1/** 2 * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver 3 * 4 * Copyright (C) 2013 Samsung Electronics Co., Ltd. 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9*/ 10 11#include <linux/kernel.h> 12#include <linux/module.h> 13 14#include <linux/i2c.h> 15#include <linux/time.h> 16#include <linux/interrupt.h> 17#include <linux/delay.h> 18#include <linux/errno.h> 19#include <linux/err.h> 20#include <linux/platform_device.h> 21#include <linux/clk.h> 22#include <linux/slab.h> 23#include <linux/io.h> 24#include <linux/of_address.h> 25#include <linux/of_irq.h> 26#include <linux/spinlock.h> 27 28/* 29 * HSI2C controller from Samsung supports 2 modes of operation 30 * 1. Auto mode: Where in master automatically controls the whole transaction 31 * 2. Manual mode: Software controls the transaction by issuing commands 32 * START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register. 33 * 34 * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register 35 * 36 * Special bits are available for both modes of operation to set commands 37 * and for checking transfer status 38 */ 39 40/* Register Map */ 41#define HSI2C_CTL 0x00 42#define HSI2C_FIFO_CTL 0x04 43#define HSI2C_TRAILIG_CTL 0x08 44#define HSI2C_CLK_CTL 0x0C 45#define HSI2C_CLK_SLOT 0x10 46#define HSI2C_INT_ENABLE 0x20 47#define HSI2C_INT_STATUS 0x24 48#define HSI2C_ERR_STATUS 0x2C 49#define HSI2C_FIFO_STATUS 0x30 50#define HSI2C_TX_DATA 0x34 51#define HSI2C_RX_DATA 0x38 52#define HSI2C_CONF 0x40 53#define HSI2C_AUTO_CONF 0x44 54#define HSI2C_TIMEOUT 0x48 55#define HSI2C_MANUAL_CMD 0x4C 56#define HSI2C_TRANS_STATUS 0x50 57#define HSI2C_TIMING_HS1 0x54 58#define HSI2C_TIMING_HS2 0x58 59#define HSI2C_TIMING_HS3 0x5C 60#define HSI2C_TIMING_FS1 0x60 61#define HSI2C_TIMING_FS2 0x64 62#define HSI2C_TIMING_FS3 0x68 63#define HSI2C_TIMING_SLA 0x6C 64#define HSI2C_ADDR 0x70 65 66/* I2C_CTL Register bits */ 67#define HSI2C_FUNC_MODE_I2C (1u << 0) 68#define HSI2C_MASTER (1u << 3) 69#define HSI2C_RXCHON (1u << 6) 70#define HSI2C_TXCHON (1u << 7) 71#define HSI2C_SW_RST (1u << 31) 72 73/* I2C_FIFO_CTL Register bits */ 74#define HSI2C_RXFIFO_EN (1u << 0) 75#define HSI2C_TXFIFO_EN (1u << 1) 76#define HSI2C_RXFIFO_TRIGGER_LEVEL(x) ((x) << 4) 77#define HSI2C_TXFIFO_TRIGGER_LEVEL(x) ((x) << 16) 78 79/* I2C_TRAILING_CTL Register bits */ 80#define HSI2C_TRAILING_COUNT (0xf) 81 82/* I2C_INT_EN Register bits */ 83#define HSI2C_INT_TX_ALMOSTEMPTY_EN (1u << 0) 84#define HSI2C_INT_RX_ALMOSTFULL_EN (1u << 1) 85#define HSI2C_INT_TRAILING_EN (1u << 6) 86 87/* I2C_INT_STAT Register bits */ 88#define HSI2C_INT_TX_ALMOSTEMPTY (1u << 0) 89#define HSI2C_INT_RX_ALMOSTFULL (1u << 1) 90#define HSI2C_INT_TX_UNDERRUN (1u << 2) 91#define HSI2C_INT_TX_OVERRUN (1u << 3) 92#define HSI2C_INT_RX_UNDERRUN (1u << 4) 93#define HSI2C_INT_RX_OVERRUN (1u << 5) 94#define HSI2C_INT_TRAILING (1u << 6) 95#define HSI2C_INT_I2C (1u << 9) 96 97#define HSI2C_INT_TRANS_DONE (1u << 7) 98#define HSI2C_INT_TRANS_ABORT (1u << 8) 99#define HSI2C_INT_NO_DEV_ACK (1u << 9) 100#define HSI2C_INT_NO_DEV (1u << 10) 101#define HSI2C_INT_TIMEOUT (1u << 11) 102#define HSI2C_INT_I2C_TRANS (HSI2C_INT_TRANS_DONE | \ 103 