root/include/linux/phylink.h

/* [<][>][^][v][top][bottom][index][help] */

INCLUDED FROM


DEFINITIONS

This source file includes following definitions.
  1. phylink_autoneg_inband

   1 #ifndef NETDEV_PCS_H
   2 #define NETDEV_PCS_H
   3 
   4 #include <linux/phy.h>
   5 #include <linux/spinlock.h>
   6 #include <linux/workqueue.h>
   7 
   8 struct device_node;
   9 struct ethtool_cmd;
  10 struct fwnode_handle;
  11 struct net_device;
  12 
  13 enum {
  14         MLO_PAUSE_NONE,
  15         MLO_PAUSE_ASYM = BIT(0),
  16         MLO_PAUSE_SYM = BIT(1),
  17         MLO_PAUSE_RX = BIT(2),
  18         MLO_PAUSE_TX = BIT(3),
  19         MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX,
  20         MLO_PAUSE_AN = BIT(4),
  21 
  22         MLO_AN_PHY = 0, /* Conventional PHY */
  23         MLO_AN_FIXED,   /* Fixed-link mode */
  24         MLO_AN_INBAND,  /* In-band protocol */
  25 };
  26 
  27 static inline bool phylink_autoneg_inband(unsigned int mode)
  28 {
  29         return mode == MLO_AN_INBAND;
  30 }
  31 
  32 /**
  33  * struct phylink_link_state - link state structure
  34  * @advertising: ethtool bitmask containing advertised link modes
  35  * @lp_advertising: ethtool bitmask containing link partner advertised link
  36  *   modes
  37  * @interface: link &typedef phy_interface_t mode
  38  * @speed: link speed, one of the SPEED_* constants.
  39  * @duplex: link duplex mode, one of DUPLEX_* constants.
  40  * @pause: link pause state, described by MLO_PAUSE_* constants.
  41  * @link: true if the link is up.
  42  * @an_enabled: true if autonegotiation is enabled/desired.
  43  * @an_complete: true if autonegotiation has completed.
  44  */
  45 struct phylink_link_state {
  46         __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising);
  47         __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
  48         phy_interface_t interface;
  49         int speed;
  50         int duplex;
  51         int pause;
  52         unsigned int link:1;
  53         unsigned int an_enabled:1;
  54         unsigned int an_complete:1;
  55 };
  56 
  57 enum phylink_op_type {
  58         PHYLINK_NETDEV = 0,
  59         PHYLINK_DEV,
  60 };
  61 
  62 /**
  63  * struct phylink_config - PHYLINK configuration structure
  64  * @dev: a pointer to a struct device associated with the MAC
  65  * @type: operation type of PHYLINK instance
  66  */
  67 struct phylink_config {
  68         struct device *dev;
  69         enum phylink_op_type type;
  70 };
  71 
  72 /**
  73  * struct phylink_mac_ops - MAC operations structure.
  74  * @validate: Validate and update the link configuration.
  75  * @mac_link_state: Read the current link state from the hardware.
  76  * @mac_config: configure the MAC for the selected mode and state.
  77  * @mac_an_restart: restart 802.3z BaseX autonegotiation.
  78  * @mac_link_down: take the link down.
  79  * @mac_link_up: allow the link to come up.
  80  *
  81  * The individual methods are described more fully below.
  82  */
  83 struct phylink_mac_ops {
  84         void (*validate)(struct phylink_config *config,
  85                          unsigned long *supported,
  86                          struct phylink_link_state *state);
  87         int (*mac_link_state)(struct phylink_config *config,
  88                               struct phylink_link_state *state);
  89         void (*mac_config)(struct phylink_config *config, unsigned int mode,
  90                            const struct phylink_link_state *state);
  91         void (*mac_an_restart)(struct phylink_config *config);
  92         void (*mac_link_down)(struct phylink_config *config, unsigned int mode,
  93                               phy_interface_t interface);
  94         void (*mac_link_up)(struct phylink_config *config, unsigned int mode,
  95                             phy_interface_t interface,
  96                             struct phy_device *phy);
  97 };
  98 
  99 #if 0 /* For kernel-doc purposes only. */
 100 /**
 101  * validate - Validate and update the link configuration
 102  * @config: a pointer to a &struct phylink_config.
 103  * @supported: ethtool bitmask for supported link modes.
 104  * @state: a pointer to a &struct phylink_link_state.
 105  *
 106  * Clear bits in the @supported and @state->advertising masks that
