1Bosch MCAN controller Device Tree Bindings
2-------------------------------------------------
3
4Required properties:
5- compatible		: Should be "bosch,m_can" for M_CAN controllers
6- reg			: physical base address and size of the M_CAN
7			  registers map and Message RAM
8- reg-names		: Should be "m_can" and "message_ram"
9- interrupts		: Should be the interrupt number of M_CAN interrupt
10			  line 0 and line 1, could be same if sharing
11			  the same interrupt.
12- interrupt-names	: Should contain "int0" and "int1"
13- clocks		: Clocks used by controller, should be host clock
14			  and CAN clock.
15- clock-names		: Should contain "hclk" and "cclk"
16- pinctrl-<n>		: Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt
17- pinctrl-names 	: Names corresponding to the numbered pinctrl states
18- bosch,mram-cfg	: Message RAM configuration data.
19			  Multiple M_CAN instances can share the same Message
20			  RAM and each element(e.g Rx FIFO or Tx Buffer and etc)
21			  number in Message RAM is also configurable,
22			  so this property is telling driver how the shared or
23			  private Message RAM are used by this M_CAN controller.
24
25			  The format should be as follows:
26			  <offset sidf_elems xidf_elems rxf0_elems rxf1_elems
27			   rxb_elems txe_elems txb_elems>
28			  The 'offset' is an address offset of the Message RAM
29			  where the following elements start from. This is
30			  usually set to 0x0 if you're using a private Message
31			  RAM. The remain cells are used to specify how many
32			  elements are used for each FIFO/Buffer.
33
34			  M_CAN includes the following elements according to user manual:
35			  11-bit Filter	0-128 elements / 0-128 words
36			  29-bit Filter	0-64 elements / 0-128 words
37			  Rx FIFO 0	0-64 elements / 0-1152 words
38			  Rx FIFO 1	0-64 elements / 0-1152 words
39			  Rx Buffers	0-64 elements / 0-1152 words
40			  Tx Event FIFO	0-32 elements / 0-64 words
41			  Tx Buffers	0-32 elements / 0-576 words
42
43			  Please refer to 2.4.1 Message RAM Configuration in
44			  Bosch M_CAN user manual for details.
45
46Example:
47SoC dtsi:
48m_can1: can@020e8000 {
49	compatible = "bosch,m_can";
50	reg = <0x020e8000 0x4000>, <0x02298000 0x4000>;
51	reg-names = "m_can", "message_ram";
52	interrupts = <0 114 0x04>,
53		     <0 114 0x04>;
54	interrupt-names = "int0", "int1";
55	clocks = <&clks IMX6SX_CLK_CANFD>,
56		 <&clks IMX6SX_CLK_CANFD>;
57	clock-names = "hclk", "cclk";
58	bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>;
59	status = "disabled";
60};
61
62Board dts:
63&m_can1 {
64	pinctrl-names = "default";
65	pinctrl-0 = <&pinctrl_m_can1>;
66	status = "enabled";
67};
68