1/* 2 * Freescale MXS I2C bus driver 3 * 4 * Copyright (C) 2012-2013 Marek Vasut <marex@denx.de> 5 * Copyright (C) 2011-2012 Wolfram Sang, Pengutronix e.K. 6 * 7 * based on a (non-working) driver which was: 8 * 9 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved. 10 * 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License as published by 13 * the Free Software Foundation; either version 2 of the License, or 14 * (at your option) any later version. 15 * 16 */ 17 18#include <linux/slab.h> 19#include <linux/device.h> 20#include <linux/module.h> 21#include <linux/i2c.h> 22#include <linux/err.h> 23#include <linux/interrupt.h> 24#include <linux/completion.h> 25#include <linux/platform_device.h> 26#include <linux/jiffies.h> 27#include <linux/io.h> 28#include <linux/stmp_device.h> 29#include <linux/of.h> 30#include <linux/of_device.h> 31#include <linux/dma-mapping.h> 32#include <linux/dmaengine.h> 33 34#define DRIVER_NAME "mxs-i2c" 35 36#define MXS_I2C_CTRL0 (0x00) 37#define MXS_I2C_CTRL0_SET (0x04) 38#define MXS_I2C_CTRL0_CLR (0x08) 39 40#define MXS_I2C_CTRL0_SFTRST 0x80000000 41#define MXS_I2C_CTRL0_RUN 0x20000000 42#define MXS_I2C_CTRL0_SEND_NAK_ON_LAST 0x02000000 43#define MXS_I2C_CTRL0_PIO_MODE 0x01000000 44#define MXS_I2C_CTRL0_RETAIN_CLOCK 0x00200000 45#define MXS_I2C_CTRL0_POST_SEND_STOP 0x00100000 46#define MXS_I2C_CTRL0_PRE_SEND_START 0x00080000 47#define MXS_I2C_CTRL0_MASTER_MODE 0x00020000 48#define MXS_I2C_CTRL0_DIRECTION 0x00010000 49#define MXS_I2C_CTRL0_XFER_COUNT(v) ((v) & 0x0000FFFF) 50 51#define MXS_I2C_TIMING0 (0x10) 52#define MXS_I2C_TIMING1 (0x20) 53#define MXS_I2C_TIMING2 (0x30) 54 55#define MXS_I2C_CTRL1 (0x40) 56#define MXS_I2C_CTRL1_SET (0x44) 57#define MXS_I2C_CTRL1_CLR (0x48) 58 59#define MXS_I2C_CTRL1_CLR_GOT_A_NAK 0x10000000 60#define MXS_I2C_CTRL1_BUS_FREE_IRQ 0x80 61#define MXS_I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ 0x40 62#define MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ 0x20 63#define MXS_I2C_CTRL1_OVERSIZE_XFER_TERM_IRQ 0x10 64#define MXS_I2C_CTRL1_EARLY_TERM_IRQ 0x08 65#define MXS_I2C_CTRL1_MASTER_LOSS_IRQ 0x04 66#define MXS_I2C_CTRL1_SLAVE_STOP_IRQ 0x02 67#define MXS_I2C_CTRL1_SLAVE_IRQ 0x01 68 69#define MXS_I2C_STAT (0x50) 70#define MXS_I2C_STAT_GOT_A_NAK 0x10000000 71#define MXS_I2C_STAT_BUS_BUSY 0x00000800 72#define MXS_I2C_STAT_CLK_GEN_BUSY 0x00000400 73 74#define MXS_I2C_DATA(i2c) ((i2c->dev_type == MXS_I2C_V1) ? 0x60 : 0xa0) 75 76#define MXS_I2C_DEBUG0_CLR(i2c) ((i2c->dev_type == MXS_I2C_V1) ? 0x78 : 0xb8) 77 78#define MXS_I2C_DEBUG0_DMAREQ 0x80000000 79 80#define MXS_I2C_IRQ_MASK (MXS_I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ | \ 81 MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ | \ 82 MXS_I2C_CTRL1_EARLY_TERM_IRQ | \ 83 MXS_I2C_CTRL1_MASTER_LOSS_IRQ | \ 84 MXS_I2C_CTRL1_SLAVE_STOP_IRQ | \ 85 MXS_I2C_CTRL1_SLAVE_IRQ) 86 87 88#define MXS_CMD_I2C_SELECT (MXS_I2C_CTRL0_RETAIN_CLOCK | \ 89 MXS_I2C_CTRL0_PRE_SEND_START | \ 90 MXS_I2C_CTRL0_MASTER_MODE | \ 91 MXS_I2C_CTRL0_DIRECTION | \ 92 MXS_I2C_CTRL0_XFER_COUNT(1)) 93 94#define MXS_CMD_I2C_WRITE (MXS_I2C_CTRL0_PRE_SEND_START | \ 95 MXS_I2C_CTRL0_MASTER_MODE | \ 96 MXS_I2C_CTRL0_DIRECTION) 97 98#define MXS_CMD_I2C_READ (MXS_I2C_CTRL0_SEND_NAK_ON_LAST | \ 99 MXS_I2C_CTRL0_MASTER_MODE) 100 101enum mxs_i2c_devtype { 102 MXS_I2C_UNKNOWN = 0, 103 MXS_I2C_V1, 104 MXS_I2C_V2, 105}; 106 