1/*
2 * Renesas RIIC driver
3 *
4 * Copyright (C) 2013 Wolfram Sang <wsa@sang-engineering.com>
5 * Copyright (C) 2013 Renesas Solutions Corp.
6 *
7 * This program is free software; you can redistribute it and/or modify it
8 * under the terms of the GNU General Public License version 2 as published by
9 * the Free Software Foundation.
10 */
11
12/*
13 * This i2c core has a lot of interrupts, namely 8. We use their chaining as
14 * some kind of state machine.
15 *
16 * 1) The main xfer routine kicks off a transmission by putting the start bit
17 * (or repeated start) on the bus and enabling the transmit interrupt (TIE)
18 * since we need to send the slave address + RW bit in every case.
19 *
20 * 2) TIE sends slave address + RW bit and selects how to continue.
21 *
22 * 3a) Write case: We keep utilizing TIE as long as we have data to send. If we
23 * are done, we switch over to the transmission done interrupt (TEIE) and mark
24 * the message as completed (includes sending STOP) there.
25 *
26 * 3b) Read case: We switch over to receive interrupt (RIE). One dummy read is
27 * needed to start clocking, then we keep receiving until we are done. Note
28 * that we use the RDRFS mode all the time, i.e. we ACK/NACK every byte by
29 * writing to the ACKBT bit. I tried using the RDRFS mode only at the end of a
30 * message to create the final NACK as sketched in the datasheet. This caused
31 * some subtle races (when byte n was processed and byte n+1 was already
32 * waiting), though, and I started with the safe approach.
33 *
34 * 4) If we got a NACK somewhere, we flag the error and stop the transmission
35 * via NAKIE.
36 *
37 * Also check the comments in the interrupt routines for some gory details.
38 */
39
40#include <linux/clk.h>
41#include <linux/completion.h>
42#include <linux/err.h>
43#include <linux/i2c.h>
44#include <linux/interrupt.h>
45#include <linux/io.h>
46#include <linux/module.h>
47#include <linux/of.h>
48#include <linux/platform_device.h>
49
50#define RIIC_ICCR1	0x00
51#define RIIC_ICCR2	0x04
52#define RIIC_ICMR1	0x08
53#define RIIC_ICMR3	0x10
54#define RIIC_ICSER	0x18
55#define RIIC_ICIER	0x1c
56#define RIIC_ICSR2	0x24
57#define RIIC_ICBRL	0x34
58#define RIIC_ICBRH	0x38
59#define RIIC_ICDRT	0x3c
60#define RIIC_ICDRR	0x40
61
62#define ICCR1_ICE	0x80
63#define ICCR1_IICRST	0x40
64#define ICCR1_SOWP	0x10
65
66#define ICCR2_BBSY	0x80
67#define ICCR2_SP	0x08
68#define ICCR2_RS	0x04
69#define ICCR2_ST	0x02
70
71#define ICMR1_CKS_MASK	0x70
72#define ICMR1_BCWP	0x08
73#define ICMR1_CKS(_x)	((((_x) << 4) & ICMR1_CKS_MASK) | ICMR1_BCWP)
74
75#define ICMR3_RDRFS	0x20
76#define ICMR3_ACKWP	0x10
77#define ICMR3_ACKBT	0x08
78
79#define ICIER_TIE	0x80
80#define ICIER_TEIE	0x40
81#define ICIER_RIE	0x20
82#define ICIER_NAKIE	0x10
83
84#define ICSR2_NACKF	0x10
85
86/* ICBRx (@ PCLK 33MHz) */
87#define ICBR_RESERVED	0xe0 /* Should be 1 on writes */
