Home
last modified time | relevance | path

Searched refs:mlx4_err (Results 1 – 19 of 19) sorted by relevance

/linux-4.4.14/drivers/net/ethernet/mellanox/mlx4/
Dreset.c75 mlx4_err(dev, "Couldn't allocate memory to save HCA PCI header, aborting\n"); in mlx4_reset()
87 mlx4_err(dev, "Couldn't save HCA PCI header, aborting\n"); in mlx4_reset()
97 mlx4_err(dev, "Couldn't map HCA reset register, aborting\n"); in mlx4_reset()
112 mlx4_err(dev, "Failed to obtain HW semaphore, aborting\n"); in mlx4_reset()
136 mlx4_err(dev, "PCI device did not come back after reset, aborting\n"); in mlx4_reset()
147 mlx4_err(dev, "Couldn't restore HCA PCI Express Device Control register, aborting\n"); in mlx4_reset()
155 mlx4_err(dev, "Couldn't restore HCA PCI Express Link control register, aborting\n"); in mlx4_reset()
167 mlx4_err(dev, "Couldn't restore HCA reg %x, aborting\n", in mlx4_reset()
176 mlx4_err(dev, "Couldn't restore HCA COMMAND, aborting\n"); in mlx4_reset()
Dcatas.c57 mlx4_err(dev, "Failed to read vendor ID, ret=%d\n", ret); in read_vendor_id()
62 mlx4_err(dev, "PCI can't be accessed to read vendor id\n"); in read_vendor_id()
86 mlx4_err(dev, "Fail to reset HCA\n"); in mlx4_reset_master()
109 mlx4_err(dev, "VF reset is not needed\n"); in mlx4_reset_slave()
114 mlx4_err(dev, "VF reset is not supported\n"); in mlx4_reset_slave()
123 mlx4_err(dev, "Communication channel isn't sync, fail to send reset\n"); in mlx4_reset_slave()
157 mlx4_err(dev, "Fail to send reset over the communication channel\n"); in mlx4_reset_slave()
180 mlx4_err(dev, "device is going to be reset\n"); in mlx4_enter_error_state()
188 mlx4_err(dev, "device was reset successfully\n"); in mlx4_enter_error_state()
221 mlx4_err(dev, "Internal error detected:\n"); in dump_err_buf()
[all …]
Dmain.c179 mlx4_err(dev, "Only same port types supported on this HCA, aborting\n"); in mlx4_check_port_params()
187 mlx4_err(dev, "Requested port type for port %d is not supported on this HCA\n", in mlx4_check_port_params()
215 mlx4_err(dev, "QUERY_DEV_CAP command failed, aborting.\n"); in mlx4_query_func()
295 mlx4_err(dev, "QUERY_PORT command failed.\n"); in mlx4_dev_port()
327 mlx4_err(dev, "QUERY_DEV_CAP command failed, aborting\n"); in mlx4_dev_cap()
333 mlx4_err(dev, "HCA minimum page size of %d bigger than kernel PAGE_SIZE of %ld, aborting\n", in mlx4_dev_cap()
338 mlx4_err(dev, "HCA has %d ports, but we only support %d, aborting\n", in mlx4_dev_cap()
344 …mlx4_err(dev, "HCA reported UAR size of 0x%x bigger than PCI resource 2 size of 0x%llx, aborting\n… in mlx4_dev_cap()
359 mlx4_err(dev, "QUERY_PORT command failed, aborting\n"); in mlx4_dev_cap()
782 mlx4_err(dev, "QUERY_HCA command failed, aborting\n"); in mlx4_slave_cap()
[all …]
Dsense.c51 mlx4_err(dev, "Sense command failed for port: %d\n", port); in mlx4_SENSE_PORT()
56 mlx4_err(dev, "Sense returned illegal value: 0x%llx\n", out_param); in mlx4_SENSE_PORT()
107 mlx4_err(dev, "Failed to change port_types\n"); in mlx4_sense_port()
Den_main.c207 mlx4_err(mdev, "Internal error detected, restarting device\n"); in mlx4_en_event()
262 mlx4_err(mdev, "Failed to create notifier\n"); in mlx4_en_activate()
301 mlx4_err(mdev, "Failed allocating memory region\n"); in mlx4_en_add()
305 mlx4_err(mdev, "Failed enabling memory region\n"); in mlx4_en_add()
311 mlx4_err(mdev, "Bad module parameters, aborting\n"); in mlx4_en_add()
Dmcg.c644 mlx4_err(dev, "QP %06x wasn't found in entry %d\n", in remove_promisc_qp()
733 mlx4_err(dev, "Found zero MGID in AMGM\n"); in find_entry()
763 mlx4_err(dev, "Invalid flow type. type = %d\n", flow_type); in mlx4_map_sw_to_hw_steering_mode()
800 mlx4_err(dev, "Invalid network rule id. id = %d\n", id); in mlx4_map_sw_to_hw_steering_id()
827 mlx4_err(dev, "Invalid network rule id. id = %d\n", id); in mlx4_hw_rule_sz()
907 mlx4_err(dev, "%s", str); in mlx4_err_rule()
970 mlx4_err(dev, "%s", buf); in mlx4_err_rule()
973 mlx4_err(dev, "Network rule error message was truncated, print buffer is too small\n"); in mlx4_err_rule()
1036 mlx4_err(dev, "Fail to detach network rule. registration id = 0x%llx\n", in mlx4_flow_detach()
1133 mlx4_err(dev, "No AMGM entries left\n"); in mlx4_qp_attach_common()