107/** 108 * struct mxs_i2c_dev - per device, private MXS-I2C data 109 * 110 * @dev: driver model device node 111 * @dev_type: distinguish i.MX23/i.MX28 features 112 * @regs: IO registers pointer 113 * @cmd_complete: completion object for transaction wait 114 * @cmd_err: error code for last transaction 115 * @adapter: i2c subsystem adapter node 116 */ 117struct mxs_i2c_dev { 118 struct device *dev; 119 enum mxs_i2c_devtype dev_type; 120 void __iomem *regs; 121 struct completion cmd_complete; 122 int cmd_err; 123 struct i2c_adapter adapter; 124 125 uint32_t timing0; 126 uint32_t timing1; 127 uint32_t timing2; 128 129 /* DMA support components */ 130 struct dma_chan *dmach; 131 uint32_t pio_data[2]; 132 uint32_t addr_data; 133 struct scatterlist sg_io[2]; 134 bool dma_read; 135}; 136 137static int mxs_i2c_reset(struct mxs_i2c_dev *i2c) 138{ 139 int ret = stmp_reset_block(i2c->regs); 140 if (ret) 141 return ret; 142 143 /* 144 * Configure timing for the I2C block. The I2C TIMING2 register has to 145 * be programmed with this particular magic number. The rest is derived 146 * from the XTAL speed and requested I2C speed. 147 * 148 * For details, see i.MX233 [25.4.2 - 25.4.4] and i.MX28 [27.5.2 - 27.5.4]. 149 */ 150 writel(i2c->timing0, i2c->regs + MXS_I2C_TIMING0); 151 writel(i2c->timing1, i2c->regs + MXS_I2C_TIMING1); 152 writel(i2c->timing2, i2c->regs + MXS_I2C_TIMING2); 153 154 writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET); 155 156 return 0; 157} 158 159static void mxs_i2c_dma_finish(struct mxs_i2c_dev *i2c) 160{ 161 if (i2c->dma_read) { 162 dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); 163 dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); 164 } else { 165 dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); 166 } 167} 168 169static void mxs_i2c_dma_irq_callback(void *param) 170{ 171 struct mxs_i2c_dev *i2c = param; 172 173 complete(&i2c->cmd_complete); 174 mxs_i2c_dma_finish(i2c); 175} 176 177static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap, 178 struct i2c_msg *msg, uint32_t flags) 179{ 180 struct dma_async_tx_descriptor *desc; 181 struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); 182 183 if (msg->flags & I2C_M_RD) { 184 i2c->dma_read = 1; 185 i2c->addr_data = (msg->addr << 1) | I2C_SMBUS_READ; 186 187 /* 188 * SELECT command. 189 */ 190 191 /* Queue the PIO register write transfer. */ 192 i2c->pio_data[0] = MXS_CMD_I2C_SELECT; 193 desc = dmaengine_prep_slave_sg(i2c->dmach, 194 (struct scatterlist *)&i2c->pio_data[0], 195 1, DMA_TRANS_NONE, 0); 196 if (!desc) { 197 dev_err(i2c->dev, 198 "Failed to get PIO reg. write descriptor.\n"); 199 goto select_init_pio_fail; 200 } 201 202 /* Queue the DMA data transfer. */ 203 sg_init_one(&i2c->sg_io[0], &i2c->addr_data, 1); 204 dma_map_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); 205 desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[0], 1, 206 DMA_MEM_TO_DEV, 207 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 208 if (!desc) { 209 dev_err(i2c->dev, 210 "Failed to get DMA data write descriptor.\n"); 211 goto select_init_dma_fail; 212 } 213 214 /* 215 * READ command. 216 */ 217 218 /* Queue the PIO register write transfer. */ 219 i2c->pio_data[1] = flags | MXS_CMD_I2C_READ | 220 MXS_I2C_CTRL0_XFER_COUNT(msg->len); 221 desc = dmaengine_prep_slave_sg(i2c->dmach, 222 (struct scatterlist *)&i2c->pio_data[1], 223 1, DMA_TRANS_NONE, DMA_PREP_INTERRUPT); 224 if (!desc) { 225 dev_err(i2c->dev, 226 "Failed to get PIO reg. write descriptor.