root/include/linux/mmc/sdio.h

INCLUDED FROM

   1 /* SPDX-License-Identifier: GPL-2.0-or-later */
   2 /*
   3  *  include/linux/mmc/sdio.h
   4  *
   5  *  Copyright 2006-2007 Pierre Ossman
   6  */
   7 
   8 #ifndef LINUX_MMC_SDIO_H
   9 #define LINUX_MMC_SDIO_H
  10 
  11 /* SDIO commands                         type  argument     response */
  12 #define SD_IO_SEND_OP_COND          5 /* bcr  [23:0] OCR         R4  */
  13 #define SD_IO_RW_DIRECT            52 /* ac   [31:0] See below   R5  */
  14 #define SD_IO_RW_EXTENDED          53 /* adtc [31:0] See below   R5  */
  15 
  16 /*
  17  * SD_IO_RW_DIRECT argument format:
  18  *
  19  *      [31] R/W flag
  20  *      [30:28] Function number
  21  *      [27] RAW flag
  22  *      [25:9] Register address
  23  *      [7:0] Data
  24  */
  25 
  26 /*
  27  * SD_IO_RW_EXTENDED argument format:
  28  *
  29  *      [31] R/W flag
  30  *      [30:28] Function number
  31  *      [27] Block mode
  32  *      [26] Increment address
  33  *      [25:9] Register address
  34  *      [8:0] Byte/block count
  35  */
  36 
  37 #define R4_18V_PRESENT (1<<24)
  38 #define R4_MEMORY_PRESENT (1 << 27)
  39 
  40 /*
  41   SDIO status in R5
  42   Type
  43         e : error bit
  44         s : status bit
  45         r : detected and set for the actual command response
  46         x : detected and set during command execution. the host must poll
  47             the card by sending status command in order to read these bits.
  48   Clear condition
  49         a : according to the card state
  50         b : always related to the previous command. Reception of
  51             a valid command will clear it (with a delay of one command)
  52         c : clear by read
  53  */
  54 
  55 #define R5_COM_CRC_ERROR        (1 << 15)       /* er, b */
  56 #define R5_ILLEGAL_COMMAND      (1 << 14)       /* er, b */
  57 #define R5_ERROR                (1 << 11)       /* erx, c */
  58 #define R5_FUNCTION_NUMBER      (1 << 9)        /* er, c */
  59 #define R5_OUT_OF_RANGE         (1 << 8)        /* er, c */
  60 #define R5_STATUS(x)            (x & 0xCB00)
  61 #define R5_IO_CURRENT_STATE(x)  ((x & 0x3000) >> 12) /* s, b */
  62 
  63 /*
  64  * Card Common Control Registers (CCCR)
  65  */
  66 
  67 #define SDIO_CCCR_CCCR          0x00
  68 
  69 #define  SDIO_CCCR_REV_1_00     0       /* CCCR/FBR Version 1.00 */
  70 #define  SDIO_CCCR_REV_1_10     1       /* CCCR/FBR Version 1.10 */
  71 #define  SDIO_CCCR_REV_1_20     2       /* CCCR/FBR Version 1.20 */
  72 #define  SDIO_CCCR_REV_3_00     3       /* CCCR/FBR Version 3.00 */
  73 
  74 #define  SDIO_SDIO_REV_1_00     0       /* SDIO Spec Version 1.00 */
  75 #define  SDIO_SDIO_REV_1_10     1       /* SDIO Spec Version 1.10 */
  76 #define  SDIO_SDIO_REV_1_20     2       /* SDIO Spec Version 1.20 */
  77 #define  SDIO_SDIO_REV_2_00     3       /* SDIO Spec Version 2.00 */
  78 #define  SDIO_SDIO_REV_3_00     4       /* SDIO Spec Version 3.00 */
  79 
  80 #define SDIO_CCCR_SD            0x01
  81 
  82 #define  SDIO_SD_REV_1_01       0       /* SD Physical Spec Version 1.01 */
  83 #define  SDIO_SD_REV_1_10       1       /* SD Physical Spec Version 1.10 */
  84 #define  SDIO_SD_REV_2_00       2       /* SD Physical Spec Version 2.00 */
  85 #define  SDIO_SD_REV_3_00       3       /* SD Physical Spev Version 3.00 */
  86 
  87 #define SDIO_CCCR_IOEx          0x02
  88 #define SDIO_CCCR_IORx          0x03
  89 
  90 #define SDIO_CCCR_IENx          0x04    /* Function/Master Interrupt Enable */
  91 #define SDIO_CCCR_INTx          0x05    /* Function Interrupt Pending */
  92 
  93 #define SDIO_CCCR_ABORT         0x06    /* function abort/card reset */
  94 
  95 #define SDIO_CCCR_IF            0x07    /* bus interface controls */
  96 
  97 #define  SDIO_BUS_WIDTH_MASK    0x03    /* data bus width setting */
  98 #define  SDIO_BUS_WIDTH_1BIT    0x00
  99 #define  SDIO_BUS_WIDTH_RESERVED 0x01
