root/drivers/net/ethernet/atheros/atlx/atl1.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. atl1_validate_option
  2. atl1_check_options
  3. atl1_reset_hw
  4. atl1_check_eeprom_exist
  5. atl1_read_eeprom
  6. atl1_read_phy_reg
  7. atl1_spi_read
  8. atl1_get_permanent_address
  9. atl1_read_mac_addr
  10. atl1_hash_mc_addr
  11. atl1_hash_set
  12. atl1_write_phy_reg
  13. atl1_phy_leave_power_saving
  14. atl1_phy_reset
  15. atl1_phy_setup_autoneg_adv
  16. atl1_setup_link
  17. atl1_init_flash_opcode
  18. atl1_init_hw
  19. atl1_get_speed_and_duplex
  20. atl1_set_mac_addr
  21. atl1_sw_init
  22. mdio_read
  23. mdio_write
  24. atl1_mii_ioctl
  25. atl1_setup_ring_resources
  26. atl1_init_ring_ptrs
  27. atl1_clean_rx_ring
  28. atl1_clean_tx_ring
  29. atl1_free_ring_resources
  30. atl1_setup_mac_ctrl
  31. atl1_check_link
  32. set_flow_ctrl_old
  33. set_flow_ctrl_new
  34. atl1_configure
  35. atl1_pcie_patch
  36. atl1_via_workaround
  37. atl1_inc_smb
  38. atl1_update_mailbox
  39. atl1_clean_alloc_flag
  40. atl1_update_rfd_index
  41. atl1_rx_checksum
  42. atl1_alloc_rx_buffers
  43. atl1_intr_rx
  44. atl1_intr_tx
  45. atl1_tpd_avail
  46. atl1_tso
  47. atl1_tx_csum
  48. atl1_tx_map
  49. atl1_tx_queue
  50. atl1_xmit_frame
  51. atl1_rings_clean
  52. atl1_sched_rings_clean
  53. atl1_intr
  54. atl1_phy_config
  55. atl1_reset
  56. atl1_up
  57. atl1_down
  58. atl1_reset_dev_task
  59. atl1_change_mtu
  60. atl1_open
  61. atl1_close
  62. atl1_suspend
  63. atl1_resume
  64. atl1_shutdown
  65. atl1_poll_controller
  66. atl1_probe
  67. atl1_remove
  68. atl1_get_ethtool_stats
  69. atl1_get_sset_count
  70. atl1_get_link_ksettings
  71. atl1_set_link_ksettings
  72. atl1_get_drvinfo
  73. atl1_get_wol
  74. atl1_set_wol
  75. atl1_get_msglevel
  76. atl1_set_msglevel
  77. atl1_get_regs_len
  78. atl1_get_regs
  79. atl1_get_ringparam
  80. atl1_set_ringparam
  81. atl1_get_pauseparam
  82. atl1_set_pauseparam
  83. atl1_get_strings
  84. atl1_nway_reset

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Copyright(c) 2005 - 2006 Attansic Corporation. All rights reserved.
   4  * Copyright(c) 2006 - 2007 Chris Snook <csnook@redhat.com>
   5  * Copyright(c) 2006 - 2008 Jay Cliburn <jcliburn@gmail.com>
   6  *
   7  * Derived from Intel e1000 driver
   8  * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
   9  *
  10  * Contact Information:
  11  * Xiong Huang <xiong.huang@atheros.com>
  12  * Jie Yang <jie.yang@atheros.com>
  13  * Chris Snook <csnook@redhat.com>
  14  * Jay Cliburn <jcliburn@gmail.com>
  15  *
  16  * This version is adapted from the Attansic reference driver.
  17  *
  18  * TODO:
  19  * Add more ethtool functions.
  20  * Fix abstruse irq enable/disable condition described here:
  21  *      http://marc.theaimsgroup.com/?l=linux-netdev&m=116398508500553&w=2
  22  *
  23  * NEEDS TESTING:
  24  * VLAN
  25  * multicast
  26  * promiscuous mode
  27  * interrupt coalescing
  28  * SMP torture testing
  29  */
  30 
  31 #include <linux/atomic.h>
  32 #include <asm/byteorder.h>
  33 
  34 #include <linux/compiler.h>
  35 #include <linux/crc32.h>
  36 #include <linux/delay.h>
  37 #include <linux/dma-mapping.h>
  38 #include <linux/etherdevice.h>
  39 #include <linux/hardirq.h>
  40 #include <linux/if_ether.h>
  41 #include <linux/if_vlan.h>
  42 #include <linux/in.h>
  43 #include <linux/interrupt.h>
  44 #include <linux/ip.h>
  45 #include <linux/irqflags.h>
  46 #include <linux/irqreturn.h>
  47 #include <linux/jiffies.h>
  48 #include <linux/mii.h>
  49 #include <linux/module.h>
  50 #include <linux/net.h>
  51 #include <linux/netdevice.h>
  52 #include <linux/pci.h>
  53 #include <linux/pci_ids.h>
  54 #include <linux/pm.h>
  55 #include <linux/skbuff.h>
  56 #include <linux/slab.h>
  57 #include <linux/spinlock.h>
  58 #include <linux/string.h>
  59 #include <linux/tcp.h>
  60 #include <linux/timer.h>
  61 #include <linux/types.h>
  62 #include <linux/workqueue.h>
  63 
  64 #include <net/checksum.h>
  65 
  66 #include "atl1.h"
  67 
  68 #define ATLX_DRIVER_VERSION "2.1.3"
  69 MODULE_AUTHOR("Xiong Huang <xiong.huang@atheros.com>, "
  70               "Chris Snook <csnook@redhat.com>, "
  71               "Jay Cliburn <jcliburn@gmail.com>");
  72 MODULE_LICENSE("GPL");
  73 MODULE_VERSION(ATLX_DRIVER_VERSION);
  74 
  75 /* Temporary hack for merging atl1 and atl2 */
  76 #include "atlx.c"
  77 
  78 static const struct ethtool_ops atl1_ethtool_ops;
  79 
  80 /*
  81  * This is the only thing that needs to be changed to adjust the
  82  * maximum number of ports that the driver can manage.
