2519 /* Update threshold */ 2520 REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh); 2521 /* Update init credit */ 2522 switch (line_speed) { 2523 case SPEED_10000: 2524 init_crd = thresh + 553 - 22; 2525 break; 2526 default: 2527 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", 2528 line_speed); 2529 return -EINVAL; 2530 } 2531 } 2532 REG_WR(bp, PBF_REG_P0_INIT_CRD + port*4, init_crd); 2533 DP(NETIF_MSG_LINK, "PBF updated to speed %d credit %d\n", 2534 line_speed, init_crd); 2535 2536 /* Probe the credit changes */ 2537 REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x1); 2538 usleep_range(5000, 10000); 2539 REG_WR(bp, PBF_REG_INIT_P0 + port*4, 0x0); 2540 2541 /* Enable port */ 2542 REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x0); 2543 return 0; 2544} 2545 2546/** 2547 * bnx2x_get_emac_base - retrive emac base address 2548 * 2549 * @bp: driver handle 2550 * @mdc_mdio_access: access type 2551 * @port: port id 2552 * 2553 * This function selects the MDC/MDIO access (through emac0 or 2554 * emac1) depend on the mdc_mdio_access, port, port swapped. Each 2555 * phy has a default access mode, which could also be overridden 2556 * by nvram configuration. This parameter, whether this is the 2557 * default phy configuration, or the nvram overrun 2558 * configuration, is passed here as mdc_mdio_access and selects 2559 * the emac_base for the CL45 read/writes operations 2560 */ 2561static u32 bnx2x_get_emac_base(struct bnx2x *bp, 2562 u32 mdc_mdio_access, u8 port) 2563{ 2564 u32 emac_base = 0; 2565 switch (mdc_mdio_access) { 2566 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_PHY_TYPE: 2567 break; 2568 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC0: 2569 if (REG_RD(bp, NIG_REG_PORT_SWAP)) 2570 emac_base = GRCBASE_EMAC1; 2571 else 2572 emac_base = GRCBASE_EMAC0; 2573 break; 2574 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1: 2575 if (REG_RD(bp, NIG_REG_PORT_SWAP)) 2576 emac_base = GRCBASE_EMAC0; 2577 else 2578 emac_base = GRCBASE_EMAC1; 2579 break; 2580 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH: 2581 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; 2582 break; 2583 case SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED: 2584 emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1; 2585 break; 2586 default: 2587 break; 2588 } 2589 return emac_base; 2590 2591} 2592 2593/******************************************************************/ 2594/* CL22 access functions */ 2595/******************************************************************/ 2596static int bnx2x_cl22_write(struct bnx2x *bp, 2597 struct bnx2x_phy *phy, 2598 u16 reg, u16 val) 2599{ 2600 u32 tmp, mode; 2601 u8 i; 2602 int rc = 0; 2603 /* Switch to CL22 */ 2604 mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); 2605 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, 2606 mode & ~EMAC_MDIO_MODE_CLAUSE_45); 2607 2608 /* Address */ 2609 tmp = ((phy->addr << 21) | (reg << 16) | val | 2610 EMAC_MDIO_COMM_COMMAND_WRITE_22 | 2611 EMAC_MDIO_COMM_START_BUSY); 2612 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp); 2613 2614 for (i = 0; i < 50; i++) { 2615 udelay(10); 2616 2617 tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); 2618 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { 2619 udelay(5); 2620 break; 2621 } 2622 } 2623 if (tmp & EMAC_MDIO_COMM_START_BUSY) { 2624 DP(NETIF_MSG_LINK, "write phy register failed\n"); 2625 rc = -EFAULT; 2626 } 2627 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, mode); 2628 return rc; 2629} 2630 2631static int bnx2x_cl22_read(struct bnx2x *bp, 2632 struct bnx2x_phy *phy, 2633 u16 reg, u16 *ret_val) 2634{ 2635 u32 val, mode; 2636 u16 i; 2637 int rc = 0; 2638 2639 /* Switch to CL22 */ 2640 mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); 2641 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, 2642 mode & ~EMAC_MDIO_MODE_CLAUSE_45); 2643 2644 /* Address */ 2645 val = ((phy->addr << 21) | (reg << 16) | 2646 EMAC_MDIO_COMM_COMMAND_READ_22 | 2647 EMAC_MDIO_COMM_START_BUSY); 2648 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val); 2649 2650 for (i = 0; i < 50; i++) { 2651 udelay(10); 2652 2653 val = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); 2654 if (!(val & EMAC_MDIO_COMM_START_BUSY)) { 2655 *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA); 2656 udelay(5); 2657 break; 2658 } 2659 } 2660 if (val & EMAC_MDIO_COMM_START_BUSY) { 2661 DP(NETIF_MSG_LINK, "read phy register failed\n"); 2662 2663 *ret_val = 0; 2664 rc = -EFAULT; 2665 } 2666 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, mode); 2667 return rc; 2668} 2669 2670/******************************************************************/ 2671/* CL45 access functions */ 2672/******************************************************************/ 2673static int bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, 2674 u8 devad, u16 reg, u16 *ret_val) 2675{ 2676 u32 val; 2677 u16 i; 2678 int rc = 0; 2679 u32 chip_id; 2680 if (phy->flags & FLAGS_MDC_MDIO_WA_G) { 2681 chip_id = (REG_RD(bp, MISC_REG_CHIP_NUM) << 16) | 2682 ((REG_RD(bp, MISC_REG_CHIP_REV) & 0xf) << 12); 2683 bnx2x_set_mdio_clk(bp, chip_id, phy->mdio_ctrl); 2684 } 2685 2686 if (phy->flags & FLAGS_MDC_MDIO_WA_B0) 2687 bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS, 2688 EMAC_MDIO_STATUS_10MB); 2689 /* Address */ 2690 val = ((phy->addr << 21) | (devad << 16) | reg | 2691 EMAC_MDIO_COMM_COMMAND_ADDRESS | 2692 EMAC_MDIO_COMM_START_BUSY); 2693 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val); 2694 2695 for (i = 0; i < 50; i++) { 2696 udelay(10); 2697 2698 val = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); 2699 if (!(val & EMAC_MDIO_COMM_START_BUSY)) { 2700 udelay(5); 2701 break; 2702 } 2703 } 2704 if (val & EMAC_MDIO_COMM_START_BUSY) { 2705 DP(NETIF_MSG_LINK, "read phy register failed\n"); 2706 netdev_err(bp->dev, "MDC/MDIO access timeout\n"); 2707 *ret_val = 0; 2708 rc = -EFAULT; 2709 } else { 2710 /* Data */ 2711 val = ((phy->addr << 21) | (devad << 16) | 2712 EMAC_MDIO_COMM_COMMAND_READ_45 | 2713 EMAC_MDIO_COMM_START_BUSY); 2714 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, val); 2715 2716 for (i = 0; i < 50; i++) { 2717 udelay(10); 2718 2719 val = REG_RD(bp, phy->mdio_ctrl + 2720 EMAC_REG_EMAC_MDIO_COMM); 2721 if (!(val & EMAC_MDIO_COMM_START_BUSY)) { 2722 *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA); 2723 break; 2724 } 2725 } 2726 if (val & EMAC_MDIO_COMM_START_BUSY) { 2727 DP(NETIF_MSG_LINK, "read phy register failed\n"); 2728 netdev_err(bp->dev, "MDC/MDIO access timeout\n"); 2729 *ret_val = 0; 2730 rc = -EFAULT; 2731 } 2732 } 2733 /* Work around for E3 A0 */ 2734 if (phy->flags & FLAGS_MDC_MDIO_WA) { 2735 phy->flags ^= FLAGS_DUMMY_READ; 2736 if (phy->flags & FLAGS_DUMMY_READ) { 2737 u16 temp_val; 2738 bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val); 2739 } 2740 } 2741 2742 if (phy->flags & FLAGS_MDC_MDIO_WA_B0) 2743 bnx2x_bits_dis(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS, 2744 EMAC_MDIO_STATUS_10MB); 2745 return rc; 2746} 2747 2748static int bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, 2749 u8 devad, u16 reg, u16 val) 2750{ 2751 u32 tmp; 2752 u8 i; 2753 int rc = 0; 2754 u32 chip_id; 2755 if (phy->flags & FLAGS_MDC_MDIO_WA_G) { 2756 chip_id = (REG_RD(bp, MISC_REG_CHIP_NUM) << 16) | 2757 ((REG_RD(bp, MISC_REG_CHIP_REV) & 0xf) << 12); 2758 bnx2x_set_mdio_clk(bp, chip_id, phy->mdio_ctrl); 2759 } 2760 2761 if (phy->flags & FLAGS_MDC_MDIO_WA_B0) 2762 bnx2x_bits_en(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS, 2763 EMAC_MDIO_STATUS_10MB); 2764 2765 /* Address */ 2766 tmp = ((phy->addr << 21) | (devad << 16) | reg | 2767 EMAC_MDIO_COMM_COMMAND_ADDRESS | 2768 EMAC_MDIO_COMM_START_BUSY); 2769 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp); 2770 2771 for (i = 0; i < 50; i++) { 2772 udelay(10); 2773 2774 tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); 2775 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { 2776 udelay(5); 2777 break; 2778 } 2779 } 2780 if (tmp & EMAC_MDIO_COMM_START_BUSY) { 2781 DP(NETIF_MSG_LINK, "write phy register failed\n"); 2782 netdev_err(bp->dev, "MDC/MDIO access timeout\n"); 2783 rc = -EFAULT; 2784 } else { 2785 /* Data */ 2786 tmp = ((phy->addr << 21) | (devad << 16) | val | 2787 EMAC_MDIO_COMM_COMMAND_WRITE_45 | 2788 EMAC_MDIO_COMM_START_BUSY); 2789 REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM, tmp); 2790 2791 for (i = 0; i < 50; i++) { 2792 udelay(10); 2793 2794 tmp = REG_RD(bp, phy->mdio_ctrl + 2795 EMAC_REG_EMAC_MDIO_COMM); 2796 if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { 2797 udelay(5); 2798 break; 2799 } 2800 } 2801 if (tmp & EMAC_MDIO_COMM_START_BUSY) { 2802 DP(NETIF_MSG_LINK, "write phy register failed\n"); 2803 netdev_err(bp->dev, "MDC/MDIO access timeout\n"); 2804 rc = -EFAULT; 2805 } 2806 } 2807 /* Work around for E3 A0 */ 2808 if (phy->flags & FLAGS_MDC_MDIO_WA) { 2809 phy->flags ^= FLAGS_DUMMY_READ; 2810 if (phy->flags & FLAGS_DUMMY_READ) { 2811 u16 temp_val; 2812 bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val); 2813 } 2814 } 2815 if (phy->flags & FLAGS_MDC_MDIO_WA_B0) 2816 bnx2x_bits_dis(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_STATUS, 2817 EMAC_MDIO_STATUS_10MB); 2818 return rc; 2819} 2820 2821/******************************************************************/ 2822/* EEE section */ 2823/******************************************************************/ 2824static u8 bnx2x_eee_has_cap(struct link_params *params) 2825{ 2826 struct bnx2x *bp = params->bp; 2827 2828 if (REG_RD(bp, params->shmem2_base) <= 2829 offsetof(struct shmem2_region, eee_status[params->port])) 2830 return 0; 2831 2832 return 1; 2833} 2834 2835static int bnx2x_eee_nvram_to_time(u32 nvram_mode, u32 *idle_timer) 2836{ 2837 switch (nvram_mode) { 2838 case PORT_FEAT_CFG_EEE_POWER_MODE_BALANCED: 2839 *idle_timer = EEE_MODE_NVRAM_BALANCED_TIME; 2840 break; 2841 case PORT_FEAT_CFG_EEE_POWER_MODE_AGGRESSIVE: 2842 *idle_timer = EEE_MODE_NVRAM_AGGRESSIVE_TIME; 2843 break; 2844 case PORT_FEAT_CFG_EEE_POWER_MODE_LOW_LATENCY: 2845 *idle_timer = EEE_MODE_NVRAM_LATENCY_TIME; 2846 break; 2847 default: 2848 *idle_timer = 0; 2849 break; 2850 } 2851 2852 return 0; 2853} 2854 2855static int bnx2x_eee_time_to_nvram(u32 idle_timer, u32 *nvram_mode) 2856{ 2857 switch (idle_timer) { 2858 case EEE_MODE_NVRAM_BALANCED_TIME: 2859 *nvram_mode = PORT_FEAT_CFG_EEE_POWER_MODE_BALANCED; 2860 break; 2861 case EEE_MODE_NVRAM_AGGRESSIVE_TIME: 2862 *nvram_mode = PORT_FEAT_CFG_EEE_POWER_MODE_AGGRESSIVE; 2863 break; 2864 case EEE_MODE_NVRAM_LATENCY_TIME: 2865 *nvram_mode = PORT_FEAT_CFG_EEE_POWER_MODE_LOW_LATENCY; 2866 break; 2867 default: 2868 *nvram_mode = PORT_FEAT_CFG_EEE_POWER_MODE_DISABLED; 2869 break; 2870 } 2871 2872 return 0; 2873} 2874 2875static u32 bnx2x_eee_calc_timer(struct link_params *params) 2876{ 2877 u32 eee_mode, eee_idle; 2878 struct bnx2x *bp = params->bp; 2879 2880 if (params->eee_mode & EEE_MODE_OVERRIDE_NVRAM) { 2881 if (params->eee_mode & EEE_MODE_OUTPUT_TIME) { 2882 /* time value in eee_mode --> used directly*/ 2883 eee_idle = params->eee_mode & EEE_MODE_TIMER_MASK; 2884 } else { 2885 /* hsi value in eee_mode --> time */ 2886 if (bnx2x_eee_nvram_to_time(params->eee_mode & 2887 EEE_MODE_NVRAM_MASK, 2888 &eee_idle)) 2889 return 0; 2890 } 2891 } else { 2892 /* hsi values in nvram --> time*/ 2893 eee_mode = ((REG_RD(bp, params->shmem_base + 2894 offsetof(struct shmem_region, dev_info. 2895 port_feature_config[params->port]. 2896 eee_power_mode)) & 2897 PORT_FEAT_CFG_EEE_POWER_MODE_MASK) >> 2898 PORT_FEAT_CFG_EEE_POWER_MODE_SHIFT); 2899 2900 if (bnx2x_eee_nvram_to_time(eee_mode, &eee_idle)) 2901 return 0; 2902 } 2903 2904 return eee_idle; 2905} 2906 2907static int bnx2x_eee_set_timers(struct link_params *params, 2908 struct link_vars *vars) 2909{ 2910 u32 eee_idle = 0, eee_mode; 2911 struct bnx2x *bp = params->bp; 2912 2913 eee_idle = bnx2x_eee_calc_timer(params); 2914 2915 if (eee_idle) { 2916 REG_WR(bp, MISC_REG_CPMU_LP_IDLE_THR_P0 + (params->port << 2), 2917 eee_idle); 2918 } else if ((params->eee_mode & EEE_MODE_ENABLE_LPI) && 2919 (params->eee_mode & EEE_MODE_OVERRIDE_NVRAM) && 2920 (params->eee_mode & EEE_MODE_OUTPUT_TIME)) { 2921 DP(NETIF_MSG_LINK, "Error: Tx LPI is enabled with timer 0\n"); 2922 return -EINVAL; 2923 } 2924 2925 vars->eee_status &= ~(SHMEM_EEE_TIMER_MASK | SHMEM_EEE_TIME_OUTPUT_BIT); 2926 if (params->eee_mode & EEE_MODE_OUTPUT_TIME) { 2927 /* eee_idle in 1u --> eee_status in 16u */ 2928 eee_idle >>= 4; 2929 vars->eee_status |= (eee_idle & SHMEM_EEE_TIMER_MASK) | 2930 SHMEM_EEE_TIME_OUTPUT_BIT; 2931 } else { 2932 if (bnx2x_eee_time_to_nvram(eee_idle, &eee_mode)) 2933 return -EINVAL; 2934 vars->eee_status |= eee_mode; 2935 } 2936 2937 return 0; 2938} 2939 2940static int bnx2x_eee_initial_config(struct link_params *params, 2941 struct link_vars *vars, u8 mode) 2942{ 2943 vars->eee_status |= ((u32) mode) << SHMEM_EEE_SUPPORTED_SHIFT; 2944 2945 /* Propagate params' bits --> vars (for migration exposure) */ 2946 if (params->eee_mode & EEE_MODE_ENABLE_LPI) 2947 vars->eee_status |= SHMEM_EEE_LPI_REQUESTED_BIT; 2948 else 2949 vars->eee_status &= ~SHMEM_EEE_LPI_REQUESTED_BIT; 2950 2951 if (params->eee_mode & EEE_MODE_ADV_LPI) 2952 vars->eee_status |= SHMEM_EEE_REQUESTED_BIT; 2953 else 2954 vars->eee_status &= ~SHMEM_EEE_REQUESTED_BIT; 2955 2956 return bnx2x_eee_set_timers(params, vars); 2957} 2958 2959static int bnx2x_eee_disable(struct bnx2x_phy *phy, 2960 struct link_params *params, 2961 struct link_vars *vars) 2962{ 2963 struct bnx2x *bp = params->bp; 2964 2965 /* Make Certain LPI is disabled */ 2966 REG_WR(bp, MISC_REG_CPMU_LP_FW_ENABLE_P0 + (params->port << 2), 0); 2967 2968 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_EEE_ADV, 0x0); 2969 2970 vars->eee_status &= ~SHMEM_EEE_ADV_STATUS_MASK; 2971 2972 return 0; 2973} 2974 2975static int bnx2x_eee_advertise(struct bnx2x_phy *phy, 2976 struct link_params *params, 2977 struct link_vars *vars, u8 modes) 2978{ 2979 struct bnx2x *bp = params->bp; 2980 u16 val = 0; 2981 2982 /* Mask events preventing LPI generation */ 2983 REG_WR(bp, MISC_REG_CPMU_LP_MASK_EXT_P0 + (params->port << 2), 0xfc20); 2984 2985 if (modes & SHMEM_EEE_10G_ADV) { 2986 DP(NETIF_MSG_LINK, "Advertise 10GBase-T EEE\n"); 2987 val |= 0x8; 2988 } 2989 if (modes & SHMEM_EEE_1G_ADV) { 2990 DP(NETIF_MSG_LINK, "Advertise 1GBase-T EEE\n"); 2991 val |= 0x4; 2992 } 2993 2994 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_EEE_ADV, val); 2995 2996 vars->eee_status &= ~SHMEM_EEE_ADV_STATUS_MASK; 2997 vars->eee_status |= (modes << SHMEM_EEE_ADV_STATUS_SHIFT); 2998 2999 return 0; 3000} 3001 3002static void bnx2x_update_mng_eee(struct link_params *params, u32 eee_status) 3003{ 3004 struct bnx2x *bp = params->bp; 3005 3006 if (bnx2x_eee_has_cap(params)) 3007 REG_WR(bp, params->shmem2_base + 3008 offsetof(struct shmem2_region, 3009 eee_status[params->port]), eee_status); 3010} 3011 3012static void bnx2x_eee_an_resolve(struct bnx2x_phy *phy, 3013 struct link_params *params, 3014 struct link_vars *vars) 3015{ 3016 struct bnx2x *bp = params->bp; 3017 u16 adv = 0, lp = 0; 3018 u32 lp_adv = 0; 3019 u8 neg = 0; 3020 3021 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_EEE_ADV, &adv); 3022 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_LP_EEE_ADV, &lp); 3023 3024 if (lp & 0x2) { 3025 lp_adv |= SHMEM_EEE_100M_ADV; 3026 if (adv & 0x2) { 3027 if (vars->line_speed == SPEED_100) 3028 neg = 1; 3029 DP(NETIF_MSG_LINK, "EEE negotiated - 100M\n"); 3030 } 3031 } 3032 if (lp & 0x14) { 3033 lp_adv |= SHMEM_EEE_1G_ADV; 3034 if (adv & 0x14) { 3035 if (vars->line_speed == SPEED_1000) 3036 neg = 1; 3037 DP(NETIF_MSG_LINK, "EEE negotiated - 1G\n"); 3038 } 3039 } 3040 if (lp & 0x68) { 3041 lp_adv |= SHMEM_EEE_10G_ADV; 3042 if (adv & 0x68) { 3043 if (vars->line_speed == SPEED_10000) 3044 neg = 1; 3045 DP(NETIF_MSG_LINK, "EEE negotiated - 10G\n"); 3046 } 3047 } 3048 3049 vars->eee_status &= ~SHMEM_EEE_LP_ADV_STATUS_MASK; 3050 vars->eee_status |= (lp_adv << SHMEM_EEE_LP_ADV_STATUS_SHIFT); 3051 3052 if (neg) { 3053 DP(NETIF_MSG_LINK, "EEE is active\n"); 3054 vars->eee_status |= SHMEM_EEE_ACTIVE_BIT; 3055 } 3056 3057} 3058 3059/******************************************************************/ 3060/* BSC access functions from E3 */ 3061/******************************************************************/ 3062static void bnx2x_bsc_module_sel(struct link_params *params) 3063{ 3064 int idx; 3065 u32 board_cfg, sfp_ctrl; 3066 u32 i2c_pins[I2C_SWITCH_WIDTH], i2c_val[I2C_SWITCH_WIDTH]; 3067 struct bnx2x *bp = params->bp; 3068 u8 port = params->port; 3069 /* Read I2C output PINs */ 3070 board_cfg = REG_RD(bp, params->shmem_base + 3071 offsetof(struct shmem_region, 3072 dev_info.shared_hw_config.board)); 3073 i2c_pins[I2C_BSC0] = board_cfg & SHARED_HW_CFG_E3_I2C_MUX0_MASK; 3074 i2c_pins[I2C_BSC1] = (board_cfg & SHARED_HW_CFG_E3_I2C_MUX1_MASK) >> 3075 SHARED_HW_CFG_E3_I2C_MUX1_SHIFT; 3076 3077 /* Read I2C output value */ 3078 sfp_ctrl = REG_RD(bp, params->shmem_base + 3079 offsetof(struct shmem_region, 3080 dev_info.port_hw_config[port].e3_cmn_pin_cfg)); 3081 i2c_val[I2C_BSC0] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX0_MASK) > 0; 3082 i2c_val[I2C_BSC1] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX1_MASK) > 0; 3083 DP(NETIF_MSG_LINK, "Setting BSC switch\n"); 3084 for (idx = 0; idx < I2C_SWITCH_WIDTH; idx++) 3085 bnx2x_set_cfg_pin(bp, i2c_pins[idx], i2c_val[idx]); 3086} 3087 3088static int bnx2x_bsc_read(struct link_params *params, 3089 struct bnx2x *bp, 3090 u8 sl_devid, 3091 u16 sl_addr, 3092 u8 lc_addr, 3093 u8 xfer_cnt, 3094 u32 *data_array) 3095{ 3096 u32 val, i; 3097 int rc = 0; 3098 3099 if (xfer_cnt > 16) { 3100 DP(NETIF_MSG_LINK, "invalid xfer_cnt %d. Max is 16 bytes\n", 3101 xfer_cnt); 3102 return -EINVAL; 3103 } 3104 bnx2x_bsc_module_sel(params); 3105 3106 xfer_cnt = 16 - lc_addr; 3107 3108 /* Enable the engine */ 3109 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND); 3110 val |= MCPR_IMC_COMMAND_ENABLE; 3111 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val); 3112 3113 /* Program slave device ID */ 3114 val = (sl_devid << 16) | sl_addr; 3115 REG_WR(bp, MCP_REG_MCPR_IMC_SLAVE_CONTROL, val); 3116 3117 /* Start xfer with 0 byte to update the address pointer ???*/ 3118 val = (MCPR_IMC_COMMAND_ENABLE) | 3119 (MCPR_IMC_COMMAND_WRITE_OP << 3120 MCPR_IMC_COMMAND_OPERATION_BITSHIFT) | 3121 (lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) | (0); 3122 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val); 3123 3124 /* Poll for completion */ 3125 i = 0; 3126 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND); 3127 while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) { 3128 udelay(10); 3129 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND); 3130 if (i++ > 1000) { 3131 DP(NETIF_MSG_LINK, "wr 0 byte timed out after %d try\n", 3132 i); 3133 rc = -EFAULT; 3134 break; 3135 } 3136 } 3137 if (rc == -EFAULT) 3138 return rc; 3139 3140 /* Start xfer with read op */ 3141 val = (MCPR_IMC_COMMAND_ENABLE) | 3142 (MCPR_IMC_COMMAND_READ_OP << 3143 MCPR_IMC_COMMAND_OPERATION_BITSHIFT) | 3144 (lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) | 3145 (xfer_cnt); 3146 REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val); 3147 3148 /* Poll for completion */ 3149 i = 0; 3150 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND); 3151 while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) { 3152 udelay(10); 3153 val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND); 3154 if (i++ > 1000) { 3155 DP(NETIF_MSG_LINK, "rd op timed out after %d try\n", i); 3156 rc = -EFAULT; 3157 break; 3158 } 3159 } 3160 if (rc == -EFAULT) 3161 return rc; 3162 3163 for (i = (lc_addr >> 2); i < 4; i++) { 3164 data_array[i] = REG_RD(bp, (MCP_REG_MCPR_IMC_DATAREG0 + i*4)); 3165#ifdef __BIG_ENDIAN 3166 data_array[i] = ((data_array[i] & 0x000000ff) << 24) | 3167 ((data_array[i] & 0x0000ff00) << 8) | 3168 ((data_array[i] & 0x00ff0000) >> 8) | 3169 ((data_array[i] & 0xff000000) >> 24); 3170#endif 3171 } 3172 return rc; 3173} 3174 3175static void bnx2x_cl45_read_or_write(struct bnx2x *bp, struct bnx2x_phy *phy, 3176 u8 devad, u16 reg, u16 or_val) 3177{ 3178 u16 val; 3179 bnx2x_cl45_read(bp, phy, devad, reg, &val); 3180 bnx2x_cl45_write(bp, phy, devad, reg, val | or_val); 3181} 3182 3183static void bnx2x_cl45_read_and_write(struct bnx2x *bp, 3184 struct bnx2x_phy *phy, 3185 u8 devad, u16 reg, u16 and_val) 3186{ 3187 u16 val; 3188 bnx2x_cl45_read(bp, phy, devad, reg, &val); 3189 bnx2x_cl45_write(bp, phy, devad, reg, val & and_val); 3190} 3191 3192int bnx2x_phy_read(struct link_params *params, u8 phy_addr, 3193 u8 devad, u16 reg, u16 *ret_val) 3194{ 3195 u8 phy_index; 3196 /* Probe for the phy according to the given phy_addr, and execute 3197 * the read request on it 3198 */ 3199 for (phy_index = 0; phy_index < params->num_phys; phy_index++) { 3200 if (params->phy[phy_index].addr == phy_addr) { 3201 return bnx2x_cl45_read(params->bp, 3202 ¶ms->phy[phy_index], devad, 3203 reg, ret_val); 3204 } 3205 } 3206 return -EINVAL; 3207} 3208 3209int bnx2x_phy_write(struct link_params *params, u8 phy_addr, 3210 u8 devad, u16 reg, u16 val) 3211{ 3212 u8 phy_index; 3213 /* Probe for the phy according to the given phy_addr, and execute 3214 * the write request on it 3215 */ 3216 for (phy_index = 0; phy_index < params->num_phys; phy_index++) { 3217 if (params->phy[phy_index].addr == phy_addr) { 3218 return bnx2x_cl45_write(params->bp, 3219 ¶ms->phy[phy_index], devad, 3220 reg, val); 3221 } 3222 } 3223 return -EINVAL; 3224} 3225static u8 bnx2x_get_warpcore_lane(struct bnx2x_phy *phy, 3226 struct link_params *params) 3227{ 3228 u8 lane = 0; 3229 struct bnx2x *bp = params->bp; 3230 u32 path_swap, path_swap_ovr; 3231 u8 path, port; 3232 3233 path = BP_PATH(bp); 3234 port = params->port; 3235 3236 if (bnx2x_is_4_port_mode(bp)) { 3237 u32 port_swap, port_swap_ovr; 3238 3239 /* Figure out path swap value */ 3240 path_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP_OVWR); 3241 if (path_swap_ovr & 0x1) 3242 path_swap = (path_swap_ovr & 0x2); 3243 else 3244 path_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP); 3245 3246 if (path_swap) 3247 path = path ^ 1; 3248 3249 /* Figure out port swap value */ 3250 port_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP_OVWR); 3251 if (port_swap_ovr & 0x1) 3252 port_swap = (port_swap_ovr & 0x2); 3253 else 3254 port_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP); 3255 3256 if (port_swap) 3257 port = port ^ 1; 3258 3259 lane = (port<<1) + path; 3260 } else { /* Two port mode - no port swap */ 3261 3262 /* Figure out path swap value */ 3263 path_swap_ovr = 3264 REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP_OVWR); 3265 if (path_swap_ovr & 0x1) { 3266 path_swap = (path_swap_ovr & 0x2); 3267 } else { 3268 path_swap = 3269 REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP); 3270 } 3271 if (path_swap) 3272 path = path ^ 1; 3273 3274 lane = path << 1 ; 3275 } 3276 return lane; 3277} 3278 3279static void bnx2x_set_aer_mmd(struct link_params *params, 3280 struct bnx2x_phy *phy) 3281{ 3282 u32 ser_lane; 3283 u16 offset, aer_val; 3284 struct bnx2x *bp = params->bp; 3285 ser_lane = ((params->lane_config & 3286 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> 3287 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); 3288 3289 offset = (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ? 3290 (phy->addr + ser_lane) : 0; 3291 3292 if (USES_WARPCORE(bp)) { 3293 aer_val = bnx2x_get_warpcore_lane(phy, params); 3294 /* In Dual-lane mode, two lanes are joined together, 3295 * so in order to configure them, the AER broadcast method is 3296 * used here. 3297 * 0x200 is the broadcast address for lanes 0,1 3298 * 0x201 is the broadcast address for lanes 2,3 3299 */ 3300 if (phy->flags & FLAGS_WC_DUAL_MODE) 3301 aer_val = (aer_val >> 1) | 0x200; 3302 } else if (CHIP_IS_E2(bp)) 3303 aer_val = 0x3800 + offset - 1; 3304 else 3305 aer_val = 0x3800 + offset; 3306 3307 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 3308 MDIO_AER_BLOCK_AER_REG, aer_val); 3309 3310} 3311 3312/******************************************************************/ 3313/* Internal phy section */ 3314/******************************************************************/ 3315 3316static void bnx2x_set_serdes_access(struct bnx2x *bp, u8 port) 3317{ 3318 u32 emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; 3319 3320 /* Set Clause 22 */ 3321 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 1); 3322 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000); 3323 udelay(500); 3324 REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f); 3325 udelay(500); 3326 /* Set Clause 45 */ 3327 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + port*0x10, 0); 3328} 3329 3330static void bnx2x_serdes_deassert(struct bnx2x *bp, u8 port) 3331{ 3332 u32 val; 3333 3334 DP(NETIF_MSG_LINK, "bnx2x_serdes_deassert\n"); 3335 3336 val = SERDES_RESET_BITS << (port*16); 3337 3338 /* Reset and unreset the SerDes/XGXS */ 3339 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val); 3340 udelay(500); 3341 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val); 3342 3343 bnx2x_set_serdes_access(bp, port); 3344 3345 REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + port*0x10, 3346 DEFAULT_PHY_DEV_ADDR); 3347} 3348 3349static void bnx2x_xgxs_specific_func(struct bnx2x_phy *phy, 3350 struct link_params *params, 3351 u32 action) 3352{ 3353 struct bnx2x *bp = params->bp; 3354 switch (action) { 3355 case PHY_INIT: 3356 /* Set correct devad */ 3357 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + params->port*0x18, 0); 3358 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + params->port*0x18, 3359 phy->def_md_devad); 3360 break; 3361 } 3362} 3363 3364static void bnx2x_xgxs_deassert(struct link_params *params) 3365{ 3366 struct bnx2x *bp = params->bp; 3367 u8 port; 3368 u32 val; 3369 DP(NETIF_MSG_LINK, "bnx2x_xgxs_deassert\n"); 3370 port = params->port; 3371 3372 val = XGXS_RESET_BITS << (port*16); 3373 3374 /* Reset and unreset the SerDes/XGXS */ 3375 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, val); 3376 udelay(500); 3377 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val); 3378 bnx2x_xgxs_specific_func(¶ms->phy[INT_PHY], params, 3379 PHY_INIT); 3380} 3381 3382static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy, 3383 struct link_params *params, u16 *ieee_fc) 3384{ 3385 struct bnx2x *bp = params->bp; 3386 *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; 3387 /* Resolve pause mode and advertisement Please refer to Table 3388 * 28B-3 of the 802.3ab-1999 spec 3389 */ 3390 3391 switch (phy->req_flow_ctrl) { 3392 case BNX2X_FLOW_CTRL_AUTO: 3393 switch (params->req_fc_auto_adv) { 3394 case BNX2X_FLOW_CTRL_BOTH: 3395 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; 3396 break; 3397 case BNX2X_FLOW_CTRL_RX: 3398 case BNX2X_FLOW_CTRL_TX: 3399 *ieee_fc |= 3400 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; 3401 break; 3402 default: 3403 break; 3404 } 3405 break; 3406 case BNX2X_FLOW_CTRL_TX: 3407 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; 3408 break; 3409 3410 case BNX2X_FLOW_CTRL_RX: 3411 case BNX2X_FLOW_CTRL_BOTH: 3412 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; 3413 break; 3414 3415 case BNX2X_FLOW_CTRL_NONE: 3416 default: 3417 *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; 3418 break; 3419 } 3420 DP(NETIF_MSG_LINK, "ieee_fc = 0x%x\n", *ieee_fc); 3421} 3422 3423static void set_phy_vars(struct link_params *params, 3424 struct link_vars *vars) 3425{ 3426 struct bnx2x *bp = params->bp; 3427 u8 actual_phy_idx, phy_index, link_cfg_idx; 3428 u8 phy_config_swapped = params->multi_phy_config & 3429 PORT_HW_CFG_PHY_SWAPPED_ENABLED; 3430 for (phy_index = INT_PHY; phy_index < params->num_phys; 3431 phy_index++) { 3432 link_cfg_idx = LINK_CONFIG_IDX(phy_index); 3433 actual_phy_idx = phy_index; 3434 if (phy_config_swapped) { 3435 if (phy_index == EXT_PHY1) 3436 actual_phy_idx = EXT_PHY2; 3437 else if (phy_index == EXT_PHY2) 3438 actual_phy_idx = EXT_PHY1; 3439 } 3440 params->phy[actual_phy_idx].req_flow_ctrl = 3441 params->req_flow_ctrl[link_cfg_idx]; 3442 3443 params->phy[actual_phy_idx].req_line_speed = 3444 params->req_line_speed[link_cfg_idx]; 3445 3446 params->phy[actual_phy_idx].speed_cap_mask = 3447 params->speed_cap_mask[link_cfg_idx]; 3448 3449 params->phy[actual_phy_idx].req_duplex = 3450 params->req_duplex[link_cfg_idx]; 3451 3452 if (params->req_line_speed[link_cfg_idx] == 3453 SPEED_AUTO_NEG) 3454 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED; 3455 3456 DP(NETIF_MSG_LINK, "req_flow_ctrl %x, req_line_speed %x," 3457 " speed_cap_mask %x\n", 3458 params->phy[actual_phy_idx].req_flow_ctrl, 3459 params->phy[actual_phy_idx].req_line_speed, 3460 params->phy[actual_phy_idx].speed_cap_mask); 3461 } 3462} 3463 3464static void bnx2x_ext_phy_set_pause(struct link_params *params, 3465 struct bnx2x_phy *phy, 3466 struct link_vars *vars) 3467{ 3468 u16 val; 3469 struct bnx2x *bp = params->bp; 3470 /* Read modify write pause advertizing */ 3471 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, &val); 3472 3473 val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH; 3474 3475 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ 3476 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc); 3477 if ((vars->ieee_fc & 3478 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == 3479 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { 3480 val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; 3481 } 3482 if ((vars->ieee_fc & 3483 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == 3484 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { 3485 val |= MDIO_AN_REG_ADV_PAUSE_PAUSE; 3486 } 3487 DP(NETIF_MSG_LINK, "Ext phy AN advertize 0x%x\n", val); 3488 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV_PAUSE, val); 3489} 3490 3491static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) 3492{ /* LD LP */ 3493 switch (pause_result) { /* ASYM P ASYM P */ 3494 case 0xb: /* 1 0 1 1 */ 3495 vars->flow_ctrl = BNX2X_FLOW_CTRL_TX; 3496 break; 3497 3498 case 0xe: /* 1 1 1 0 */ 3499 vars->flow_ctrl = BNX2X_FLOW_CTRL_RX; 3500 break; 3501 3502 case 0x5: /* 0 1 0 1 */ 3503 case 0x7: /* 0 1 1 1 */ 3504 case 0xd: /* 1 1 0 1 */ 3505 case 0xf: /* 1 1 1 1 */ 3506 vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH; 3507 break; 3508 3509 default: 3510 break; 3511 } 3512 if (pause_result & (1<<0)) 3513 vars->link_status |= LINK_STATUS_LINK_PARTNER_SYMMETRIC_PAUSE; 3514 if (pause_result & (1<<1)) 3515 vars->link_status |= LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE; 3516 3517} 3518 3519static void bnx2x_ext_phy_update_adv_fc(struct bnx2x_phy *phy, 3520 struct link_params *params, 3521 struct link_vars *vars) 3522{ 3523 u16 ld_pause; /* local */ 3524 u16 lp_pause; /* link partner */ 3525 u16 pause_result; 3526 struct bnx2x *bp = params->bp; 3527 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) { 3528 bnx2x_cl22_read(bp, phy, 0x4, &ld_pause); 3529 bnx2x_cl22_read(bp, phy, 0x5, &lp_pause); 3530 } else if (CHIP_IS_E3(bp) && 3531 SINGLE_MEDIA_DIRECT(params)) { 3532 u8 lane = bnx2x_get_warpcore_lane(phy, params); 3533 u16 gp_status, gp_mask; 3534 bnx2x_cl45_read(bp, phy, 3535 MDIO_AN_DEVAD, MDIO_WC_REG_GP2_STATUS_GP_2_4, 3536 &gp_status); 3537 gp_mask = (MDIO_WC_REG_GP2_STATUS_GP_2_4_CL73_AN_CMPL | 3538 MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_LP_AN_CAP) << 3539 lane; 3540 if ((gp_status & gp_mask) == gp_mask) { 3541 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 3542 MDIO_AN_REG_ADV_PAUSE, &ld_pause); 3543 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 3544 MDIO_AN_REG_LP_AUTO_NEG, &lp_pause); 3545 } else { 3546 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 3547 MDIO_AN_REG_CL37_FC_LD, &ld_pause); 3548 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 3549 MDIO_AN_REG_CL37_FC_LP, &lp_pause); 3550 ld_pause = ((ld_pause & 3551 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) 3552 << 3); 3553 lp_pause = ((lp_pause & 3554 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) 3555 << 3); 3556 } 3557 } else { 3558 bnx2x_cl45_read(bp, phy, 3559 MDIO_AN_DEVAD, 3560 MDIO_AN_REG_ADV_PAUSE, &ld_pause); 3561 bnx2x_cl45_read(bp, phy, 3562 MDIO_AN_DEVAD, 3563 MDIO_AN_REG_LP_AUTO_NEG, &lp_pause); 3564 } 3565 pause_result = (ld_pause & 3566 MDIO_AN_REG_ADV_PAUSE_MASK) >> 8; 3567 pause_result |= (lp_pause & 3568 MDIO_AN_REG_ADV_PAUSE_MASK) >> 10; 3569 DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x\n", pause_result); 3570 bnx2x_pause_resolve(vars, pause_result); 3571 3572} 3573 3574static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy, 3575 struct link_params *params, 3576 struct link_vars *vars) 3577{ 3578 u8 ret = 0; 3579 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 3580 if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO) { 3581 /* Update the advertised flow-controled of LD/LP in AN */ 3582 if (phy->req_line_speed == SPEED_AUTO_NEG) 3583 bnx2x_ext_phy_update_adv_fc(phy, params, vars); 3584 /* But set the flow-control result as the requested one */ 3585 vars->flow_ctrl = phy->req_flow_ctrl; 3586 } else if (phy->req_line_speed != SPEED_AUTO_NEG) 3587 vars->flow_ctrl = params->req_fc_auto_adv; 3588 else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) { 3589 ret = 1; 3590 bnx2x_ext_phy_update_adv_fc(phy, params, vars); 3591 } 3592 return ret; 3593} 3594/******************************************************************/ 3595/* Warpcore section */ 3596/******************************************************************/ 3597/* The init_internal_warpcore should mirror the xgxs, 3598 * i.e. reset the lane (if needed), set aer for the 3599 * init configuration, and set/clear SGMII flag. Internal 3600 * phy init is done purely in phy_init stage. 3601 */ 3602#define WC_TX_DRIVER(post2, idriver, ipre, ifir) \ 3603 ((post2 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) | \ 3604 (idriver << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) | \ 3605 (ipre << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET) | \ 3606 (ifir << MDIO_WC_REG_TX0_TX_DRIVER_IFIR_OFFSET)) 3607 3608#define WC_TX_FIR(post, main, pre) \ 3609 ((post << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) | \ 3610 (main << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) | \ 3611 (pre << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET)) 3612 3613static void bnx2x_warpcore_enable_AN_KR2(struct bnx2x_phy *phy, 3614 struct link_params *params, 3615 struct link_vars *vars) 3616{ 3617 struct bnx2x *bp = params->bp; 3618 u16 i; 3619 static struct bnx2x_reg_set reg_set[] = { 3620 /* Step 1 - Program the TX/RX alignment markers */ 3621 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL5, 0xa157}, 3622 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL7, 0xcbe2}, 3623 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL6, 0x7537}, 3624 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL9, 0xa157}, 3625 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL11, 0xcbe2}, 3626 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL10, 0x7537}, 3627 /* Step 2 - Configure the NP registers */ 3628 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_USERB0_CTRL, 0x000a}, 3629 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL1, 0x6400}, 3630 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL3, 0x0620}, 3631 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CODE_FIELD, 0x0157}, 3632 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI1, 0x6464}, 3633 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI2, 0x3150}, 3634 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI3, 0x3150}, 3635 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_BAM_CODE, 0x0157}, 3636 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_UD_CODE, 0x0620} 3637 }; 3638 DP(NETIF_MSG_LINK, "Enabling 20G-KR2\n"); 3639 3640 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3641 MDIO_WC_REG_CL49_USERB0_CTRL, (3<<6)); 3642 3643 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 3644 bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, 3645 reg_set[i].val); 3646 3647 /* Start KR2 work-around timer which handles BCM8073 link-parner */ 3648 params->link_attr_sync |= LINK_ATTR_SYNC_KR2_ENABLE; 3649 bnx2x_update_link_attr(params, params->link_attr_sync); 3650} 3651 3652static void bnx2x_disable_kr2(struct link_params *params, 3653 struct link_vars *vars, 3654 struct bnx2x_phy *phy) 3655{ 3656 struct bnx2x *bp = params->bp; 3657 int i; 3658 static struct bnx2x_reg_set reg_set[] = { 3659 /* Step 1 - Program the TX/RX alignment markers */ 3660 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL5, 0x7690}, 3661 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL7, 0xe647}, 3662 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL6, 0xc4f0}, 3663 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_TX_CTRL9, 0x7690}, 3664 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL11, 0xe647}, 3665 {MDIO_WC_DEVAD, MDIO_WC_REG_CL82_USERB1_RX_CTRL10, 0xc4f0}, 3666 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_USERB0_CTRL, 0x000c}, 3667 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL1, 0x6000}, 3668 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CTRL3, 0x0000}, 3669 {MDIO_WC_DEVAD, MDIO_WC_REG_CL73_BAM_CODE_FIELD, 0x0002}, 3670 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI1, 0x0000}, 3671 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI2, 0x0af7}, 3672 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_OUI3, 0x0af7}, 3673 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_BAM_CODE, 0x0002}, 3674 {MDIO_WC_DEVAD, MDIO_WC_REG_ETA_CL73_LD_UD_CODE, 0x0000} 3675 }; 3676 DP(NETIF_MSG_LINK, "Disabling 20G-KR2\n"); 3677 3678 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 3679 bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, 3680 reg_set[i].val); 3681 params->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE; 3682 bnx2x_update_link_attr(params, params->link_attr_sync); 3683 3684 vars->check_kr2_recovery_cnt = CHECK_KR2_RECOVERY_CNT; 3685} 3686 3687static void bnx2x_warpcore_set_lpi_passthrough(struct bnx2x_phy *phy, 3688 struct link_params *params) 3689{ 3690 struct bnx2x *bp = params->bp; 3691 3692 DP(NETIF_MSG_LINK, "Configure WC for LPI pass through\n"); 3693 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3694 MDIO_WC_REG_EEE_COMBO_CONTROL0, 0x7c); 3695 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3696 MDIO_WC_REG_DIGITAL4_MISC5, 0xc000); 3697} 3698 3699static void bnx2x_warpcore_restart_AN_KR(struct bnx2x_phy *phy, 3700 struct link_params *params) 3701{ 3702 /* Restart autoneg on the leading lane only */ 3703 struct bnx2x *bp = params->bp; 3704 u16 lane = bnx2x_get_warpcore_lane(phy, params); 3705 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 3706 MDIO_AER_BLOCK_AER_REG, lane); 3707 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 3708 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1200); 3709 3710 /* Restore AER */ 3711 bnx2x_set_aer_mmd(params, phy); 3712} 3713 3714static void bnx2x_warpcore_enable_AN_KR(struct bnx2x_phy *phy, 3715 struct link_params *params, 3716 struct link_vars *vars) { 3717 u16 lane, i, cl72_ctrl, an_adv = 0, val; 3718 u32 wc_lane_config; 3719 struct bnx2x *bp = params->bp; 3720 static struct bnx2x_reg_set reg_set[] = { 3721 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x7}, 3722 {MDIO_PMA_DEVAD, MDIO_WC_REG_IEEE0BLK_AUTONEGNP, 0x0}, 3723 {MDIO_WC_DEVAD, MDIO_WC_REG_RX66_CONTROL, 0x7415}, 3724 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_MISC2, 0x6190}, 3725 /* Disable Autoneg: re-enable it after adv is done. */ 3726 {MDIO_AN_DEVAD, MDIO_WC_REG_IEEE0BLK_MIICNTL, 0}, 3727 {MDIO_PMA_DEVAD, MDIO_WC_REG_PMD_KR_CONTROL, 0x2}, 3728 {MDIO_WC_DEVAD, MDIO_WC_REG_CL72_USERB0_CL72_TX_FIR_TAP, 0}, 3729 }; 3730 DP(NETIF_MSG_LINK, "Enable Auto Negotiation for KR\n"); 3731 /* Set to default registers that may be overriden by 10G force */ 3732 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 3733 bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, 3734 reg_set[i].val); 3735 3736 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3737 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, &cl72_ctrl); 3738 cl72_ctrl &= 0x08ff; 3739 cl72_ctrl |= 0x3800; 3740 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3741 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, cl72_ctrl); 3742 3743 /* Check adding advertisement for 1G KX */ 3744 if (((vars->line_speed == SPEED_AUTO_NEG) && 3745 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || 3746 (vars->line_speed == SPEED_1000)) { 3747 u16 addr = MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2; 3748 an_adv |= (1<<5); 3749 3750 /* Enable CL37 1G Parallel Detect */ 3751 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, addr, 0x1); 3752 DP(NETIF_MSG_LINK, "Advertize 1G\n"); 3753 } 3754 if (((vars->line_speed == SPEED_AUTO_NEG) && 3755 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) || 3756 (vars->line_speed == SPEED_10000)) { 3757 /* Check adding advertisement for 10G KR */ 3758 an_adv |= (1<<7); 3759 /* Enable 10G Parallel Detect */ 3760 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 3761 MDIO_AER_BLOCK_AER_REG, 0); 3762 3763 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 3764 MDIO_WC_REG_PAR_DET_10G_CTRL, 1); 3765 bnx2x_set_aer_mmd(params, phy); 3766 DP(NETIF_MSG_LINK, "Advertize 10G\n"); 3767 } 3768 3769 /* Set Transmit PMD settings */ 3770 lane = bnx2x_get_warpcore_lane(phy, params); 3771 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3772 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 3773 WC_TX_DRIVER(0x02, 0x06, 0x09, 0)); 3774 /* Configure the next lane if dual mode */ 3775 if (phy->flags & FLAGS_WC_DUAL_MODE) 3776 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3777 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*(lane+1), 3778 WC_TX_DRIVER(0x02, 0x06, 0x09, 0)); 3779 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3780 MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL, 3781 0x03f0); 3782 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3783 MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL, 3784 0x03f0); 3785 3786 /* Advertised speeds */ 3787 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 3788 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, an_adv); 3789 3790 /* Advertised and set FEC (Forward Error Correction) */ 3791 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 3792 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT2, 3793 (MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_ABILITY | 3794 MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_REQ)); 3795 3796 /* Enable CL37 BAM */ 3797 if (REG_RD(bp, params->shmem_base + 3798 offsetof(struct shmem_region, dev_info. 3799 port_hw_config[params->port].default_cfg)) & 3800 PORT_HW_CFG_ENABLE_BAM_ON_KR_ENABLED) { 3801 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3802 MDIO_WC_REG_DIGITAL6_MP5_NEXTPAGECTRL, 3803 1); 3804 DP(NETIF_MSG_LINK, "Enable CL37 BAM on KR\n"); 3805 } 3806 3807 /* Advertise pause */ 3808 bnx2x_ext_phy_set_pause(params, phy, vars); 3809 vars->rx_tx_asic_rst = MAX_KR_LINK_RETRY; 3810 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3811 MDIO_WC_REG_DIGITAL5_MISC7, 0x100); 3812 3813 /* Over 1G - AN local device user page 1 */ 3814 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3815 MDIO_WC_REG_DIGITAL3_UP1, 0x1f); 3816 3817 if (((phy->req_line_speed == SPEED_AUTO_NEG) && 3818 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_20G)) || 3819 (phy->req_line_speed == SPEED_20000)) { 3820 3821 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 3822 MDIO_AER_BLOCK_AER_REG, lane); 3823 3824 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3825 MDIO_WC_REG_RX1_PCI_CTRL + (0x10*lane), 3826 (1<<11)); 3827 3828 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3829 MDIO_WC_REG_XGXS_X2_CONTROL3, 0x7); 3830 bnx2x_set_aer_mmd(params, phy); 3831 3832 bnx2x_warpcore_enable_AN_KR2(phy, params, vars); 3833 } else { 3834 /* Enable Auto-Detect to support 1G over CL37 as well */ 3835 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3836 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 0x10); 3837 wc_lane_config = REG_RD(bp, params->shmem_base + 3838 offsetof(struct shmem_region, dev_info. 3839 shared_hw_config.wc_lane_config)); 3840 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3841 MDIO_WC_REG_RX0_PCI_CTRL + (lane << 4), &val); 3842 /* Force cl48 sync_status LOW to avoid getting stuck in CL73 3843 * parallel-detect loop when CL73 and CL37 are enabled. 