For historical reasons, frontend types are named by the type of modulation used in transmission. The fontend types are given by fe_type_t type, defined as:

Newer formats like DVB-S2, ISDB-T, ISDB-S and DVB-T2 are not described at the above, as they're supported via the new FE_GET_PROPERTY/FE_GET_SET_PROPERTY ioctl's, using the DTV_DELIVERY_SYSTEM parameter.

The usage of this field is deprecated, as it doesn't report all supported standards, and will provide an incomplete information for frontends that support multiple delivery systems. Please use DTV_ENUM_DELSYS instead.

Capabilities describe what a frontend can do. Some capabilities can only be supported for a specific frontend type.

	typedef enum fe_caps {
	FE_IS_STUPID                  = 0,
	FE_CAN_INVERSION_AUTO         = 0x1,
	FE_CAN_FEC_1_2                = 0x2,
	FE_CAN_FEC_2_3                = 0x4,
	FE_CAN_FEC_3_4                = 0x8,
	FE_CAN_FEC_4_5                = 0x10,
	FE_CAN_FEC_5_6                = 0x20,
	FE_CAN_FEC_6_7                = 0x40,
	FE_CAN_FEC_7_8                = 0x80,
	FE_CAN_FEC_8_9                = 0x100,
	FE_CAN_FEC_AUTO               = 0x200,
	FE_CAN_QPSK                   = 0x400,
	FE_CAN_QAM_16                 = 0x800,
	FE_CAN_QAM_32                 = 0x1000,
	FE_CAN_QAM_64                 = 0x2000,
	FE_CAN_QAM_128                = 0x4000,
	FE_CAN_QAM_256                = 0x8000,
	FE_CAN_QAM_AUTO               = 0x10000,
	FE_CAN_TRANSMISSION_MODE_AUTO = 0x20000,
	FE_CAN_BANDWIDTH_AUTO         = 0x40000,
	FE_CAN_GUARD_INTERVAL_AUTO    = 0x80000,
	FE_CAN_HIERARCHY_AUTO         = 0x100000,
	FE_CAN_8VSB                   = 0x200000,
	FE_CAN_16VSB                  = 0x400000,
	FE_HAS_EXTENDED_CAPS          = 0x800000,
	FE_CAN_MULTISTREAM            = 0x4000000,
	FE_CAN_TURBO_FEC              = 0x8000000,
	FE_CAN_2G_MODULATION          = 0x10000000,
	FE_NEEDS_BENDING              = 0x20000000,
	FE_CAN_RECOVER                = 0x40000000,
	FE_CAN_MUTE_TS                = 0x80000000
	} fe_caps_t;

Information about the frontend ca be queried with FE_GET_INFO.

	struct dvb_frontend_info {
	char       name[128];
	fe_type_t  type;
	uint32_t   frequency_min;
	uint32_t   frequency_max;
	uint32_t   frequency_stepsize;
	uint32_t   frequency_tolerance;
	uint32_t   symbol_rate_min;
	uint32_t   symbol_rate_max;
	uint32_t   symbol_rate_tolerance;     /⋆ ppm ⋆/
	uint32_t   notifier_delay;            /⋆ ms ⋆/
	fe_caps_t  caps;
	};

A message sent from the frontend to DiSEqC capable equipment.

	struct dvb_diseqc_master_cmd {
	uint8_t msg [6]; /⋆  { framing, address, command, data[3] } ⋆/
	uint8_t msg_len; /⋆  valid values are 3...6  ⋆/
	};

A reply to the frontend from DiSEqC 2.0 capable equipment.

	struct dvb_diseqc_slave_reply {
	uint8_t msg [4]; /⋆  { framing, data [3] } ⋆/
	uint8_t msg_len; /⋆  valid values are 0...4, 0 means no msg  ⋆/
	int     timeout; /⋆  return from ioctl after timeout ms with ⋆/
	};                       /⋆  errorcode when no message was received  ⋆/

The voltage is usually used with non-DiSEqC capable LNBs to switch the polarzation (horizontal/vertical). When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.

	typedef enum fe_sec_voltage {
	SEC_VOLTAGE_13,
	SEC_VOLTAGE_18
	} fe_sec_voltage_t;

The continuous 22KHz tone is usually used with non-DiSEqC capable LNBs to switch the high/low band of a dual-band LNB. When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.

	typedef enum fe_sec_tone_mode {
	SEC_TONE_ON,
	SEC_TONE_OFF
	} fe_sec_tone_mode_t;

The 22KHz tone burst is usually used with non-DiSEqC capable switches to select between two connected LNBs/satellites. When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.

	typedef enum fe_sec_mini_cmd {
	SEC_MINI_A,
	SEC_MINI_B
	} fe_sec_mini_cmd_t;

Several functions of the frontend device use the fe_status data type defined by

typedef enum fe_status {
	FE_HAS_SIGNAL		= 0x01,
	FE_HAS_CARRIER		= 0x02,
	FE_HAS_VITERBI		= 0x04,
	FE_HAS_SYNC		= 0x08,
	FE_HAS_LOCK		= 0x10,
	FE_TIMEDOUT		= 0x20,
	FE_REINIT		= 0x40,
} fe_status_t;

to indicate the current state and/or state changes of the frontend hardware:

The kind of parameters passed to the frontend device for tuning depend on the kind of hardware you are using.