  83  */
  84 #define ATL1_MAX_NIC 4
  85 
  86 #define OPTION_UNSET    -1
  87 #define OPTION_DISABLED 0
  88 #define OPTION_ENABLED  1
  89 
  90 #define ATL1_PARAM_INIT { [0 ... ATL1_MAX_NIC] = OPTION_UNSET }
  91 
  92 /*
  93  * Interrupt Moderate Timer in units of 2 us
  94  *
  95  * Valid Range: 10-65535
  96  *
  97  * Default Value: 100 (200us)
  98  */
  99 static int int_mod_timer[ATL1_MAX_NIC+1] = ATL1_PARAM_INIT;
 100 static unsigned int num_int_mod_timer;
 101 module_param_array_named(int_mod_timer, int_mod_timer, int,
 102         &num_int_mod_timer, 0);
 103 MODULE_PARM_DESC(int_mod_timer, "Interrupt moderator timer");
 104 
 105 #define DEFAULT_INT_MOD_CNT     100     /* 200us */
 106 #define MAX_INT_MOD_CNT         65000
 107 #define MIN_INT_MOD_CNT         50
 108 
 109 struct atl1_option {
 110         enum { enable_option, range_option, list_option } type;
 111         char *name;
 112         char *err;
 113         int def;
 114         union {
 115                 struct {        /* range_option info */
 116                         int min;
 117                         int max;
 118                 } r;
 119                 struct {        /* list_option info */
 120                         int nr;
 121                         struct atl1_opt_list {
 122                                 int i;
 123                                 char *str;
 124                         } *p;
 125                 } l;
 126         } arg;
 127 };
 128 
 129 static int atl1_validate_option(int *value, struct atl1_option *opt,
 130                                 struct pci_dev *pdev)
 131 {
 132         if (*value == OPTION_UNSET) {
 133                 *value = opt->def;
 134                 return 0;
 135         }
 136 
 137         switch (opt->type) {
 138         case enable_option:
 139                 switch (*value) {
 140                 case OPTION_ENABLED:
 141                         dev_info(&pdev->dev, "%s enabled\n", opt->name);
 142                         return 0;
 143                 case OPTION_DISABLED:
 144                         dev_info(&pdev->dev, "%s disabled\n", opt->name);
 145                         return 0;
 146                 }
 147                 break;
 148         case range_option:
 149                 if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
 150                         dev_info(&pdev->dev, "%s set to %i\n", opt->name,
 151                                 *value);
 152                         return 0;
 153                 }
 154                 break;
 155         case list_option:{
 156                         int i;
 157                         struct atl1_opt_list *ent;
 158 
 159                         for (i = 0; i < opt->arg.l.nr; i++) {
 160                                 ent = &opt->arg.l.p[i];
 161                                 if (*value == ent->i) {
 162                                         if (ent->str[0] != '\0')
 163                                                 dev_info(&pdev->dev, "%s\n",
 164                                                         ent->str);
 165                                         return 0;
 166                                 }
 167                         }
 168                 }
 169                 break;
 170 
 171         default:
 172                 break;
 173         }
 174 
 175         dev_info(&pdev->dev, "invalid %s specified (%i) %s\n",
 176                 opt->name, *value, opt->err);
 177         *value = opt->def;
 178         return -1;
 179 }
 180 
 181 /**
 182  * atl1_check_options - Range Checking for Command Line Parameters
 183  * @adapter: board private structure
 184  *
 185  * This routine checks all command line parameters for valid user
 186  * input.  If an invalid value is given, or if no user specified
 187  * value exists, a default value is used.  The final value is stored
 188  * in a variable in the adapter structure.
 189  */
 190 static void atl1_check_options(struct atl1_adapter *adapter)
 191 {
 192         struct pci_dev *pdev = adapter->pdev;
 193         int bd = adapter->bd_number;
 194         if (bd >= ATL1_MAX_NIC) {
 195                 dev_notice(&pdev->dev, "no configuration for board#%i\n", bd);
 196                 dev_notice(&pdev->dev, "using defaults for all values\n");
 197         }
 198         {                       /* Interrupt Moderate Timer */
 199                 struct atl1_option opt = {
 200                         .type = range_option,
 201                         .name = "Interrupt Moderator Timer",
 202                         .err = "using default of "
 203                                 __MODULE_STRING(DEFAULT_INT_MOD_CNT),
 204                         .def = DEFAULT_INT_MOD_CNT,
 205                         .arg = {.r = {.min = MIN_INT_MOD_CNT,
 206                                         .max = MAX_INT_MOD_CNT} }
 207                 };
 208                 int val;
 209                 if (num_int_mod_timer > bd) {
 210                         val = int_mod_timer[bd];
 211                         atl1_validate_option(&val, &opt, pdev);
 212                         adapter->imt = (u16) val;
 213                 } else
 214                         adapter->imt = (u16) (opt.def);
 215         }
 216 }
 217 
 218 /*
 219  * atl1_pci_tbl - PCI Device ID Table
 220  */
 221 static const struct pci_device_id atl1_pci_tbl[] = {
 222         {PCI_DEVICE(PCI_VENDOR_ID_ATTANSIC, PCI_DEVICE_ID_ATTANSIC_L1)},
 223         /* required last entry */
 224         {0,}
 225 };
 226 MODULE_DEVICE_TABLE(pci, atl1_pci_tbl);
 227 
 228 static const u32 atl1_default_msg = NETIF_MSG_DRV | NETIF_MSG_PROBE |
 229         NETIF_MSG_LINK | NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP;
 230 
 231 static int debug = -1;
 232 module_param(debug, int, 0);
 233 MODULE_PARM_DESC(debug, "Message level (0=none,...,16=all)");
 234 
 235 /*
 236  * Reset the transmit and receive units; mask and clear all interrupts.