HSI2C_INT_TRANS_ABORT | \ 104 HSI2C_INT_NO_DEV_ACK | \ 105 HSI2C_INT_NO_DEV | \ 106 HSI2C_INT_TIMEOUT) 107 108/* I2C_FIFO_STAT Register bits */ 109#define HSI2C_RX_FIFO_EMPTY (1u << 24) 110#define HSI2C_RX_FIFO_FULL (1u << 23) 111#define HSI2C_RX_FIFO_LVL(x) ((x >> 16) & 0x7f) 112#define HSI2C_TX_FIFO_EMPTY (1u << 8) 113#define HSI2C_TX_FIFO_FULL (1u << 7) 114#define HSI2C_TX_FIFO_LVL(x) ((x >> 0) & 0x7f) 115 116/* I2C_CONF Register bits */ 117#define HSI2C_AUTO_MODE (1u << 31) 118#define HSI2C_10BIT_ADDR_MODE (1u << 30) 119#define HSI2C_HS_MODE (1u << 29) 120 121/* I2C_AUTO_CONF Register bits */ 122#define HSI2C_READ_WRITE (1u << 16) 123#define HSI2C_STOP_AFTER_TRANS (1u << 17) 124#define HSI2C_MASTER_RUN (1u << 31) 125 126/* I2C_TIMEOUT Register bits */ 127#define HSI2C_TIMEOUT_EN (1u << 31) 128#define HSI2C_TIMEOUT_MASK 0xff 129 130/* I2C_TRANS_STATUS register bits */ 131#define HSI2C_MASTER_BUSY (1u << 17) 132#define HSI2C_SLAVE_BUSY (1u << 16) 133#define HSI2C_TIMEOUT_AUTO (1u << 4) 134#define HSI2C_NO_DEV (1u << 3) 135#define HSI2C_NO_DEV_ACK (1u << 2) 136#define HSI2C_TRANS_ABORT (1u << 1) 137#define HSI2C_TRANS_DONE (1u << 0) 138 139/* I2C_ADDR register bits */ 140#define HSI2C_SLV_ADDR_SLV(x) ((x & 0x3ff) << 0) 141#define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10) 142#define HSI2C_MASTER_ID(x) ((x & 0xff) << 24) 143#define MASTER_ID(x) ((x & 0x7) + 0x08) 144 145/* 146 * Controller operating frequency, timing values for operation 147 * are calculated against this frequency 148 */ 149#define HSI2C_HS_TX_CLOCK 1000000 150#define HSI2C_FS_TX_CLOCK 100000 151#define HSI2C_HIGH_SPD 1 152#define HSI2C_FAST_SPD 0 153 154#define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000)) 155 156#define HSI2C_EXYNOS7 BIT(0) 157 158struct exynos5_i2c { 159 struct i2c_adapter adap; 160 unsigned int suspended:1; 161 162 struct i2c_msg *msg; 163 struct completion msg_complete; 164 unsigned int msg_ptr; 165 166 unsigned int irq; 167 168 void __iomem *regs; 169 struct clk *clk; 170 struct device *dev; 171 int state; 172 173 spinlock_t lock; /* IRQ synchronization */ 174 175 /* 176 * Since the TRANS_DONE bit is cleared on read, and we may read it 177 * either during an IRQ or after a transaction, keep track of its 178 * state here. 179 */ 180 int trans_done; 181 182 /* Controller operating frequency */ 183 unsigned int fs_clock; 184 unsigned int hs_clock; 185 186 /* 187 * HSI2C Controller can operate in 188 * 1. High speed upto 3.4Mbps 189 * 2. Fast speed upto 1Mbps 190 */ 191 int speed_mode; 192 193 /* Version of HS-I2C Hardware */ 194 struct exynos_hsi2c_variant *variant; 195}; 196 197/** 198 * struct exynos_hsi2c_variant - platform specific HSI2C driver data 199 * @fifo_depth: the fifo depth supported by the HSI2C module 200 * 201 * Specifies platform specific configuration of HSI2C module. 202 * Note: A structure for driver specific platform data is used for future 203 * expansion of its usage. 