root/drivers/net/ethernet/amd/7990.h

/* [<][>][^][v][top][bottom][index][help] */

INCLUDED FROM


   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 /*
   3  * 7990.h -- LANCE ethernet IC generic routines.
   4  * This is an attempt to separate out the bits of various ethernet
   5  * drivers that are common because they all use the AMD 7990 LANCE
   6  * (Local Area Network Controller for Ethernet) chip.
   7  *
   8  * Copyright (C) 05/1998 Peter Maydell <pmaydell@chiark.greenend.org.uk>
   9  *
  10  * Most of this stuff was obtained by looking at other LANCE drivers,
  11  * in particular a2065.[ch]. The AMD C-LANCE datasheet was also helpful.
  12  */
  13 
  14 #ifndef _7990_H
  15 #define _7990_H
  16 
  17 /* The lance only has two register locations. We communicate mostly via memory. */
  18 #define LANCE_RDP       0       /* Register Data Port */
  19 #define LANCE_RAP       2       /* Register Address Port */
  20 
  21 /* Transmit/receive ring definitions.
  22  * We allow the specific drivers to override these defaults if they want to.
  23  * NB: according to lance.c, increasing the number of buffers is a waste
  24  * of space and reduces the chance that an upper layer will be able to
  25  * reorder queued Tx packets based on priority. [Clearly there is a minimum
  26  * limit too: too small and we drop rx packets and can't tx at full speed.]
  27  * 4+4 seems to be the usual setting; the atarilance driver uses 3 and 5.
  28  */
  29 
  30 /* Blast! This won't work. The problem is that we can't specify a default
  31  * setting because that would cause the lance_init_block struct to be
  32  * too long (and overflow the RAM on shared-memory cards like the HP LANCE.
  33  */
  34 #ifndef LANCE_LOG_TX_BUFFERS
  35 #define LANCE_LOG_TX_BUFFERS 1
  36 #define LANCE_LOG_RX_BUFFERS 3
  37 #endif
  38 
  39 #define TX_RING_SIZE            (1 << LANCE_LOG_TX_BUFFERS)
  40 #define RX_RING_SIZE            (1 << LANCE_LOG_RX_BUFFERS)
  41 #define TX_RING_MOD_MASK        (TX_RING_SIZE - 1)
  42 #define RX_RING_MOD_MASK        (RX_RING_SIZE - 1)
  43 #define TX_RING_LEN_BITS        ((LANCE_LOG_TX_BUFFERS) << 29)
  44 #define RX_RING_LEN_BITS        ((LANCE_LOG_RX_BUFFERS) << 29)
  45 #define PKT_BUFF_SIZE           (1544)
  46 #define RX_BUFF_SIZE            PKT_BUFF_SIZE
  47 #define TX_BUFF_SIZE            PKT_BUFF_SIZE
  48 
  49 /* Each receive buffer is described by a receive message descriptor (RMD) */
  50 struct lance_rx_desc {
  51         volatile unsigned short rmd0;       /* low address of packet */
  52         volatile unsigned char  rmd1_bits;  /* descriptor bits */
  53         volatile unsigned char  rmd1_hadr;  /* high address of packet */
  54         volatile short    length;           /* This length is 2s complement (negative)!
  55                                              * Buffer length */
  56         volatile unsigned short mblength;   /* Actual number of bytes received */
  57 };
  58 
  59 /* Ditto for TMD: */
  60 struct lance_tx_desc {
  61         volatile unsigned short tmd0;       /* low address of packet */
  62         volatile unsigned char  tmd1_bits;  /* descriptor bits */
  63         volatile unsigned char  tmd1_hadr;  /* high address of packet */
  64         volatile short    length;           /* Length is 2s complement (negative)! */
  65         volatile unsigned short misc;
  66 };
  67 
  68 /* There are three memory structures accessed by the LANCE:
  69  * the initialization block, the receive and transmit descriptor rings,
  70  * and the data buffers themselves. In fact we might as well put the
  71  * init block,the Tx and Rx rings and the buffers together in memory:
  72  */
  73 struct lance_init_block {
  74         volatile unsigned short mode;           /* Pre-set mode (reg. 15) */
  75         volatile unsigned char phys_addr[6];    /* Physical ethernet address */
  76         volatile unsigned filter[2];            /* Multicast filter (64 bits) */
  77 
  78         /* Receive and transmit ring base, along with extra bits. */
  79         volatile unsigned short rx_ptr;         /* receive descriptor addr */
  80         volatile unsigned short rx_len;         /* receive len and high addr */
  81         volatile unsigned short tx_ptr;         /* transmit descriptor addr */
  82         volatile unsigned short tx_len;         /* transmit len and high addr */
  83 
  84         /* The Tx and Rx ring entries must be aligned on 8-byte boundaries.
