root/drivers/net/ethernet/smsc/smc9194.h

/* [<][>][^][v][top][bottom][index][help] */

INCLUDED FROM


   1 /*------------------------------------------------------------------------
   2  . smc9194.h
   3  . Copyright (C) 1996 by Erik Stahlman
   4  .
   5  . This software may be used and distributed according to the terms
   6  . of the GNU General Public License, incorporated herein by reference.
   7  .
   8  . This file contains register information and access macros for
   9  . the SMC91xxx chipset.
  10  .
  11  . Information contained in this file was obtained from the SMC91C94
  12  . manual from SMC.  To get a copy, if you really want one, you can find
  13  . information under www.smc.com in the components division.
  14  . ( this thanks to advice from Donald Becker ).
  15  .
  16  . Authors
  17  .      Erik Stahlman                           ( erik@vt.edu )
  18  .
  19  . History
  20  . 01/06/96              Erik Stahlman   moved definitions here from main .c file
  21  . 01/19/96              Erik Stahlman    polished this up some, and added better
  22  .                                                                                error handling
  23  .
  24  ---------------------------------------------------------------------------*/
  25 #ifndef _SMC9194_H_
  26 #define _SMC9194_H_
  27 
  28 /* I want some simple types */
  29 
  30 typedef unsigned char                   byte;
  31 typedef unsigned short                  word;
  32 typedef unsigned long int               dword;
  33 
  34 
  35 /* Because of bank switching, the SMC91xxx uses only 16 I/O ports */
  36 
  37 #define SMC_IO_EXTENT   16
  38 
  39 
  40 /*---------------------------------------------------------------
  41  .
  42  . A description of the SMC registers is probably in order here,
  43  . although for details, the SMC datasheet is invaluable.
  44  .
  45  . Basically, the chip has 4 banks of registers ( 0 to 3 ), which
  46  . are accessed by writing a number into the BANK_SELECT register
  47  . ( I also use a SMC_SELECT_BANK macro for this ).
  48  .
  49  . The banks are configured so that for most purposes, bank 2 is all
  50  . that is needed for simple run time tasks.
  51  -----------------------------------------------------------------------*/
  52 
  53 /*
  54  . Bank Select Register:
  55  .
  56  .              yyyy yyyy 0000 00xx
  57  .              xx              = bank number
  58  .              yyyy yyyy       = 0x33, for identification purposes.
  59 */
  60 #define BANK_SELECT             14
  61 
  62 /* BANK 0  */
  63 
  64 #define TCR             0       /* transmit control register */
  65 #define TCR_ENABLE      0x0001  /* if this is 1, we can transmit */
  66 #define TCR_FDUPLX      0x0800  /* receive packets sent out */
  67 #define TCR_STP_SQET    0x1000  /* stop transmitting if Signal quality error */
  68 #define TCR_MON_CNS     0x0400  /* monitors the carrier status */
  69 #define TCR_PAD_ENABLE  0x0080  /* pads short packets to 64 bytes */
  70 
  71 #define TCR_CLEAR       0       /* do NOTHING */
  72 /* the normal settings for the TCR register : */
  73 /* QUESTION: do I want to enable padding of short packets ? */
  74 #define TCR_NORMAL      TCR_ENABLE
  75 
  76 
  77 #define EPH_STATUS      2
  78 #define ES_LINK_OK      0x4000  /* is the link integrity ok ? */
  79 
  80 #define RCR             4
  81 #define RCR_SOFTRESET   0x8000  /* resets the chip */
  82 #define RCR_STRIP_CRC   0x200   /* strips CRC */
  83 #define RCR_ENABLE      0x100   /* IFF this is set, we can receive packets */
  84 #define RCR_ALMUL       0x4     /* receive all multicast packets */
  85 #define RCR_PROMISC     0x2     /* enable promiscuous mode */
  86 
  87 /* the normal settings for the RCR register : */
  88 #define RCR_NORMAL      (RCR_STRIP_CRC | RCR_ENABLE)
  89 #define RCR_CLEAR       0x0             /* set it to a base state */
  90 
  91 #define COUNTER         6
  92 #define MIR             8
  93 #define MCR             10
  94 /* 12 is reserved */
  95 
  96 /* BANK 1 */
  97 #define CONFIG                  0
  98 #define CFG_AUI_SELECT          0x100
  99 #define BASE                    2
 100 #define ADDR0                   4
 101 #define ADDR1                   6
 102 #define ADDR2                   8
 103 #define GENERAL                 10
 104 #define CONTROL                 12
 105 #define CTL_POWERDOWN           0x2000
 106 #define CTL_LE_ENABLE           0x80
 107 #define CTL_CR_ENABLE           0x40
 108 #define CTL_TE_ENABLE           0x0020
 109 #define CTL_AUTO_RELEASE        0x0800