204 */ 205struct exynos_hsi2c_variant { 206 unsigned int fifo_depth; 207 unsigned int hw; 208}; 209 210static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = { 211 .fifo_depth = 64, 212}; 213 214static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = { 215 .fifo_depth = 16, 216}; 217 218static const struct exynos_hsi2c_variant exynos7_hsi2c_data = { 219 .fifo_depth = 16, 220 .hw = HSI2C_EXYNOS7, 221}; 222 223static const struct of_device_id exynos5_i2c_match[] = { 224 { 225 .compatible = "samsung,exynos5-hsi2c", 226 .data = &exynos5250_hsi2c_data 227 }, { 228 .compatible = "samsung,exynos5250-hsi2c", 229 .data = &exynos5250_hsi2c_data 230 }, { 231 .compatible = "samsung,exynos5260-hsi2c", 232 .data = &exynos5260_hsi2c_data 233 }, { 234 .compatible = "samsung,exynos7-hsi2c", 235 .data = &exynos7_hsi2c_data 236 }, {}, 237}; 238MODULE_DEVICE_TABLE(of, exynos5_i2c_match); 239 240static inline struct exynos_hsi2c_variant *exynos5_i2c_get_variant 241 (struct platform_device *pdev) 242{ 243 const struct of_device_id *match; 244 245 match = of_match_node(exynos5_i2c_match, pdev->dev.of_node); 246 return (struct exynos_hsi2c_variant *)match->data; 247} 248 249static void exynos5_i2c_clr_pend_irq(struct exynos5_i2c *i2c) 250{ 251 writel(readl(i2c->regs + HSI2C_INT_STATUS), 252 i2c->regs + HSI2C_INT_STATUS); 253} 254 255/* 256 * exynos5_i2c_set_timing: updates the registers with appropriate 257 * timing values calculated 258 * 259 * Returns 0 on success, -EINVAL if the cycle length cannot 260 * be calculated. 261 */ 262static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, int mode) 263{ 264 u32 i2c_timing_s1; 265 u32 i2c_timing_s2; 266 u32 i2c_timing_s3; 267 u32 i2c_timing_sla; 268 unsigned int t_start_su, t_start_hd; 269 unsigned int t_stop_su; 270 unsigned int t_data_su, t_data_hd; 271 unsigned int t_scl_l, t_scl_h; 272 unsigned int t_sr_release; 273 unsigned int t_ftl_cycle; 274 unsigned int clkin = clk_get_rate(i2c->clk); 275 unsigned int div, utemp0 = 0, utemp1 = 0, clk_cycle; 276 unsigned int op_clk = (mode == HSI2C_HIGH_SPD) ? 277 i2c->hs_clock : i2c->fs_clock; 278 279 /* 280 * In case of HSI2C controller in Exynos5 series 281 * FPCLK / FI2C = 282 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE 283 * 284 * In case of HSI2C controllers in Exynos7 series 285 * FPCLK / FI2C = 286 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + FLT_CYCLE 287 * 288 * utemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) 289 * utemp1 = (TSCLK_L + TSCLK_H + 2) 290 */ 291 t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7; 292 utemp0 = (clkin / op_clk) - 8; 293 294 if (i2c->variant->hw == HSI2C_EXYNOS7) 295 utemp0 -= t_ftl_cycle; 296 else 297 utemp0 -= 2 * t_ftl_cycle; 298 299 /* CLK_DIV max is 256 */ 300 for (div = 0; div < 256; div++) { 301 utemp1 = utemp0 / (div + 1); 302 303 /* 304 * SCL_L and SCL_H each has max value of 255 305 * Hence, For the clk_cycle to the have right value 306 * utemp1 has to be less then 512 and more than 4. 