[all …]
Dcmd.c374 mlx4_err(dev, "command 0x%x failed: fw status = 0x%x\n", in mlx4_comm_cmd_wait()
470 mlx4_err(dev, "%s:cmd_pending failed\n", __func__); in mlx4_cmd_post()
543 mlx4_err(dev, "response expected while output mailbox is NULL for command 0x%x\n", in mlx4_slave_cmd()
562 mlx4_err(dev, "response expected while output mailbox is NULL for command 0x%x\n", in mlx4_slave_cmd()
574 mlx4_err(dev, "failed execution of VHCR_POST command opcode 0x%x\n", op); in mlx4_slave_cmd()
604 mlx4_err(dev, "response expected while output mailbox is NULL for command 0x%x\n", in mlx4_cmd_poll()
651 mlx4_err(dev, "command 0x%x failed: fw status = 0x%x\n", in mlx4_cmd_poll()
702 mlx4_err(dev, "response expected while output mailbox is NULL for command 0x%x\n", in mlx4_cmd_wait()
754 mlx4_err(dev, "command 0x%x failed: fw status = 0x%x\n", in mlx4_cmd_wait()
821 …mlx4_err(dev, "Bad access mem params - slave_addr:0x%llx master_addr:0x%llx slave_id:%d size:%d\n", in mlx4_ACCESS_MEM()
[all …]
Dintf.c142 mlx4_err(dev, "Fail to %s rx port check\n", in mlx4_do_bond()
151 mlx4_err(dev, "Fail to reset port map\n"); in mlx4_do_bond()
Dpd.c273 mlx4_err(dev, "Only %d UAR pages (need more than 128)\n", in mlx4_init_uar_table()
275 mlx4_err(dev, "Increase firmware log2_uar_bar_megabytes?\n"); in mlx4_init_uar_table()
Dfw.c475 mlx4_err(dev, "The host supports neither eth nor rdma interfaces\n"); in mlx4_QUERY_FUNC_CAP()
564 mlx4_err(dev, "VLAN is enforced on this port\n"); in mlx4_QUERY_FUNC_CAP()
570 mlx4_err(dev, "Force mac is enabled on this port\n"); in mlx4_QUERY_FUNC_CAP()
577 mlx4_err(dev, "phy_wqe_gid is enforced on this ib port\n"); in mlx4_QUERY_FUNC_CAP()
1522 mlx4_err(dev, "Installed FW has unsupported command interface revision %d\n", in mlx4_QUERY_FW()
1524 mlx4_err(dev, "(Installed FW version is %d.%d.%03d)\n", in mlx4_QUERY_FW()
1528 mlx4_err(dev, "This driver version supports only revisions %d to %d\n", in mlx4_QUERY_FW()
1898 mlx4_err(dev, "INIT_HCA returns %d\n", err); in mlx4_INIT_HCA()
2432 mlx4_err(dev, "Fail to get port %d uplink guid\n", in mlx4_get_phys_port_id()
2497 mlx4_err(dev, "Failed to allocate mailbox for GET_OP_REQ\n"); in mlx4_opreq_action()
[all …]
Den_cq.c121 mlx4_err(mdev, "Failed assigning an EQ to CQ vector %d\n", in mlx4_en_activate_cq()
Den_clock.c300 mlx4_err(mdev, "ptp_clock_register failed\n"); in mlx4_en_init_timestamp()
Dprofile.c162 mlx4_err(dev, "Profile requires 0x%llx bytes; won't fit in 0x%llx bytes of context memory\n", in mlx4_make_profile()
Dqp.c803 mlx4_err(dev, "Number of reserved QPs is higher than number of QPs\n"); in mlx4_init_qp_table()
913 mlx4_err(dev, "Failed to bring QP to state: %d with error: %d\n", in mlx4_qp_to_ready()
Deq.c753 …mlx4_err(dev, "Temperature Threshold was reached! Threshold: %d celsius degrees; Current Temperatu… in mlx4_eq_int()
931 mlx4_err(dev, "Couldn't map EQ doorbell for EQN 0x%06x\n", in mlx4_get_eq_uar()
1130 mlx4_err(dev, "Couldn't map interrupt clear register, aborting\n"); in mlx4_map_clr_int()
Dresource_tracker.c951 mlx4_err(dev, "%s: failed to create new counter for slave %d err %d\n", in handle_unexisting_counter()
3169 …mlx4_err(dev, "%s: unprivileged slave %d attempting to create an MLX proxy special QP on port %d\n… in verify_qp_parameters()
4256 mlx4_err(dev, "Updating qpn 0x%x for slave %d rejected\n", qpn, slave); in mlx4_UPDATE_QP_wrapper()
4268 mlx4_err(dev, "Failed to update qpn 0x%x, MAC is invalid. smac_ix: %d\n", in mlx4_UPDATE_QP_wrapper()
4279 mlx4_err(dev, "Failed to update qpn on qpn 0x%x, command failed\n", qpn); in mlx4_UPDATE_QP_wrapper()
4365 mlx4_err(dev, "Fail to add flow steering resources\n"); in mlx4_QP_FLOW_STEERING_ATTACH_wrapper()
4403 mlx4_err(dev, "Fail to remove flow steering resources\n"); in mlx4_QP_FLOW_STEERING_DETACH_wrapper()
5169 mlx4_err(dev, "%d UPDATE_QP failures for slave %d, port %d\n", in mlx4_vf_immed_vlan_work_handler()
Dmlx4_en.h881 #define mlx4_err(mdev, format, ...) \ macro
Dport.c202 mlx4_err(dev, "Failed adding MAC: 0x%llx\n", in __mlx4_register_mac()
326 mlx4_err(dev, "Failed adding MAC: 0x%llx\n", in __mlx4_replace_mac()
Dmlx4.h224 #define mlx4_err(mdev, format, ...) \ macro