arch/powerpc/include/asm/cpm.h

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
cpm_command
   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 #ifndef __CPM_H
   3 #define __CPM_H
   4 
   5 #include <linux/compiler.h>
   6 #include <linux/types.h>
   7 #include <linux/errno.h>
   8 #include <linux/of.h>
   9 #include <soc/fsl/qe/qe.h>
  10 
  11 /*
  12  * SPI Parameter RAM common to QE and CPM.
  13  */
  14 struct spi_pram {
  15         __be16  rbase;  /* Rx Buffer descriptor base address */
  16         __be16  tbase;  /* Tx Buffer descriptor base address */
  17         u8      rfcr;   /* Rx function code */
  18         u8      tfcr;   /* Tx function code */
  19         __be16  mrblr;  /* Max receive buffer length */
  20         __be32  rstate; /* Internal */
  21         __be32  rdp;    /* Internal */
  22         __be16  rbptr;  /* Internal */
  23         __be16  rbc;    /* Internal */
  24         __be32  rxtmp;  /* Internal */
  25         __be32  tstate; /* Internal */
  26         __be32  tdp;    /* Internal */
  27         __be16  tbptr;  /* Internal */
  28         __be16  tbc;    /* Internal */
  29         __be32  txtmp;  /* Internal */
  30         __be32  res;    /* Tx temp. */
  31         __be16  rpbase; /* Relocation pointer (CPM1 only) */
  32         __be16  res1;   /* Reserved */
  33 };
  34 
  35 /*
  36  * USB Controller pram common to QE and CPM.
  37  */
  38 struct usb_ctlr {
  39         u8      usb_usmod;
  40         u8      usb_usadr;
  41         u8      usb_uscom;
  42         u8      res1[1];
  43         __be16  usb_usep[4];
  44         u8      res2[4];
  45         __be16  usb_usber;
  46         u8      res3[2];
  47         __be16  usb_usbmr;
  48         u8      res4[1];
  49         u8      usb_usbs;
  50         /* Fields down below are QE-only */
  51         __be16  usb_ussft;
  52         u8      res5[2];
  53         __be16  usb_usfrn;
  54         u8      res6[0x22];
  55 } __attribute__ ((packed));
  56 
  57 /*
  58  * Function code bits, usually generic to devices.
  59  */
  60 #ifdef CONFIG_CPM1
  61 #define CPMFCR_GBL      ((u_char)0x00)  /* Flag doesn't exist in CPM1 */
  62 #define CPMFCR_TC2      ((u_char)0x00)  /* Flag doesn't exist in CPM1 */
  63 #define CPMFCR_DTB      ((u_char)0x00)  /* Flag doesn't exist in CPM1 */
  64 #define CPMFCR_BDB      ((u_char)0x00)  /* Flag doesn't exist in CPM1 */
  65 #else
  66 #define CPMFCR_GBL      ((u_char)0x20)  /* Set memory snooping */
  67 #define CPMFCR_TC2      ((u_char)0x04)  /* Transfer code 2 value */
  68 #define CPMFCR_DTB      ((u_char)0x02)  /* Use local bus for data when set */
  69 #define CPMFCR_BDB      ((u_char)0x01)  /* Use local bus for BD when set */
  70 #endif
  71 #define CPMFCR_EB       ((u_char)0x10)  /* Set big endian byte order */
  72 
  73 /* Opcodes common to CPM1 and CPM2
  74 */
  75 #define CPM_CR_INIT_TRX         ((ushort)0x0000)
  76 #define CPM_CR_INIT_RX          ((ushort)0x0001)
  77 #define CPM_CR_INIT_TX          ((ushort)0x0002)
  78 #define CPM_CR_HUNT_MODE        ((ushort)0x0003)
  79 #define CPM_CR_STOP_TX          ((ushort)0x0004)
  80 #define CPM_CR_GRA_STOP_TX      ((ushort)0x0005)
  81 #define CPM_CR_RESTART_TX       ((ushort)0x0006)
  82 #define CPM_CR_CLOSE_RX_BD      ((ushort)0x0007)
  83 #define CPM_CR_SET_GADDR        ((ushort)0x0008)
  84 #define CPM_CR_SET_TIMER        ((ushort)0x0008)
  85 #define CPM_CR_STOP_IDMA        ((ushort)0x000b)
  86 
  87 /* Buffer descriptors used by many of the CPM protocols. */
  88 typedef struct cpm_buf_desc {
  89         ushort  cbd_sc;         /* Status and Control */