307 */ 308 if ((utemp1 < 512) && (utemp1 > 4)) { 309 clk_cycle = utemp1 - 2; 310 break; 311 } else if (div == 255) { 312 dev_warn(i2c->dev, "Failed to calculate divisor"); 313 return -EINVAL; 314 } 315 } 316 317 t_scl_l = clk_cycle / 2; 318 t_scl_h = clk_cycle / 2; 319 t_start_su = t_scl_l; 320 t_start_hd = t_scl_l; 321 t_stop_su = t_scl_l; 322 t_data_su = t_scl_l / 2; 323 t_data_hd = t_scl_l / 2; 324 t_sr_release = clk_cycle; 325 326 i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8; 327 i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0; 328 i2c_timing_s3 = div << 16 | t_sr_release << 0; 329 i2c_timing_sla = t_data_hd << 0; 330 331 dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n", 332 t_start_su, t_start_hd, t_stop_su); 333 dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n", 334 t_data_su, t_scl_l, t_scl_h); 335 dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n", 336 div, t_sr_release); 337 dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd); 338 339 if (mode == HSI2C_HIGH_SPD) { 340 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1); 341 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2); 342 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3); 343 } else { 344 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1); 345 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2); 346 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3); 347 } 348 writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA); 349 350 return 0; 351} 352 353static int exynos5_hsi2c_clock_setup(struct exynos5_i2c *i2c) 354{ 355 /* 356 * Configure the Fast speed timing values 357 * Even the High Speed mode initially starts with Fast mode 358 */ 359 if (exynos5_i2c_set_timing(i2c, HSI2C_FAST_SPD)) { 360 dev_err(i2c->dev, "HSI2C FS Clock set up failed\n"); 361 return -EINVAL; 362 } 363 364 /* configure the High speed timing values */ 365 if (i2c->speed_mode == HSI2C_HIGH_SPD) { 366 if (exynos5_i2c_set_timing(i2c, HSI2C_HIGH_SPD)) { 367 dev_err(i2c->dev, "HSI2C HS Clock set up failed\n"); 368 return -EINVAL; 369 } 370 } 371 372 return 0; 373} 374 375/* 376 * exynos5_i2c_init: configures the controller for I2C functionality 377 * Programs I2C controller for Master mode operation 378 */ 379static void exynos5_i2c_init(struct exynos5_i2c *i2c) 380{ 381 u32 i2c_conf = readl(i2c->regs + HSI2C_CONF); 382 u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT); 383 384 /* Clear to disable Timeout */ 385 i2c_timeout &= ~HSI2C_TIMEOUT_EN; 386 writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT); 387 388 writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER), 389 i2c->regs + HSI2C_CTL); 390 writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL); 391 392 if (i2c->speed_mode == HSI2C_HIGH_SPD) { 393 writel(HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)), 394 i2c->regs + HSI2C_ADDR); 395 i2c_conf |= HSI2C_HS_MODE; 396 } 397 398 writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF); 399} 400 401static void exynos5_i2c_reset(struct exynos5_i2c *i2c) 402{ 403 u32 i2c_ctl; 404 405 /* Set and clear the bit for reset */ 406 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 407 i2c_ctl |= HSI2C_SW_RST; 408 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 409 410 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 411 i2c_ctl &= ~HSI2C_SW_RST; 412 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 413 414 /* We don't expect calculations to fail during the run */ 415 exynos5_hsi2c_clock_setup(i2c); 416 /* Initialize the configure registers */ 417 