44 #define rdev_err(rdev, fmt, ...)					\  macro
219 		rdev_err(rdev, "no constraints\n");  in regulator_check_voltage()
223 		rdev_err(rdev, "voltage operation not allowed\n");  in regulator_check_voltage()
233 		rdev_err(rdev, "unsupportable voltage range: %d-%duV\n",  in regulator_check_voltage()
264 		rdev_err(rdev, "Restricting voltage, %u-%uuV\n",  in regulator_check_consumers()
279 		rdev_err(rdev, "no constraints\n");  in regulator_check_current_limit()
283 		rdev_err(rdev, "current operation not allowed\n");  in regulator_check_current_limit()
293 		rdev_err(rdev, "unsupportable current range: %d-%duA\n",  in regulator_check_current_limit()
311 		rdev_err(rdev, "invalid mode %x specified\n", *mode);  in regulator_mode_constrain()
316 		rdev_err(rdev, "no constraints\n");  in regulator_mode_constrain()
320 		rdev_err(rdev, "mode operation not allowed\n");  in regulator_mode_constrain()
340 		rdev_err(rdev, "no constraints\n");  in regulator_check_drms()
710 		rdev_err(rdev, "invalid output voltage found\n");  in drms_uA_update()
721 		rdev_err(rdev, "invalid input voltage found\n");  in drms_uA_update()
735 			rdev_err(rdev, "failed to set load %d\n", current_uA);  in drms_uA_update()
744 			rdev_err(rdev, "failed to get optimum mode @ %d uA %d -> %d uV\n",  in drms_uA_update()
751 			rdev_err(rdev, "failed to set optimum mode %x\n", mode);  in drms_uA_update()
774 		rdev_err(rdev, "invalid configuration\n");  in suspend_set_state()
786 		rdev_err(rdev, "failed to enabled/disable\n");  in suspend_set_state()
793 			rdev_err(rdev, "failed to set voltage\n");  in suspend_set_state()
801 			rdev_err(rdev, "failed to set mode\n");  in suspend_set_state()
912 			rdev_err(rdev,  in machine_constraints_voltage()
923 				rdev_err(rdev,  in machine_constraints_voltage()
957 			rdev_err(rdev, "invalid voltage constraints\n");  in machine_constraints_voltage()
978 			rdev_err(rdev,  in machine_constraints_voltage()
1010 		rdev_err(rdev, "Invalid current constraints\n");  in machine_constraints_current()
1023 		rdev_err(rdev, "Failed to set current constraint, %d\n", ret);  in machine_constraints_current()
1070 			rdev_err(rdev, "failed to set input limit\n");  in set_machine_constraints()
1079 			rdev_err(rdev, "failed to set suspend state\n");  in set_machine_constraints()
1086 			rdev_err(rdev, "no set_mode operation\n");  in set_machine_constraints()
1093 			rdev_err(rdev, "failed to set initial mode: %d\n", ret);  in set_machine_constraints()
1104 			rdev_err(rdev, "failed to enable\n");  in set_machine_constraints()
1113 			rdev_err(rdev, "failed to set ramp_delay\n");  in set_machine_constraints()
1121 			rdev_err(rdev, "failed to set pull down\n");  in set_machine_constraints()
1129 			rdev_err(rdev, "failed to set soft start\n");  in set_machine_constraints()
1138 			rdev_err(rdev, "failed to set over current protection\n");  in set_machine_constraints()
2113 			rdev_err(rdev, "is_enabled() failed: %d\n", ret);  in _regulator_enable()
2216 				rdev_err(rdev, "failed to disable\n");  in _regulator_disable()
2285 		rdev_err(rdev, "failed to force disable\n");  in _regulator_force_disable()
2340 			rdev_err(rdev, "Deferred disable failed: %d\n", ret);  in regulator_disable_work()
2349 				rdev_err(rdev,  in regulator_disable_work()
3941 			rdev_err(rdev, "Failed to request enable GPIO%d: %d\n",  in regulator_register()
4398 			rdev_err(rdev, "couldn't disable: %d\n", ret);  in regulator_late_cleanup()