3844 */ 3845 val |= 1 << 11; 3846 3847 /* Restore Polarity settings in case it was run over by 3848 * previous link owner 3849 */ 3850 if (wc_lane_config & 3851 (SHARED_HW_CFG_RX_LANE0_POL_FLIP_ENABLED << lane)) 3852 val |= 3 << 2; 3853 else 3854 val &= ~(3 << 2); 3855 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3856 MDIO_WC_REG_RX0_PCI_CTRL + (lane << 4), 3857 val); 3858 3859 bnx2x_disable_kr2(params, vars, phy); 3860 } 3861 3862 /* Enable Autoneg: only on the main lane */ 3863 bnx2x_warpcore_restart_AN_KR(phy, params); 3864} 3865 3866static void bnx2x_warpcore_set_10G_KR(struct bnx2x_phy *phy, 3867 struct link_params *params, 3868 struct link_vars *vars) 3869{ 3870 struct bnx2x *bp = params->bp; 3871 u16 val16, i, lane; 3872 static struct bnx2x_reg_set reg_set[] = { 3873 /* Disable Autoneg */ 3874 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x7}, 3875 {MDIO_WC_DEVAD, MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, 3876 0x3f00}, 3877 {MDIO_AN_DEVAD, MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, 0}, 3878 {MDIO_AN_DEVAD, MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0}, 3879 {MDIO_WC_DEVAD, MDIO_WC_REG_DIGITAL3_UP1, 0x1}, 3880 {MDIO_WC_DEVAD, MDIO_WC_REG_DIGITAL5_MISC7, 0xa}, 3881 /* Leave cl72 training enable, needed for KR */ 3882 {MDIO_PMA_DEVAD, MDIO_WC_REG_PMD_KR_CONTROL, 0x2} 3883 }; 3884 3885 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 3886 bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, 3887 reg_set[i].val); 3888 3889 lane = bnx2x_get_warpcore_lane(phy, params); 3890 /* Global registers */ 3891 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 3892 MDIO_AER_BLOCK_AER_REG, 0); 3893 /* Disable CL36 PCS Tx */ 3894 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3895 MDIO_WC_REG_XGXSBLK1_LANECTRL0, &val16); 3896 val16 &= ~(0x0011 << lane); 3897 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3898 MDIO_WC_REG_XGXSBLK1_LANECTRL0, val16); 3899 3900 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3901 MDIO_WC_REG_XGXSBLK1_LANECTRL1, &val16); 3902 val16 |= (0x0303 << (lane << 1)); 3903 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3904 MDIO_WC_REG_XGXSBLK1_LANECTRL1, val16); 3905 /* Restore AER */ 3906 bnx2x_set_aer_mmd(params, phy); 3907 /* Set speed via PMA/PMD register */ 3908 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 3909 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040); 3910 3911 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 3912 MDIO_WC_REG_IEEE0BLK_AUTONEGNP, 0xB); 3913 3914 /* Enable encoded forced speed */ 3915 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3916 MDIO_WC_REG_SERDESDIGITAL_MISC2, 0x30); 3917 3918 /* Turn TX scramble payload only the 64/66 scrambler */ 3919 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3920 MDIO_WC_REG_TX66_CONTROL, 0x9); 3921 3922 /* Turn RX scramble payload only the 64/66 scrambler */ 3923 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3924 MDIO_WC_REG_RX66_CONTROL, 0xF9); 3925 3926 /* Set and clear loopback to cause a reset to 64/66 decoder */ 3927 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3928 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x4000); 3929 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3930 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0); 3931 3932} 3933 3934static void bnx2x_warpcore_set_10G_XFI(struct bnx2x_phy *phy, 3935 struct link_params *params, 3936 u8 is_xfi) 3937{ 3938 struct bnx2x *bp = params->bp; 3939 u16 misc1_val, tap_val, tx_driver_val, lane, val; 3940 u32 cfg_tap_val, tx_drv_brdct, tx_equal; 3941 u32 ifir_val, ipost2_val, ipre_driver_val; 3942 3943 /* Hold rxSeqStart */ 3944 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3945 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, 0x8000); 3946 3947 /* Hold tx_fifo_reset */ 3948 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3949 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, 0x1); 3950 3951 /* Disable CL73 AN */ 3952 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0); 3953 3954 /* Disable 100FX Enable and Auto-Detect */ 3955 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 3956 MDIO_WC_REG_FX100_CTRL1, 0xFFFA); 3957 3958 /* Disable 100FX Idle detect */ 3959 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 3960 MDIO_WC_REG_FX100_CTRL3, 0x0080); 3961 3962 /* Set Block address to Remote PHY & Clear forced_speed[5] */ 3963 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 3964 MDIO_WC_REG_DIGITAL4_MISC3, 0xFF7F); 3965 3966 /* Turn off auto-detect & fiber mode */ 3967 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 3968 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 3969 0xFFEE); 3970 3971 /* Set filter_force_link, disable_false_link and parallel_detect */ 3972 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3973 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &val); 3974 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 3975 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 3976 ((val | 0x0006) & 0xFFFE)); 3977 3978 /* Set XFI / SFI */ 3979 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 3980 MDIO_WC_REG_SERDESDIGITAL_MISC1, &misc1_val); 3981 3982 misc1_val &= ~(0x1f); 3983 3984 if (is_xfi) { 3985 misc1_val |= 0x5; 3986 tap_val = WC_TX_FIR(0x08, 0x37, 0x00); 3987 tx_driver_val = WC_TX_DRIVER(0x00, 0x02, 0x03, 0); 3988 } else { 3989 cfg_tap_val = REG_RD(bp, params->shmem_base + 3990 offsetof(struct shmem_region, dev_info. 3991 port_hw_config[params->port]. 3992 sfi_tap_values)); 3993 3994 tx_equal = cfg_tap_val & PORT_HW_CFG_TX_EQUALIZATION_MASK; 3995 3996 misc1_val |= 0x9; 3997 3998 /* TAP values are controlled by nvram, if value there isn't 0 */ 3999 if (tx_equal) 4000 tap_val = (u16)tx_equal; 4001 else 4002 tap_val = WC_TX_FIR(0x0f, 0x2b, 0x02); 4003 4004 ifir_val = DEFAULT_TX_DRV_IFIR; 4005 ipost2_val = DEFAULT_TX_DRV_POST2; 4006 ipre_driver_val = DEFAULT_TX_DRV_IPRE_DRIVER; 4007 tx_drv_brdct = DEFAULT_TX_DRV_BRDCT; 4008 4009 /* If any of the IFIR/IPRE_DRIVER/POST@ is set, apply all 4010 * configuration. 4011 */ 4012 if (cfg_tap_val & (PORT_HW_CFG_TX_DRV_IFIR_MASK | 4013 PORT_HW_CFG_TX_DRV_IPREDRIVER_MASK | 4014 PORT_HW_CFG_TX_DRV_POST2_MASK)) { 4015 ifir_val = (cfg_tap_val & 4016 PORT_HW_CFG_TX_DRV_IFIR_MASK) >> 4017 PORT_HW_CFG_TX_DRV_IFIR_SHIFT; 4018 ipre_driver_val = (cfg_tap_val & 4019 PORT_HW_CFG_TX_DRV_IPREDRIVER_MASK) 4020 >> PORT_HW_CFG_TX_DRV_IPREDRIVER_SHIFT; 4021 ipost2_val = (cfg_tap_val & 4022 PORT_HW_CFG_TX_DRV_POST2_MASK) >> 4023 PORT_HW_CFG_TX_DRV_POST2_SHIFT; 4024 } 4025 4026 if (cfg_tap_val & PORT_HW_CFG_TX_DRV_BROADCAST_MASK) { 4027 tx_drv_brdct = (cfg_tap_val & 4028 PORT_HW_CFG_TX_DRV_BROADCAST_MASK) >> 4029 PORT_HW_CFG_TX_DRV_BROADCAST_SHIFT; 4030 } 4031 4032 tx_driver_val = WC_TX_DRIVER(ipost2_val, tx_drv_brdct, 4033 ipre_driver_val, ifir_val); 4034 } 4035 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4036 MDIO_WC_REG_SERDESDIGITAL_MISC1, misc1_val); 4037 4038 /* Set Transmit PMD settings */ 4039 lane = bnx2x_get_warpcore_lane(phy, params); 4040 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4041 MDIO_WC_REG_TX_FIR_TAP, 4042 tap_val | MDIO_WC_REG_TX_FIR_TAP_ENABLE); 4043 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4044 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 4045 tx_driver_val); 4046 4047 /* Enable fiber mode, enable and invert sig_det */ 4048 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4049 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 0xd); 4050 4051 /* Set Block address to Remote PHY & Set forced_speed[5], 40bit mode */ 4052 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4053 MDIO_WC_REG_DIGITAL4_MISC3, 0x8080); 4054 4055 bnx2x_warpcore_set_lpi_passthrough(phy, params); 4056 4057 /* 10G XFI Full Duplex */ 4058 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4059 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x100); 4060 4061 /* Release tx_fifo_reset */ 4062 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4063 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, 4064 0xFFFE); 4065 /* Release rxSeqStart */ 4066 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4067 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, 0x7FFF); 4068} 4069 4070static void bnx2x_warpcore_set_20G_force_KR2(struct bnx2x_phy *phy, 4071 struct link_params *params) 4072{ 4073 u16 val; 4074 struct bnx2x *bp = params->bp; 4075 /* Set global registers, so set AER lane to 0 */ 4076 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 4077 MDIO_AER_BLOCK_AER_REG, 0); 4078 4079 /* Disable sequencer */ 4080 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4081 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL, ~(1<<13)); 4082 4083 bnx2x_set_aer_mmd(params, phy); 4084 4085 bnx2x_cl45_read_and_write(bp, phy, MDIO_PMA_DEVAD, 4086 MDIO_WC_REG_PMD_KR_CONTROL, ~(1<<1)); 4087 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 4088 MDIO_AN_REG_CTRL, 0); 4089 /* Turn off CL73 */ 4090 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4091 MDIO_WC_REG_CL73_USERB0_CTRL, &val); 4092 val &= ~(1<<5); 4093 val |= (1<<6); 4094 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4095 MDIO_WC_REG_CL73_USERB0_CTRL, val); 4096 4097 /* Set 20G KR2 force speed */ 4098 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4099 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x1f); 4100 4101 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4102 MDIO_WC_REG_DIGITAL4_MISC3, (1<<7)); 4103 4104 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4105 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, &val); 4106 val &= ~(3<<14); 4107 val |= (1<<15); 4108 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4109 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, val); 4110 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4111 MDIO_WC_REG_CL72_USERB0_CL72_TX_FIR_TAP, 0x835A); 4112 4113 /* Enable sequencer (over lane 0) */ 4114 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 4115 MDIO_AER_BLOCK_AER_REG, 0); 4116 4117 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4118 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL, (1<<13)); 4119 4120 bnx2x_set_aer_mmd(params, phy); 4121} 4122 4123static void bnx2x_warpcore_set_20G_DXGXS(struct bnx2x *bp, 4124 struct bnx2x_phy *phy, 4125 u16 lane) 4126{ 4127 /* Rx0 anaRxControl1G */ 4128 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4129 MDIO_WC_REG_RX0_ANARXCONTROL1G, 0x90); 4130 4131 /* Rx2 anaRxControl1G */ 4132 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4133 MDIO_WC_REG_RX2_ANARXCONTROL1G, 0x90); 4134 4135 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4136 MDIO_WC_REG_RX66_SCW0, 0xE070); 4137 4138 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4139 MDIO_WC_REG_RX66_SCW1, 0xC0D0); 4140 4141 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4142 MDIO_WC_REG_RX66_SCW2, 0xA0B0); 4143 4144 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4145 MDIO_WC_REG_RX66_SCW3, 0x8090); 4146 4147 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4148 MDIO_WC_REG_RX66_SCW0_MASK, 0xF0F0); 4149 4150 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4151 MDIO_WC_REG_RX66_SCW1_MASK, 0xF0F0); 4152 4153 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4154 MDIO_WC_REG_RX66_SCW2_MASK, 0xF0F0); 4155 4156 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4157 MDIO_WC_REG_RX66_SCW3_MASK, 0xF0F0); 4158 4159 /* Serdes Digital Misc1 */ 4160 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4161 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6008); 4162 4163 /* Serdes Digital4 Misc3 */ 4164 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4165 MDIO_WC_REG_DIGITAL4_MISC3, 0x8088); 4166 4167 /* Set Transmit PMD settings */ 4168 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4169 MDIO_WC_REG_TX_FIR_TAP, 4170 (WC_TX_FIR(0x12, 0x2d, 0x00) | 4171 MDIO_WC_REG_TX_FIR_TAP_ENABLE)); 4172 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4173 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 4174 WC_TX_DRIVER(0x02, 0x02, 0x02, 0)); 4175} 4176 4177static void bnx2x_warpcore_set_sgmii_speed(struct bnx2x_phy *phy, 4178 struct link_params *params, 4179 u8 fiber_mode, 4180 u8 always_autoneg) 4181{ 4182 struct bnx2x *bp = params->bp; 4183 u16 val16, digctrl_kx1, digctrl_kx2; 4184 4185 /* Clear XFI clock comp in non-10G single lane mode. */ 4186 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4187 MDIO_WC_REG_RX66_CONTROL, ~(3<<13)); 4188 4189 bnx2x_warpcore_set_lpi_passthrough(phy, params); 4190 4191 if (always_autoneg || phy->req_line_speed == SPEED_AUTO_NEG) { 4192 /* SGMII Autoneg */ 4193 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4194 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 4195 0x1000); 4196 DP(NETIF_MSG_LINK, "set SGMII AUTONEG\n"); 4197 } else { 4198 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4199 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16); 4200 val16 &= 0xcebf; 4201 switch (phy->req_line_speed) { 4202 case SPEED_10: 4203 break; 4204 case SPEED_100: 4205 val16 |= 0x2000; 4206 break; 4207 case SPEED_1000: 4208 val16 |= 0x0040; 4209 break; 4210 default: 4211 DP(NETIF_MSG_LINK, 4212 "Speed not supported: 0x%x\n", phy->req_line_speed); 4213 return; 4214 } 4215 4216 if (phy->req_duplex == DUPLEX_FULL) 4217 val16 |= 0x0100; 4218 4219 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4220 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16); 4221 4222 DP(NETIF_MSG_LINK, "set SGMII force speed %d\n", 4223 phy->req_line_speed); 4224 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4225 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16); 4226 DP(NETIF_MSG_LINK, " (readback) %x\n", val16); 4227 } 4228 4229 /* SGMII Slave mode and disable signal detect */ 4230 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4231 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &digctrl_kx1); 4232 if (fiber_mode) 4233 digctrl_kx1 = 1; 4234 else 4235 digctrl_kx1 &= 0xff4a; 4236 4237 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4238 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 4239 digctrl_kx1); 4240 4241 /* Turn off parallel detect */ 4242 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4243 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &digctrl_kx2); 4244 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4245 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 4246 (digctrl_kx2 & ~(1<<2))); 4247 4248 /* Re-enable parallel detect */ 4249 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4250 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 4251 (digctrl_kx2 | (1<<2))); 4252 4253 /* Enable autodet */ 4254 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4255 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 4256 (digctrl_kx1 | 0x10)); 4257} 4258 4259static void bnx2x_warpcore_reset_lane(struct bnx2x *bp, 4260 struct bnx2x_phy *phy, 4261 u8 reset) 4262{ 4263 u16 val; 4264 /* Take lane out of reset after configuration is finished */ 4265 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4266 MDIO_WC_REG_DIGITAL5_MISC6, &val); 4267 if (reset) 4268 val |= 0xC000; 4269 else 4270 val &= 0x3FFF; 4271 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4272 MDIO_WC_REG_DIGITAL5_MISC6, val); 4273 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4274 MDIO_WC_REG_DIGITAL5_MISC6, &val); 4275} 4276/* Clear SFI/XFI link settings registers */ 4277static void bnx2x_warpcore_clear_regs(struct bnx2x_phy *phy, 4278 struct link_params *params, 4279 u16 lane) 4280{ 4281 struct bnx2x *bp = params->bp; 4282 u16 i; 4283 static struct bnx2x_reg_set wc_regs[] = { 4284 {MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0}, 4285 {MDIO_WC_DEVAD, MDIO_WC_REG_FX100_CTRL1, 0x014a}, 4286 {MDIO_WC_DEVAD, MDIO_WC_REG_FX100_CTRL3, 0x0800}, 4287 {MDIO_WC_DEVAD, MDIO_WC_REG_DIGITAL4_MISC3, 0x8008}, 4288 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 4289 0x0195}, 4290 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 4291 0x0007}, 4292 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, 4293 0x0002}, 4294 {MDIO_WC_DEVAD, MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6000}, 4295 {MDIO_WC_DEVAD, MDIO_WC_REG_TX_FIR_TAP, 0x0000}, 4296 {MDIO_WC_DEVAD, MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040}, 4297 {MDIO_WC_DEVAD, MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 0x0140} 4298 }; 4299 /* Set XFI clock comp as default. */ 4300 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4301 MDIO_WC_REG_RX66_CONTROL, (3<<13)); 4302 4303 for (i = 0; i < ARRAY_SIZE(wc_regs); i++) 4304 bnx2x_cl45_write(bp, phy, wc_regs[i].devad, wc_regs[i].reg, 4305 wc_regs[i].val); 4306 4307 lane = bnx2x_get_warpcore_lane(phy, params); 4308 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4309 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 0x0990); 4310 4311} 4312 4313static int bnx2x_get_mod_abs_int_cfg(struct bnx2x *bp, 4314 u32 chip_id, 4315 u32 shmem_base, u8 port, 4316 u8 *gpio_num, u8 *gpio_port) 4317{ 4318 u32 cfg_pin; 4319 *gpio_num = 0; 4320 *gpio_port = 0; 4321 if (CHIP_IS_E3(bp)) { 4322 cfg_pin = (REG_RD(bp, shmem_base + 4323 offsetof(struct shmem_region, 4324 dev_info.port_hw_config[port].e3_sfp_ctrl)) & 4325 PORT_HW_CFG_E3_MOD_ABS_MASK) >> 4326 PORT_HW_CFG_E3_MOD_ABS_SHIFT; 4327 4328 /* Should not happen. This function called upon interrupt 4329 * triggered by GPIO ( since EPIO can only generate interrupts 4330 * to MCP). 4331 * So if this function was called and none of the GPIOs was set, 4332 * it means the shit hit the fan. 4333 */ 4334 if ((cfg_pin < PIN_CFG_GPIO0_P0) || 4335 (cfg_pin > PIN_CFG_GPIO3_P1)) { 4336 DP(NETIF_MSG_LINK, 4337 "No cfg pin %x for module detect indication\n", 4338 cfg_pin); 4339 return -EINVAL; 4340 } 4341 4342 *gpio_num = (cfg_pin - PIN_CFG_GPIO0_P0) & 0x3; 4343 *gpio_port = (cfg_pin - PIN_CFG_GPIO0_P0) >> 2; 4344 } else { 4345 *gpio_num = MISC_REGISTERS_GPIO_3; 4346 *gpio_port = port; 4347 } 4348 4349 return 0; 4350} 4351 4352static int bnx2x_is_sfp_module_plugged(struct bnx2x_phy *phy, 4353 struct link_params *params) 4354{ 4355 struct bnx2x *bp = params->bp; 4356 u8 gpio_num, gpio_port; 4357 u32 gpio_val; 4358 if (bnx2x_get_mod_abs_int_cfg(bp, params->chip_id, 4359 params->shmem_base, params->port, 4360 &gpio_num, &gpio_port) != 0) 4361 return 0; 4362 gpio_val = bnx2x_get_gpio(bp, gpio_num, gpio_port); 4363 4364 /* Call the handling function in case module is detected */ 4365 if (gpio_val == 0) 4366 return 1; 4367 else 4368 return 0; 4369} 4370static int bnx2x_warpcore_get_sigdet(struct bnx2x_phy *phy, 4371 struct link_params *params) 4372{ 4373 u16 gp2_status_reg0, lane; 4374 struct bnx2x *bp = params->bp; 4375 4376 lane = bnx2x_get_warpcore_lane(phy, params); 4377 4378 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, MDIO_WC_REG_GP2_STATUS_GP_2_0, 4379 &gp2_status_reg0); 4380 4381 return (gp2_status_reg0 >> (8+lane)) & 0x1; 4382} 4383 4384static void bnx2x_warpcore_config_runtime(struct bnx2x_phy *phy, 4385 struct link_params *params, 4386 struct link_vars *vars) 4387{ 4388 struct bnx2x *bp = params->bp; 4389 u32 serdes_net_if; 4390 u16 gp_status1 = 0, lnkup = 0, lnkup_kr = 0; 4391 4392 vars->turn_to_run_wc_rt = vars->turn_to_run_wc_rt ? 0 : 1; 4393 4394 if (!vars->turn_to_run_wc_rt) 4395 return; 4396 4397 if (vars->rx_tx_asic_rst) { 4398 u16 lane = bnx2x_get_warpcore_lane(phy, params); 4399 serdes_net_if = (REG_RD(bp, params->shmem_base + 4400 offsetof(struct shmem_region, dev_info. 4401 port_hw_config[params->port].default_cfg)) & 4402 PORT_HW_CFG_NET_SERDES_IF_MASK); 4403 4404 switch (serdes_net_if) { 4405 case PORT_HW_CFG_NET_SERDES_IF_KR: 4406 /* Do we get link yet? */ 4407 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 0x81d1, 4408 &gp_status1); 4409 lnkup = (gp_status1 >> (8+lane)) & 0x1;/* 1G */ 4410 /*10G KR*/ 4411 lnkup_kr = (gp_status1 >> (12+lane)) & 0x1; 4412 4413 if (lnkup_kr || lnkup) { 4414 vars->rx_tx_asic_rst = 0; 4415 } else { 4416 /* Reset the lane to see if link comes up.*/ 4417 bnx2x_warpcore_reset_lane(bp, phy, 1); 4418 bnx2x_warpcore_reset_lane(bp, phy, 0); 4419 4420 /* Restart Autoneg */ 4421 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 4422 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1200); 4423 4424 vars->rx_tx_asic_rst--; 4425 DP(NETIF_MSG_LINK, "0x%x retry left\n", 4426 vars->rx_tx_asic_rst); 4427 } 4428 break; 4429 4430 default: 4431 break; 4432 } 4433 4434 } /*params->rx_tx_asic_rst*/ 4435 4436} 4437static void bnx2x_warpcore_config_sfi(struct bnx2x_phy *phy, 4438 struct link_params *params) 4439{ 4440 u16 lane = bnx2x_get_warpcore_lane(phy, params); 4441 struct bnx2x *bp = params->bp; 4442 bnx2x_warpcore_clear_regs(phy, params, lane); 4443 if ((params->req_line_speed[LINK_CONFIG_IDX(INT_PHY)] == 4444 SPEED_10000) && 4445 (phy->media_type != ETH_PHY_SFP_1G_FIBER)) { 4446 DP(NETIF_MSG_LINK, "Setting 10G SFI\n"); 4447 bnx2x_warpcore_set_10G_XFI(phy, params, 0); 4448 } else { 4449 DP(NETIF_MSG_LINK, "Setting 1G Fiber\n"); 4450 bnx2x_warpcore_set_sgmii_speed(phy, params, 1, 0); 4451 } 4452} 4453 4454static void bnx2x_sfp_e3_set_transmitter(struct link_params *params, 4455 struct bnx2x_phy *phy, 4456 u8 tx_en) 4457{ 4458 struct bnx2x *bp = params->bp; 4459 u32 cfg_pin; 4460 u8 port = params->port; 4461 4462 cfg_pin = REG_RD(bp, params->shmem_base + 4463 offsetof(struct shmem_region, 4464 dev_info.port_hw_config[port].e3_sfp_ctrl)) & 4465 PORT_HW_CFG_E3_TX_LASER_MASK; 4466 /* Set the !tx_en since this pin is DISABLE_TX_LASER */ 4467 DP(NETIF_MSG_LINK, "Setting WC TX to %d\n", tx_en); 4468 4469 /* For 20G, the expected pin to be used is 3 pins after the current */ 4470 bnx2x_set_cfg_pin(bp, cfg_pin, tx_en ^ 1); 4471 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_20G) 4472 bnx2x_set_cfg_pin(bp, cfg_pin + 3, tx_en ^ 1); 4473} 4474 4475static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy, 4476 struct link_params *params, 4477 struct link_vars *vars) 4478{ 4479 struct bnx2x *bp = params->bp; 4480 u32 serdes_net_if; 4481 u8 fiber_mode; 4482 u16 lane = bnx2x_get_warpcore_lane(phy, params); 4483 serdes_net_if = (REG_RD(bp, params->shmem_base + 4484 offsetof(struct shmem_region, dev_info. 4485 port_hw_config[params->port].default_cfg)) & 4486 PORT_HW_CFG_NET_SERDES_IF_MASK); 4487 DP(NETIF_MSG_LINK, "Begin Warpcore init, link_speed %d, " 4488 "serdes_net_if = 0x%x\n", 4489 vars->line_speed, serdes_net_if); 4490 bnx2x_set_aer_mmd(params, phy); 4491 bnx2x_warpcore_reset_lane(bp, phy, 1); 4492 vars->phy_flags |= PHY_XGXS_FLAG; 4493 if ((serdes_net_if == PORT_HW_CFG_NET_SERDES_IF_SGMII) || 4494 (phy->req_line_speed && 4495 ((phy->req_line_speed == SPEED_100) || 4496 (phy->req_line_speed == SPEED_10)))) { 4497 vars->phy_flags |= PHY_SGMII_FLAG; 4498 DP(NETIF_MSG_LINK, "Setting SGMII mode\n"); 4499 bnx2x_warpcore_clear_regs(phy, params, lane); 4500 bnx2x_warpcore_set_sgmii_speed(phy, params, 0, 1); 4501 } else { 4502 switch (serdes_net_if) { 4503 case PORT_HW_CFG_NET_SERDES_IF_KR: 4504 /* Enable KR Auto Neg */ 4505 if (params->loopback_mode != LOOPBACK_EXT) 4506 bnx2x_warpcore_enable_AN_KR(phy, params, vars); 4507 else { 4508 DP(NETIF_MSG_LINK, "Setting KR 10G-Force\n"); 4509 bnx2x_warpcore_set_10G_KR(phy, params, vars); 4510 } 4511 break; 4512 4513 case PORT_HW_CFG_NET_SERDES_IF_XFI: 4514 bnx2x_warpcore_clear_regs(phy, params, lane); 4515 if (vars->line_speed == SPEED_10000) { 4516 DP(NETIF_MSG_LINK, "Setting 10G XFI\n"); 4517 bnx2x_warpcore_set_10G_XFI(phy, params, 1); 4518 } else { 4519 if (SINGLE_MEDIA_DIRECT(params)) { 4520 DP(NETIF_MSG_LINK, "1G Fiber\n"); 4521 fiber_mode = 1; 4522 } else { 4523 DP(NETIF_MSG_LINK, "10/100/1G SGMII\n"); 4524 fiber_mode = 0; 4525 } 4526 bnx2x_warpcore_set_sgmii_speed(phy, 4527 params, 4528 fiber_mode, 4529 0); 4530 } 4531 4532 break; 4533 4534 case PORT_HW_CFG_NET_SERDES_IF_SFI: 4535 /* Issue Module detection if module is plugged, or 4536 * enabled transmitter to avoid current leakage in case 4537 * no module is connected 4538 */ 4539 if ((params->loopback_mode == LOOPBACK_NONE) || 4540 (params->loopback_mode == LOOPBACK_EXT)) { 4541 if (bnx2x_is_sfp_module_plugged(phy, params)) 4542 bnx2x_sfp_module_detection(phy, params); 4543 else 4544 bnx2x_sfp_e3_set_transmitter(params, 4545 phy, 1); 4546 } 4547 4548 bnx2x_warpcore_config_sfi(phy, params); 4549 break; 4550 4551 case PORT_HW_CFG_NET_SERDES_IF_DXGXS: 4552 if (vars->line_speed != SPEED_20000) { 4553 DP(NETIF_MSG_LINK, "Speed not supported yet\n"); 4554 return; 4555 } 4556 DP(NETIF_MSG_LINK, "Setting 20G DXGXS\n"); 4557 bnx2x_warpcore_set_20G_DXGXS(bp, phy, lane); 4558 /* Issue Module detection */ 4559 4560 bnx2x_sfp_module_detection(phy, params); 4561 break; 4562 case PORT_HW_CFG_NET_SERDES_IF_KR2: 4563 if (!params->loopback_mode) { 4564 bnx2x_warpcore_enable_AN_KR(phy, params, vars); 4565 } else { 4566 DP(NETIF_MSG_LINK, "Setting KR 20G-Force\n"); 4567 bnx2x_warpcore_set_20G_force_KR2(phy, params); 4568 } 4569 break; 4570 default: 4571 DP(NETIF_MSG_LINK, 4572 "Unsupported Serdes Net Interface 0x%x\n", 4573 serdes_net_if); 4574 return; 4575 } 4576 } 4577 4578 /* Take lane out of reset after configuration is finished */ 4579 bnx2x_warpcore_reset_lane(bp, phy, 0); 4580 DP(NETIF_MSG_LINK, "Exit config init\n"); 4581} 4582 4583static void bnx2x_warpcore_link_reset(struct bnx2x_phy *phy, 4584 struct link_params *params) 4585{ 4586 struct bnx2x *bp = params->bp; 4587 u16 val16, lane; 4588 bnx2x_sfp_e3_set_transmitter(params, phy, 0); 4589 bnx2x_set_mdio_emac_per_phy(bp, params); 4590 bnx2x_set_aer_mmd(params, phy); 4591 /* Global register */ 4592 bnx2x_warpcore_reset_lane(bp, phy, 1); 4593 4594 /* Clear loopback settings (if any) */ 4595 /* 10G & 20G */ 4596 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4597 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 0xBFFF); 4598 4599 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4600 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0xfffe); 4601 4602 /* Update those 1-copy registers */ 4603 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 4604 MDIO_AER_BLOCK_AER_REG, 0); 4605 /* Enable 1G MDIO (1-copy) */ 4606 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4607 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL, 4608 ~0x10); 4609 4610 bnx2x_cl45_read_and_write(bp, phy, MDIO_WC_DEVAD, 4611 MDIO_WC_REG_XGXSBLK1_LANECTRL2, 0xff00); 4612 lane = bnx2x_get_warpcore_lane(phy, params); 4613 /* Disable CL36 PCS Tx */ 4614 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4615 MDIO_WC_REG_XGXSBLK1_LANECTRL0, &val16); 4616 val16 |= (0x11 << lane); 4617 if (phy->flags & FLAGS_WC_DUAL_MODE) 4618 val16 |= (0x22 << lane); 4619 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4620 MDIO_WC_REG_XGXSBLK1_LANECTRL0, val16); 4621 4622 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4623 MDIO_WC_REG_XGXSBLK1_LANECTRL1, &val16); 4624 val16 &= ~(0x0303 << (lane << 1)); 4625 val16 |= (0x0101 << (lane << 1)); 4626 if (phy->flags & FLAGS_WC_DUAL_MODE) { 4627 val16 &= ~(0x0c0c << (lane << 1)); 4628 val16 |= (0x0404 << (lane << 1)); 4629 } 4630 4631 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4632 MDIO_WC_REG_XGXSBLK1_LANECTRL1, val16); 4633 /* Restore AER */ 4634 bnx2x_set_aer_mmd(params, phy); 4635 4636} 4637 4638static void bnx2x_set_warpcore_loopback(struct bnx2x_phy *phy, 4639 struct link_params *params) 4640{ 4641 struct bnx2x *bp = params->bp; 4642 u16 val16; 4643 u32 lane; 4644 DP(NETIF_MSG_LINK, "Setting Warpcore loopback type %x, speed %d\n", 4645 params->loopback_mode, phy->req_line_speed); 4646 4647 if (phy->req_line_speed < SPEED_10000 || 4648 phy->supported & SUPPORTED_20000baseKR2_Full) { 4649 /* 10/100/1000/20G-KR2 */ 4650 4651 /* Update those 1-copy registers */ 4652 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 4653 MDIO_AER_BLOCK_AER_REG, 0); 4654 /* Enable 1G MDIO (1-copy) */ 4655 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4656 MDIO_WC_REG_XGXSBLK0_XGXSCONTROL, 4657 0x10); 4658 /* Set 1G loopback based on lane (1-copy) */ 4659 lane = bnx2x_get_warpcore_lane(phy, params); 4660 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 4661 MDIO_WC_REG_XGXSBLK1_LANECTRL2, &val16); 4662 val16 |= (1<<lane); 4663 if (phy->flags & FLAGS_WC_DUAL_MODE) 4664 val16 |= (2<<lane); 4665 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 4666 MDIO_WC_REG_XGXSBLK1_LANECTRL2, 4667 val16); 4668 4669 /* Switch back to 4-copy registers */ 4670 bnx2x_set_aer_mmd(params, phy); 4671 } else { 4672 /* 10G / 20G-DXGXS */ 4673 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4674 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 4675 0x4000); 4676 bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD, 4677 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1); 4678 } 4679} 4680 4681 4682 4683static void bnx2x_sync_link(struct link_params *params, 4684 struct link_vars *vars) 4685{ 4686 struct bnx2x *bp = params->bp; 4687 u8 link_10g_plus; 4688 if (vars->link_status & LINK_STATUS_PHYSICAL_LINK_FLAG) 4689 vars->phy_flags |= PHY_PHYSICAL_LINK_FLAG; 4690 vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP); 4691 if (vars->link_up) { 4692 DP(NETIF_MSG_LINK, "phy link up\n"); 4693 4694 vars->phy_link_up = 1; 4695 vars->duplex = DUPLEX_FULL; 4696 switch (vars->link_status & 4697 LINK_STATUS_SPEED_AND_DUPLEX_MASK) { 4698 case LINK_10THD: 4699 vars->duplex = DUPLEX_HALF; 4700 /* Fall thru */ 4701 case LINK_10TFD: 4702 vars->line_speed = SPEED_10; 4703 break; 4704 4705 case LINK_100TXHD: 4706 vars->duplex = DUPLEX_HALF; 4707 /* Fall thru */ 4708 case LINK_100T4: 4709 case LINK_100TXFD: 4710 vars->line_speed = SPEED_100; 4711 break; 4712 4713 case LINK_1000THD: 4714 vars->duplex = DUPLEX_HALF; 4715 /* Fall thru */ 4716 case LINK_1000TFD: 4717 vars->line_speed = SPEED_1000; 4718 break; 4719 4720 case LINK_2500THD: 4721 vars->duplex = DUPLEX_HALF; 4722 /* Fall thru */ 4723 case LINK_2500TFD: 4724 vars->line_speed = SPEED_2500; 4725 break; 4726 4727 case LINK_10GTFD: 4728 vars->line_speed = SPEED_10000; 4729 break; 4730 case LINK_20GTFD: 4731 vars->line_speed = SPEED_20000; 4732 break; 4733 default: 4734 break; 4735 } 4736 vars->flow_ctrl = 0; 4737 if (vars->link_status & LINK_STATUS_TX_FLOW_CONTROL_ENABLED) 4738 vars->flow_ctrl |= BNX2X_FLOW_CTRL_TX; 4739 4740 if (vars->link_status & LINK_STATUS_RX_FLOW_CONTROL_ENABLED) 4741 vars->flow_ctrl |= BNX2X_FLOW_CTRL_RX; 4742 4743 if (!vars->flow_ctrl) 4744 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 4745 4746 if (vars->line_speed && 4747 ((vars->line_speed == SPEED_10) || 4748 (vars->line_speed == SPEED_100))) { 4749 vars->phy_flags |= PHY_SGMII_FLAG; 4750 } else { 4751 vars->phy_flags &= ~PHY_SGMII_FLAG; 4752 } 4753 if (vars->line_speed && 4754 USES_WARPCORE(bp) && 4755 (vars->line_speed == SPEED_1000)) 4756 vars->phy_flags |= PHY_SGMII_FLAG; 4757 /* Anything 10 and over uses the bmac */ 4758 link_10g_plus = (vars->line_speed >= SPEED_10000); 4759 4760 if (link_10g_plus) { 4761 if (USES_WARPCORE(bp)) 4762 vars->mac_type = MAC_TYPE_XMAC; 4763 else 4764 vars->mac_type = MAC_TYPE_BMAC; 4765 } else { 4766 if (USES_WARPCORE(bp)) 4767 vars->mac_type = MAC_TYPE_UMAC; 4768 else 4769 vars->mac_type = MAC_TYPE_EMAC; 4770 } 4771 } else { /* Link down */ 4772 DP(NETIF_MSG_LINK, "phy link down\n"); 4773 4774 vars->phy_link_up = 0; 4775 4776 vars->line_speed = 0; 4777 vars->duplex = DUPLEX_FULL; 4778 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 4779 4780 /* Indicate no mac active */ 4781 vars->mac_type = MAC_TYPE_NONE; 4782 if (vars->link_status & LINK_STATUS_PHYSICAL_LINK_FLAG) 4783 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG; 4784 if (vars->link_status & LINK_STATUS_SFP_TX_FAULT) 4785 vars->phy_flags |= PHY_SFP_TX_FAULT_FLAG; 4786 } 4787} 4788 4789void bnx2x_link_status_update(struct link_params *params, 4790 struct link_vars *vars) 4791{ 4792 struct bnx2x *bp = params->bp; 4793 u8 port = params->port; 4794 u32 sync_offset, media_types; 4795 /* Update PHY configuration */ 4796 set_phy_vars(params, vars); 4797 4798 vars->link_status = REG_RD(bp, params->shmem_base + 4799 offsetof(struct shmem_region, 4800 port_mb[port].link_status)); 4801 4802 /* Force link UP in non LOOPBACK_EXT loopback mode(s) */ 4803 if (params->loopback_mode != LOOPBACK_NONE && 4804 params->loopback_mode != LOOPBACK_EXT) 4805 vars->link_status |= LINK_STATUS_LINK_UP; 4806 4807 if (bnx2x_eee_has_cap(params)) 4808 vars->eee_status = REG_RD(bp, params->shmem2_base + 4809 offsetof(struct shmem2_region, 4810 eee_status[params->port])); 4811 4812 vars->phy_flags = PHY_XGXS_FLAG; 4813 bnx2x_sync_link(params, vars); 4814 /* Sync media type */ 4815 sync_offset = params->shmem_base + 4816 offsetof(struct shmem_region, 4817 dev_info.port_hw_config[port].media_type); 4818 media_types = REG_RD(bp, sync_offset); 4819 4820 params->phy[INT_PHY].media_type = 4821 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) >> 4822 PORT_HW_CFG_MEDIA_TYPE_PHY0_SHIFT; 4823 params->phy[EXT_PHY1].media_type = 4824 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY1_MASK) >> 4825 PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT; 4826 params->phy[EXT_PHY2].media_type = 4827 (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY2_MASK) >> 4828 PORT_HW_CFG_MEDIA_TYPE_PHY2_SHIFT; 4829 DP(NETIF_MSG_LINK, "media_types = 0x%x\n", media_types); 4830 4831 /* Sync AEU offset */ 4832 sync_offset = params->shmem_base + 4833 offsetof(struct shmem_region, 4834 dev_info.port_hw_config[port].aeu_int_mask); 4835 4836 vars->aeu_int_mask = REG_RD(bp, sync_offset); 4837 4838 /* Sync PFC status */ 4839 if (vars->link_status & LINK_STATUS_PFC_ENABLED) 4840 params->feature_config_flags |= 4841 FEATURE_CONFIG_PFC_ENABLED; 4842 else 4843 params->feature_config_flags &= 4844 ~FEATURE_CONFIG_PFC_ENABLED; 4845 4846 if (SHMEM2_HAS(bp, link_attr_sync)) 4847 params->link_attr_sync = SHMEM2_RD(bp, 4848 link_attr_sync[params->port]); 4849 4850 DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x int_mask 0x%x\n", 4851 vars->link_status, vars->phy_link_up, vars->aeu_int_mask); 4852 DP(NETIF_MSG_LINK, "line_speed %x duplex %x flow_ctrl 0x%x\n", 4853 vars->line_speed, vars->duplex, vars->flow_ctrl); 4854} 4855 4856static void bnx2x_set_master_ln(struct link_params *params, 4857 struct bnx2x_phy *phy) 4858{ 4859 struct bnx2x *bp = params->bp; 4860 u16 new_master_ln, ser_lane; 4861 ser_lane = ((params->lane_config & 4862 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> 4863 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); 4864 4865 /* Set the master_ln for AN */ 4866 CL22_RD_OVER_CL45(bp, phy, 4867 MDIO_REG_BANK_XGXS_BLOCK2, 4868 MDIO_XGXS_BLOCK2_TEST_MODE_LANE, 4869 &new_master_ln); 4870 4871 CL22_WR_OVER_CL45(bp, phy, 4872 MDIO_REG_BANK_XGXS_BLOCK2 , 4873 MDIO_XGXS_BLOCK2_TEST_MODE_LANE, 4874 (new_master_ln | ser_lane)); 4875} 4876 4877static int bnx2x_reset_unicore(struct link_params *params, 4878 struct bnx2x_phy *phy, 4879 u8 set_serdes) 4880{ 4881 struct bnx2x *bp = params->bp; 4882 u16 mii_control; 4883 u16 i; 4884 CL22_RD_OVER_CL45(bp, phy, 4885 MDIO_REG_BANK_COMBO_IEEE0, 4886 MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control); 4887 4888 /* Reset the unicore */ 4889 CL22_WR_OVER_CL45(bp, phy, 4890 MDIO_REG_BANK_COMBO_IEEE0, 4891 MDIO_COMBO_IEEE0_MII_CONTROL, 4892 (mii_control | 4893 MDIO_COMBO_IEEO_MII_CONTROL_RESET)); 4894 if (set_serdes) 4895 bnx2x_set_serdes_access(bp, params->port); 4896 4897 /* Wait for the reset to self clear */ 4898 for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) { 4899 udelay(5); 4900 4901 /* The reset erased the previous bank value */ 4902 CL22_RD_OVER_CL45(bp, phy, 4903 MDIO_REG_BANK_COMBO_IEEE0, 4904 MDIO_COMBO_IEEE0_MII_CONTROL, 4905 &mii_control); 4906 4907 if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) { 4908 udelay(5); 4909 return 0; 4910 } 4911 } 4912 4913 netdev_err(bp->dev, "Warning: PHY was not initialized," 4914 " Port %d\n", 4915 params->port); 4916 DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n"); 4917 return -EINVAL; 4918 4919} 4920 4921static void bnx2x_set_swap_lanes(struct link_params *params, 4922 struct bnx2x_phy *phy) 4923{ 4924 struct bnx2x *bp = params->bp; 4925 /* Each two bits represents a lane number: 4926 * No swap is 0123 => 0x1b no need to enable the swap 4927 */ 4928 u16 rx_lane_swap, tx_lane_swap; 4929 4930 rx_lane_swap = ((params->lane_config & 4931 PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >> 4932 PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT); 4933 tx_lane_swap = ((params->lane_config & 4934 PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >> 4935 PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT); 4936 4937 if (rx_lane_swap != 0x1b) { 4938 CL22_WR_OVER_CL45(bp, phy, 4939 MDIO_REG_BANK_XGXS_BLOCK2, 4940 MDIO_XGXS_BLOCK2_RX_LN_SWAP, 4941 (rx_lane_swap | 4942 MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE | 4943 MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE)); 4944 } else { 4945 CL22_WR_OVER_CL45(bp, phy, 4946 MDIO_REG_BANK_XGXS_BLOCK2, 4947 MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0); 4948 } 4949 4950 if (tx_lane_swap != 0x1b) { 4951 CL22_WR_OVER_CL45(bp, phy, 4952 MDIO_REG_BANK_XGXS_BLOCK2, 4953 MDIO_XGXS_BLOCK2_TX_LN_SWAP, 4954 (tx_lane_swap | 4955 MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE)); 4956 } else { 4957 CL22_WR_OVER_CL45(bp, phy, 4958 MDIO_REG_BANK_XGXS_BLOCK2, 4959 MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0); 4960 } 4961} 4962 4963static void bnx2x_set_parallel_detection(struct bnx2x_phy *phy, 4964 struct link_params *params) 4965{ 4966 struct bnx2x *bp = params->bp; 4967 u16 control2; 4968 CL22_RD_OVER_CL45(bp, phy, 4969 MDIO_REG_BANK_SERDES_DIGITAL, 4970 MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, 4971 &control2); 4972 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) 4973 control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; 4974 else 4975 control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; 4976 DP(NETIF_MSG_LINK, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n", 4977 phy->speed_cap_mask, control2); 4978 CL22_WR_OVER_CL45(bp, phy, 4979 MDIO_REG_BANK_SERDES_DIGITAL, 4980 MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, 4981 control2); 4982 4983 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && 4984 (phy->speed_cap_mask & 4985 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { 4986 DP(NETIF_MSG_LINK, "XGXS\n"); 4987 4988 CL22_WR_OVER_CL45(bp, phy, 4989 MDIO_REG_BANK_10G_PARALLEL_DETECT, 4990 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK, 4991 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT); 4992 4993 CL22_RD_OVER_CL45(bp, phy, 4994 MDIO_REG_BANK_10G_PARALLEL_DETECT, 4995 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, 4996 &control2); 4997 4998 4999 control2 |= 5000 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN; 5001 5002 CL22_WR_OVER_CL45(bp, phy, 5003 MDIO_REG_BANK_10G_PARALLEL_DETECT, 5004 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, 5005 control2); 5006 5007 /* Disable parallel detection of HiG */ 5008 CL22_WR_OVER_CL45(bp, phy, 5009 MDIO_REG_BANK_XGXS_BLOCK2, 5010 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G, 5011 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS | 5012 MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS); 5013 } 5014} 5015 5016static void bnx2x_set_autoneg(struct bnx2x_phy *phy, 5017 struct link_params *params, 5018 struct link_vars *vars, 5019 u8 enable_cl73) 5020{ 5021 struct bnx2x *bp = params->bp; 5022 u16 reg_val; 5023 5024 /* CL37 Autoneg */ 5025 CL22_RD_OVER_CL45(bp, phy, 5026 MDIO_REG_BANK_COMBO_IEEE0, 5027 MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); 5028 5029 /* CL37 Autoneg Enabled */ 5030 if (vars->line_speed == SPEED_AUTO_NEG) 5031 reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN; 5032 else /* CL37 Autoneg Disabled */ 5033 reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | 5034 MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN); 5035 5036 CL22_WR_OVER_CL45(bp, phy, 5037 MDIO_REG_BANK_COMBO_IEEE0, 5038 MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); 5039 5040 /* Enable/Disable Autodetection */ 5041 5042 CL22_RD_OVER_CL45(bp, phy, 5043 MDIO_REG_BANK_SERDES_DIGITAL, 5044 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); 5045 reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN | 5046 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT); 5047 reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE; 5048 if (vars->line_speed == SPEED_AUTO_NEG) 5049 reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; 5050 else 5051 reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; 5052 5053 CL22_WR_OVER_CL45(bp, phy, 5054 MDIO_REG_BANK_SERDES_DIGITAL, 5055 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val); 5056 5057 /* Enable TetonII and BAM autoneg */ 5058 CL22_RD_OVER_CL45(bp, phy, 5059 MDIO_REG_BANK_BAM_NEXT_PAGE, 5060 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, 5061 ®_val); 5062 if (vars->line_speed == SPEED_AUTO_NEG) { 5063 /* Enable BAM aneg Mode and TetonII aneg Mode */ 5064 reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | 5065 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); 5066 } else { 5067 /* TetonII and BAM Autoneg Disabled */ 5068 reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | 5069 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); 5070 } 5071 CL22_WR_OVER_CL45(bp, phy, 5072 MDIO_REG_BANK_BAM_NEXT_PAGE, 5073 MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, 5074 reg_val); 5075 5076 if (enable_cl73) { 5077 /* Enable Cl73 FSM status bits */ 5078 CL22_WR_OVER_CL45(bp, phy, 5079 MDIO_REG_BANK_CL73_USERB0, 5080 MDIO_CL73_USERB0_CL73_UCTRL, 5081 0xe); 5082 5083 /* Enable BAM Station Manager*/ 5084 CL22_WR_OVER_CL45(bp, phy, 5085 MDIO_REG_BANK_CL73_USERB0, 5086 MDIO_CL73_USERB0_CL73_BAM_CTRL1, 5087 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN | 5088 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN | 5089 MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN); 5090 5091 /* Advertise CL73 link speeds */ 5092 CL22_RD_OVER_CL45(bp, phy, 5093 MDIO_REG_BANK_CL73_IEEEB1, 5094 MDIO_CL73_IEEEB1_AN_ADV2, 5095 ®_val); 5096 if (phy->speed_cap_mask & 5097 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) 5098 reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4; 5099 if (phy->speed_cap_mask & 5100 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) 5101 reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX; 5102 5103 CL22_WR_OVER_CL45(bp, phy, 5104 MDIO_REG_BANK_CL73_IEEEB1, 5105 MDIO_CL73_IEEEB1_AN_ADV2, 5106 reg_val); 5107 5108 /* CL73 Autoneg Enabled */ 5109 reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN; 5110 5111 } else /* CL73 Autoneg Disabled */ 5112 reg_val = 0; 5113 5114 CL22_WR_OVER_CL45(bp, phy, 5115 MDIO_REG_BANK_CL73_IEEEB0, 5116 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val); 5117} 5118 5119/* Program SerDes, forced speed */ 5120static void bnx2x_program_serdes(struct bnx2x_phy *phy, 5121 struct link_params *params, 5122 struct link_vars *vars) 5123{ 5124 struct bnx2x *bp = params->bp; 5125 u16 reg_val; 5126 5127 /* Program duplex, disable autoneg and sgmii*/ 5128 CL22_RD_OVER_CL45(bp, phy, 5129 MDIO_REG_BANK_COMBO_IEEE0, 5130 MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); 5131 reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX | 5132 MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | 5133 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK); 5134 if (phy->req_duplex == DUPLEX_FULL) 5135 reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; 5136 CL22_WR_OVER_CL45(bp, phy, 5137 MDIO_REG_BANK_COMBO_IEEE0, 5138 MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); 5139 5140 /* Program speed 5141 * - needed only if the speed is greater than 1G (2.5G or 10G) 5142 */ 5143 CL22_RD_OVER_CL45(bp, phy, 5144 MDIO_REG_BANK_SERDES_DIGITAL, 5145 MDIO_SERDES_DIGITAL_MISC1, ®_val); 5146 /* Clearing the speed value before setting the right speed */ 5147 DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); 5148 5149 reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK | 5150 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); 5151 5152 if (!((vars->line_speed == SPEED_1000) || 5153 (vars->line_speed == SPEED_100) || 5154 (vars->line_speed == SPEED_10))) { 5155 5156 reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M | 5157 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); 5158 if (vars->line_speed == SPEED_10000) 5159 reg_val |= 5160 MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4; 5161 } 5162 5163 CL22_WR_OVER_CL45(bp, phy, 5164 MDIO_REG_BANK_SERDES_DIGITAL, 5165 MDIO_SERDES_DIGITAL_MISC1, reg_val); 5166 5167} 5168 5169static void bnx2x_set_brcm_cl37_advertisement(struct bnx2x_phy *phy, 5170 struct link_params *params) 5171{ 5172 struct bnx2x *bp = params->bp; 5173 u16 val = 0; 5174 5175 /* Set extended capabilities */ 5176 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) 5177 val |= MDIO_OVER_1G_UP1_2_5G; 5178 if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) 5179 val |= MDIO_OVER_1G_UP1_10G; 5180 CL22_WR_OVER_CL45(bp, phy, 5181 MDIO_REG_BANK_OVER_1G, 5182 MDIO_OVER_1G_UP1, val); 5183 5184 CL22_WR_OVER_CL45(bp, phy, 5185 MDIO_REG_BANK_OVER_1G, 5186 MDIO_OVER_1G_UP3, 0x400); 5187} 5188 5189static void bnx2x_set_ieee_aneg_advertisement(struct bnx2x_phy *phy, 5190 struct link_params *params, 5191 u16 ieee_fc) 5192{ 5193 struct bnx2x *bp = params->bp; 5194 u16 val; 5195 /* For AN, we are always publishing full duplex */ 5196 5197 CL22_WR_OVER_CL45(bp, phy, 5198 MDIO_REG_BANK_COMBO_IEEE0, 5199 MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc); 5200 CL22_RD_OVER_CL45(bp, phy, 5201 MDIO_REG_BANK_CL73_IEEEB1, 5202 MDIO_CL73_IEEEB1_AN_ADV1, &val); 5203 val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH; 5204 val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK); 5205 CL22_WR_OVER_CL45(bp, phy, 5206 MDIO_REG_BANK_CL73_IEEEB1, 5207 MDIO_CL73_IEEEB1_AN_ADV1, val); 5208} 5209 5210static void bnx2x_restart_autoneg(struct bnx2x_phy *phy, 5211 struct link_params *params, 5212 u8 enable_cl73) 5213{ 5214 struct bnx2x *bp = params->bp; 5215 u16 mii_control; 5216 5217 DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n"); 5218 /* Enable and restart BAM/CL37 aneg */ 5219 5220 if (enable_cl73) { 5221 CL22_RD_OVER_CL45(bp, phy, 5222 MDIO_REG_BANK_CL73_IEEEB0, 5223 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, 5224 &mii_control); 5225 5226 CL22_WR_OVER_CL45(bp, phy, 5227 MDIO_REG_BANK_CL73_IEEEB0, 5228 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, 5229 (mii_control | 5230 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN | 5231 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN)); 5232 } else { 5233 5234 CL22_RD_OVER_CL45(bp, phy, 5235 MDIO_REG_BANK_COMBO_IEEE0, 5236 MDIO_COMBO_IEEE0_MII_CONTROL, 5237 &mii_control); 5238 DP(NETIF_MSG_LINK, 5239 "bnx2x_restart_autoneg mii_control before = 0x%x\n", 5240 mii_control); 5241 CL22_WR_OVER_CL45(bp, phy, 5242 MDIO_REG_BANK_COMBO_IEEE0, 5243 MDIO_COMBO_IEEE0_MII_CONTROL, 5244 (mii_control | 5245 MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | 5246 MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN)); 5247 } 5248} 5249 5250static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy, 5251 struct link_params *params, 5252 struct link_vars *vars) 5253{ 5254 struct bnx2x *bp = params->bp; 5255 u16 control1; 5256 5257 /* In SGMII mode, the unicore is always slave */ 5258 5259 CL22_RD_OVER_CL45(bp, phy, 5260 MDIO_REG_BANK_SERDES_DIGITAL, 5261 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, 5262 &control1); 5263 control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT; 5264 /* Set sgmii mode (and not fiber) */ 5265 control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE | 5266 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET | 5267 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE); 5268 CL22_WR_OVER_CL45(bp, phy, 5269 MDIO_REG_BANK_SERDES_DIGITAL, 5270 MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, 5271 control1); 5272 5273 /* If forced speed */ 5274 if (!