exynos5_i2c_init(i2c); 418} 419 420/* 421 * exynos5_i2c_irq: top level IRQ servicing routine 422 * 423 * INT_STATUS registers gives the interrupt details. Further, 424 * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed 425 * state of the bus. 426 */ 427static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id) 428{ 429 struct exynos5_i2c *i2c = dev_id; 430 u32 fifo_level, int_status, fifo_status, trans_status; 431 unsigned char byte; 432 int len = 0; 433 434 i2c->state = -EINVAL; 435 436 spin_lock(&i2c->lock); 437 438 int_status = readl(i2c->regs + HSI2C_INT_STATUS); 439 writel(int_status, i2c->regs + HSI2C_INT_STATUS); 440 441 /* handle interrupt related to the transfer status */ 442 if (i2c->variant->hw == HSI2C_EXYNOS7) { 443 if (int_status & HSI2C_INT_TRANS_DONE) { 444 i2c->trans_done = 1; 445 i2c->state = 0; 446 } else if (int_status & HSI2C_INT_TRANS_ABORT) { 447 dev_dbg(i2c->dev, "Deal with arbitration lose\n"); 448 i2c->state = -EAGAIN; 449 goto stop; 450 } else if (int_status & HSI2C_INT_NO_DEV_ACK) { 451 dev_dbg(i2c->dev, "No ACK from device\n"); 452 i2c->state = -ENXIO; 453 goto stop; 454 } else if (int_status & HSI2C_INT_NO_DEV) { 455 dev_dbg(i2c->dev, "No device\n"); 456 i2c->state = -ENXIO; 457 goto stop; 458 } else if (int_status & HSI2C_INT_TIMEOUT) { 459 dev_dbg(i2c->dev, "Accessing device timed out\n"); 460 i2c->state = -ETIMEDOUT; 461 goto stop; 462 } 463 } else if (int_status & HSI2C_INT_I2C) { 464 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 465 if (trans_status & HSI2C_NO_DEV_ACK) { 466 dev_dbg(i2c->dev, "No ACK from device\n"); 467 i2c->state = -ENXIO; 468 goto stop; 469 } else if (trans_status & HSI2C_NO_DEV) { 470 dev_dbg(i2c->dev, "No device\n"); 471 i2c->state = -ENXIO; 472 goto stop; 473 } else if (trans_status & HSI2C_TRANS_ABORT) { 474 dev_dbg(i2c->dev, "Deal with arbitration lose\n"); 475 i2c->state = -EAGAIN; 476 goto stop; 477 } else if (trans_status & HSI2C_TIMEOUT_AUTO) { 478 dev_dbg(i2c->dev, "Accessing device timed out\n"); 479 i2c->state = -ETIMEDOUT; 480 goto stop; 481 } else if (trans_status & HSI2C_TRANS_DONE) { 482 i2c->trans_done = 1; 483 i2c->state = 0; 484 } 485 } 486 487 if ((i2c->msg->flags & I2C_M_RD) && (int_status & 488 (HSI2C_INT_TRAILING | HSI2C_INT_RX_ALMOSTFULL))) { 489 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 490 fifo_level = HSI2C_RX_FIFO_LVL(fifo_status); 491 len = min(fifo_level, i2c->msg->len - i2c->msg_ptr); 492 493 while (len > 0) { 494 byte = (unsigned char) 495 readl(i2c->regs + HSI2C_RX_DATA); 496 i2c->msg->buf[i2c->msg_ptr++] = byte; 497 len--; 498 } 499 i2c->state = 0; 500 } else if (int_status & HSI2C_INT_TX_ALMOSTEMPTY) { 501 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS); 502 fifo_level = HSI2C_TX_FIFO_LVL(fifo_status); 503 504 len = i2c->variant->fifo_depth - fifo_level; 505 if (len > (i2c->msg->len - i2c->msg_ptr)) 506 len = i2c->msg->len - i2c->msg_ptr; 507 508 while (len > 0) { 509 byte = i2c->msg->buf[i2c->msg_ptr++]; 510 writel(byte, i2c->regs + HSI2C_TX_DATA); 511 len--; 512 } 513 i2c->state = 0; 514 } 515 516 stop: 517 if ((i2c->trans_done && (i2c->msg->len == i2c->msg_ptr)) || 518 (i2c->state < 0)) { 519 writel(0, i2c->regs + HSI2C_INT_ENABLE); 520 exynos5_i2c_clr_pend_irq(i2c); 521 complete(&i2c->msg_complete); 522 } 523 524 spin_unlock(&i2c->lock); 525 526 return IRQ_HANDLED; 527} 528 529/* 530 * exynos5_i2c_wait_bus_idle 531 * 532 * Wait for the bus to go idle, indicated by the MASTER_BUSY bit being 533 * cleared. 