 107  * are not supportable by the MAC.
 108  *
 109  * Note that the PHY may be able to transform from one connection
 110  * technology to another, so, eg, don't clear 1000BaseX just
 111  * because the MAC is unable to BaseX mode. This is more about
 112  * clearing unsupported speeds and duplex settings. The port modes
 113  * should not be cleared; phylink_set_port_modes() will help with this.
 114  *
 115  * If the @state->interface mode is %PHY_INTERFACE_MODE_1000BASEX
 116  * or %PHY_INTERFACE_MODE_2500BASEX, select the appropriate mode
 117  * based on @state->advertising and/or @state->speed and update
 118  * @state->interface accordingly. See phylink_helper_basex_speed().
 119  *
 120  * When @state->interface is %PHY_INTERFACE_MODE_NA, phylink expects the
 121  * MAC driver to return all supported link modes.
 122  *
 123  * If the @state->interface mode is not supported, then the @supported
 124  * mask must be cleared.
 125  */
 126 void validate(struct phylink_config *config, unsigned long *supported,
 127               struct phylink_link_state *state);
 128 
 129 /**
 130  * mac_link_state() - Read the current link state from the hardware
 131  * @config: a pointer to a &struct phylink_config.
 132  * @state: a pointer to a &struct phylink_link_state.
 133  *
 134  * Read the current link state from the MAC, reporting the current
 135  * speed in @state->speed, duplex mode in @state->duplex, pause mode
 136  * in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits,
 137  * negotiation completion state in @state->an_complete, and link
 138  * up state in @state->link.
 139  */
 140 int mac_link_state(struct phylink_config *config,
 141                    struct phylink_link_state *state);
 142 
 143 /**
 144  * mac_config() - configure the MAC for the selected mode and state
 145  * @config: a pointer to a &struct phylink_config.
 146  * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND.
 147  * @state: a pointer to a &struct phylink_link_state.
 148  *
 149  * Note - not all members of @state are valid.  In particular,
 150  * @state->lp_advertising, @state->link, @state->an_complete are never
 151  * guaranteed to be correct, and so any mac_config() implementation must
 152  * never reference these fields.
 153  *
 154  * The action performed depends on the currently selected mode:
 155  *
 156  * %MLO_AN_FIXED, %MLO_AN_PHY:
 157  *   Configure the specified @state->speed, @state->duplex and
 158  *   @state->pause (%MLO_PAUSE_TX / %MLO_PAUSE_RX) modes over a link
 159  *   specified by @state->interface.  @state->advertising may be used,
 160  *   but is not required.  Other members of @state must be ignored.
 161  *
 162  *   Valid state members: interface, speed, duplex, pause, advertising.
 163  *
 164  * %MLO_AN_INBAND:
 165  *   place the link in an inband negotiation mode (such as 802.3z
 166  *   1000base-X or Cisco SGMII mode depending on the @state->interface
 167  *   mode). In both cases, link state management (whether the link
 168  *   is up or not) is performed by the MAC, and reported via the
 169  *   mac_link_state() callback. Changes in link state must be made
 170  *   by calling phylink_mac_change().
 171  *
 172  *   If in 802.3z mode, the link speed is fixed, dependent on the
 173  *   @state->interface. Duplex is negotiated, and pause is advertised
 174  *   according to @state->an_enabled, @state->pause and
 175  *   @state->advertising flags. Beware of MACs which only support full
 176  *   duplex at gigabit and higher speeds.
 177  *
 178  *   If in Cisco SGMII mode, the link speed and duplex mode are passed
 179  *   in the serial bitstream 16-bit configuration word, and the MAC
 180  *   should be configured to read these bits and acknowledge the
 181  *   configuration word. Nothing is advertised by the MAC. The MAC is
 182  *   responsible for reading the configuration word and configuring
 183  *   itself accordingly.
 184  *
 185  *   Valid state members: interface, an_enabled, pause, advertising.
 186  *
 187  * Implementations are expected to update the MAC to reflect the
 188  * requested settings - i.o.w., if nothing has changed between two
 189  * calls, no action is expected.  If only flow control settings have