\n"); 227 goto select_init_dma_fail; 228 } 229 230 /* Queue the DMA data transfer. */ 231 sg_init_one(&i2c->sg_io[1], msg->buf, msg->len); 232 dma_map_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); 233 desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[1], 1, 234 DMA_DEV_TO_MEM, 235 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 236 if (!desc) { 237 dev_err(i2c->dev, 238 "Failed to get DMA data write descriptor.\n"); 239 goto read_init_dma_fail; 240 } 241 } else { 242 i2c->dma_read = 0; 243 i2c->addr_data = (msg->addr << 1) | I2C_SMBUS_WRITE; 244 245 /* 246 * WRITE command. 247 */ 248 249 /* Queue the PIO register write transfer. */ 250 i2c->pio_data[0] = flags | MXS_CMD_I2C_WRITE | 251 MXS_I2C_CTRL0_XFER_COUNT(msg->len + 1); 252 desc = dmaengine_prep_slave_sg(i2c->dmach, 253 (struct scatterlist *)&i2c->pio_data[0], 254 1, DMA_TRANS_NONE, 0); 255 if (!desc) { 256 dev_err(i2c->dev, 257 "Failed to get PIO reg. write descriptor.\n"); 258 goto write_init_pio_fail; 259 } 260 261 /* Queue the DMA data transfer. */ 262 sg_init_table(i2c->sg_io, 2); 263 sg_set_buf(&i2c->sg_io[0], &i2c->addr_data, 1); 264 sg_set_buf(&i2c->sg_io[1], msg->buf, msg->len); 265 dma_map_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); 266 desc = dmaengine_prep_slave_sg(i2c->dmach, i2c->sg_io, 2, 267 DMA_MEM_TO_DEV, 268 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 269 if (!desc) { 270 dev_err(i2c->dev, 271 "Failed to get DMA data write descriptor.\n"); 272 goto write_init_dma_fail; 273 } 274 } 275 276 /* 277 * The last descriptor must have this callback, 278 * to finish the DMA transaction. 279 */ 280 desc->callback = mxs_i2c_dma_irq_callback; 281 desc->callback_param = i2c; 282 283 /* Start the transfer. */ 284 dmaengine_submit(desc); 285 dma_async_issue_pending(i2c->dmach); 286 return 0; 287 288/* Read failpath. */ 289read_init_dma_fail: 290 dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); 291select_init_dma_fail: 292 dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); 293select_init_pio_fail: 294 dmaengine_terminate_all(i2c->dmach); 295 return -EINVAL; 296 297/* Write failpath. */ 298write_init_dma_fail: 299 dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); 300write_init_pio_fail: 301 dmaengine_terminate_all(i2c->dmach); 302 return -EINVAL; 303} 304 305static int mxs_i2c_pio_wait_xfer_end(struct mxs_i2c_dev *i2c) 306{ 307 unsigned long timeout = jiffies + msecs_to_jiffies(1000); 308 309 while (readl(i2c->regs + MXS_I2C_CTRL0) & MXS_I2C_CTRL0_RUN) { 310 if (readl(i2c->regs + MXS_I2C_CTRL1) & 311 MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) 312 return -ENXIO; 313 if (time_after(jiffies, timeout)) 314 return -ETIMEDOUT; 315 cond_resched(); 316 } 317 318 return 0; 319} 320 321static int mxs_i2c_pio_check_error_state(struct mxs_i2c_dev *i2c) 322{ 323 u32 state; 324 325 state = readl(i2c->regs + MXS_I2C_CTRL1_CLR) & MXS_I2C_IRQ_MASK; 326 327 if (state & MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) 328 i2c->cmd_err = -ENXIO; 329 else if (state & (MXS_I2C_CTRL1_EARLY_TERM_IRQ | 330 MXS_I2C_CTRL1_MASTER_LOSS_IRQ | 331 MXS_I2C_CTRL1_SLAVE_STOP_IRQ | 332 MXS_I2C_CTRL1_SLAVE_IRQ)) 333 i2c->cmd_err = -EIO; 334 335 return i2c->cmd_err; 336} 337 338static void