(vars->line_speed == SPEED_AUTO_NEG)) { 5275 /* Set speed, disable autoneg */ 5276 u16 mii_control; 5277 5278 CL22_RD_OVER_CL45(bp, phy, 5279 MDIO_REG_BANK_COMBO_IEEE0, 5280 MDIO_COMBO_IEEE0_MII_CONTROL, 5281 &mii_control); 5282 mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | 5283 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| 5284 MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); 5285 5286 switch (vars->line_speed) { 5287 case SPEED_100: 5288 mii_control |= 5289 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100; 5290 break; 5291 case SPEED_1000: 5292 mii_control |= 5293 MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000; 5294 break; 5295 case SPEED_10: 5296 /* There is nothing to set for 10M */ 5297 break; 5298 default: 5299 /* Invalid speed for SGMII */ 5300 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", 5301 vars->line_speed); 5302 break; 5303 } 5304 5305 /* Setting the full duplex */ 5306 if (phy->req_duplex == DUPLEX_FULL) 5307 mii_control |= 5308 MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; 5309 CL22_WR_OVER_CL45(bp, phy, 5310 MDIO_REG_BANK_COMBO_IEEE0, 5311 MDIO_COMBO_IEEE0_MII_CONTROL, 5312 mii_control); 5313 5314 } else { /* AN mode */ 5315 /* Enable and restart AN */ 5316 bnx2x_restart_autoneg(phy, params, 0); 5317 } 5318} 5319 5320/* Link management 5321 */ 5322static int bnx2x_direct_parallel_detect_used(struct bnx2x_phy *phy, 5323 struct link_params *params) 5324{ 5325 struct bnx2x *bp = params->bp; 5326 u16 pd_10g, status2_1000x; 5327 if (phy->req_line_speed != SPEED_AUTO_NEG) 5328 return 0; 5329 CL22_RD_OVER_CL45(bp, phy, 5330 MDIO_REG_BANK_SERDES_DIGITAL, 5331 MDIO_SERDES_DIGITAL_A_1000X_STATUS2, 5332 &status2_1000x); 5333 CL22_RD_OVER_CL45(bp, phy, 5334 MDIO_REG_BANK_SERDES_DIGITAL, 5335 MDIO_SERDES_DIGITAL_A_1000X_STATUS2, 5336 &status2_1000x); 5337 if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) { 5338 DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n", 5339 params->port); 5340 return 1; 5341 } 5342 5343 CL22_RD_OVER_CL45(bp, phy, 5344 MDIO_REG_BANK_10G_PARALLEL_DETECT, 5345 MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS, 5346 &pd_10g); 5347 5348 if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) { 5349 DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n", 5350 params->port); 5351 return 1; 5352 } 5353 return 0; 5354} 5355 5356static void bnx2x_update_adv_fc(struct bnx2x_phy *phy, 5357 struct link_params *params, 5358 struct link_vars *vars, 5359 u32 gp_status) 5360{ 5361 u16 ld_pause; /* local driver */ 5362 u16 lp_pause; /* link partner */ 5363 u16 pause_result; 5364 struct bnx2x *bp = params->bp; 5365 if ((gp_status & 5366 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | 5367 MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) == 5368 (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | 5369 MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) { 5370 5371 CL22_RD_OVER_CL45(bp, phy, 5372 MDIO_REG_BANK_CL73_IEEEB1, 5373 MDIO_CL73_IEEEB1_AN_ADV1, 5374 &ld_pause); 5375 CL22_RD_OVER_CL45(bp, phy, 5376 MDIO_REG_BANK_CL73_IEEEB1, 5377 MDIO_CL73_IEEEB1_AN_LP_ADV1, 5378 &lp_pause); 5379 pause_result = (ld_pause & 5380 MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK) >> 8; 5381 pause_result |= (lp_pause & 5382 MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK) >> 10; 5383 DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n", pause_result); 5384 } else { 5385 CL22_RD_OVER_CL45(bp, phy, 5386 MDIO_REG_BANK_COMBO_IEEE0, 5387 MDIO_COMBO_IEEE0_AUTO_NEG_ADV, 5388 &ld_pause); 5389 CL22_RD_OVER_CL45(bp, phy, 5390 MDIO_REG_BANK_COMBO_IEEE0, 5391 MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1, 5392 &lp_pause); 5393 pause_result = (ld_pause & 5394 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5; 5395 pause_result |= (lp_pause & 5396 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7; 5397 DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n", pause_result); 5398 } 5399 bnx2x_pause_resolve(vars, pause_result); 5400 5401} 5402 5403static void bnx2x_flow_ctrl_resolve(struct bnx2x_phy *phy, 5404 struct link_params *params, 5405 struct link_vars *vars, 5406 u32 gp_status) 5407{ 5408 struct bnx2x *bp = params->bp; 5409 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 5410 5411 /* Resolve from gp_status in case of AN complete and not sgmii */ 5412 if (phy->req_flow_ctrl != BNX2X_FLOW_CTRL_AUTO) { 5413 /* Update the advertised flow-controled of LD/LP in AN */ 5414 if (phy->req_line_speed == SPEED_AUTO_NEG) 5415 bnx2x_update_adv_fc(phy, params, vars, gp_status); 5416 /* But set the flow-control result as the requested one */ 5417 vars->flow_ctrl = phy->req_flow_ctrl; 5418 } else if (phy->req_line_speed != SPEED_AUTO_NEG) 5419 vars->flow_ctrl = params->req_fc_auto_adv; 5420 else if ((gp_status & MDIO_AN_CL73_OR_37_COMPLETE) && 5421 (!(vars->phy_flags & PHY_SGMII_FLAG))) { 5422 if (bnx2x_direct_parallel_detect_used(phy, params)) { 5423 vars->flow_ctrl = params->req_fc_auto_adv; 5424 return; 5425 } 5426 bnx2x_update_adv_fc(phy, params, vars, gp_status); 5427 } 5428 DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl); 5429} 5430 5431static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy, 5432 struct link_params *params) 5433{ 5434 struct bnx2x *bp = params->bp; 5435 u16 rx_status, ustat_val, cl37_fsm_received; 5436 DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n"); 5437 /* Step 1: Make sure signal is detected */ 5438 CL22_RD_OVER_CL45(bp, phy, 5439 MDIO_REG_BANK_RX0, 5440 MDIO_RX0_RX_STATUS, 5441 &rx_status); 5442 if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) != 5443 (MDIO_RX0_RX_STATUS_SIGDET)) { 5444 DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73." 5445 "rx_status(0x80b0) = 0x%x\n", rx_status); 5446 CL22_WR_OVER_CL45(bp, phy, 5447 MDIO_REG_BANK_CL73_IEEEB0, 5448 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, 5449 MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN); 5450 return; 5451 } 5452 /* Step 2: Check CL73 state machine */ 5453 CL22_RD_OVER_CL45(bp, phy, 5454 MDIO_REG_BANK_CL73_USERB0, 5455 MDIO_CL73_USERB0_CL73_USTAT1, 5456 &ustat_val); 5457 if ((ustat_val & 5458 (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK | 5459 MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) != 5460 (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK | 5461 MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) { 5462 DP(NETIF_MSG_LINK, "CL73 state-machine is not stable. " 5463 "ustat_val(0x8371) = 0x%x\n", ustat_val); 5464 return; 5465 } 5466 /* Step 3: Check CL37 Message Pages received to indicate LP 5467 * supports only CL37 5468 */ 5469 CL22_RD_OVER_CL45(bp, phy, 5470 MDIO_REG_BANK_REMOTE_PHY, 5471 MDIO_REMOTE_PHY_MISC_RX_STATUS, 5472 &cl37_fsm_received); 5473 if ((cl37_fsm_received & 5474 (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG | 5475 MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) != 5476 (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG | 5477 MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) { 5478 DP(NETIF_MSG_LINK, "No CL37 FSM were received. " 5479 "misc_rx_status(0x8330) = 0x%x\n", 5480 cl37_fsm_received); 5481 return; 5482 } 5483 /* The combined cl37/cl73 fsm state information indicating that 5484 * we are connected to a device which does not support cl73, but 5485 * does support cl37 BAM. In this case we disable cl73 and 5486 * restart cl37 auto-neg 5487 */ 5488 5489 /* Disable CL73 */ 5490 CL22_WR_OVER_CL45(bp, phy, 5491 MDIO_REG_BANK_CL73_IEEEB0, 5492 MDIO_CL73_IEEEB0_CL73_AN_CONTROL, 5493 0); 5494 /* Restart CL37 autoneg */ 5495 bnx2x_restart_autoneg(phy, params, 0); 5496 DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n"); 5497} 5498 5499static void bnx2x_xgxs_an_resolve(struct bnx2x_phy *phy, 5500 struct link_params *params, 5501 struct link_vars *vars, 5502 u32 gp_status) 5503{ 5504 if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) 5505 vars->link_status |= 5506 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; 5507 5508 if (bnx2x_direct_parallel_detect_used(phy, params)) 5509 vars->link_status |= 5510 LINK_STATUS_PARALLEL_DETECTION_USED; 5511} 5512static int bnx2x_get_link_speed_duplex(struct bnx2x_phy *phy, 5513 struct link_params *params, 5514 struct link_vars *vars, 5515 u16 is_link_up, 5516 u16 speed_mask, 5517 u16 is_duplex) 5518{ 5519 struct bnx2x *bp = params->bp; 5520 if (phy->req_line_speed == SPEED_AUTO_NEG) 5521 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED; 5522 if (is_link_up) { 5523 DP(NETIF_MSG_LINK, "phy link up\n"); 5524 5525 vars->phy_link_up = 1; 5526 vars->link_status |= LINK_STATUS_LINK_UP; 5527 5528 switch (speed_mask) { 5529 case GP_STATUS_10M: 5530 vars->line_speed = SPEED_10; 5531 if (is_duplex == DUPLEX_FULL) 5532 vars->link_status |= LINK_10TFD; 5533 else 5534 vars->link_status |= LINK_10THD; 5535 break; 5536 5537 case GP_STATUS_100M: 5538 vars->line_speed = SPEED_100; 5539 if (is_duplex == DUPLEX_FULL) 5540 vars->link_status |= LINK_100TXFD; 5541 else 5542 vars->link_status |= LINK_100TXHD; 5543 break; 5544 5545 case GP_STATUS_1G: 5546 case GP_STATUS_1G_KX: 5547 vars->line_speed = SPEED_1000; 5548 if (is_duplex == DUPLEX_FULL) 5549 vars->link_status |= LINK_1000TFD; 5550 else 5551 vars->link_status |= LINK_1000THD; 5552 break; 5553 5554 case GP_STATUS_2_5G: 5555 vars->line_speed = SPEED_2500; 5556 if (is_duplex == DUPLEX_FULL) 5557 vars->link_status |= LINK_2500TFD; 5558 else 5559 vars->link_status |= LINK_2500THD; 5560 break; 5561 5562 case GP_STATUS_5G: 5563 case GP_STATUS_6G: 5564 DP(NETIF_MSG_LINK, 5565 "link speed unsupported gp_status 0x%x\n", 5566 speed_mask); 5567 return -EINVAL; 5568 5569 case GP_STATUS_10G_KX4: 5570 case GP_STATUS_10G_HIG: 5571 case GP_STATUS_10G_CX4: 5572 case GP_STATUS_10G_KR: 5573 case GP_STATUS_10G_SFI: 5574 case GP_STATUS_10G_XFI: 5575 vars->line_speed = SPEED_10000; 5576 vars->link_status |= LINK_10GTFD; 5577 break; 5578 case GP_STATUS_20G_DXGXS: 5579 case GP_STATUS_20G_KR2: 5580 vars->line_speed = SPEED_20000; 5581 vars->link_status |= LINK_20GTFD; 5582 break; 5583 default: 5584 DP(NETIF_MSG_LINK, 5585 "link speed unsupported gp_status 0x%x\n", 5586 speed_mask); 5587 return -EINVAL; 5588 } 5589 } else { /* link_down */ 5590 DP(NETIF_MSG_LINK, "phy link down\n"); 5591 5592 vars->phy_link_up = 0; 5593 5594 vars->duplex = DUPLEX_FULL; 5595 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 5596 vars->mac_type = MAC_TYPE_NONE; 5597 } 5598 DP(NETIF_MSG_LINK, " phy_link_up %x line_speed %d\n", 5599 vars->phy_link_up, vars->line_speed); 5600 return 0; 5601} 5602 5603static int bnx2x_link_settings_status(struct bnx2x_phy *phy, 5604 struct link_params *params, 5605 struct link_vars *vars) 5606{ 5607 struct bnx2x *bp = params->bp; 5608 5609 u16 gp_status, duplex = DUPLEX_HALF, link_up = 0, speed_mask; 5610 int rc = 0; 5611 5612 /* Read gp_status */ 5613 CL22_RD_OVER_CL45(bp, phy, 5614 MDIO_REG_BANK_GP_STATUS, 5615 MDIO_GP_STATUS_TOP_AN_STATUS1, 5616 &gp_status); 5617 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS) 5618 duplex = DUPLEX_FULL; 5619 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) 5620 link_up = 1; 5621 speed_mask = gp_status & GP_STATUS_SPEED_MASK; 5622 DP(NETIF_MSG_LINK, "gp_status 0x%x, is_link_up %d, speed_mask 0x%x\n", 5623 gp_status, link_up, speed_mask); 5624 rc = bnx2x_get_link_speed_duplex(phy, params, vars, link_up, speed_mask, 5625 duplex); 5626 if (rc == -EINVAL) 5627 return rc; 5628 5629 if (gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS) { 5630 if (SINGLE_MEDIA_DIRECT(params)) { 5631 vars->duplex = duplex; 5632 bnx2x_flow_ctrl_resolve(phy, params, vars, gp_status); 5633 if (phy->req_line_speed == SPEED_AUTO_NEG) 5634 bnx2x_xgxs_an_resolve(phy, params, vars, 5635 gp_status); 5636 } 5637 } else { /* Link_down */ 5638 if ((phy->req_line_speed == SPEED_AUTO_NEG) && 5639 SINGLE_MEDIA_DIRECT(params)) { 5640 /* Check signal is detected */ 5641 bnx2x_check_fallback_to_cl37(phy, params); 5642 } 5643 } 5644 5645 /* Read LP advertised speeds*/ 5646 if (SINGLE_MEDIA_DIRECT(params) && 5647 (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE)) { 5648 u16 val; 5649 5650 CL22_RD_OVER_CL45(bp, phy, MDIO_REG_BANK_CL73_IEEEB1, 5651 MDIO_CL73_IEEEB1_AN_LP_ADV2, &val); 5652 5653 if (val & MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX) 5654 vars->link_status |= 5655 LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE; 5656 if (val & (MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 | 5657 MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KR)) 5658 vars->link_status |= 5659 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 5660 5661 CL22_RD_OVER_CL45(bp, phy, MDIO_REG_BANK_OVER_1G, 5662 MDIO_OVER_1G_LP_UP1, &val); 5663 5664 if (val & MDIO_OVER_1G_UP1_2_5G) 5665 vars->link_status |= 5666 LINK_STATUS_LINK_PARTNER_2500XFD_CAPABLE; 5667 if (val & (MDIO_OVER_1G_UP1_10G | MDIO_OVER_1G_UP1_10GH)) 5668 vars->link_status |= 5669 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 5670 } 5671 5672 DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x link_status 0x%x\n", 5673 vars->duplex, vars->flow_ctrl, vars->link_status); 5674 return rc; 5675} 5676 5677static int bnx2x_warpcore_read_status(struct bnx2x_phy *phy, 5678 struct link_params *params, 5679 struct link_vars *vars) 5680{ 5681 struct bnx2x *bp = params->bp; 5682 u8 lane; 5683 u16 gp_status1, gp_speed, link_up, duplex = DUPLEX_FULL; 5684 int rc = 0; 5685 lane = bnx2x_get_warpcore_lane(phy, params); 5686 /* Read gp_status */ 5687 if ((params->loopback_mode) && 5688 (phy->flags & FLAGS_WC_DUAL_MODE)) { 5689 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5690 MDIO_WC_REG_DIGITAL5_LINK_STATUS, &link_up); 5691 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5692 MDIO_WC_REG_DIGITAL5_LINK_STATUS, &link_up); 5693 link_up &= 0x1; 5694 } else if ((phy->req_line_speed > SPEED_10000) && 5695 (phy->supported & SUPPORTED_20000baseMLD2_Full)) { 5696 u16 temp_link_up; 5697 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5698 1, &temp_link_up); 5699 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5700 1, &link_up); 5701 DP(NETIF_MSG_LINK, "PCS RX link status = 0x%x-->0x%x\n", 5702 temp_link_up, link_up); 5703 link_up &= (1<<2); 5704 if (link_up) 5705 bnx2x_ext_phy_resolve_fc(phy, params, vars); 5706 } else { 5707 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5708 MDIO_WC_REG_GP2_STATUS_GP_2_1, 5709 &gp_status1); 5710 DP(NETIF_MSG_LINK, "0x81d1 = 0x%x\n", gp_status1); 5711 /* Check for either KR, 1G, or AN up. */ 5712 link_up = ((gp_status1 >> 8) | 5713 (gp_status1 >> 12) | 5714 (gp_status1)) & 5715 (1 << lane); 5716 if (phy->supported & SUPPORTED_20000baseKR2_Full) { 5717 u16 an_link; 5718 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 5719 MDIO_AN_REG_STATUS, &an_link); 5720 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 5721 MDIO_AN_REG_STATUS, &an_link); 5722 link_up |= (an_link & (1<<2)); 5723 } 5724 if (link_up && SINGLE_MEDIA_DIRECT(params)) { 5725 u16 pd, gp_status4; 5726 if (phy->req_line_speed == SPEED_AUTO_NEG) { 5727 /* Check Autoneg complete */ 5728 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5729 MDIO_WC_REG_GP2_STATUS_GP_2_4, 5730 &gp_status4); 5731 if (gp_status4 & ((1<<12)<<lane)) 5732 vars->link_status |= 5733 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; 5734 5735 /* Check parallel detect used */ 5736 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5737 MDIO_WC_REG_PAR_DET_10G_STATUS, 5738 &pd); 5739 if (pd & (1<<15)) 5740 vars->link_status |= 5741 LINK_STATUS_PARALLEL_DETECTION_USED; 5742 } 5743 bnx2x_ext_phy_resolve_fc(phy, params, vars); 5744 vars->duplex = duplex; 5745 } 5746 } 5747 5748 if ((vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) && 5749 SINGLE_MEDIA_DIRECT(params)) { 5750 u16 val; 5751 5752 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 5753 MDIO_AN_REG_LP_AUTO_NEG2, &val); 5754 5755 if (val & MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX) 5756 vars->link_status |= 5757 LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE; 5758 if (val & (MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 | 5759 MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KR)) 5760 vars->link_status |= 5761 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 5762 5763 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5764 MDIO_WC_REG_DIGITAL3_LP_UP1, &val); 5765 5766 if (val & MDIO_OVER_1G_UP1_2_5G) 5767 vars->link_status |= 5768 LINK_STATUS_LINK_PARTNER_2500XFD_CAPABLE; 5769 if (val & (MDIO_OVER_1G_UP1_10G | MDIO_OVER_1G_UP1_10GH)) 5770 vars->link_status |= 5771 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 5772 5773 } 5774 5775 5776 if (lane < 2) { 5777 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5778 MDIO_WC_REG_GP2_STATUS_GP_2_2, &gp_speed); 5779 } else { 5780 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 5781 MDIO_WC_REG_GP2_STATUS_GP_2_3, &gp_speed); 5782 } 5783 DP(NETIF_MSG_LINK, "lane %d gp_speed 0x%x\n", lane, gp_speed); 5784 5785 if ((lane & 1) == 0) 5786 gp_speed <<= 8; 5787 gp_speed &= 0x3f00; 5788 link_up = !!link_up; 5789 5790 rc = bnx2x_get_link_speed_duplex(phy, params, vars, link_up, gp_speed, 5791 duplex); 5792 5793 /* In case of KR link down, start up the recovering procedure */ 5794 if ((!link_up) && (phy->media_type == ETH_PHY_KR) && 5795 (!(phy->flags & FLAGS_WC_DUAL_MODE))) 5796 vars->rx_tx_asic_rst = MAX_KR_LINK_RETRY; 5797 5798 DP(NETIF_MSG_LINK, "duplex %x flow_ctrl 0x%x link_status 0x%x\n", 5799 vars->duplex, vars->flow_ctrl, vars->link_status); 5800 return rc; 5801} 5802static void bnx2x_set_gmii_tx_driver(struct link_params *params) 5803{ 5804 struct bnx2x *bp = params->bp; 5805 struct bnx2x_phy *phy = ¶ms->phy[INT_PHY]; 5806 u16 lp_up2; 5807 u16 tx_driver; 5808 u16 bank; 5809 5810 /* Read precomp */ 5811 CL22_RD_OVER_CL45(bp, phy, 5812 MDIO_REG_BANK_OVER_1G, 5813 MDIO_OVER_1G_LP_UP2, &lp_up2); 5814 5815 /* Bits [10:7] at lp_up2, positioned at [15:12] */ 5816 lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >> 5817 MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) << 5818 MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT); 5819 5820 if (lp_up2 == 0) 5821 return; 5822 5823 for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3; 5824 bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) { 5825 CL22_RD_OVER_CL45(bp, phy, 5826 bank, 5827 MDIO_TX0_TX_DRIVER, &tx_driver); 5828 5829 /* Replace tx_driver bits [15:12] */ 5830 if (lp_up2 != 5831 (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) { 5832 tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK; 5833 tx_driver |= lp_up2; 5834 CL22_WR_OVER_CL45(bp, phy, 5835 bank, 5836 MDIO_TX0_TX_DRIVER, tx_driver); 5837 } 5838 } 5839} 5840 5841static int bnx2x_emac_program(struct link_params *params, 5842 struct link_vars *vars) 5843{ 5844 struct bnx2x *bp = params->bp; 5845 u8 port = params->port; 5846 u16 mode = 0; 5847 5848 DP(NETIF_MSG_LINK, "setting link speed & duplex\n"); 5849 bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 + 5850 EMAC_REG_EMAC_MODE, 5851 (EMAC_MODE_25G_MODE | 5852 EMAC_MODE_PORT_MII_10M | 5853 EMAC_MODE_HALF_DUPLEX)); 5854 switch (vars->line_speed) { 5855 case SPEED_10: 5856 mode |= EMAC_MODE_PORT_MII_10M; 5857 break; 5858 5859 case SPEED_100: 5860 mode |= EMAC_MODE_PORT_MII; 5861 break; 5862 5863 case SPEED_1000: 5864 mode |= EMAC_MODE_PORT_GMII; 5865 break; 5866 5867 case SPEED_2500: 5868 mode |= (EMAC_MODE_25G_MODE | EMAC_MODE_PORT_GMII); 5869 break; 5870 5871 default: 5872 /* 10G not valid for EMAC */ 5873 DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", 5874 vars->line_speed); 5875 return -EINVAL; 5876 } 5877 5878 if (vars->duplex == DUPLEX_HALF) 5879 mode |= EMAC_MODE_HALF_DUPLEX; 5880 bnx2x_bits_en(bp, 5881 GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE, 5882 mode); 5883 5884 bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed); 5885 return 0; 5886} 5887 5888static void bnx2x_set_preemphasis(struct bnx2x_phy *phy, 5889 struct link_params *params) 5890{ 5891 5892 u16 bank, i = 0; 5893 struct bnx2x *bp = params->bp; 5894 5895 for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3; 5896 bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) { 5897 CL22_WR_OVER_CL45(bp, phy, 5898 bank, 5899 MDIO_RX0_RX_EQ_BOOST, 5900 phy->rx_preemphasis[i]); 5901 } 5902 5903 for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3; 5904 bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) { 5905 CL22_WR_OVER_CL45(bp, phy, 5906 bank, 5907 MDIO_TX0_TX_DRIVER, 5908 phy->tx_preemphasis[i]); 5909 } 5910} 5911 5912static void bnx2x_xgxs_config_init(struct bnx2x_phy *phy, 5913 struct link_params *params, 5914 struct link_vars *vars) 5915{ 5916 struct bnx2x *bp = params->bp; 5917 u8 enable_cl73 = (SINGLE_MEDIA_DIRECT(params) || 5918 (params->loopback_mode == LOOPBACK_XGXS)); 5919 if (!(vars->phy_flags & PHY_SGMII_FLAG)) { 5920 if (SINGLE_MEDIA_DIRECT(params) && 5921 (params->feature_config_flags & 5922 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) 5923 bnx2x_set_preemphasis(phy, params); 5924 5925 /* Forced speed requested? */ 5926 if (vars->line_speed != SPEED_AUTO_NEG || 5927 (SINGLE_MEDIA_DIRECT(params) && 5928 params->loopback_mode == LOOPBACK_EXT)) { 5929 DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); 5930 5931 /* Disable autoneg */ 5932 bnx2x_set_autoneg(phy, params, vars, 0); 5933 5934 /* Program speed and duplex */ 5935 bnx2x_program_serdes(phy, params, vars); 5936 5937 } else { /* AN_mode */ 5938 DP(NETIF_MSG_LINK, "not SGMII, AN\n"); 5939 5940 /* AN enabled */ 5941 bnx2x_set_brcm_cl37_advertisement(phy, params); 5942 5943 /* Program duplex & pause advertisement (for aneg) */ 5944 bnx2x_set_ieee_aneg_advertisement(phy, params, 5945 vars->ieee_fc); 5946 5947 /* Enable autoneg */ 5948 bnx2x_set_autoneg(phy, params, vars, enable_cl73); 5949 5950 /* Enable and restart AN */ 5951 bnx2x_restart_autoneg(phy, params, enable_cl73); 5952 } 5953 5954 } else { /* SGMII mode */ 5955 DP(NETIF_MSG_LINK, "SGMII\n"); 5956 5957 bnx2x_initialize_sgmii_process(phy, params, vars); 5958 } 5959} 5960 5961static int bnx2x_prepare_xgxs(struct bnx2x_phy *phy, 5962 struct link_params *params, 5963 struct link_vars *vars) 5964{ 5965 int rc; 5966 vars->phy_flags |= PHY_XGXS_FLAG; 5967 if ((phy->req_line_speed && 5968 ((phy->req_line_speed == SPEED_100) || 5969 (phy->req_line_speed == SPEED_10))) || 5970 (!phy->req_line_speed && 5971 (phy->speed_cap_mask >= 5972 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) && 5973 (phy->speed_cap_mask < 5974 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || 5975 (phy->type == PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT_SD)) 5976 vars->phy_flags |= PHY_SGMII_FLAG; 5977 else 5978 vars->phy_flags &= ~PHY_SGMII_FLAG; 5979 5980 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc); 5981 bnx2x_set_aer_mmd(params, phy); 5982 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) 5983 bnx2x_set_master_ln(params, phy); 5984 5985 rc = bnx2x_reset_unicore(params, phy, 0); 5986 /* Reset the SerDes and wait for reset bit return low */ 5987 if (rc) 5988 return rc; 5989 5990 bnx2x_set_aer_mmd(params, phy); 5991 /* Setting the masterLn_def again after the reset */ 5992 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) { 5993 bnx2x_set_master_ln(params, phy); 5994 bnx2x_set_swap_lanes(params, phy); 5995 } 5996 5997 return rc; 5998} 5999 6000static u16 bnx2x_wait_reset_complete(struct bnx2x *bp, 6001 struct bnx2x_phy *phy, 6002 struct link_params *params) 6003{ 6004 u16 cnt, ctrl; 6005 /* Wait for soft reset to get cleared up to 1 sec */ 6006 for (cnt = 0; cnt < 1000; cnt++) { 6007 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) 6008 bnx2x_cl22_read(bp, phy, 6009 MDIO_PMA_REG_CTRL, &ctrl); 6010 else 6011 bnx2x_cl45_read(bp, phy, 6012 MDIO_PMA_DEVAD, 6013 MDIO_PMA_REG_CTRL, &ctrl); 6014 if (!(ctrl & (1<<15))) 6015 break; 6016 usleep_range(1000, 2000); 6017 } 6018 6019 if (cnt == 1000) 6020 netdev_err(bp->dev, "Warning: PHY was not initialized," 6021 " Port %d\n", 6022 params->port); 6023 DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n", ctrl, cnt); 6024 return cnt; 6025} 6026 6027static void bnx2x_link_int_enable(struct link_params *params) 6028{ 6029 u8 port = params->port; 6030 u32 mask; 6031 struct bnx2x *bp = params->bp; 6032 6033 /* Setting the status to report on link up for either XGXS or SerDes */ 6034 if (CHIP_IS_E3(bp)) { 6035 mask = NIG_MASK_XGXS0_LINK_STATUS; 6036 if (!(SINGLE_MEDIA_DIRECT(params))) 6037 mask |= NIG_MASK_MI_INT; 6038 } else if (params->switch_cfg == SWITCH_CFG_10G) { 6039 mask = (NIG_MASK_XGXS0_LINK10G | 6040 NIG_MASK_XGXS0_LINK_STATUS); 6041 DP(NETIF_MSG_LINK, "enabled XGXS interrupt\n"); 6042 if (!(SINGLE_MEDIA_DIRECT(params)) && 6043 params->phy[INT_PHY].type != 6044 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE) { 6045 mask |= NIG_MASK_MI_INT; 6046 DP(NETIF_MSG_LINK, "enabled external phy int\n"); 6047 } 6048 6049 } else { /* SerDes */ 6050 mask = NIG_MASK_SERDES0_LINK_STATUS; 6051 DP(NETIF_MSG_LINK, "enabled SerDes interrupt\n"); 6052 if (!(SINGLE_MEDIA_DIRECT(params)) && 6053 params->phy[INT_PHY].type != 6054 PORT_HW_CFG_SERDES_EXT_PHY_TYPE_NOT_CONN) { 6055 mask |= NIG_MASK_MI_INT; 6056 DP(NETIF_MSG_LINK, "enabled external phy int\n"); 6057 } 6058 } 6059 bnx2x_bits_en(bp, 6060 NIG_REG_MASK_INTERRUPT_PORT0 + port*4, 6061 mask); 6062 6063 DP(NETIF_MSG_LINK, "port %x, is_xgxs %x, int_status 0x%x\n", port, 6064 (params->switch_cfg == SWITCH_CFG_10G), 6065 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4)); 6066 DP(NETIF_MSG_LINK, " int_mask 0x%x, MI_INT %x, SERDES_LINK %x\n", 6067 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), 6068 REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18), 6069 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS+port*0x3c)); 6070 DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n", 6071 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), 6072 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); 6073} 6074 6075static void bnx2x_rearm_latch_signal(struct bnx2x *bp, u8 port, 6076 u8 exp_mi_int) 6077{ 6078 u32 latch_status = 0; 6079 6080 /* Disable the MI INT ( external phy int ) by writing 1 to the 6081 * status register. Link down indication is high-active-signal, 6082 * so in this case we need to write the status to clear the XOR 6083 */ 6084 /* Read Latched signals */ 6085 latch_status = REG_RD(bp, 6086 NIG_REG_LATCH_STATUS_0 + port*8); 6087 DP(NETIF_MSG_LINK, "latch_status = 0x%x\n", latch_status); 6088 /* Handle only those with latched-signal=up.*/ 6089 if (exp_mi_int) 6090 bnx2x_bits_en(bp, 6091 NIG_REG_STATUS_INTERRUPT_PORT0 6092 + port*4, 6093 NIG_STATUS_EMAC0_MI_INT); 6094 else 6095 bnx2x_bits_dis(bp, 6096 NIG_REG_STATUS_INTERRUPT_PORT0 6097 + port*4, 6098 NIG_STATUS_EMAC0_MI_INT); 6099 6100 if (latch_status & 1) { 6101 6102 /* For all latched-signal=up : Re-Arm Latch signals */ 6103 REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8, 6104 (latch_status & 0xfffe) | (latch_status & 1)); 6105 } 6106 /* For all latched-signal=up,Write original_signal to status */ 6107} 6108 6109static void bnx2x_link_int_ack(struct link_params *params, 6110 struct link_vars *vars, u8 is_10g_plus) 6111{ 6112 struct bnx2x *bp = params->bp; 6113 u8 port = params->port; 6114 u32 mask; 6115 /* First reset all status we assume only one line will be 6116 * change at a time 6117 */ 6118 bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, 6119 (NIG_STATUS_XGXS0_LINK10G | 6120 NIG_STATUS_XGXS0_LINK_STATUS | 6121 NIG_STATUS_SERDES0_LINK_STATUS)); 6122 if (vars->phy_link_up) { 6123 if (USES_WARPCORE(bp)) 6124 mask = NIG_STATUS_XGXS0_LINK_STATUS; 6125 else { 6126 if (is_10g_plus) 6127 mask = NIG_STATUS_XGXS0_LINK10G; 6128 else if (params->switch_cfg == SWITCH_CFG_10G) { 6129 /* Disable the link interrupt by writing 1 to 6130 * the relevant lane in the status register 6131 */ 6132 u32 ser_lane = 6133 ((params->lane_config & 6134 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> 6135 PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); 6136 mask = ((1 << ser_lane) << 6137 NIG_STATUS_XGXS0_LINK_STATUS_SIZE); 6138 } else 6139 mask = NIG_STATUS_SERDES0_LINK_STATUS; 6140 } 6141 DP(NETIF_MSG_LINK, "Ack link up interrupt with mask 0x%x\n", 6142 mask); 6143 bnx2x_bits_en(bp, 6144 NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, 6145 mask); 6146 } 6147} 6148 6149static int bnx2x_format_ver(u32 num, u8 *str, u16 *len) 6150{ 6151 u8 *str_ptr = str; 6152 u32 mask = 0xf0000000; 6153 u8 shift = 8*4; 6154 u8 digit; 6155 u8 remove_leading_zeros = 1; 6156 if (*len < 10) { 6157 /* Need more than 10chars for this format */ 6158 *str_ptr = '\0'; 6159 (*len)--; 6160 return -EINVAL; 6161 } 6162 while (shift > 0) { 6163 6164 shift -= 4; 6165 digit = ((num & mask) >> shift); 6166 if (digit == 0 && remove_leading_zeros) { 6167 mask = mask >> 4; 6168 continue; 6169 } else if (digit < 0xa) 6170 *str_ptr = digit + '0'; 6171 else 6172 *str_ptr = digit - 0xa + 'a'; 6173 remove_leading_zeros = 0; 6174 str_ptr++; 6175 (*len)--; 6176 mask = mask >> 4; 6177 if (shift == 4*4) { 6178 *str_ptr = '.'; 6179 str_ptr++; 6180 (*len)--; 6181 remove_leading_zeros = 1; 6182 } 6183 } 6184 return 0; 6185} 6186 6187 6188static int bnx2x_null_format_ver(u32 spirom_ver, u8 *str, u16 *len) 6189{ 6190 str[0] = '\0'; 6191 (*len)--; 6192 return 0; 6193} 6194 6195int bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 *version, 6196 u16 len) 6197{ 6198 struct bnx2x *bp; 6199 u32 spirom_ver = 0; 6200 int status = 0; 6201 u8 *ver_p = version; 6202 u16 remain_len = len; 6203 if (version == NULL || params == NULL) 6204 return -EINVAL; 6205 bp = params->bp; 6206 6207 /* Extract first external phy*/ 6208 version[0] = '\0'; 6209 spirom_ver = REG_RD(bp, params->phy[EXT_PHY1].ver_addr); 6210 6211 if (params->phy[EXT_PHY1].format_fw_ver) { 6212 status |= params->phy[EXT_PHY1].format_fw_ver(spirom_ver, 6213 ver_p, 6214 &remain_len); 6215 ver_p += (len - remain_len); 6216 } 6217 if ((params->num_phys == MAX_PHYS) && 6218 (params->phy[EXT_PHY2].ver_addr != 0)) { 6219 spirom_ver = REG_RD(bp, params->phy[EXT_PHY2].ver_addr); 6220 if (params->phy[EXT_PHY2].format_fw_ver) { 6221 *ver_p = '/'; 6222 ver_p++; 6223 remain_len--; 6224 status |= params->phy[EXT_PHY2].format_fw_ver( 6225 spirom_ver, 6226 ver_p, 6227 &remain_len); 6228 ver_p = version + (len - remain_len); 6229 } 6230 } 6231 *ver_p = '\0'; 6232 return status; 6233} 6234 6235static void bnx2x_set_xgxs_loopback(struct bnx2x_phy *phy, 6236 struct link_params *params) 6237{ 6238 u8 port = params->port; 6239 struct bnx2x *bp = params->bp; 6240 6241 if (phy->req_line_speed != SPEED_1000) { 6242 u32 md_devad = 0; 6243 6244 DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n"); 6245 6246 if (!CHIP_IS_E3(bp)) { 6247 /* Change the uni_phy_addr in the nig */ 6248 md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD + 6249 port*0x18)); 6250 6251 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 6252 0x5); 6253 } 6254 6255 bnx2x_cl45_write(bp, phy, 6256 5, 6257 (MDIO_REG_BANK_AER_BLOCK + 6258 (MDIO_AER_BLOCK_AER_REG & 0xf)), 6259 0x2800); 6260 6261 bnx2x_cl45_write(bp, phy, 6262 5, 6263 (MDIO_REG_BANK_CL73_IEEEB0 + 6264 (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)), 6265 0x6041); 6266 msleep(200); 6267 /* Set aer mmd back */ 6268 bnx2x_set_aer_mmd(params, phy); 6269 6270 if (!CHIP_IS_E3(bp)) { 6271 /* And md_devad */ 6272 REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 6273 md_devad); 6274 } 6275 } else { 6276 u16 mii_ctrl; 6277 DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n"); 6278 bnx2x_cl45_read(bp, phy, 5, 6279 (MDIO_REG_BANK_COMBO_IEEE0 + 6280 (MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)), 6281 &mii_ctrl); 6282 bnx2x_cl45_write(bp, phy, 5, 6283 (MDIO_REG_BANK_COMBO_IEEE0 + 6284 (MDIO_COMBO_IEEE0_MII_CONTROL & 0xf)), 6285 mii_ctrl | 6286 MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK); 6287 } 6288} 6289 6290int bnx2x_set_led(struct link_params *params, 6291 struct link_vars *vars, u8 mode, u32 speed) 6292{ 6293 u8 port = params->port; 6294 u16 hw_led_mode = params->hw_led_mode; 6295 int rc = 0; 6296 u8 phy_idx; 6297 u32 tmp; 6298 u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; 6299 struct bnx2x *bp = params->bp; 6300 DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode); 6301 DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n", 6302 speed, hw_led_mode); 6303 /* In case */ 6304 for (phy_idx = EXT_PHY1; phy_idx < MAX_PHYS; phy_idx++) { 6305 if (params->phy[phy_idx].set_link_led) { 6306 params->phy[phy_idx].set_link_led( 6307 ¶ms->phy[phy_idx], params, mode); 6308 } 6309 } 6310 6311 switch (mode) { 6312 case LED_MODE_FRONT_PANEL_OFF: 6313 case LED_MODE_OFF: 6314 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0); 6315 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 6316 SHARED_HW_CFG_LED_MAC1); 6317 6318 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); 6319 if (params->phy[EXT_PHY1].type == 6320 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) 6321 tmp &= ~(EMAC_LED_1000MB_OVERRIDE | 6322 EMAC_LED_100MB_OVERRIDE | 6323 EMAC_LED_10MB_OVERRIDE); 6324 else 6325 tmp |= EMAC_LED_OVERRIDE; 6326 6327 EMAC_WR(bp, EMAC_REG_EMAC_LED, tmp); 6328 break; 6329 6330 case LED_MODE_OPER: 6331 /* For all other phys, OPER mode is same as ON, so in case 6332 * link is down, do nothing 6333 */ 6334 if (!vars->link_up) 6335 break; 6336 case LED_MODE_ON: 6337 if (((params->phy[EXT_PHY1].type == 6338 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) || 6339 (params->phy[EXT_PHY1].type == 6340 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722)) && 6341 CHIP_IS_E2(bp) && params->num_phys == 2) { 6342 /* This is a work-around for E2+8727 Configurations */ 6343 if (mode == LED_MODE_ON || 6344 speed == SPEED_10000){ 6345 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); 6346 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1); 6347 6348 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); 6349 EMAC_WR(bp, EMAC_REG_EMAC_LED, 6350 (tmp | EMAC_LED_OVERRIDE)); 6351 /* Return here without enabling traffic 6352 * LED blink and setting rate in ON mode. 6353 * In oper mode, enabling LED blink 6354 * and setting rate is needed. 6355 */ 6356 if (mode == LED_MODE_ON) 6357 return rc; 6358 } 6359 } else if (SINGLE_MEDIA_DIRECT(params)) { 6360 /* This is a work-around for HW issue found when link 6361 * is up in CL73 6362 */ 6363 if ((!CHIP_IS_E3(bp)) || 6364 (CHIP_IS_E3(bp) && 6365 mode == LED_MODE_ON)) 6366 REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1); 6367 6368 if (CHIP_IS_E1x(bp) || 6369 CHIP_IS_E2(bp) || 6370 (mode == LED_MODE_ON)) 6371 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); 6372 else 6373 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 6374 hw_led_mode); 6375 } else if ((params->phy[EXT_PHY1].type == 6376 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) && 6377 (mode == LED_MODE_ON)) { 6378 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); 6379 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); 6380 EMAC_WR(bp, EMAC_REG_EMAC_LED, tmp | 6381 EMAC_LED_OVERRIDE | EMAC_LED_1000MB_OVERRIDE); 6382 /* Break here; otherwise, it'll disable the 6383 * intended override. 6384 */ 6385 break; 6386 } else { 6387 u32 nig_led_mode = ((params->hw_led_mode << 6388 SHARED_HW_CFG_LED_MODE_SHIFT) == 6389 SHARED_HW_CFG_LED_EXTPHY2) ? 6390 (SHARED_HW_CFG_LED_PHY1 >> 6391 SHARED_HW_CFG_LED_MODE_SHIFT) : hw_led_mode; 6392 REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 6393 nig_led_mode); 6394 } 6395 6396 REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0); 6397 /* Set blinking rate to ~15.9Hz */ 6398 if (CHIP_IS_E3(bp)) 6399 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4, 6400 LED_BLINK_RATE_VAL_E3); 6401 else 6402 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4, 6403 LED_BLINK_RATE_VAL_E1X_E2); 6404 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + 6405 port*4, 1); 6406 tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); 6407 EMAC_WR(bp, EMAC_REG_EMAC_LED, 6408 (tmp & (~EMAC_LED_OVERRIDE))); 6409 6410 if (CHIP_IS_E1(bp) && 6411 ((speed == SPEED_2500) || 6412 (speed == SPEED_1000) || 6413 (speed == SPEED_100) || 6414 (speed == SPEED_10))) { 6415 /* For speeds less than 10G LED scheme is different */ 6416 REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 6417 + port*4, 1); 6418 REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 + 6419 port*4, 0); 6420 REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 + 6421 port*4, 1); 6422 } 6423 break; 6424 6425 default: 6426 rc = -EINVAL; 6427 DP(NETIF_MSG_LINK, "bnx2x_set_led: Invalid led mode %d\n", 6428 mode); 6429 break; 6430 } 6431 return rc; 6432 6433} 6434 6435/* This function comes to reflect the actual link state read DIRECTLY from the 6436 * HW 6437 */ 6438int bnx2x_test_link(struct link_params *params, struct link_vars *vars, 6439 u8 is_serdes) 6440{ 6441 struct bnx2x *bp = params->bp; 6442 u16 gp_status = 0, phy_index = 0; 6443 u8 ext_phy_link_up = 0, serdes_phy_type; 6444 struct link_vars temp_vars; 6445 struct bnx2x_phy *int_phy = ¶ms->phy[INT_PHY]; 6446 6447 if (CHIP_IS_E3(bp)) { 6448 u16 link_up; 6449 if (params->req_line_speed[LINK_CONFIG_IDX(INT_PHY)] 6450 > SPEED_10000) { 6451 /* Check 20G link */ 6452 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD, 6453 1, &link_up); 6454 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD, 6455 1, &link_up); 6456 link_up &= (1<<2); 6457 } else { 6458 /* Check 10G link and below*/ 6459 u8 lane = bnx2x_get_warpcore_lane(int_phy, params); 6460 bnx2x_cl45_read(bp, int_phy, MDIO_WC_DEVAD, 6461 MDIO_WC_REG_GP2_STATUS_GP_2_1, 6462 &gp_status); 6463 gp_status = ((gp_status >> 8) & 0xf) | 6464 ((gp_status >> 12) & 0xf); 6465 link_up = gp_status & (1 << lane); 6466 } 6467 if (!link_up) 6468 return -ESRCH; 6469 } else { 6470 CL22_RD_OVER_CL45(bp, int_phy, 6471 MDIO_REG_BANK_GP_STATUS, 6472 MDIO_GP_STATUS_TOP_AN_STATUS1, 6473 &gp_status); 6474 /* Link is up only if both local phy and external phy are up */ 6475 if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS)) 6476 return -ESRCH; 6477 } 6478 /* In XGXS loopback mode, do not check external PHY */ 6479 if (params->loopback_mode == LOOPBACK_XGXS) 6480 return 0; 6481 6482 switch (params->num_phys) { 6483 case 1: 6484 /* No external PHY */ 6485 return 0; 6486 case 2: 6487 ext_phy_link_up = params->phy[EXT_PHY1].read_status( 6488 ¶ms->phy[EXT_PHY1], 6489 params, &temp_vars); 6490 break; 6491 case 3: /* Dual Media */ 6492 for (phy_index = EXT_PHY1; phy_index < params->num_phys; 6493 phy_index++) { 6494 serdes_phy_type = ((params->phy[phy_index].media_type == 6495 ETH_PHY_SFPP_10G_FIBER) || 6496 (params->phy[phy_index].media_type == 6497 ETH_PHY_SFP_1G_FIBER) || 6498 (params->phy[phy_index].media_type == 6499 ETH_PHY_XFP_FIBER) || 6500 (params->phy[phy_index].media_type == 6501 ETH_PHY_DA_TWINAX)); 6502 6503 if (is_serdes != serdes_phy_type) 6504 continue; 6505 if (params->phy[phy_index].read_status) { 6506 ext_phy_link_up |= 6507 params->phy[phy_index].read_status( 6508 ¶ms->phy[phy_index], 6509 params, &temp_vars); 6510 } 6511 } 6512 break; 6513 } 6514 if (ext_phy_link_up) 6515 return 0; 6516 return -ESRCH; 6517} 6518 6519static int bnx2x_link_initialize(struct link_params *params, 6520 struct link_vars *vars) 6521{ 6522 u8 phy_index, non_ext_phy; 6523 struct bnx2x *bp = params->bp; 6524 /* In case of external phy existence, the line speed would be the 6525 * line speed linked up by the external phy. In case it is direct 6526 * only, then the line_speed during initialization will be 6527 * equal to the req_line_speed 6528 */ 6529 vars->line_speed = params->phy[INT_PHY].req_line_speed; 6530 6531 /* Initialize the internal phy in case this is a direct board 6532 * (no external phys), or this board has external phy which requires 6533 * to first. 6534 */ 6535 if (!USES_WARPCORE(bp)) 6536 bnx2x_prepare_xgxs(¶ms->phy[INT_PHY], params, vars); 6537 /* init ext phy and enable link state int */ 6538 non_ext_phy = (SINGLE_MEDIA_DIRECT(params) || 6539 (params->loopback_mode == LOOPBACK_XGXS)); 6540 6541 if (non_ext_phy || 6542 (params->phy[EXT_PHY1].flags & FLAGS_INIT_XGXS_FIRST) || 6543 (params->loopback_mode == LOOPBACK_EXT_PHY)) { 6544 struct bnx2x_phy *phy = ¶ms->phy[INT_PHY]; 6545 if (vars->line_speed == SPEED_AUTO_NEG && 6546 (CHIP_IS_E1x(bp) || 6547 CHIP_IS_E2(bp))) 6548 bnx2x_set_parallel_detection(phy, params); 6549 if (params->phy[INT_PHY].config_init) 6550 params->phy[INT_PHY].config_init(phy, params, vars); 6551 } 6552 6553 /* Re-read this value in case it was changed inside config_init due to 6554 * limitations of optic module 6555 */ 6556 vars->line_speed = params->phy[INT_PHY].req_line_speed; 6557 6558 /* Init external phy*/ 6559 if (non_ext_phy) { 6560 if (params->phy[INT_PHY].supported & 6561 SUPPORTED_FIBRE) 6562 vars->link_status |= LINK_STATUS_SERDES_LINK; 6563 } else { 6564 for (phy_index = EXT_PHY1; phy_index < params->num_phys; 6565 phy_index++) { 6566 /* No need to initialize second phy in case of first 6567 * phy only selection. In case of second phy, we do 6568 * need to initialize the first phy, since they are 6569 * connected. 6570 */ 6571 if (params->phy[phy_index].supported & 6572 SUPPORTED_FIBRE) 6573 vars->link_status |= LINK_STATUS_SERDES_LINK; 6574 6575 if (phy_index == EXT_PHY2 && 6576 (bnx2x_phy_selection(params) == 6577 PORT_HW_CFG_PHY_SELECTION_FIRST_PHY)) { 6578 DP(NETIF_MSG_LINK, 6579 "Not initializing second phy\n"); 6580 continue; 6581 } 6582 params->phy[phy_index].config_init( 6583 ¶ms->phy[phy_index], 6584 params, vars); 6585 } 6586 } 6587 /* Reset the interrupt indication after phy was initialized */ 6588 bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + 6589 params->port*4, 6590 (NIG_STATUS_XGXS0_LINK10G | 6591 NIG_STATUS_XGXS0_LINK_STATUS | 6592 NIG_STATUS_SERDES0_LINK_STATUS | 6593 NIG_MASK_MI_INT)); 6594 return 0; 6595} 6596 6597static void bnx2x_int_link_reset(struct bnx2x_phy *phy, 6598 struct link_params *params) 6599{ 6600 /* Reset the SerDes/XGXS */ 6601 REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, 6602 (0x1ff << (params->port*16))); 6603} 6604 6605static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy, 6606 struct link_params *params) 6607{ 6608 struct bnx2x *bp = params->bp; 6609 u8 gpio_port; 6610 /* HW reset */ 6611 if (CHIP_IS_E2(bp)) 6612 gpio_port = BP_PATH(bp); 6613 else 6614 gpio_port = params->port; 6615 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, 6616 MISC_REGISTERS_GPIO_OUTPUT_LOW, 6617 gpio_port); 6618 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 6619 MISC_REGISTERS_GPIO_OUTPUT_LOW, 6620 gpio_port); 6621 DP(NETIF_MSG_LINK, "reset external PHY\n"); 6622} 6623 6624static int bnx2x_update_link_down(struct link_params *params, 6625 struct link_vars *vars) 6626{ 6627 struct bnx2x *bp = params->bp; 6628 u8 port = params->port; 6629 6630 DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port); 6631 bnx2x_set_led(params, vars, LED_MODE_OFF, 0); 6632 vars->phy_flags &= ~PHY_PHYSICAL_LINK_FLAG; 6633 /* Indicate no mac active */ 6634 vars->mac_type = MAC_TYPE_NONE; 6635 6636 /* Update shared memory */ 6637 vars->link_status &= ~LINK_UPDATE_MASK; 6638 vars->line_speed = 0; 6639 bnx2x_update_mng(params, vars->link_status); 6640 6641 /* Activate nig drain */ 6642 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); 6643 6644 /* Disable emac */ 6645 if (!CHIP_IS_E3(bp)) 6646 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); 6647 6648 usleep_range(10000, 20000); 6649 /* Reset BigMac/Xmac */ 6650 if (CHIP_IS_E1x(bp) || 6651 CHIP_IS_E2(bp)) 6652 bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 0); 6653 6654 if (CHIP_IS_E3(bp)) { 6655 /* Prevent LPI Generation by chip */ 6656 REG_WR(bp, MISC_REG_CPMU_LP_FW_ENABLE_P0 + (params->port << 2), 6657 0); 6658 REG_WR(bp, MISC_REG_CPMU_LP_MASK_ENT_P0 + (params->port << 2), 6659 0); 6660 vars->eee_status &= ~(SHMEM_EEE_LP_ADV_STATUS_MASK | 6661 SHMEM_EEE_ACTIVE_BIT); 6662 6663 bnx2x_update_mng_eee(params, vars->eee_status); 6664 bnx2x_set_xmac_rxtx(params, 0); 6665 bnx2x_set_umac_rxtx(params, 0); 6666 } 6667 6668 return 0; 6669} 6670 6671static int bnx2x_update_link_up(struct link_params *params, 6672 struct link_vars *vars, 6673 u8 link_10g) 6674{ 6675 struct bnx2x *bp = params->bp; 6676 u8 phy_idx, port = params->port; 6677 int rc = 0; 6678 6679 vars->link_status |= (LINK_STATUS_LINK_UP | 6680 LINK_STATUS_PHYSICAL_LINK_FLAG); 6681 vars->phy_flags |= PHY_PHYSICAL_LINK_FLAG; 6682 6683 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX) 6684 vars->link_status |= 6685 LINK_STATUS_TX_FLOW_CONTROL_ENABLED; 6686 6687 if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX) 6688 vars->link_status |= 6689 LINK_STATUS_RX_FLOW_CONTROL_ENABLED; 6690 if (USES_WARPCORE(bp)) { 6691 if (link_10g) { 6692 if (bnx2x_xmac_enable(params, vars, 0) == 6693 -ESRCH) { 6694 DP(NETIF_MSG_LINK, "Found errors on XMAC\n"); 6695 vars->link_up = 0; 6696 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG; 6697 vars->link_status &= ~LINK_STATUS_LINK_UP; 6698 } 6699 } else 6700 bnx2x_umac_enable(params, vars, 0); 6701 bnx2x_set_led(params, vars, 6702 LED_MODE_OPER, vars->line_speed); 6703 6704 if ((vars->eee_status & SHMEM_EEE_ACTIVE_BIT) && 6705 (vars->eee_status & SHMEM_EEE_LPI_REQUESTED_BIT)) { 6706 DP(NETIF_MSG_LINK, "Enabling LPI assertion\n"); 6707 REG_WR(bp, MISC_REG_CPMU_LP_FW_ENABLE_P0 + 6708 (params->port << 2), 1); 6709 REG_WR(bp, MISC_REG_CPMU_LP_DR_ENABLE, 1); 6710 REG_WR(bp, MISC_REG_CPMU_LP_MASK_ENT_P0 + 6711 (params->port << 2), 0xfc20); 6712 } 6713 } 6714 if ((CHIP_IS_E1x(bp) || 6715 CHIP_IS_E2(bp))) { 6716 if (link_10g) { 6717 if (bnx2x_bmac_enable(params, vars, 0, 1) == 6718 -ESRCH) { 6719 DP(NETIF_MSG_LINK, "Found errors on BMAC\n"); 6720 vars->link_up = 0; 6721 vars->phy_flags |= PHY_HALF_OPEN_CONN_FLAG; 6722 vars->link_status &= ~LINK_STATUS_LINK_UP; 6723 } 6724 6725 bnx2x_set_led(params, vars, 6726 LED_MODE_OPER, SPEED_10000); 6727 } else { 6728 rc = bnx2x_emac_program(params, vars); 6729 bnx2x_emac_enable(params, vars, 0); 6730 6731 /* AN complete? */ 6732 if ((vars->link_status & 6733 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) 6734 && (!