1/dts-v1/;
2
3#include "kirkwood.dtsi"
4#include "kirkwood-6281.dtsi"
5
6/ {
7	model = "Seagate GoFlex Net";
8	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
9
10	memory {
11		device_type = "memory";
12		reg = <0x00000000 0x8000000>;
13	};
14
15	chosen {
16		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
17		stdout-path = &uart0;
18	};
19
20	ocp@f1000000 {
21		pinctrl: pin-controller@10000 {
22			pmx_usb_power_enable: pmx-usb-power-enable {
23				marvell,pins = "mpp29";
24				marvell,function = "gpio";
25			};
26			pmx_led_right_cap_0: pmx-led_right_cap_0 {
27				marvell,pins = "mpp38";
28				marvell,function = "gpio";
29			};
30			pmx_led_right_cap_1: pmx-led_right_cap_1 {
31				marvell,pins = "mpp39";
32				marvell,function = "gpio";
33			};
34			pmx_led_right_cap_2: pmx-led_right_cap_2 {
35				marvell,pins = "mpp40";
36				marvell,function = "gpio";
37			};
38			pmx_led_right_cap_3: pmx-led_right_cap_3 {
39				marvell,pins = "mpp41";
40				marvell,function = "gpio";
41			};
42			pmx_led_left_cap_0: pmx-led_left_cap_0 {
43				marvell,pins = "mpp42";
44				marvell,function = "gpio";
45			};
46			pmx_led_left_cap_1: pmx-led_left_cap_1 {
47				marvell,pins = "mpp43";
48				marvell,function = "gpio";
49			};
50			pmx_led_left_cap_2: pmx-led_left_cap_2 {
51				marvell,pins = "mpp44";
52				marvell,function = "gpio";
53			};
54			pmx_led_left_cap_3: pmx-led_left_cap_3 {
55				marvell,pins = "mpp45";
56				marvell,function = "gpio";
57			};
58			pmx_led_green: pmx-led_green {
59				marvell,pins = "mpp46";
60				marvell,function = "gpio";
61			};
62			pmx_led_orange: pmx-led_orange {
63				marvell,pins = "mpp47";
64				marvell,function = "gpio";
65			};
66		};
67		serial@12000 {
68			status = "ok";
69		};
70
71		sata@80000 {
72			status = "okay";
73			nr-ports = <2>;
74		};
75
76	};
77	gpio-leds {
78		compatible = "gpio-leds";
79		pinctrl-0 = < &pmx_led_orange
80			      &pmx_led_left_cap_0 &pmx_led_left_cap_1
81			      &pmx_led_left_cap_2 &pmx_led_left_cap_3
82			      &pmx_led_right_cap_0 &pmx_led_right_cap_1
83			      &pmx_led_right_cap_2 &pmx_led_right_cap_3
84			    >;
85		pinctrl-names = "default";
86
87		health {
88			label = "status:green:health";
89			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
90			default-state = "keep";
91		};
92		fault {
93			label = "status:orange:fault";
94			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
95		};
96		left0 {
97			label = "status:white:left0";
98			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
99		};
100		left1 {
101			label = "status:white:left1";
102			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
103		};
104		left2 {
105			label = "status:white:left2";
106			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
107		};
108		left3 {
109			label = "status:white:left3";
110			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
111		};
112		right0 {
113			label = "status:white:right0";
114			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
115		};
116		right1 {
117			label = "status:white:right1";
118			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
119		};
120		right2 {
121			label = "status:white:right2";
122			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
123		};
124		right3 {
125			label = "status:white:right3";
126			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
127		};
128	};
129	regulators {
130		compatible = "simple-bus";
131		#address-cells = <1>;
132		#size-cells = <0>;
133		pinctrl-0 = <&pmx_usb_power_enable>;
134		pinctrl-names = "default";
135
136		usb_power: regulator@1 {
137			compatible = "regulator-fixed";
138			reg = <1>;
139			regulator-name = "USB Power";
140			regulator-min-microvolt = <5000000>;
141			regulator-max-microvolt = <5000000>;
142			enable-active-high;
143			regulator-always-on;
144			regulator-boot-on;
145			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
146		};
147	};
148};
149
150&nand {
151	chip-delay = <40>;
152	status = "okay";
153
154	partition@0 {
155		label = "u-boot";
156		reg = <0x0000000 0x100000>;
157		read-only;
158	};
159
160	partition@100000 {
161		label = "uImage";
162		reg = <0x0100000 0x400000>;
163	};
164
165	partition@500000 {
166		label = "pogoplug";
167		reg = <0x0500000 0x2000000>;
168	};
169
170	partition@2500000 {
171		label = "root";
172		reg = <0x02500000 0xd800000>;
173	};
174};
175
176&mdio {
177	status = "okay";
178
179	ethphy0: ethernet-phy@0 {
180		reg = <0>;
181	};
182};
183
184&eth0 {
185	status = "okay";
186	ethernet0-port@0 {
187		phy-handle = <&ethphy0>;
188	};
189};
190