 237  * hw - Struct containing variables accessed by shared code
 238  * return : 0  or  idle status (if error)
 239  */
 240 static s32 atl1_reset_hw(struct atl1_hw *hw)
 241 {
 242         struct pci_dev *pdev = hw->back->pdev;
 243         struct atl1_adapter *adapter = hw->back;
 244         u32 icr;
 245         int i;
 246 
 247         /*
 248          * Clear Interrupt mask to stop board from generating
 249          * interrupts & Clear any pending interrupt events
 250          */
 251         /*
 252          * atlx_irq_disable(adapter);
 253          * iowrite32(0xffffffff, hw->hw_addr + REG_ISR);
 254          */
 255 
 256         /*
 257          * Issue Soft Reset to the MAC.  This will reset the chip's
 258          * transmit, receive, DMA.  It will not effect
 259          * the current PCI configuration.  The global reset bit is self-
 260          * clearing, and should clear within a microsecond.
 261          */
 262         iowrite32(MASTER_CTRL_SOFT_RST, hw->hw_addr + REG_MASTER_CTRL);
 263         ioread32(hw->hw_addr + REG_MASTER_CTRL);
 264 
 265         iowrite16(1, hw->hw_addr + REG_PHY_ENABLE);
 266         ioread16(hw->hw_addr + REG_PHY_ENABLE);
 267 
 268         /* delay about 1ms */
 269         msleep(1);
 270 
 271         /* Wait at least 10ms for All module to be Idle */
 272         for (i = 0; i < 10; i++) {
 273                 icr = ioread32(hw->hw_addr + REG_IDLE_STATUS);
 274                 if (!icr)
 275                         break;
 276                 /* delay 1 ms */
 277                 msleep(1);
 278                 /* FIXME: still the right way to do this? */
 279                 cpu_relax();
 280         }
 281 
 282         if (icr) {
 283                 if (netif_msg_hw(adapter))
 284                         dev_dbg(&pdev->dev, "ICR = 0x%x\n", icr);
 285                 return icr;
 286         }
 287 
 288         return 0;
 289 }
 290 
 291 /* function about EEPROM
 292  *
 293  * check_eeprom_exist
 294  * return 0 if eeprom exist
 295  */
 296 static int atl1_check_eeprom_exist(struct atl1_hw *hw)
 297 {
 298         u32 value;
 299         value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
 300         if (value & SPI_FLASH_CTRL_EN_VPD) {
 301                 value &= ~SPI_FLASH_CTRL_EN_VPD;
 302                 iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
 303         }
 304 
 305         value = ioread16(hw->hw_addr + REG_PCIE_CAP_LIST);
 306         return ((value & 0xFF00) == 0x6C00) ? 0 : 1;
 307 }
 308 
 309 static bool atl1_read_eeprom(struct atl1_hw *hw, u32 offset, u32 *p_value)
 310 {
 311         int i;
 312         u32 control;
 313 
 314         if (offset & 3)
 315                 /* address do not align */
 316                 return false;
 317 
 318         iowrite32(0, hw->hw_addr + REG_VPD_DATA);
 319         control = (offset & VPD_CAP_VPD_ADDR_MASK) << VPD_CAP_VPD_ADDR_SHIFT;
 320         iowrite32(control, hw->hw_addr + REG_VPD_CAP);
 321         ioread32(hw->hw_addr + REG_VPD_CAP);
 322 
 323         for (i = 0; i < 10; i++) {
 324                 msleep(2);
 325                 control = ioread32(hw->hw_addr + REG_VPD_CAP);
 326                 if (control & VPD_CAP_VPD_FLAG)
 327                         break;
 328         }
 329         if (control & VPD_CAP_VPD_FLAG) {
 330                 *p_value = ioread32(hw->hw_addr + REG_VPD_DATA);
 331                 return true;
 332         }
 333         /* timeout */
 334         return false;
 335 }
 336 
 337 /*
 338  * Reads the value from a PHY register
 339  * hw - Struct containing variables accessed by shared code
 340  * reg_addr - address of the PHY register to read
 341  */
 342 static s32 atl1_read_phy_reg(struct atl1_hw *hw, u16 reg_addr, u16 *phy_data)
 343 {
 344         u32 val;
 345         int i;
 346 
 347         val = ((u32) (reg_addr & MDIO_REG_ADDR_MASK)) << MDIO_REG_ADDR_SHIFT |
 348                 MDIO_START | MDIO_SUP_PREAMBLE | MDIO_RW | MDIO_CLK_25_4 <<
 349                 MDIO_CLK_SEL_SHIFT;
 350         iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
 351         ioread32(hw->hw_addr + REG_MDIO_CTRL);
 352 
 353         for (i = 0; i < MDIO_WAIT_TIMES; i++) {
 354                 udelay(2);
 355                 val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
 356                 if (!(val & (MDIO_START | MDIO_BUSY)))
 357                         break;
 358         }
 359         if (!(val & (MDIO_START | MDIO_BUSY))) {
 360                 *phy_data = (u16) val;
 361                 return 0;
 362         }
 363         return ATLX_ERR_PHY;
 364 }
 365 
 366 #define CUSTOM_SPI_CS_SETUP     2
 367 #define CUSTOM_SPI_CLK_HI       2
 368 #define CUSTOM_SPI_CLK_LO       2
 369 #define CUSTOM_SPI_CS_HOLD      2
 370 #define CUSTOM_SPI_CS_HI        3
 371 
 372 static bool atl1_spi_read(struct atl1_hw *hw, u32 addr, u32 *buf)
 373 {
 374         int i;
 375         u32 value;
 376 
 377         iowrite32(0, hw->hw_addr + REG_SPI_DATA);
 378         iowrite32(addr, hw->hw_addr + REG_SPI_ADDR);
 379 
 380         value = SPI_FLASH_CTRL_WAIT_READY |
 381             (CUSTOM_SPI_CS_SETUP & SPI_FLASH_CTRL_CS_SETUP_MASK) <<