(vars->phy_flags & PHY_SGMII_FLAG)) && 6735 SINGLE_MEDIA_DIRECT(params)) 6736 bnx2x_set_gmii_tx_driver(params); 6737 } 6738 } 6739 6740 /* PBF - link up */ 6741 if (CHIP_IS_E1x(bp)) 6742 rc |= bnx2x_pbf_update(params, vars->flow_ctrl, 6743 vars->line_speed); 6744 6745 /* Disable drain */ 6746 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); 6747 6748 /* Update shared memory */ 6749 bnx2x_update_mng(params, vars->link_status); 6750 bnx2x_update_mng_eee(params, vars->eee_status); 6751 /* Check remote fault */ 6752 for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) { 6753 if (params->phy[phy_idx].flags & FLAGS_TX_ERROR_CHECK) { 6754 bnx2x_check_half_open_conn(params, vars, 0); 6755 break; 6756 } 6757 } 6758 msleep(20); 6759 return rc; 6760} 6761 6762static void bnx2x_chng_link_count(struct link_params *params, bool clear) 6763{ 6764 struct bnx2x *bp = params->bp; 6765 u32 addr, val; 6766 6767 /* Verify the link_change_count is supported by the MFW */ 6768 if (!(SHMEM2_HAS(bp, link_change_count))) 6769 return; 6770 6771 addr = params->shmem2_base + 6772 offsetof(struct shmem2_region, link_change_count[params->port]); 6773 if (clear) 6774 val = 0; 6775 else 6776 val = REG_RD(bp, addr) + 1; 6777 REG_WR(bp, addr, val); 6778} 6779 6780/* The bnx2x_link_update function should be called upon link 6781 * interrupt. 6782 * Link is considered up as follows: 6783 * - DIRECT_SINGLE_MEDIA - Only XGXS link (internal link) needs 6784 * to be up 6785 * - SINGLE_MEDIA - The link between the 577xx and the external 6786 * phy (XGXS) need to up as well as the external link of the 6787 * phy (PHY_EXT1) 6788 * - DUAL_MEDIA - The link between the 577xx and the first 6789 * external phy needs to be up, and at least one of the 2 6790 * external phy link must be up. 6791 */ 6792int bnx2x_link_update(struct link_params *params, struct link_vars *vars) 6793{ 6794 struct bnx2x *bp = params->bp; 6795 struct link_vars phy_vars[MAX_PHYS]; 6796 u8 port = params->port; 6797 u8 link_10g_plus, phy_index; 6798 u32 prev_link_status = vars->link_status; 6799 u8 ext_phy_link_up = 0, cur_link_up; 6800 int rc = 0; 6801 u8 is_mi_int = 0; 6802 u16 ext_phy_line_speed = 0, prev_line_speed = vars->line_speed; 6803 u8 active_external_phy = INT_PHY; 6804 vars->phy_flags &= ~PHY_HALF_OPEN_CONN_FLAG; 6805 vars->link_status &= ~LINK_UPDATE_MASK; 6806 for (phy_index = INT_PHY; phy_index < params->num_phys; 6807 phy_index++) { 6808 phy_vars[phy_index].flow_ctrl = 0; 6809 phy_vars[phy_index].link_status = 0; 6810 phy_vars[phy_index].line_speed = 0; 6811 phy_vars[phy_index].duplex = DUPLEX_FULL; 6812 phy_vars[phy_index].phy_link_up = 0; 6813 phy_vars[phy_index].link_up = 0; 6814 phy_vars[phy_index].fault_detected = 0; 6815 /* different consideration, since vars holds inner state */ 6816 phy_vars[phy_index].eee_status = vars->eee_status; 6817 } 6818 6819 if (USES_WARPCORE(bp)) 6820 bnx2x_set_aer_mmd(params, ¶ms->phy[INT_PHY]); 6821 6822 DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n", 6823 port, (vars->phy_flags & PHY_XGXS_FLAG), 6824 REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4)); 6825 6826 is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + 6827 port*0x18) > 0); 6828 DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n", 6829 REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), 6830 is_mi_int, 6831 REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c)); 6832 6833 DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n", 6834 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), 6835 REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); 6836 6837 /* Disable emac */ 6838 if (!CHIP_IS_E3(bp)) 6839 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); 6840 6841 /* Step 1: 6842 * Check external link change only for external phys, and apply 6843 * priority selection between them in case the link on both phys 6844 * is up. Note that instead of the common vars, a temporary 6845 * vars argument is used since each phy may have different link/ 6846 * speed/duplex result 6847 */ 6848 for (phy_index = EXT_PHY1; phy_index < params->num_phys; 6849 phy_index++) { 6850 struct bnx2x_phy *phy = ¶ms->phy[phy_index]; 6851 if (!phy->read_status) 6852 continue; 6853 /* Read link status and params of this ext phy */ 6854 cur_link_up = phy->read_status(phy, params, 6855 &phy_vars[phy_index]); 6856 if (cur_link_up) { 6857 DP(NETIF_MSG_LINK, "phy in index %d link is up\n", 6858 phy_index); 6859 } else { 6860 DP(NETIF_MSG_LINK, "phy in index %d link is down\n", 6861 phy_index); 6862 continue; 6863 } 6864 6865 if (!ext_phy_link_up) { 6866 ext_phy_link_up = 1; 6867 active_external_phy = phy_index; 6868 } else { 6869 switch (bnx2x_phy_selection(params)) { 6870 case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT: 6871 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY: 6872 /* In this option, the first PHY makes sure to pass the 6873 * traffic through itself only. 6874 * Its not clear how to reset the link on the second phy 6875 */ 6876 active_external_phy = EXT_PHY1; 6877 break; 6878 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY: 6879 /* In this option, the first PHY makes sure to pass the 6880 * traffic through the second PHY. 6881 */ 6882 active_external_phy = EXT_PHY2; 6883 break; 6884 default: 6885 /* Link indication on both PHYs with the following cases 6886 * is invalid: 6887 * - FIRST_PHY means that second phy wasn't initialized, 6888 * hence its link is expected to be down 6889 * - SECOND_PHY means that first phy should not be able 6890 * to link up by itself (using configuration) 6891 * - DEFAULT should be overriden during initialiazation 6892 */ 6893 DP(NETIF_MSG_LINK, "Invalid link indication" 6894 "mpc=0x%x. DISABLING LINK !!!\n", 6895 params->multi_phy_config); 6896 ext_phy_link_up = 0; 6897 break; 6898 } 6899 } 6900 } 6901 prev_line_speed = vars->line_speed; 6902 /* Step 2: 6903 * Read the status of the internal phy. In case of 6904 * DIRECT_SINGLE_MEDIA board, this link is the external link, 6905 * otherwise this is the link between the 577xx and the first 6906 * external phy 6907 */ 6908 if (params->phy[INT_PHY].read_status) 6909 params->phy[INT_PHY].read_status( 6910 ¶ms->phy[INT_PHY], 6911 params, vars); 6912 /* The INT_PHY flow control reside in the vars. This include the 6913 * case where the speed or flow control are not set to AUTO. 6914 * Otherwise, the active external phy flow control result is set 6915 * to the vars. The ext_phy_line_speed is needed to check if the 6916 * speed is different between the internal phy and external phy. 6917 * This case may be result of intermediate link speed change. 6918 */ 6919 if (active_external_phy > INT_PHY) { 6920 vars->flow_ctrl = phy_vars[active_external_phy].flow_ctrl; 6921 /* Link speed is taken from the XGXS. AN and FC result from 6922 * the external phy. 6923 */ 6924 vars->link_status |= phy_vars[active_external_phy].link_status; 6925 6926 /* if active_external_phy is first PHY and link is up - disable 6927 * disable TX on second external PHY 6928 */ 6929 if (active_external_phy == EXT_PHY1) { 6930 if (params->phy[EXT_PHY2].phy_specific_func) { 6931 DP(NETIF_MSG_LINK, 6932 "Disabling TX on EXT_PHY2\n"); 6933 params->phy[EXT_PHY2].phy_specific_func( 6934 ¶ms->phy[EXT_PHY2], 6935 params, DISABLE_TX); 6936 } 6937 } 6938 6939 ext_phy_line_speed = phy_vars[active_external_phy].line_speed; 6940 vars->duplex = phy_vars[active_external_phy].duplex; 6941 if (params->phy[active_external_phy].supported & 6942 SUPPORTED_FIBRE) 6943 vars->link_status |= LINK_STATUS_SERDES_LINK; 6944 else 6945 vars->link_status &= ~LINK_STATUS_SERDES_LINK; 6946 6947 vars->eee_status = phy_vars[active_external_phy].eee_status; 6948 6949 DP(NETIF_MSG_LINK, "Active external phy selected: %x\n", 6950 active_external_phy); 6951 } 6952 6953 for (phy_index = EXT_PHY1; phy_index < params->num_phys; 6954 phy_index++) { 6955 if (params->phy[phy_index].flags & 6956 FLAGS_REARM_LATCH_SIGNAL) { 6957 bnx2x_rearm_latch_signal(bp, port, 6958 phy_index == 6959 active_external_phy); 6960 break; 6961 } 6962 } 6963 DP(NETIF_MSG_LINK, "vars->flow_ctrl = 0x%x, vars->link_status = 0x%x," 6964 " ext_phy_line_speed = %d\n", vars->flow_ctrl, 6965 vars->link_status, ext_phy_line_speed); 6966 /* Upon link speed change set the NIG into drain mode. Comes to 6967 * deals with possible FIFO glitch due to clk change when speed 6968 * is decreased without link down indicator 6969 */ 6970 6971 if (vars->phy_link_up) { 6972 if (!(SINGLE_MEDIA_DIRECT(params)) && ext_phy_link_up && 6973 (ext_phy_line_speed != vars->line_speed)) { 6974 DP(NETIF_MSG_LINK, "Internal link speed %d is" 6975 " different than the external" 6976 " link speed %d\n", vars->line_speed, 6977 ext_phy_line_speed); 6978 vars->phy_link_up = 0; 6979 } else if (prev_line_speed != vars->line_speed) { 6980 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 6981 0); 6982 usleep_range(1000, 2000); 6983 } 6984 } 6985 6986 /* Anything 10 and over uses the bmac */ 6987 link_10g_plus = (vars->line_speed >= SPEED_10000); 6988 6989 bnx2x_link_int_ack(params, vars, link_10g_plus); 6990 6991 /* In case external phy link is up, and internal link is down 6992 * (not initialized yet probably after link initialization, it 6993 * needs to be initialized. 6994 * Note that after link down-up as result of cable plug, the xgxs 6995 * link would probably become up again without the need 6996 * initialize it 6997 */ 6998 if (!(SINGLE_MEDIA_DIRECT(params))) { 6999 DP(NETIF_MSG_LINK, "ext_phy_link_up = %d, int_link_up = %d," 7000 " init_preceding = %d\n", ext_phy_link_up, 7001 vars->phy_link_up, 7002 params->phy[EXT_PHY1].flags & 7003 FLAGS_INIT_XGXS_FIRST); 7004 if (!(params->phy[EXT_PHY1].flags & 7005 FLAGS_INIT_XGXS_FIRST) 7006 && ext_phy_link_up && !vars->phy_link_up) { 7007 vars->line_speed = ext_phy_line_speed; 7008 if (vars->line_speed < SPEED_1000) 7009 vars->phy_flags |= PHY_SGMII_FLAG; 7010 else 7011 vars->phy_flags &= ~PHY_SGMII_FLAG; 7012 7013 if (params->phy[INT_PHY].config_init) 7014 params->phy[INT_PHY].config_init( 7015 ¶ms->phy[INT_PHY], params, 7016 vars); 7017 } 7018 } 7019 /* Link is up only if both local phy and external phy (in case of 7020 * non-direct board) are up and no fault detected on active PHY. 7021 */ 7022 vars->link_up = (vars->phy_link_up && 7023 (ext_phy_link_up || 7024 SINGLE_MEDIA_DIRECT(params)) && 7025 (phy_vars[active_external_phy].fault_detected == 0)); 7026 7027 /* Update the PFC configuration in case it was changed */ 7028 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) 7029 vars->link_status |= LINK_STATUS_PFC_ENABLED; 7030 else 7031 vars->link_status &= ~LINK_STATUS_PFC_ENABLED; 7032 7033 if (vars->link_up) 7034 rc = bnx2x_update_link_up(params, vars, link_10g_plus); 7035 else 7036 rc = bnx2x_update_link_down(params, vars); 7037 7038 if ((prev_link_status ^ vars->link_status) & LINK_STATUS_LINK_UP) 7039 bnx2x_chng_link_count(params, false); 7040 7041 /* Update MCP link status was changed */ 7042 if (params->feature_config_flags & FEATURE_CONFIG_BC_SUPPORTS_AFEX) 7043 bnx2x_fw_command(bp, DRV_MSG_CODE_LINK_STATUS_CHANGED, 0); 7044 7045 return rc; 7046} 7047 7048/*****************************************************************************/ 7049/* External Phy section */ 7050/*****************************************************************************/ 7051void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port) 7052{ 7053 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, 7054 MISC_REGISTERS_GPIO_OUTPUT_LOW, port); 7055 usleep_range(1000, 2000); 7056 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, 7057 MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); 7058} 7059 7060static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port, 7061 u32 spirom_ver, u32 ver_addr) 7062{ 7063 DP(NETIF_MSG_LINK, "FW version 0x%x:0x%x for port %d\n", 7064 (u16)(spirom_ver>>16), (u16)spirom_ver, port); 7065 7066 if (ver_addr) 7067 REG_WR(bp, ver_addr, spirom_ver); 7068} 7069 7070static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp, 7071 struct bnx2x_phy *phy, 7072 u8 port) 7073{ 7074 u16 fw_ver1, fw_ver2; 7075 7076 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 7077 MDIO_PMA_REG_ROM_VER1, &fw_ver1); 7078 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 7079 MDIO_PMA_REG_ROM_VER2, &fw_ver2); 7080 bnx2x_save_spirom_version(bp, port, (u32)(fw_ver1<<16 | fw_ver2), 7081 phy->ver_addr); 7082} 7083 7084static void bnx2x_ext_phy_10G_an_resolve(struct bnx2x *bp, 7085 struct bnx2x_phy *phy, 7086 struct link_vars *vars) 7087{ 7088 u16 val; 7089 bnx2x_cl45_read(bp, phy, 7090 MDIO_AN_DEVAD, 7091 MDIO_AN_REG_STATUS, &val); 7092 bnx2x_cl45_read(bp, phy, 7093 MDIO_AN_DEVAD, 7094 MDIO_AN_REG_STATUS, &val); 7095 if (val & (1<<5)) 7096 vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; 7097 if ((val & (1<<0)) == 0) 7098 vars->link_status |= LINK_STATUS_PARALLEL_DETECTION_USED; 7099} 7100 7101/******************************************************************/ 7102/* common BCM8073/BCM8727 PHY SECTION */ 7103/******************************************************************/ 7104static void bnx2x_8073_resolve_fc(struct bnx2x_phy *phy, 7105 struct link_params *params, 7106 struct link_vars *vars) 7107{ 7108 struct bnx2x *bp = params->bp; 7109 if (phy->req_line_speed == SPEED_10 || 7110 phy->req_line_speed == SPEED_100) { 7111 vars->flow_ctrl = phy->req_flow_ctrl; 7112 return; 7113 } 7114 7115 if (bnx2x_ext_phy_resolve_fc(phy, params, vars) && 7116 (vars->flow_ctrl == BNX2X_FLOW_CTRL_NONE)) { 7117 u16 pause_result; 7118 u16 ld_pause; /* local */ 7119 u16 lp_pause; /* link partner */ 7120 bnx2x_cl45_read(bp, phy, 7121 MDIO_AN_DEVAD, 7122 MDIO_AN_REG_CL37_FC_LD, &ld_pause); 7123 7124 bnx2x_cl45_read(bp, phy, 7125 MDIO_AN_DEVAD, 7126 MDIO_AN_REG_CL37_FC_LP, &lp_pause); 7127 pause_result = (ld_pause & 7128 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5; 7129 pause_result |= (lp_pause & 7130 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7; 7131 7132 bnx2x_pause_resolve(vars, pause_result); 7133 DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x\n", 7134 pause_result); 7135 } 7136} 7137static int bnx2x_8073_8727_external_rom_boot(struct bnx2x *bp, 7138 struct bnx2x_phy *phy, 7139 u8 port) 7140{ 7141 u32 count = 0; 7142 u16 fw_ver1, fw_msgout; 7143 int rc = 0; 7144 7145 /* Boot port from external ROM */ 7146 /* EDC grst */ 7147 bnx2x_cl45_write(bp, phy, 7148 MDIO_PMA_DEVAD, 7149 MDIO_PMA_REG_GEN_CTRL, 7150 0x0001); 7151 7152 /* Ucode reboot and rst */ 7153 bnx2x_cl45_write(bp, phy, 7154 MDIO_PMA_DEVAD, 7155 MDIO_PMA_REG_GEN_CTRL, 7156 0x008c); 7157 7158 bnx2x_cl45_write(bp, phy, 7159 MDIO_PMA_DEVAD, 7160 MDIO_PMA_REG_MISC_CTRL1, 0x0001); 7161 7162 /* Reset internal microprocessor */ 7163 bnx2x_cl45_write(bp, phy, 7164 MDIO_PMA_DEVAD, 7165 MDIO_PMA_REG_GEN_CTRL, 7166 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); 7167 7168 /* Release srst bit */ 7169 bnx2x_cl45_write(bp, phy, 7170 MDIO_PMA_DEVAD, 7171 MDIO_PMA_REG_GEN_CTRL, 7172 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); 7173 7174 /* Delay 100ms per the PHY specifications */ 7175 msleep(100); 7176 7177 /* 8073 sometimes taking longer to download */ 7178 do { 7179 count++; 7180 if (count > 300) { 7181 DP(NETIF_MSG_LINK, 7182 "bnx2x_8073_8727_external_rom_boot port %x:" 7183 "Download failed. fw version = 0x%x\n", 7184 port, fw_ver1); 7185 rc = -EINVAL; 7186 break; 7187 } 7188 7189 bnx2x_cl45_read(bp, phy, 7190 MDIO_PMA_DEVAD, 7191 MDIO_PMA_REG_ROM_VER1, &fw_ver1); 7192 bnx2x_cl45_read(bp, phy, 7193 MDIO_PMA_DEVAD, 7194 MDIO_PMA_REG_M8051_MSGOUT_REG, &fw_msgout); 7195 7196 usleep_range(1000, 2000); 7197 } while (fw_ver1 == 0 || fw_ver1 == 0x4321 || 7198 ((fw_msgout & 0xff) != 0x03 && (phy->type == 7199 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073))); 7200 7201 /* Clear ser_boot_ctl bit */ 7202 bnx2x_cl45_write(bp, phy, 7203 MDIO_PMA_DEVAD, 7204 MDIO_PMA_REG_MISC_CTRL1, 0x0000); 7205 bnx2x_save_bcm_spirom_ver(bp, phy, port); 7206 7207 DP(NETIF_MSG_LINK, 7208 "bnx2x_8073_8727_external_rom_boot port %x:" 7209 "Download complete. fw version = 0x%x\n", 7210 port, fw_ver1); 7211 7212 return rc; 7213} 7214 7215/******************************************************************/ 7216/* BCM8073 PHY SECTION */ 7217/******************************************************************/ 7218static int bnx2x_8073_is_snr_needed(struct bnx2x *bp, struct bnx2x_phy *phy) 7219{ 7220 /* This is only required for 8073A1, version 102 only */ 7221 u16 val; 7222 7223 /* Read 8073 HW revision*/ 7224 bnx2x_cl45_read(bp, phy, 7225 MDIO_PMA_DEVAD, 7226 MDIO_PMA_REG_8073_CHIP_REV, &val); 7227 7228 if (val != 1) { 7229 /* No need to workaround in 8073 A1 */ 7230 return 0; 7231 } 7232 7233 bnx2x_cl45_read(bp, phy, 7234 MDIO_PMA_DEVAD, 7235 MDIO_PMA_REG_ROM_VER2, &val); 7236 7237 /* SNR should be applied only for version 0x102 */ 7238 if (val != 0x102) 7239 return 0; 7240 7241 return 1; 7242} 7243 7244static int bnx2x_8073_xaui_wa(struct bnx2x *bp, struct bnx2x_phy *phy) 7245{ 7246 u16 val, cnt, cnt1 ; 7247 7248 bnx2x_cl45_read(bp, phy, 7249 MDIO_PMA_DEVAD, 7250 MDIO_PMA_REG_8073_CHIP_REV, &val); 7251 7252 if (val > 0) { 7253 /* No need to workaround in 8073 A1 */ 7254 return 0; 7255 } 7256 /* XAUI workaround in 8073 A0: */ 7257 7258 /* After loading the boot ROM and restarting Autoneg, poll 7259 * Dev1, Reg $C820: 7260 */ 7261 7262 for (cnt = 0; cnt < 1000; cnt++) { 7263 bnx2x_cl45_read(bp, phy, 7264 MDIO_PMA_DEVAD, 7265 MDIO_PMA_REG_8073_SPEED_LINK_STATUS, 7266 &val); 7267 /* If bit [14] = 0 or bit [13] = 0, continue on with 7268 * system initialization (XAUI work-around not required, as 7269 * these bits indicate 2.5G or 1G link up). 7270 */ 7271 if (!(val & (1<<14)) || !(val & (1<<13))) { 7272 DP(NETIF_MSG_LINK, "XAUI work-around not required\n"); 7273 return 0; 7274 } else if (!(val & (1<<15))) { 7275 DP(NETIF_MSG_LINK, "bit 15 went off\n"); 7276 /* If bit 15 is 0, then poll Dev1, Reg $C841 until it's 7277 * MSB (bit15) goes to 1 (indicating that the XAUI 7278 * workaround has completed), then continue on with 7279 * system initialization. 7280 */ 7281 for (cnt1 = 0; cnt1 < 1000; cnt1++) { 7282 bnx2x_cl45_read(bp, phy, 7283 MDIO_PMA_DEVAD, 7284 MDIO_PMA_REG_8073_XAUI_WA, &val); 7285 if (val & (1<<15)) { 7286 DP(NETIF_MSG_LINK, 7287 "XAUI workaround has completed\n"); 7288 return 0; 7289 } 7290 usleep_range(3000, 6000); 7291 } 7292 break; 7293 } 7294 usleep_range(3000, 6000); 7295 } 7296 DP(NETIF_MSG_LINK, "Warning: XAUI work-around timeout !!!\n"); 7297 return -EINVAL; 7298} 7299 7300static void bnx2x_807x_force_10G(struct bnx2x *bp, struct bnx2x_phy *phy) 7301{ 7302 /* Force KR or KX */ 7303 bnx2x_cl45_write(bp, phy, 7304 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040); 7305 bnx2x_cl45_write(bp, phy, 7306 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0x000b); 7307 bnx2x_cl45_write(bp, phy, 7308 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0000); 7309 bnx2x_cl45_write(bp, phy, 7310 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000); 7311} 7312 7313static void bnx2x_8073_set_pause_cl37(struct link_params *params, 7314 struct bnx2x_phy *phy, 7315 struct link_vars *vars) 7316{ 7317 u16 cl37_val; 7318 struct bnx2x *bp = params->bp; 7319 bnx2x_cl45_read(bp, phy, 7320 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &cl37_val); 7321 7322 cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; 7323 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ 7324 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc); 7325 if ((vars->ieee_fc & 7326 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) == 7327 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) { 7328 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC; 7329 } 7330 if ((vars->ieee_fc & 7331 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == 7332 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { 7333 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; 7334 } 7335 if ((vars->ieee_fc & 7336 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == 7337 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { 7338 cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; 7339 } 7340 DP(NETIF_MSG_LINK, 7341 "Ext phy AN advertize cl37 0x%x\n", cl37_val); 7342 7343 bnx2x_cl45_write(bp, phy, 7344 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, cl37_val); 7345 msleep(500); 7346} 7347 7348static void bnx2x_8073_specific_func(struct bnx2x_phy *phy, 7349 struct link_params *params, 7350 u32 action) 7351{ 7352 struct bnx2x *bp = params->bp; 7353 switch (action) { 7354 case PHY_INIT: 7355 /* Enable LASI */ 7356 bnx2x_cl45_write(bp, phy, 7357 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, (1<<2)); 7358 bnx2x_cl45_write(bp, phy, 7359 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x0004); 7360 break; 7361 } 7362} 7363 7364static int bnx2x_8073_config_init(struct bnx2x_phy *phy, 7365 struct link_params *params, 7366 struct link_vars *vars) 7367{ 7368 struct bnx2x *bp = params->bp; 7369 u16 val = 0, tmp1; 7370 u8 gpio_port; 7371 DP(NETIF_MSG_LINK, "Init 8073\n"); 7372 7373 if (CHIP_IS_E2(bp)) 7374 gpio_port = BP_PATH(bp); 7375 else 7376 gpio_port = params->port; 7377 /* Restore normal power mode*/ 7378 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 7379 MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); 7380 7381 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, 7382 MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); 7383 7384 bnx2x_8073_specific_func(phy, params, PHY_INIT); 7385 bnx2x_8073_set_pause_cl37(params, phy, vars); 7386 7387 bnx2x_cl45_read(bp, phy, 7388 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1); 7389 7390 bnx2x_cl45_read(bp, phy, 7391 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1); 7392 7393 DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1): 0x%x\n", tmp1); 7394 7395 /* Swap polarity if required - Must be done only in non-1G mode */ 7396 if (params->lane_config & PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) { 7397 /* Configure the 8073 to swap _P and _N of the KR lines */ 7398 DP(NETIF_MSG_LINK, "Swapping polarity for the 8073\n"); 7399 /* 10G Rx/Tx and 1G Tx signal polarity swap */ 7400 bnx2x_cl45_read(bp, phy, 7401 MDIO_PMA_DEVAD, 7402 MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, &val); 7403 bnx2x_cl45_write(bp, phy, 7404 MDIO_PMA_DEVAD, 7405 MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL, 7406 (val | (3<<9))); 7407 } 7408 7409 7410 /* Enable CL37 BAM */ 7411 if (REG_RD(bp, params->shmem_base + 7412 offsetof(struct shmem_region, dev_info. 7413 port_hw_config[params->port].default_cfg)) & 7414 PORT_HW_CFG_ENABLE_BAM_ON_KR_ENABLED) { 7415 7416 bnx2x_cl45_read(bp, phy, 7417 MDIO_AN_DEVAD, 7418 MDIO_AN_REG_8073_BAM, &val); 7419 bnx2x_cl45_write(bp, phy, 7420 MDIO_AN_DEVAD, 7421 MDIO_AN_REG_8073_BAM, val | 1); 7422 DP(NETIF_MSG_LINK, "Enable CL37 BAM on KR\n"); 7423 } 7424 if (params->loopback_mode == LOOPBACK_EXT) { 7425 bnx2x_807x_force_10G(bp, phy); 7426 DP(NETIF_MSG_LINK, "Forced speed 10G on 807X\n"); 7427 return 0; 7428 } else { 7429 bnx2x_cl45_write(bp, phy, 7430 MDIO_PMA_DEVAD, MDIO_PMA_REG_BCM_CTRL, 0x0002); 7431 } 7432 if (phy->req_line_speed != SPEED_AUTO_NEG) { 7433 if (phy->req_line_speed == SPEED_10000) { 7434 val = (1<<7); 7435 } else if (phy->req_line_speed == SPEED_2500) { 7436 val = (1<<5); 7437 /* Note that 2.5G works only when used with 1G 7438 * advertisement 7439 */ 7440 } else 7441 val = (1<<5); 7442 } else { 7443 val = 0; 7444 if (phy->speed_cap_mask & 7445 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) 7446 val |= (1<<7); 7447 7448 /* Note that 2.5G works only when used with 1G advertisement */ 7449 if (phy->speed_cap_mask & 7450 (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G | 7451 PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) 7452 val |= (1<<5); 7453 DP(NETIF_MSG_LINK, "807x autoneg val = 0x%x\n", val); 7454 } 7455 7456 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV, val); 7457 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, &tmp1); 7458 7459 if (((phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) && 7460 (phy->req_line_speed == SPEED_AUTO_NEG)) || 7461 (phy->req_line_speed == SPEED_2500)) { 7462 u16 phy_ver; 7463 /* Allow 2.5G for A1 and above */ 7464 bnx2x_cl45_read(bp, phy, 7465 MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_CHIP_REV, 7466 &phy_ver); 7467 DP(NETIF_MSG_LINK, "Add 2.5G\n"); 7468 if (phy_ver > 0) 7469 tmp1 |= 1; 7470 else 7471 tmp1 &= 0xfffe; 7472 } else { 7473 DP(NETIF_MSG_LINK, "Disable 2.5G\n"); 7474 tmp1 &= 0xfffe; 7475 } 7476 7477 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_8073_2_5G, tmp1); 7478 /* Add support for CL37 (passive mode) II */ 7479 7480 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, &tmp1); 7481 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, 7482 (tmp1 | ((phy->req_duplex == DUPLEX_FULL) ? 7483 0x20 : 0x40))); 7484 7485 /* Add support for CL37 (passive mode) III */ 7486 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); 7487 7488 /* The SNR will improve about 2db by changing BW and FEE main 7489 * tap. Rest commands are executed after link is up 7490 * Change FFE main cursor to 5 in EDC register 7491 */ 7492 if (bnx2x_8073_is_snr_needed(bp, phy)) 7493 bnx2x_cl45_write(bp, phy, 7494 MDIO_PMA_DEVAD, MDIO_PMA_REG_EDC_FFE_MAIN, 7495 0xFB0C); 7496 7497 /* Enable FEC (Forware Error Correction) Request in the AN */ 7498 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, &tmp1); 7499 tmp1 |= (1<<15); 7500 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_ADV2, tmp1); 7501 7502 bnx2x_ext_phy_set_pause(params, phy, vars); 7503 7504 /* Restart autoneg */ 7505 msleep(500); 7506 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200); 7507 DP(NETIF_MSG_LINK, "807x Autoneg Restart: Advertise 1G=%x, 10G=%x\n", 7508 ((val & (1<<5)) > 0), ((val & (1<<7)) > 0)); 7509 return 0; 7510} 7511 7512static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy, 7513 struct link_params *params, 7514 struct link_vars *vars) 7515{ 7516 struct bnx2x *bp = params->bp; 7517 u8 link_up = 0; 7518 u16 val1, val2; 7519 u16 link_status = 0; 7520 u16 an1000_status = 0; 7521 7522 bnx2x_cl45_read(bp, phy, 7523 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1); 7524 7525 DP(NETIF_MSG_LINK, "8703 LASI status 0x%x\n", val1); 7526 7527 /* Clear the interrupt LASI status register */ 7528 bnx2x_cl45_read(bp, phy, 7529 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2); 7530 bnx2x_cl45_read(bp, phy, 7531 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val1); 7532 DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", val2, val1); 7533 /* Clear MSG-OUT */ 7534 bnx2x_cl45_read(bp, phy, 7535 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1); 7536 7537 /* Check the LASI */ 7538 bnx2x_cl45_read(bp, phy, 7539 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &val2); 7540 7541 DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2); 7542 7543 /* Check the link status */ 7544 bnx2x_cl45_read(bp, phy, 7545 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &val2); 7546 DP(NETIF_MSG_LINK, "KR PCS status 0x%x\n", val2); 7547 7548 bnx2x_cl45_read(bp, phy, 7549 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2); 7550 bnx2x_cl45_read(bp, phy, 7551 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1); 7552 link_up = ((val1 & 4) == 4); 7553 DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1); 7554 7555 if (link_up && 7556 ((phy->req_line_speed != SPEED_10000))) { 7557 if (bnx2x_8073_xaui_wa(bp, phy) != 0) 7558 return 0; 7559 } 7560 bnx2x_cl45_read(bp, phy, 7561 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status); 7562 bnx2x_cl45_read(bp, phy, 7563 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &an1000_status); 7564 7565 /* Check the link status on 1.1.2 */ 7566 bnx2x_cl45_read(bp, phy, 7567 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2); 7568 bnx2x_cl45_read(bp, phy, 7569 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1); 7570 DP(NETIF_MSG_LINK, "KR PMA status 0x%x->0x%x," 7571 "an_link_status=0x%x\n", val2, val1, an1000_status); 7572 7573 link_up = (((val1 & 4) == 4) || (an1000_status & (1<<1))); 7574 if (link_up && bnx2x_8073_is_snr_needed(bp, phy)) { 7575 /* The SNR will improve about 2dbby changing the BW and FEE main 7576 * tap. The 1st write to change FFE main tap is set before 7577 * restart AN. Change PLL Bandwidth in EDC register 7578 */ 7579 bnx2x_cl45_write(bp, phy, 7580 MDIO_PMA_DEVAD, MDIO_PMA_REG_PLL_BANDWIDTH, 7581 0x26BC); 7582 7583 /* Change CDR Bandwidth in EDC register */ 7584 bnx2x_cl45_write(bp, phy, 7585 MDIO_PMA_DEVAD, MDIO_PMA_REG_CDR_BANDWIDTH, 7586 0x0333); 7587 } 7588 bnx2x_cl45_read(bp, phy, 7589 MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_SPEED_LINK_STATUS, 7590 &link_status); 7591 7592 /* Bits 0..2 --> speed detected, bits 13..15--> link is down */ 7593 if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) { 7594 link_up = 1; 7595 vars->line_speed = SPEED_10000; 7596 DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n", 7597 params->port); 7598 } else if ((link_status & (1<<1)) && (!(link_status & (1<<14)))) { 7599 link_up = 1; 7600 vars->line_speed = SPEED_2500; 7601 DP(NETIF_MSG_LINK, "port %x: External link up in 2.5G\n", 7602 params->port); 7603 } else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) { 7604 link_up = 1; 7605 vars->line_speed = SPEED_1000; 7606 DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n", 7607 params->port); 7608 } else { 7609 link_up = 0; 7610 DP(NETIF_MSG_LINK, "port %x: External link is down\n", 7611 params->port); 7612 } 7613 7614 if (link_up) { 7615 /* Swap polarity if required */ 7616 if (params->lane_config & 7617 PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) { 7618 /* Configure the 8073 to swap P and N of the KR lines */ 7619 bnx2x_cl45_read(bp, phy, 7620 MDIO_XS_DEVAD, 7621 MDIO_XS_REG_8073_RX_CTRL_PCIE, &val1); 7622 /* Set bit 3 to invert Rx in 1G mode and clear this bit 7623 * when it`s in 10G mode. 7624 */ 7625 if (vars->line_speed == SPEED_1000) { 7626 DP(NETIF_MSG_LINK, "Swapping 1G polarity for" 7627 "the 8073\n"); 7628 val1 |= (1<<3); 7629 } else 7630 val1 &= ~(1<<3); 7631 7632 bnx2x_cl45_write(bp, phy, 7633 MDIO_XS_DEVAD, 7634 MDIO_XS_REG_8073_RX_CTRL_PCIE, 7635 val1); 7636 } 7637 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars); 7638 bnx2x_8073_resolve_fc(phy, params, vars); 7639 vars->duplex = DUPLEX_FULL; 7640 } 7641 7642 if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) { 7643 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 7644 MDIO_AN_REG_LP_AUTO_NEG2, &val1); 7645 7646 if (val1 & (1<<5)) 7647 vars->link_status |= 7648 LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE; 7649 if (val1 & (1<<7)) 7650 vars->link_status |= 7651 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 7652 } 7653 7654 return link_up; 7655} 7656 7657static void bnx2x_8073_link_reset(struct bnx2x_phy *phy, 7658 struct link_params *params) 7659{ 7660 struct bnx2x *bp = params->bp; 7661 u8 gpio_port; 7662 if (CHIP_IS_E2(bp)) 7663 gpio_port = BP_PATH(bp); 7664 else 7665 gpio_port = params->port; 7666 DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n", 7667 gpio_port); 7668 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 7669 MISC_REGISTERS_GPIO_OUTPUT_LOW, 7670 gpio_port); 7671} 7672 7673/******************************************************************/ 7674/* BCM8705 PHY SECTION */ 7675/******************************************************************/ 7676static int bnx2x_8705_config_init(struct bnx2x_phy *phy, 7677 struct link_params *params, 7678 struct link_vars *vars) 7679{ 7680 struct bnx2x *bp = params->bp; 7681 DP(NETIF_MSG_LINK, "init 8705\n"); 7682 /* Restore normal power mode*/ 7683 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 7684 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); 7685 /* HW reset */ 7686 bnx2x_ext_phy_hw_reset(bp, params->port); 7687 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040); 7688 bnx2x_wait_reset_complete(bp, phy, params); 7689 7690 bnx2x_cl45_write(bp, phy, 7691 MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL, 0x8288); 7692 bnx2x_cl45_write(bp, phy, 7693 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 0x7fbf); 7694 bnx2x_cl45_write(bp, phy, 7695 MDIO_PMA_DEVAD, MDIO_PMA_REG_CMU_PLL_BYPASS, 0x0100); 7696 bnx2x_cl45_write(bp, phy, 7697 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_CNTL, 0x1); 7698 /* BCM8705 doesn't have microcode, hence the 0 */ 7699 bnx2x_save_spirom_version(bp, params->port, params->shmem_base, 0); 7700 return 0; 7701} 7702 7703static u8 bnx2x_8705_read_status(struct bnx2x_phy *phy, 7704 struct link_params *params, 7705 struct link_vars *vars) 7706{ 7707 u8 link_up = 0; 7708 u16 val1, rx_sd; 7709 struct bnx2x *bp = params->bp; 7710 DP(NETIF_MSG_LINK, "read status 8705\n"); 7711 bnx2x_cl45_read(bp, phy, 7712 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1); 7713 DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1); 7714 7715 bnx2x_cl45_read(bp, phy, 7716 MDIO_WIS_DEVAD, MDIO_WIS_REG_LASI_STATUS, &val1); 7717 DP(NETIF_MSG_LINK, "8705 LASI status 0x%x\n", val1); 7718 7719 bnx2x_cl45_read(bp, phy, 7720 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd); 7721 7722 bnx2x_cl45_read(bp, phy, 7723 MDIO_PMA_DEVAD, 0xc809, &val1); 7724 bnx2x_cl45_read(bp, phy, 7725 MDIO_PMA_DEVAD, 0xc809, &val1); 7726 7727 DP(NETIF_MSG_LINK, "8705 1.c809 val=0x%x\n", val1); 7728 link_up = ((rx_sd & 0x1) && (val1 & (1<<9)) && ((val1 & (1<<8)) == 0)); 7729 if (link_up) { 7730 vars->line_speed = SPEED_10000; 7731 bnx2x_ext_phy_resolve_fc(phy, params, vars); 7732 } 7733 return link_up; 7734} 7735 7736/******************************************************************/ 7737/* SFP+ module Section */ 7738/******************************************************************/ 7739static void bnx2x_set_disable_pmd_transmit(struct link_params *params, 7740 struct bnx2x_phy *phy, 7741 u8 pmd_dis) 7742{ 7743 struct bnx2x *bp = params->bp; 7744 /* Disable transmitter only for bootcodes which can enable it afterwards 7745 * (for D3 link) 7746 */ 7747 if (pmd_dis) { 7748 if (params->feature_config_flags & 7749 FEATURE_CONFIG_BC_SUPPORTS_SFP_TX_DISABLED) 7750 DP(NETIF_MSG_LINK, "Disabling PMD transmitter\n"); 7751 else { 7752 DP(NETIF_MSG_LINK, "NOT disabling PMD transmitter\n"); 7753 return; 7754 } 7755 } else 7756 DP(NETIF_MSG_LINK, "Enabling PMD transmitter\n"); 7757 bnx2x_cl45_write(bp, phy, 7758 MDIO_PMA_DEVAD, 7759 MDIO_PMA_REG_TX_DISABLE, pmd_dis); 7760} 7761 7762static u8 bnx2x_get_gpio_port(struct link_params *params) 7763{ 7764 u8 gpio_port; 7765 u32 swap_val, swap_override; 7766 struct bnx2x *bp = params->bp; 7767 if (CHIP_IS_E2(bp)) 7768 gpio_port = BP_PATH(bp); 7769 else 7770 gpio_port = params->port; 7771 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); 7772 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); 7773 return gpio_port ^ (swap_val && swap_override); 7774} 7775 7776static void bnx2x_sfp_e1e2_set_transmitter(struct link_params *params, 7777 struct bnx2x_phy *phy, 7778 u8 tx_en) 7779{ 7780 u16 val; 7781 u8 port = params->port; 7782 struct bnx2x *bp = params->bp; 7783 u32 tx_en_mode; 7784 7785 /* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/ 7786 tx_en_mode = REG_RD(bp, params->shmem_base + 7787 offsetof(struct shmem_region, 7788 dev_info.port_hw_config[port].sfp_ctrl)) & 7789 PORT_HW_CFG_TX_LASER_MASK; 7790 DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x " 7791 "mode = %x\n", tx_en, port, tx_en_mode); 7792 switch (tx_en_mode) { 7793 case PORT_HW_CFG_TX_LASER_MDIO: 7794 7795 bnx2x_cl45_read(bp, phy, 7796 MDIO_PMA_DEVAD, 7797 MDIO_PMA_REG_PHY_IDENTIFIER, 7798 &val); 7799 7800 if (tx_en) 7801 val &= ~(1<<15); 7802 else 7803 val |= (1<<15); 7804 7805 bnx2x_cl45_write(bp, phy, 7806 MDIO_PMA_DEVAD, 7807 MDIO_PMA_REG_PHY_IDENTIFIER, 7808 val); 7809 break; 7810 case PORT_HW_CFG_TX_LASER_GPIO0: 7811 case PORT_HW_CFG_TX_LASER_GPIO1: 7812 case PORT_HW_CFG_TX_LASER_GPIO2: 7813 case PORT_HW_CFG_TX_LASER_GPIO3: 7814 { 7815 u16 gpio_pin; 7816 u8 gpio_port, gpio_mode; 7817 if (tx_en) 7818 gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_HIGH; 7819 else 7820 gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_LOW; 7821 7822 gpio_pin = tx_en_mode - PORT_HW_CFG_TX_LASER_GPIO0; 7823 gpio_port = bnx2x_get_gpio_port(params); 7824 bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port); 7825 break; 7826 } 7827 default: 7828 DP(NETIF_MSG_LINK, "Invalid TX_LASER_MDIO 0x%x\n", tx_en_mode); 7829 break; 7830 } 7831} 7832 7833static void bnx2x_sfp_set_transmitter(struct link_params *params, 7834 struct bnx2x_phy *phy, 7835 u8 tx_en) 7836{ 7837 struct bnx2x *bp = params->bp; 7838 DP(NETIF_MSG_LINK, "Setting SFP+ transmitter to %d\n", tx_en); 7839 if (CHIP_IS_E3(bp)) 7840 bnx2x_sfp_e3_set_transmitter(params, phy, tx_en); 7841 else 7842 bnx2x_sfp_e1e2_set_transmitter(params, phy, tx_en); 7843} 7844 7845static int bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy, 7846 struct link_params *params, 7847 u8 dev_addr, u16 addr, u8 byte_cnt, 7848 u8 *o_buf, u8 is_init) 7849{ 7850 struct bnx2x *bp = params->bp; 7851 u16 val = 0; 7852 u16 i; 7853 if (byte_cnt > SFP_EEPROM_PAGE_SIZE) { 7854 DP(NETIF_MSG_LINK, 7855 "Reading from eeprom is limited to 0xf\n"); 7856 return -EINVAL; 7857 } 7858 /* Set the read command byte count */ 7859 bnx2x_cl45_write(bp, phy, 7860 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, 7861 (byte_cnt | (dev_addr << 8))); 7862 7863 /* Set the read command address */ 7864 bnx2x_cl45_write(bp, phy, 7865 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, 7866 addr); 7867 7868 /* Activate read command */ 7869 bnx2x_cl45_write(bp, phy, 7870 MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, 7871 0x2c0f); 7872 7873 /* Wait up to 500us for command complete status */ 7874 for (i = 0; i < 100; i++) { 7875 bnx2x_cl45_read(bp, phy, 7876 MDIO_PMA_DEVAD, 7877 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); 7878 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == 7879 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) 7880 break; 7881 udelay(5); 7882 } 7883 7884 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) != 7885 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) { 7886 DP(NETIF_MSG_LINK, 7887 "Got bad status 0x%x when reading from SFP+ EEPROM\n", 7888 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK)); 7889 return -EINVAL; 7890 } 7891 7892 /* Read the buffer */ 7893 for (i = 0; i < byte_cnt; i++) { 7894 bnx2x_cl45_read(bp, phy, 7895 MDIO_PMA_DEVAD, 7896 MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val); 7897 o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK); 7898 } 7899 7900 for (i = 0; i < 100; i++) { 7901 bnx2x_cl45_read(bp, phy, 7902 MDIO_PMA_DEVAD, 7903 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); 7904 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == 7905 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) 7906 return 0; 7907 usleep_range(1000, 2000); 7908 } 7909 return -EINVAL; 7910} 7911 7912static void bnx2x_warpcore_power_module(struct link_params *params, 7913 u8 power) 7914{ 7915 u32 pin_cfg; 7916 struct bnx2x *bp = params->bp; 7917 7918 pin_cfg = (REG_RD(bp, params->shmem_base + 7919 offsetof(struct shmem_region, 7920 dev_info.port_hw_config[params->port].e3_sfp_ctrl)) & 7921 PORT_HW_CFG_E3_PWR_DIS_MASK) >> 7922 PORT_HW_CFG_E3_PWR_DIS_SHIFT; 7923 7924 if (pin_cfg == PIN_CFG_NA) 7925 return; 7926 DP(NETIF_MSG_LINK, "Setting SFP+ module power to %d using pin cfg %d\n", 7927 power, pin_cfg); 7928 /* Low ==> corresponding SFP+ module is powered 7929 * high ==> the SFP+ module is powered down 7930 */ 7931 bnx2x_set_cfg_pin(bp, pin_cfg, power ^ 1); 7932} 7933static int bnx2x_warpcore_read_sfp_module_eeprom(struct bnx2x_phy *phy, 7934 struct link_params *params, 7935 u8 dev_addr, 7936 u16 addr, u8 byte_cnt, 7937 u8 *o_buf, u8 is_init) 7938{ 7939 int rc = 0; 7940 u8 i, j = 0, cnt = 0; 7941 u32 data_array[4]; 7942 u16 addr32; 7943 struct bnx2x *bp = params->bp; 7944 7945 if (byte_cnt > SFP_EEPROM_PAGE_SIZE) { 7946 DP(NETIF_MSG_LINK, 7947 "Reading from eeprom is limited to 16 bytes\n"); 7948 return -EINVAL; 7949 } 7950 7951 /* 4 byte aligned address */ 7952 addr32 = addr & (~0x3); 7953 do { 7954 if ((!is_init) && (cnt == I2C_WA_PWR_ITER)) { 7955 bnx2x_warpcore_power_module(params, 0); 7956 /* Note that 100us are not enough here */ 7957 usleep_range(1000, 2000); 7958 bnx2x_warpcore_power_module(params, 1); 7959 } 7960 rc = bnx2x_bsc_read(params, bp, dev_addr, addr32, 0, byte_cnt, 7961 data_array); 7962 } while ((rc != 0) && (++cnt < I2C_WA_RETRY_CNT)); 7963 7964 if (rc == 0) { 7965 for (i = (addr - addr32); i < byte_cnt + (addr - addr32); i++) { 7966 o_buf[j] = *((u8 *)data_array + i); 7967 j++; 7968 } 7969 } 7970 7971 return rc; 7972} 7973 7974static int bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy, 7975 struct link_params *params, 7976 u8 dev_addr, u16 addr, u8 byte_cnt, 7977 u8 *o_buf, u8 is_init) 7978{ 7979 struct bnx2x *bp = params->bp; 7980 u16 val, i; 7981 7982 if (byte_cnt > SFP_EEPROM_PAGE_SIZE) { 7983 DP(NETIF_MSG_LINK, 7984 "Reading from eeprom is limited to 0xf\n"); 7985 return -EINVAL; 7986 } 7987 7988 /* Set 2-wire transfer rate of SFP+ module EEPROM 7989 * to 100Khz since some DACs(direct attached cables) do 7990 * not work at 400Khz. 7991 */ 7992 bnx2x_cl45_write(bp, phy, 7993 MDIO_PMA_DEVAD, 7994 MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR, 7995 ((dev_addr << 8) | 1)); 7996 7997 /* Need to read from 1.8000 to clear it */ 7998 bnx2x_cl45_read(bp, phy, 7999 MDIO_PMA_DEVAD, 8000 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, 8001 &val); 8002 8003 /* Set the read command byte count */ 8004 bnx2x_cl45_write(bp, phy, 8005 MDIO_PMA_DEVAD, 8006 MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, 8007 ((byte_cnt < 2) ? 2 : byte_cnt)); 8008 8009 /* Set the read command address */ 8010 bnx2x_cl45_write(bp, phy, 8011 MDIO_PMA_DEVAD, 8012 MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, 8013 addr); 8014 /* Set the destination address */ 8015 bnx2x_cl45_write(bp, phy, 8016 MDIO_PMA_DEVAD, 8017 0x8004, 8018 MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF); 8019 8020 /* Activate read command */ 8021 bnx2x_cl45_write(bp, phy, 8022 MDIO_PMA_DEVAD, 8023 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, 8024 0x8002); 8025 /* Wait appropriate time for two-wire command to finish before 8026 * polling the status register 8027 */ 8028 usleep_range(1000, 2000); 8029 8030 /* Wait up to 500us for command complete status */ 8031 for (i = 0; i < 100; i++) { 8032 bnx2x_cl45_read(bp, phy, 8033 MDIO_PMA_DEVAD, 8034 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); 8035 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == 8036 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) 8037 break; 8038 udelay(5); 8039 } 8040 8041 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) != 8042 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) { 8043 DP(NETIF_MSG_LINK, 8044 "Got bad status 0x%x when reading from SFP+ EEPROM\n", 8045 (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK)); 8046 return -EFAULT; 8047 } 8048 8049 /* Read the buffer */ 8050 for (i = 0; i < byte_cnt; i++) { 8051 bnx2x_cl45_read(bp, phy, 8052 MDIO_PMA_DEVAD, 8053 MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val); 8054 o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK); 8055 } 8056 8057 for (i = 0; i < 100; i++) { 8058 bnx2x_cl45_read(bp, phy, 8059 MDIO_PMA_DEVAD, 8060 MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); 8061 if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == 8062 MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) 8063 return 0; 8064 usleep_range(1000, 2000); 8065 } 8066 8067 return -EINVAL; 8068} 8069int bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy, 8070 struct link_params *params, u8 dev_addr, 8071 u16 addr, u16 byte_cnt, u8 *o_buf) 8072{ 8073 int rc = 0; 8074 struct bnx2x *bp = params->bp; 8075 u8 xfer_size; 8076 u8 *user_data = o_buf; 8077 read_sfp_module_eeprom_func_p read_func; 8078 8079 if ((dev_addr != 0xa0) && (dev_addr != 0xa2)) { 8080 DP(NETIF_MSG_LINK, "invalid dev_addr 0x%x\n", dev_addr); 8081 return -EINVAL; 8082 } 8083 8084 switch (phy->type) { 8085 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: 8086 read_func = bnx2x_8726_read_sfp_module_eeprom; 8087 break; 8088 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: 8089 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722: 8090 read_func = bnx2x_8727_read_sfp_module_eeprom; 8091 break; 8092 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: 8093 read_func = bnx2x_warpcore_read_sfp_module_eeprom; 8094 break; 8095 default: 8096 return -EOPNOTSUPP; 8097 } 8098 8099 while (!rc && (byte_cnt > 0)) { 8100 xfer_size = (byte_cnt > SFP_EEPROM_PAGE_SIZE) ? 8101 SFP_EEPROM_PAGE_SIZE : byte_cnt; 8102 rc = read_func(phy, params, dev_addr, addr, xfer_size, 8103 user_data, 0); 8104 byte_cnt -= xfer_size; 8105 user_data += xfer_size; 8106 addr += xfer_size; 8107 } 8108 return rc; 8109} 8110 8111static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, 8112 struct link_params *params, 8113 u16 *edc_mode) 8114{ 8115 struct bnx2x *bp = params->bp; 8116 u32 sync_offset = 0, phy_idx, media_types; 8117 u8 val[SFP_EEPROM_FC_TX_TECH_ADDR + 1], check_limiting_mode = 0; 8118 *edc_mode = EDC_MODE_LIMITING; 8119 phy->media_type = ETH_PHY_UNSPECIFIED; 8120 /* First check for copper cable */ 8121 if (bnx2x_read_sfp_module_eeprom(phy, 8122 params, 8123 I2C_DEV_ADDR_A0, 8124 0, 8125 SFP_EEPROM_FC_TX_TECH_ADDR + 1, 8126 (u8 *)val) != 0) { 8127 DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n"); 8128 return -EINVAL; 8129 } 8130 params->link_attr_sync &= ~LINK_SFP_EEPROM_COMP_CODE_MASK; 8131 params->link_attr_sync |= val[SFP_EEPROM_10G_COMP_CODE_ADDR] << 8132 LINK_SFP_EEPROM_COMP_CODE_SHIFT; 8133 bnx2x_update_link_attr(params, params->link_attr_sync); 8134 switch (val[SFP_EEPROM_CON_TYPE_ADDR]) { 8135 case SFP_EEPROM_CON_TYPE_VAL_COPPER: 8136 { 8137 u8 copper_module_type; 8138 phy->media_type = ETH_PHY_DA_TWINAX; 8139 /* Check if its active cable (includes SFP+ module) 8140 * of passive cable 8141 */ 8142 copper_module_type = val[SFP_EEPROM_FC_TX_TECH_ADDR]; 8143 8144 if (copper_module_type & 8145 SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) { 8146 DP(NETIF_MSG_LINK, "Active Copper cable detected\n"); 8147 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) 8148 *edc_mode = EDC_MODE_ACTIVE_DAC; 8149 else 8150 check_limiting_mode = 1; 8151 } else { 8152 *edc_mode = EDC_MODE_PASSIVE_DAC; 8153 /* Even in case PASSIVE_DAC indication is not set, 8154 * treat it as a passive DAC cable, since some cables 8155 * don't have this indication. 