root/include/media/i2c/saa7115.h

/* [<][>][^][v][top][bottom][index][help] */

INCLUDED FROM


   1 /* SPDX-License-Identifier: GPL-2.0-or-later */
   2 /*
   3     saa7115.h - definition for saa7111/3/4/5 inputs and frequency flags
   4 
   5     Copyright (C) 2006 Hans Verkuil (hverkuil@xs4all.nl)
   6 
   7 */
   8 
   9 #ifndef _SAA7115_H_
  10 #define _SAA7115_H_
  11 
  12 /* s_routing inputs, outputs, and config */
  13 
  14 /* SAA7111/3/4/5 HW inputs */
  15 #define SAA7115_COMPOSITE0 0
  16 #define SAA7115_COMPOSITE1 1
  17 #define SAA7115_COMPOSITE2 2
  18 #define SAA7115_COMPOSITE3 3
  19 #define SAA7115_COMPOSITE4 4 /* not available for the saa7111/3 */
  20 #define SAA7115_COMPOSITE5 5 /* not available for the saa7111/3 */
  21 #define SAA7115_SVIDEO0    6
  22 #define SAA7115_SVIDEO1    7
  23 #define SAA7115_SVIDEO2    8
  24 #define SAA7115_SVIDEO3    9
  25 
  26 /* outputs */
  27 #define SAA7115_IPORT_ON        1
  28 #define SAA7115_IPORT_OFF       0
  29 
  30 /* SAA7111 specific outputs. */
  31 #define SAA7111_VBI_BYPASS      2
  32 #define SAA7111_FMT_YUV422      0x00
  33 #define SAA7111_FMT_RGB         0x40
  34 #define SAA7111_FMT_CCIR        0x80
  35 #define SAA7111_FMT_YUV411      0xc0
  36 
  37 /* config flags */
  38 /*
  39  * Register 0x85 should set bit 0 to 0 (it's 1 by default). This bit
  40  * controls the IDQ signal polarity which is set to 'inverted' if the bit
  41  * it 1 and to 'default' if it is 0.
  42  */
  43 #define SAA7115_IDQ_IS_DEFAULT  (1 << 0)
  44 
  45 /* s_crystal_freq values and flags */
  46 
  47 /* SAA7115 v4l2_crystal_freq frequency values */
  48 #define SAA7115_FREQ_32_11_MHZ  32110000   /* 32.11 MHz crystal, SAA7114/5 only */
  49 #define SAA7115_FREQ_24_576_MHZ 24576000   /* 24.576 MHz crystal */
  50 
  51 /* SAA7115 v4l2_crystal_freq audio clock control flags */
  52 #define SAA7115_FREQ_FL_UCGC         (1 << 0) /* SA 3A[7], UCGC, SAA7115 only */
  53 #define SAA7115_FREQ_FL_CGCDIV       (1 << 1) /* SA 3A[6], CGCDIV, SAA7115 only */
  54 #define SAA7115_FREQ_FL_APLL         (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */
  55 #define SAA7115_FREQ_FL_DOUBLE_ASCLK (1 << 3) /* SA 39, LRDIV, SAA7114/5 only */
  56 
  57 /* ===== SAA7113 Config enums ===== */
  58 
  59 /* Register 0x08 "Horizontal time constant" [Bit 3..4]:
  60  * Should be set to "Fast Locking Mode" according to the datasheet,
  61  * and that is the default setting in the gm7113c_init table.
  62  * saa7113_init sets this value to "VTR Mode". */
  63 enum saa7113_r08_htc {
  64         SAA7113_HTC_TV_MODE = 0x00,
  65         SAA7113_HTC_VTR_MODE,                   /* Default for saa7113_init */
  66         SAA7113_HTC_FAST_LOCKING_MODE = 0x03    /* Default for gm7113c_init */
  67 };
  68 
  69 /* Register 0x10 "Output format selection" [Bit 6..7]:
  70  * Defaults to ITU_656 as specified in datasheet. */
  71 enum saa7113_r10_ofts {
  72         SAA7113_OFTS_ITU_656 = 0x0,     /* Default */
  73         SAA7113_OFTS_VFLAG_BY_VREF,
  74         SAA7113_OFTS_VFLAG_BY_DATA_TYPE
  75 };
  76 
  77 /*
  78  * Register 0x12 "Output control" [Bit 0..3 Or Bit 4..7]:
  79  * This is used to select what data is output on the RTS0 and RTS1 pins.
  80  * RTS1 [Bit 4..7] Defaults to DOT_IN. (This value can not be set for RTS0)
  81  * RTS0 [Bit 0..3] Defaults to VIPB in gm7113c_init as specified
  82  * in the datasheet, but is set to HREF_HS in the saa7113_init table.
  83  */
  84 enum saa7113_r12_rts {
  85         SAA7113_RTS_DOT_IN = 0,         /* OBS: Only for RTS1 (Default RTS1) */
  86         SAA7113_RTS_VIPB,               /* Default RTS0 For gm7113c_init */
  87         SAA7113_RTS_GPSW,
  88         SAA7115_RTS_HL,
  89         SAA7113_RTS_VL,
  90         SAA7113_RTS_DL,
  91         SAA7113_RTS_PLIN,
  92         SAA7113_RTS_HREF_HS,            /* Default RTS0 For saa7113_init */
  93         SAA7113_RTS_HS,
  94         SAA7113_RTS_HQ,
  95         SAA7113_RTS_ODD,
  96         SAA7113_RTS_VS,
  97         SAA7113_RTS_V123,
  98         SAA7113_RTS_VGATE,
  99         SAA7113_RTS_VREF,
 100         SAA7113_RTS_FID
 101 };
 102 
 103 /**
 104  * struct saa7115_platform_data - Allow overriding default initialization
 105  *
 106  * @saa7113_force_gm7113c_init: Force the use of the gm7113c_init table
 107  *                              instead of saa7113_init table
 108  *                              (saa7113 only)
 109  * @saa7113_r08_htc:            [R_08 - Bit 3..4]
 110  * @saa7113_r10_vrln:           [R_10 - Bit 3]
 111  *                              default: Disabled for gm7113c_init
 112  *                                       Enabled for saa7113c_init
 113  * @saa7113_r10_ofts:           [R_10 - Bit 6..7]
 114  * @saa7113_r12_rts0:           [R_12 - Bit 0..3]
 115  * @saa7113_r12_rts1:           [R_12 - Bit 4..7]
 116  * @saa7113_r13_adlsb:          [R_13 - Bit 7] - default: disabled
 117  */
 118 struct saa7115_platform_data {
 119         bool saa7113_force_gm7113c_init;
 120         enum saa7113_r08_htc *saa7113_r08_htc;
 121         bool *saa7113_r10_vrln;
 122         enum saa7113_r10_ofts *saa7113_r10_ofts;
 123         enum saa7113_r12_rts *saa7113_r12_rts0;
 124         enum saa7113_r12_rts *saa7113_r12_rts1;
 125         bool *saa7113_r13_adlsb;
 126 };
 127 
 128 #endif

/* [<][>][^][v][top][bottom][index][help] */