1 /* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ 2 /* 3 * usr/include/linux/lp.h c.1991-1992 James Wiegand 4 * many modifications copyright (C) 1992 Michael K. Johnson 5 * Interrupt support added 1993 Nigel Gamble 6 * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti 7 */ 8 #ifndef _UAPI_LINUX_LP_H 9 #define _UAPI_LINUX_LP_H 10 11 #include <linux/types.h> 12 #include <linux/ioctl.h> 13 14 /* 15 * Per POSIX guidelines, this module reserves the LP and lp prefixes 16 * These are the lp_table[minor].flags flags... 17 */ 18 #define LP_EXIST 0x0001 19 #define LP_SELEC 0x0002 20 #define LP_BUSY 0x0004 21 #define LP_BUSY_BIT_POS 2 22 #define LP_OFFL 0x0008 23 #define LP_NOPA 0x0010 24 #define LP_ERR 0x0020 25 #define LP_ABORT 0x0040 26 #define LP_CAREFUL 0x0080 /* obsoleted -arca */ 27 #define LP_ABORTOPEN 0x0100 28 29 #define LP_TRUST_IRQ_ 0x0200 /* obsolete */ 30 #define LP_NO_REVERSE 0x0400 /* No reverse mode available. */ 31 #define LP_DATA_AVAIL 0x0800 /* Data is available. */ 32 33 /* 34 * bit defines for 8255 status port 35 * base + 1 36 * accessed with LP_S(minor), which gets the byte... 37 */ 38 #define LP_PBUSY 0x80 /* inverted input, active high */ 39 #define LP_PACK 0x40 /* unchanged input, active low */ 40 #define LP_POUTPA 0x20 /* unchanged input, active high */ 41 #define LP_PSELECD 0x10 /* unchanged input, active high */ 42 #define LP_PERRORP 0x08 /* unchanged input, active low */ 43 44 /* timeout for each character. This is relative to bus cycles -- it 45 * is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you 46 * have extremely slow printing, or if the machine seems to slow down 47 * a lot when you print. If you have slow printing, increase this 48 * number and recompile, and if your system gets bogged down, decrease 49 * this number. This can be changed with the tunelp(8) command as well. 50 */ 51 52 #define LP_INIT_CHAR 1000 53 54 /* The parallel port specs apparently say that there needs to be 55 * a .5usec wait before and after the strobe. 56 */ 57 58 #define LP_INIT_WAIT 1 59 60 /* This is the amount of time that the driver waits for the printer to 61 * catch up when the printer's buffer appears to be filled. If you 62 * want to tune this and have a fast printer (i.e. HPIIIP), decrease 63 * this number, and if you have a slow printer, increase this number. 64 * This is in hundredths of a second, the default 2 being .05 second. 65 * Or use the tunelp(8) command, which is especially nice if you want 66 * change back and forth between character and graphics printing, which 67 * are wildly different... 68 */ 69 70 #define LP_INIT_TIME 2 71 72 /* IOCTL numbers */ 73 #define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */ 74 #define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */ 75 #define LPABORT 0x0604 /* call with TRUE arg to abort on error, 76 FALSE to retry. Default is retry. */ 77 #define LPSETIRQ 0x0605 /* call with new IRQ number, 78 or 0 for polling (no IRQ) */ 79 #define LPGETIRQ 0x0606 /* get the current IRQ number */ 80 #define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */ 81 /* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */ 82 #define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off- 83 line, and error indicators good on all writes, 84 FALSE to ignore them. Default is ignore. */ 85 #define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error, 86 FALSE to ignore error. Default is ignore. */ 87 #define LPGETSTATUS 0x060b /* return LP_S(minor) */ 88 #define LPRESET 0x060c /* reset printer */ 89 #ifdef LP_STATS 90 #define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */ 91 #endif 92 #define LPGETFLAGS 0x060e /* get status flags */ 93 #define LPSETTIMEOUT_OLD 0x060f /* set parport timeout */ 94 #define LPSETTIMEOUT_NEW \ 95 _IOW(0x6, 0xf, __s64[2]) /* set parport timeout */ 96 #if __BITS_PER_LONG == 64 97 #define LPSETTIMEOUT LPSETTIMEOUT_OLD 98 #else 99 #define LPSETTIMEOUT (sizeof(time_t) > sizeof(__kernel_long_t) ? \ 100 LPSETTIMEOUT_NEW : LPSETTIMEOUT_OLD) 101 #endif 102 103 /* timeout for printk'ing a timeout, in jiffies (100ths of a second). 104 This is also used for re-checking error conditions if LP_ABORT is 105 not set. This is the default behavior. */ 106 107 #define LP_TIMEOUT_INTERRUPT (60 * HZ) 108 #define LP_TIMEOUT_POLLED (10 * HZ) 109 110 111 #endif /* _UAPI_LINUX_LP_H */