 110 #define CTL_EPROM_ACCESS        0x0003 /* high if Eprom is being read */
 111 
 112 /* BANK 2 */
 113 #define MMU_CMD         0
 114 #define MC_BUSY         1       /* only readable bit in the register */
 115 #define MC_NOP          0
 116 #define MC_ALLOC        0x20    /* or with number of 256 byte packets */
 117 #define MC_RESET        0x40
 118 #define MC_REMOVE       0x60    /* remove the current rx packet */
 119 #define MC_RELEASE      0x80    /* remove and release the current rx packet */
 120 #define MC_FREEPKT      0xA0    /* Release packet in PNR register */
 121 #define MC_ENQUEUE      0xC0    /* Enqueue the packet for transmit */
 122 
 123 #define PNR_ARR         2
 124 #define FIFO_PORTS      4
 125 
 126 #define FP_RXEMPTY  0x8000
 127 #define FP_TXEMPTY  0x80
 128 
 129 #define POINTER         6
 130 #define PTR_READ        0x2000
 131 #define PTR_RCV         0x8000
 132 #define PTR_AUTOINC     0x4000
 133 #define PTR_AUTO_INC    0x0040
 134 
 135 #define DATA_1          8
 136 #define DATA_2          10
 137 #define INTERRUPT       12
 138 
 139 #define INT_MASK        13
 140 #define IM_RCV_INT      0x1
 141 #define IM_TX_INT       0x2
 142 #define IM_TX_EMPTY_INT 0x4
 143 #define IM_ALLOC_INT    0x8
 144 #define IM_RX_OVRN_INT  0x10
 145 #define IM_EPH_INT      0x20
 146 #define IM_ERCV_INT     0x40 /* not on SMC9192 */
 147 
 148 /* BANK 3 */
 149 #define MULTICAST1      0
 150 #define MULTICAST2      2
 151 #define MULTICAST3      4
 152 #define MULTICAST4      6
 153 #define MGMT            8
 154 #define REVISION        10 /* ( hi: chip id   low: rev # ) */
 155 
 156 
 157 /* this is NOT on SMC9192 */
 158 #define ERCV            12
 159 
 160 #define CHIP_9190       3
 161 #define CHIP_9194       4
 162 #define CHIP_9195       5
 163 #define CHIP_91100      7
 164 
 165 static const char * chip_ids[ 15 ] =  {
 166         NULL, NULL, NULL,
 167         /* 3 */ "SMC91C90/91C92",
 168         /* 4 */ "SMC91C94",
 169         /* 5 */ "SMC91C95",
 170         NULL,
 171         /* 7 */ "SMC91C100",
 172         /* 8 */ "SMC91C100FD",
 173         NULL, NULL, NULL,
 174         NULL, NULL, NULL};
 175 
 176 /*
 177  . Transmit status bits
 178 */
 179 #define TS_SUCCESS 0x0001
 180 #define TS_LOSTCAR 0x0400
 181 #define TS_LATCOL  0x0200
 182 #define TS_16COL   0x0010
 183 
 184 /*
 185  . Receive status bits
 186 */
 187 #define RS_ALGNERR      0x8000
 188 #define RS_BADCRC       0x2000
 189 #define RS_ODDFRAME     0x1000
 190 #define RS_TOOLONG      0x0800
 191 #define RS_TOOSHORT     0x0400
 192 #define RS_MULTICAST    0x0001
 193 #define RS_ERRORS       (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
 194 
 195 static const char * interfaces[ 2 ] = { "TP", "AUI" };
 196 
 197 /*-------------------------------------------------------------------------
 198  .  I define some macros to make it easier to do somewhat common
 199  . or slightly complicated, repeated tasks.
 200  --------------------------------------------------------------------------*/
 201 
 202 /* select a register bank, 0 to 3  */
 203 
 204 #define SMC_SELECT_BANK(x)  { outw( x, ioaddr + BANK_SELECT ); }
 205 
 206 /* define a small delay for the reset */
 207 #define SMC_DELAY() { inw( ioaddr + RCR );\
 208                         inw( ioaddr + RCR );\
 209                         inw( ioaddr + RCR );  }
 210 
 211 /* this enables an interrupt in the interrupt mask register */
 212 #define SMC_ENABLE_INT(x) {\
 213                 unsigned char mask;\
 214                 SMC_SELECT_BANK(2);\
 215                 mask = inb( ioaddr + INT_MASK );\
 216                 mask |= (x);\
 217                 outb( mask, ioaddr + INT_MASK ); \
 218 }
 219 
 220 /* this disables an interrupt from the interrupt mask register */
 221 
 222 #define SMC_DISABLE_INT(x) {\
 223                 unsigned char mask;\
 224                 SMC_SELECT_BANK(2);\
 225                 mask = inb( ioaddr + INT_MASK );\
 226                 mask &= ~(x);\
 227                 outb( mask, ioaddr + INT_MASK ); \
 228 }
 229 
 230 /*----------------------------------------------------------------------
 231  . Define the interrupts that I want to receive from the card
 232  .
 233  . I want:
 234  .  IM_EPH_INT, for nasty errors
 235  .  IM_RCV_INT, for happy received packets
 236  .  IM_RX_OVRN_INT, because I have to kick the receiver
 237  --------------------------------------------------------------------------*/
 238 #define SMC_INTERRUPT_MASK   (IM_EPH_INT | IM_RX_OVRN_INT | IM_RCV_INT)
 239 
 240 #endif  /* _SMC_9194_H_ */
 241 

/* [<][>][^][v][top][bottom][index][help] */