Searched refs:impedance (Results 1 – 25 of 25) sorted by relevance
| /linux-4.1.27/arch/arm/boot/dts/ |
| D | zynq-zc702.dts | 172 bias-high-impedance;
195 bias-high-impedance;
279 bias-high-impedance;
292 bias-high-impedance;
313 bias-high-impedance;
336 bias-high-impedance;
|
| D | zynq-zc706.dts | 148 bias-high-impedance;
228 bias-high-impedance;
241 bias-high-impedance;
262 bias-high-impedance;
285 bias-high-impedance;
|
| D | tegra124-nyan.dtsi | 140 bias-high-impedance;
|
| D | tegra124-venice2.dts | 665 bias-high-impedance;
|
| D | tegra124-jetson-tk1.dts | 1449 bias-high-impedance;
|
| /linux-4.1.27/Documentation/hwmon/ |
| D | da9055 | 19 Channel 1: ADC_IN1 - high impedance input (0 - 2.5V)
20 Channel 2: ADC_IN2 - high impedance input (0 - 2.5V)
21 Channel 3: ADC_IN3 - high impedance input (0 - 2.5V)
|
| D | da9052 | 22 Channel 4: ADC_IN4 - high impedance input (0 - 2.5V)
23 Channel 5: ADC_IN5 - high impedance input (0 - 2.5V)
24 Channel 6: ADC_IN6 - high impedance input (0 - 2.5V)
|
| /linux-4.1.27/drivers/staging/iio/ |
| D | Makefile | 18 obj-y += impedance-analyzer/
|
| D | Kconfig | 13 source "drivers/staging/iio/impedance-analyzer/Kconfig"
|
| /linux-4.1.27/Documentation/devicetree/bindings/pinctrl/ |
| D | xlnx,zynq-pinctrl.txt | 40 groups, pins, bias-disable, bias-high-impedance, bias-pull-up, slew-rate,
96 bias-high-impedance;
|
| D | pinctrl-bindings.txt | 178 bias-high-impedance - high impedance mode ("third-state", "floating")
|
| D | img,tz1090-pdc-pinctrl.txt | 41 - bias-high-impedance
|
| D | qcom,pmic-mpp.txt | 101 - bias-high-impedance:
|
| D | qcom,pmic-gpio.txt | 126 - bias-high-impedance:
|
| D | img,tz1090-pinctrl.txt | 41 - bias-high-impedance
|
| /linux-4.1.27/Documentation/devicetree/bindings/phy/ |
| D | phy-miphy28lp.txt | 44 - st,tx-impedance-comp : to compensate tx impedance avoiding out of range values.
|
| /linux-4.1.27/drivers/staging/iio/Documentation/ |
| D | sysfs-bus-iio-impedance-analyzer-ad5933 | 28 that are allowed to pass through the unknown impedance,
|
| /linux-4.1.27/drivers/power/ |
| D | s3c_adc_battery.c | 128 static int calc_full_volt(int volt_val, int cur_val, int impedance) in calc_full_volt() argument
130 return volt_val + cur_val * impedance / 1000; in calc_full_volt()
|
| /linux-4.1.27/Documentation/devicetree/bindings/mfd/ |
| D | as3722.txt | 67 bias-high-impedance, drive-open-drain.
|
| /linux-4.1.27/Documentation/devicetree/bindings/media/ |
| D | samsung-fimc.txt | 38 ports A and B into high impedance state, especially the CAMCLK clock output
|
| /linux-4.1.27/Documentation/networking/ |
| D | arcnet-hardware.txt | 100 lies in the hybrid chip installed. BUS cards use high impedance output,
101 while STAR use low impedance. Low impedance card (STAR) is electrically
102 equal to a high impedance one with a terminator installed.
158 uses 50 Ohm impedance. You use T connectors to put the computers on a single
|
| /linux-4.1.27/drivers/message/fusion/lsi/ |
| D | mpi_history.txt | 254 * Removed impedance flash from FC Port Page 1.
|
| /linux-4.1.27/Documentation/ |
| D | parport-lowlevel.txt | 1184 Places the data bus in a high impedance state, if port->modes has the
|
| D | pinctrl.txt | 199 may be able to make an output pin high impedance, or "tristate" meaning it is
|
| /linux-4.1.27/Documentation/cgroups/ |
| D | cpusets.txt | 441 There is an impedance mismatch here, between cpusets and sched domains.
|