8156 */ 8157 if (copper_module_type & 8158 SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE) { 8159 DP(NETIF_MSG_LINK, 8160 "Passive Copper cable detected\n"); 8161 } else { 8162 DP(NETIF_MSG_LINK, 8163 "Unknown copper-cable-type\n"); 8164 } 8165 } 8166 break; 8167 } 8168 case SFP_EEPROM_CON_TYPE_VAL_UNKNOWN: 8169 case SFP_EEPROM_CON_TYPE_VAL_LC: 8170 case SFP_EEPROM_CON_TYPE_VAL_RJ45: 8171 check_limiting_mode = 1; 8172 if (((val[SFP_EEPROM_10G_COMP_CODE_ADDR] & 8173 (SFP_EEPROM_10G_COMP_CODE_SR_MASK | 8174 SFP_EEPROM_10G_COMP_CODE_LR_MASK | 8175 SFP_EEPROM_10G_COMP_CODE_LRM_MASK)) == 0) && 8176 (val[SFP_EEPROM_1G_COMP_CODE_ADDR] != 0)) { 8177 DP(NETIF_MSG_LINK, "1G SFP module detected\n"); 8178 phy->media_type = ETH_PHY_SFP_1G_FIBER; 8179 if (phy->req_line_speed != SPEED_1000) { 8180 u8 gport = params->port; 8181 phy->req_line_speed = SPEED_1000; 8182 if (!CHIP_IS_E1x(bp)) { 8183 gport = BP_PATH(bp) + 8184 (params->port << 1); 8185 } 8186 netdev_err(bp->dev, 8187 "Warning: Link speed was forced to 1000Mbps. Current SFP module in port %d is not compliant with 10G Ethernet\n", 8188 gport); 8189 } 8190 if (val[SFP_EEPROM_1G_COMP_CODE_ADDR] & 8191 SFP_EEPROM_1G_COMP_CODE_BASE_T) { 8192 bnx2x_sfp_set_transmitter(params, phy, 0); 8193 msleep(40); 8194 bnx2x_sfp_set_transmitter(params, phy, 1); 8195 } 8196 } else { 8197 int idx, cfg_idx = 0; 8198 DP(NETIF_MSG_LINK, "10G Optic module detected\n"); 8199 for (idx = INT_PHY; idx < MAX_PHYS; idx++) { 8200 if (params->phy[idx].type == phy->type) { 8201 cfg_idx = LINK_CONFIG_IDX(idx); 8202 break; 8203 } 8204 } 8205 phy->media_type = ETH_PHY_SFPP_10G_FIBER; 8206 phy->req_line_speed = params->req_line_speed[cfg_idx]; 8207 } 8208 break; 8209 default: 8210 DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n", 8211 val[SFP_EEPROM_CON_TYPE_ADDR]); 8212 return -EINVAL; 8213 } 8214 sync_offset = params->shmem_base + 8215 offsetof(struct shmem_region, 8216 dev_info.port_hw_config[params->port].media_type); 8217 media_types = REG_RD(bp, sync_offset); 8218 /* Update media type for non-PMF sync */ 8219 for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) { 8220 if (&(params->phy[phy_idx]) == phy) { 8221 media_types &= ~(PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK << 8222 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx)); 8223 media_types |= ((phy->media_type & 8224 PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) << 8225 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx)); 8226 break; 8227 } 8228 } 8229 REG_WR(bp, sync_offset, media_types); 8230 if (check_limiting_mode) { 8231 u8 options[SFP_EEPROM_OPTIONS_SIZE]; 8232 if (bnx2x_read_sfp_module_eeprom(phy, 8233 params, 8234 I2C_DEV_ADDR_A0, 8235 SFP_EEPROM_OPTIONS_ADDR, 8236 SFP_EEPROM_OPTIONS_SIZE, 8237 options) != 0) { 8238 DP(NETIF_MSG_LINK, 8239 "Failed to read Option field from module EEPROM\n"); 8240 return -EINVAL; 8241 } 8242 if ((options[0] & SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK)) 8243 *edc_mode = EDC_MODE_LINEAR; 8244 else 8245 *edc_mode = EDC_MODE_LIMITING; 8246 } 8247 DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode); 8248 return 0; 8249} 8250/* This function read the relevant field from the module (SFP+), and verify it 8251 * is compliant with this board 8252 */ 8253static int bnx2x_verify_sfp_module(struct bnx2x_phy *phy, 8254 struct link_params *params) 8255{ 8256 struct bnx2x *bp = params->bp; 8257 u32 val, cmd; 8258 u32 fw_resp, fw_cmd_param; 8259 char vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE+1]; 8260 char vendor_pn[SFP_EEPROM_PART_NO_SIZE+1]; 8261 phy->flags &= ~FLAGS_SFP_NOT_APPROVED; 8262 val = REG_RD(bp, params->shmem_base + 8263 offsetof(struct shmem_region, dev_info. 8264 port_feature_config[params->port].config)); 8265 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == 8266 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT) { 8267 DP(NETIF_MSG_LINK, "NOT enforcing module verification\n"); 8268 return 0; 8269 } 8270 8271 if (params->feature_config_flags & 8272 FEATURE_CONFIG_BC_SUPPORTS_DUAL_PHY_OPT_MDL_VRFY) { 8273 /* Use specific phy request */ 8274 cmd = DRV_MSG_CODE_VRFY_SPECIFIC_PHY_OPT_MDL; 8275 } else if (params->feature_config_flags & 8276 FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY) { 8277 /* Use first phy request only in case of non-dual media*/ 8278 if (DUAL_MEDIA(params)) { 8279 DP(NETIF_MSG_LINK, 8280 "FW does not support OPT MDL verification\n"); 8281 return -EINVAL; 8282 } 8283 cmd = DRV_MSG_CODE_VRFY_FIRST_PHY_OPT_MDL; 8284 } else { 8285 /* No support in OPT MDL detection */ 8286 DP(NETIF_MSG_LINK, 8287 "FW does not support OPT MDL verification\n"); 8288 return -EINVAL; 8289 } 8290 8291 fw_cmd_param = FW_PARAM_SET(phy->addr, phy->type, phy->mdio_ctrl); 8292 fw_resp = bnx2x_fw_command(bp, cmd, fw_cmd_param); 8293 if (fw_resp == FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS) { 8294 DP(NETIF_MSG_LINK, "Approved module\n"); 8295 return 0; 8296 } 8297 8298 /* Format the warning message */ 8299 if (bnx2x_read_sfp_module_eeprom(phy, 8300 params, 8301 I2C_DEV_ADDR_A0, 8302 SFP_EEPROM_VENDOR_NAME_ADDR, 8303 SFP_EEPROM_VENDOR_NAME_SIZE, 8304 (u8 *)vendor_name)) 8305 vendor_name[0] = '\0'; 8306 else 8307 vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0'; 8308 if (bnx2x_read_sfp_module_eeprom(phy, 8309 params, 8310 I2C_DEV_ADDR_A0, 8311 SFP_EEPROM_PART_NO_ADDR, 8312 SFP_EEPROM_PART_NO_SIZE, 8313 (u8 *)vendor_pn)) 8314 vendor_pn[0] = '\0'; 8315 else 8316 vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0'; 8317 8318 netdev_err(bp->dev, "Warning: Unqualified SFP+ module detected," 8319 " Port %d from %s part number %s\n", 8320 params->port, vendor_name, vendor_pn); 8321 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) != 8322 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_WARNING_MSG) 8323 phy->flags |= FLAGS_SFP_NOT_APPROVED; 8324 return -EINVAL; 8325} 8326 8327static int bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy, 8328 struct link_params *params) 8329 8330{ 8331 u8 val; 8332 int rc; 8333 struct bnx2x *bp = params->bp; 8334 u16 timeout; 8335 /* Initialization time after hot-plug may take up to 300ms for 8336 * some phys type ( e.g. JDSU ) 8337 */ 8338 8339 for (timeout = 0; timeout < 60; timeout++) { 8340 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) 8341 rc = bnx2x_warpcore_read_sfp_module_eeprom( 8342 phy, params, I2C_DEV_ADDR_A0, 1, 1, &val, 8343 1); 8344 else 8345 rc = bnx2x_read_sfp_module_eeprom(phy, params, 8346 I2C_DEV_ADDR_A0, 8347 1, 1, &val); 8348 if (rc == 0) { 8349 DP(NETIF_MSG_LINK, 8350 "SFP+ module initialization took %d ms\n", 8351 timeout * 5); 8352 return 0; 8353 } 8354 usleep_range(5000, 10000); 8355 } 8356 rc = bnx2x_read_sfp_module_eeprom(phy, params, I2C_DEV_ADDR_A0, 8357 1, 1, &val); 8358 return rc; 8359} 8360 8361static void bnx2x_8727_power_module(struct bnx2x *bp, 8362 struct bnx2x_phy *phy, 8363 u8 is_power_up) { 8364 /* Make sure GPIOs are not using for LED mode */ 8365 u16 val; 8366 /* In the GPIO register, bit 4 is use to determine if the GPIOs are 8367 * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for 8368 * output 8369 * Bits 0-1 determine the GPIOs value for OUTPUT in case bit 4 val is 0 8370 * Bits 8-9 determine the GPIOs value for INPUT in case bit 4 val is 1 8371 * where the 1st bit is the over-current(only input), and 2nd bit is 8372 * for power( only output ) 8373 * 8374 * In case of NOC feature is disabled and power is up, set GPIO control 8375 * as input to enable listening of over-current indication 8376 */ 8377 if (phy->flags & FLAGS_NOC) 8378 return; 8379 if (is_power_up) 8380 val = (1<<4); 8381 else 8382 /* Set GPIO control to OUTPUT, and set the power bit 8383 * to according to the is_power_up 8384 */ 8385 val = (1<<1); 8386 8387 bnx2x_cl45_write(bp, phy, 8388 MDIO_PMA_DEVAD, 8389 MDIO_PMA_REG_8727_GPIO_CTRL, 8390 val); 8391} 8392 8393static int bnx2x_8726_set_limiting_mode(struct bnx2x *bp, 8394 struct bnx2x_phy *phy, 8395 u16 edc_mode) 8396{ 8397 u16 cur_limiting_mode; 8398 8399 bnx2x_cl45_read(bp, phy, 8400 MDIO_PMA_DEVAD, 8401 MDIO_PMA_REG_ROM_VER2, 8402 &cur_limiting_mode); 8403 DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n", 8404 cur_limiting_mode); 8405 8406 if (edc_mode == EDC_MODE_LIMITING) { 8407 DP(NETIF_MSG_LINK, "Setting LIMITING MODE\n"); 8408 bnx2x_cl45_write(bp, phy, 8409 MDIO_PMA_DEVAD, 8410 MDIO_PMA_REG_ROM_VER2, 8411 EDC_MODE_LIMITING); 8412 } else { /* LRM mode ( default )*/ 8413 8414 DP(NETIF_MSG_LINK, "Setting LRM MODE\n"); 8415 8416 /* Changing to LRM mode takes quite few seconds. So do it only 8417 * if current mode is limiting (default is LRM) 8418 */ 8419 if (cur_limiting_mode != EDC_MODE_LIMITING) 8420 return 0; 8421 8422 bnx2x_cl45_write(bp, phy, 8423 MDIO_PMA_DEVAD, 8424 MDIO_PMA_REG_LRM_MODE, 8425 0); 8426 bnx2x_cl45_write(bp, phy, 8427 MDIO_PMA_DEVAD, 8428 MDIO_PMA_REG_ROM_VER2, 8429 0x128); 8430 bnx2x_cl45_write(bp, phy, 8431 MDIO_PMA_DEVAD, 8432 MDIO_PMA_REG_MISC_CTRL0, 8433 0x4008); 8434 bnx2x_cl45_write(bp, phy, 8435 MDIO_PMA_DEVAD, 8436 MDIO_PMA_REG_LRM_MODE, 8437 0xaaaa); 8438 } 8439 return 0; 8440} 8441 8442static int bnx2x_8727_set_limiting_mode(struct bnx2x *bp, 8443 struct bnx2x_phy *phy, 8444 u16 edc_mode) 8445{ 8446 u16 phy_identifier; 8447 u16 rom_ver2_val; 8448 bnx2x_cl45_read(bp, phy, 8449 MDIO_PMA_DEVAD, 8450 MDIO_PMA_REG_PHY_IDENTIFIER, 8451 &phy_identifier); 8452 8453 bnx2x_cl45_write(bp, phy, 8454 MDIO_PMA_DEVAD, 8455 MDIO_PMA_REG_PHY_IDENTIFIER, 8456 (phy_identifier & ~(1<<9))); 8457 8458 bnx2x_cl45_read(bp, phy, 8459 MDIO_PMA_DEVAD, 8460 MDIO_PMA_REG_ROM_VER2, 8461 &rom_ver2_val); 8462 /* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */ 8463 bnx2x_cl45_write(bp, phy, 8464 MDIO_PMA_DEVAD, 8465 MDIO_PMA_REG_ROM_VER2, 8466 (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff)); 8467 8468 bnx2x_cl45_write(bp, phy, 8469 MDIO_PMA_DEVAD, 8470 MDIO_PMA_REG_PHY_IDENTIFIER, 8471 (phy_identifier | (1<<9))); 8472 8473 return 0; 8474} 8475 8476static void bnx2x_8727_specific_func(struct bnx2x_phy *phy, 8477 struct link_params *params, 8478 u32 action) 8479{ 8480 struct bnx2x *bp = params->bp; 8481 u16 val; 8482 switch (action) { 8483 case DISABLE_TX: 8484 bnx2x_sfp_set_transmitter(params, phy, 0); 8485 break; 8486 case ENABLE_TX: 8487 if (!(phy->flags & FLAGS_SFP_NOT_APPROVED)) 8488 bnx2x_sfp_set_transmitter(params, phy, 1); 8489 break; 8490 case PHY_INIT: 8491 bnx2x_cl45_write(bp, phy, 8492 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, 8493 (1<<2) | (1<<5)); 8494 bnx2x_cl45_write(bp, phy, 8495 MDIO_PMA_DEVAD, MDIO_PMA_LASI_TXCTRL, 8496 0); 8497 bnx2x_cl45_write(bp, phy, 8498 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x0006); 8499 /* Make MOD_ABS give interrupt on change */ 8500 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 8501 MDIO_PMA_REG_8727_PCS_OPT_CTRL, 8502 &val); 8503 val |= (1<<12); 8504 if (phy->flags & FLAGS_NOC) 8505 val |= (3<<5); 8506 /* Set 8727 GPIOs to input to allow reading from the 8727 GPIO0 8507 * status which reflect SFP+ module over-current 8508 */ 8509 if (!(phy->flags & FLAGS_NOC)) 8510 val &= 0xff8f; /* Reset bits 4-6 */ 8511 bnx2x_cl45_write(bp, phy, 8512 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_OPT_CTRL, 8513 val); 8514 break; 8515 default: 8516 DP(NETIF_MSG_LINK, "Function 0x%x not supported by 8727\n", 8517 action); 8518 return; 8519 } 8520} 8521 8522static void bnx2x_set_e1e2_module_fault_led(struct link_params *params, 8523 u8 gpio_mode) 8524{ 8525 struct bnx2x *bp = params->bp; 8526 8527 u32 fault_led_gpio = REG_RD(bp, params->shmem_base + 8528 offsetof(struct shmem_region, 8529 dev_info.port_hw_config[params->port].sfp_ctrl)) & 8530 PORT_HW_CFG_FAULT_MODULE_LED_MASK; 8531 switch (fault_led_gpio) { 8532 case PORT_HW_CFG_FAULT_MODULE_LED_DISABLED: 8533 return; 8534 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO0: 8535 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO1: 8536 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO2: 8537 case PORT_HW_CFG_FAULT_MODULE_LED_GPIO3: 8538 { 8539 u8 gpio_port = bnx2x_get_gpio_port(params); 8540 u16 gpio_pin = fault_led_gpio - 8541 PORT_HW_CFG_FAULT_MODULE_LED_GPIO0; 8542 DP(NETIF_MSG_LINK, "Set fault module-detected led " 8543 "pin %x port %x mode %x\n", 8544 gpio_pin, gpio_port, gpio_mode); 8545 bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port); 8546 } 8547 break; 8548 default: 8549 DP(NETIF_MSG_LINK, "Error: Invalid fault led mode 0x%x\n", 8550 fault_led_gpio); 8551 } 8552} 8553 8554static void bnx2x_set_e3_module_fault_led(struct link_params *params, 8555 u8 gpio_mode) 8556{ 8557 u32 pin_cfg; 8558 u8 port = params->port; 8559 struct bnx2x *bp = params->bp; 8560 pin_cfg = (REG_RD(bp, params->shmem_base + 8561 offsetof(struct shmem_region, 8562 dev_info.port_hw_config[port].e3_sfp_ctrl)) & 8563 PORT_HW_CFG_E3_FAULT_MDL_LED_MASK) >> 8564 PORT_HW_CFG_E3_FAULT_MDL_LED_SHIFT; 8565 DP(NETIF_MSG_LINK, "Setting Fault LED to %d using pin cfg %d\n", 8566 gpio_mode, pin_cfg); 8567 bnx2x_set_cfg_pin(bp, pin_cfg, gpio_mode); 8568} 8569 8570static void bnx2x_set_sfp_module_fault_led(struct link_params *params, 8571 u8 gpio_mode) 8572{ 8573 struct bnx2x *bp = params->bp; 8574 DP(NETIF_MSG_LINK, "Setting SFP+ module fault LED to %d\n", gpio_mode); 8575 if (CHIP_IS_E3(bp)) { 8576 /* Low ==> if SFP+ module is supported otherwise 8577 * High ==> if SFP+ module is not on the approved vendor list 8578 */ 8579 bnx2x_set_e3_module_fault_led(params, gpio_mode); 8580 } else 8581 bnx2x_set_e1e2_module_fault_led(params, gpio_mode); 8582} 8583 8584static void bnx2x_warpcore_hw_reset(struct bnx2x_phy *phy, 8585 struct link_params *params) 8586{ 8587 struct bnx2x *bp = params->bp; 8588 bnx2x_warpcore_power_module(params, 0); 8589 /* Put Warpcore in low power mode */ 8590 REG_WR(bp, MISC_REG_WC0_RESET, 0x0c0e); 8591 8592 /* Put LCPLL in low power mode */ 8593 REG_WR(bp, MISC_REG_LCPLL_E40_PWRDWN, 1); 8594 REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_ANA, 0); 8595 REG_WR(bp, MISC_REG_LCPLL_E40_RESETB_DIG, 0); 8596} 8597 8598static void bnx2x_power_sfp_module(struct link_params *params, 8599 struct bnx2x_phy *phy, 8600 u8 power) 8601{ 8602 struct bnx2x *bp = params->bp; 8603 DP(NETIF_MSG_LINK, "Setting SFP+ power to %x\n", power); 8604 8605 switch (phy->type) { 8606 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: 8607 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722: 8608 bnx2x_8727_power_module(params->bp, phy, power); 8609 break; 8610 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: 8611 bnx2x_warpcore_power_module(params, power); 8612 break; 8613 default: 8614 break; 8615 } 8616} 8617static void bnx2x_warpcore_set_limiting_mode(struct link_params *params, 8618 struct bnx2x_phy *phy, 8619 u16 edc_mode) 8620{ 8621 u16 val = 0; 8622 u16 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT; 8623 struct bnx2x *bp = params->bp; 8624 8625 u8 lane = bnx2x_get_warpcore_lane(phy, params); 8626 /* This is a global register which controls all lanes */ 8627 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 8628 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, &val); 8629 val &= ~(0xf << (lane << 2)); 8630 8631 switch (edc_mode) { 8632 case EDC_MODE_LINEAR: 8633 case EDC_MODE_LIMITING: 8634 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT; 8635 break; 8636 case EDC_MODE_PASSIVE_DAC: 8637 case EDC_MODE_ACTIVE_DAC: 8638 mode = MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC; 8639 break; 8640 default: 8641 break; 8642 } 8643 8644 val |= (mode << (lane << 2)); 8645 bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD, 8646 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, val); 8647 /* A must read */ 8648 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 8649 MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE, &val); 8650 8651 /* Restart microcode to re-read the new mode */ 8652 bnx2x_warpcore_reset_lane(bp, phy, 1); 8653 bnx2x_warpcore_reset_lane(bp, phy, 0); 8654 8655} 8656 8657static void bnx2x_set_limiting_mode(struct link_params *params, 8658 struct bnx2x_phy *phy, 8659 u16 edc_mode) 8660{ 8661 switch (phy->type) { 8662 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: 8663 bnx2x_8726_set_limiting_mode(params->bp, phy, edc_mode); 8664 break; 8665 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: 8666 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722: 8667 bnx2x_8727_set_limiting_mode(params->bp, phy, edc_mode); 8668 break; 8669 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: 8670 bnx2x_warpcore_set_limiting_mode(params, phy, edc_mode); 8671 break; 8672 } 8673} 8674 8675static int bnx2x_sfp_module_detection(struct bnx2x_phy *phy, 8676 struct link_params *params) 8677{ 8678 struct bnx2x *bp = params->bp; 8679 u16 edc_mode; 8680 int rc = 0; 8681 8682 u32 val = REG_RD(bp, params->shmem_base + 8683 offsetof(struct shmem_region, dev_info. 8684 port_feature_config[params->port].config)); 8685 /* Enabled transmitter by default */ 8686 bnx2x_sfp_set_transmitter(params, phy, 1); 8687 DP(NETIF_MSG_LINK, "SFP+ module plugged in/out detected on port %d\n", 8688 params->port); 8689 /* Power up module */ 8690 bnx2x_power_sfp_module(params, phy, 1); 8691 if (bnx2x_get_edc_mode(phy, params, &edc_mode) != 0) { 8692 DP(NETIF_MSG_LINK, "Failed to get valid module type\n"); 8693 return -EINVAL; 8694 } else if (bnx2x_verify_sfp_module(phy, params) != 0) { 8695 /* Check SFP+ module compatibility */ 8696 DP(NETIF_MSG_LINK, "Module verification failed!!\n"); 8697 rc = -EINVAL; 8698 /* Turn on fault module-detected led */ 8699 bnx2x_set_sfp_module_fault_led(params, 8700 MISC_REGISTERS_GPIO_HIGH); 8701 8702 /* Check if need to power down the SFP+ module */ 8703 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == 8704 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN) { 8705 DP(NETIF_MSG_LINK, "Shutdown SFP+ module!!\n"); 8706 bnx2x_power_sfp_module(params, phy, 0); 8707 return rc; 8708 } 8709 } else { 8710 /* Turn off fault module-detected led */ 8711 bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_LOW); 8712 } 8713 8714 /* Check and set limiting mode / LRM mode on 8726. On 8727 it 8715 * is done automatically 8716 */ 8717 bnx2x_set_limiting_mode(params, phy, edc_mode); 8718 8719 /* Disable transmit for this module if the module is not approved, and 8720 * laser needs to be disabled. 8721 */ 8722 if ((rc) && 8723 ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == 8724 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)) 8725 bnx2x_sfp_set_transmitter(params, phy, 0); 8726 8727 return rc; 8728} 8729 8730void bnx2x_handle_module_detect_int(struct link_params *params) 8731{ 8732 struct bnx2x *bp = params->bp; 8733 struct bnx2x_phy *phy; 8734 u32 gpio_val; 8735 u8 gpio_num, gpio_port; 8736 if (CHIP_IS_E3(bp)) { 8737 phy = ¶ms->phy[INT_PHY]; 8738 /* Always enable TX laser,will be disabled in case of fault */ 8739 bnx2x_sfp_set_transmitter(params, phy, 1); 8740 } else { 8741 phy = ¶ms->phy[EXT_PHY1]; 8742 } 8743 if (bnx2x_get_mod_abs_int_cfg(bp, params->chip_id, params->shmem_base, 8744 params->port, &gpio_num, &gpio_port) == 8745 -EINVAL) { 8746 DP(NETIF_MSG_LINK, "Failed to get MOD_ABS interrupt config\n"); 8747 return; 8748 } 8749 8750 /* Set valid module led off */ 8751 bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_HIGH); 8752 8753 /* Get current gpio val reflecting module plugged in / out*/ 8754 gpio_val = bnx2x_get_gpio(bp, gpio_num, gpio_port); 8755 8756 /* Call the handling function in case module is detected */ 8757 if (gpio_val == 0) { 8758 bnx2x_set_mdio_emac_per_phy(bp, params); 8759 bnx2x_set_aer_mmd(params, phy); 8760 8761 bnx2x_power_sfp_module(params, phy, 1); 8762 bnx2x_set_gpio_int(bp, gpio_num, 8763 MISC_REGISTERS_GPIO_INT_OUTPUT_CLR, 8764 gpio_port); 8765 if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) { 8766 bnx2x_sfp_module_detection(phy, params); 8767 if (CHIP_IS_E3(bp)) { 8768 u16 rx_tx_in_reset; 8769 /* In case WC is out of reset, reconfigure the 8770 * link speed while taking into account 1G 8771 * module limitation. 8772 */ 8773 bnx2x_cl45_read(bp, phy, 8774 MDIO_WC_DEVAD, 8775 MDIO_WC_REG_DIGITAL5_MISC6, 8776 &rx_tx_in_reset); 8777 if ((!rx_tx_in_reset) && 8778 (params->link_flags & 8779 PHY_INITIALIZED)) { 8780 bnx2x_warpcore_reset_lane(bp, phy, 1); 8781 bnx2x_warpcore_config_sfi(phy, params); 8782 bnx2x_warpcore_reset_lane(bp, phy, 0); 8783 } 8784 } 8785 } else { 8786 DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); 8787 } 8788 } else { 8789 bnx2x_set_gpio_int(bp, gpio_num, 8790 MISC_REGISTERS_GPIO_INT_OUTPUT_SET, 8791 gpio_port); 8792 /* Module was plugged out. 8793 * Disable transmit for this module 8794 */ 8795 phy->media_type = ETH_PHY_NOT_PRESENT; 8796 } 8797} 8798 8799/******************************************************************/ 8800/* Used by 8706 and 8727 */ 8801/******************************************************************/ 8802static void bnx2x_sfp_mask_fault(struct bnx2x *bp, 8803 struct bnx2x_phy *phy, 8804 u16 alarm_status_offset, 8805 u16 alarm_ctrl_offset) 8806{ 8807 u16 alarm_status, val; 8808 bnx2x_cl45_read(bp, phy, 8809 MDIO_PMA_DEVAD, alarm_status_offset, 8810 &alarm_status); 8811 bnx2x_cl45_read(bp, phy, 8812 MDIO_PMA_DEVAD, alarm_status_offset, 8813 &alarm_status); 8814 /* Mask or enable the fault event. */ 8815 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, alarm_ctrl_offset, &val); 8816 if (alarm_status & (1<<0)) 8817 val &= ~(1<<0); 8818 else 8819 val |= (1<<0); 8820 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, alarm_ctrl_offset, val); 8821} 8822/******************************************************************/ 8823/* common BCM8706/BCM8726 PHY SECTION */ 8824/******************************************************************/ 8825static u8 bnx2x_8706_8726_read_status(struct bnx2x_phy *phy, 8826 struct link_params *params, 8827 struct link_vars *vars) 8828{ 8829 u8 link_up = 0; 8830 u16 val1, val2, rx_sd, pcs_status; 8831 struct bnx2x *bp = params->bp; 8832 DP(NETIF_MSG_LINK, "XGXS 8706/8726\n"); 8833 /* Clear RX Alarm*/ 8834 bnx2x_cl45_read(bp, phy, 8835 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &val2); 8836 8837 bnx2x_sfp_mask_fault(bp, phy, MDIO_PMA_LASI_TXSTAT, 8838 MDIO_PMA_LASI_TXCTRL); 8839 8840 /* Clear LASI indication*/ 8841 bnx2x_cl45_read(bp, phy, 8842 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1); 8843 bnx2x_cl45_read(bp, phy, 8844 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val2); 8845 DP(NETIF_MSG_LINK, "8706/8726 LASI status 0x%x--> 0x%x\n", val1, val2); 8846 8847 bnx2x_cl45_read(bp, phy, 8848 MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_SD, &rx_sd); 8849 bnx2x_cl45_read(bp, phy, 8850 MDIO_PCS_DEVAD, MDIO_PCS_REG_STATUS, &pcs_status); 8851 bnx2x_cl45_read(bp, phy, 8852 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2); 8853 bnx2x_cl45_read(bp, phy, 8854 MDIO_AN_DEVAD, MDIO_AN_REG_LINK_STATUS, &val2); 8855 8856 DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x pcs_status 0x%x 1Gbps" 8857 " link_status 0x%x\n", rx_sd, pcs_status, val2); 8858 /* Link is up if both bit 0 of pmd_rx_sd and bit 0 of pcs_status 8859 * are set, or if the autoneg bit 1 is set 8860 */ 8861 link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1))); 8862 if (link_up) { 8863 if (val2 & (1<<1)) 8864 vars->line_speed = SPEED_1000; 8865 else 8866 vars->line_speed = SPEED_10000; 8867 bnx2x_ext_phy_resolve_fc(phy, params, vars); 8868 vars->duplex = DUPLEX_FULL; 8869 } 8870 8871 /* Capture 10G link fault. Read twice to clear stale value. */ 8872 if (vars->line_speed == SPEED_10000) { 8873 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 8874 MDIO_PMA_LASI_TXSTAT, &val1); 8875 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 8876 MDIO_PMA_LASI_TXSTAT, &val1); 8877 if (val1 & (1<<0)) 8878 vars->fault_detected = 1; 8879 } 8880 8881 return link_up; 8882} 8883 8884/******************************************************************/ 8885/* BCM8706 PHY SECTION */ 8886/******************************************************************/ 8887static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy, 8888 struct link_params *params, 8889 struct link_vars *vars) 8890{ 8891 u32 tx_en_mode; 8892 u16 cnt, val, tmp1; 8893 struct bnx2x *bp = params->bp; 8894 8895 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 8896 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); 8897 /* HW reset */ 8898 bnx2x_ext_phy_hw_reset(bp, params->port); 8899 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040); 8900 bnx2x_wait_reset_complete(bp, phy, params); 8901 8902 /* Wait until fw is loaded */ 8903 for (cnt = 0; cnt < 100; cnt++) { 8904 bnx2x_cl45_read(bp, phy, 8905 MDIO_PMA_DEVAD, MDIO_PMA_REG_ROM_VER1, &val); 8906 if (val) 8907 break; 8908 usleep_range(10000, 20000); 8909 } 8910 DP(NETIF_MSG_LINK, "XGXS 8706 is initialized after %d ms\n", cnt); 8911 if ((params->feature_config_flags & 8912 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { 8913 u8 i; 8914 u16 reg; 8915 for (i = 0; i < 4; i++) { 8916 reg = MDIO_XS_8706_REG_BANK_RX0 + 8917 i*(MDIO_XS_8706_REG_BANK_RX1 - 8918 MDIO_XS_8706_REG_BANK_RX0); 8919 bnx2x_cl45_read(bp, phy, MDIO_XS_DEVAD, reg, &val); 8920 /* Clear first 3 bits of the control */ 8921 val &= ~0x7; 8922 /* Set control bits according to configuration */ 8923 val |= (phy->rx_preemphasis[i] & 0x7); 8924 DP(NETIF_MSG_LINK, "Setting RX Equalizer to BCM8706" 8925 " reg 0x%x <-- val 0x%x\n", reg, val); 8926 bnx2x_cl45_write(bp, phy, MDIO_XS_DEVAD, reg, val); 8927 } 8928 } 8929 /* Force speed */ 8930 if (phy->req_line_speed == SPEED_10000) { 8931 DP(NETIF_MSG_LINK, "XGXS 8706 force 10Gbps\n"); 8932 8933 bnx2x_cl45_write(bp, phy, 8934 MDIO_PMA_DEVAD, 8935 MDIO_PMA_REG_DIGITAL_CTRL, 0x400); 8936 bnx2x_cl45_write(bp, phy, 8937 MDIO_PMA_DEVAD, MDIO_PMA_LASI_TXCTRL, 8938 0); 8939 /* Arm LASI for link and Tx fault. */ 8940 bnx2x_cl45_write(bp, phy, 8941 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 3); 8942 } else { 8943 /* Force 1Gbps using autoneg with 1G advertisement */ 8944 8945 /* Allow CL37 through CL73 */ 8946 DP(NETIF_MSG_LINK, "XGXS 8706 AutoNeg\n"); 8947 bnx2x_cl45_write(bp, phy, 8948 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c); 8949 8950 /* Enable Full-Duplex advertisement on CL37 */ 8951 bnx2x_cl45_write(bp, phy, 8952 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LP, 0x0020); 8953 /* Enable CL37 AN */ 8954 bnx2x_cl45_write(bp, phy, 8955 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); 8956 /* 1G support */ 8957 bnx2x_cl45_write(bp, phy, 8958 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, (1<<5)); 8959 8960 /* Enable clause 73 AN */ 8961 bnx2x_cl45_write(bp, phy, 8962 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200); 8963 bnx2x_cl45_write(bp, phy, 8964 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, 8965 0x0400); 8966 bnx2x_cl45_write(bp, phy, 8967 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 8968 0x0004); 8969 } 8970 bnx2x_save_bcm_spirom_ver(bp, phy, params->port); 8971 8972 /* If TX Laser is controlled by GPIO_0, do not let PHY go into low 8973 * power mode, if TX Laser is disabled 8974 */ 8975 8976 tx_en_mode = REG_RD(bp, params->shmem_base + 8977 offsetof(struct shmem_region, 8978 dev_info.port_hw_config[params->port].sfp_ctrl)) 8979 & PORT_HW_CFG_TX_LASER_MASK; 8980 8981 if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) { 8982 DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n"); 8983 bnx2x_cl45_read(bp, phy, 8984 MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, &tmp1); 8985 tmp1 |= 0x1; 8986 bnx2x_cl45_write(bp, phy, 8987 MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, tmp1); 8988 } 8989 8990 return 0; 8991} 8992 8993static int bnx2x_8706_read_status(struct bnx2x_phy *phy, 8994 struct link_params *params, 8995 struct link_vars *vars) 8996{ 8997 return bnx2x_8706_8726_read_status(phy, params, vars); 8998} 8999 9000/******************************************************************/ 9001/* BCM8726 PHY SECTION */ 9002/******************************************************************/ 9003static void bnx2x_8726_config_loopback(struct bnx2x_phy *phy, 9004 struct link_params *params) 9005{ 9006 struct bnx2x *bp = params->bp; 9007 DP(NETIF_MSG_LINK, "PMA/PMD ext_phy_loopback: 8726\n"); 9008 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0001); 9009} 9010 9011static void bnx2x_8726_external_rom_boot(struct bnx2x_phy *phy, 9012 struct link_params *params) 9013{ 9014 struct bnx2x *bp = params->bp; 9015 /* Need to wait 100ms after reset */ 9016 msleep(100); 9017 9018 /* Micro controller re-boot */ 9019 bnx2x_cl45_write(bp, phy, 9020 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x018B); 9021 9022 /* Set soft reset */ 9023 bnx2x_cl45_write(bp, phy, 9024 MDIO_PMA_DEVAD, 9025 MDIO_PMA_REG_GEN_CTRL, 9026 MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); 9027 9028 bnx2x_cl45_write(bp, phy, 9029 MDIO_PMA_DEVAD, 9030 MDIO_PMA_REG_MISC_CTRL1, 0x0001); 9031 9032 bnx2x_cl45_write(bp, phy, 9033 MDIO_PMA_DEVAD, 9034 MDIO_PMA_REG_GEN_CTRL, 9035 MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); 9036 9037 /* Wait for 150ms for microcode load */ 9038 msleep(150); 9039 9040 /* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */ 9041 bnx2x_cl45_write(bp, phy, 9042 MDIO_PMA_DEVAD, 9043 MDIO_PMA_REG_MISC_CTRL1, 0x0000); 9044 9045 msleep(200); 9046 bnx2x_save_bcm_spirom_ver(bp, phy, params->port); 9047} 9048 9049static u8 bnx2x_8726_read_status(struct bnx2x_phy *phy, 9050 struct link_params *params, 9051 struct link_vars *vars) 9052{ 9053 struct bnx2x *bp = params->bp; 9054 u16 val1; 9055 u8 link_up = bnx2x_8706_8726_read_status(phy, params, vars); 9056 if (link_up) { 9057 bnx2x_cl45_read(bp, phy, 9058 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 9059 &val1); 9060 if (val1 & (1<<15)) { 9061 DP(NETIF_MSG_LINK, "Tx is disabled\n"); 9062 link_up = 0; 9063 vars->line_speed = 0; 9064 } 9065 } 9066 return link_up; 9067} 9068 9069 9070static int bnx2x_8726_config_init(struct bnx2x_phy *phy, 9071 struct link_params *params, 9072 struct link_vars *vars) 9073{ 9074 struct bnx2x *bp = params->bp; 9075 DP(NETIF_MSG_LINK, "Initializing BCM8726\n"); 9076 9077 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); 9078 bnx2x_wait_reset_complete(bp, phy, params); 9079 9080 bnx2x_8726_external_rom_boot(phy, params); 9081 9082 /* Need to call module detected on initialization since the module 9083 * detection triggered by actual module insertion might occur before 9084 * driver is loaded, and when driver is loaded, it reset all 9085 * registers, including the transmitter 9086 */ 9087 bnx2x_sfp_module_detection(phy, params); 9088 9089 if (phy->req_line_speed == SPEED_1000) { 9090 DP(NETIF_MSG_LINK, "Setting 1G force\n"); 9091 bnx2x_cl45_write(bp, phy, 9092 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40); 9093 bnx2x_cl45_write(bp, phy, 9094 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD); 9095 bnx2x_cl45_write(bp, phy, 9096 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x5); 9097 bnx2x_cl45_write(bp, phy, 9098 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, 9099 0x400); 9100 } else if ((phy->req_line_speed == SPEED_AUTO_NEG) && 9101 (phy->speed_cap_mask & 9102 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) && 9103 ((phy->speed_cap_mask & 9104 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) != 9105 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { 9106 DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); 9107 /* Set Flow control */ 9108 bnx2x_ext_phy_set_pause(params, phy, vars); 9109 bnx2x_cl45_write(bp, phy, 9110 MDIO_AN_DEVAD, MDIO_AN_REG_ADV, 0x20); 9111 bnx2x_cl45_write(bp, phy, 9112 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_CL73, 0x040c); 9113 bnx2x_cl45_write(bp, phy, 9114 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_FC_LD, 0x0020); 9115 bnx2x_cl45_write(bp, phy, 9116 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); 9117 bnx2x_cl45_write(bp, phy, 9118 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200); 9119 /* Enable RX-ALARM control to receive interrupt for 1G speed 9120 * change 9121 */ 9122 bnx2x_cl45_write(bp, phy, 9123 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x4); 9124 bnx2x_cl45_write(bp, phy, 9125 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, 9126 0x400); 9127 9128 } else { /* Default 10G. Set only LASI control */ 9129 bnx2x_cl45_write(bp, phy, 9130 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 1); 9131 } 9132 9133 /* Set TX PreEmphasis if needed */ 9134 if ((params->feature_config_flags & 9135 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { 9136 DP(NETIF_MSG_LINK, 9137 "Setting TX_CTRL1 0x%x, TX_CTRL2 0x%x\n", 9138 phy->tx_preemphasis[0], 9139 phy->tx_preemphasis[1]); 9140 bnx2x_cl45_write(bp, phy, 9141 MDIO_PMA_DEVAD, 9142 MDIO_PMA_REG_8726_TX_CTRL1, 9143 phy->tx_preemphasis[0]); 9144 9145 bnx2x_cl45_write(bp, phy, 9146 MDIO_PMA_DEVAD, 9147 MDIO_PMA_REG_8726_TX_CTRL2, 9148 phy->tx_preemphasis[1]); 9149 } 9150 9151 return 0; 9152 9153} 9154 9155static void bnx2x_8726_link_reset(struct bnx2x_phy *phy, 9156 struct link_params *params) 9157{ 9158 struct bnx2x *bp = params->bp; 9159 DP(NETIF_MSG_LINK, "bnx2x_8726_link_reset port %d\n", params->port); 9160 /* Set serial boot control for external load */ 9161 bnx2x_cl45_write(bp, phy, 9162 MDIO_PMA_DEVAD, 9163 MDIO_PMA_REG_GEN_CTRL, 0x0001); 9164} 9165 9166/******************************************************************/ 9167/* BCM8727 PHY SECTION */ 9168/******************************************************************/ 9169 9170static void bnx2x_8727_set_link_led(struct bnx2x_phy *phy, 9171 struct link_params *params, u8 mode) 9172{ 9173 struct bnx2x *bp = params->bp; 9174 u16 led_mode_bitmask = 0; 9175 u16 gpio_pins_bitmask = 0; 9176 u16 val; 9177 /* Only NOC flavor requires to set the LED specifically */ 9178 if (!(phy->flags & FLAGS_NOC)) 9179 return; 9180 switch (mode) { 9181 case LED_MODE_FRONT_PANEL_OFF: 9182 case LED_MODE_OFF: 9183 led_mode_bitmask = 0; 9184 gpio_pins_bitmask = 0x03; 9185 break; 9186 case LED_MODE_ON: 9187 led_mode_bitmask = 0; 9188 gpio_pins_bitmask = 0x02; 9189 break; 9190 case LED_MODE_OPER: 9191 led_mode_bitmask = 0x60; 9192 gpio_pins_bitmask = 0x11; 9193 break; 9194 } 9195 bnx2x_cl45_read(bp, phy, 9196 MDIO_PMA_DEVAD, 9197 MDIO_PMA_REG_8727_PCS_OPT_CTRL, 9198 &val); 9199 val &= 0xff8f; 9200 val |= led_mode_bitmask; 9201 bnx2x_cl45_write(bp, phy, 9202 MDIO_PMA_DEVAD, 9203 MDIO_PMA_REG_8727_PCS_OPT_CTRL, 9204 val); 9205 bnx2x_cl45_read(bp, phy, 9206 MDIO_PMA_DEVAD, 9207 MDIO_PMA_REG_8727_GPIO_CTRL, 9208 &val); 9209 val &= 0xffe0; 9210 val |= gpio_pins_bitmask; 9211 bnx2x_cl45_write(bp, phy, 9212 MDIO_PMA_DEVAD, 9213 MDIO_PMA_REG_8727_GPIO_CTRL, 9214 val); 9215} 9216static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy, 9217 struct link_params *params) { 9218 u32 swap_val, swap_override; 9219 u8 port; 9220 /* The PHY reset is controlled by GPIO 1. Fake the port number 9221 * to cancel the swap done in set_gpio() 9222 */ 9223 struct bnx2x *bp = params->bp; 9224 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); 9225 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); 9226 port = (swap_val && swap_override) ^ 1; 9227 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, 9228 MISC_REGISTERS_GPIO_OUTPUT_LOW, port); 9229} 9230 9231static void bnx2x_8727_config_speed(struct bnx2x_phy *phy, 9232 struct link_params *params) 9233{ 9234 struct bnx2x *bp = params->bp; 9235 u16 tmp1, val; 9236 /* Set option 1G speed */ 9237 if ((phy->req_line_speed == SPEED_1000) || 9238 (phy->media_type == ETH_PHY_SFP_1G_FIBER)) { 9239 DP(NETIF_MSG_LINK, "Setting 1G force\n"); 9240 bnx2x_cl45_write(bp, phy, 9241 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40); 9242 bnx2x_cl45_write(bp, phy, 9243 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD); 9244 bnx2x_cl45_read(bp, phy, 9245 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1); 9246 DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1); 9247 /* Power down the XAUI until link is up in case of dual-media 9248 * and 1G 9249 */ 9250 if (DUAL_MEDIA(params)) { 9251 bnx2x_cl45_read(bp, phy, 9252 MDIO_PMA_DEVAD, 9253 MDIO_PMA_REG_8727_PCS_GP, &val); 9254 val |= (3<<10); 9255 bnx2x_cl45_write(bp, phy, 9256 MDIO_PMA_DEVAD, 9257 MDIO_PMA_REG_8727_PCS_GP, val); 9258 } 9259 } else if ((phy->req_line_speed == SPEED_AUTO_NEG) && 9260 ((phy->speed_cap_mask & 9261 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) && 9262 ((phy->speed_cap_mask & 9263 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) != 9264 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { 9265 9266 DP(NETIF_MSG_LINK, "Setting 1G clause37\n"); 9267 bnx2x_cl45_write(bp, phy, 9268 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0); 9269 bnx2x_cl45_write(bp, phy, 9270 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300); 9271 } else { 9272 /* Since the 8727 has only single reset pin, need to set the 10G 9273 * registers although it is default 9274 */ 9275 bnx2x_cl45_write(bp, phy, 9276 MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 9277 0x0020); 9278 bnx2x_cl45_write(bp, phy, 9279 MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100); 9280 bnx2x_cl45_write(bp, phy, 9281 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040); 9282 bnx2x_cl45_write(bp, phy, 9283 MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 9284 0x0008); 9285 } 9286} 9287 9288static int bnx2x_8727_config_init(struct bnx2x_phy *phy, 9289 struct link_params *params, 9290 struct link_vars *vars) 9291{ 9292 u32 tx_en_mode; 9293 u16 tmp1, mod_abs, tmp2; 9294 struct bnx2x *bp = params->bp; 9295 /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */ 9296 9297 bnx2x_wait_reset_complete(bp, phy, params); 9298 9299 DP(NETIF_MSG_LINK, "Initializing BCM8727\n"); 9300 9301 bnx2x_8727_specific_func(phy, params, PHY_INIT); 9302 /* Initially configure MOD_ABS to interrupt when module is 9303 * presence( bit 8) 9304 */ 9305 bnx2x_cl45_read(bp, phy, 9306 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); 9307 /* Set EDC off by setting OPTXLOS signal input to low (bit 9). 9308 * When the EDC is off it locks onto a reference clock and avoids 9309 * becoming 'lost' 9310 */ 9311 mod_abs &= ~(1<<8); 9312 if (!(phy->flags & FLAGS_NOC)) 9313 mod_abs &= ~(1<<9); 9314 bnx2x_cl45_write(bp, phy, 9315 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); 9316 9317 /* Enable/Disable PHY transmitter output */ 9318 bnx2x_set_disable_pmd_transmit(params, phy, 0); 9319 9320 bnx2x_8727_power_module(bp, phy, 1); 9321 9322 bnx2x_cl45_read(bp, phy, 9323 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &tmp1); 9324 9325 bnx2x_cl45_read(bp, phy, 9326 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1); 9327 9328 bnx2x_8727_config_speed(phy, params); 9329 9330 9331 /* Set TX PreEmphasis if needed */ 9332 if ((params->feature_config_flags & 9333 FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) { 9334 DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x, TX_CTRL2 0x%x\n", 9335 phy->tx_preemphasis[0], 9336 phy->tx_preemphasis[1]); 9337 bnx2x_cl45_write(bp, phy, 9338 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL1, 9339 phy->tx_preemphasis[0]); 9340 9341 bnx2x_cl45_write(bp, phy, 9342 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_TX_CTRL2, 9343 phy->tx_preemphasis[1]); 9344 } 9345 9346 /* If TX Laser is controlled by GPIO_0, do not let PHY go into low 9347 * power mode, if TX Laser is disabled 9348 */ 9349 tx_en_mode = REG_RD(bp, params->shmem_base + 9350 offsetof(struct shmem_region, 9351 dev_info.port_hw_config[params->port].sfp_ctrl)) 9352 & PORT_HW_CFG_TX_LASER_MASK; 9353 9354 if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) { 9355 9356 DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n"); 9357 bnx2x_cl45_read(bp, phy, 9358 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, &tmp2); 9359 tmp2 |= 0x1000; 9360 tmp2 &= 0xFFEF; 9361 bnx2x_cl45_write(bp, phy, 9362 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, tmp2); 9363 bnx2x_cl45_read(bp, phy, 9364 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 9365 &tmp2); 9366 bnx2x_cl45_write(bp, phy, 9367 MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, 9368 (tmp2 & 0x7fff)); 9369 } 9370 9371 return 0; 9372} 9373 9374static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, 9375 struct link_params *params) 9376{ 9377 struct bnx2x *bp = params->bp; 9378 u16 mod_abs, rx_alarm_status; 9379 u32 val = REG_RD(bp, params->shmem_base + 9380 offsetof(struct shmem_region, dev_info. 9381 port_feature_config[params->port]. 9382 config)); 9383 bnx2x_cl45_read(bp, phy, 9384 MDIO_PMA_DEVAD, 9385 MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); 9386 if (mod_abs & (1<<8)) { 9387 9388 /* Module is absent */ 9389 DP(NETIF_MSG_LINK, 9390 "MOD_ABS indication show module is absent\n"); 9391 phy->media_type = ETH_PHY_NOT_PRESENT; 9392 /* 1. Set mod_abs to detect next module 9393 * presence event 9394 * 2. Set EDC off by setting OPTXLOS signal input to low 9395 * (bit 9). 9396 * When the EDC is off it locks onto a reference clock and 9397 * avoids becoming 'lost'. 9398 */ 9399 mod_abs &= ~(1<<8); 9400 if (!(phy->flags & FLAGS_NOC)) 9401 mod_abs &= ~(1<<9); 9402 bnx2x_cl45_write(bp, phy, 9403 MDIO_PMA_DEVAD, 9404 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); 9405 9406 /* Clear RX alarm since it stays up as long as 9407 * the mod_abs wasn't changed 9408 */ 9409 bnx2x_cl45_read(bp, phy, 9410 MDIO_PMA_DEVAD, 9411 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status); 9412 9413 } else { 9414 /* Module is present */ 9415 DP(NETIF_MSG_LINK, 9416 "MOD_ABS indication show module is present\n"); 9417 /* First disable transmitter, and if the module is ok, the 9418 * module_detection will enable it 9419 * 1. Set mod_abs to detect next module absent event ( bit 8) 9420 * 2. Restore the default polarity of the OPRXLOS signal and 9421 * this signal will then correctly indicate the presence or 9422 * absence of the Rx signal. (bit 9) 9423 */ 9424 mod_abs |= (1<<8); 9425 if (!(phy->flags & FLAGS_NOC)) 9426 mod_abs |= (1<<9); 9427 bnx2x_cl45_write(bp, phy, 9428 MDIO_PMA_DEVAD, 9429 MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); 9430 9431 /* Clear RX alarm since it stays up as long as the mod_abs 9432 * wasn't changed. This is need to be done before calling the 9433 * module detection, otherwise it will clear* the link update 9434 * alarm 9435 */ 9436 bnx2x_cl45_read(bp, phy, 9437 MDIO_PMA_DEVAD, 9438 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status); 9439 9440 9441 if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == 9442 PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) 9443 bnx2x_sfp_set_transmitter(params, phy, 0); 9444 9445 if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) 9446 bnx2x_sfp_module_detection(phy, params); 9447 else 9448 DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); 9449 9450 /* Reconfigure link speed based on module type limitations */ 9451 bnx2x_8727_config_speed(phy, params); 9452 } 9453 9454 DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", 9455 rx_alarm_status); 9456 /* No need to check link status in case of module plugged in/out */ 9457} 9458 9459static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, 9460 struct link_params *params, 9461 struct link_vars *vars) 9462 9463{ 9464 struct bnx2x *bp = params->bp; 9465 u8 link_up = 0, oc_port = params->port; 9466 u16 link_status = 0; 9467 u16 rx_alarm_status, lasi_ctrl, val1; 9468 9469 /* If PHY is not initialized, do not check link status */ 9470 bnx2x_cl45_read(bp, phy, 9471 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 9472 &lasi_ctrl); 9473 if (!lasi_ctrl) 9474 return 0; 9475 9476 /* Check the LASI on Rx */ 9477 bnx2x_cl45_read(bp, phy, 9478 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, 9479 &rx_alarm_status); 9480 vars->line_speed = 0; 9481 DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", rx_alarm_status); 9482 9483 bnx2x_sfp_mask_fault(bp, phy, MDIO_PMA_LASI_TXSTAT, 9484 MDIO_PMA_LASI_TXCTRL); 9485 9486 bnx2x_cl45_read(bp, phy, 9487 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1); 9488 9489 DP(NETIF_MSG_LINK, "8727 LASI status 0x%x\n", val1); 9490 9491 /* Clear MSG-OUT */ 9492 bnx2x_cl45_read(bp, phy, 9493 MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1); 9494 9495 /* If a module is present and there is need to check 9496 * for over current 9497 */ 9498 if (!(phy->flags & FLAGS_NOC) && !(rx_alarm_status & (1<<5))) { 9499 /* Check over-current using 8727 GPIO0 input*/ 9500 bnx2x_cl45_read(bp, phy, 9501 MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_GPIO_CTRL, 9502 &val1); 9503 9504 if ((val1 & (1<<8)) == 0) { 9505 if (!CHIP_IS_E1x(bp)) 9506 oc_port = BP_PATH(bp) + (params->port << 1); 9507 DP(NETIF_MSG_LINK, 9508 "8727 Power fault has been detected on port %d\n", 9509 oc_port); 9510 netdev_err(bp->dev, "Error: Power fault on Port %d has " 9511 "been detected and the power to " 9512 "that SFP+ module has been removed " 9513 "to prevent failure of the card. " 9514 "Please remove the SFP+ module and " 9515 "restart the system to clear this " 9516 "error.\n", 9517 oc_port); 9518 /* Disable all RX_ALARMs except for mod_abs */ 9519 bnx2x_cl45_write(bp, phy, 9520 MDIO_PMA_DEVAD, 9521 MDIO_PMA_LASI_RXCTRL, (1<<5)); 9522 9523 bnx2x_cl45_read(bp, phy, 9524 MDIO_PMA_DEVAD, 9525 MDIO_PMA_REG_PHY_IDENTIFIER, &val1); 9526 /* Wait for module_absent_event */ 9527 val1 |= (1<<8); 9528 bnx2x_cl45_write(bp, phy, 9529 MDIO_PMA_DEVAD, 9530 MDIO_PMA_REG_PHY_IDENTIFIER, val1); 9531 /* Clear RX alarm */ 9532 bnx2x_cl45_read(bp, phy, 9533 MDIO_PMA_DEVAD, 9534 MDIO_PMA_LASI_RXSTAT, &rx_alarm_status); 9535 bnx2x_8727_power_module(params->bp, phy, 0); 9536 return 0; 9537 } 9538 } /* Over current check */ 9539 9540 /* When module absent bit is set, check module */ 9541 if (rx_alarm_status & (1<<5)) { 9542 bnx2x_8727_handle_mod_abs(phy, params); 9543 /* Enable all mod_abs and link detection bits */ 9544 bnx2x_cl45_write(bp, phy, 9545 MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXCTRL, 9546 ((1<<5) | (1<<2))); 9547 } 9548 9549 if (!