534 * 535 * Returns -EBUSY if the bus cannot be bought to idle 536 */ 537static int exynos5_i2c_wait_bus_idle(struct exynos5_i2c *i2c) 538{ 539 unsigned long stop_time; 540 u32 trans_status; 541 542 /* wait for 100 milli seconds for the bus to be idle */ 543 stop_time = jiffies + msecs_to_jiffies(100) + 1; 544 do { 545 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS); 546 if (!(trans_status & HSI2C_MASTER_BUSY)) 547 return 0; 548 549 usleep_range(50, 200); 550 } while (time_before(jiffies, stop_time)); 551 552 return -EBUSY; 553} 554 555/* 556 * exynos5_i2c_message_start: Configures the bus and starts the xfer 557 * i2c: struct exynos5_i2c pointer for the current bus 558 * stop: Enables stop after transfer if set. Set for last transfer of 559 * in the list of messages. 560 * 561 * Configures the bus for read/write function 562 * Sets chip address to talk to, message length to be sent. 563 * Enables appropriate interrupts and sends start xfer command. 564 */ 565static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop) 566{ 567 u32 i2c_ctl; 568 u32 int_en = 0; 569 u32 i2c_auto_conf = 0; 570 u32 fifo_ctl; 571 unsigned long flags; 572 unsigned short trig_lvl; 573 574 if (i2c->variant->hw == HSI2C_EXYNOS7) 575 int_en |= HSI2C_INT_I2C_TRANS; 576 else 577 int_en |= HSI2C_INT_I2C; 578 579 i2c_ctl = readl(i2c->regs + HSI2C_CTL); 580 i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON); 581 fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN; 582 583 if (i2c->msg->flags & I2C_M_RD) { 584 i2c_ctl |= HSI2C_RXCHON; 585 586 i2c_auto_conf |= HSI2C_READ_WRITE; 587 588 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 589 (i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len; 590 fifo_ctl |= HSI2C_RXFIFO_TRIGGER_LEVEL(trig_lvl); 591 592 int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN | 593 HSI2C_INT_TRAILING_EN); 594 } else { 595 i2c_ctl |= HSI2C_TXCHON; 596 597 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ? 598 (i2c->variant->fifo_depth * 1 / 4) : i2c->msg->len; 599 fifo_ctl |= HSI2C_TXFIFO_TRIGGER_LEVEL(trig_lvl); 600 601 int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN; 602 } 603 604 writel(HSI2C_SLV_ADDR_MAS(i2c->msg->addr), i2c->regs + HSI2C_ADDR); 605 606 writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL); 607 writel(i2c_ctl, i2c->regs + HSI2C_CTL); 608 609 /* 610 * Enable interrupts before starting the transfer so that we don't 611 * miss any INT_I2C interrupts. 