  90         ushort  cbd_datlen;     /* Data length in buffer */
  91         uint    cbd_bufaddr;    /* Buffer address in host memory */
  92 } cbd_t;
  93 
  94 /* Buffer descriptor control/status used by serial
  95  */
  96 
  97 #define BD_SC_EMPTY     (0x8000)        /* Receive is empty */
  98 #define BD_SC_READY     (0x8000)        /* Transmit is ready */
  99 #define BD_SC_WRAP      (0x2000)        /* Last buffer descriptor */
 100 #define BD_SC_INTRPT    (0x1000)        /* Interrupt on change */
 101 #define BD_SC_LAST      (0x0800)        /* Last buffer in frame */
 102 #define BD_SC_TC        (0x0400)        /* Transmit CRC */
 103 #define BD_SC_CM        (0x0200)        /* Continuous mode */
 104 #define BD_SC_ID        (0x0100)        /* Rec'd too many idles */
 105 #define BD_SC_P         (0x0100)        /* xmt preamble */
 106 #define BD_SC_BR        (0x0020)        /* Break received */
 107 #define BD_SC_FR        (0x0010)        /* Framing error */
 108 #define BD_SC_PR        (0x0008)        /* Parity error */
 109 #define BD_SC_NAK       (0x0004)        /* NAK - did not respond */
 110 #define BD_SC_OV        (0x0002)        /* Overrun */
 111 #define BD_SC_UN        (0x0002)        /* Underrun */
 112 #define BD_SC_CD        (0x0001)        /* */
 113 #define BD_SC_CL        (0x0001)        /* Collision */
 114 
 115 /* Buffer descriptor control/status used by Ethernet receive.
 116  * Common to SCC and FCC.
 117  */
 118 #define BD_ENET_RX_EMPTY        (0x8000)
 119 #define BD_ENET_RX_WRAP         (0x2000)
 120 #define BD_ENET_RX_INTR         (0x1000)
 121 #define BD_ENET_RX_LAST         (0x0800)
 122 #define BD_ENET_RX_FIRST        (0x0400)
 123 #define BD_ENET_RX_MISS         (0x0100)
 124 #define BD_ENET_RX_BC           (0x0080)        /* FCC Only */
 125 #define BD_ENET_RX_MC           (0x0040)        /* FCC Only */
 126 #define BD_ENET_RX_LG           (0x0020)
 127 #define BD_ENET_RX_NO           (0x0010)
 128 #define BD_ENET_RX_SH           (0x0008)
 129 #define BD_ENET_RX_CR           (0x0004)
 130 #define BD_ENET_RX_OV           (0x0002)
 131 #define BD_ENET_RX_CL           (0x0001)
 132 #define BD_ENET_RX_STATS        (0x01ff)        /* All status bits */
 133 
 134 /* Buffer descriptor control/status used by Ethernet transmit.
 135  * Common to SCC and FCC.
 136  */
 137 #define BD_ENET_TX_READY        (0x8000)
 138 #define BD_ENET_TX_PAD          (0x4000)
 139 #define BD_ENET_TX_WRAP         (0x2000)
 140 #define BD_ENET_TX_INTR         (0x1000)
 141 #define BD_ENET_TX_LAST         (0x0800)
 142 #define BD_ENET_TX_TC           (0x0400)
 143 #define BD_ENET_TX_DEF          (0x0200)
 144 #define BD_ENET_TX_HB           (0x0100)
 145 #define BD_ENET_TX_LC           (0x0080)
 146 #define BD_ENET_TX_RL           (0x0040)
 147 #define BD_ENET_TX_RCMASK       (0x003c)
 148 #define BD_ENET_TX_UN           (0x0002)
 149 #define BD_ENET_TX_CSL          (0x0001)
 150 #define BD_ENET_TX_STATS        (0x03ff)        /* All status bits */
 151 
 152 /* Buffer descriptor control/status used by Transparent mode SCC.
 153  */
 154 #define BD_SCC_TX_LAST          (0x0800)
 155 
 156 /* Buffer descriptor control/status used by I2C.
 157  */
 158 #define BD_I2C_START            (0x0400)
 159 
 160 #ifdef CONFIG_CPM
 161 int cpm_command(u32 command, u8 opcode);
 162 #else
 163 static inline int cpm_command(u32 command, u8 opcode)
 164 {
 165         return -ENOSYS;
 166 }
 167 #endif /* CONFIG_CPM */
 168 
 169 int cpm2_gpiochip_add32(struct device *dev);
 170 
 171 #endif
/* [<][>][^][v][top][bottom][index][help] */
root/arch/powerpc/include/asm/cpm.h

INCLUDED FROM

DEFINITIONS
