1The Exynos display port interface should be configured based on
2the type of panel connected to it.
3
4We use two nodes:
5	-dp-controller node
6	-dptx-phy node(defined inside dp-controller node)
7
8For the DP-PHY initialization, we use the dptx-phy node.
9Required properties for dptx-phy: deprecated, use phys and phy-names
10	-reg: deprecated
11		Base address of DP PHY register.
12	-samsung,enable-mask: deprecated
13		The bit-mask used to enable/disable DP PHY.
14
15For the Panel initialization, we read data from dp-controller node.
16Required properties for dp-controller:
17	-compatible:
18		should be "samsung,exynos5-dp".
19	-reg:
20		physical base address of the controller and length
21		of memory mapped region.
22	-interrupts:
23		interrupt combiner values.
24	-clocks:
25		from common clock binding: handle to dp clock.
26	-clock-names:
27		from common clock binding: Shall be "dp".
28	-interrupt-parent:
29		phandle to Interrupt combiner node.
30	-phys:
31		from general PHY binding: the phandle for the PHY device.
32	-phy-names:
33		from general PHY binding: Should be "dp".
34	-samsung,color-space:
35		input video data format.
36			COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
37	-samsung,dynamic-range:
38		dynamic range for input video data.
39			VESA = 0, CEA = 1
40	-samsung,ycbcr-coeff:
41		YCbCr co-efficients for input video.
42			COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
43	-samsung,color-depth:
44		number of bits per colour component.
45			COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
46	-samsung,link-rate:
47		link rate supported by the panel.
48			LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
49	-samsung,lane-count:
50		number of lanes supported by the panel.
51			LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
52	- display-timings: timings for the connected panel as described by
53		Documentation/devicetree/bindings/video/display-timing.txt
54
55Optional properties for dp-controller:
56	-interlaced:
57		interlace scan mode.
58			Progressive if defined, Interlaced if not defined
59	-vsync-active-high:
60		VSYNC polarity configuration.
61			High if defined, Low if not defined
62	-hsync-active-high:
63		HSYNC polarity configuration.
64			High if defined, Low if not defined
65	-samsung,hpd-gpio:
66		Hotplug detect GPIO.
67			Indicates which GPIO should be used for hotplug
68			detection
69	-video interfaces: Device node can contain video interface port
70			    nodes according to [1].
71
72[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
73
74Example:
75
76SOC specific portion:
77	dp-controller {
78		compatible = "samsung,exynos5-dp";
79		reg = <0x145b0000 0x10000>;
80		interrupts = <10 3>;
81		interrupt-parent = <&combiner>;
82		clocks = <&clock 342>;
83		clock-names = "dp";
84
85		phys = <&dp_phy>;
86		phy-names = "dp";
87	};
88
89Board Specific portion:
90	dp-controller {
91		samsung,color-space = <0>;
92		samsung,dynamic-range = <0>;
93		samsung,ycbcr-coeff = <0>;
94		samsung,color-depth = <1>;
95		samsung,link-rate = <0x0a>;
96		samsung,lane-count = <4>;
97
98		display-timings {
99			native-mode = <&lcd_timing>;
100			lcd_timing: 1366x768 {
101				clock-frequency = <70589280>;
102				hactive = <1366>;
103				vactive = <768>;
104				hfront-porch = <40>;
105				hback-porch = <40>;
106				hsync-len = <32>;
107				vback-porch = <10>;
108				vfront-porch = <12>;
109				vsync-len = <6>;
110			};
111		};
112
113		ports {
114			port@0 {
115				dp_out: endpoint {
116					remote-endpoint = <&bridge_in>;
117				};
118			};
119		};
120	};
121