mxs_i2c_pio_trigger_cmd(struct mxs_i2c_dev *i2c, u32 cmd) 339{ 340 u32 reg; 341 342 writel(cmd, i2c->regs + MXS_I2C_CTRL0); 343 344 /* readback makes sure the write is latched into hardware */ 345 reg = readl(i2c->regs + MXS_I2C_CTRL0); 346 reg |= MXS_I2C_CTRL0_RUN; 347 writel(reg, i2c->regs + MXS_I2C_CTRL0); 348} 349 350/* 351 * Start WRITE transaction on the I2C bus. By studying i.MX23 datasheet, 352 * CTRL0::PIO_MODE bit description clarifies the order in which the registers 353 * must be written during PIO mode operation. First, the CTRL0 register has 354 * to be programmed with all the necessary bits but the RUN bit. Then the 355 * payload has to be written into the DATA register. Finally, the transmission 356 * is executed by setting the RUN bit in CTRL0. 357 */ 358static void mxs_i2c_pio_trigger_write_cmd(struct mxs_i2c_dev *i2c, u32 cmd, 359 u32 data) 360{ 361 writel(cmd, i2c->regs + MXS_I2C_CTRL0); 362 363 if (i2c->dev_type == MXS_I2C_V1) 364 writel(MXS_I2C_CTRL0_PIO_MODE, i2c->regs + MXS_I2C_CTRL0_SET); 365 366 writel(data, i2c->regs + MXS_I2C_DATA(i2c)); 367 writel(MXS_I2C_CTRL0_RUN, i2c->regs + MXS_I2C_CTRL0_SET); 368} 369 370static int mxs_i2c_pio_setup_xfer(struct i2c_adapter *adap, 371 struct i2c_msg *msg, uint32_t flags) 372{ 373 struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); 374 uint32_t addr_data = msg->addr << 1; 375 uint32_t data = 0; 376 int i, ret, xlen = 0, xmit = 0; 377 uint32_t start; 378 379 /* Mute IRQs coming from this block. */ 380 writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_CLR); 381 382 /* 383 * MX23 idea: 384 * - Enable CTRL0::PIO_MODE (1 << 24) 385 * - Enable CTRL1::ACK_MODE (1 << 27) 386 * 387 * WARNING! The MX23 is broken in some way, even if it claims 388 * to support PIO, when we try to transfer any amount of data 389 * that is not aligned to 4 bytes, the DMA engine will have 390 * bits in DEBUG1::DMA_BYTES_ENABLES still set even after the 391 * transfer. This in turn will mess up the next transfer as 392 * the block it emit one byte write onto the bus terminated 393 * with a NAK+STOP. A possible workaround is to reset the IP 394 * block after every PIO transmission, which might just work. 395 * 396 * NOTE: The CTRL0::PIO_MODE description is important, since 397 * it outlines how the PIO mode is really supposed to work. 398 */ 399 if (msg->flags & I2C_M_RD) { 400 /* 401 * PIO READ transfer: 402 * 403 * This transfer MUST be limited to 4 bytes maximum. It is not 404 * possible to transfer more than four bytes via PIO, since we 405 * can not in any way make sure we can read the data from the 406 * DATA register fast enough. Besides, the RX FIFO is only four 407 * bytes deep, thus we can only really read up to four bytes at 408 * time. Finally, there is no bit indicating us that new data 409 * arrived at the FIFO and can thus be fetched from the DATA 410 * register. 411 */ 412 BUG_ON(msg->len > 4); 413 414 addr_data |= I2C_SMBUS_READ; 415 416 /* SELECT command. */ 417 mxs_i2c_pio_trigger_write_cmd(i2c, MXS_CMD_I2C_SELECT, 418 addr_data); 419 420 ret = mxs_i2c_pio_wait_xfer_end(i2c); 421 if (ret) { 422 dev_err(i2c->dev, 423 "PIO: Failed to send SELECT command!\n"); 424 goto cleanup; 425 } 426 427 /* READ command. */ 428 mxs_i2c_pio_trigger_cmd(i2c, 429 MXS_CMD_I2C_READ | flags | 430 MXS_I2C_CTRL0_XFER_COUNT(msg->len)); 431 432 ret = mxs_i2c_pio_wait_xfer_end(i2c); 433 if (ret) { 434 dev_err(i2c->dev, 435 "PIO: Failed to send READ command!