 382             SPI_FLASH_CTRL_CS_SETUP_SHIFT | (CUSTOM_SPI_CLK_HI &
 383                                              SPI_FLASH_CTRL_CLK_HI_MASK) <<
 384             SPI_FLASH_CTRL_CLK_HI_SHIFT | (CUSTOM_SPI_CLK_LO &
 385                                            SPI_FLASH_CTRL_CLK_LO_MASK) <<
 386             SPI_FLASH_CTRL_CLK_LO_SHIFT | (CUSTOM_SPI_CS_HOLD &
 387                                            SPI_FLASH_CTRL_CS_HOLD_MASK) <<
 388             SPI_FLASH_CTRL_CS_HOLD_SHIFT | (CUSTOM_SPI_CS_HI &
 389                                             SPI_FLASH_CTRL_CS_HI_MASK) <<
 390             SPI_FLASH_CTRL_CS_HI_SHIFT | (1 & SPI_FLASH_CTRL_INS_MASK) <<
 391             SPI_FLASH_CTRL_INS_SHIFT;
 392 
 393         iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
 394 
 395         value |= SPI_FLASH_CTRL_START;
 396         iowrite32(value, hw->hw_addr + REG_SPI_FLASH_CTRL);
 397         ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
 398 
 399         for (i = 0; i < 10; i++) {
 400                 msleep(1);
 401                 value = ioread32(hw->hw_addr + REG_SPI_FLASH_CTRL);
 402                 if (!(value & SPI_FLASH_CTRL_START))
 403                         break;
 404         }
 405 
 406         if (value & SPI_FLASH_CTRL_START)
 407                 return false;
 408 
 409         *buf = ioread32(hw->hw_addr + REG_SPI_DATA);
 410 
 411         return true;
 412 }
 413 
 414 /*
 415  * get_permanent_address
 416  * return 0 if get valid mac address,
 417  */
 418 static int atl1_get_permanent_address(struct atl1_hw *hw)
 419 {
 420         u32 addr[2];
 421         u32 i, control;
 422         u16 reg;
 423         u8 eth_addr[ETH_ALEN];
 424         bool key_valid;
 425 
 426         if (is_valid_ether_addr(hw->perm_mac_addr))
 427                 return 0;
 428 
 429         /* init */
 430         addr[0] = addr[1] = 0;
 431 
 432         if (!atl1_check_eeprom_exist(hw)) {
 433                 reg = 0;
 434                 key_valid = false;
 435                 /* Read out all EEPROM content */
 436                 i = 0;
 437                 while (1) {
 438                         if (atl1_read_eeprom(hw, i + 0x100, &control)) {
 439                                 if (key_valid) {
 440                                         if (reg == REG_MAC_STA_ADDR)
 441                                                 addr[0] = control;
 442                                         else if (reg == (REG_MAC_STA_ADDR + 4))
 443                                                 addr[1] = control;
 444                                         key_valid = false;
 445                                 } else if ((control & 0xff) == 0x5A) {
 446                                         key_valid = true;
 447                                         reg = (u16) (control >> 16);
 448                                 } else
 449                                         break;
 450                         } else
 451                                 /* read error */
 452                                 break;
 453                         i += 4;
 454                 }
 455 
 456                 *(u32 *) &eth_addr[2] = swab32(addr[0]);
 457                 *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
 458                 if (is_valid_ether_addr(eth_addr)) {
 459                         memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
 460                         return 0;
 461                 }
 462         }
 463 
 464         /* see if SPI FLAGS exist ? */
 465         addr[0] = addr[1] = 0;
 466         reg = 0;
 467         key_valid = false;
 468         i = 0;
 469         while (1) {
 470                 if (atl1_spi_read(hw, i + 0x1f000, &control)) {
 471                         if (key_valid) {
 472                                 if (reg == REG_MAC_STA_ADDR)
 473                                         addr[0] = control;
 474                                 else if (reg == (REG_MAC_STA_ADDR + 4))
 475                                         addr[1] = control;
 476                                 key_valid = false;
 477                         } else if ((control & 0xff) == 0x5A) {
 478                                 key_valid = true;
 479                                 reg = (u16) (control >> 16);
 480                         } else
 481                                 /* data end */
 482                                 break;
 483                 } else
 484                         /* read error */
 485                         break;
 486                 i += 4;
 487         }
 488 
 489         *(u32 *) &eth_addr[2] = swab32(addr[0]);
 490         *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
 491         if (is_valid_ether_addr(eth_addr)) {
 492                 memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
 493                 return 0;
 494         }
 495 
 496         /*
 497          * On some motherboards, the MAC address is written by the
 498          * BIOS directly to the MAC register during POST, and is
 499          * not stored in eeprom.  If all else thus far has failed
 500          * to fetch the permanent MAC address, try reading it directly.
