| /linux-4.1.27/Documentation/devicetree/bindings/power/ |
| D | bq2415x.txt | 25 - ti,termination-current: integer, charge will be terminated when current in
43 ti,termination-current = <100>;
|
| /linux-4.1.27/drivers/scsi/ |
| D | advansys.c | 1040 uchar termination; /* 11 0 - automatic */ member
1807 uchar termination; /* Term. Ctrl. bits 6-5 of SCSI_CFG1 register */ member
2497 h->disc_enable, h->termination); in asc_prt_adv_dvc_cfg()
3165 word = ep_3550->termination; in asc_prt_adv_board_eeprom()
3190 ep_3550->termination, termstr, in asc_prt_adv_board_eeprom()
4817 if (asc_dvc->cfg->termination == 0) { in AdvInitAsc3550Driver()
4822 asc_dvc->cfg->termination |= TERM_CTL_SEL; in AdvInitAsc3550Driver()
4832 asc_dvc->cfg->termination |= (TERM_CTL_H | TERM_CTL_L); in AdvInitAsc3550Driver()
4841 asc_dvc->cfg->termination |= TERM_CTL_H; in AdvInitAsc3550Driver()
4862 scsi_cfg1 |= (TERM_CTL_SEL | (~asc_dvc->cfg->termination & TERM_CTL)); in AdvInitAsc3550Driver()
[all …]
|
| D | qla1280.c | 2057 nv->termination.scsi_bus_0_control = 3; in qla1280_set_defaults()
2058 nv->termination.scsi_bus_1_control = 3; in qla1280_set_defaults()
2059 nv->termination.auto_term_support = 1; in qla1280_set_defaults()
2248 term = nv->termination.scsi_bus_1_control; in qla1280_nvram_config()
2249 term |= nv->termination.scsi_bus_0_control << 2; in qla1280_nvram_config()
2250 term |= nv->termination.auto_term_support << 7; in qla1280_nvram_config()
|
| D | qla1280.h | 396 } termination; /* 17 */ member
|
| /linux-4.1.27/Documentation/scsi/ |
| D | qlogicfas.txt | 59 The best way to test if your cables, termination, etc. are good is to
73 termination (the ACK can be reflected), or by noise when the chips
|
| D | in2000.txt | 143 cables or improper termination; 500 ns is a compromise. You can
|
| D | FlashPoint.txt | 125 including smart termination and a flash PROM for easy firmware updates, and
|
| D | BusLogic.txt | 281 are installed in systems with cabling or termination that is not sufficient
347 installed in systems with cabling or termination that is not sufficient for
|
| D | scsi_fc_transport.txt | 464 * fc_vport_terminate - Admin App or LLDD requests termination of a vport
|
| /linux-4.1.27/include/uapi/linux/ |
| D | ixjuser.h | 350 IXJ_CADENCE_TERM termination; member
|
| /linux-4.1.27/Documentation/ABI/testing/ |
| D | sysfs-firmware-dmi | 63 terminated strings, with termination signalled
|
| /linux-4.1.27/arch/arm/boot/dts/ |
| D | vexpress-v2p-ca9.dts | 257 /* DDR2 SDRAM VTT termination voltage */
|
| D | omap3-n900.dts | 618 ti,termination-current = <100>;
|
| /linux-4.1.27/Documentation/locking/ |
| D | locktorture.txt | 67 zero, which disables test termination and system shutdown.
|
| /linux-4.1.27/arch/arm/lib/ |
| D | lib1funcs.S | 98 cmp \dividend, #0 @ Early termination?
|
| /linux-4.1.27/Documentation/power/ |
| D | power_supply_class.txt | 127 CHARGE_TERM_CURRENT - Charge termination current used to detect the end of charge
|
| /linux-4.1.27/Documentation/RCU/ |
| D | torture.txt | 106 zero, which disables test termination and system shutdown.
|
| /linux-4.1.27/drivers/net/can/ |
| D | janz-ican3.c | 1733 static DEVICE_ATTR(termination, S_IWUSR | S_IRUGO, ican3_sysfs_show_term,
|
| /linux-4.1.27/tools/power/cpupower/po/ |
| D | fr.po | 230 msgstr "D�termination du nombre de CPUs (%s : %s) impossible. Assume 1\n"
|
| /linux-4.1.27/drivers/scsi/aic7xxx/ |
| D | aic7xxx.reg | 506 * perform the tasks of accessing a serial eeprom, testing termination
|
| /linux-4.1.27/Documentation/sysctl/ |
| D | kernel.txt | 778 count becomes zero after a detach or a process termination. It will
|
| /linux-4.1.27/scripts/genksyms/ |
| D | parse.tab.c_shipped | 427 /* YYFINAL -- State number of the termination state. */
|
| /linux-4.1.27/scripts/kconfig/ |
| D | zconf.tab.c_shipped | 417 /* YYFINAL -- State number of the termination state. */
|
| /linux-4.1.27/scripts/dtc/ |
| D | dtc-parser.tab.c_shipped | 429 /* YYFINAL -- State number of the termination state. */
|
| /linux-4.1.27/Documentation/networking/ |
| D | arcnet-hardware.txt | 1035 JP0: If closed, internal termination on (default open)
|