\n"); 436 goto cleanup; 437 } 438 439 data = readl(i2c->regs + MXS_I2C_DATA(i2c)); 440 for (i = 0; i < msg->len; i++) { 441 msg->buf[i] = data & 0xff; 442 data >>= 8; 443 } 444 } else { 445 /* 446 * PIO WRITE transfer: 447 * 448 * The code below implements clock stretching to circumvent 449 * the possibility of kernel not being able to supply data 450 * fast enough. It is possible to transfer arbitrary amount 451 * of data using PIO write. 452 */ 453 addr_data |= I2C_SMBUS_WRITE; 454 455 /* 456 * The LSB of data buffer is the first byte blasted across 457 * the bus. Higher order bytes follow. Thus the following 458 * filling schematic. 459 */ 460 461 data = addr_data << 24; 462 463 /* Start the transfer with START condition. */ 464 start = MXS_I2C_CTRL0_PRE_SEND_START; 465 466 /* If the transfer is long, use clock stretching. */ 467 if (msg->len > 3) 468 start |= MXS_I2C_CTRL0_RETAIN_CLOCK; 469 470 for (i = 0; i < msg->len; i++) { 471 data >>= 8; 472 data |= (msg->buf[i] << 24); 473 474 xmit = 0; 475 476 /* This is the last transfer of the message. */ 477 if (i + 1 == msg->len) { 478 /* Add optional STOP flag. */ 479 start |= flags; 480 /* Remove RETAIN_CLOCK bit. */ 481 start &= ~MXS_I2C_CTRL0_RETAIN_CLOCK; 482 xmit = 1; 483 } 484 485 /* Four bytes are ready in the "data" variable. */ 486 if ((i & 3) == 2) 487 xmit = 1; 488 489 /* Nothing interesting happened, continue stuffing. */ 490 if (!xmit) 491 continue; 492 493 /* 494 * Compute the size of the transfer and shift the 495 * data accordingly. 496 * 497 * i = (4k + 0) .... xlen = 2 498 * i = (4k + 1) .... xlen = 3 499 * i = (4k + 2) .... xlen = 4 500 * i = (4k + 3) .... xlen = 1 501 */ 502 503 if ((i % 4) == 3) 504 xlen = 1; 505 else 506 xlen = (i % 4) + 2; 507 508 data >>= (4 - xlen) * 8; 509 510 dev_dbg(i2c->dev, 511 "PIO: len=%i pos=%i total=%i [W%s%s%s]\n", 512 xlen, i, msg->len, 513 start & MXS_I2C_CTRL0_PRE_SEND_START ? "S" : "", 514 start & MXS_I2C_CTRL0_POST_SEND_STOP ? "E" : "", 515 start & MXS_I2C_CTRL0_RETAIN_CLOCK ? "C" : ""); 516 517 writel(MXS_I2C_DEBUG0_DMAREQ, 518 i2c->regs + MXS_I2C_DEBUG0_CLR(i2c)); 519 520 mxs_i2c_pio_trigger_write_cmd(i2c, 521 start | MXS_I2C_CTRL0_MASTER_MODE | 522 MXS_I2C_CTRL0_DIRECTION | 523 MXS_I2C_CTRL0_XFER_COUNT(xlen), data); 524 525 /* The START condition is sent only once. */ 526 start &= ~MXS_I2C_CTRL0_PRE_SEND_START; 527 528 /* Wait for the end of the transfer. */ 529 ret = mxs_i2c_pio_wait_xfer_end(i2c); 530 if (ret) { 531 dev_err(i2c->dev, 532 "PIO: Failed to finish WRITE cmd!\n"); 533 break; 534 } 535 536 /* Check NAK here. */ 537 ret = readl(i2c->regs + MXS_I2C_STAT) & 538 MXS_I2C_STAT_GOT_A_NAK; 539 if (ret) { 540 ret = -ENXIO; 541 goto cleanup; 542 } 543 } 544 } 545 546 /* make sure we capture any occurred error into cmd_err */ 547 ret = mxs_i2c_pio_check_error_state(i2c); 548 549cleanup: 550 /* Clear any dangling IRQs and re-enable interrupts. */ 551 writel(MXS_I2C_IRQ_MASK, i2c->regs + MXS_I2C_CTRL1_CLR); 552 writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET); 553 554 /* Clear the PIO_MODE on i.MX23 */ 555 if (i2c->dev_type == MXS_I2C_V1) 556 writel(MXS_I2C_CTRL0_PIO_MODE, i2c->regs + MXS_I2C_CTRL0_CLR); 557 558 return ret; 559} 560 561/* 562 * Low level master read/write transaction. 