 501          */
 502         addr[0] = ioread32(hw->hw_addr + REG_MAC_STA_ADDR);
 503         addr[1] = ioread16(hw->hw_addr + (REG_MAC_STA_ADDR + 4));
 504         *(u32 *) &eth_addr[2] = swab32(addr[0]);
 505         *(u16 *) &eth_addr[0] = swab16(*(u16 *) &addr[1]);
 506         if (is_valid_ether_addr(eth_addr)) {
 507                 memcpy(hw->perm_mac_addr, eth_addr, ETH_ALEN);
 508                 return 0;
 509         }
 510 
 511         return 1;
 512 }
 513 
 514 /*
 515  * Reads the adapter's MAC address from the EEPROM
 516  * hw - Struct containing variables accessed by shared code
 517  */
 518 static s32 atl1_read_mac_addr(struct atl1_hw *hw)
 519 {
 520         s32 ret = 0;
 521         u16 i;
 522 
 523         if (atl1_get_permanent_address(hw)) {
 524                 eth_random_addr(hw->perm_mac_addr);
 525                 ret = 1;
 526         }
 527 
 528         for (i = 0; i < ETH_ALEN; i++)
 529                 hw->mac_addr[i] = hw->perm_mac_addr[i];
 530         return ret;
 531 }
 532 
 533 /*
 534  * Hashes an address to determine its location in the multicast table
 535  * hw - Struct containing variables accessed by shared code
 536  * mc_addr - the multicast address to hash
 537  *
 538  * atl1_hash_mc_addr
 539  *  purpose
 540  *      set hash value for a multicast address
 541  *      hash calcu processing :
 542  *          1. calcu 32bit CRC for multicast address
 543  *          2. reverse crc with MSB to LSB
 544  */
 545 static u32 atl1_hash_mc_addr(struct atl1_hw *hw, u8 *mc_addr)
 546 {
 547         u32 crc32, value = 0;
 548         int i;
 549 
 550         crc32 = ether_crc_le(6, mc_addr);
 551         for (i = 0; i < 32; i++)
 552                 value |= (((crc32 >> i) & 1) << (31 - i));
 553 
 554         return value;
 555 }
 556 
 557 /*
 558  * Sets the bit in the multicast table corresponding to the hash value.
 559  * hw - Struct containing variables accessed by shared code
 560  * hash_value - Multicast address hash value
 561  */
 562 static void atl1_hash_set(struct atl1_hw *hw, u32 hash_value)
 563 {
 564         u32 hash_bit, hash_reg;
 565         u32 mta;
 566 
 567         /*
 568          * The HASH Table  is a register array of 2 32-bit registers.
 569          * It is treated like an array of 64 bits.  We want to set
 570          * bit BitArray[hash_value]. So we figure out what register
 571          * the bit is in, read it, OR in the new bit, then write
 572          * back the new value.  The register is determined by the
 573          * upper 7 bits of the hash value and the bit within that
 574          * register are determined by the lower 5 bits of the value.
 575          */
 576         hash_reg = (hash_value >> 31) & 0x1;
 577         hash_bit = (hash_value >> 26) & 0x1F;
 578         mta = ioread32((hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
 579         mta |= (1 << hash_bit);
 580         iowrite32(mta, (hw->hw_addr + REG_RX_HASH_TABLE) + (hash_reg << 2));
 581 }
 582 
 583 /*
 584  * Writes a value to a PHY register
 585  * hw - Struct containing variables accessed by shared code
 586  * reg_addr - address of the PHY register to write
 587  * data - data to write to the PHY
 588  */
 589 static s32 atl1_write_phy_reg(struct atl1_hw *hw, u32 reg_addr, u16 phy_data)
 590 {
 591         int i;
 592         u32 val;
 593 
 594         val = ((u32) (phy_data & MDIO_DATA_MASK)) << MDIO_DATA_SHIFT |
 595             (reg_addr & MDIO_REG_ADDR_MASK) << MDIO_REG_ADDR_SHIFT |
 596             MDIO_SUP_PREAMBLE |
 597             MDIO_START | MDIO_CLK_25_4 << MDIO_CLK_SEL_SHIFT;
 598         iowrite32(val, hw->hw_addr + REG_MDIO_CTRL);
 599         ioread32(hw->hw_addr + REG_MDIO_CTRL);
 600 
 601         for (i = 0; i < MDIO_WAIT_TIMES; i++) {
 602                 udelay(2);
 603                 val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
 604                 if (!(val & (MDIO_START | MDIO_BUSY)))
 605                         break;
 606         }
 607 
 608         if (!(val & (MDIO_START | MDIO_BUSY)))
 609                 return 0;
 610 
 611         return ATLX_ERR_PHY;
 612 }
 613 
 614 /*
 615  * Make L001's PHY out of Power Saving State (bug)
 616  * hw - Struct containing variables accessed by shared code
 617  * when power on, L001's PHY always on Power saving State
 618  * (Gigabit Link forbidden)
 619  */
 620 static s32 atl1_phy_leave_power_saving(struct atl1_hw *hw)
 621 {
 622         s32 ret;
 623         ret = atl1_write_phy_reg(hw, 29, 0x0029);
 624         if (ret)
 625                 return ret;
 626         return atl1_write_phy_reg(hw, 30, 0);
 627 }
 628 
 629 /*
 630  * Resets the PHY and make all config validate
 631  * hw - Struct containing variables accessed by shared code
 632  *
 633  * Sets bit 15 and 12 of the MII Control regiser (for F001 bug)
 634  */
 635 static s32 atl1_phy_reset(struct atl1_hw *hw)
 636 {
 637         struct pci_dev *pdev = hw->back->pdev;
 638         struct atl1_adapter *adapter = hw->back;
 639         s32 ret_val;
 640         u16 phy_data;
 641 