88#define ICBRL_SP100K	(19 | ICBR_RESERVED)
89#define ICBRH_SP100K	(16 | ICBR_RESERVED)
90#define ICBRL_SP400K	(21 | ICBR_RESERVED)
91#define ICBRH_SP400K	(9 | ICBR_RESERVED)
92
93#define RIIC_INIT_MSG	-1
94
95struct riic_dev {
96	void __iomem *base;
97	u8 *buf;
98	struct i2c_msg *msg;
99	int bytes_left;
100	int err;
101	int is_last;
102	struct completion msg_done;
103	struct i2c_adapter adapter;
104	struct clk *clk;
105};
106
107struct riic_irq_desc {
108	int res_num;
109	irq_handler_t isr;
110	char *name;
111};
112
113static inline void riic_clear_set_bit(struct riic_dev *riic, u8 clear, u8 set, u8 reg)
114{
115	writeb((readb(riic->base + reg) & ~clear) | set, riic->base + reg);
116}
117
118static int riic_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
119{
120	struct riic_dev *riic = i2c_get_adapdata(adap);
121	unsigned long time_left;
122	int i, ret;
123	u8 start_bit;
124
125	ret = clk_prepare_enable(riic->clk);
126	if (ret)
127		return ret;
128
129	if (readb(riic->base + RIIC_ICCR2) & ICCR2_BBSY) {
130		riic->err = -EBUSY;
131		goto out;
132	}
133
134	reinit_completion(&riic->msg_done);
135	riic->err = 0;
136
137	writeb(0, riic->base + RIIC_ICSR2);
138
139	for (i = 0, start_bit = ICCR2_ST; i < num; i++) {
140		riic->bytes_left = RIIC_INIT_MSG;
141		riic->buf = msgs[i].buf;
142		riic->msg = &msgs[i];
143		riic->is_last = (i == num - 1);
144
145		writeb(ICIER_NAKIE | ICIER_TIE, riic->base + RIIC_ICIER);
146
147		writeb(start_bit, riic->base + RIIC_ICCR2);
148
149		time_left = wait_for_completion_timeout(&riic->msg_done, riic->adapter.timeout);
150		if (time_left == 0)
151			riic->err = -ETIMEDOUT;
152
153		if (riic->err)
154			break;
155
156		start_bit = ICCR2_RS;
157	}
158
159 out:
160	clk_disable_unprepare(riic->clk);
161
162	return riic->err ?: num;
163}
164
165static irqreturn_t riic_tdre_isr(int irq, void *data)
166{
167	struct riic_dev *riic = data;
168	u8 val;
169
170	if (!riic->bytes_left)
171		return IRQ_NONE;
172
173	if (riic->bytes_left == RIIC_INIT_MSG) {
174		val = !!(riic->msg->flags & I2C_M_RD);
175		if (val)
176			/* On read, switch over to receive interrupt */
177			riic_clear_set_bit(riic, ICIER_TIE, ICIER_RIE, RIIC_ICIER);
178		else
179			/* On write, initialize length */
180			riic->bytes_left = riic->msg->len;
181
182		val |= (riic->msg->addr << 1);
183	} else {
184		val = *riic->buf;
185		riic->buf++;
186		riic->bytes_left--;
187	}
188
189	/*
190	 * Switch to transmission ended interrupt when done. Do check here
191	 * after bytes_left was initialized to support SMBUS_QUICK (new msg has
192	 * 0 length then)
193	 */
194	if (riic->bytes_left == 0)
195		riic_clear_set_bit(riic, ICIER_TIE, ICIER_TEIE, RIIC_ICIER);
196
197	/*
198	 * This acks the TIE interrupt. We get another TIE immediately if our
199	 * value could be moved to the shadow shift register right away. So
200	 * this must be after updates to ICIER (where we want to disable TIE)!