  85          * This will be true if this whole struct is 8-byte aligned.
  86          */
  87         volatile struct lance_tx_desc btx_ring[TX_RING_SIZE];
  88         volatile struct lance_rx_desc brx_ring[RX_RING_SIZE];
  89 
  90         volatile char tx_buf[TX_RING_SIZE][TX_BUFF_SIZE];
  91         volatile char rx_buf[RX_RING_SIZE][RX_BUFF_SIZE];
  92         /* we use this just to make the struct big enough that we can move its startaddr
  93          * in order to force alignment to an eight byte boundary.
  94          */
  95 };
  96 
  97 /* This is where we keep all the stuff the driver needs to know about.
  98  * I'm definitely unhappy about the mechanism for allowing specific
  99  * drivers to add things...
 100  */
 101 struct lance_private {
 102         const char *name;
 103         unsigned long base;
 104         volatile struct lance_init_block *init_block; /* CPU address of RAM */
 105         volatile struct lance_init_block *lance_init_block; /* LANCE address of RAM */
 106 
 107         int rx_new, tx_new;
 108         int rx_old, tx_old;
 109 
 110         int lance_log_rx_bufs, lance_log_tx_bufs;
 111         int rx_ring_mod_mask, tx_ring_mod_mask;
 112 
 113         int tpe;                        /* TPE is selected */
 114         int auto_select;                /* cable-selection is by carrier */
 115         unsigned short busmaster_regval;
 116 
 117         unsigned int irq;               /* IRQ to register */
 118 
 119         /* This is because the HP LANCE is disgusting and you have to check
 120          * a DIO-specific register every time you read/write the LANCE regs :-<
 121          * [could we get away with making these some sort of macro?]
 122          */
 123         void (*writerap)(void *, unsigned short);
 124         void (*writerdp)(void *, unsigned short);
 125         unsigned short (*readrdp)(void *);
 126         spinlock_t devlock;
 127         char tx_full;
 128 };
 129 
 130 /*
 131  *              Am7990 Control and Status Registers
 132  */
 133 #define LE_CSR0         0x0000  /* LANCE Controller Status */
 134 #define LE_CSR1         0x0001  /* IADR[15:0] (bit0==0 ie word aligned) */
 135 #define LE_CSR2         0x0002  /* IADR[23:16] (high bits reserved) */
 136 #define LE_CSR3         0x0003  /* Misc */
 137 
 138 /*
 139  *              Bit definitions for CSR0 (LANCE Controller Status)
 140  */
 141 #define LE_C0_ERR       0x8000  /* Error = BABL | CERR | MISS | MERR */
 142 #define LE_C0_BABL      0x4000  /* Babble: Transmitted too many bits */
 143 #define LE_C0_CERR      0x2000  /* No Heartbeat (10BASE-T) */
 144 #define LE_C0_MISS      0x1000  /* Missed Frame (no rx buffer to put it in) */
 145 #define LE_C0_MERR      0x0800  /* Memory Error */
 146 #define LE_C0_RINT      0x0400  /* Receive Interrupt */
 147 #define LE_C0_TINT      0x0200  /* Transmit Interrupt */
 148 #define LE_C0_IDON      0x0100  /* Initialization Done */
 149 #define LE_C0_INTR      0x0080  /* Interrupt Flag
 150                                    = BABL | MISS | MERR | RINT | TINT | IDON */
 151 #define LE_C0_INEA      0x0040  /* Interrupt Enable */
 152 #define LE_C0_RXON      0x0020  /* Receive On */
 153 #define LE_C0_TXON      0x0010  /* Transmit On */
 154 #define LE_C0_TDMD      0x0008  /* Transmit Demand */
 155 #define LE_C0_STOP      0x0004  /* Stop */
 156 #define LE_C0_STRT      0x0002  /* Start */
 157 #define LE_C0_INIT      0x0001  /* Initialize */
 158 
 159 
 160 /*
 161  *              Bit definitions for CSR3
 162  */
 163 #define LE_C3_BSWP      0x0004  /* Byte Swap (on for big endian byte order) */
 164 #define LE_C3_ACON      0x0002  /* ALE Control (on for active low ALE) */
 165 #define LE_C3_BCON      0x0001  /* Byte Control */
 166 
 167 
 168 /*
 169  *              Mode Flags
 170  */
 171 #define LE_MO_PROM      0x8000  /* Promiscuous Mode */