The struct dvb_frontend_parameters uses an union with specific per-system parameters. However, as newer delivery systems required more data, the structure size weren't enough to fit, and just extending its size would break the existing applications. So, those parameters were replaced by the usage of FE_GET_PROPERTY/FE_SET_PROPERTY ioctl's. The new API is flexible enough to add new parameters to existing delivery systems, and to add newer delivery systems.

So, newer applications should use FE_GET_PROPERTY/FE_SET_PROPERTY instead, in order to be able to support the newer System Delivery like DVB-S2, DVB-T2, DVB-C2, ISDB, etc.

All kinds of parameters are combined as an union in the FrontendParameters structure:

struct dvb_frontend_parameters {
	uint32_t frequency;     /⋆ (absolute) frequency in Hz for QAM/OFDM ⋆/
				/⋆ intermediate frequency in kHz for QPSK ⋆/
	fe_spectral_inversion_t inversion;
	union {
		struct dvb_qpsk_parameters qpsk;
		struct dvb_qam_parameters  qam;
		struct dvb_ofdm_parameters ofdm;
		struct dvb_vsb_parameters  vsb;
	} u;
};

In the case of QPSK frontends the frequency field specifies the intermediate frequency, i.e. the offset which is effectively added to the local oscillator frequency (LOF) of the LNB. The intermediate frequency has to be specified in units of kHz. For QAM and OFDM frontends the frequency specifies the absolute frequency and is given in Hz.

 struct dvb_qpsk_parameters {
	 uint32_t        symbol_rate;  /⋆ symbol rate in Symbols per second ⋆/
	 fe_code_rate_t  fec_inner;    /⋆ forward error correction (see above) ⋆/
 };

 struct dvb_qam_parameters {
	 uint32_t         symbol_rate; /⋆ symbol rate in Symbols per second ⋆/
	 fe_code_rate_t   fec_inner;   /⋆ forward error correction (see above) ⋆/
	 fe_modulation_t  modulation;  /⋆ modulation type (see above) ⋆/
 };

struct dvb_vsb_parameters {
	fe_modulation_t modulation;	/⋆ modulation type (see above) ⋆/
};

 struct dvb_ofdm_parameters {
	 fe_bandwidth_t      bandwidth;
	 fe_code_rate_t      code_rate_HP;  /⋆ high priority stream code rate ⋆/
	 fe_code_rate_t      code_rate_LP;  /⋆ low priority stream code rate ⋆/
	 fe_modulation_t     constellation; /⋆ modulation type (see above) ⋆/
	 fe_transmit_mode_t  transmission_mode;
	 fe_guard_interval_t guard_interval;
	 fe_hierarchy_t      hierarchy_information;
 };

typedef enum fe_spectral_inversion {
	INVERSION_OFF,
	INVERSION_ON,
	INVERSION_AUTO
} fe_spectral_inversion_t;

typedef enum fe_code_rate {
	FEC_NONE = 0,
	FEC_1_2,
	FEC_2_3,
	FEC_3_4,
	FEC_4_5,
	FEC_5_6,
	FEC_6_7,
	FEC_7_8,
	FEC_8_9,
	FEC_AUTO,
	FEC_3_5,
	FEC_9_10,
} fe_code_rate_t;

 typedef enum fe_modulation {
	QPSK,
	QAM_16,
	QAM_32,
	QAM_64,
	QAM_128,
	QAM_256,
	QAM_AUTO,
	VSB_8,
	VSB_16,
	PSK_8,
	APSK_16,
	APSK_32,
	DQPSK,
 } fe_modulation_t;

typedef enum fe_transmit_mode {
	TRANSMISSION_MODE_2K,
	TRANSMISSION_MODE_8K,
	TRANSMISSION_MODE_AUTO,
	TRANSMISSION_MODE_4K,
	TRANSMISSION_MODE_1K,
	TRANSMISSION_MODE_16K,
	TRANSMISSION_MODE_32K,
 } fe_transmit_mode_t;

typedef enum fe_bandwidth {
	BANDWIDTH_8_MHZ,
	BANDWIDTH_7_MHZ,
	BANDWIDTH_6_MHZ,
	BANDWIDTH_AUTO,
	BANDWIDTH_5_MHZ,
	BANDWIDTH_10_MHZ,
	BANDWIDTH_1_712_MHZ,
} fe_bandwidth_t;

typedef enum fe_guard_interval {
	GUARD_INTERVAL_1_32,
	GUARD_INTERVAL_1_16,
	GUARD_INTERVAL_1_8,
	GUARD_INTERVAL_1_4,
	GUARD_INTERVAL_AUTO,
	GUARD_INTERVAL_1_128,
	GUARD_INTERVAL_19_128,
	GUARD_INTERVAL_19_256,
} fe_guard_interval_t;

typedef enum fe_hierarchy {
	 HIERARCHY_NONE,
	 HIERARCHY_1,
	 HIERARCHY_2,
	 HIERARCHY_4,
	 HIERARCHY_AUTO
 } fe_hierarchy_t;

 struct dvb_frontend_event {
	 fe_status_t status;
	 struct dvb_frontend_parameters parameters;
 };