201	 */
202	writeb(val, riic->base + RIIC_ICDRT);
203
204	return IRQ_HANDLED;
205}
206
207static irqreturn_t riic_tend_isr(int irq, void *data)
208{
209	struct riic_dev *riic = data;
210
211	if (readb(riic->base + RIIC_ICSR2) & ICSR2_NACKF) {
212		/* We got a NACKIE */
213		readb(riic->base + RIIC_ICDRR);	/* dummy read */
214		riic->err = -ENXIO;
215	} else if (riic->bytes_left) {
216		return IRQ_NONE;
217	}
218
219	if (riic->is_last || riic->err)
220		writeb(ICCR2_SP, riic->base + RIIC_ICCR2);
221
222	writeb(0, riic->base + RIIC_ICIER);
223	complete(&riic->msg_done);
224
225	return IRQ_HANDLED;
226}
227
228static irqreturn_t riic_rdrf_isr(int irq, void *data)
229{
230	struct riic_dev *riic = data;
231
232	if (!riic->bytes_left)
233		return IRQ_NONE;
234
235	if (riic->bytes_left == RIIC_INIT_MSG) {
236		riic->bytes_left = riic->msg->len;
237		readb(riic->base + RIIC_ICDRR);	/* dummy read */
238		return IRQ_HANDLED;
239	}
240
241	if (riic->bytes_left == 1) {
242		/* STOP must come before we set ACKBT! */
243		if (riic->is_last)
244			writeb(ICCR2_SP, riic->base + RIIC_ICCR2);
245
246		riic_clear_set_bit(riic, 0, ICMR3_ACKBT, RIIC_ICMR3);
247
248		writeb(0, riic->base + RIIC_ICIER);
249		complete(&riic->msg_done);
250	} else {
251		riic_clear_set_bit(riic, ICMR3_ACKBT, 0, RIIC_ICMR3);
252	}
253
254	/* Reading acks the RIE interrupt */
255	*riic->buf = readb(riic->base + RIIC_ICDRR);
256	riic->buf++;
257	riic->bytes_left--;
258
259	return IRQ_HANDLED;
260}
261
262static u32 riic_func(struct i2c_adapter *adap)
263{
264	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
265}
266
267static const struct i2c_algorithm riic_algo = {
268	.master_xfer	= riic_xfer,
269	.functionality	= riic_func,
270};
271
272static int riic_init_hw(struct riic_dev *riic, u32 spd)
273{
274	int ret;
275	unsigned long rate;
276
277	ret = clk_prepare_enable(riic->clk);
278	if (ret)
279		return ret;
280
281	/*
282	 * TODO: Implement formula to calculate the timing values depending on
283	 * variable parent clock rate and arbitrary bus speed
284	 */
285	rate = clk_get_rate(riic->clk);
286	if (rate != 33325000) {
287		dev_err(&riic->adapter.dev,
288			"invalid parent clk (%lu). Must be 33325000Hz\n", rate);
289		clk_disable_unprepare(riic->clk);
290		return -EINVAL;
291	}
292
293	/* Changing the order of accessing IICRST and ICE may break things! */
294	writeb(ICCR1_IICRST | ICCR1_SOWP, riic->base + RIIC_ICCR1);
295	riic_clear_set_bit(riic, 0, ICCR1_ICE, RIIC_ICCR1);
296
297	switch (spd) {
298	case 100000:
299		writeb(ICMR1_CKS(3), riic->base + RIIC_ICMR1);
300		writeb(ICBRH_SP100K, riic->base + RIIC_ICBRH);
301		writeb(ICBRL_SP100K, riic->base + RIIC_ICBRL);
302		break;
303	case 400000:
304		writeb(ICMR1_CKS(1), riic->base + RIIC_ICMR1);
305		writeb(ICBRH_SP400K, riic->base + RIIC_ICBRH);
306		writeb(ICBRL_SP400K, riic->base + RIIC_ICBRL);
307		break;
308	default:
309		dev_err(&riic->adapter.dev,
310			"unsupported bus speed (%dHz). Use 100000 or 400000\n", spd);
311		clk_disable_unprepare(riic->clk);
312		return -EINVAL;
313	}
314
315	writeb(0, riic->base + RIIC_ICSER);