612 */ 613 spin_lock_irqsave(&i2c->lock, flags); 614 writel(int_en, i2c->regs + HSI2C_INT_ENABLE); 615 616 if (stop == 1) 617 i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS; 618 i2c_auto_conf |= i2c->msg->len; 619 i2c_auto_conf |= HSI2C_MASTER_RUN; 620 writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF); 621 spin_unlock_irqrestore(&i2c->lock, flags); 622} 623 624static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c, 625 struct i2c_msg *msgs, int stop) 626{ 627 unsigned long timeout; 628 int ret; 629 630 i2c->msg = msgs; 631 i2c->msg_ptr = 0; 632 i2c->trans_done = 0; 633 634 reinit_completion(&i2c->msg_complete); 635 636 exynos5_i2c_message_start(i2c, stop); 637 638 timeout = wait_for_completion_timeout(&i2c->msg_complete, 639 EXYNOS5_I2C_TIMEOUT); 640 if (timeout == 0) 641 ret = -ETIMEDOUT; 642 else 643 ret = i2c->state; 644 645 /* 646 * If this is the last message to be transfered (stop == 1) 647 * Then check if the bus can be brought back to idle. 648 */ 649 if (ret == 0 && stop) 650 ret = exynos5_i2c_wait_bus_idle(i2c); 651 652 if (ret < 0) { 653 exynos5_i2c_reset(i2c); 654 if (ret == -ETIMEDOUT) 655 dev_warn(i2c->dev, "%s timeout\n", 656 (msgs->flags & I2C_M_RD) ? "rx" : "tx"); 657 } 658 659 /* Return the state as in interrupt routine */ 660 return ret; 661} 662 663static int exynos5_i2c_xfer(struct i2c_adapter *adap, 664 struct i2c_msg *msgs, int num) 665{ 666 struct exynos5_i2c *i2c = adap->algo_data; 667 int i = 0, ret = 0, stop = 0; 668 669 if (i2c->suspended) { 670 dev_err(i2c->dev, "HS-I2C is not initialized.\n"); 671 return -EIO; 672 } 673 674 clk_prepare_enable(i2c->clk); 675 676 for (i = 0; i < num; i++, msgs++) { 677 stop = (i == num - 1); 678 679 ret = exynos5_i2c_xfer_msg(i2c, msgs, stop); 680 681 if (ret < 0) 682 goto out; 683 } 684 685 if (i == num) { 686 ret = num; 687 } else { 688 /* Only one message, cannot access the device */ 689 if (i == 1) 690 ret = -EREMOTEIO; 691 else 692 ret = i; 693 694 dev_warn(i2c->dev, "xfer message failed\n"); 695 } 696 697 out: 698 clk_disable_unprepare(i2c->clk); 699 return ret; 700} 701 702static u32 exynos5_i2c_func(struct i2c_adapter *adap) 703{ 704 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); 705} 706 707static const struct i2c_algorithm exynos5_i2c_algorithm = { 708 .master_xfer = exynos5_i2c_xfer, 709 .functionality = exynos5_i2c_func, 710}; 711 712static int exynos5_i2c_probe(struct platform_device *pdev) 713{ 714 struct device_node *np = pdev->dev.of_node; 715 struct exynos5_i2c *i2c; 716 struct resource *mem; 717 unsigned int op_clock; 718 int ret; 719 720 i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL); 721 if (!i2c) 722 return -ENOMEM; 723 724 if (of_property_read_u32(np, "clock-frequency", &op_clock)) { 725 i2c->speed_mode = HSI2C_FAST_SPD; 726 i2c->fs_clock = HSI2C_FS_TX_CLOCK; 727 } else { 728 if (op_clock >= HSI2C_HS_TX_CLOCK) { 729 i2c->speed_mode = HSI2C_HIGH_SPD; 730 i2c->fs_clock = HSI2C_FS_TX_CLOCK; 731 i2c->hs_clock = op_clock; 732 } else { 733 i2c->speed_mode = HSI2C_FAST_SPD; 734 i2c->fs_clock = op_clock; 735 } 736 } 737 738 strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name)); 739 i2c->adap.owner = THIS_MODULE; 740 i2c->adap.algo = &exynos5_i2c_algorithm; 741 i2c->adap.retries = 3; 742 743 i2c->dev = &pdev->dev; 744 i2c->clk = devm_clk_get(&pdev->dev, "hsi2c"); 745 if (IS_ERR(i2c->clk)) { 746 dev_err(&pdev->dev, "cannot get clock\n"); 747 return -ENOENT; 748 } 749 750 clk_prepare_enable(i2c->clk); 751 752 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 753 