 172 /* these next ones 0x4000 -- 0x0080 are not available on the LANCE 7990,
 173  * but they are in NetBSD's am7990.h, presumably for backwards-compatible chips
 174  */
 175 #define LE_MO_DRCVBC    0x4000  /* disable receive broadcast */
 176 #define LE_MO_DRCVPA    0x2000  /* disable physical address detection */
 177 #define LE_MO_DLNKTST   0x1000  /* disable link status */
 178 #define LE_MO_DAPC      0x0800  /* disable automatic polarity correction */
 179 #define LE_MO_MENDECL   0x0400  /* MENDEC loopback mode */
 180 #define LE_MO_LRTTSEL   0x0200  /* lower RX threshold / TX mode selection */
 181 #define LE_MO_PSEL1     0x0100  /* port selection bit1 */
 182 #define LE_MO_PSEL0     0x0080  /* port selection bit0 */
 183 /* and this one is from the C-LANCE data sheet... */
 184 #define LE_MO_EMBA      0x0080  /* Enable Modified Backoff Algorithm
 185                                    (C-LANCE, not original LANCE) */
 186 #define LE_MO_INTL      0x0040  /* Internal Loopback */
 187 #define LE_MO_DRTY      0x0020  /* Disable Retry */
 188 #define LE_MO_FCOLL     0x0010  /* Force Collision */
 189 #define LE_MO_DXMTFCS   0x0008  /* Disable Transmit CRC */
 190 #define LE_MO_LOOP      0x0004  /* Loopback Enable */
 191 #define LE_MO_DTX       0x0002  /* Disable Transmitter */
 192 #define LE_MO_DRX       0x0001  /* Disable Receiver */
 193 
 194 
 195 /*
 196  *              Receive Flags
 197  */
 198 #define LE_R1_OWN       0x80    /* LANCE owns the descriptor */
 199 #define LE_R1_ERR       0x40    /* Error */
 200 #define LE_R1_FRA       0x20    /* Framing Error */
 201 #define LE_R1_OFL       0x10    /* Overflow Error */
 202 #define LE_R1_CRC       0x08    /* CRC Error */
 203 #define LE_R1_BUF       0x04    /* Buffer Error */
 204 #define LE_R1_SOP       0x02    /* Start of Packet */
 205 #define LE_R1_EOP       0x01    /* End of Packet */
 206 #define LE_R1_POK       0x03    /* Packet is complete: SOP + EOP */
 207 
 208 
 209 /*
 210  *              Transmit Flags
 211  */
 212 #define LE_T1_OWN       0x80    /* LANCE owns the descriptor */
 213 #define LE_T1_ERR       0x40    /* Error */
 214 #define LE_T1_RES       0x20    /* Reserved, LANCE writes this with a zero */
 215 #define LE_T1_EMORE     0x10    /* More than one retry needed */
 216 #define LE_T1_EONE      0x08    /* One retry needed */
 217 #define LE_T1_EDEF      0x04    /* Deferred */
 218 #define LE_T1_SOP       0x02    /* Start of Packet */
 219 #define LE_T1_EOP       0x01    /* End of Packet */
 220 #define LE_T1_POK       0x03    /* Packet is complete: SOP + EOP */
 221 
 222 /*
 223  *              Error Flags
 224  */
 225 #define LE_T3_BUF       0x8000  /* Buffer Error */
 226 #define LE_T3_UFL       0x4000  /* Underflow Error */
 227 #define LE_T3_LCOL      0x1000  /* Late Collision */
 228 #define LE_T3_CLOS      0x0800  /* Loss of Carrier */
 229 #define LE_T3_RTY       0x0400  /* Retry Error */
 230 #define LE_T3_TDR       0x03ff  /* Time Domain Reflectometry */
 231 
 232 /* Miscellaneous useful macros */
 233 
 234 #define TX_BUFFS_AVAIL ((lp->tx_old <= lp->tx_new) ? \
 235                         lp->tx_old + lp->tx_ring_mod_mask - lp->tx_new : \
 236                         lp->tx_old - lp->tx_new - 1)
 237 
 238 /* The LANCE only uses 24 bit addresses. This does the obvious thing. */
 239 #define LANCE_ADDR(x) ((int)(x) & ~0xff000000)
 240 
 241 /* Now the prototypes we export */
 242 int lance_open(struct net_device *dev);
 243 int lance_close(struct net_device *dev);
 244 int lance_start_xmit(struct sk_buff *skb, struct net_device *dev);
 245 void lance_set_multicast(struct net_device *dev);
 246 void lance_tx_timeout(struct net_device *dev);
 247 #ifdef CONFIG_NET_POLL_CONTROLLER
 248 void lance_poll(struct net_device *dev);
 249 #endif
 250 
 251 #endif /* ndef _7990_H */

/* [<][>][^][v][top][bottom][index][help] */