316	writeb(ICMR3_ACKWP | ICMR3_RDRFS, riic->base + RIIC_ICMR3);
317
318	riic_clear_set_bit(riic, ICCR1_IICRST, 0, RIIC_ICCR1);
319
320	clk_disable_unprepare(riic->clk);
321
322	return 0;
323}
324
325static struct riic_irq_desc riic_irqs[] = {
326	{ .res_num = 0, .isr = riic_tend_isr, .name = "riic-tend" },
327	{ .res_num = 1, .isr = riic_rdrf_isr, .name = "riic-rdrf" },
328	{ .res_num = 2, .isr = riic_tdre_isr, .name = "riic-tdre" },
329	{ .res_num = 5, .isr = riic_tend_isr, .name = "riic-nack" },
330};
331
332static int riic_i2c_probe(struct platform_device *pdev)
333{
334	struct device_node *np = pdev->dev.of_node;
335	struct riic_dev *riic;
336	struct i2c_adapter *adap;
337	struct resource *res;
338	u32 bus_rate = 0;
339	int i, ret;
340
341	riic = devm_kzalloc(&pdev->dev, sizeof(*riic), GFP_KERNEL);
342	if (!riic)
343		return -ENOMEM;
344
345	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
346	riic->base = devm_ioremap_resource(&pdev->dev, res);
347	if (IS_ERR(riic->base))
348		return PTR_ERR(riic->base);
349
350	riic->clk = devm_clk_get(&pdev->dev, NULL);
351	if (IS_ERR(riic->clk)) {
352		dev_err(&pdev->dev, "missing controller clock");
353		return PTR_ERR(riic->clk);
354	}
355
356	for (i = 0; i < ARRAY_SIZE(riic_irqs); i++) {
357		res = platform_get_resource(pdev, IORESOURCE_IRQ, riic_irqs[i].res_num);
358		if (!res)
359			return -ENODEV;
360
361		ret = devm_request_irq(&pdev->dev, res->start, riic_irqs[i].isr,
362					0, riic_irqs[i].name, riic);
363		if (ret) {
364			dev_err(&pdev->dev, "failed to request irq %s\n", riic_irqs[i].name);
365			return ret;
366		}
367	}
368
369	adap = &riic->adapter;
370	i2c_set_adapdata(adap, riic);
371	strlcpy(adap->name, "Renesas RIIC adapter", sizeof(adap->name));
372	adap->owner = THIS_MODULE;
373	adap->algo = &riic_algo;
374	adap->dev.parent = &pdev->dev;
375	adap->dev.of_node = pdev->dev.of_node;
376
377	init_completion(&riic->msg_done);
378
379	of_property_read_u32(np, "clock-frequency", &bus_rate);
380	ret = riic_init_hw(riic, bus_rate);
381	if (ret)
382		return ret;
383
384
385	ret = i2c_add_adapter(adap);
386	if (ret) {
387		dev_err(&pdev->dev, "failed to add adapter\n");
388		return ret;
389	}
390
391	platform_set_drvdata(pdev, riic);
392
393	dev_info(&pdev->dev, "registered with %dHz bus speed\n", bus_rate);
394	return 0;
395}
396
397static int riic_i2c_remove(struct platform_device *pdev)
398{
399	struct riic_dev *riic = platform_get_drvdata(pdev);
400
401	writeb(0, riic->base + RIIC_ICIER);
402	i2c_del_adapter(&riic->adapter);
403
404	return 0;
405}
406
407static const struct of_device_id riic_i2c_dt_ids[] = {
408	{ .compatible = "renesas,riic-rz" },
409	{ /* Sentinel */ },
410};
411
412static struct platform_driver riic_i2c_driver = {
413	.probe		= riic_i2c_probe,
414	.remove		= riic_i2c_remove,
415	.driver		= {
416		.name	= "i2c-riic",
417		.of_match_table = riic_i2c_dt_ids,
418	},
419};
420
421module_platform_driver(riic_i2c_driver);
422
423MODULE_DESCRIPTION("Renesas RIIC adapter");
424MODULE_AUTHOR("Wolfram Sang <wsa@sang-engineering.com>");
425MODULE_LICENSE("GPL v2");
426MODULE_DEVICE_TABLE(of, riic_i2c_dt_ids);
427