 190  * changed, flow control should be updated *without* taking the link
 191  * down.  This "update" behaviour is critical to avoid bouncing the
 192  * link up status.
 193  */
 194 void mac_config(struct phylink_config *config, unsigned int mode,
 195                 const struct phylink_link_state *state);
 196 
 197 /**
 198  * mac_an_restart() - restart 802.3z BaseX autonegotiation
 199  * @config: a pointer to a &struct phylink_config.
 200  */
 201 void mac_an_restart(struct phylink_config *config);
 202 
 203 /**
 204  * mac_link_down() - take the link down
 205  * @config: a pointer to a &struct phylink_config.
 206  * @mode: link autonegotiation mode
 207  * @interface: link &typedef phy_interface_t mode
 208  *
 209  * If @mode is not an in-band negotiation mode (as defined by
 210  * phylink_autoneg_inband()), force the link down and disable any
 211  * Energy Efficient Ethernet MAC configuration. Interface type
 212  * selection must be done in mac_config().
 213  */
 214 void mac_link_down(struct phylink_config *config, unsigned int mode,
 215                    phy_interface_t interface);
 216 
 217 /**
 218  * mac_link_up() - allow the link to come up
 219  * @config: a pointer to a &struct phylink_config.
 220  * @mode: link autonegotiation mode
 221  * @interface: link &typedef phy_interface_t mode
 222  * @phy: any attached phy
 223  *
 224  * If @mode is not an in-band negotiation mode (as defined by
 225  * phylink_autoneg_inband()), allow the link to come up. If @phy
 226  * is non-%NULL, configure Energy Efficient Ethernet by calling
 227  * phy_init_eee() and perform appropriate MAC configuration for EEE.
 228  * Interface type selection must be done in mac_config().
 229  */
 230 void mac_link_up(struct phylink_config *config, unsigned int mode,
 231                  phy_interface_t interface,
 232                  struct phy_device *phy);
 233 #endif
 234 
 235 struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *,
 236                                phy_interface_t iface,
 237                                const struct phylink_mac_ops *ops);
 238 void phylink_destroy(struct phylink *);
 239 
 240 int phylink_connect_phy(struct phylink *, struct phy_device *);
 241 int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags);
 242 void phylink_disconnect_phy(struct phylink *);
 243 int phylink_fixed_state_cb(struct phylink *,
 244                            void (*cb)(struct net_device *dev,
 245                                       struct phylink_link_state *));
 246 
 247 void phylink_mac_change(struct phylink *, bool up);
 248 
 249 void phylink_start(struct phylink *);
 250 void phylink_stop(struct phylink *);
 251 
 252 void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *);
 253 int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *);
 254 
 255 int phylink_ethtool_ksettings_get(struct phylink *,
 256                                   struct ethtool_link_ksettings *);
 257 int phylink_ethtool_ksettings_set(struct phylink *,
 258                                   const struct ethtool_link_ksettings *);
 259 int phylink_ethtool_nway_reset(struct phylink *);
 260 void phylink_ethtool_get_pauseparam(struct phylink *,
 261                                     struct ethtool_pauseparam *);
 262 int phylink_ethtool_set_pauseparam(struct phylink *,
 263                                    struct ethtool_pauseparam *);
 264 int phylink_get_eee_err(struct phylink *);
 265 int phylink_init_eee(struct phylink *, bool);
 266 int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *);
 267 int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *);
 268 int phylink_mii_ioctl(struct phylink *, struct ifreq *, int);
 269 
 270 #define phylink_zero(bm) \
 271         bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS)
 272 #define __phylink_do_bit(op, bm, mode) \
 273         op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm)
 274 
 275 #define phylink_set(bm, mode)   __phylink_do_bit(__set_bit, bm, mode)
 276 #define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode)
 277 #define phylink_test(bm, mode)  __phylink_do_bit(test_bit, bm, mode)
 278 
 279 void phylink_set_port_modes(unsigned long *bits);
 280 void phylink_helper_basex_speed(struct phylink_link_state *state);
 281 
 282 #endif

/* [<][>][^][v][top][bottom][index][help] */