563 */ 564static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, 565 int stop) 566{ 567 struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); 568 int ret; 569 int flags; 570 int use_pio = 0; 571 unsigned long time_left; 572 573 flags = stop ? MXS_I2C_CTRL0_POST_SEND_STOP : 0; 574 575 dev_dbg(i2c->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n", 576 msg->addr, msg->len, msg->flags, stop); 577 578 if (msg->len == 0) 579 return -EINVAL; 580 581 /* 582 * The MX28 I2C IP block can only do PIO READ for transfer of to up 583 * 4 bytes of length. The write transfer is not limited as it can use 584 * clock stretching to avoid FIFO underruns. 585 */ 586 if ((msg->flags & I2C_M_RD) && (msg->len <= 4)) 587 use_pio = 1; 588 if (!(msg->flags & I2C_M_RD) && (msg->len < 7)) 589 use_pio = 1; 590 591 i2c->cmd_err = 0; 592 if (use_pio) { 593 ret = mxs_i2c_pio_setup_xfer(adap, msg, flags); 594 /* No need to reset the block if NAK was received. */ 595 if (ret && (ret != -ENXIO)) 596 mxs_i2c_reset(i2c); 597 } else { 598 reinit_completion(&i2c->cmd_complete); 599 ret = mxs_i2c_dma_setup_xfer(adap, msg, flags); 600 if (ret) 601 return ret; 602 603 time_left = wait_for_completion_timeout(&i2c->cmd_complete, 604 msecs_to_jiffies(1000)); 605 if (!time_left) 606 goto timeout; 607 608 ret = i2c->cmd_err; 609 } 610 611 if (ret == -ENXIO) { 612 /* 613 * If the transfer fails with a NAK from the slave the 614 * controller halts until it gets told to return to idle state. 615 */ 616 writel(MXS_I2C_CTRL1_CLR_GOT_A_NAK, 617 i2c->regs + MXS_I2C_CTRL1_SET); 618 } 619 620 /* 621 * WARNING! 622 * The i.MX23 is strange. After each and every operation, it's I2C IP 623 * block must be reset, otherwise the IP block will misbehave. This can 624 * be observed on the bus by the block sending out one single byte onto 625 * the bus. In case such an error happens, bit 27 will be set in the 626 * DEBUG0 register. This bit is not documented in the i.MX23 datasheet 627 * and is marked as "TBD" instead. To reset this bit to a correct state, 628 * reset the whole block. Since the block reset does not take long, do 629 * reset the block after every transfer to play safe. 630 */ 631 if (i2c->dev_type == MXS_I2C_V1) 632 mxs_i2c_reset(i2c); 633 634 dev_dbg(i2c->dev, "Done with err=%d\n", ret); 635 636 return ret; 637 638timeout: 639 dev_dbg(i2c->dev, "Timeout!\n"); 640 mxs_i2c_dma_finish(i2c); 641 ret = mxs_i2c_reset(i2c); 642 if (ret) 643 return ret; 644 645 return -ETIMEDOUT; 646} 647 648static int mxs_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], 649 int num) 650{ 651 int i; 652 int err; 653 654 for (i = 0; i < num; i++) { 655 err = mxs_i2c_xfer_msg(adap, &msgs[i], i == (num - 1)); 656 if (err) 657 return err; 658 } 659 660 return num; 661} 662 663static u32 mxs_i2c_func(struct i2c_adapter *adap) 664{ 665 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; 666} 667 668static irqreturn_t mxs_i2c_isr(int this_irq, void *dev_id) 669{ 670 struct mxs_i2c_dev *i2c = dev_id; 671 u32 stat = readl(i2c->regs + MXS_I2C_CTRL1) & MXS_I2C_IRQ_MASK; 672 673 if (!stat) 674 return IRQ_NONE; 675 676 if (stat & MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) 677 i2c->cmd_err = -ENXIO; 678 else if (stat & (MXS_I2C_CTRL1_EARLY_TERM_IRQ | 679 MXS_I2C_CTRL1_MASTER_LOSS_IRQ | 680 MXS_I2C_CTRL1_SLAVE_STOP_IRQ | MXS_I2C_CTRL1_SLAVE_IRQ)) 681 /* MXS_I2C_CTRL1_OVERSIZE_XFER_TERM_IRQ is only for slaves */ 682 