(phy->flags & FLAGS_SFP_NOT_APPROVED)) { 9550 DP(NETIF_MSG_LINK, "Enabling 8727 TX laser\n"); 9551 bnx2x_sfp_set_transmitter(params, phy, 1); 9552 } else { 9553 DP(NETIF_MSG_LINK, "Tx is disabled\n"); 9554 return 0; 9555 } 9556 9557 bnx2x_cl45_read(bp, phy, 9558 MDIO_PMA_DEVAD, 9559 MDIO_PMA_REG_8073_SPEED_LINK_STATUS, &link_status); 9560 9561 /* Bits 0..2 --> speed detected, 9562 * Bits 13..15--> link is down 9563 */ 9564 if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) { 9565 link_up = 1; 9566 vars->line_speed = SPEED_10000; 9567 DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n", 9568 params->port); 9569 } else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) { 9570 link_up = 1; 9571 vars->line_speed = SPEED_1000; 9572 DP(NETIF_MSG_LINK, "port %x: External link up in 1G\n", 9573 params->port); 9574 } else { 9575 link_up = 0; 9576 DP(NETIF_MSG_LINK, "port %x: External link is down\n", 9577 params->port); 9578 } 9579 9580 /* Capture 10G link fault. */ 9581 if (vars->line_speed == SPEED_10000) { 9582 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 9583 MDIO_PMA_LASI_TXSTAT, &val1); 9584 9585 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 9586 MDIO_PMA_LASI_TXSTAT, &val1); 9587 9588 if (val1 & (1<<0)) { 9589 vars->fault_detected = 1; 9590 } 9591 } 9592 9593 if (link_up) { 9594 bnx2x_ext_phy_resolve_fc(phy, params, vars); 9595 vars->duplex = DUPLEX_FULL; 9596 DP(NETIF_MSG_LINK, "duplex = 0x%x\n", vars->duplex); 9597 } 9598 9599 if ((DUAL_MEDIA(params)) && 9600 (phy->req_line_speed == SPEED_1000)) { 9601 bnx2x_cl45_read(bp, phy, 9602 MDIO_PMA_DEVAD, 9603 MDIO_PMA_REG_8727_PCS_GP, &val1); 9604 /* In case of dual-media board and 1G, power up the XAUI side, 9605 * otherwise power it down. For 10G it is done automatically 9606 */ 9607 if (link_up) 9608 val1 &= ~(3<<10); 9609 else 9610 val1 |= (3<<10); 9611 bnx2x_cl45_write(bp, phy, 9612 MDIO_PMA_DEVAD, 9613 MDIO_PMA_REG_8727_PCS_GP, val1); 9614 } 9615 return link_up; 9616} 9617 9618static void bnx2x_8727_link_reset(struct bnx2x_phy *phy, 9619 struct link_params *params) 9620{ 9621 struct bnx2x *bp = params->bp; 9622 9623 /* Enable/Disable PHY transmitter output */ 9624 bnx2x_set_disable_pmd_transmit(params, phy, 1); 9625 9626 /* Disable Transmitter */ 9627 bnx2x_sfp_set_transmitter(params, phy, 0); 9628 /* Clear LASI */ 9629 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0); 9630 9631} 9632 9633/******************************************************************/ 9634/* BCM8481/BCM84823/BCM84833 PHY SECTION */ 9635/******************************************************************/ 9636static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy, 9637 struct bnx2x *bp, 9638 u8 port) 9639{ 9640 u16 val, fw_ver2, cnt, i; 9641 static struct bnx2x_reg_set reg_set[] = { 9642 {MDIO_PMA_DEVAD, 0xA819, 0x0014}, 9643 {MDIO_PMA_DEVAD, 0xA81A, 0xc200}, 9644 {MDIO_PMA_DEVAD, 0xA81B, 0x0000}, 9645 {MDIO_PMA_DEVAD, 0xA81C, 0x0300}, 9646 {MDIO_PMA_DEVAD, 0xA817, 0x0009} 9647 }; 9648 u16 fw_ver1; 9649 9650 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 9651 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) { 9652 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 0x400f, &fw_ver1); 9653 bnx2x_save_spirom_version(bp, port, fw_ver1 & 0xfff, 9654 phy->ver_addr); 9655 } else { 9656 /* For 32-bit registers in 848xx, access via MDIO2ARM i/f. */ 9657 /* (1) set reg 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */ 9658 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 9659 bnx2x_cl45_write(bp, phy, reg_set[i].devad, 9660 reg_set[i].reg, reg_set[i].val); 9661 9662 for (cnt = 0; cnt < 100; cnt++) { 9663 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val); 9664 if (val & 1) 9665 break; 9666 udelay(5); 9667 } 9668 if (cnt == 100) { 9669 DP(NETIF_MSG_LINK, "Unable to read 848xx " 9670 "phy fw version(1)\n"); 9671 bnx2x_save_spirom_version(bp, port, 0, 9672 phy->ver_addr); 9673 return; 9674 } 9675 9676 9677 /* 2) read register 0xc200_0000 (SPI_FW_STATUS) */ 9678 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819, 0x0000); 9679 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A, 0xc200); 9680 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817, 0x000A); 9681 for (cnt = 0; cnt < 100; cnt++) { 9682 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val); 9683 if (val & 1) 9684 break; 9685 udelay(5); 9686 } 9687 if (cnt == 100) { 9688 DP(NETIF_MSG_LINK, "Unable to read 848xx phy fw " 9689 "version(2)\n"); 9690 bnx2x_save_spirom_version(bp, port, 0, 9691 phy->ver_addr); 9692 return; 9693 } 9694 9695 /* lower 16 bits of the register SPI_FW_STATUS */ 9696 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81B, &fw_ver1); 9697 /* upper 16 bits of register SPI_FW_STATUS */ 9698 bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81C, &fw_ver2); 9699 9700 bnx2x_save_spirom_version(bp, port, (fw_ver2<<16) | fw_ver1, 9701 phy->ver_addr); 9702 } 9703 9704} 9705static void bnx2x_848xx_set_led(struct bnx2x *bp, 9706 struct bnx2x_phy *phy) 9707{ 9708 u16 val, offset, i; 9709 static struct bnx2x_reg_set reg_set[] = { 9710 {MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_LED1_MASK, 0x0080}, 9711 {MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_LED2_MASK, 0x0018}, 9712 {MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_LED3_MASK, 0x0006}, 9713 {MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_LED3_BLINK, 0x0000}, 9714 {MDIO_PMA_DEVAD, MDIO_PMA_REG_84823_CTL_SLOW_CLK_CNT_HIGH, 9715 MDIO_PMA_REG_84823_BLINK_RATE_VAL_15P9HZ}, 9716 {MDIO_AN_DEVAD, 0xFFFB, 0xFFFD} 9717 }; 9718 /* PHYC_CTL_LED_CTL */ 9719 bnx2x_cl45_read(bp, phy, 9720 MDIO_PMA_DEVAD, 9721 MDIO_PMA_REG_8481_LINK_SIGNAL, &val); 9722 val &= 0xFE00; 9723 val |= 0x0092; 9724 9725 bnx2x_cl45_write(bp, phy, 9726 MDIO_PMA_DEVAD, 9727 MDIO_PMA_REG_8481_LINK_SIGNAL, val); 9728 9729 for (i = 0; i < ARRAY_SIZE(reg_set); i++) 9730 bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, 9731 reg_set[i].val); 9732 9733 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 9734 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) 9735 offset = MDIO_PMA_REG_84833_CTL_LED_CTL_1; 9736 else 9737 offset = MDIO_PMA_REG_84823_CTL_LED_CTL_1; 9738 9739 /* stretch_en for LED3*/ 9740 bnx2x_cl45_read_or_write(bp, phy, 9741 MDIO_PMA_DEVAD, offset, 9742 MDIO_PMA_REG_84823_LED3_STRETCH_EN); 9743} 9744 9745static void bnx2x_848xx_specific_func(struct bnx2x_phy *phy, 9746 struct link_params *params, 9747 u32 action) 9748{ 9749 struct bnx2x *bp = params->bp; 9750 switch (action) { 9751 case PHY_INIT: 9752 if ((phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) && 9753 (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) { 9754 /* Save spirom version */ 9755 bnx2x_save_848xx_spirom_version(phy, bp, params->port); 9756 } 9757 /* This phy uses the NIG latch mechanism since link indication 9758 * arrives through its LED4 and not via its LASI signal, so we 9759 * get steady signal instead of clear on read 9760 */ 9761 bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4, 9762 1 << NIG_LATCH_BC_ENABLE_MI_INT); 9763 9764 bnx2x_848xx_set_led(bp, phy); 9765 break; 9766 } 9767} 9768 9769static int bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy, 9770 struct link_params *params, 9771 struct link_vars *vars) 9772{ 9773 struct bnx2x *bp = params->bp; 9774 u16 autoneg_val, an_1000_val, an_10_100_val; 9775 9776 bnx2x_848xx_specific_func(phy, params, PHY_INIT); 9777 bnx2x_cl45_write(bp, phy, 9778 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x0000); 9779 9780 /* set 1000 speed advertisement */ 9781 bnx2x_cl45_read(bp, phy, 9782 MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL, 9783 &an_1000_val); 9784 9785 bnx2x_ext_phy_set_pause(params, phy, vars); 9786 bnx2x_cl45_read(bp, phy, 9787 MDIO_AN_DEVAD, 9788 MDIO_AN_REG_8481_LEGACY_AN_ADV, 9789 &an_10_100_val); 9790 bnx2x_cl45_read(bp, phy, 9791 MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_MII_CTRL, 9792 &autoneg_val); 9793 /* Disable forced speed */ 9794 autoneg_val &= ~((1<<6) | (1<<8) | (1<<9) | (1<<12) | (1<<13)); 9795 an_10_100_val &= ~((1<<5) | (1<<6) | (1<<7) | (1<<8)); 9796 9797 if (((phy->req_line_speed == SPEED_AUTO_NEG) && 9798 (phy->speed_cap_mask & 9799 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || 9800 (phy->req_line_speed == SPEED_1000)) { 9801 an_1000_val |= (1<<8); 9802 autoneg_val |= (1<<9 | 1<<12); 9803 if (phy->req_duplex == DUPLEX_FULL) 9804 an_1000_val |= (1<<9); 9805 DP(NETIF_MSG_LINK, "Advertising 1G\n"); 9806 } else 9807 an_1000_val &= ~((1<<8) | (1<<9)); 9808 9809 bnx2x_cl45_write(bp, phy, 9810 MDIO_AN_DEVAD, MDIO_AN_REG_8481_1000T_CTRL, 9811 an_1000_val); 9812 9813 /* Set 10/100 speed advertisement */ 9814 if (phy->req_line_speed == SPEED_AUTO_NEG) { 9815 if (phy->speed_cap_mask & 9816 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL) { 9817 /* Enable autoneg and restart autoneg for legacy speeds 9818 */ 9819 autoneg_val |= (1<<9 | 1<<12); 9820 an_10_100_val |= (1<<8); 9821 DP(NETIF_MSG_LINK, "Advertising 100M-FD\n"); 9822 } 9823 9824 if (phy->speed_cap_mask & 9825 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF) { 9826 /* Enable autoneg and restart autoneg for legacy speeds 9827 */ 9828 autoneg_val |= (1<<9 | 1<<12); 9829 an_10_100_val |= (1<<7); 9830 DP(NETIF_MSG_LINK, "Advertising 100M-HD\n"); 9831 } 9832 9833 if ((phy->speed_cap_mask & 9834 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) && 9835 (phy->supported & SUPPORTED_10baseT_Full)) { 9836 an_10_100_val |= (1<<6); 9837 autoneg_val |= (1<<9 | 1<<12); 9838 DP(NETIF_MSG_LINK, "Advertising 10M-FD\n"); 9839 } 9840 9841 if ((phy->speed_cap_mask & 9842 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF) && 9843 (phy->supported & SUPPORTED_10baseT_Half)) { 9844 an_10_100_val |= (1<<5); 9845 autoneg_val |= (1<<9 | 1<<12); 9846 DP(NETIF_MSG_LINK, "Advertising 10M-HD\n"); 9847 } 9848 } 9849 9850 /* Only 10/100 are allowed to work in FORCE mode */ 9851 if ((phy->req_line_speed == SPEED_100) && 9852 (phy->supported & 9853 (SUPPORTED_100baseT_Half | 9854 SUPPORTED_100baseT_Full))) { 9855 autoneg_val |= (1<<13); 9856 /* Enabled AUTO-MDIX when autoneg is disabled */ 9857 bnx2x_cl45_write(bp, phy, 9858 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL, 9859 (1<<15 | 1<<9 | 7<<0)); 9860 /* The PHY needs this set even for forced link. */ 9861 an_10_100_val |= (1<<8) | (1<<7); 9862 DP(NETIF_MSG_LINK, "Setting 100M force\n"); 9863 } 9864 if ((phy->req_line_speed == SPEED_10) && 9865 (phy->supported & 9866 (SUPPORTED_10baseT_Half | 9867 SUPPORTED_10baseT_Full))) { 9868 /* Enabled AUTO-MDIX when autoneg is disabled */ 9869 bnx2x_cl45_write(bp, phy, 9870 MDIO_AN_DEVAD, MDIO_AN_REG_8481_AUX_CTRL, 9871 (1<<15 | 1<<9 | 7<<0)); 9872 DP(NETIF_MSG_LINK, "Setting 10M force\n"); 9873 } 9874 9875 bnx2x_cl45_write(bp, phy, 9876 MDIO_AN_DEVAD, MDIO_AN_REG_8481_LEGACY_AN_ADV, 9877 an_10_100_val); 9878 9879 if (phy->req_duplex == DUPLEX_FULL) 9880 autoneg_val |= (1<<8); 9881 9882 /* Always write this if this is not 84833/4. 9883 * For 84833/4, write it only when it's a forced speed. 9884 */ 9885 if (((phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) && 9886 (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) || 9887 ((autoneg_val & (1<<12)) == 0)) 9888 bnx2x_cl45_write(bp, phy, 9889 MDIO_AN_DEVAD, 9890 MDIO_AN_REG_8481_LEGACY_MII_CTRL, autoneg_val); 9891 9892 if (((phy->req_line_speed == SPEED_AUTO_NEG) && 9893 (phy->speed_cap_mask & 9894 PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) || 9895 (phy->req_line_speed == SPEED_10000)) { 9896 DP(NETIF_MSG_LINK, "Advertising 10G\n"); 9897 /* Restart autoneg for 10G*/ 9898 9899 bnx2x_cl45_read_or_write( 9900 bp, phy, 9901 MDIO_AN_DEVAD, 9902 MDIO_AN_REG_8481_10GBASE_T_AN_CTRL, 9903 0x1000); 9904 bnx2x_cl45_write(bp, phy, 9905 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 9906 0x3200); 9907 } else 9908 bnx2x_cl45_write(bp, phy, 9909 MDIO_AN_DEVAD, 9910 MDIO_AN_REG_8481_10GBASE_T_AN_CTRL, 9911 1); 9912 9913 return 0; 9914} 9915 9916static int bnx2x_8481_config_init(struct bnx2x_phy *phy, 9917 struct link_params *params, 9918 struct link_vars *vars) 9919{ 9920 struct bnx2x *bp = params->bp; 9921 /* Restore normal power mode*/ 9922 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 9923 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); 9924 9925 /* HW reset */ 9926 bnx2x_ext_phy_hw_reset(bp, params->port); 9927 bnx2x_wait_reset_complete(bp, phy, params); 9928 9929 bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); 9930 return bnx2x_848xx_cmn_config_init(phy, params, vars); 9931} 9932 9933#define PHY84833_CMDHDLR_WAIT 300 9934#define PHY84833_CMDHDLR_MAX_ARGS 5 9935static int bnx2x_84833_cmd_hdlr(struct bnx2x_phy *phy, 9936 struct link_params *params, u16 fw_cmd, 9937 u16 cmd_args[], int argc) 9938{ 9939 int idx; 9940 u16 val; 9941 struct bnx2x *bp = params->bp; 9942 /* Write CMD_OPEN_OVERRIDE to STATUS reg */ 9943 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 9944 MDIO_84833_CMD_HDLR_STATUS, 9945 PHY84833_STATUS_CMD_OPEN_OVERRIDE); 9946 for (idx = 0; idx < PHY84833_CMDHDLR_WAIT; idx++) { 9947 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 9948 MDIO_84833_CMD_HDLR_STATUS, &val); 9949 if (val == PHY84833_STATUS_CMD_OPEN_FOR_CMDS) 9950 break; 9951 usleep_range(1000, 2000); 9952 } 9953 if (idx >= PHY84833_CMDHDLR_WAIT) { 9954 DP(NETIF_MSG_LINK, "FW cmd: FW not ready.\n"); 9955 return -EINVAL; 9956 } 9957 9958 /* Prepare argument(s) and issue command */ 9959 for (idx = 0; idx < argc; idx++) { 9960 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 9961 MDIO_84833_CMD_HDLR_DATA1 + idx, 9962 cmd_args[idx]); 9963 } 9964 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 9965 MDIO_84833_CMD_HDLR_COMMAND, fw_cmd); 9966 for (idx = 0; idx < PHY84833_CMDHDLR_WAIT; idx++) { 9967 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 9968 MDIO_84833_CMD_HDLR_STATUS, &val); 9969 if ((val == PHY84833_STATUS_CMD_COMPLETE_PASS) || 9970 (val == PHY84833_STATUS_CMD_COMPLETE_ERROR)) 9971 break; 9972 usleep_range(1000, 2000); 9973 } 9974 if ((idx >= PHY84833_CMDHDLR_WAIT) || 9975 (val == PHY84833_STATUS_CMD_COMPLETE_ERROR)) { 9976 DP(NETIF_MSG_LINK, "FW cmd failed.\n"); 9977 return -EINVAL; 9978 } 9979 /* Gather returning data */ 9980 for (idx = 0; idx < argc; idx++) { 9981 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 9982 MDIO_84833_CMD_HDLR_DATA1 + idx, 9983 &cmd_args[idx]); 9984 } 9985 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 9986 MDIO_84833_CMD_HDLR_STATUS, 9987 PHY84833_STATUS_CMD_CLEAR_COMPLETE); 9988 return 0; 9989} 9990 9991static int bnx2x_84833_pair_swap_cfg(struct bnx2x_phy *phy, 9992 struct link_params *params, 9993 struct link_vars *vars) 9994{ 9995 u32 pair_swap; 9996 u16 data[PHY84833_CMDHDLR_MAX_ARGS]; 9997 int status; 9998 struct bnx2x *bp = params->bp; 9999 10000 /* Check for configuration. */ 10001 pair_swap = REG_RD(bp, params->shmem_base + 10002 offsetof(struct shmem_region, 10003 dev_info.port_hw_config[params->port].xgbt_phy_cfg)) & 10004 PORT_HW_CFG_RJ45_PAIR_SWAP_MASK; 10005 10006 if (pair_swap == 0) 10007 return 0; 10008 10009 /* Only the second argument is used for this command */ 10010 data[1] = (u16)pair_swap; 10011 10012 status = bnx2x_84833_cmd_hdlr(phy, params, 10013 PHY84833_CMD_SET_PAIR_SWAP, data, PHY84833_CMDHDLR_MAX_ARGS); 10014 if (status == 0) 10015 DP(NETIF_MSG_LINK, "Pairswap OK, val=0x%x\n", data[1]); 10016 10017 return status; 10018} 10019 10020static u8 bnx2x_84833_get_reset_gpios(struct bnx2x *bp, 10021 u32 shmem_base_path[], 10022 u32 chip_id) 10023{ 10024 u32 reset_pin[2]; 10025 u32 idx; 10026 u8 reset_gpios; 10027 if (CHIP_IS_E3(bp)) { 10028 /* Assume that these will be GPIOs, not EPIOs. */ 10029 for (idx = 0; idx < 2; idx++) { 10030 /* Map config param to register bit. */ 10031 reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] + 10032 offsetof(struct shmem_region, 10033 dev_info.port_hw_config[0].e3_cmn_pin_cfg)); 10034 reset_pin[idx] = (reset_pin[idx] & 10035 PORT_HW_CFG_E3_PHY_RESET_MASK) >> 10036 PORT_HW_CFG_E3_PHY_RESET_SHIFT; 10037 reset_pin[idx] -= PIN_CFG_GPIO0_P0; 10038 reset_pin[idx] = (1 << reset_pin[idx]); 10039 } 10040 reset_gpios = (u8)(reset_pin[0] | reset_pin[1]); 10041 } else { 10042 /* E2, look from diff place of shmem. */ 10043 for (idx = 0; idx < 2; idx++) { 10044 reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] + 10045 offsetof(struct shmem_region, 10046 dev_info.port_hw_config[0].default_cfg)); 10047 reset_pin[idx] &= PORT_HW_CFG_EXT_PHY_GPIO_RST_MASK; 10048 reset_pin[idx] -= PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0; 10049 reset_pin[idx] >>= PORT_HW_CFG_EXT_PHY_GPIO_RST_SHIFT; 10050 reset_pin[idx] = (1 << reset_pin[idx]); 10051 } 10052 reset_gpios = (u8)(reset_pin[0] | reset_pin[1]); 10053 } 10054 10055 return reset_gpios; 10056} 10057 10058static int bnx2x_84833_hw_reset_phy(struct bnx2x_phy *phy, 10059 struct link_params *params) 10060{ 10061 struct bnx2x *bp = params->bp; 10062 u8 reset_gpios; 10063 u32 other_shmem_base_addr = REG_RD(bp, params->shmem2_base + 10064 offsetof(struct shmem2_region, 10065 other_shmem_base_addr)); 10066 10067 u32 shmem_base_path[2]; 10068 10069 /* Work around for 84833 LED failure inside RESET status */ 10070 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 10071 MDIO_AN_REG_8481_LEGACY_MII_CTRL, 10072 MDIO_AN_REG_8481_MII_CTRL_FORCE_1G); 10073 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 10074 MDIO_AN_REG_8481_1G_100T_EXT_CTRL, 10075 MIDO_AN_REG_8481_EXT_CTRL_FORCE_LEDS_OFF); 10076 10077 shmem_base_path[0] = params->shmem_base; 10078 shmem_base_path[1] = other_shmem_base_addr; 10079 10080 reset_gpios = bnx2x_84833_get_reset_gpios(bp, shmem_base_path, 10081 params->chip_id); 10082 10083 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_LOW); 10084 udelay(10); 10085 DP(NETIF_MSG_LINK, "84833 hw reset on pin values 0x%x\n", 10086 reset_gpios); 10087 10088 return 0; 10089} 10090 10091static int bnx2x_8483x_disable_eee(struct bnx2x_phy *phy, 10092 struct link_params *params, 10093 struct link_vars *vars) 10094{ 10095 int rc; 10096 struct bnx2x *bp = params->bp; 10097 u16 cmd_args = 0; 10098 10099 DP(NETIF_MSG_LINK, "Don't Advertise 10GBase-T EEE\n"); 10100 10101 /* Prevent Phy from working in EEE and advertising it */ 10102 rc = bnx2x_84833_cmd_hdlr(phy, params, 10103 PHY84833_CMD_SET_EEE_MODE, &cmd_args, 1); 10104 if (rc) { 10105 DP(NETIF_MSG_LINK, "EEE disable failed.\n"); 10106 return rc; 10107 } 10108 10109 return bnx2x_eee_disable(phy, params, vars); 10110} 10111 10112static int bnx2x_8483x_enable_eee(struct bnx2x_phy *phy, 10113 struct link_params *params, 10114 struct link_vars *vars) 10115{ 10116 int rc; 10117 struct bnx2x *bp = params->bp; 10118 u16 cmd_args = 1; 10119 10120 rc = bnx2x_84833_cmd_hdlr(phy, params, 10121 PHY84833_CMD_SET_EEE_MODE, &cmd_args, 1); 10122 if (rc) { 10123 DP(NETIF_MSG_LINK, "EEE enable failed.\n"); 10124 return rc; 10125 } 10126 10127 return bnx2x_eee_advertise(phy, params, vars, SHMEM_EEE_10G_ADV); 10128} 10129 10130#define PHY84833_CONSTANT_LATENCY 1193 10131static int bnx2x_848x3_config_init(struct bnx2x_phy *phy, 10132 struct link_params *params, 10133 struct link_vars *vars) 10134{ 10135 struct bnx2x *bp = params->bp; 10136 u8 port, initialize = 1; 10137 u16 val; 10138 u32 actual_phy_selection; 10139 u16 cmd_args[PHY84833_CMDHDLR_MAX_ARGS]; 10140 int rc = 0; 10141 10142 usleep_range(1000, 2000); 10143 10144 if (!(CHIP_IS_E1x(bp))) 10145 port = BP_PATH(bp); 10146 else 10147 port = params->port; 10148 10149 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) { 10150 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, 10151 MISC_REGISTERS_GPIO_OUTPUT_HIGH, 10152 port); 10153 } else { 10154 /* MDIO reset */ 10155 bnx2x_cl45_write(bp, phy, 10156 MDIO_PMA_DEVAD, 10157 MDIO_PMA_REG_CTRL, 0x8000); 10158 } 10159 10160 bnx2x_wait_reset_complete(bp, phy, params); 10161 10162 /* Wait for GPHY to come out of reset */ 10163 msleep(50); 10164 if ((phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) && 10165 (phy->type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) { 10166 /* BCM84823 requires that XGXS links up first @ 10G for normal 10167 * behavior. 10168 */ 10169 u16 temp; 10170 temp = vars->line_speed; 10171 vars->line_speed = SPEED_10000; 10172 bnx2x_set_autoneg(¶ms->phy[INT_PHY], params, vars, 0); 10173 bnx2x_program_serdes(¶ms->phy[INT_PHY], params, vars); 10174 vars->line_speed = temp; 10175 } 10176 10177 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 10178 MDIO_CTL_REG_84823_MEDIA, &val); 10179 val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK | 10180 MDIO_CTL_REG_84823_MEDIA_LINE_MASK | 10181 MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN | 10182 MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK | 10183 MDIO_CTL_REG_84823_MEDIA_FIBER_1G); 10184 10185 if (CHIP_IS_E3(bp)) { 10186 val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK | 10187 MDIO_CTL_REG_84823_MEDIA_LINE_MASK); 10188 } else { 10189 val |= (MDIO_CTL_REG_84823_CTRL_MAC_XFI | 10190 MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L); 10191 } 10192 10193 actual_phy_selection = bnx2x_phy_selection(params); 10194 10195 switch (actual_phy_selection) { 10196 case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT: 10197 /* Do nothing. Essentially this is like the priority copper */ 10198 break; 10199 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY: 10200 val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_COPPER; 10201 break; 10202 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY: 10203 val |= MDIO_CTL_REG_84823_MEDIA_PRIORITY_FIBER; 10204 break; 10205 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY: 10206 /* Do nothing here. The first PHY won't be initialized at all */ 10207 break; 10208 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY: 10209 val |= MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN; 10210 initialize = 0; 10211 break; 10212 } 10213 if (params->phy[EXT_PHY2].req_line_speed == SPEED_1000) 10214 val |= MDIO_CTL_REG_84823_MEDIA_FIBER_1G; 10215 10216 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 10217 MDIO_CTL_REG_84823_MEDIA, val); 10218 DP(NETIF_MSG_LINK, "Multi_phy config = 0x%x, Media control = 0x%x\n", 10219 params->multi_phy_config, val); 10220 10221 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 10222 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) { 10223 bnx2x_84833_pair_swap_cfg(phy, params, vars); 10224 10225 /* Keep AutogrEEEn disabled. */ 10226 cmd_args[0] = 0x0; 10227 cmd_args[1] = 0x0; 10228 cmd_args[2] = PHY84833_CONSTANT_LATENCY + 1; 10229 cmd_args[3] = PHY84833_CONSTANT_LATENCY; 10230 rc = bnx2x_84833_cmd_hdlr(phy, params, 10231 PHY84833_CMD_SET_EEE_MODE, cmd_args, 10232 PHY84833_CMDHDLR_MAX_ARGS); 10233 if (rc) 10234 DP(NETIF_MSG_LINK, "Cfg AutogrEEEn failed.\n"); 10235 } 10236 if (initialize) 10237 rc = bnx2x_848xx_cmn_config_init(phy, params, vars); 10238 else 10239 bnx2x_save_848xx_spirom_version(phy, bp, params->port); 10240 /* 84833 PHY has a better feature and doesn't need to support this. */ 10241 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) { 10242 u32 cms_enable = REG_RD(bp, params->shmem_base + 10243 offsetof(struct shmem_region, 10244 dev_info.port_hw_config[params->port].default_cfg)) & 10245 PORT_HW_CFG_ENABLE_CMS_MASK; 10246 10247 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 10248 MDIO_CTL_REG_84823_USER_CTRL_REG, &val); 10249 if (cms_enable) 10250 val |= MDIO_CTL_REG_84823_USER_CTRL_CMS; 10251 else 10252 val &= ~MDIO_CTL_REG_84823_USER_CTRL_CMS; 10253 bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, 10254 MDIO_CTL_REG_84823_USER_CTRL_REG, val); 10255 } 10256 10257 bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, 10258 MDIO_84833_TOP_CFG_FW_REV, &val); 10259 10260 /* Configure EEE support */ 10261 if ((val >= MDIO_84833_TOP_CFG_FW_EEE) && 10262 (val != MDIO_84833_TOP_CFG_FW_NO_EEE) && 10263 bnx2x_eee_has_cap(params)) { 10264 rc = bnx2x_eee_initial_config(params, vars, SHMEM_EEE_10G_ADV); 10265 if (rc) { 10266 DP(NETIF_MSG_LINK, "Failed to configure EEE timers\n"); 10267 bnx2x_8483x_disable_eee(phy, params, vars); 10268 return rc; 10269 } 10270 10271 if ((phy->req_duplex == DUPLEX_FULL) && 10272 (params->eee_mode & EEE_MODE_ADV_LPI) && 10273 (bnx2x_eee_calc_timer(params) || 10274 !(params->eee_mode & EEE_MODE_ENABLE_LPI))) 10275 rc = bnx2x_8483x_enable_eee(phy, params, vars); 10276 else 10277 rc = bnx2x_8483x_disable_eee(phy, params, vars); 10278 if (rc) { 10279 DP(NETIF_MSG_LINK, "Failed to set EEE advertisement\n"); 10280 return rc; 10281 } 10282 } else { 10283 vars->eee_status &= ~SHMEM_EEE_SUPPORTED_MASK; 10284 } 10285 10286 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 10287 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) { 10288 /* Bring PHY out of super isolate mode as the final step. */ 10289 bnx2x_cl45_read_and_write(bp, phy, 10290 MDIO_CTL_DEVAD, 10291 MDIO_84833_TOP_CFG_XGPHY_STRAP1, 10292 (u16)~MDIO_84833_SUPER_ISOLATE); 10293 } 10294 return rc; 10295} 10296 10297static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy, 10298 struct link_params *params, 10299 struct link_vars *vars) 10300{ 10301 struct bnx2x *bp = params->bp; 10302 u16 val, val1, val2; 10303 u8 link_up = 0; 10304 10305 10306 /* Check 10G-BaseT link status */ 10307 /* Check PMD signal ok */ 10308 bnx2x_cl45_read(bp, phy, 10309 MDIO_AN_DEVAD, 0xFFFA, &val1); 10310 bnx2x_cl45_read(bp, phy, 10311 MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_PMD_SIGNAL, 10312 &val2); 10313 DP(NETIF_MSG_LINK, "BCM848xx: PMD_SIGNAL 1.a811 = 0x%x\n", val2); 10314 10315 /* Check link 10G */ 10316 if (val2 & (1<<11)) { 10317 vars->line_speed = SPEED_10000; 10318 vars->duplex = DUPLEX_FULL; 10319 link_up = 1; 10320 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars); 10321 } else { /* Check Legacy speed link */ 10322 u16 legacy_status, legacy_speed; 10323 10324 /* Enable expansion register 0x42 (Operation mode status) */ 10325 bnx2x_cl45_write(bp, phy, 10326 MDIO_AN_DEVAD, 10327 MDIO_AN_REG_8481_EXPANSION_REG_ACCESS, 0xf42); 10328 10329 /* Get legacy speed operation status */ 10330 bnx2x_cl45_read(bp, phy, 10331 MDIO_AN_DEVAD, 10332 MDIO_AN_REG_8481_EXPANSION_REG_RD_RW, 10333 &legacy_status); 10334 10335 DP(NETIF_MSG_LINK, "Legacy speed status = 0x%x\n", 10336 legacy_status); 10337 link_up = ((legacy_status & (1<<11)) == (1<<11)); 10338 legacy_speed = (legacy_status & (3<<9)); 10339 if (legacy_speed == (0<<9)) 10340 vars->line_speed = SPEED_10; 10341 else if (legacy_speed == (1<<9)) 10342 vars->line_speed = SPEED_100; 10343 else if (legacy_speed == (2<<9)) 10344 vars->line_speed = SPEED_1000; 10345 else { /* Should not happen: Treat as link down */ 10346 vars->line_speed = 0; 10347 link_up = 0; 10348 } 10349 10350 if (link_up) { 10351 if (legacy_status & (1<<8)) 10352 vars->duplex = DUPLEX_FULL; 10353 else 10354 vars->duplex = DUPLEX_HALF; 10355 10356 DP(NETIF_MSG_LINK, 10357 "Link is up in %dMbps, is_duplex_full= %d\n", 10358 vars->line_speed, 10359 (vars->duplex == DUPLEX_FULL)); 10360 /* Check legacy speed AN resolution */ 10361 bnx2x_cl45_read(bp, phy, 10362 MDIO_AN_DEVAD, 10363 MDIO_AN_REG_8481_LEGACY_MII_STATUS, 10364 &val); 10365 if (val & (1<<5)) 10366 vars->link_status |= 10367 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; 10368 bnx2x_cl45_read(bp, phy, 10369 MDIO_AN_DEVAD, 10370 MDIO_AN_REG_8481_LEGACY_AN_EXPANSION, 10371 &val); 10372 if ((val & (1<<0)) == 0) 10373 vars->link_status |= 10374 LINK_STATUS_PARALLEL_DETECTION_USED; 10375 } 10376 } 10377 if (link_up) { 10378 DP(NETIF_MSG_LINK, "BCM848x3: link speed is %d\n", 10379 vars->line_speed); 10380 bnx2x_ext_phy_resolve_fc(phy, params, vars); 10381 10382 /* Read LP advertised speeds */ 10383 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 10384 MDIO_AN_REG_CL37_FC_LP, &val); 10385 if (val & (1<<5)) 10386 vars->link_status |= 10387 LINK_STATUS_LINK_PARTNER_10THD_CAPABLE; 10388 if (val & (1<<6)) 10389 vars->link_status |= 10390 LINK_STATUS_LINK_PARTNER_10TFD_CAPABLE; 10391 if (val & (1<<7)) 10392 vars->link_status |= 10393 LINK_STATUS_LINK_PARTNER_100TXHD_CAPABLE; 10394 if (val & (1<<8)) 10395 vars->link_status |= 10396 LINK_STATUS_LINK_PARTNER_100TXFD_CAPABLE; 10397 if (val & (1<<9)) 10398 vars->link_status |= 10399 LINK_STATUS_LINK_PARTNER_100T4_CAPABLE; 10400 10401 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 10402 MDIO_AN_REG_1000T_STATUS, &val); 10403 10404 if (val & (1<<10)) 10405 vars->link_status |= 10406 LINK_STATUS_LINK_PARTNER_1000THD_CAPABLE; 10407 if (val & (1<<11)) 10408 vars->link_status |= 10409 LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE; 10410 10411 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 10412 MDIO_AN_REG_MASTER_STATUS, &val); 10413 10414 if (val & (1<<11)) 10415 vars->link_status |= 10416 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 10417 10418 /* Determine if EEE was negotiated */ 10419 if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 10420 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) 10421 bnx2x_eee_an_resolve(phy, params, vars); 10422 } 10423 10424 return link_up; 10425} 10426 10427static int bnx2x_848xx_format_ver(u32 raw_ver, u8 *str, u16 *len) 10428{ 10429 int status = 0; 10430 u32 spirom_ver; 10431 spirom_ver = ((raw_ver & 0xF80) >> 7) << 16 | (raw_ver & 0x7F); 10432 status = bnx2x_format_ver(spirom_ver, str, len); 10433 return status; 10434} 10435 10436static void bnx2x_8481_hw_reset(struct bnx2x_phy *phy, 10437 struct link_params *params) 10438{ 10439 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, 10440 MISC_REGISTERS_GPIO_OUTPUT_LOW, 0); 10441 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, 10442 MISC_REGISTERS_GPIO_OUTPUT_LOW, 1); 10443} 10444 10445static void bnx2x_8481_link_reset(struct bnx2x_phy *phy, 10446 struct link_params *params) 10447{ 10448 bnx2x_cl45_write(params->bp, phy, 10449 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x0000); 10450 bnx2x_cl45_write(params->bp, phy, 10451 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1); 10452} 10453 10454static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy, 10455 struct link_params *params) 10456{ 10457 struct bnx2x *bp = params->bp; 10458 u8 port; 10459 u16 val16; 10460 10461 if (!(CHIP_IS_E1x(bp))) 10462 port = BP_PATH(bp); 10463 else 10464 port = params->port; 10465 10466 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823) { 10467 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, 10468 MISC_REGISTERS_GPIO_OUTPUT_LOW, 10469 port); 10470 } else { 10471 bnx2x_cl45_read(bp, phy, 10472 MDIO_CTL_DEVAD, 10473 MDIO_84833_TOP_CFG_XGPHY_STRAP1, &val16); 10474 val16 |= MDIO_84833_SUPER_ISOLATE; 10475 bnx2x_cl45_write(bp, phy, 10476 MDIO_CTL_DEVAD, 10477 MDIO_84833_TOP_CFG_XGPHY_STRAP1, val16); 10478 } 10479} 10480 10481static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, 10482 struct link_params *params, u8 mode) 10483{ 10484 struct bnx2x *bp = params->bp; 10485 u16 val; 10486 u8 port; 10487 10488 if (!(CHIP_IS_E1x(bp))) 10489 port = BP_PATH(bp); 10490 else 10491 port = params->port; 10492 10493 switch (mode) { 10494 case LED_MODE_OFF: 10495 10496 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OFF\n", port); 10497 10498 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) == 10499 SHARED_HW_CFG_LED_EXTPHY1) { 10500 10501 /* Set LED masks */ 10502 bnx2x_cl45_write(bp, phy, 10503 MDIO_PMA_DEVAD, 10504 MDIO_PMA_REG_8481_LED1_MASK, 10505 0x0); 10506 10507 bnx2x_cl45_write(bp, phy, 10508 MDIO_PMA_DEVAD, 10509 MDIO_PMA_REG_8481_LED2_MASK, 10510 0x0); 10511 10512 bnx2x_cl45_write(bp, phy, 10513 MDIO_PMA_DEVAD, 10514 MDIO_PMA_REG_8481_LED3_MASK, 10515 0x0); 10516 10517 bnx2x_cl45_write(bp, phy, 10518 MDIO_PMA_DEVAD, 10519 MDIO_PMA_REG_8481_LED5_MASK, 10520 0x0); 10521 10522 } else { 10523 bnx2x_cl45_write(bp, phy, 10524 MDIO_PMA_DEVAD, 10525 MDIO_PMA_REG_8481_LED1_MASK, 10526 0x0); 10527 } 10528 break; 10529 case LED_MODE_FRONT_PANEL_OFF: 10530 10531 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE FRONT PANEL OFF\n", 10532 port); 10533 10534 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) == 10535 SHARED_HW_CFG_LED_EXTPHY1) { 10536 10537 /* Set LED masks */ 10538 bnx2x_cl45_write(bp, phy, 10539 MDIO_PMA_DEVAD, 10540 MDIO_PMA_REG_8481_LED1_MASK, 10541 0x0); 10542 10543 bnx2x_cl45_write(bp, phy, 10544 MDIO_PMA_DEVAD, 10545 MDIO_PMA_REG_8481_LED2_MASK, 10546 0x0); 10547 10548 bnx2x_cl45_write(bp, phy, 10549 MDIO_PMA_DEVAD, 10550 MDIO_PMA_REG_8481_LED3_MASK, 10551 0x0); 10552 10553 bnx2x_cl45_write(bp, phy, 10554 MDIO_PMA_DEVAD, 10555 MDIO_PMA_REG_8481_LED5_MASK, 10556 0x20); 10557 10558 } else { 10559 bnx2x_cl45_write(bp, phy, 10560 MDIO_PMA_DEVAD, 10561 MDIO_PMA_REG_8481_LED1_MASK, 10562 0x0); 10563 if (phy->type == 10564 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834) { 10565 /* Disable MI_INT interrupt before setting LED4 10566 * source to constant off. 10567 */ 10568 if (REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + 10569 params->port*4) & 10570 NIG_MASK_MI_INT) { 10571 params->link_flags |= 10572 LINK_FLAGS_INT_DISABLED; 10573 10574 bnx2x_bits_dis( 10575 bp, 10576 NIG_REG_MASK_INTERRUPT_PORT0 + 10577 params->port*4, 10578 NIG_MASK_MI_INT); 10579 } 10580 bnx2x_cl45_write(bp, phy, 10581 MDIO_PMA_DEVAD, 10582 MDIO_PMA_REG_8481_SIGNAL_MASK, 10583 0x0); 10584 } 10585 } 10586 break; 10587 case LED_MODE_ON: 10588 10589 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE ON\n", port); 10590 10591 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) == 10592 SHARED_HW_CFG_LED_EXTPHY1) { 10593 /* Set control reg */ 10594 bnx2x_cl45_read(bp, phy, 10595 MDIO_PMA_DEVAD, 10596 MDIO_PMA_REG_8481_LINK_SIGNAL, 10597 &val); 10598 val &= 0x8000; 10599 val |= 0x2492; 10600 10601 bnx2x_cl45_write(bp, phy, 10602 MDIO_PMA_DEVAD, 10603 MDIO_PMA_REG_8481_LINK_SIGNAL, 10604 val); 10605 10606 /* Set LED masks */ 10607 bnx2x_cl45_write(bp, phy, 10608 MDIO_PMA_DEVAD, 10609 MDIO_PMA_REG_8481_LED1_MASK, 10610 0x0); 10611 10612 bnx2x_cl45_write(bp, phy, 10613 MDIO_PMA_DEVAD, 10614 MDIO_PMA_REG_8481_LED2_MASK, 10615 0x20); 10616 10617 bnx2x_cl45_write(bp, phy, 10618 MDIO_PMA_DEVAD, 10619 MDIO_PMA_REG_8481_LED3_MASK, 10620 0x20); 10621 10622 bnx2x_cl45_write(bp, phy, 10623 MDIO_PMA_DEVAD, 10624 MDIO_PMA_REG_8481_LED5_MASK, 10625 0x0); 10626 } else { 10627 bnx2x_cl45_write(bp, phy, 10628 MDIO_PMA_DEVAD, 10629 MDIO_PMA_REG_8481_LED1_MASK, 10630 0x20); 10631 if (phy->type == 10632 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834) { 10633 /* Disable MI_INT interrupt before setting LED4 10634 * source to constant on. 10635 */ 10636 if (REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + 10637 params->port*4) & 10638 NIG_MASK_MI_INT) { 10639 params->link_flags |= 10640 LINK_FLAGS_INT_DISABLED; 10641 10642 bnx2x_bits_dis( 10643 bp, 10644 NIG_REG_MASK_INTERRUPT_PORT0 + 10645 params->port*4, 10646 NIG_MASK_MI_INT); 10647 } 10648 bnx2x_cl45_write(bp, phy, 10649 MDIO_PMA_DEVAD, 10650 MDIO_PMA_REG_8481_SIGNAL_MASK, 10651 0x20); 10652 } 10653 } 10654 break; 10655 10656 case LED_MODE_OPER: 10657 10658 DP(NETIF_MSG_LINK, "Port 0x%x: LED MODE OPER\n", port); 10659 10660 if ((params->hw_led_mode << SHARED_HW_CFG_LED_MODE_SHIFT) == 10661 SHARED_HW_CFG_LED_EXTPHY1) { 10662 10663 /* Set control reg */ 10664 bnx2x_cl45_read(bp, phy, 10665 MDIO_PMA_DEVAD, 10666 MDIO_PMA_REG_8481_LINK_SIGNAL, 10667 &val); 10668 10669 if (!((val & 10670 MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK) 10671 >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)) { 10672 DP(NETIF_MSG_LINK, "Setting LINK_SIGNAL\n"); 10673 bnx2x_cl45_write(bp, phy, 10674 MDIO_PMA_DEVAD, 10675 MDIO_PMA_REG_8481_LINK_SIGNAL, 10676 0xa492); 10677 } 10678 10679 /* Set LED masks */ 10680 bnx2x_cl45_write(bp, phy, 10681 MDIO_PMA_DEVAD, 10682 MDIO_PMA_REG_8481_LED1_MASK, 10683 0x10); 10684 10685 bnx2x_cl45_write(bp, phy, 10686 MDIO_PMA_DEVAD, 10687 MDIO_PMA_REG_8481_LED2_MASK, 10688 0x80); 10689 10690 bnx2x_cl45_write(bp, phy, 10691 MDIO_PMA_DEVAD, 10692 MDIO_PMA_REG_8481_LED3_MASK, 10693 0x98); 10694 10695 bnx2x_cl45_write(bp, phy, 10696 MDIO_PMA_DEVAD, 10697 MDIO_PMA_REG_8481_LED5_MASK, 10698 0x40); 10699 10700 } else { 10701 /* EXTPHY2 LED mode indicate that the 100M/1G/10G LED 10702 * sources are all wired through LED1, rather than only 10703 * 10G in other modes. 10704 */ 10705 val = ((params->hw_led_mode << 10706 SHARED_HW_CFG_LED_MODE_SHIFT) == 10707 SHARED_HW_CFG_LED_EXTPHY2) ? 0x98 : 0x80; 10708 10709 bnx2x_cl45_write(bp, phy, 10710 MDIO_PMA_DEVAD, 10711 MDIO_PMA_REG_8481_LED1_MASK, 10712 val); 10713 10714 /* Tell LED3 to blink on source */ 10715 bnx2x_cl45_read(bp, phy, 10716 MDIO_PMA_DEVAD, 10717 MDIO_PMA_REG_8481_LINK_SIGNAL, 10718 &val); 10719 val &= ~(7<<6); 10720 val |= (1<<6); /* A83B[8:6]= 1 */ 10721 bnx2x_cl45_write(bp, phy, 10722 MDIO_PMA_DEVAD, 10723 MDIO_PMA_REG_8481_LINK_SIGNAL, 10724 val); 10725 if (phy->type == 10726 PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834) { 10727 /* Restore LED4 source to external link, 10728 * and re-enable interrupts. 10729 */ 10730 bnx2x_cl45_write(bp, phy, 10731 MDIO_PMA_DEVAD, 10732 MDIO_PMA_REG_8481_SIGNAL_MASK, 10733 0x40); 10734 if (params->link_flags & 10735 LINK_FLAGS_INT_DISABLED) { 10736 bnx2x_link_int_enable(params); 10737 params->link_flags &= 10738 ~LINK_FLAGS_INT_DISABLED; 10739 } 10740 } 10741 } 10742 break; 10743 } 10744 10745 /* This is a workaround for E3+84833 until autoneg 10746 * restart is fixed in f/w 10747 */ 10748 if (CHIP_IS_E3(bp)) { 10749 bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD, 10750 MDIO_WC_REG_GP2_STATUS_GP_2_1, &val); 10751 } 10752} 10753 10754/******************************************************************/ 10755/* 54618SE PHY SECTION */ 10756/******************************************************************/ 10757static void bnx2x_54618se_specific_func(struct bnx2x_phy *phy, 10758 struct link_params *params, 10759 u32 action) 10760{ 10761 struct bnx2x *bp = params->bp; 10762 u16 temp; 10763 switch (action) { 10764 case PHY_INIT: 10765 /* Configure LED4: set to INTR (0x6). */ 10766 /* Accessing shadow register 0xe. */ 10767 bnx2x_cl22_write(bp, phy, 10768 MDIO_REG_GPHY_SHADOW, 10769 MDIO_REG_GPHY_SHADOW_LED_SEL2); 10770 bnx2x_cl22_read(bp, phy, 10771 MDIO_REG_GPHY_SHADOW, 10772 &temp); 10773 temp &= ~(0xf << 4); 10774 temp |= (0x6 << 4); 10775 bnx2x_cl22_write(bp, phy, 10776 MDIO_REG_GPHY_SHADOW, 10777 MDIO_REG_GPHY_SHADOW_WR_ENA | temp); 10778 /* Configure INTR based on link status change. */ 10779 bnx2x_cl22_write(bp, phy, 10780 MDIO_REG_INTR_MASK, 10781 ~MDIO_REG_INTR_MASK_LINK_STATUS); 10782 break; 10783 } 10784} 10785 10786static int bnx2x_54618se_config_init(struct bnx2x_phy *phy, 10787 struct link_params *params, 10788 struct link_vars *vars) 10789{ 10790 struct bnx2x *bp = params->bp; 10791 u8 port; 10792 u16 autoneg_val, an_1000_val, an_10_100_val, fc_val, temp; 10793 u32 cfg_pin; 10794 10795 DP(NETIF_MSG_LINK, "54618SE cfg init\n"); 10796 usleep_range(1000, 2000); 10797 10798 /* This works with E3 only, no need to check the chip 10799 * before determining the port. 10800 */ 10801 port = params->port; 10802 10803 cfg_pin = (REG_RD(bp, params->shmem_base + 10804 offsetof(struct shmem_region, 10805 dev_info.port_hw_config[port].e3_cmn_pin_cfg)) & 10806 PORT_HW_CFG_E3_PHY_RESET_MASK) >> 10807 PORT_HW_CFG_E3_PHY_RESET_SHIFT; 10808 10809 /* Drive pin high to bring the GPHY out of reset. */ 10810 bnx2x_set_cfg_pin(bp, cfg_pin, 1); 10811 10812 /* wait for GPHY to reset */ 10813 msleep(50); 10814 10815 /* reset phy */ 10816 bnx2x_cl22_write(bp, phy, 10817 MDIO_PMA_REG_CTRL, 0x8000); 10818 bnx2x_wait_reset_complete(bp, phy, params); 10819 10820 /* Wait for GPHY to reset */ 10821 msleep(50); 10822 10823 10824 bnx2x_54618se_specific_func(phy, params, PHY_INIT); 10825 /* Flip the signal detect polarity (set 0x1c.0x1e[8]). */ 10826 bnx2x_cl22_write(bp, phy, 10827 MDIO_REG_GPHY_SHADOW, 10828 MDIO_REG_GPHY_SHADOW_AUTO_DET_MED); 10829 bnx2x_cl22_read(bp, phy, 10830 MDIO_REG_GPHY_SHADOW, 10831 &temp); 10832 temp |= MDIO_REG_GPHY_SHADOW_INVERT_FIB_SD; 10833 bnx2x_cl22_write(bp, phy, 10834 MDIO_REG_GPHY_SHADOW, 10835 MDIO_REG_GPHY_SHADOW_WR_ENA | temp); 10836 10837 /* Set up fc */ 10838 /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ 10839 bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc); 10840 fc_val = 0; 10841 if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == 10842 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) 10843 fc_val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; 10844 10845 if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == 10846 MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) 10847 fc_val |= MDIO_AN_REG_ADV_PAUSE_PAUSE; 10848 10849 /* Read all advertisement */ 10850 bnx2x_cl22_read(bp, phy, 10851 0x09, 10852 &an_1000_val); 10853 10854 bnx2x_cl22_read(bp, phy, 10855 0x04, 10856 &an_10_100_val); 10857 10858 bnx2x_cl22_read(bp, phy, 10859 MDIO_PMA_REG_CTRL, 10860 &autoneg_val); 10861 10862 /* Disable forced speed */ 10863 autoneg_val &= ~((1<<6) | (1<<8) | (1<<9) | (1<<12) | (1<<13)); 10864 an_10_100_val &= ~((1<<5) | (1<<6) | (1<<7) | (1<<8) | (1<<10) | 10865 (1<<11)); 10866 10867 if (((phy->req_line_speed == SPEED_AUTO_NEG) && 10868 (phy->speed_cap_mask & 10869 PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) || 10870 (phy->req_line_speed == SPEED_1000)) { 10871 an_1000_val |= (1<<8); 10872 autoneg_val |= (1<<9 | 1<<12); 10873 if (phy->req_duplex == DUPLEX_FULL) 10874 an_1000_val |= (1<<9); 10875 DP(NETIF_MSG_LINK, "Advertising 1G\n"); 10876 } else 10877 an_1000_val &= ~((1<<8) | (1<<9)); 10878 10879 bnx2x_cl22_write(bp, phy, 10880 0x09, 10881 an_1000_val); 10882 bnx2x_cl22_read(bp, phy, 10883 0x09, 10884 &an_1000_val); 10885 10886 /* Advertise 10/100 link speed */ 10887 if (phy->req_line_speed == SPEED_AUTO_NEG) { 10888 if (phy->speed_cap_mask & 10889 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF) { 10890 an_10_100_val |= (1<<5); 10891 autoneg_val |= (1<<9 | 1<<12); 10892 DP(NETIF_MSG_LINK, "Advertising 10M-HD\n"); 10893 } 10894 if (phy->speed_cap_mask & 10895 PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL) { 10896 an_10_100_val |= (1<<6); 10897 autoneg_val |= (1<<9 | 1<<12); 10898 DP(NETIF_MSG_LINK, "Advertising 10M-FD\n"); 10899 } 10900 if (phy->speed_cap_mask & 10901 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF) { 10902 an_10_100_val |= (1<<7); 10903 autoneg_val |= (1<<9 | 1<<12); 10904 DP(NETIF_MSG_LINK, "Advertising 100M-HD\n"); 10905 } 10906 if (phy->speed_cap_mask & 10907 PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL) { 10908 an_10_100_val |= (1<<8); 10909 autoneg_val |= (1<<9 | 1<<12); 10910 DP(NETIF_MSG_LINK, "Advertising 100M-FD\n"); 10911 } 10912 } 10913 10914 /* Only 10/100 are allowed to work in FORCE mode */ 10915 if (phy->req_line_speed == SPEED_100) { 10916 autoneg_val |= (1<<13); 10917 /* Enabled AUTO-MDIX when autoneg is disabled */ 10918 bnx2x_cl22_write(bp, phy, 10919 0x18, 10920 (1<<15 | 1<<9 | 7<<0)); 10921 DP(NETIF_MSG_LINK, "Setting 100M force\n"); 10922 } 10923 if (phy->req_line_speed == SPEED_10) { 10924 /* Enabled AUTO-MDIX when autoneg is disabled */ 10925 bnx2x_cl22_write(bp, phy, 10926 0x18, 10927 (1<<15 | 1<<9 | 7<<0)); 10928 DP(NETIF_MSG_LINK, "Setting 10M force\n"); 10929 } 10930 10931 if ((phy->flags & FLAGS_EEE) && bnx2x_eee_has_cap(params)) { 10932 int rc; 10933 10934 bnx2x_cl22_write(bp, phy, MDIO_REG_GPHY_EXP_ACCESS, 10935 MDIO_REG_GPHY_EXP_ACCESS_TOP | 10936 MDIO_REG_GPHY_EXP_TOP_2K_BUF); 10937 bnx2x_cl22_read(bp, phy, MDIO_REG_GPHY_EXP_ACCESS_GATE, &temp); 10938 temp &= 0xfffe; 10939 bnx2x_cl22_write(bp, phy, MDIO_REG_GPHY_EXP_ACCESS_GATE, temp); 10940 10941 rc = bnx2x_eee_initial_config(params, vars, SHMEM_EEE_1G_ADV); 10942 if (rc) { 10943 DP(NETIF_MSG_LINK, "Failed to configure EEE timers\n"); 10944 bnx2x_eee_disable(phy, params, vars); 10945 } else if ((params->eee_mode & EEE_MODE_ADV_LPI) && 10946 (phy->req_duplex == DUPLEX_FULL) && 10947 (bnx2x_eee_calc_timer(params) || 10948 !