i2c->regs = devm_ioremap_resource(&pdev->dev, mem); 754 if (IS_ERR(i2c->regs)) { 755 ret = PTR_ERR(i2c->regs); 756 goto err_clk; 757 } 758 759 i2c->adap.dev.of_node = np; 760 i2c->adap.algo_data = i2c; 761 i2c->adap.dev.parent = &pdev->dev; 762 763 /* Clear pending interrupts from u-boot or misc causes */ 764 exynos5_i2c_clr_pend_irq(i2c); 765 766 spin_lock_init(&i2c->lock); 767 init_completion(&i2c->msg_complete); 768 769 i2c->irq = ret = platform_get_irq(pdev, 0); 770 if (ret <= 0) { 771 dev_err(&pdev->dev, "cannot find HS-I2C IRQ\n"); 772 ret = -EINVAL; 773 goto err_clk; 774 } 775 776 ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq, 777 IRQF_NO_SUSPEND | IRQF_ONESHOT, 778 dev_name(&pdev->dev), i2c); 779 780 if (ret != 0) { 781 dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq); 782 goto err_clk; 783 } 784 785 /* Need to check the variant before setting up. */ 786 i2c->variant = exynos5_i2c_get_variant(pdev); 787 788 ret = exynos5_hsi2c_clock_setup(i2c); 789 if (ret) 790 goto err_clk; 791 792 exynos5_i2c_reset(i2c); 793 794 ret = i2c_add_adapter(&i2c->adap); 795 if (ret < 0) { 796 dev_err(&pdev->dev, "failed to add bus to i2c core\n"); 797 goto err_clk; 798 } 799 800 platform_set_drvdata(pdev, i2c); 801 802 err_clk: 803 clk_disable_unprepare(i2c->clk); 804 return ret; 805} 806 807static int exynos5_i2c_remove(struct platform_device *pdev) 808{ 809 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 810 811 i2c_del_adapter(&i2c->adap); 812 813 return 0; 814} 815 816#ifdef CONFIG_PM_SLEEP 817static int exynos5_i2c_suspend_noirq(struct device *dev) 818{ 819 struct platform_device *pdev = to_platform_device(dev); 820 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 821 822 i2c->suspended = 1; 823 824 return 0; 825} 826 827static int exynos5_i2c_resume_noirq(struct device *dev) 828{ 829 struct platform_device *pdev = to_platform_device(dev); 830 struct exynos5_i2c *i2c = platform_get_drvdata(pdev); 831 int ret = 0; 832 833 clk_prepare_enable(i2c->clk); 834 835 ret = exynos5_hsi2c_clock_setup(i2c); 836 if (ret) { 837 clk_disable_unprepare(i2c->clk); 838 return ret; 839 } 840 841 exynos5_i2c_init(i2c); 842 clk_disable_unprepare(i2c->clk); 843 i2c->suspended = 0; 844 845 return 0; 846} 847#endif 848 849static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = { 850#ifdef CONFIG_PM_SLEEP 851 .suspend_noirq = exynos5_i2c_suspend_noirq, 852 .resume_noirq = exynos5_i2c_resume_noirq, 853 .freeze_noirq = exynos5_i2c_suspend_noirq, 854 .thaw_noirq = exynos5_i2c_resume_noirq, 855 .poweroff_noirq = exynos5_i2c_suspend_noirq, 856 .restore_noirq = exynos5_i2c_resume_noirq, 857#endif 858}; 859 860static struct platform_driver exynos5_i2c_driver = { 861 .probe = exynos5_i2c_probe, 862 .remove = exynos5_i2c_remove, 863 .driver = { 864 .name = "exynos5-hsi2c", 865 .pm = &exynos5_i2c_dev_pm_ops, 866 .of_match_table = exynos5_i2c_match, 867 }, 868}; 869 870module_platform_driver(exynos5_i2c_driver); 871 872MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver"); 873MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>"); 874MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>"); 875MODULE_LICENSE("GPL v2"); 876