 100 #define  SDIO_BUS_WIDTH_4BIT    0x02
 101 #define  SDIO_BUS_ECSI          0x20    /* Enable continuous SPI interrupt */
 102 #define  SDIO_BUS_SCSI          0x40    /* Support continuous SPI interrupt */
 103 
 104 #define  SDIO_BUS_ASYNC_INT     0x20
 105 
 106 #define  SDIO_BUS_CD_DISABLE     0x80   /* disable pull-up on DAT3 (pin 1) */
 107 
 108 #define SDIO_CCCR_CAPS          0x08
 109 
 110 #define  SDIO_CCCR_CAP_SDC      0x01    /* can do CMD52 while data transfer */
 111 #define  SDIO_CCCR_CAP_SMB      0x02    /* can do multi-block xfers (CMD53) */
 112 #define  SDIO_CCCR_CAP_SRW      0x04    /* supports read-wait protocol */
 113 #define  SDIO_CCCR_CAP_SBS      0x08    /* supports suspend/resume */
 114 #define  SDIO_CCCR_CAP_S4MI     0x10    /* interrupt during 4-bit CMD53 */
 115 #define  SDIO_CCCR_CAP_E4MI     0x20    /* enable ints during 4-bit CMD53 */
 116 #define  SDIO_CCCR_CAP_LSC      0x40    /* low speed card */
 117 #define  SDIO_CCCR_CAP_4BLS     0x80    /* 4 bit low speed card */
 118 
 119 #define SDIO_CCCR_CIS           0x09    /* common CIS pointer (3 bytes) */
 120 
 121 /* Following 4 regs are valid only if SBS is set */
 122 #define SDIO_CCCR_SUSPEND       0x0c
 123 #define SDIO_CCCR_SELx          0x0d
 124 #define SDIO_CCCR_EXECx         0x0e
 125 #define SDIO_CCCR_READYx        0x0f
 126 
 127 #define SDIO_CCCR_BLKSIZE       0x10
 128 
 129 #define SDIO_CCCR_POWER         0x12
 130 
 131 #define  SDIO_POWER_SMPC        0x01    /* Supports Master Power Control */
 132 #define  SDIO_POWER_EMPC        0x02    /* Enable Master Power Control */
 133 
 134 #define SDIO_CCCR_SPEED         0x13
 135 
 136 #define  SDIO_SPEED_SHS         0x01    /* Supports High-Speed mode */
 137 #define  SDIO_SPEED_BSS_SHIFT   1
 138 #define  SDIO_SPEED_BSS_MASK    (7<<SDIO_SPEED_BSS_SHIFT)
 139 #define  SDIO_SPEED_SDR12       (0<<SDIO_SPEED_BSS_SHIFT)
 140 #define  SDIO_SPEED_SDR25       (1<<SDIO_SPEED_BSS_SHIFT)
 141 #define  SDIO_SPEED_SDR50       (2<<SDIO_SPEED_BSS_SHIFT)
 142 #define  SDIO_SPEED_SDR104      (3<<SDIO_SPEED_BSS_SHIFT)
 143 #define  SDIO_SPEED_DDR50       (4<<SDIO_SPEED_BSS_SHIFT)
 144 #define  SDIO_SPEED_EHS         SDIO_SPEED_SDR25        /* Enable High-Speed */
 145 
 146 #define SDIO_CCCR_UHS           0x14
 147 #define  SDIO_UHS_SDR50         0x01
 148 #define  SDIO_UHS_SDR104        0x02
 149 #define  SDIO_UHS_DDR50         0x04
 150 
 151 #define SDIO_CCCR_DRIVE_STRENGTH 0x15
 152 #define  SDIO_SDTx_MASK         0x07
 153 #define  SDIO_DRIVE_SDTA        (1<<0)
 154 #define  SDIO_DRIVE_SDTC        (1<<1)
 155 #define  SDIO_DRIVE_SDTD        (1<<2)
 156 #define  SDIO_DRIVE_DTSx_MASK   0x03
 157 #define  SDIO_DRIVE_DTSx_SHIFT  4
 158 #define  SDIO_DTSx_SET_TYPE_B   (0 << SDIO_DRIVE_DTSx_SHIFT)
 159 #define  SDIO_DTSx_SET_TYPE_A   (1 << SDIO_DRIVE_DTSx_SHIFT)
 160 #define  SDIO_DTSx_SET_TYPE_C   (2 << SDIO_DRIVE_DTSx_SHIFT)
 161 #define  SDIO_DTSx_SET_TYPE_D   (3 << SDIO_DRIVE_DTSx_SHIFT)
 162 /*
 163  * Function Basic Registers (FBR)
 164  */
 165 
 166 #define SDIO_FBR_BASE(f)        ((f) * 0x100) /* base of function f's FBRs */
 167 
 168 #define SDIO_FBR_STD_IF         0x00
 169 
 170 #define  SDIO_FBR_SUPPORTS_CSA  0x40    /* supports Code Storage Area */
 171 #define  SDIO_FBR_ENABLE_CSA    0x80    /* enable Code Storage Area */
 172 
 173 #define SDIO_FBR_STD_IF_EXT     0x01
 174 
 175 #define SDIO_FBR_POWER          0x02
 176 
 177 #define  SDIO_FBR_POWER_SPS     0x01    /* Supports Power Selection */
 178 #define  SDIO_FBR_POWER_EPS     0x02    /* Enable (low) Power Selection */
 179 
 180 #define SDIO_FBR_CIS            0x09    /* CIS pointer (3 bytes) */
 181 
 182 
 183 #define SDIO_FBR_CSA            0x0C    /* CSA pointer (3 bytes) */
 184 
 185 #define SDIO_FBR_CSA_DATA       0x0F
 186 
 187 #define SDIO_FBR_BLKSIZE        0x10    /* block size (2 bytes) */
 188 
 189 #endif /* LINUX_MMC_SDIO_H */