 642         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
 643             hw->media_type == MEDIA_TYPE_1000M_FULL)
 644                 phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
 645         else {
 646                 switch (hw->media_type) {
 647                 case MEDIA_TYPE_100M_FULL:
 648                         phy_data =
 649                             MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
 650                             MII_CR_RESET;
 651                         break;
 652                 case MEDIA_TYPE_100M_HALF:
 653                         phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
 654                         break;
 655                 case MEDIA_TYPE_10M_FULL:
 656                         phy_data =
 657                             MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
 658                         break;
 659                 default:
 660                         /* MEDIA_TYPE_10M_HALF: */
 661                         phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
 662                         break;
 663                 }
 664         }
 665 
 666         ret_val = atl1_write_phy_reg(hw, MII_BMCR, phy_data);
 667         if (ret_val) {
 668                 u32 val;
 669                 int i;
 670                 /* pcie serdes link may be down! */
 671                 if (netif_msg_hw(adapter))
 672                         dev_dbg(&pdev->dev, "pcie phy link down\n");
 673 
 674                 for (i = 0; i < 25; i++) {
 675                         msleep(1);
 676                         val = ioread32(hw->hw_addr + REG_MDIO_CTRL);
 677                         if (!(val & (MDIO_START | MDIO_BUSY)))
 678                                 break;
 679                 }
 680 
 681                 if ((val & (MDIO_START | MDIO_BUSY)) != 0) {
 682                         if (netif_msg_hw(adapter))
 683                                 dev_warn(&pdev->dev,
 684                                         "pcie link down at least 25ms\n");
 685                         return ret_val;
 686                 }
 687         }
 688         return 0;
 689 }
 690 
 691 /*
 692  * Configures PHY autoneg and flow control advertisement settings
 693  * hw - Struct containing variables accessed by shared code
 694  */
 695 static s32 atl1_phy_setup_autoneg_adv(struct atl1_hw *hw)
 696 {
 697         s32 ret_val;
 698         s16 mii_autoneg_adv_reg;
 699         s16 mii_1000t_ctrl_reg;
 700 
 701         /* Read the MII Auto-Neg Advertisement Register (Address 4). */
 702         mii_autoneg_adv_reg = MII_AR_DEFAULT_CAP_MASK;
 703 
 704         /* Read the MII 1000Base-T Control Register (Address 9). */
 705         mii_1000t_ctrl_reg = MII_ATLX_CR_1000T_DEFAULT_CAP_MASK;
 706 
 707         /*
 708          * First we clear all the 10/100 mb speed bits in the Auto-Neg
 709          * Advertisement Register (Address 4) and the 1000 mb speed bits in
 710          * the  1000Base-T Control Register (Address 9).
 711          */
 712         mii_autoneg_adv_reg &= ~MII_AR_SPEED_MASK;
 713         mii_1000t_ctrl_reg &= ~MII_ATLX_CR_1000T_SPEED_MASK;
 714 
 715         /*
 716          * Need to parse media_type  and set up
 717          * the appropriate PHY registers.
 718          */
 719         switch (hw->media_type) {
 720         case MEDIA_TYPE_AUTO_SENSOR:
 721                 mii_autoneg_adv_reg |= (MII_AR_10T_HD_CAPS |
 722                                         MII_AR_10T_FD_CAPS |
 723                                         MII_AR_100TX_HD_CAPS |
 724                                         MII_AR_100TX_FD_CAPS);
 725                 mii_1000t_ctrl_reg |= MII_ATLX_CR_1000T_FD_CAPS;
 726                 break;
 727 
 728         case MEDIA_TYPE_1000M_FULL:
 729                 mii_1000t_ctrl_reg |= MII_ATLX_CR_1000T_FD_CAPS;
 730                 break;
 731 
 732         case MEDIA_TYPE_100M_FULL:
 733                 mii_autoneg_adv_reg |= MII_AR_100TX_FD_CAPS;
 734                 break;
 735 
 736         case MEDIA_TYPE_100M_HALF:
 737                 mii_autoneg_adv_reg |= MII_AR_100TX_HD_CAPS;
 738                 break;
 739 
 740         case MEDIA_TYPE_10M_FULL:
 741                 mii_autoneg_adv_reg |= MII_AR_10T_FD_CAPS;
 742                 break;
 743 
 744         default:
 745                 mii_autoneg_adv_reg |= MII_AR_10T_HD_CAPS;
 746                 break;
 747         }
 748 
 749         /* flow control fixed to enable all */
 750         mii_autoneg_adv_reg |= (MII_AR_ASM_DIR | MII_AR_PAUSE);
 751 
 752         hw->mii_autoneg_adv_reg = mii_autoneg_adv_reg;
 753         hw->mii_1000t_ctrl_reg = mii_1000t_ctrl_reg;
 754 
 755         ret_val = atl1_write_phy_reg(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
 756         if (ret_val)
 757                 return ret_val;
 758 
 759         ret_val = atl1_write_phy_reg(hw, MII_ATLX_CR, mii_1000t_ctrl_reg);
 760         if (ret_val)
 761                 return ret_val;
 762 
 763         return 0;
 764 }
 765 
 766 /*
 767  * Configures link settings.
