| /linux-4.1.27/arch/mips/oprofile/ |
| H A D | op_model_loongson3.c | 46 unsigned int control1; member in struct:loongson3_register_config
64 unsigned int control1 = 0; loongson3_reg_setup() local
72 control1 |= LOONGSON3_PERFCTRL_EVENT(0, ctr[0].event) | loongson3_reg_setup()
75 control1 |= LOONGSON3_PERFCTRL_KERNEL; loongson3_reg_setup()
77 control1 |= LOONGSON3_PERFCTRL_USER; loongson3_reg_setup()
92 control1 |= LOONGSON3_PERFCTRL_EXL; loongson3_reg_setup()
96 reg.control1 = control1; loongson3_reg_setup()
116 reg.control1 |= (LOONGSON3_PERFCTRL_W|LOONGSON3_PERFCTRL_M); loongson3_cpu_start()
120 write_c0_perflo1(reg.control1); loongson3_cpu_start()
177 write_c0_perflo1(reg.control1); loongson3_cpu_callback()
|
| /linux-4.1.27/drivers/regulator/ |
| H A D | max8973-regulator.c | 257 uint8_t control1 = 0; max8973_init_dcdc() local
261 control1 |= MAX8973_SNS_ENABLE; max8973_init_dcdc()
264 control1 |= MAX8973_NFSR_ENABLE; max8973_init_dcdc()
267 control1 |= MAX8973_AD_ENABLE; max8973_init_dcdc()
270 control1 |= MAX8973_BIAS_ENABLE; max8973_init_dcdc()
273 control1 |= MAX8973_FREQSHIFT_9PER; max8973_init_dcdc()
279 control1 |= MAX8973_RAMP_12mV_PER_US; max8973_init_dcdc()
281 control1 |= MAX8973_RAMP_25mV_PER_US; max8973_init_dcdc()
283 control1 |= MAX8973_RAMP_50mV_PER_US; max8973_init_dcdc()
285 control1 |= MAX8973_RAMP_200mV_PER_US; max8973_init_dcdc()
287 control1 |= MAX8973_RAMP_12mV_PER_US; max8973_init_dcdc()
332 ret = regmap_write(max->regmap, MAX8973_CONTROL1, control1); max8973_init_dcdc()
|
| /linux-4.1.27/drivers/staging/rtl8723au/include/ |
| H A D | Hal8723APhyCfg.h | 54 u32 rfHSSIPara1; /* wire parameter control1 : */
60 u32 rfAGCControl1; /* AGC parameter control1 : */
|
| /linux-4.1.27/drivers/staging/rtl8188eu/include/ |
| H A D | Hal8188EPhyCfg.h | 135 u32 rfHSSIPara1; /* wire parameter control1 : */
143 u32 rfAGCControl1; /* AGC parameter control1 : */
|
| /linux-4.1.27/include/linux/amba/ |
| H A D | pl080.h | 144 u32 control1; member in struct:pl080s_lli
|
| /linux-4.1.27/drivers/crypto/ |
| H A D | mxs-dcp.c | 38 uint32_t control1; member in struct:dcp_dma_desc
225 desc->control1 = MXS_DCP_CONTROL1_CIPHER_SELECT_AES128; mxs_dcp_run_aes()
228 desc->control1 |= MXS_DCP_CONTROL1_CIPHER_MODE_ECB; mxs_dcp_run_aes()
230 desc->control1 |= MXS_DCP_CONTROL1_CIPHER_MODE_CBC; mxs_dcp_run_aes()
532 desc->control1 = actx->alg; mxs_dcp_run_sha()
|
| /linux-4.1.27/drivers/net/wireless/b43/ |
| H A D | dma.h | 144 __le32 control1; member in struct:b43_dmadesc64
|
| H A D | dma.c | 221 desc->dma64.control1 = cpu_to_le32(ctl1); op64_fill_descriptor()
|
| /linux-4.1.27/drivers/staging/rtl8192u/ |
| H A D | r8192U.h | 707 /* wire parameter control1: 0x820~0x823, 0x828~0x82b,
715 /* AGC parameter control1: 0xc50~0xc53, 0xc58~0xc5b,
|
| /linux-4.1.27/drivers/scsi/ |
| H A D | gdth.h | 783 u8 control1; /* board interrupts enable */ member in struct:__anon8894
|
| H A D | gdth.c | 1041 outb(0x00,PTR2USHORT(&ha->plx->control1)); gdth_init_pci()
1260 outb(0x03, PTR2USHORT(&ha->plx->control1)); gdth_enable_int()
|
| /linux-4.1.27/drivers/net/ethernet/broadcom/bnx2x/ |
| H A D | bnx2x_link.c | 5255 u16 control1; bnx2x_initialize_sgmii_process() local
5262 &control1); bnx2x_initialize_sgmii_process()
5263 control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT; bnx2x_initialize_sgmii_process()
5265 control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE | bnx2x_initialize_sgmii_process()
5271 control1); bnx2x_initialize_sgmii_process()
|
| /linux-4.1.27/drivers/media/usb/gspca/ |
| H A D | sonixj.c | 945 {0xa1, 0x6e, 0x1d, 0x08, 0x00, 0x00, 0x00, 0x10}, /* control1 */
|
| /linux-4.1.27/drivers/net/wireless/ |
| H A D | mwl8k.c | 4452 __le16 control1; member in struct:ewc_ht_info
|
| /linux-4.1.27/drivers/gpu/drm/i915/ |
| H A D | i915_reg.h | 6731 /* DPLL control1 */
|