| /linux-4.1.27/arch/sh/kernel/cpu/sh4/ |
| D | setup-sh7760.c | 26 SSI0, SSI1, enumerator
55 INTC_VECT(SSI0, 0x940), INTC_VECT(SSI1, 0x960),
92 SSI0, SSI1, HAC0, HAC1, I2C0, I2C1, USB, LCDC,
111 { 0xfe080004, 0, 32, 4, /* INTPRI04 */ { HCAN20, HCAN21, SSI0, SSI1,
|
| /linux-4.1.27/arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7763.c | 250 TMU3, TMU4, TMU5, ADC, SSI0, SSI1, SSI2, SSI3, enumerator
293 INTC_VECT(SSI0, 0xe80), INTC_VECT(SSI1, 0xea0),
316 LCDC, 0, IIC1, IIC0, SSI3, SSI2, SSI1, 0 } },
331 { 0xffd400a0, 0, 32, 8, /* INT2PRI8 */ { SSI3, SSI2, SSI1, 0 } },
|
| D | setup-sh7785.c | 391 SSI0, SSI1, enumerator
433 INTC_VECT(SSI0, 0xe80), INTC_VECT(SSI1, 0xea0),
461 { 0, 0, 0, GDTA, DU, SSI0, SSI1, GPIO,
482 { 0xffd40020, 0, 32, 8, /* INT2PRI8 */ { FLCTL, GPIO, SSI0, SSI1, } },
|
| D | setup-sh7786.c | 498 SSI0, SSI1, SSI2, SSI3, enumerator
541 INTC_VECT(SSI0, 0xd20), INTC_VECT(SSI1, 0xd40),
614 DU, SSI0, SSI1, SSI2, SSI3,
653 { 0xfe41084c, 0, 32, 8, /* INT2PRI19 */ { DU, SSI0, SSI1, SSI2 } },
|
| D | setup-sh7734.c | 316 SSI0, SSI1, SSI2, SSI3, enumerator
392 INTC_VECT(SSI1, 0x6E0),
447 INTC_GROUP(SSI, SSI0, SSI1, SSI2, SSI3),
|
| /linux-4.1.27/Documentation/devicetree/bindings/interrupt-controller/ |
| D | cirrus,clps711x-intc.txt | 27 15: SSEOTI SSI1 end of transfer
|
| /linux-4.1.27/Documentation/devicetree/bindings/sound/ |
| D | fsl,ssi.txt | 13 - cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
75 and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
|
| /linux-4.1.27/arch/arm/boot/dts/ |
| D | imx53-voipac-bsb.dts | 115 pinctrl-0 = <&pinctrl_audmux>; /* SSI1 */
|
| /linux-4.1.27/drivers/spi/ |
| D | Kconfig | 172 master mode interface (SSI1) for CLPS711X-based CPUs.
|