 768  * hw - Struct containing variables accessed by shared code
 769  * Assumes the hardware has previously been reset and the
 770  * transmitter and receiver are not enabled.
 771  */
 772 static s32 atl1_setup_link(struct atl1_hw *hw)
 773 {
 774         struct pci_dev *pdev = hw->back->pdev;
 775         struct atl1_adapter *adapter = hw->back;
 776         s32 ret_val;
 777 
 778         /*
 779          * Options:
 780          *  PHY will advertise value(s) parsed from
 781          *  autoneg_advertised and fc
 782          *  no matter what autoneg is , We will not wait link result.
 783          */
 784         ret_val = atl1_phy_setup_autoneg_adv(hw);
 785         if (ret_val) {
 786                 if (netif_msg_link(adapter))
 787                         dev_dbg(&pdev->dev,
 788                                 "error setting up autonegotiation\n");
 789                 return ret_val;
 790         }
 791         /* SW.Reset , En-Auto-Neg if needed */
 792         ret_val = atl1_phy_reset(hw);
 793         if (ret_val) {
 794                 if (netif_msg_link(adapter))
 795                         dev_dbg(&pdev->dev, "error resetting phy\n");
 796                 return ret_val;
 797         }
 798         hw->phy_configured = true;
 799         return ret_val;
 800 }
 801 
 802 static void atl1_init_flash_opcode(struct atl1_hw *hw)
 803 {
 804         if (hw->flash_vendor >= ARRAY_SIZE(flash_table))
 805                 /* Atmel */
 806                 hw->flash_vendor = 0;
 807 
 808         /* Init OP table */
 809         iowrite8(flash_table[hw->flash_vendor].cmd_program,
 810                 hw->hw_addr + REG_SPI_FLASH_OP_PROGRAM);
 811         iowrite8(flash_table[hw->flash_vendor].cmd_sector_erase,
 812                 hw->hw_addr + REG_SPI_FLASH_OP_SC_ERASE);
 813         iowrite8(flash_table[hw->flash_vendor].cmd_chip_erase,
 814                 hw->hw_addr + REG_SPI_FLASH_OP_CHIP_ERASE);
 815         iowrite8(flash_table[hw->flash_vendor].cmd_rdid,
 816                 hw->hw_addr + REG_SPI_FLASH_OP_RDID);
 817         iowrite8(flash_table[hw->flash_vendor].cmd_wren,
 818                 hw->hw_addr + REG_SPI_FLASH_OP_WREN);
 819         iowrite8(flash_table[hw->flash_vendor].cmd_rdsr,
 820                 hw->hw_addr + REG_SPI_FLASH_OP_RDSR);
 821         iowrite8(flash_table[hw->flash_vendor].cmd_wrsr,
 822                 hw->hw_addr + REG_SPI_FLASH_OP_WRSR);
 823         iowrite8(flash_table[hw->flash_vendor].cmd_read,
 824                 hw->hw_addr + REG_SPI_FLASH_OP_READ);
 825 }
 826 
 827 /*
 828  * Performs basic configuration of the adapter.
 829  * hw - Struct containing variables accessed by shared code
 830  * Assumes that the controller has previously been reset and is in a
 831  * post-reset uninitialized state. Initializes multicast table,
 832  * and  Calls routines to setup link
 833  * Leaves the transmit and receive units disabled and uninitialized.
 834  */
 835 static s32 atl1_init_hw(struct atl1_hw *hw)
 836 {
 837         u32 ret_val = 0;
 838 
 839         /* Zero out the Multicast HASH table */
 840         iowrite32(0, hw->hw_addr + REG_RX_HASH_TABLE);
 841         /* clear the old settings from the multicast hash table */
 842         iowrite32(0, (hw->hw_addr + REG_RX_HASH_TABLE) + (1 << 2));
 843 
 844         atl1_init_flash_opcode(hw);
 845 
 846         if (!hw->phy_configured) {
 847                 /* enable GPHY LinkChange Interrupt */
 848                 ret_val = atl1_write_phy_reg(hw, 18, 0xC00);
 849                 if (ret_val)
 850                         return ret_val;
 851                 /* make PHY out of power-saving state */
 852                 ret_val = atl1_phy_leave_power_saving(hw);
 853                 if (ret_val)
 854                         return ret_val;
 855                 /* Call a subroutine to configure the link */
 856                 ret_val = atl1_setup_link(hw);
 857         }
 858         return ret_val;
 859 }
 860 
 861 /*
 862  * Detects the current speed and duplex settings of the hardware.