i2c->cmd_err = -EIO; 683 684 writel(stat, i2c->regs + MXS_I2C_CTRL1_CLR); 685 686 return IRQ_HANDLED; 687} 688 689static const struct i2c_algorithm mxs_i2c_algo = { 690 .master_xfer = mxs_i2c_xfer, 691 .functionality = mxs_i2c_func, 692}; 693 694static void mxs_i2c_derive_timing(struct mxs_i2c_dev *i2c, uint32_t speed) 695{ 696 /* The I2C block clock runs at 24MHz */ 697 const uint32_t clk = 24000000; 698 uint32_t divider; 699 uint16_t high_count, low_count, rcv_count, xmit_count; 700 uint32_t bus_free, leadin; 701 struct device *dev = i2c->dev; 702 703 divider = DIV_ROUND_UP(clk, speed); 704 705 if (divider < 25) { 706 /* 707 * limit the divider, so that min(low_count, high_count) 708 * is >= 1 709 */ 710 divider = 25; 711 dev_warn(dev, 712 "Speed too high (%u.%03u kHz), using %u.%03u kHz\n", 713 speed / 1000, speed % 1000, 714 clk / divider / 1000, clk / divider % 1000); 715 } else if (divider > 1897) { 716 /* 717 * limit the divider, so that max(low_count, high_count) 718 * cannot exceed 1023 719 */ 720 divider = 1897; 721 dev_warn(dev, 722 "Speed too low (%u.%03u kHz), using %u.%03u kHz\n", 723 speed / 1000, speed % 1000, 724 clk / divider / 1000, clk / divider % 1000); 725 } 726 727 /* 728 * The I2C spec specifies the following timing data: 729 * standard mode fast mode Bitfield name 730 * tLOW (SCL LOW period) 4700 ns 1300 ns 731 * tHIGH (SCL HIGH period) 4000 ns 600 ns 732 * tSU;DAT (data setup time) 250 ns 100 ns 733 * tHD;STA (START hold time) 4000 ns 600 ns 734 * tBUF (bus free time) 4700 ns 1300 ns 735 * 736 * The hardware (of the i.MX28 at least) seems to add 2 additional 737 * clock cycles to the low_count and 7 cycles to the high_count. 738 * This is compensated for by subtracting the respective constants 739 * from the values written to the timing registers. 740 */ 741 if (speed > 100000) { 742 /* fast mode */ 743 low_count = DIV_ROUND_CLOSEST(divider * 13, (13 + 6)); 744 high_count = DIV_ROUND_CLOSEST(divider * 6, (13 + 6)); 745 leadin = DIV_ROUND_UP(600 * (clk / 1000000), 1000); 746 bus_free = DIV_ROUND_UP(1300 * (clk / 1000000), 1000); 747 } else { 748 /* normal mode */ 749 low_count = DIV_ROUND_CLOSEST(divider * 47, (47 + 40)); 750 high_count = DIV_ROUND_CLOSEST(divider * 40, (47 + 40)); 751 leadin = DIV_ROUND_UP(4700 * (clk / 1000000), 1000); 752 bus_free = DIV_ROUND_UP(4700 * (clk / 1000000), 1000); 753 } 754 rcv_count = high_count * 3 / 8; 755 xmit_count = low_count * 3 / 8; 756 757 dev_dbg(dev, 758 "speed=%u(actual %u) divider=%u low=%u high=%u xmit=%u rcv=%u leadin=%u bus_free=%u\n", 759 speed, clk / divider, divider, low_count, high_count, 760 xmit_count, rcv_count, leadin, bus_free); 761 762 low_count -= 2; 763 high_count -= 7; 764 i2c->timing0 = (high_count << 16) | rcv_count; 765 i2c->timing1 = (low_count << 16) | xmit_count; 766 i2c->timing2 = (bus_free << 16 | leadin); 767} 768 769static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c) 770{ 771 uint32_t speed; 772 struct device *dev = i2c->dev; 773 struct device_node *node = dev->of_node; 774 int ret; 775 776 ret = of_property_read_u32(node, "clock-frequency", &speed); 777 if (ret) { 778 dev_warn(dev, "No I2C speed selected, using 100kHz\n"); 779 speed = 100000; 780 } 781 782 mxs_i2c_derive_timing(i2c, speed); 783 784 return 0; 785} 786 787static struct platform_device_id mxs_i2c_devtype[] = { 788 { 789 .name = "imx23-i2c", 790 .driver_data = MXS_I2C_V1, 791 }, { 792 .name = "imx28-i2c", 793 .driver_data = MXS_I2C_V2, 794 }, { /* sentinel */ } 795}; 796MODULE_DEVICE_TABLE(platform, mxs_i2c_devtype); 797 798static const struct of_device_id mxs_i2c_dt_ids[] = { 799 { .compatible = "fsl,imx23-i2c", .data = &mxs_i2c_devtype[0], }, 800 { .compatible = "fsl,imx28-i2c", .data = &mxs_i2c_devtype[1], }, 801 { /* sentinel */ } 802}; 803MODULE_DEVICE_TABLE(of, mxs_i2c_dt_ids); 804 805static int mxs_i2c_probe(struct platform_device *pdev) 806{ 807 const struct of_device_id *of_id = 808 of_match_device(mxs_i2c_dt_ids, &pdev->dev); 809 struct device *dev = &pdev->dev; 810 struct mxs_i2c_dev *i2c; 811 struct i2c_adapter *adap; 812 struct resource *res; 813 int err, irq; 814 815 i2c = devm_kzalloc(dev, sizeof(*i2c), GFP_KERNEL); 816 if (!i2c) 817 return -ENOMEM; 818 819 if (of_id) { 820 const struct platform_device_id *device_id = of_id->data; 821 i2c->dev_type = device_id->driver_data; 822 } 823 824 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 825 i2c->regs = devm_ioremap_resource(&pdev->dev, res); 826 if (IS_ERR(i2c->regs)) 827 return PTR_ERR(i2c->regs); 828 829 irq = platform_get_irq(pdev, 0); 830 if (irq < 0) 831 return irq; 832 833 err = devm_request_irq(dev, irq, mxs_i2c_isr, 0, dev_name(dev), i2c); 834 if (err) 835 return err; 836 837 i2c->dev = dev; 838 839 init_completion(&i2c->cmd_complete); 840 841 if (dev->of_node) { 842 err = mxs_i2c_get_ofdata(i2c); 843 if (err) 844 return err; 845 } 846 847 /* Setup the DMA */ 848 i2c->dmach = dma_request_slave_channel(dev, "rx-tx"); 849 if (!i2c->dmach) { 850 dev_err(dev, "Failed to request dma\n"); 851 return -ENODEV; 852 } 853 854 platform_set_drvdata(pdev, i2c); 855 856 /* Do reset to enforce correct startup after pinmuxing */ 857 err = mxs_i2c_reset(i2c); 858 if (err) 859 return err; 860 861 adap = &i2c->adapter; 862 strlcpy(adap->name, "MXS I2C adapter", sizeof(adap->name)); 863 adap->owner = THIS_MODULE; 864 adap->algo = &mxs_i2c_algo; 865 adap->dev.parent = dev; 866 adap->nr = pdev->id; 867 adap->dev.of_node = pdev->dev.of_node; 868 i2c_set_adapdata(adap, i2c); 869 err = i2c_add_numbered_adapter(adap); 870 if (err) { 871 dev_err(dev, "Failed to add adapter (%d)\n", err); 872 writel(MXS_I2C_CTRL0_SFTRST, 873 i2c->regs + MXS_I2C_CTRL0_SET); 874 return err; 875 } 876 877 return 0; 878} 879 880static int mxs_i2c_remove(struct platform_device *pdev) 881{ 882 struct mxs_i2c_dev *i2c = platform_get_drvdata(pdev); 883 884 i2c_del_adapter(&i2c->adapter); 885 886 if (i2c->dmach) 887 dma_release_channel(i2c->dmach); 888 889 writel(MXS_I2C_CTRL0_SFTRST, i2c->regs + MXS_I2C_CTRL0_SET); 890 891 return 0; 892} 893 894static struct platform_driver mxs_i2c_driver = { 895 .driver = { 896 .name = DRIVER_NAME, 897 .of_match_table = mxs_i2c_dt_ids, 898 }, 899 .probe = mxs_i2c_probe, 900 .remove = mxs_i2c_remove, 901}; 902 903static int __init mxs_i2c_init(void) 904{ 905 return platform_driver_register(&mxs_i2c_driver); 906} 907subsys_initcall(mxs_i2c_init); 908 909static void __exit mxs_i2c_exit(void) 910{ 911 platform_driver_unregister(&mxs_i2c_driver); 912} 913module_exit(mxs_i2c_exit); 914 915MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); 916MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>"); 917MODULE_DESCRIPTION("MXS I2C Bus Driver"); 918MODULE_LICENSE("GPL"); 919MODULE_ALIAS("platform:" DRIVER_NAME); 920