(params->eee_mode & EEE_MODE_ENABLE_LPI))) { 10949 /* Need to advertise EEE only when requested, 10950 * and either no LPI assertion was requested, 10951 * or it was requested and a valid timer was set. 10952 * Also notice full duplex is required for EEE. 10953 */ 10954 bnx2x_eee_advertise(phy, params, vars, 10955 SHMEM_EEE_1G_ADV); 10956 } else { 10957 DP(NETIF_MSG_LINK, "Don't Advertise 1GBase-T EEE\n"); 10958 bnx2x_eee_disable(phy, params, vars); 10959 } 10960 } else { 10961 vars->eee_status &= ~SHMEM_EEE_1G_ADV << 10962 SHMEM_EEE_SUPPORTED_SHIFT; 10963 10964 if (phy->flags & FLAGS_EEE) { 10965 /* Handle legacy auto-grEEEn */ 10966 if (params->feature_config_flags & 10967 FEATURE_CONFIG_AUTOGREEEN_ENABLED) { 10968 temp = 6; 10969 DP(NETIF_MSG_LINK, "Enabling Auto-GrEEEn\n"); 10970 } else { 10971 temp = 0; 10972 DP(NETIF_MSG_LINK, "Don't Adv. EEE\n"); 10973 } 10974 bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, 10975 MDIO_AN_REG_EEE_ADV, temp); 10976 } 10977 } 10978 10979 bnx2x_cl22_write(bp, phy, 10980 0x04, 10981 an_10_100_val | fc_val); 10982 10983 if (phy->req_duplex == DUPLEX_FULL) 10984 autoneg_val |= (1<<8); 10985 10986 bnx2x_cl22_write(bp, phy, 10987 MDIO_PMA_REG_CTRL, autoneg_val); 10988 10989 return 0; 10990} 10991 10992 10993static void bnx2x_5461x_set_link_led(struct bnx2x_phy *phy, 10994 struct link_params *params, u8 mode) 10995{ 10996 struct bnx2x *bp = params->bp; 10997 u16 temp; 10998 10999 bnx2x_cl22_write(bp, phy, 11000 MDIO_REG_GPHY_SHADOW, 11001 MDIO_REG_GPHY_SHADOW_LED_SEL1); 11002 bnx2x_cl22_read(bp, phy, 11003 MDIO_REG_GPHY_SHADOW, 11004 &temp); 11005 temp &= 0xff00; 11006 11007 DP(NETIF_MSG_LINK, "54618x set link led (mode=%x)\n", mode); 11008 switch (mode) { 11009 case LED_MODE_FRONT_PANEL_OFF: 11010 case LED_MODE_OFF: 11011 temp |= 0x00ee; 11012 break; 11013 case LED_MODE_OPER: 11014 temp |= 0x0001; 11015 break; 11016 case LED_MODE_ON: 11017 temp |= 0x00ff; 11018 break; 11019 default: 11020 break; 11021 } 11022 bnx2x_cl22_write(bp, phy, 11023 MDIO_REG_GPHY_SHADOW, 11024 MDIO_REG_GPHY_SHADOW_WR_ENA | temp); 11025 return; 11026} 11027 11028 11029static void bnx2x_54618se_link_reset(struct bnx2x_phy *phy, 11030 struct link_params *params) 11031{ 11032 struct bnx2x *bp = params->bp; 11033 u32 cfg_pin; 11034 u8 port; 11035 11036 /* In case of no EPIO routed to reset the GPHY, put it 11037 * in low power mode. 11038 */ 11039 bnx2x_cl22_write(bp, phy, MDIO_PMA_REG_CTRL, 0x800); 11040 /* This works with E3 only, no need to check the chip 11041 * before determining the port. 11042 */ 11043 port = params->port; 11044 cfg_pin = (REG_RD(bp, params->shmem_base + 11045 offsetof(struct shmem_region, 11046 dev_info.port_hw_config[port].e3_cmn_pin_cfg)) & 11047 PORT_HW_CFG_E3_PHY_RESET_MASK) >> 11048 PORT_HW_CFG_E3_PHY_RESET_SHIFT; 11049 11050 /* Drive pin low to put GPHY in reset. */ 11051 bnx2x_set_cfg_pin(bp, cfg_pin, 0); 11052} 11053 11054static u8 bnx2x_54618se_read_status(struct bnx2x_phy *phy, 11055 struct link_params *params, 11056 struct link_vars *vars) 11057{ 11058 struct bnx2x *bp = params->bp; 11059 u16 val; 11060 u8 link_up = 0; 11061 u16 legacy_status, legacy_speed; 11062 11063 /* Get speed operation status */ 11064 bnx2x_cl22_read(bp, phy, 11065 MDIO_REG_GPHY_AUX_STATUS, 11066 &legacy_status); 11067 DP(NETIF_MSG_LINK, "54618SE read_status: 0x%x\n", legacy_status); 11068 11069 /* Read status to clear the PHY interrupt. */ 11070 bnx2x_cl22_read(bp, phy, 11071 MDIO_REG_INTR_STATUS, 11072 &val); 11073 11074 link_up = ((legacy_status & (1<<2)) == (1<<2)); 11075 11076 if (link_up) { 11077 legacy_speed = (legacy_status & (7<<8)); 11078 if (legacy_speed == (7<<8)) { 11079 vars->line_speed = SPEED_1000; 11080 vars->duplex = DUPLEX_FULL; 11081 } else if (legacy_speed == (6<<8)) { 11082 vars->line_speed = SPEED_1000; 11083 vars->duplex = DUPLEX_HALF; 11084 } else if (legacy_speed == (5<<8)) { 11085 vars->line_speed = SPEED_100; 11086 vars->duplex = DUPLEX_FULL; 11087 } 11088 /* Omitting 100Base-T4 for now */ 11089 else if (legacy_speed == (3<<8)) { 11090 vars->line_speed = SPEED_100; 11091 vars->duplex = DUPLEX_HALF; 11092 } else if (legacy_speed == (2<<8)) { 11093 vars->line_speed = SPEED_10; 11094 vars->duplex = DUPLEX_FULL; 11095 } else if (legacy_speed == (1<<8)) { 11096 vars->line_speed = SPEED_10; 11097 vars->duplex = DUPLEX_HALF; 11098 } else /* Should not happen */ 11099 vars->line_speed = 0; 11100 11101 DP(NETIF_MSG_LINK, 11102 "Link is up in %dMbps, is_duplex_full= %d\n", 11103 vars->line_speed, 11104 (vars->duplex == DUPLEX_FULL)); 11105 11106 /* Check legacy speed AN resolution */ 11107 bnx2x_cl22_read(bp, phy, 11108 0x01, 11109 &val); 11110 if (val & (1<<5)) 11111 vars->link_status |= 11112 LINK_STATUS_AUTO_NEGOTIATE_COMPLETE; 11113 bnx2x_cl22_read(bp, phy, 11114 0x06, 11115 &val); 11116 if ((val & (1<<0)) == 0) 11117 vars->link_status |= 11118 LINK_STATUS_PARALLEL_DETECTION_USED; 11119 11120 DP(NETIF_MSG_LINK, "BCM54618SE: link speed is %d\n", 11121 vars->line_speed); 11122 11123 bnx2x_ext_phy_resolve_fc(phy, params, vars); 11124 11125 if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) { 11126 /* Report LP advertised speeds */ 11127 bnx2x_cl22_read(bp, phy, 0x5, &val); 11128 11129 if (val & (1<<5)) 11130 vars->link_status |= 11131 LINK_STATUS_LINK_PARTNER_10THD_CAPABLE; 11132 if (val & (1<<6)) 11133 vars->link_status |= 11134 LINK_STATUS_LINK_PARTNER_10TFD_CAPABLE; 11135 if (val & (1<<7)) 11136 vars->link_status |= 11137 LINK_STATUS_LINK_PARTNER_100TXHD_CAPABLE; 11138 if (val & (1<<8)) 11139 vars->link_status |= 11140 LINK_STATUS_LINK_PARTNER_100TXFD_CAPABLE; 11141 if (val & (1<<9)) 11142 vars->link_status |= 11143 LINK_STATUS_LINK_PARTNER_100T4_CAPABLE; 11144 11145 bnx2x_cl22_read(bp, phy, 0xa, &val); 11146 if (val & (1<<10)) 11147 vars->link_status |= 11148 LINK_STATUS_LINK_PARTNER_1000THD_CAPABLE; 11149 if (val & (1<<11)) 11150 vars->link_status |= 11151 LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE; 11152 11153 if ((phy->flags & FLAGS_EEE) && 11154 bnx2x_eee_has_cap(params)) 11155 bnx2x_eee_an_resolve(phy, params, vars); 11156 } 11157 } 11158 return link_up; 11159} 11160 11161static void bnx2x_54618se_config_loopback(struct bnx2x_phy *phy, 11162 struct link_params *params) 11163{ 11164 struct bnx2x *bp = params->bp; 11165 u16 val; 11166 u32 umac_base = params->port ? GRCBASE_UMAC1 : GRCBASE_UMAC0; 11167 11168 DP(NETIF_MSG_LINK, "2PMA/PMD ext_phy_loopback: 54618se\n"); 11169 11170 /* Enable master/slave manual mmode and set to master */ 11171 /* mii write 9 [bits set 11 12] */ 11172 bnx2x_cl22_write(bp, phy, 0x09, 3<<11); 11173 11174 /* forced 1G and disable autoneg */ 11175 /* set val [mii read 0] */ 11176 /* set val [expr $val & [bits clear 6 12 13]] */ 11177 /* set val [expr $val | [bits set 6 8]] */ 11178 /* mii write 0 $val */ 11179 bnx2x_cl22_read(bp, phy, 0x00, &val); 11180 val &= ~((1<<6) | (1<<12) | (1<<13)); 11181 val |= (1<<6) | (1<<8); 11182 bnx2x_cl22_write(bp, phy, 0x00, val); 11183 11184 /* Set external loopback and Tx using 6dB coding */ 11185 /* mii write 0x18 7 */ 11186 /* set val [mii read 0x18] */ 11187 /* mii write 0x18 [expr $val | [bits set 10 15]] */ 11188 bnx2x_cl22_write(bp, phy, 0x18, 7); 11189 bnx2x_cl22_read(bp, phy, 0x18, &val); 11190 bnx2x_cl22_write(bp, phy, 0x18, val | (1<<10) | (1<<15)); 11191 11192 /* This register opens the gate for the UMAC despite its name */ 11193 REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4, 1); 11194 11195 /* Maximum Frame Length (RW). Defines a 14-Bit maximum frame 11196 * length used by the MAC receive logic to check frames. 11197 */ 11198 REG_WR(bp, umac_base + UMAC_REG_MAXFR, 0x2710); 11199} 11200 11201/******************************************************************/ 11202/* SFX7101 PHY SECTION */ 11203/******************************************************************/ 11204static void bnx2x_7101_config_loopback(struct bnx2x_phy *phy, 11205 struct link_params *params) 11206{ 11207 struct bnx2x *bp = params->bp; 11208 /* SFX7101_XGXS_TEST1 */ 11209 bnx2x_cl45_write(bp, phy, 11210 MDIO_XS_DEVAD, MDIO_XS_SFX7101_XGXS_TEST1, 0x100); 11211} 11212 11213static int bnx2x_7101_config_init(struct bnx2x_phy *phy, 11214 struct link_params *params, 11215 struct link_vars *vars) 11216{ 11217 u16 fw_ver1, fw_ver2, val; 11218 struct bnx2x *bp = params->bp; 11219 DP(NETIF_MSG_LINK, "Setting the SFX7101 LASI indication\n"); 11220 11221 /* Restore normal power mode*/ 11222 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 11223 MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); 11224 /* HW reset */ 11225 bnx2x_ext_phy_hw_reset(bp, params->port); 11226 bnx2x_wait_reset_complete(bp, phy, params); 11227 11228 bnx2x_cl45_write(bp, phy, 11229 MDIO_PMA_DEVAD, MDIO_PMA_LASI_CTRL, 0x1); 11230 DP(NETIF_MSG_LINK, "Setting the SFX7101 LED to blink on traffic\n"); 11231 bnx2x_cl45_write(bp, phy, 11232 MDIO_PMA_DEVAD, MDIO_PMA_REG_7107_LED_CNTL, (1<<3)); 11233 11234 bnx2x_ext_phy_set_pause(params, phy, vars); 11235 /* Restart autoneg */ 11236 bnx2x_cl45_read(bp, phy, 11237 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, &val); 11238 val |= 0x200; 11239 bnx2x_cl45_write(bp, phy, 11240 MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, val); 11241 11242 /* Save spirom version */ 11243 bnx2x_cl45_read(bp, phy, 11244 MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER1, &fw_ver1); 11245 11246 bnx2x_cl45_read(bp, phy, 11247 MDIO_PMA_DEVAD, MDIO_PMA_REG_7101_VER2, &fw_ver2); 11248 bnx2x_save_spirom_version(bp, params->port, 11249 (u32)(fw_ver1<<16 | fw_ver2), phy->ver_addr); 11250 return 0; 11251} 11252 11253static u8 bnx2x_7101_read_status(struct bnx2x_phy *phy, 11254 struct link_params *params, 11255 struct link_vars *vars) 11256{ 11257 struct bnx2x *bp = params->bp; 11258 u8 link_up; 11259 u16 val1, val2; 11260 bnx2x_cl45_read(bp, phy, 11261 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val2); 11262 bnx2x_cl45_read(bp, phy, 11263 MDIO_PMA_DEVAD, MDIO_PMA_LASI_STAT, &val1); 11264 DP(NETIF_MSG_LINK, "10G-base-T LASI status 0x%x->0x%x\n", 11265 val2, val1); 11266 bnx2x_cl45_read(bp, phy, 11267 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val2); 11268 bnx2x_cl45_read(bp, phy, 11269 MDIO_PMA_DEVAD, MDIO_PMA_REG_STATUS, &val1); 11270 DP(NETIF_MSG_LINK, "10G-base-T PMA status 0x%x->0x%x\n", 11271 val2, val1); 11272 link_up = ((val1 & 4) == 4); 11273 /* If link is up print the AN outcome of the SFX7101 PHY */ 11274 if (link_up) { 11275 bnx2x_cl45_read(bp, phy, 11276 MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS, 11277 &val2); 11278 vars->line_speed = SPEED_10000; 11279 vars->duplex = DUPLEX_FULL; 11280 DP(NETIF_MSG_LINK, "SFX7101 AN status 0x%x->Master=%x\n", 11281 val2, (val2 & (1<<14))); 11282 bnx2x_ext_phy_10G_an_resolve(bp, phy, vars); 11283 bnx2x_ext_phy_resolve_fc(phy, params, vars); 11284 11285 /* Read LP advertised speeds */ 11286 if (val2 & (1<<11)) 11287 vars->link_status |= 11288 LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE; 11289 } 11290 return link_up; 11291} 11292 11293static int bnx2x_7101_format_ver(u32 spirom_ver, u8 *str, u16 *len) 11294{ 11295 if (*len < 5) 11296 return -EINVAL; 11297 str[0] = (spirom_ver & 0xFF); 11298 str[1] = (spirom_ver & 0xFF00) >> 8; 11299 str[2] = (spirom_ver & 0xFF0000) >> 16; 11300 str[3] = (spirom_ver & 0xFF000000) >> 24; 11301 str[4] = '\0'; 11302 *len -= 5; 11303 return 0; 11304} 11305 11306void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy) 11307{ 11308 u16 val, cnt; 11309 11310 bnx2x_cl45_read(bp, phy, 11311 MDIO_PMA_DEVAD, 11312 MDIO_PMA_REG_7101_RESET, &val); 11313 11314 for (cnt = 0; cnt < 10; cnt++) { 11315 msleep(50); 11316 /* Writes a self-clearing reset */ 11317 bnx2x_cl45_write(bp, phy, 11318 MDIO_PMA_DEVAD, 11319 MDIO_PMA_REG_7101_RESET, 11320 (val | (1<<15))); 11321 /* Wait for clear */ 11322 bnx2x_cl45_read(bp, phy, 11323 MDIO_PMA_DEVAD, 11324 MDIO_PMA_REG_7101_RESET, &val); 11325 11326 if ((val & (1<<15)) == 0) 11327 break; 11328 } 11329} 11330 11331static void bnx2x_7101_hw_reset(struct bnx2x_phy *phy, 11332 struct link_params *params) { 11333 /* Low power mode is controlled by GPIO 2 */ 11334 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2, 11335 MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); 11336 /* The PHY reset is controlled by GPIO 1 */ 11337 bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, 11338 MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); 11339} 11340 11341static void bnx2x_7101_set_link_led(struct bnx2x_phy *phy, 11342 struct link_params *params, u8 mode) 11343{ 11344 u16 val = 0; 11345 struct bnx2x *bp = params->bp; 11346 switch (mode) { 11347 case LED_MODE_FRONT_PANEL_OFF: 11348 case LED_MODE_OFF: 11349 val = 2; 11350 break; 11351 case LED_MODE_ON: 11352 val = 1; 11353 break; 11354 case LED_MODE_OPER: 11355 val = 0; 11356 break; 11357 } 11358 bnx2x_cl45_write(bp, phy, 11359 MDIO_PMA_DEVAD, 11360 MDIO_PMA_REG_7107_LINK_LED_CNTL, 11361 val); 11362} 11363 11364/******************************************************************/ 11365/* STATIC PHY DECLARATION */ 11366/******************************************************************/ 11367 11368static const struct bnx2x_phy phy_null = { 11369 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN, 11370 .addr = 0, 11371 .def_md_devad = 0, 11372 .flags = FLAGS_INIT_XGXS_FIRST, 11373 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11374 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11375 .mdio_ctrl = 0, 11376 .supported = 0, 11377 .media_type = ETH_PHY_NOT_PRESENT, 11378 .ver_addr = 0, 11379 .req_flow_ctrl = 0, 11380 .req_line_speed = 0, 11381 .speed_cap_mask = 0, 11382 .req_duplex = 0, 11383 .rsrv = 0, 11384 .config_init = (config_init_t)NULL, 11385 .read_status = (read_status_t)NULL, 11386 .link_reset = (link_reset_t)NULL, 11387 .config_loopback = (config_loopback_t)NULL, 11388 .format_fw_ver = (format_fw_ver_t)NULL, 11389 .hw_reset = (hw_reset_t)NULL, 11390 .set_link_led = (set_link_led_t)NULL, 11391 .phy_specific_func = (phy_specific_func_t)NULL 11392}; 11393 11394static const struct bnx2x_phy phy_serdes = { 11395 .type = PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT, 11396 .addr = 0xff, 11397 .def_md_devad = 0, 11398 .flags = 0, 11399 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11400 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11401 .mdio_ctrl = 0, 11402 .supported = (SUPPORTED_10baseT_Half | 11403 SUPPORTED_10baseT_Full | 11404 SUPPORTED_100baseT_Half | 11405 SUPPORTED_100baseT_Full | 11406 SUPPORTED_1000baseT_Full | 11407 SUPPORTED_2500baseX_Full | 11408 SUPPORTED_TP | 11409 SUPPORTED_Autoneg | 11410 SUPPORTED_Pause | 11411 SUPPORTED_Asym_Pause), 11412 .media_type = ETH_PHY_BASE_T, 11413 .ver_addr = 0, 11414 .req_flow_ctrl = 0, 11415 .req_line_speed = 0, 11416 .speed_cap_mask = 0, 11417 .req_duplex = 0, 11418 .rsrv = 0, 11419 .config_init = (config_init_t)bnx2x_xgxs_config_init, 11420 .read_status = (read_status_t)bnx2x_link_settings_status, 11421 .link_reset = (link_reset_t)bnx2x_int_link_reset, 11422 .config_loopback = (config_loopback_t)NULL, 11423 .format_fw_ver = (format_fw_ver_t)NULL, 11424 .hw_reset = (hw_reset_t)NULL, 11425 .set_link_led = (set_link_led_t)NULL, 11426 .phy_specific_func = (phy_specific_func_t)NULL 11427}; 11428 11429static const struct bnx2x_phy phy_xgxs = { 11430 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT, 11431 .addr = 0xff, 11432 .def_md_devad = 0, 11433 .flags = 0, 11434 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11435 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11436 .mdio_ctrl = 0, 11437 .supported = (SUPPORTED_10baseT_Half | 11438 SUPPORTED_10baseT_Full | 11439 SUPPORTED_100baseT_Half | 11440 SUPPORTED_100baseT_Full | 11441 SUPPORTED_1000baseT_Full | 11442 SUPPORTED_2500baseX_Full | 11443 SUPPORTED_10000baseT_Full | 11444 SUPPORTED_FIBRE | 11445 SUPPORTED_Autoneg | 11446 SUPPORTED_Pause | 11447 SUPPORTED_Asym_Pause), 11448 .media_type = ETH_PHY_CX4, 11449 .ver_addr = 0, 11450 .req_flow_ctrl = 0, 11451 .req_line_speed = 0, 11452 .speed_cap_mask = 0, 11453 .req_duplex = 0, 11454 .rsrv = 0, 11455 .config_init = (config_init_t)bnx2x_xgxs_config_init, 11456 .read_status = (read_status_t)bnx2x_link_settings_status, 11457 .link_reset = (link_reset_t)bnx2x_int_link_reset, 11458 .config_loopback = (config_loopback_t)bnx2x_set_xgxs_loopback, 11459 .format_fw_ver = (format_fw_ver_t)NULL, 11460 .hw_reset = (hw_reset_t)NULL, 11461 .set_link_led = (set_link_led_t)NULL, 11462 .phy_specific_func = (phy_specific_func_t)bnx2x_xgxs_specific_func 11463}; 11464static const struct bnx2x_phy phy_warpcore = { 11465 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT, 11466 .addr = 0xff, 11467 .def_md_devad = 0, 11468 .flags = FLAGS_TX_ERROR_CHECK, 11469 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11470 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11471 .mdio_ctrl = 0, 11472 .supported = (SUPPORTED_10baseT_Half | 11473 SUPPORTED_10baseT_Full | 11474 SUPPORTED_100baseT_Half | 11475 SUPPORTED_100baseT_Full | 11476 SUPPORTED_1000baseT_Full | 11477 SUPPORTED_10000baseT_Full | 11478 SUPPORTED_20000baseKR2_Full | 11479 SUPPORTED_20000baseMLD2_Full | 11480 SUPPORTED_FIBRE | 11481 SUPPORTED_Autoneg | 11482 SUPPORTED_Pause | 11483 SUPPORTED_Asym_Pause), 11484 .media_type = ETH_PHY_UNSPECIFIED, 11485 .ver_addr = 0, 11486 .req_flow_ctrl = 0, 11487 .req_line_speed = 0, 11488 .speed_cap_mask = 0, 11489 /* req_duplex = */0, 11490 /* rsrv = */0, 11491 .config_init = (config_init_t)bnx2x_warpcore_config_init, 11492 .read_status = (read_status_t)bnx2x_warpcore_read_status, 11493 .link_reset = (link_reset_t)bnx2x_warpcore_link_reset, 11494 .config_loopback = (config_loopback_t)bnx2x_set_warpcore_loopback, 11495 .format_fw_ver = (format_fw_ver_t)NULL, 11496 .hw_reset = (hw_reset_t)bnx2x_warpcore_hw_reset, 11497 .set_link_led = (set_link_led_t)NULL, 11498 .phy_specific_func = (phy_specific_func_t)NULL 11499}; 11500 11501 11502static const struct bnx2x_phy phy_7101 = { 11503 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, 11504 .addr = 0xff, 11505 .def_md_devad = 0, 11506 .flags = FLAGS_FAN_FAILURE_DET_REQ, 11507 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11508 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11509 .mdio_ctrl = 0, 11510 .supported = (SUPPORTED_10000baseT_Full | 11511 SUPPORTED_TP | 11512 SUPPORTED_Autoneg | 11513 SUPPORTED_Pause | 11514 SUPPORTED_Asym_Pause), 11515 .media_type = ETH_PHY_BASE_T, 11516 .ver_addr = 0, 11517 .req_flow_ctrl = 0, 11518 .req_line_speed = 0, 11519 .speed_cap_mask = 0, 11520 .req_duplex = 0, 11521 .rsrv = 0, 11522 .config_init = (config_init_t)bnx2x_7101_config_init, 11523 .read_status = (read_status_t)bnx2x_7101_read_status, 11524 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset, 11525 .config_loopback = (config_loopback_t)bnx2x_7101_config_loopback, 11526 .format_fw_ver = (format_fw_ver_t)bnx2x_7101_format_ver, 11527 .hw_reset = (hw_reset_t)bnx2x_7101_hw_reset, 11528 .set_link_led = (set_link_led_t)bnx2x_7101_set_link_led, 11529 .phy_specific_func = (phy_specific_func_t)NULL 11530}; 11531static const struct bnx2x_phy phy_8073 = { 11532 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, 11533 .addr = 0xff, 11534 .def_md_devad = 0, 11535 .flags = 0, 11536 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11537 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11538 .mdio_ctrl = 0, 11539 .supported = (SUPPORTED_10000baseT_Full | 11540 SUPPORTED_2500baseX_Full | 11541 SUPPORTED_1000baseT_Full | 11542 SUPPORTED_FIBRE | 11543 SUPPORTED_Autoneg | 11544 SUPPORTED_Pause | 11545 SUPPORTED_Asym_Pause), 11546 .media_type = ETH_PHY_KR, 11547 .ver_addr = 0, 11548 .req_flow_ctrl = 0, 11549 .req_line_speed = 0, 11550 .speed_cap_mask = 0, 11551 .req_duplex = 0, 11552 .rsrv = 0, 11553 .config_init = (config_init_t)bnx2x_8073_config_init, 11554 .read_status = (read_status_t)bnx2x_8073_read_status, 11555 .link_reset = (link_reset_t)bnx2x_8073_link_reset, 11556 .config_loopback = (config_loopback_t)NULL, 11557 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver, 11558 .hw_reset = (hw_reset_t)NULL, 11559 .set_link_led = (set_link_led_t)NULL, 11560 .phy_specific_func = (phy_specific_func_t)bnx2x_8073_specific_func 11561}; 11562static const struct bnx2x_phy phy_8705 = { 11563 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705, 11564 .addr = 0xff, 11565 .def_md_devad = 0, 11566 .flags = FLAGS_INIT_XGXS_FIRST, 11567 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11568 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11569 .mdio_ctrl = 0, 11570 .supported = (SUPPORTED_10000baseT_Full | 11571 SUPPORTED_FIBRE | 11572 SUPPORTED_Pause | 11573 SUPPORTED_Asym_Pause), 11574 .media_type = ETH_PHY_XFP_FIBER, 11575 .ver_addr = 0, 11576 .req_flow_ctrl = 0, 11577 .req_line_speed = 0, 11578 .speed_cap_mask = 0, 11579 .req_duplex = 0, 11580 .rsrv = 0, 11581 .config_init = (config_init_t)bnx2x_8705_config_init, 11582 .read_status = (read_status_t)bnx2x_8705_read_status, 11583 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset, 11584 .config_loopback = (config_loopback_t)NULL, 11585 .format_fw_ver = (format_fw_ver_t)bnx2x_null_format_ver, 11586 .hw_reset = (hw_reset_t)NULL, 11587 .set_link_led = (set_link_led_t)NULL, 11588 .phy_specific_func = (phy_specific_func_t)NULL 11589}; 11590static const struct bnx2x_phy phy_8706 = { 11591 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706, 11592 .addr = 0xff, 11593 .def_md_devad = 0, 11594 .flags = FLAGS_INIT_XGXS_FIRST, 11595 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11596 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11597 .mdio_ctrl = 0, 11598 .supported = (SUPPORTED_10000baseT_Full | 11599 SUPPORTED_1000baseT_Full | 11600 SUPPORTED_FIBRE | 11601 SUPPORTED_Pause | 11602 SUPPORTED_Asym_Pause), 11603 .media_type = ETH_PHY_SFPP_10G_FIBER, 11604 .ver_addr = 0, 11605 .req_flow_ctrl = 0, 11606 .req_line_speed = 0, 11607 .speed_cap_mask = 0, 11608 .req_duplex = 0, 11609 .rsrv = 0, 11610 .config_init = (config_init_t)bnx2x_8706_config_init, 11611 .read_status = (read_status_t)bnx2x_8706_read_status, 11612 .link_reset = (link_reset_t)bnx2x_common_ext_link_reset, 11613 .config_loopback = (config_loopback_t)NULL, 11614 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver, 11615 .hw_reset = (hw_reset_t)NULL, 11616 .set_link_led = (set_link_led_t)NULL, 11617 .phy_specific_func = (phy_specific_func_t)NULL 11618}; 11619 11620static const struct bnx2x_phy phy_8726 = { 11621 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726, 11622 .addr = 0xff, 11623 .def_md_devad = 0, 11624 .flags = (FLAGS_INIT_XGXS_FIRST | 11625 FLAGS_TX_ERROR_CHECK), 11626 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11627 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11628 .mdio_ctrl = 0, 11629 .supported = (SUPPORTED_10000baseT_Full | 11630 SUPPORTED_1000baseT_Full | 11631 SUPPORTED_Autoneg | 11632 SUPPORTED_FIBRE | 11633 SUPPORTED_Pause | 11634 SUPPORTED_Asym_Pause), 11635 .media_type = ETH_PHY_NOT_PRESENT, 11636 .ver_addr = 0, 11637 .req_flow_ctrl = 0, 11638 .req_line_speed = 0, 11639 .speed_cap_mask = 0, 11640 .req_duplex = 0, 11641 .rsrv = 0, 11642 .config_init = (config_init_t)bnx2x_8726_config_init, 11643 .read_status = (read_status_t)bnx2x_8726_read_status, 11644 .link_reset = (link_reset_t)bnx2x_8726_link_reset, 11645 .config_loopback = (config_loopback_t)bnx2x_8726_config_loopback, 11646 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver, 11647 .hw_reset = (hw_reset_t)NULL, 11648 .set_link_led = (set_link_led_t)NULL, 11649 .phy_specific_func = (phy_specific_func_t)NULL 11650}; 11651 11652static const struct bnx2x_phy phy_8727 = { 11653 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727, 11654 .addr = 0xff, 11655 .def_md_devad = 0, 11656 .flags = (FLAGS_FAN_FAILURE_DET_REQ | 11657 FLAGS_TX_ERROR_CHECK), 11658 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11659 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11660 .mdio_ctrl = 0, 11661 .supported = (SUPPORTED_10000baseT_Full | 11662 SUPPORTED_1000baseT_Full | 11663 SUPPORTED_FIBRE | 11664 SUPPORTED_Pause | 11665 SUPPORTED_Asym_Pause), 11666 .media_type = ETH_PHY_NOT_PRESENT, 11667 .ver_addr = 0, 11668 .req_flow_ctrl = 0, 11669 .req_line_speed = 0, 11670 .speed_cap_mask = 0, 11671 .req_duplex = 0, 11672 .rsrv = 0, 11673 .config_init = (config_init_t)bnx2x_8727_config_init, 11674 .read_status = (read_status_t)bnx2x_8727_read_status, 11675 .link_reset = (link_reset_t)bnx2x_8727_link_reset, 11676 .config_loopback = (config_loopback_t)NULL, 11677 .format_fw_ver = (format_fw_ver_t)bnx2x_format_ver, 11678 .hw_reset = (hw_reset_t)bnx2x_8727_hw_reset, 11679 .set_link_led = (set_link_led_t)bnx2x_8727_set_link_led, 11680 .phy_specific_func = (phy_specific_func_t)bnx2x_8727_specific_func 11681}; 11682static const struct bnx2x_phy phy_8481 = { 11683 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481, 11684 .addr = 0xff, 11685 .def_md_devad = 0, 11686 .flags = FLAGS_FAN_FAILURE_DET_REQ | 11687 FLAGS_REARM_LATCH_SIGNAL, 11688 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11689 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11690 .mdio_ctrl = 0, 11691 .supported = (SUPPORTED_10baseT_Half | 11692 SUPPORTED_10baseT_Full | 11693 SUPPORTED_100baseT_Half | 11694 SUPPORTED_100baseT_Full | 11695 SUPPORTED_1000baseT_Full | 11696 SUPPORTED_10000baseT_Full | 11697 SUPPORTED_TP | 11698 SUPPORTED_Autoneg | 11699 SUPPORTED_Pause | 11700 SUPPORTED_Asym_Pause), 11701 .media_type = ETH_PHY_BASE_T, 11702 .ver_addr = 0, 11703 .req_flow_ctrl = 0, 11704 .req_line_speed = 0, 11705 .speed_cap_mask = 0, 11706 .req_duplex = 0, 11707 .rsrv = 0, 11708 .config_init = (config_init_t)bnx2x_8481_config_init, 11709 .read_status = (read_status_t)bnx2x_848xx_read_status, 11710 .link_reset = (link_reset_t)bnx2x_8481_link_reset, 11711 .config_loopback = (config_loopback_t)NULL, 11712 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver, 11713 .hw_reset = (hw_reset_t)bnx2x_8481_hw_reset, 11714 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led, 11715 .phy_specific_func = (phy_specific_func_t)NULL 11716}; 11717 11718static const struct bnx2x_phy phy_84823 = { 11719 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823, 11720 .addr = 0xff, 11721 .def_md_devad = 0, 11722 .flags = (FLAGS_FAN_FAILURE_DET_REQ | 11723 FLAGS_REARM_LATCH_SIGNAL | 11724 FLAGS_TX_ERROR_CHECK), 11725 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11726 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11727 .mdio_ctrl = 0, 11728 .supported = (SUPPORTED_10baseT_Half | 11729 SUPPORTED_10baseT_Full | 11730 SUPPORTED_100baseT_Half | 11731 SUPPORTED_100baseT_Full | 11732 SUPPORTED_1000baseT_Full | 11733 SUPPORTED_10000baseT_Full | 11734 SUPPORTED_TP | 11735 SUPPORTED_Autoneg | 11736 SUPPORTED_Pause | 11737 SUPPORTED_Asym_Pause), 11738 .media_type = ETH_PHY_BASE_T, 11739 .ver_addr = 0, 11740 .req_flow_ctrl = 0, 11741 .req_line_speed = 0, 11742 .speed_cap_mask = 0, 11743 .req_duplex = 0, 11744 .rsrv = 0, 11745 .config_init = (config_init_t)bnx2x_848x3_config_init, 11746 .read_status = (read_status_t)bnx2x_848xx_read_status, 11747 .link_reset = (link_reset_t)bnx2x_848x3_link_reset, 11748 .config_loopback = (config_loopback_t)NULL, 11749 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver, 11750 .hw_reset = (hw_reset_t)NULL, 11751 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led, 11752 .phy_specific_func = (phy_specific_func_t)bnx2x_848xx_specific_func 11753}; 11754 11755static const struct bnx2x_phy phy_84833 = { 11756 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833, 11757 .addr = 0xff, 11758 .def_md_devad = 0, 11759 .flags = (FLAGS_FAN_FAILURE_DET_REQ | 11760 FLAGS_REARM_LATCH_SIGNAL | 11761 FLAGS_TX_ERROR_CHECK), 11762 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11763 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11764 .mdio_ctrl = 0, 11765 .supported = (SUPPORTED_100baseT_Half | 11766 SUPPORTED_100baseT_Full | 11767 SUPPORTED_1000baseT_Full | 11768 SUPPORTED_10000baseT_Full | 11769 SUPPORTED_TP | 11770 SUPPORTED_Autoneg | 11771 SUPPORTED_Pause | 11772 SUPPORTED_Asym_Pause), 11773 .media_type = ETH_PHY_BASE_T, 11774 .ver_addr = 0, 11775 .req_flow_ctrl = 0, 11776 .req_line_speed = 0, 11777 .speed_cap_mask = 0, 11778 .req_duplex = 0, 11779 .rsrv = 0, 11780 .config_init = (config_init_t)bnx2x_848x3_config_init, 11781 .read_status = (read_status_t)bnx2x_848xx_read_status, 11782 .link_reset = (link_reset_t)bnx2x_848x3_link_reset, 11783 .config_loopback = (config_loopback_t)NULL, 11784 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver, 11785 .hw_reset = (hw_reset_t)bnx2x_84833_hw_reset_phy, 11786 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led, 11787 .phy_specific_func = (phy_specific_func_t)bnx2x_848xx_specific_func 11788}; 11789 11790static const struct bnx2x_phy phy_84834 = { 11791 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834, 11792 .addr = 0xff, 11793 .def_md_devad = 0, 11794 .flags = FLAGS_FAN_FAILURE_DET_REQ | 11795 FLAGS_REARM_LATCH_SIGNAL, 11796 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11797 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11798 .mdio_ctrl = 0, 11799 .supported = (SUPPORTED_100baseT_Half | 11800 SUPPORTED_100baseT_Full | 11801 SUPPORTED_1000baseT_Full | 11802 SUPPORTED_10000baseT_Full | 11803 SUPPORTED_TP | 11804 SUPPORTED_Autoneg | 11805 SUPPORTED_Pause | 11806 SUPPORTED_Asym_Pause), 11807 .media_type = ETH_PHY_BASE_T, 11808 .ver_addr = 0, 11809 .req_flow_ctrl = 0, 11810 .req_line_speed = 0, 11811 .speed_cap_mask = 0, 11812 .req_duplex = 0, 11813 .rsrv = 0, 11814 .config_init = (config_init_t)bnx2x_848x3_config_init, 11815 .read_status = (read_status_t)bnx2x_848xx_read_status, 11816 .link_reset = (link_reset_t)bnx2x_848x3_link_reset, 11817 .config_loopback = (config_loopback_t)NULL, 11818 .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver, 11819 .hw_reset = (hw_reset_t)bnx2x_84833_hw_reset_phy, 11820 .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led, 11821 .phy_specific_func = (phy_specific_func_t)bnx2x_848xx_specific_func 11822}; 11823 11824static const struct bnx2x_phy phy_54618se = { 11825 .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE, 11826 .addr = 0xff, 11827 .def_md_devad = 0, 11828 .flags = FLAGS_INIT_XGXS_FIRST, 11829 .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11830 .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, 11831 .mdio_ctrl = 0, 11832 .supported = (SUPPORTED_10baseT_Half | 11833 SUPPORTED_10baseT_Full | 11834 SUPPORTED_100baseT_Half | 11835 SUPPORTED_100baseT_Full | 11836 SUPPORTED_1000baseT_Full | 11837 SUPPORTED_TP | 11838 SUPPORTED_Autoneg | 11839 SUPPORTED_Pause | 11840 SUPPORTED_Asym_Pause), 11841 .media_type = ETH_PHY_BASE_T, 11842 .ver_addr = 0, 11843 .req_flow_ctrl = 0, 11844 .req_line_speed = 0, 11845 .speed_cap_mask = 0, 11846 /* req_duplex = */0, 11847 /* rsrv = */0, 11848 .config_init = (config_init_t)bnx2x_54618se_config_init, 11849 .read_status = (read_status_t)bnx2x_54618se_read_status, 11850 .link_reset = (link_reset_t)bnx2x_54618se_link_reset, 11851 .config_loopback = (config_loopback_t)bnx2x_54618se_config_loopback, 11852 .format_fw_ver = (format_fw_ver_t)NULL, 11853 .hw_reset = (hw_reset_t)NULL, 11854 .set_link_led = (set_link_led_t)bnx2x_5461x_set_link_led, 11855 .phy_specific_func = (phy_specific_func_t)bnx2x_54618se_specific_func 11856}; 11857/*****************************************************************/ 11858/* */ 11859/* Populate the phy according. Main function: bnx2x_populate_phy */ 11860/* */ 11861/*****************************************************************/ 11862 11863static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base, 11864 struct bnx2x_phy *phy, u8 port, 11865 u8 phy_index) 11866{ 11867 /* Get the 4 lanes xgxs config rx and tx */ 11868 u32 rx = 0, tx = 0, i; 11869 for (i = 0; i < 2; i++) { 11870 /* INT_PHY and EXT_PHY1 share the same value location in 11871 * the shmem. When num_phys is greater than 1, than this value 11872 * applies only to EXT_PHY1 11873 */ 11874 if (phy_index == INT_PHY || phy_index == EXT_PHY1) { 11875 rx = REG_RD(bp, shmem_base + 11876 offsetof(struct shmem_region, 11877 dev_info.port_hw_config[port].xgxs_config_rx[i<<1])); 11878 11879 tx = REG_RD(bp, shmem_base + 11880 offsetof(struct shmem_region, 11881 dev_info.port_hw_config[port].xgxs_config_tx[i<<1])); 11882 } else { 11883 rx = REG_RD(bp, shmem_base + 11884 offsetof(struct shmem_region, 11885 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); 11886 11887 tx = REG_RD(bp, shmem_base + 11888 offsetof(struct shmem_region, 11889 dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); 11890 } 11891 11892 phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff); 11893 phy->rx_preemphasis[(i << 1) + 1] = (rx & 0xffff); 11894 11895 phy->tx_preemphasis[i << 1] = ((tx>>16) & 0xffff); 11896 phy->tx_preemphasis[(i << 1) + 1] = (tx & 0xffff); 11897 } 11898} 11899 11900static u32 bnx2x_get_ext_phy_config(struct bnx2x *bp, u32 shmem_base, 11901 u8 phy_index, u8 port) 11902{ 11903 u32 ext_phy_config = 0; 11904 switch (phy_index) { 11905 case EXT_PHY1: 11906 ext_phy_config = REG_RD(bp, shmem_base + 11907 offsetof(struct shmem_region, 11908 dev_info.port_hw_config[port].external_phy_config)); 11909 break; 11910 case EXT_PHY2: 11911 ext_phy_config = REG_RD(bp, shmem_base + 11912 offsetof(struct shmem_region, 11913 dev_info.port_hw_config[port].external_phy_config2)); 11914 break; 11915 default: 11916 DP(NETIF_MSG_LINK, "Invalid phy_index %d\n", phy_index); 11917 return -EINVAL; 11918 } 11919 11920 return ext_phy_config; 11921} 11922static int bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port, 11923 struct bnx2x_phy *phy) 11924{ 11925 u32 phy_addr; 11926 u32 chip_id; 11927 u32 switch_cfg = (REG_RD(bp, shmem_base + 11928 offsetof(struct shmem_region, 11929 dev_info.port_feature_config[port].link_config)) & 11930 PORT_FEATURE_CONNECTED_SWITCH_MASK); 11931 chip_id = (REG_RD(bp, MISC_REG_CHIP_NUM) << 16) | 11932 ((REG_RD(bp, MISC_REG_CHIP_REV) & 0xf) << 12); 11933 11934 DP(NETIF_MSG_LINK, ":chip_id = 0x%x\n", chip_id); 11935 if (USES_WARPCORE(bp)) { 11936 u32 serdes_net_if; 11937 phy_addr = REG_RD(bp, 11938 MISC_REG_WC0_CTRL_PHY_ADDR); 11939 *phy = phy_warpcore; 11940 if (REG_RD(bp, MISC_REG_PORT4MODE_EN_OVWR) == 0x3) 11941 phy->flags |= FLAGS_4_PORT_MODE; 11942 else 11943 phy->flags &= ~FLAGS_4_PORT_MODE; 11944 /* Check Dual mode */ 11945 serdes_net_if = (REG_RD(bp, shmem_base + 11946 offsetof(struct shmem_region, dev_info. 11947 port_hw_config[port].default_cfg)) & 11948 PORT_HW_CFG_NET_SERDES_IF_MASK); 11949 /* Set the appropriate supported and flags indications per 11950 * interface type of the chip 11951 */ 11952 switch (serdes_net_if) { 11953 case PORT_HW_CFG_NET_SERDES_IF_SGMII: 11954 phy->supported &= (SUPPORTED_10baseT_Half | 11955 SUPPORTED_10baseT_Full | 11956 SUPPORTED_100baseT_Half | 11957 SUPPORTED_100baseT_Full | 11958 SUPPORTED_1000baseT_Full | 11959 SUPPORTED_FIBRE | 11960 SUPPORTED_Autoneg | 11961 SUPPORTED_Pause | 11962 SUPPORTED_Asym_Pause); 11963 phy->media_type = ETH_PHY_BASE_T; 11964 break; 11965 case PORT_HW_CFG_NET_SERDES_IF_XFI: 11966 phy->supported &= (SUPPORTED_1000baseT_Full | 11967 SUPPORTED_10000baseT_Full | 11968 SUPPORTED_FIBRE | 11969 SUPPORTED_Pause | 11970 SUPPORTED_Asym_Pause); 11971 phy->media_type = ETH_PHY_XFP_FIBER; 11972 break; 11973 case PORT_HW_CFG_NET_SERDES_IF_SFI: 11974 phy->supported &= (SUPPORTED_1000baseT_Full | 11975 SUPPORTED_10000baseT_Full | 11976 SUPPORTED_FIBRE | 11977 SUPPORTED_Pause | 11978 SUPPORTED_Asym_Pause); 11979 phy->media_type = ETH_PHY_SFPP_10G_FIBER; 11980 break; 11981 case PORT_HW_CFG_NET_SERDES_IF_KR: 11982 phy->media_type = ETH_PHY_KR; 11983 phy->supported &= (SUPPORTED_1000baseT_Full | 11984 SUPPORTED_10000baseT_Full | 11985 SUPPORTED_FIBRE | 11986 SUPPORTED_Autoneg | 11987 SUPPORTED_Pause | 11988 SUPPORTED_Asym_Pause); 11989 break; 11990 case PORT_HW_CFG_NET_SERDES_IF_DXGXS: 11991 phy->media_type = ETH_PHY_KR; 11992 phy->flags |= FLAGS_WC_DUAL_MODE; 11993 phy->supported &= (SUPPORTED_20000baseMLD2_Full | 11994 SUPPORTED_FIBRE | 11995 SUPPORTED_Pause | 11996 SUPPORTED_Asym_Pause); 11997 break; 11998 case PORT_HW_CFG_NET_SERDES_IF_KR2: 11999 phy->media_type = ETH_PHY_KR; 12000 phy->flags |= FLAGS_WC_DUAL_MODE; 12001 phy->supported &= (SUPPORTED_20000baseKR2_Full | 12002 SUPPORTED_10000baseT_Full | 12003 SUPPORTED_1000baseT_Full | 12004 SUPPORTED_Autoneg | 12005 SUPPORTED_FIBRE | 12006 SUPPORTED_Pause | 12007 SUPPORTED_Asym_Pause); 12008 phy->flags &= ~FLAGS_TX_ERROR_CHECK; 12009 break; 12010 default: 12011 DP(NETIF_MSG_LINK, "Unknown WC interface type 0x%x\n", 12012 serdes_net_if); 12013 break; 12014 } 12015 12016 /* Enable MDC/MDIO work-around for E3 A0 since free running MDC 12017 * was not set as expected. For B0, ECO will be enabled so there 12018 * won't be an issue there 12019 */ 12020 if (CHIP_REV(bp) == CHIP_REV_Ax) 12021 phy->flags |= FLAGS_MDC_MDIO_WA; 12022 else 12023 phy->flags |= FLAGS_MDC_MDIO_WA_B0; 12024 } else { 12025 switch (switch_cfg) { 12026 case SWITCH_CFG_1G: 12027 phy_addr = REG_RD(bp, 12028 NIG_REG_SERDES0_CTRL_PHY_ADDR + 12029 port * 0x10); 12030 *phy = phy_serdes; 12031 break; 12032 case SWITCH_CFG_10G: 12033 phy_addr = REG_RD(bp, 12034 NIG_REG_XGXS0_CTRL_PHY_ADDR + 12035 port * 0x18); 12036 *phy = phy_xgxs; 12037 break; 12038 default: 12039 DP(NETIF_MSG_LINK, "Invalid switch_cfg\n"); 12040 return -EINVAL; 12041 } 12042 } 12043 phy->addr = (u8)phy_addr; 12044 phy->mdio_ctrl = bnx2x_get_emac_base(bp, 12045 SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH, 12046 port); 12047 if (CHIP_IS_E2(bp)) 12048 phy->def_md_devad = E2_DEFAULT_PHY_DEV_ADDR; 12049 else 12050 phy->def_md_devad = DEFAULT_PHY_DEV_ADDR; 12051 12052 DP(NETIF_MSG_LINK, "Internal phy port=%d, addr=0x%x, mdio_ctl=0x%x\n", 12053 port, phy->addr, phy->mdio_ctrl); 12054 12055 bnx2x_populate_preemphasis(bp, shmem_base, phy, port, INT_PHY); 12056 return 0; 12057} 12058 12059static int bnx2x_populate_ext_phy(struct bnx2x *bp, 12060 u8 phy_index, 12061 u32 shmem_base, 12062 u32 shmem2_base, 12063 u8 port, 12064 struct bnx2x_phy *phy) 12065{ 12066 u32 ext_phy_config, phy_type, config2; 12067 u32 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH; 12068 ext_phy_config = bnx2x_get_ext_phy_config(bp, shmem_base, 12069 phy_index, port); 12070 phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config); 12071 /* Select the phy type */ 12072 switch (phy_type) { 12073 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: 12074 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_SWAPPED; 12075 *phy = phy_8073; 12076 break; 12077 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: 12078 *phy = phy_8705; 12079 break; 12080 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: 12081 *phy = phy_8706; 12082 break; 12083 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: 12084 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1; 12085 *phy = phy_8726; 12086 break; 12087 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC: 12088 /* BCM8727_NOC => BCM8727 no over current */ 12089 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1; 12090 *phy = phy_8727; 12091 phy->flags |= FLAGS_NOC; 12092 break; 12093 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722: 12094 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: 12095 mdc_mdio_access = SHARED_HW_CFG_MDC_MDIO_ACCESS1_EMAC1; 12096 *phy = phy_8727; 12097 break; 12098 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481: 12099 *phy = phy_8481; 12100 break; 12101 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: 12102 *phy = phy_84823; 12103 break; 12104 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833: 12105 *phy = phy_84833; 12106 break; 12107 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834: 12108 *phy = phy_84834; 12109 break; 12110 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54616: 12111 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE: 12112 *phy = phy_54618se; 12113 if (phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM54618SE) 12114 phy->flags |= FLAGS_EEE; 12115 break; 12116 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: 12117 *phy = phy_7101; 12118 break; 12119 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: 12120 *phy = phy_null; 12121 return -EINVAL; 12122 default: 12123 *phy = phy_null; 12124 /* In case external PHY wasn't found */ 12125 if ((phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && 12126 (phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)) 12127 return -EINVAL; 12128 return 0; 12129 } 12130 12131 phy->addr = XGXS_EXT_PHY_ADDR(ext_phy_config); 12132 bnx2x_populate_preemphasis(bp, shmem_base, phy, port, phy_index); 12133 12134 /* The shmem address of the phy version is located on different 12135 * structures. In case this structure is too old, do not set 12136 * the address 12137 */ 12138 config2 = REG_RD(bp, shmem_base + offsetof(struct shmem_region, 12139 dev_info.shared_hw_config.config2)); 12140 if (phy_index == EXT_PHY1) { 12141 phy->ver_addr = shmem_base + offsetof(struct shmem_region, 12142 port_mb[port].ext_phy_fw_version); 12143 12144 /* Check specific mdc mdio settings */ 12145 if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK) 12146 mdc_mdio_access = config2 & 12147 SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK; 12148 } else { 12149 u32 size = REG_RD(bp, shmem2_base); 12150 12151 if (size > 12152 offsetof(struct shmem2_region, ext_phy_fw_version2)) { 12153 phy->ver_addr = shmem2_base + 12154 offsetof(struct shmem2_region, 12155 ext_phy_fw_version2[port]); 12156 } 12157 /* Check specific mdc mdio settings */ 12158 if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK) 12159 mdc_mdio_access = (config2 & 12160 SHARED_HW_CFG_MDC_MDIO_ACCESS2_MASK) >> 12161 (SHARED_HW_CFG_MDC_MDIO_ACCESS2_SHIFT - 12162 SHARED_HW_CFG_MDC_MDIO_ACCESS1_SHIFT); 12163 } 12164 phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port); 12165 12166 if (((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) || 12167 (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834)) && 12168 (phy->ver_addr)) { 12169 /* Remove 100Mb link supported for BCM84833/4 when phy fw 12170 * version lower than or equal to 1.39 12171 */ 12172 u32 raw_ver = REG_RD(bp, phy->ver_addr); 12173 if (((raw_ver & 0x7F) <= 39) && 12174 (((raw_ver & 0xF80) >> 7) <= 1)) 12175 phy->supported &= ~(SUPPORTED_100baseT_Half | 12176 SUPPORTED_100baseT_Full); 12177 } 12178 12179 DP(NETIF_MSG_LINK, "phy_type 0x%x port %d found in index %d\n", 12180 phy_type, port, phy_index); 12181 DP(NETIF_MSG_LINK, " addr=0x%x, mdio_ctl=0x%x\n", 12182 phy->addr, phy->mdio_ctrl); 12183 return 0; 12184} 12185 12186static int bnx2x_populate_phy(struct bnx2x *bp, u8 phy_index, u32 shmem_base, 12187 u32 shmem2_base, u8 port, struct bnx2x_phy *phy) 12188{ 12189 int status = 0; 12190 phy->type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN; 12191 if (phy_index == INT_PHY) 12192 return bnx2x_populate_int_phy(bp, shmem_base, port, phy); 12193 status = bnx2x_populate_ext_phy(bp, phy_index, shmem_base, shmem2_base, 12194 port, phy); 12195 return status; 12196} 12197 12198static void bnx2x_phy_def_cfg(struct link_params *params, 12199 struct bnx2x_phy *phy, 12200 u8 phy_index) 12201{ 12202 struct bnx2x *bp = params->bp; 12203 u32 link_config; 12204 /* Populate the default phy configuration for MF mode */ 12205 if (phy_index == EXT_PHY2) { 12206 link_config = REG_RD(bp, params->shmem_base + 12207 offsetof(struct shmem_region, dev_info. 12208 port_feature_config[params->port].link_config2)); 12209 phy->speed_cap_mask = REG_RD(bp, params->shmem_base + 12210 offsetof(struct shmem_region, 12211 dev_info. 12212 port_hw_config[params->port].speed_capability_mask2)); 12213 } else { 12214 link_config = REG_RD(bp, params->shmem_base + 12215 offsetof(struct shmem_region, dev_info. 12216 port_feature_config[params->port].link_config)); 12217 phy->speed_cap_mask = REG_RD(bp, params->shmem_base + 12218 offsetof(struct shmem_region, 12219 dev_info. 12220 port_hw_config[params->port].speed_capability_mask)); 12221 } 12222 DP(NETIF_MSG_LINK, 12223 "Default config phy idx %x cfg 0x%x speed_cap_mask 0x%x\n", 12224 phy_index, link_config, phy->speed_cap_mask); 12225 12226 phy->req_duplex = DUPLEX_FULL; 12227 switch (link_config & PORT_FEATURE_LINK_SPEED_MASK) { 12228 case PORT_FEATURE_LINK_SPEED_10M_HALF: 12229 phy->req_duplex = DUPLEX_HALF; 12230 case PORT_FEATURE_LINK_SPEED_10M_FULL: 12231 phy->req_line_speed = SPEED_10; 12232 break; 12233 case PORT_FEATURE_LINK_SPEED_100M_HALF: 12234 phy->req_duplex = DUPLEX_HALF; 12235 case PORT_FEATURE_LINK_SPEED_100M_FULL: 12236 phy->req_line_speed = SPEED_100; 12237 break; 12238 case PORT_FEATURE_LINK_SPEED_1G: 12239 phy->req_line_speed = SPEED_1000; 12240 break; 12241 case PORT_FEATURE_LINK_SPEED_2_5G: 12242 phy->req_line_speed = SPEED_2500; 12243 break; 12244 case PORT_FEATURE_LINK_SPEED_10G_CX4: 12245 phy->req_line_speed = SPEED_10000; 12246 break; 12247 default: 12248 phy->req_line_speed = SPEED_AUTO_NEG; 12249 break; 12250 } 12251 12252 switch (link_config & PORT_FEATURE_FLOW_CONTROL_MASK) { 12253 case PORT_FEATURE_FLOW_CONTROL_AUTO: 12254 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_AUTO; 12255 break; 12256 case PORT_FEATURE_FLOW_CONTROL_TX: 12257 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_TX; 12258 break; 12259 case PORT_FEATURE_FLOW_CONTROL_RX: 12260 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_RX; 12261 break; 12262 case PORT_FEATURE_FLOW_CONTROL_BOTH: 12263 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_BOTH; 12264 break; 12265 default: 12266 phy->req_flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12267 break; 12268 } 12269} 12270 12271u32 bnx2x_phy_selection(struct link_params *params) 12272{ 12273 u32 phy_config_swapped, prio_cfg; 12274 u32 return_cfg = PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT; 12275 12276 phy_config_swapped = params->multi_phy_config & 12277 PORT_HW_CFG_PHY_SWAPPED_ENABLED; 12278 12279 prio_cfg = params->multi_phy_config & 12280 PORT_HW_CFG_PHY_SELECTION_MASK; 12281 12282 if (phy_config_swapped) { 12283 switch (prio_cfg) { 12284 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY: 12285 return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY; 12286 break; 12287 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY: 12288 return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY; 12289 break; 12290 case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY: 12291 return_cfg = PORT_HW_CFG_PHY_SELECTION_FIRST_PHY; 12292 break; 12293 case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY: 12294 return_cfg = PORT_HW_CFG_PHY_SELECTION_SECOND_PHY; 12295 break; 12296 } 12297 } else 12298 return_cfg = prio_cfg; 12299 12300 return return_cfg; 12301} 12302 12303int bnx2x_phy_probe(struct link_params *params) 12304{ 12305 u8 phy_index, actual_phy_idx; 12306 u32 phy_config_swapped, sync_offset, media_types; 12307 struct bnx2x *bp = params->bp; 12308 struct bnx2x_phy *phy; 12309 params->num_phys = 0; 12310 DP(NETIF_MSG_LINK, "Begin phy probe\n"); 12311 phy_config_swapped = params->multi_phy_config & 12312 PORT_HW_CFG_PHY_SWAPPED_ENABLED; 12313 12314 for (phy_index = INT_PHY; phy_index < MAX_PHYS; 12315 phy_index++) { 12316 actual_phy_idx = phy_index; 12317 if (phy_config_swapped) { 12318 if (phy_index == EXT_PHY1) 12319 actual_phy_idx = EXT_PHY2; 12320 else if (phy_index == EXT_PHY2) 12321 actual_phy_idx = EXT_PHY1; 12322 } 12323 DP(NETIF_MSG_LINK, "phy_config_swapped %x, phy_index %x," 12324 " actual_phy_idx %x\n", phy_config_swapped, 12325 phy_index, actual_phy_idx); 12326 phy = ¶ms->phy[actual_phy_idx]; 12327 if (bnx2x_populate_phy(bp, phy_index, params->shmem_base, 12328 params->shmem2_base, params->port, 12329 phy) != 0) { 12330 params->num_phys = 0; 12331 DP(NETIF_MSG_LINK, "phy probe failed in phy index %d\n", 12332 phy_index); 12333 for (phy_index = INT_PHY; 12334 phy_index < MAX_PHYS; 12335 phy_index++) 12336 *phy = phy_null; 12337 return -EINVAL; 12338 } 12339 if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN) 12340 break; 12341 12342 if (params->feature_config_flags & 12343 FEATURE_CONFIG_DISABLE_REMOTE_FAULT_DET) 12344 phy->flags &= ~FLAGS_TX_ERROR_CHECK; 12345 12346 if (!