| /linux-4.1.27/Documentation/devicetree/bindings/pinctrl/ |
| D | marvell,kirkwood-pinctrl.txt | 27 mpp3 3 gpo, nand(io5), spi(miso)
37 mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
65 mpp3 3 gpo, nand(io5), spi(miso)
75 mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
109 mpp3 3 gpo, nand(io5), spi(miso)
119 mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
140 mpp26 26 gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk)
158 mpp3 3 gpo, nand(io5), spi(miso)
168 mpp11 11 gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
189 mpp26 26 gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk)
[all …]
|
| D | marvell,armada-370-pinctrl.txt | 35 mpp15 15 gpio, ge0(rxctl), pcie(clkreq1), sd0(d3), spi1(miso),
47 mpp26 26 gpio, ge0(crs), ge1(rxd1), spi1(miso)
57 mpp36 36 gpo, dev(a1), spi0(miso)
73 mpp50 50 gpio, dev(ad11), uart0(cts), sd0(d1), spi1(miso),
95 mpp64 64 gpio, spi0(miso), spi0(cs1)
|
| D | marvell,armada-375-pinctrl.txt | 20 mpp4 4 gpio, dev(ad6), spi0(miso), spi1(miso)
49 mpp33 33 gpio, ge1(txd3), spi1(miso)
|
| D | marvell,armada-39x-pinctrl.txt | 33 mpp16 16 gpio, m(decc), spi0(miso), i2c1(sda)
41 mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
75 mpp58 58 gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
|
| D | marvell,dove-pinctrl.txt | 24 mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso), pmu*
44 mpp20 20 gpio, sdio0(cd), sdio1(cd), spi1(miso), lcd-spi(miso),
|
| D | marvell,armada-38x-pinctrl.txt | 34 mpp16 16 gpio, ge0(rxctl), ge(mdio slave), m(decc_err), spi0(miso), pcie0(clkreq), pc…
42 mpp24 24 gpio, spi0(miso), ua0(cts), ua1(rxd), sd0(d4), dev(ready)
76 mpp58 58 gpio, pcie1(clkreq) [1], i2c1(sck), pcie2(clkreq), spi1(miso), sd0(d1)
|
| D | marvell,armada-xp-pinctrl.txt | 58 mpp37 37 gpio, spi(miso)
|
| /linux-4.1.27/Documentation/devicetree/bindings/spi/ |
| D | spi-gpio.txt | 9 - gpio-miso: GPIO spec for the MISO line to use
24 gpio-miso = <&gpio 98 0>;
|
| D | spi-samsung.txt | 49 miso line (to account for any lag in the miso line). The following are the
|
| /linux-4.1.27/include/linux/spi/ |
| D | spi_gpio.h | 66 unsigned long miso; member
|
| /linux-4.1.27/drivers/misc/eeprom/ |
| D | digsy_mtc_eeprom.c | 47 .miso = GPIO_EEPROM_DO,
|
| /linux-4.1.27/drivers/spi/ |
| D | spi-gpio.c | 81 #define SPI_MISO_GPIO ((pdata)->miso)
371 pdata->miso = SPI_GPIO_NO_MISO; in spi_gpio_probe_dt()
373 pdata->miso = ret; in spi_gpio_probe_dt()
|
| /linux-4.1.27/arch/arm/boot/dts/ |
| D | qcom-apq8074-dragonboard.dts | 39 miso {
|
| D | imx28-cfa10056.dts | 104 gpio-miso = <&gpio2 18 0>;
|
| D | imx28-cfa10055.dts | 145 gpio-miso = <&gpio2 18 0>;
|
| D | imx28-cfa10049.dts | 343 gpio-miso = <&gpio2 18 0>;
|
| D | omap3-gta04.dtsi | 59 gpio-miso = <&gpio1 18 0>;
|
| D | imx28-tx28.dts | 219 gpio-miso = <&gpio2 26 GPIO_ACTIVE_HIGH>;
|
| D | stih416-pinctrl.dtsi | 355 spi-fsm-miso = <&pio12 5 ALT1 IN>;
|
| /linux-4.1.27/arch/arm/mach-s3c24xx/ |
| D | mach-jive.c | 397 .miso = SPI_GPIO_NO_MISO,
412 .miso = SPI_GPIO_NO_MISO,
|
| D | mach-qt2410.c | 216 .miso = S3C2410_GPG(5),
|
| /linux-4.1.27/arch/arm/mach-s3c64xx/ |
| D | mach-smartq.c | 212 .miso = S3C64XX_GPM(2),
|
| /linux-4.1.27/arch/mips/jz4740/ |
| D | board-qi_lb60.c | 304 .miso = -1,
|
| /linux-4.1.27/arch/mips/alchemy/devboards/ |
| D | db1000.c | 451 .miso = 207,
|
| /linux-4.1.27/arch/arm/mach-pxa/ |
| D | cm-x300.c | 343 .miso = GPIO_LCD_DOUT,
|
| D | raumfeld.c | 636 .miso = GPIO_SPI_MISO,
|