(params->feature_config_flags & 12347 FEATURE_CONFIG_MT_SUPPORT)) 12348 phy->flags |= FLAGS_MDC_MDIO_WA_G; 12349 12350 sync_offset = params->shmem_base + 12351 offsetof(struct shmem_region, 12352 dev_info.port_hw_config[params->port].media_type); 12353 media_types = REG_RD(bp, sync_offset); 12354 12355 /* Update media type for non-PMF sync only for the first time 12356 * In case the media type changes afterwards, it will be updated 12357 * using the update_status function 12358 */ 12359 if ((media_types & (PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK << 12360 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * 12361 actual_phy_idx))) == 0) { 12362 media_types |= ((phy->media_type & 12363 PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) << 12364 (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * 12365 actual_phy_idx)); 12366 } 12367 REG_WR(bp, sync_offset, media_types); 12368 12369 bnx2x_phy_def_cfg(params, phy, phy_index); 12370 params->num_phys++; 12371 } 12372 12373 DP(NETIF_MSG_LINK, "End phy probe. #phys found %x\n", params->num_phys); 12374 return 0; 12375} 12376 12377static void bnx2x_init_bmac_loopback(struct link_params *params, 12378 struct link_vars *vars) 12379{ 12380 struct bnx2x *bp = params->bp; 12381 vars->link_up = 1; 12382 vars->line_speed = SPEED_10000; 12383 vars->duplex = DUPLEX_FULL; 12384 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12385 vars->mac_type = MAC_TYPE_BMAC; 12386 12387 vars->phy_flags = PHY_XGXS_FLAG; 12388 12389 bnx2x_xgxs_deassert(params); 12390 12391 /* Set bmac loopback */ 12392 bnx2x_bmac_enable(params, vars, 1, 1); 12393 12394 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12395} 12396 12397static void bnx2x_init_emac_loopback(struct link_params *params, 12398 struct link_vars *vars) 12399{ 12400 struct bnx2x *bp = params->bp; 12401 vars->link_up = 1; 12402 vars->line_speed = SPEED_1000; 12403 vars->duplex = DUPLEX_FULL; 12404 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12405 vars->mac_type = MAC_TYPE_EMAC; 12406 12407 vars->phy_flags = PHY_XGXS_FLAG; 12408 12409 bnx2x_xgxs_deassert(params); 12410 /* Set bmac loopback */ 12411 bnx2x_emac_enable(params, vars, 1); 12412 bnx2x_emac_program(params, vars); 12413 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12414} 12415 12416static void bnx2x_init_xmac_loopback(struct link_params *params, 12417 struct link_vars *vars) 12418{ 12419 struct bnx2x *bp = params->bp; 12420 vars->link_up = 1; 12421 if (!params->req_line_speed[0]) 12422 vars->line_speed = SPEED_10000; 12423 else 12424 vars->line_speed = params->req_line_speed[0]; 12425 vars->duplex = DUPLEX_FULL; 12426 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12427 vars->mac_type = MAC_TYPE_XMAC; 12428 vars->phy_flags = PHY_XGXS_FLAG; 12429 /* Set WC to loopback mode since link is required to provide clock 12430 * to the XMAC in 20G mode 12431 */ 12432 bnx2x_set_aer_mmd(params, ¶ms->phy[0]); 12433 bnx2x_warpcore_reset_lane(bp, ¶ms->phy[0], 0); 12434 params->phy[INT_PHY].config_loopback( 12435 ¶ms->phy[INT_PHY], 12436 params); 12437 12438 bnx2x_xmac_enable(params, vars, 1); 12439 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12440} 12441 12442static void bnx2x_init_umac_loopback(struct link_params *params, 12443 struct link_vars *vars) 12444{ 12445 struct bnx2x *bp = params->bp; 12446 vars->link_up = 1; 12447 vars->line_speed = SPEED_1000; 12448 vars->duplex = DUPLEX_FULL; 12449 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12450 vars->mac_type = MAC_TYPE_UMAC; 12451 vars->phy_flags = PHY_XGXS_FLAG; 12452 bnx2x_umac_enable(params, vars, 1); 12453 12454 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12455} 12456 12457static void bnx2x_init_xgxs_loopback(struct link_params *params, 12458 struct link_vars *vars) 12459{ 12460 struct bnx2x *bp = params->bp; 12461 struct bnx2x_phy *int_phy = ¶ms->phy[INT_PHY]; 12462 vars->link_up = 1; 12463 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12464 vars->duplex = DUPLEX_FULL; 12465 if (params->req_line_speed[0] == SPEED_1000) 12466 vars->line_speed = SPEED_1000; 12467 else if ((params->req_line_speed[0] == SPEED_20000) || 12468 (int_phy->flags & FLAGS_WC_DUAL_MODE)) 12469 vars->line_speed = SPEED_20000; 12470 else 12471 vars->line_speed = SPEED_10000; 12472 12473 if (!USES_WARPCORE(bp)) 12474 bnx2x_xgxs_deassert(params); 12475 bnx2x_link_initialize(params, vars); 12476 12477 if (params->req_line_speed[0] == SPEED_1000) { 12478 if (USES_WARPCORE(bp)) 12479 bnx2x_umac_enable(params, vars, 0); 12480 else { 12481 bnx2x_emac_program(params, vars); 12482 bnx2x_emac_enable(params, vars, 0); 12483 } 12484 } else { 12485 if (USES_WARPCORE(bp)) 12486 bnx2x_xmac_enable(params, vars, 0); 12487 else 12488 bnx2x_bmac_enable(params, vars, 0, 1); 12489 } 12490 12491 if (params->loopback_mode == LOOPBACK_XGXS) { 12492 /* Set 10G XGXS loopback */ 12493 int_phy->config_loopback(int_phy, params); 12494 } else { 12495 /* Set external phy loopback */ 12496 u8 phy_index; 12497 for (phy_index = EXT_PHY1; 12498 phy_index < params->num_phys; phy_index++) 12499 if (params->phy[phy_index].config_loopback) 12500 params->phy[phy_index].config_loopback( 12501 ¶ms->phy[phy_index], 12502 params); 12503 } 12504 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12505 12506 bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed); 12507} 12508 12509void bnx2x_set_rx_filter(struct link_params *params, u8 en) 12510{ 12511 struct bnx2x *bp = params->bp; 12512 u8 val = en * 0x1F; 12513 12514 /* Open / close the gate between the NIG and the BRB */ 12515 if (!CHIP_IS_E1x(bp)) 12516 val |= en * 0x20; 12517 REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK + params->port*4, val); 12518 12519 if (!CHIP_IS_E1(bp)) { 12520 REG_WR(bp, NIG_REG_LLH0_BRB1_DRV_MASK_MF + params->port*4, 12521 en*0x3); 12522 } 12523 12524 REG_WR(bp, (params->port ? NIG_REG_LLH1_BRB1_NOT_MCP : 12525 NIG_REG_LLH0_BRB1_NOT_MCP), en); 12526} 12527static int bnx2x_avoid_link_flap(struct link_params *params, 12528 struct link_vars *vars) 12529{ 12530 u32 phy_idx; 12531 u32 dont_clear_stat, lfa_sts; 12532 struct bnx2x *bp = params->bp; 12533 12534 bnx2x_set_mdio_emac_per_phy(bp, params); 12535 /* Sync the link parameters */ 12536 bnx2x_link_status_update(params, vars); 12537 12538 /* 12539 * The module verification was already done by previous link owner, 12540 * so this call is meant only to get warning message 12541 */ 12542 12543 for (phy_idx = INT_PHY; phy_idx < params->num_phys; phy_idx++) { 12544 struct bnx2x_phy *phy = ¶ms->phy[phy_idx]; 12545 if (phy->phy_specific_func) { 12546 DP(NETIF_MSG_LINK, "Calling PHY specific func\n"); 12547 phy->phy_specific_func(phy, params, PHY_INIT); 12548 } 12549 if ((phy->media_type == ETH_PHY_SFPP_10G_FIBER) || 12550 (phy->media_type == ETH_PHY_SFP_1G_FIBER) || 12551 (phy->media_type == ETH_PHY_DA_TWINAX)) 12552 bnx2x_verify_sfp_module(phy, params); 12553 } 12554 lfa_sts = REG_RD(bp, params->lfa_base + 12555 offsetof(struct shmem_lfa, 12556 lfa_sts)); 12557 12558 dont_clear_stat = lfa_sts & SHMEM_LFA_DONT_CLEAR_STAT; 12559 12560 /* Re-enable the NIG/MAC */ 12561 if (CHIP_IS_E3(bp)) { 12562 if (!dont_clear_stat) { 12563 REG_WR(bp, GRCBASE_MISC + 12564 MISC_REGISTERS_RESET_REG_2_CLEAR, 12565 (MISC_REGISTERS_RESET_REG_2_MSTAT0 << 12566 params->port)); 12567 REG_WR(bp, GRCBASE_MISC + 12568 MISC_REGISTERS_RESET_REG_2_SET, 12569 (MISC_REGISTERS_RESET_REG_2_MSTAT0 << 12570 params->port)); 12571 } 12572 if (vars->line_speed < SPEED_10000) 12573 bnx2x_umac_enable(params, vars, 0); 12574 else 12575 bnx2x_xmac_enable(params, vars, 0); 12576 } else { 12577 if (vars->line_speed < SPEED_10000) 12578 bnx2x_emac_enable(params, vars, 0); 12579 else 12580 bnx2x_bmac_enable(params, vars, 0, !dont_clear_stat); 12581 } 12582 12583 /* Increment LFA count */ 12584 lfa_sts = ((lfa_sts & ~LINK_FLAP_AVOIDANCE_COUNT_MASK) | 12585 (((((lfa_sts & LINK_FLAP_AVOIDANCE_COUNT_MASK) >> 12586 LINK_FLAP_AVOIDANCE_COUNT_OFFSET) + 1) & 0xff) 12587 << LINK_FLAP_AVOIDANCE_COUNT_OFFSET)); 12588 /* Clear link flap reason */ 12589 lfa_sts &= ~LFA_LINK_FLAP_REASON_MASK; 12590 12591 REG_WR(bp, params->lfa_base + 12592 offsetof(struct shmem_lfa, lfa_sts), lfa_sts); 12593 12594 /* Disable NIG DRAIN */ 12595 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12596 12597 /* Enable interrupts */ 12598 bnx2x_link_int_enable(params); 12599 return 0; 12600} 12601 12602static void bnx2x_cannot_avoid_link_flap(struct link_params *params, 12603 struct link_vars *vars, 12604 int lfa_status) 12605{ 12606 u32 lfa_sts, cfg_idx, tmp_val; 12607 struct bnx2x *bp = params->bp; 12608 12609 bnx2x_link_reset(params, vars, 1); 12610 12611 if (!params->lfa_base) 12612 return; 12613 /* Store the new link parameters */ 12614 REG_WR(bp, params->lfa_base + 12615 offsetof(struct shmem_lfa, req_duplex), 12616 params->req_duplex[0] | (params->req_duplex[1] << 16)); 12617 12618 REG_WR(bp, params->lfa_base + 12619 offsetof(struct shmem_lfa, req_flow_ctrl), 12620 params->req_flow_ctrl[0] | (params->req_flow_ctrl[1] << 16)); 12621 12622 REG_WR(bp, params->lfa_base + 12623 offsetof(struct shmem_lfa, req_line_speed), 12624 params->req_line_speed[0] | (params->req_line_speed[1] << 16)); 12625 12626 for (cfg_idx = 0; cfg_idx < SHMEM_LINK_CONFIG_SIZE; cfg_idx++) { 12627 REG_WR(bp, params->lfa_base + 12628 offsetof(struct shmem_lfa, 12629 speed_cap_mask[cfg_idx]), 12630 params->speed_cap_mask[cfg_idx]); 12631 } 12632 12633 tmp_val = REG_RD(bp, params->lfa_base + 12634 offsetof(struct shmem_lfa, additional_config)); 12635 tmp_val &= ~REQ_FC_AUTO_ADV_MASK; 12636 tmp_val |= params->req_fc_auto_adv; 12637 12638 REG_WR(bp, params->lfa_base + 12639 offsetof(struct shmem_lfa, additional_config), tmp_val); 12640 12641 lfa_sts = REG_RD(bp, params->lfa_base + 12642 offsetof(struct shmem_lfa, lfa_sts)); 12643 12644 /* Clear the "Don't Clear Statistics" bit, and set reason */ 12645 lfa_sts &= ~SHMEM_LFA_DONT_CLEAR_STAT; 12646 12647 /* Set link flap reason */ 12648 lfa_sts &= ~LFA_LINK_FLAP_REASON_MASK; 12649 lfa_sts |= ((lfa_status & LFA_LINK_FLAP_REASON_MASK) << 12650 LFA_LINK_FLAP_REASON_OFFSET); 12651 12652 /* Increment link flap counter */ 12653 lfa_sts = ((lfa_sts & ~LINK_FLAP_COUNT_MASK) | 12654 (((((lfa_sts & LINK_FLAP_COUNT_MASK) >> 12655 LINK_FLAP_COUNT_OFFSET) + 1) & 0xff) 12656 << LINK_FLAP_COUNT_OFFSET)); 12657 REG_WR(bp, params->lfa_base + 12658 offsetof(struct shmem_lfa, lfa_sts), lfa_sts); 12659 /* Proceed with regular link initialization */ 12660} 12661 12662int bnx2x_phy_init(struct link_params *params, struct link_vars *vars) 12663{ 12664 int lfa_status; 12665 struct bnx2x *bp = params->bp; 12666 DP(NETIF_MSG_LINK, "Phy Initialization started\n"); 12667 DP(NETIF_MSG_LINK, "(1) req_speed %d, req_flowctrl %d\n", 12668 params->req_line_speed[0], params->req_flow_ctrl[0]); 12669 DP(NETIF_MSG_LINK, "(2) req_speed %d, req_flowctrl %d\n", 12670 params->req_line_speed[1], params->req_flow_ctrl[1]); 12671 DP(NETIF_MSG_LINK, "req_adv_flow_ctrl 0x%x\n", params->req_fc_auto_adv); 12672 vars->link_status = 0; 12673 vars->phy_link_up = 0; 12674 vars->link_up = 0; 12675 vars->line_speed = 0; 12676 vars->duplex = DUPLEX_FULL; 12677 vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; 12678 vars->mac_type = MAC_TYPE_NONE; 12679 vars->phy_flags = 0; 12680 vars->check_kr2_recovery_cnt = 0; 12681 params->link_flags = PHY_INITIALIZED; 12682 /* Driver opens NIG-BRB filters */ 12683 bnx2x_set_rx_filter(params, 1); 12684 bnx2x_chng_link_count(params, true); 12685 /* Check if link flap can be avoided */ 12686 lfa_status = bnx2x_check_lfa(params); 12687 12688 if (lfa_status == 0) { 12689 DP(NETIF_MSG_LINK, "Link Flap Avoidance in progress\n"); 12690 return bnx2x_avoid_link_flap(params, vars); 12691 } 12692 12693 DP(NETIF_MSG_LINK, "Cannot avoid link flap lfa_sta=0x%x\n", 12694 lfa_status); 12695 bnx2x_cannot_avoid_link_flap(params, vars, lfa_status); 12696 12697 /* Disable attentions */ 12698 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, 12699 (NIG_MASK_XGXS0_LINK_STATUS | 12700 NIG_MASK_XGXS0_LINK10G | 12701 NIG_MASK_SERDES0_LINK_STATUS | 12702 NIG_MASK_MI_INT)); 12703 12704 bnx2x_emac_init(params, vars); 12705 12706 if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) 12707 vars->link_status |= LINK_STATUS_PFC_ENABLED; 12708 12709 if (params->num_phys == 0) { 12710 DP(NETIF_MSG_LINK, "No phy found for initialization !!\n"); 12711 return -EINVAL; 12712 } 12713 set_phy_vars(params, vars); 12714 12715 DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys); 12716 switch (params->loopback_mode) { 12717 case LOOPBACK_BMAC: 12718 bnx2x_init_bmac_loopback(params, vars); 12719 break; 12720 case LOOPBACK_EMAC: 12721 bnx2x_init_emac_loopback(params, vars); 12722 break; 12723 case LOOPBACK_XMAC: 12724 bnx2x_init_xmac_loopback(params, vars); 12725 break; 12726 case LOOPBACK_UMAC: 12727 bnx2x_init_umac_loopback(params, vars); 12728 break; 12729 case LOOPBACK_XGXS: 12730 case LOOPBACK_EXT_PHY: 12731 bnx2x_init_xgxs_loopback(params, vars); 12732 break; 12733 default: 12734 if (!CHIP_IS_E3(bp)) { 12735 if (params->switch_cfg == SWITCH_CFG_10G) 12736 bnx2x_xgxs_deassert(params); 12737 else 12738 bnx2x_serdes_deassert(bp, params->port); 12739 } 12740 bnx2x_link_initialize(params, vars); 12741 msleep(30); 12742 bnx2x_link_int_enable(params); 12743 break; 12744 } 12745 bnx2x_update_mng(params, vars->link_status); 12746 12747 bnx2x_update_mng_eee(params, vars->eee_status); 12748 return 0; 12749} 12750 12751int bnx2x_link_reset(struct link_params *params, struct link_vars *vars, 12752 u8 reset_ext_phy) 12753{ 12754 struct bnx2x *bp = params->bp; 12755 u8 phy_index, port = params->port, clear_latch_ind = 0; 12756 DP(NETIF_MSG_LINK, "Resetting the link of port %d\n", port); 12757 /* Disable attentions */ 12758 vars->link_status = 0; 12759 bnx2x_chng_link_count(params, true); 12760 bnx2x_update_mng(params, vars->link_status); 12761 vars->eee_status &= ~(SHMEM_EEE_LP_ADV_STATUS_MASK | 12762 SHMEM_EEE_ACTIVE_BIT); 12763 bnx2x_update_mng_eee(params, vars->eee_status); 12764 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, 12765 (NIG_MASK_XGXS0_LINK_STATUS | 12766 NIG_MASK_XGXS0_LINK10G | 12767 NIG_MASK_SERDES0_LINK_STATUS | 12768 NIG_MASK_MI_INT)); 12769 12770 /* Activate nig drain */ 12771 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); 12772 12773 /* Disable nig egress interface */ 12774 if (!CHIP_IS_E3(bp)) { 12775 REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0); 12776 REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0); 12777 } 12778 12779 if (!CHIP_IS_E3(bp)) { 12780 bnx2x_set_bmac_rx(bp, params->chip_id, port, 0); 12781 } else { 12782 bnx2x_set_xmac_rxtx(params, 0); 12783 bnx2x_set_umac_rxtx(params, 0); 12784 } 12785 /* Disable emac */ 12786 if (!CHIP_IS_E3(bp)) 12787 REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); 12788 12789 usleep_range(10000, 20000); 12790 /* The PHY reset is controlled by GPIO 1 12791 * Hold it as vars low 12792 */ 12793 /* Clear link led */ 12794 bnx2x_set_mdio_emac_per_phy(bp, params); 12795 bnx2x_set_led(params, vars, LED_MODE_OFF, 0); 12796 12797 if (reset_ext_phy) { 12798 for (phy_index = EXT_PHY1; phy_index < params->num_phys; 12799 phy_index++) { 12800 if (params->phy[phy_index].link_reset) { 12801 bnx2x_set_aer_mmd(params, 12802 ¶ms->phy[phy_index]); 12803 params->phy[phy_index].link_reset( 12804 ¶ms->phy[phy_index], 12805 params); 12806 } 12807 if (params->phy[phy_index].flags & 12808 FLAGS_REARM_LATCH_SIGNAL) 12809 clear_latch_ind = 1; 12810 } 12811 } 12812 12813 if (clear_latch_ind) { 12814 /* Clear latching indication */ 12815 bnx2x_rearm_latch_signal(bp, port, 0); 12816 bnx2x_bits_dis(bp, NIG_REG_LATCH_BC_0 + port*4, 12817 1 << NIG_LATCH_BC_ENABLE_MI_INT); 12818 } 12819 if (params->phy[INT_PHY].link_reset) 12820 params->phy[INT_PHY].link_reset( 12821 ¶ms->phy[INT_PHY], params); 12822 12823 /* Disable nig ingress interface */ 12824 if (!CHIP_IS_E3(bp)) { 12825 /* Reset BigMac */ 12826 REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 12827 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); 12828 REG_WR(bp, NIG_REG_BMAC0_IN_EN + port*4, 0); 12829 REG_WR(bp, NIG_REG_EMAC0_IN_EN + port*4, 0); 12830 } else { 12831 u32 xmac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; 12832 bnx2x_set_xumac_nig(params, 0, 0); 12833 if (REG_RD(bp, MISC_REG_RESET_REG_2) & 12834 MISC_REGISTERS_RESET_REG_2_XMAC) 12835 REG_WR(bp, xmac_base + XMAC_REG_CTRL, 12836 XMAC_CTRL_REG_SOFT_RESET); 12837 } 12838 vars->link_up = 0; 12839 vars->phy_flags = 0; 12840 return 0; 12841} 12842int bnx2x_lfa_reset(struct link_params *params, 12843 struct link_vars *vars) 12844{ 12845 struct bnx2x *bp = params->bp; 12846 vars->link_up = 0; 12847 vars->phy_flags = 0; 12848 params->link_flags &= ~PHY_INITIALIZED; 12849 if (!params->lfa_base) 12850 return bnx2x_link_reset(params, vars, 1); 12851 /* 12852 * Activate NIG drain so that during this time the device won't send 12853 * anything while it is unable to response. 12854 */ 12855 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 1); 12856 12857 /* 12858 * Close gracefully the gate from BMAC to NIG such that no half packets 12859 * are passed. 12860 */ 12861 if (!CHIP_IS_E3(bp)) 12862 bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 0); 12863 12864 if (CHIP_IS_E3(bp)) { 12865 bnx2x_set_xmac_rxtx(params, 0); 12866 bnx2x_set_umac_rxtx(params, 0); 12867 } 12868 /* Wait 10ms for the pipe to clean up*/ 12869 usleep_range(10000, 20000); 12870 12871 /* Clean the NIG-BRB using the network filters in a way that will 12872 * not cut a packet in the middle. 12873 */ 12874 bnx2x_set_rx_filter(params, 0); 12875 12876 /* 12877 * Re-open the gate between the BMAC and the NIG, after verifying the 12878 * gate to the BRB is closed, otherwise packets may arrive to the 12879 * firmware before driver had initialized it. The target is to achieve 12880 * minimum management protocol down time. 12881 */ 12882 if (!CHIP_IS_E3(bp)) 12883 bnx2x_set_bmac_rx(bp, params->chip_id, params->port, 1); 12884 12885 if (CHIP_IS_E3(bp)) { 12886 bnx2x_set_xmac_rxtx(params, 1); 12887 bnx2x_set_umac_rxtx(params, 1); 12888 } 12889 /* Disable NIG drain */ 12890 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 12891 return 0; 12892} 12893 12894/****************************************************************************/ 12895/* Common function */ 12896/****************************************************************************/ 12897static int bnx2x_8073_common_init_phy(struct bnx2x *bp, 12898 u32 shmem_base_path[], 12899 u32 shmem2_base_path[], u8 phy_index, 12900 u32 chip_id) 12901{ 12902 struct bnx2x_phy phy[PORT_MAX]; 12903 struct bnx2x_phy *phy_blk[PORT_MAX]; 12904 u16 val; 12905 s8 port = 0; 12906 s8 port_of_path = 0; 12907 u32 swap_val, swap_override; 12908 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); 12909 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); 12910 port ^= (swap_val && swap_override); 12911 bnx2x_ext_phy_hw_reset(bp, port); 12912 /* PART1 - Reset both phys */ 12913 for (port = PORT_MAX - 1; port >= PORT_0; port--) { 12914 u32 shmem_base, shmem2_base; 12915 /* In E2, same phy is using for port0 of the two paths */ 12916 if (CHIP_IS_E1x(bp)) { 12917 shmem_base = shmem_base_path[0]; 12918 shmem2_base = shmem2_base_path[0]; 12919 port_of_path = port; 12920 } else { 12921 shmem_base = shmem_base_path[port]; 12922 shmem2_base = shmem2_base_path[port]; 12923 port_of_path = 0; 12924 } 12925 12926 /* Extract the ext phy address for the port */ 12927 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base, 12928 port_of_path, &phy[port]) != 12929 0) { 12930 DP(NETIF_MSG_LINK, "populate_phy failed\n"); 12931 return -EINVAL; 12932 } 12933 /* Disable attentions */ 12934 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + 12935 port_of_path*4, 12936 (NIG_MASK_XGXS0_LINK_STATUS | 12937 NIG_MASK_XGXS0_LINK10G | 12938 NIG_MASK_SERDES0_LINK_STATUS | 12939 NIG_MASK_MI_INT)); 12940 12941 /* Need to take the phy out of low power mode in order 12942 * to write to access its registers 12943 */ 12944 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 12945 MISC_REGISTERS_GPIO_OUTPUT_HIGH, 12946 port); 12947 12948 /* Reset the phy */ 12949 bnx2x_cl45_write(bp, &phy[port], 12950 MDIO_PMA_DEVAD, 12951 MDIO_PMA_REG_CTRL, 12952 1<<15); 12953 } 12954 12955 /* Add delay of 150ms after reset */ 12956 msleep(150); 12957 12958 if (phy[PORT_0].addr & 0x1) { 12959 phy_blk[PORT_0] = &(phy[PORT_1]); 12960 phy_blk[PORT_1] = &(phy[PORT_0]); 12961 } else { 12962 phy_blk[PORT_0] = &(phy[PORT_0]); 12963 phy_blk[PORT_1] = &(phy[PORT_1]); 12964 } 12965 12966 /* PART2 - Download firmware to both phys */ 12967 for (port = PORT_MAX - 1; port >= PORT_0; port--) { 12968 if (CHIP_IS_E1x(bp)) 12969 port_of_path = port; 12970 else 12971 port_of_path = 0; 12972 12973 DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n", 12974 phy_blk[port]->addr); 12975 if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port], 12976 port_of_path)) 12977 return -EINVAL; 12978 12979 /* Only set bit 10 = 1 (Tx power down) */ 12980 bnx2x_cl45_read(bp, phy_blk[port], 12981 MDIO_PMA_DEVAD, 12982 MDIO_PMA_REG_TX_POWER_DOWN, &val); 12983 12984 /* Phase1 of TX_POWER_DOWN reset */ 12985 bnx2x_cl45_write(bp, phy_blk[port], 12986 MDIO_PMA_DEVAD, 12987 MDIO_PMA_REG_TX_POWER_DOWN, 12988 (val | 1<<10)); 12989 } 12990 12991 /* Toggle Transmitter: Power down and then up with 600ms delay 12992 * between 12993 */ 12994 msleep(600); 12995 12996 /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */ 12997 for (port = PORT_MAX - 1; port >= PORT_0; port--) { 12998 /* Phase2 of POWER_DOWN_RESET */ 12999 /* Release bit 10 (Release Tx power down) */ 13000 bnx2x_cl45_read(bp, phy_blk[port], 13001 MDIO_PMA_DEVAD, 13002 MDIO_PMA_REG_TX_POWER_DOWN, &val); 13003 13004 bnx2x_cl45_write(bp, phy_blk[port], 13005 MDIO_PMA_DEVAD, 13006 MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); 13007 usleep_range(15000, 30000); 13008 13009 /* Read modify write the SPI-ROM version select register */ 13010 bnx2x_cl45_read(bp, phy_blk[port], 13011 MDIO_PMA_DEVAD, 13012 MDIO_PMA_REG_EDC_FFE_MAIN, &val); 13013 bnx2x_cl45_write(bp, phy_blk[port], 13014 MDIO_PMA_DEVAD, 13015 MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); 13016 13017 /* set GPIO2 back to LOW */ 13018 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, 13019 MISC_REGISTERS_GPIO_OUTPUT_LOW, port); 13020 } 13021 return 0; 13022} 13023static int bnx2x_8726_common_init_phy(struct bnx2x *bp, 13024 u32 shmem_base_path[], 13025 u32 shmem2_base_path[], u8 phy_index, 13026 u32 chip_id) 13027{ 13028 u32 val; 13029 s8 port; 13030 struct bnx2x_phy phy; 13031 /* Use port1 because of the static port-swap */ 13032 /* Enable the module detection interrupt */ 13033 val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN); 13034 val |= ((1<<MISC_REGISTERS_GPIO_3)| 13035 (1<<(MISC_REGISTERS_GPIO_3 + MISC_REGISTERS_GPIO_PORT_SHIFT))); 13036 REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val); 13037 13038 bnx2x_ext_phy_hw_reset(bp, 0); 13039 usleep_range(5000, 10000); 13040 for (port = 0; port < PORT_MAX; port++) { 13041 u32 shmem_base, shmem2_base; 13042 13043 /* In E2, same phy is using for port0 of the two paths */ 13044 if (CHIP_IS_E1x(bp)) { 13045 shmem_base = shmem_base_path[0]; 13046 shmem2_base = shmem2_base_path[0]; 13047 } else { 13048 shmem_base = shmem_base_path[port]; 13049 shmem2_base = shmem2_base_path[port]; 13050 } 13051 /* Extract the ext phy address for the port */ 13052 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base, 13053 port, &phy) != 13054 0) { 13055 DP(NETIF_MSG_LINK, "populate phy failed\n"); 13056 return -EINVAL; 13057 } 13058 13059 /* Reset phy*/ 13060 bnx2x_cl45_write(bp, &phy, 13061 MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x0001); 13062 13063 13064 /* Set fault module detected LED on */ 13065 bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, 13066 MISC_REGISTERS_GPIO_HIGH, 13067 port); 13068 } 13069 13070 return 0; 13071} 13072static void bnx2x_get_ext_phy_reset_gpio(struct bnx2x *bp, u32 shmem_base, 13073 u8 *io_gpio, u8 *io_port) 13074{ 13075 13076 u32 phy_gpio_reset = REG_RD(bp, shmem_base + 13077 offsetof(struct shmem_region, 13078 dev_info.port_hw_config[PORT_0].default_cfg)); 13079 switch (phy_gpio_reset) { 13080 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0: 13081 *io_gpio = 0; 13082 *io_port = 0; 13083 break; 13084 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P0: 13085 *io_gpio = 1; 13086 *io_port = 0; 13087 break; 13088 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P0: 13089 *io_gpio = 2; 13090 *io_port = 0; 13091 break; 13092 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P0: 13093 *io_gpio = 3; 13094 *io_port = 0; 13095 break; 13096 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P1: 13097 *io_gpio = 0; 13098 *io_port = 1; 13099 break; 13100 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P1: 13101 *io_gpio = 1; 13102 *io_port = 1; 13103 break; 13104 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P1: 13105 *io_gpio = 2; 13106 *io_port = 1; 13107 break; 13108 case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P1: 13109 *io_gpio = 3; 13110 *io_port = 1; 13111 break; 13112 default: 13113 /* Don't override the io_gpio and io_port */ 13114 break; 13115 } 13116} 13117 13118static int bnx2x_8727_common_init_phy(struct bnx2x *bp, 13119 u32 shmem_base_path[], 13120 u32 shmem2_base_path[], u8 phy_index, 13121 u32 chip_id) 13122{ 13123 s8 port, reset_gpio; 13124 u32 swap_val, swap_override; 13125 struct bnx2x_phy phy[PORT_MAX]; 13126 struct bnx2x_phy *phy_blk[PORT_MAX]; 13127 s8 port_of_path; 13128 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); 13129 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); 13130 13131 reset_gpio = MISC_REGISTERS_GPIO_1; 13132 port = 1; 13133 13134 /* Retrieve the reset gpio/port which control the reset. 13135 * Default is GPIO1, PORT1 13136 */ 13137 bnx2x_get_ext_phy_reset_gpio(bp, shmem_base_path[0], 13138 (u8 *)&reset_gpio, (u8 *)&port); 13139 13140 /* Calculate the port based on port swap */ 13141 port ^= (swap_val && swap_override); 13142 13143 /* Initiate PHY reset*/ 13144 bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_LOW, 13145 port); 13146 usleep_range(1000, 2000); 13147 bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_HIGH, 13148 port); 13149 13150 usleep_range(5000, 10000); 13151 13152 /* PART1 - Reset both phys */ 13153 for (port = PORT_MAX - 1; port >= PORT_0; port--) { 13154 u32 shmem_base, shmem2_base; 13155 13156 /* In E2, same phy is using for port0 of the two paths */ 13157 if (CHIP_IS_E1x(bp)) { 13158 shmem_base = shmem_base_path[0]; 13159 shmem2_base = shmem2_base_path[0]; 13160 port_of_path = port; 13161 } else { 13162 shmem_base = shmem_base_path[port]; 13163 shmem2_base = shmem2_base_path[port]; 13164 port_of_path = 0; 13165 } 13166 13167 /* Extract the ext phy address for the port */ 13168 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base, 13169 port_of_path, &phy[port]) != 13170 0) { 13171 DP(NETIF_MSG_LINK, "populate phy failed\n"); 13172 return -EINVAL; 13173 } 13174 /* disable attentions */ 13175 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + 13176 port_of_path*4, 13177 (NIG_MASK_XGXS0_LINK_STATUS | 13178 NIG_MASK_XGXS0_LINK10G | 13179 NIG_MASK_SERDES0_LINK_STATUS | 13180 NIG_MASK_MI_INT)); 13181 13182 13183 /* Reset the phy */ 13184 bnx2x_cl45_write(bp, &phy[port], 13185 MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); 13186 } 13187 13188 /* Add delay of 150ms after reset */ 13189 msleep(150); 13190 if (phy[PORT_0].addr & 0x1) { 13191 phy_blk[PORT_0] = &(phy[PORT_1]); 13192 phy_blk[PORT_1] = &(phy[PORT_0]); 13193 } else { 13194 phy_blk[PORT_0] = &(phy[PORT_0]); 13195 phy_blk[PORT_1] = &(phy[PORT_1]); 13196 } 13197 /* PART2 - Download firmware to both phys */ 13198 for (port = PORT_MAX - 1; port >= PORT_0; port--) { 13199 if (CHIP_IS_E1x(bp)) 13200 port_of_path = port; 13201 else 13202 port_of_path = 0; 13203 DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n", 13204 phy_blk[port]->addr); 13205 if (bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port], 13206 port_of_path)) 13207 return -EINVAL; 13208 /* Disable PHY transmitter output */ 13209 bnx2x_cl45_write(bp, phy_blk[port], 13210 MDIO_PMA_DEVAD, 13211 MDIO_PMA_REG_TX_DISABLE, 1); 13212 13213 } 13214 return 0; 13215} 13216 13217static int bnx2x_84833_common_init_phy(struct bnx2x *bp, 13218 u32 shmem_base_path[], 13219 u32 shmem2_base_path[], 13220 u8 phy_index, 13221 u32 chip_id) 13222{ 13223 u8 reset_gpios; 13224 reset_gpios = bnx2x_84833_get_reset_gpios(bp, shmem_base_path, chip_id); 13225 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_LOW); 13226 udelay(10); 13227 bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_HIGH); 13228 DP(NETIF_MSG_LINK, "84833 reset pulse on pin values 0x%x\n", 13229 reset_gpios); 13230 return 0; 13231} 13232 13233static int bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[], 13234 u32 shmem2_base_path[], u8 phy_index, 13235 u32 ext_phy_type, u32 chip_id) 13236{ 13237 int rc = 0; 13238 13239 switch (ext_phy_type) { 13240 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: 13241 rc = bnx2x_8073_common_init_phy(bp, shmem_base_path, 13242 shmem2_base_path, 13243 phy_index, chip_id); 13244 break; 13245 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8722: 13246 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727: 13247 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC: 13248 rc = bnx2x_8727_common_init_phy(bp, shmem_base_path, 13249 shmem2_base_path, 13250 phy_index, chip_id); 13251 break; 13252 13253 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: 13254 /* GPIO1 affects both ports, so there's need to pull 13255 * it for single port alone 13256 */ 13257 rc = bnx2x_8726_common_init_phy(bp, shmem_base_path, 13258 shmem2_base_path, 13259 phy_index, chip_id); 13260 break; 13261 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833: 13262 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84834: 13263 /* GPIO3's are linked, and so both need to be toggled 13264 * to obtain required 2us pulse. 13265 */ 13266 rc = bnx2x_84833_common_init_phy(bp, shmem_base_path, 13267 shmem2_base_path, 13268 phy_index, chip_id); 13269 break; 13270 case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: 13271 rc = -EINVAL; 13272 break; 13273 default: 13274 DP(NETIF_MSG_LINK, 13275 "ext_phy 0x%x common init not required\n", 13276 ext_phy_type); 13277 break; 13278 } 13279 13280 if (rc) 13281 netdev_err(bp->dev, "Warning: PHY was not initialized," 13282 " Port %d\n", 13283 0); 13284 return rc; 13285} 13286 13287int bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[], 13288 u32 shmem2_base_path[], u32 chip_id) 13289{ 13290 int rc = 0; 13291 u32 phy_ver, val; 13292 u8 phy_index = 0; 13293 u32 ext_phy_type, ext_phy_config; 13294 13295 bnx2x_set_mdio_clk(bp, chip_id, GRCBASE_EMAC0); 13296 bnx2x_set_mdio_clk(bp, chip_id, GRCBASE_EMAC1); 13297 DP(NETIF_MSG_LINK, "Begin common phy init\n"); 13298 if (CHIP_IS_E3(bp)) { 13299 /* Enable EPIO */ 13300 val = REG_RD(bp, MISC_REG_GEN_PURP_HWG); 13301 REG_WR(bp, MISC_REG_GEN_PURP_HWG, val | 1); 13302 } 13303 /* Check if common init was already done */ 13304 phy_ver = REG_RD(bp, shmem_base_path[0] + 13305 offsetof(struct shmem_region, 13306 port_mb[PORT_0].ext_phy_fw_version)); 13307 if (phy_ver) { 13308 DP(NETIF_MSG_LINK, "Not doing common init; phy ver is 0x%x\n", 13309 phy_ver); 13310 return 0; 13311 } 13312 13313 /* Read the ext_phy_type for arbitrary port(0) */ 13314 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS; 13315 phy_index++) { 13316 ext_phy_config = bnx2x_get_ext_phy_config(bp, 13317 shmem_base_path[0], 13318 phy_index, 0); 13319 ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config); 13320 rc |= bnx2x_ext_phy_common_init(bp, shmem_base_path, 13321 shmem2_base_path, 13322 phy_index, ext_phy_type, 13323 chip_id); 13324 } 13325 return rc; 13326} 13327 13328static void bnx2x_check_over_curr(struct link_params *params, 13329 struct link_vars *vars) 13330{ 13331 struct bnx2x *bp = params->bp; 13332 u32 cfg_pin; 13333 u8 port = params->port; 13334 u32 pin_val; 13335 13336 cfg_pin = (REG_RD(bp, params->shmem_base + 13337 offsetof(struct shmem_region, 13338 dev_info.port_hw_config[port].e3_cmn_pin_cfg1)) & 13339 PORT_HW_CFG_E3_OVER_CURRENT_MASK) >> 13340 PORT_HW_CFG_E3_OVER_CURRENT_SHIFT; 13341 13342 /* Ignore check if no external input PIN available */ 13343 if (bnx2x_get_cfg_pin(bp, cfg_pin, &pin_val) != 0) 13344 return; 13345 13346 if (!pin_val) { 13347 if ((vars->phy_flags & PHY_OVER_CURRENT_FLAG) == 0) { 13348 netdev_err(bp->dev, "Error: Power fault on Port %d has" 13349 " been detected and the power to " 13350 "that SFP+ module has been removed" 13351 " to prevent failure of the card." 13352 " Please remove the SFP+ module and" 13353 " restart the system to clear this" 13354 " error.\n", 13355 params->port); 13356 vars->phy_flags |= PHY_OVER_CURRENT_FLAG; 13357 bnx2x_warpcore_power_module(params, 0); 13358 } 13359 } else 13360 vars->phy_flags &= ~PHY_OVER_CURRENT_FLAG; 13361} 13362 13363/* Returns 0 if no change occurred since last check; 1 otherwise. */ 13364static u8 bnx2x_analyze_link_error(struct link_params *params, 13365 struct link_vars *vars, u32 status, 13366 u32 phy_flag, u32 link_flag, u8 notify) 13367{ 13368 struct bnx2x *bp = params->bp; 13369 /* Compare new value with previous value */ 13370 u8 led_mode; 13371 u32 old_status = (vars->phy_flags & phy_flag) ? 1 : 0; 13372 13373 if ((status ^ old_status) == 0) 13374 return 0; 13375 13376 /* If values differ */ 13377 switch (phy_flag) { 13378 case PHY_HALF_OPEN_CONN_FLAG: 13379 DP(NETIF_MSG_LINK, "Analyze Remote Fault\n"); 13380 break; 13381 case PHY_SFP_TX_FAULT_FLAG: 13382 DP(NETIF_MSG_LINK, "Analyze TX Fault\n"); 13383 break; 13384 default: 13385 DP(NETIF_MSG_LINK, "Analyze UNKNOWN\n"); 13386 } 13387 DP(NETIF_MSG_LINK, "Link changed:[%x %x]->%x\n", vars->link_up, 13388 old_status, status); 13389 13390 /* Do not touch the link in case physical link down */ 13391 if ((vars->phy_flags & PHY_PHYSICAL_LINK_FLAG) == 0) 13392 return 1; 13393 13394 /* a. Update shmem->link_status accordingly 13395 * b. Update link_vars->link_up 13396 */ 13397 if (status) { 13398 vars->link_status &= ~LINK_STATUS_LINK_UP; 13399 vars->link_status |= link_flag; 13400 vars->link_up = 0; 13401 vars->phy_flags |= phy_flag; 13402 13403 /* activate nig drain */ 13404 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 1); 13405 /* Set LED mode to off since the PHY doesn't know about these 13406 * errors 13407 */ 13408 led_mode = LED_MODE_OFF; 13409 } else { 13410 vars->link_status |= LINK_STATUS_LINK_UP; 13411 vars->link_status &= ~link_flag; 13412 vars->link_up = 1; 13413 vars->phy_flags &= ~phy_flag; 13414 led_mode = LED_MODE_OPER; 13415 13416 /* Clear nig drain */ 13417 REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); 13418 } 13419 bnx2x_sync_link(params, vars); 13420 /* Update the LED according to the link state */ 13421 bnx2x_set_led(params, vars, led_mode, SPEED_10000); 13422 13423 /* Update link status in the shared memory */ 13424 bnx2x_update_mng(params, vars->link_status); 13425 13426 /* C. Trigger General Attention */ 13427 vars->periodic_flags |= PERIODIC_FLAGS_LINK_EVENT; 13428 if (notify) 13429 bnx2x_notify_link_changed(bp); 13430 13431 return 1; 13432} 13433 13434/****************************************************************************** 13435* Description: 13436* This function checks for half opened connection change indication. 13437* When such change occurs, it calls the bnx2x_analyze_link_error 13438* to check if Remote Fault is set or cleared. Reception of remote fault 13439* status message in the MAC indicates that the peer's MAC has detected 13440* a fault, for example, due to break in the TX side of fiber. 13441* 13442******************************************************************************/ 13443static int bnx2x_check_half_open_conn(struct link_params *params, 13444 struct link_vars *vars, 13445 u8 notify) 13446{ 13447 struct bnx2x *bp = params->bp; 13448 u32 lss_status = 0; 13449 u32 mac_base; 13450 /* In case link status is physically up @ 10G do */ 13451 if (((vars->phy_flags & PHY_PHYSICAL_LINK_FLAG) == 0) || 13452 (REG_RD(bp, NIG_REG_EGRESS_EMAC0_PORT + params->port*4))) 13453 return 0; 13454 13455 if (CHIP_IS_E3(bp) && 13456 (REG_RD(bp, MISC_REG_RESET_REG_2) & 13457 (MISC_REGISTERS_RESET_REG_2_XMAC))) { 13458 /* Check E3 XMAC */ 13459 /* Note that link speed cannot be queried here, since it may be 13460 * zero while link is down. In case UMAC is active, LSS will 13461 * simply not be set 13462 */ 13463 mac_base = (params->port) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; 13464 13465 /* Clear stick bits (Requires rising edge) */ 13466 REG_WR(bp, mac_base + XMAC_REG_CLEAR_RX_LSS_STATUS, 0); 13467 REG_WR(bp, mac_base + XMAC_REG_CLEAR_RX_LSS_STATUS, 13468 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_LOCAL_FAULT_STATUS | 13469 XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_REMOTE_FAULT_STATUS); 13470 if (REG_RD(bp, mac_base + XMAC_REG_RX_LSS_STATUS)) 13471 lss_status = 1; 13472 13473 bnx2x_analyze_link_error(params, vars, lss_status, 13474 PHY_HALF_OPEN_CONN_FLAG, 13475 LINK_STATUS_NONE, notify); 13476 } else if (REG_RD(bp, MISC_REG_RESET_REG_2) & 13477 (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port)) { 13478 /* Check E1X / E2 BMAC */ 13479 u32 lss_status_reg; 13480 u32 wb_data[2]; 13481 mac_base = params->port ? NIG_REG_INGRESS_BMAC1_MEM : 13482 NIG_REG_INGRESS_BMAC0_MEM; 13483 /* Read BIGMAC_REGISTER_RX_LSS_STATUS */ 13484 if (CHIP_IS_E2(bp)) 13485 lss_status_reg = BIGMAC2_REGISTER_RX_LSS_STAT; 13486 else 13487 lss_status_reg = BIGMAC_REGISTER_RX_LSS_STATUS; 13488 13489 REG_RD_DMAE(bp, mac_base + lss_status_reg, wb_data, 2); 13490 lss_status = (wb_data[0] > 0); 13491 13492 bnx2x_analyze_link_error(params, vars, lss_status, 13493 PHY_HALF_OPEN_CONN_FLAG, 13494 LINK_STATUS_NONE, notify); 13495 } 13496 return 0; 13497} 13498static void bnx2x_sfp_tx_fault_detection(struct bnx2x_phy *phy, 13499 struct link_params *params, 13500 struct link_vars *vars) 13501{ 13502 struct bnx2x *bp = params->bp; 13503 u32 cfg_pin, value = 0; 13504 u8 led_change, port = params->port; 13505 13506 /* Get The SFP+ TX_Fault controlling pin ([eg]pio) */ 13507 cfg_pin = (REG_RD(bp, params->shmem_base + offsetof(struct shmem_region, 13508 dev_info.port_hw_config[port].e3_cmn_pin_cfg)) & 13509 PORT_HW_CFG_E3_TX_FAULT_MASK) >> 13510 PORT_HW_CFG_E3_TX_FAULT_SHIFT; 13511 13512 if (bnx2x_get_cfg_pin(bp, cfg_pin, &value)) { 13513 DP(NETIF_MSG_LINK, "Failed to read pin 0x%02x\n", cfg_pin); 13514 return; 13515 } 13516 13517 led_change = bnx2x_analyze_link_error(params, vars, value, 13518 PHY_SFP_TX_FAULT_FLAG, 13519 LINK_STATUS_SFP_TX_FAULT, 1); 13520 13521 if (led_change) { 13522 /* Change TX_Fault led, set link status for further syncs */ 13523 u8 led_mode; 13524 13525 if (vars->phy_flags & PHY_SFP_TX_FAULT_FLAG) { 13526 led_mode = MISC_REGISTERS_GPIO_HIGH; 13527 vars->link_status |= LINK_STATUS_SFP_TX_FAULT; 13528 } else { 13529 led_mode = MISC_REGISTERS_GPIO_LOW; 13530 vars->link_status &= ~LINK_STATUS_SFP_TX_FAULT; 13531 } 13532 13533 /* If module is unapproved, led should be on regardless */ 13534 if (!(phy->flags & FLAGS_SFP_NOT_APPROVED)) { 13535 DP(NETIF_MSG_LINK, "Change TX_Fault LED: ->%x\n", 13536 led_mode); 13537 bnx2x_set_e3_module_fault_led(params, led_mode); 13538 } 13539 } 13540} 13541static void bnx2x_kr2_recovery(struct link_params *params, 13542 struct link_vars *vars, 13543 struct bnx2x_phy *phy) 13544{ 13545 struct bnx2x *bp = params->bp; 13546 DP(NETIF_MSG_LINK, "KR2 recovery\n"); 13547 bnx2x_warpcore_enable_AN_KR2(phy, params, vars); 13548 bnx2x_warpcore_restart_AN_KR(phy, params); 13549} 13550 13551static void bnx2x_check_kr2_wa(struct link_params *params, 13552 struct link_vars *vars, 13553 struct bnx2x_phy *phy) 13554{ 13555 struct bnx2x *bp = params->bp; 13556 u16 base_page, next_page, not_kr2_device, lane; 13557 int sigdet; 13558 13559 /* Once KR2 was disabled, wait 5 seconds before checking KR2 recovery 13560 * Since some switches tend to reinit the AN process and clear the 13561 * the advertised BP/NP after ~2 seconds causing the KR2 to be disabled 13562 * and recovered many times 13563 */ 13564 if (vars->check_kr2_recovery_cnt > 0) { 13565 vars->check_kr2_recovery_cnt--; 13566 return; 13567 } 13568 13569 sigdet = bnx2x_warpcore_get_sigdet(phy, params); 13570 if (!sigdet) { 13571 if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { 13572 bnx2x_kr2_recovery(params, vars, phy); 13573 DP(NETIF_MSG_LINK, "No sigdet\n"); 13574 } 13575 return; 13576 } 13577 13578 lane = bnx2x_get_warpcore_lane(phy, params); 13579 CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, 13580 MDIO_AER_BLOCK_AER_REG, lane); 13581 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 13582 MDIO_AN_REG_LP_AUTO_NEG, &base_page); 13583 bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 13584 MDIO_AN_REG_LP_AUTO_NEG2, &next_page); 13585 bnx2x_set_aer_mmd(params, phy); 13586 13587 /* CL73 has not begun yet */ 13588 if (base_page == 0) { 13589 if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { 13590 bnx2x_kr2_recovery(params, vars, phy); 13591 DP(NETIF_MSG_LINK, "No BP\n"); 13592 } 13593 return; 13594 } 13595 13596 /* In case NP bit is not set in the BasePage, or it is set, 13597 * but only KX is advertised, declare this link partner as non-KR2 13598 * device. 13599 */ 13600 not_kr2_device = (((base_page & 0x8000) == 0) || 13601 (((base_page & 0x8000) && 13602 ((next_page & 0xe0) == 0x20)))); 13603 13604 /* In case KR2 is already disabled, check if we need to re-enable it */ 13605 if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { 13606 if (!not_kr2_device) { 13607 DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page, 13608 next_page); 13609 bnx2x_kr2_recovery(params, vars, phy); 13610 } 13611 return; 13612 } 13613 /* KR2 is enabled, but not KR2 device */ 13614 if (not_kr2_device) { 13615 /* Disable KR2 on both lanes */ 13616 DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page, next_page); 13617 bnx2x_disable_kr2(params, vars, phy); 13618 /* Restart AN on leading lane */ 13619 bnx2x_warpcore_restart_AN_KR(phy, params); 13620 return; 13621 } 13622} 13623 13624void bnx2x_period_func(struct link_params *params, struct link_vars *vars) 13625{ 13626 u16 phy_idx; 13627 struct bnx2x *bp = params->bp; 13628 for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) { 13629 if (params->phy[phy_idx].flags & FLAGS_TX_ERROR_CHECK) { 13630 bnx2x_set_aer_mmd(params, ¶ms->phy[phy_idx]); 13631 if (bnx2x_check_half_open_conn(params, vars, 1) != 13632 0) 13633 DP(NETIF_MSG_LINK, "Fault detection failed\n"); 13634 break; 13635 } 13636 } 13637 13638 if (CHIP_IS_E3(bp)) { 13639 struct bnx2x_phy *phy = ¶ms->phy[INT_PHY]; 13640 bnx2x_set_aer_mmd(params, phy); 13641 if ((phy->supported & SUPPORTED_20000baseKR2_Full) && 13642 (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_20G)) 13643 bnx2x_check_kr2_wa(params, vars, phy); 13644 bnx2x_check_over_curr(params, vars); 13645 if (vars->rx_tx_asic_rst) 13646 bnx2x_warpcore_config_runtime(phy, params, vars); 13647 13648 if ((REG_RD(bp, params->shmem_base + 13649 offsetof(struct shmem_region, dev_info. 13650 port_hw_config[params->port].default_cfg)) 13651 & PORT_HW_CFG_NET_SERDES_IF_MASK) == 13652 PORT_HW_CFG_NET_SERDES_IF_SFI) { 13653 if (bnx2x_is_sfp_module_plugged(phy, params)) { 13654 bnx2x_sfp_tx_fault_detection(phy, params, vars); 13655 } else if (vars->link_status & 13656 LINK_STATUS_SFP_TX_FAULT) { 13657 /* Clean trail, interrupt corrects the leds */ 13658 vars->link_status &= ~LINK_STATUS_SFP_TX_FAULT; 13659 vars->phy_flags &= ~PHY_SFP_TX_FAULT_FLAG; 13660 /* Update link status in the shared memory */ 13661 bnx2x_update_mng(params, vars->link_status); 13662 } 13663 } 13664 } 13665} 13666 13667u8 bnx2x_fan_failure_det_req(struct bnx2x *bp, 13668 u32 shmem_base, 13669 u32 shmem2_base, 13670 u8 port) 13671{ 13672 u8 phy_index, fan_failure_det_req = 0; 13673 struct bnx2x_phy phy; 13674 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS; 13675 phy_index++) { 13676 if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base, 13677 port, &phy) 13678 != 0) { 13679 DP(NETIF_MSG_LINK, "populate phy failed\n"); 13680 return 0; 13681 } 13682 fan_failure_det_req |= (phy.flags & 13683 FLAGS_FAN_FAILURE_DET_REQ); 13684 } 13685 return fan_failure_det_req; 13686} 13687 13688void bnx2x_hw_reset_phy(struct link_params *params) 13689{ 13690 u8 phy_index; 13691 struct bnx2x *bp = params->bp; 13692 bnx2x_update_mng(params, 0); 13693 bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, 13694 (NIG_MASK_XGXS0_LINK_STATUS | 13695 NIG_MASK_XGXS0_LINK10G | 13696 NIG_MASK_SERDES0_LINK_STATUS | 13697 NIG_MASK_MI_INT)); 13698 13699 for (phy_index = INT_PHY; phy_index < MAX_PHYS; 13700 phy_index++) { 13701 if (params->phy[phy_index].hw_reset) { 13702 params->phy[phy_index].hw_reset( 13703 ¶ms->phy[phy_index], 13704 params); 13705 params->phy[phy_index] = phy_null; 13706 } 13707 } 13708} 13709 13710void bnx2x_init_mod_abs_int(struct bnx2x *bp, struct link_vars *vars, 13711 u32 chip_id, u32 shmem_base, u32 shmem2_base, 13712 u8 port) 13713{ 13714 u8 gpio_num = 0xff, gpio_port = 0xff, phy_index; 13715 u32 val; 13716 u32 offset, aeu_mask, swap_val, swap_override, sync_offset; 13717 if (CHIP_IS_E3(bp)) { 13718 if (bnx2x_get_mod_abs_int_cfg(bp, chip_id, 13719 shmem_base, 13720 port, 13721 &gpio_num, 13722 &gpio_port) != 0) 13723 return; 13724 } else { 13725 struct bnx2x_phy phy; 13726 for (phy_index = EXT_PHY1; phy_index < MAX_PHYS; 13727 phy_index++) { 13728 if (bnx2x_populate_phy(bp, phy_index, shmem_base, 13729 shmem2_base, port, &phy) 13730 != 0) { 13731 DP(NETIF_MSG_LINK, "populate phy failed\n"); 13732 return; 13733 } 13734 if (phy.type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) { 13735 gpio_num = MISC_REGISTERS_GPIO_3; 13736 gpio_port = port; 13737 break; 13738 } 13739 } 13740 } 13741 13742 if (gpio_num == 0xff) 13743 return; 13744 13745 /* Set GPIO3 to trigger SFP+ module insertion/removal */ 13746 bnx2x_set_gpio(bp, gpio_num, MISC_REGISTERS_GPIO_INPUT_HI_Z, gpio_port); 13747 13748 swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); 13749 swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); 13750 gpio_port ^= (swap_val && swap_override); 13751 13752 vars->aeu_int_mask = AEU_INPUTS_ATTN_BITS_GPIO0_FUNCTION_0 << 13753 (gpio_num + (gpio_port << 2)); 13754 13755 sync_offset = shmem_base + 13756 offsetof(struct shmem_region, 13757 dev_info.port_hw_config[port].aeu_int_mask); 13758 REG_WR(bp, sync_offset, vars->aeu_int_mask); 13759 13760 DP(NETIF_MSG_LINK, "Setting MOD_ABS (GPIO%d_P%d) AEU to 0x%x\n", 13761 gpio_num, gpio_port, vars->aeu_int_mask); 13762 13763 if (port == 0) 13764 offset = MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0; 13765 else 13766 offset = MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0; 13767 13768 /* Open appropriate AEU for interrupts */ 13769 aeu_mask = REG_RD(bp, offset); 13770 aeu_mask |= vars->aeu_int_mask; 13771 REG_WR(bp, offset, aeu_mask); 13772 13773 /* Enable the GPIO to trigger interrupt */ 13774 val = REG_RD(bp, MISC_REG_GPIO_EVENT_EN); 13775 val |= 1 << (gpio_num + (gpio_port << 2)); 13776 REG_WR(bp, MISC_REG_GPIO_EVENT_EN, val); 13777} 13778