 863  * hw - Struct containing variables accessed by shared code
 864  * speed - Speed of the connection
 865  * duplex - Duplex setting of the connection
 866  */
 867 static s32 atl1_get_speed_and_duplex(struct atl1_hw *hw, u16 *speed, u16 *duplex)
 868 {
 869         struct pci_dev *pdev = hw->back->pdev;
 870         struct atl1_adapter *adapter = hw->back;
 871         s32 ret_val;
 872         u16 phy_data;
 873 
 874         /* ; --- Read   PHY Specific Status Register (17) */
 875         ret_val = atl1_read_phy_reg(hw, MII_ATLX_PSSR, &phy_data);
 876         if (ret_val)
 877                 return ret_val;
 878 
 879         if (!(phy_data & MII_ATLX_PSSR_SPD_DPLX_RESOLVED))
 880                 return ATLX_ERR_PHY_RES;
 881 
 882         switch (phy_data & MII_ATLX_PSSR_SPEED) {
 883         case MII_ATLX_PSSR_1000MBS:
 884                 *speed = SPEED_1000;
 885                 break;
 886         case MII_ATLX_PSSR_100MBS:
 887                 *speed = SPEED_100;
 888                 break;
 889         case MII_ATLX_PSSR_10MBS:
 890                 *speed = SPEED_10;
 891                 break;
 892         default:
 893                 if (netif_msg_hw(adapter))
 894                         dev_dbg(&pdev->dev, "error getting speed\n");
 895                 return ATLX_ERR_PHY_SPEED;
 896         }
 897         if (phy_data & MII_ATLX_PSSR_DPLX)
 898                 *duplex = FULL_DUPLEX;
 899         else
 900                 *duplex = HALF_DUPLEX;
 901 
 902         return 0;
 903 }
 904 
 905 static void atl1_set_mac_addr(struct atl1_hw *hw)
 906 {
 907         u32 value;
 908         /*
 909          * 00-0B-6A-F6-00-DC
 910          * 0:  6AF600DC   1: 000B
 911          * low dword
 912          */
 913         value = (((u32) hw->mac_addr[2]) << 24) |
 914             (((u32) hw->mac_addr[3]) << 16) |
 915             (((u32) hw->mac_addr[4]) << 8) | (((u32) hw->mac_addr[5]));
 916         iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR);
 917         /* high dword */
 918         value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1]));
 919         iowrite32(value, (hw->hw_addr + REG_MAC_STA_ADDR) + (1 << 2));
 920 }
 921 
 922 /**
 923  * atl1_sw_init - Initialize general software structures (struct atl1_adapter)
 924  * @adapter: board private structure to initialize
 925  *
 926  * atl1_sw_init initializes the Adapter private data structure.
 927  * Fields are initialized based on PCI device information and
 928  * OS network device settings (MTU size).
 929  */
 930 static int atl1_sw_init(struct atl1_adapter *adapter)
 931 {
 932         struct atl1_hw *hw = &adapter->hw;
 933         struct net_device *netdev = adapter->netdev;
 934 
 935         hw->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
 936         hw->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
 937 
 938         adapter->wol = 0;
 939         device_set_wakeup_enable(&adapter->pdev->dev, false);
 940         adapter->rx_buffer_len = (hw->max_frame_size + 7) & ~7;
 941         adapter->ict = 50000;           /* 100ms */
 942         adapter->link_speed = SPEED_0;  /* hardware init */
 943         adapter->link_duplex = FULL_DUPLEX;
 944 
 945         hw->phy_configured = false;
 946         hw->preamble_len = 7;
 947         hw->ipgt = 0x60;
 948         hw->min_ifg = 0x50;
 949         hw->ipgr1 = 0x40;
 950         hw->ipgr2 = 0x60;
 951         hw->max_retry = 0xf;
 952         hw->lcol = 0x37;
 953         hw->jam_ipg = 7;
 954         hw->rfd_burst = 8;
 955         hw->rrd_burst = 8;
 956         hw->rfd_fetch_gap = 1;
 957         hw->rx_jumbo_th = adapter->rx_buffer_len / 8;
 958         hw->rx_jumbo_lkah = 1;
 959         hw->rrd_ret_timer = 16;
 960         hw->tpd_burst = 4;
 961         hw->tpd_fetch_th = 16;
 962         hw->txf_burst = 0x100;
 963         hw->tx_jumbo_task_th = (hw->max_frame_size + 7) >> 3;
 964         hw->tpd_fetch_gap = 1;
 965         hw->rcb_value = atl1_rcb_64;
 966         hw->dma_ord = atl1_dma_ord_enh;
 967         hw->dmar_block = atl1_dma_req_256;
 968         hw->dmaw_block = atl1_dma_req_256;
 969         hw->cmb_rrd = 4;
 970         hw->cmb_tpd = 4;
 971         hw->cmb_rx_timer = 1;   /* about 2us */
 972         hw->cmb_tx_timer = 1;   /* about 2us */
 973         hw->smb_timer = 100000; /* about 200ms */
 974 
 975         spin_lock_init(&adapter->lock);
 976         spin_lock_init(&adapter->mb_lock);
 977 
 978         return 0;
 979 }
 980 
 981 static int mdio_read(struct net_device *netdev, int phy_id, int reg_num)
 982 {
 983         struct atl1_adapter *adapter = netdev_priv(netdev);
 984         u16 result;
 985 
 986         atl1_read_phy_reg(&adapter->hw, reg_num & 0x1f, &result);
 987 
 988         return result;
 989 }
 990 
 991 static void mdio_write(struct net_device *netdev, int phy_id, int reg_num,
 992         int val)
 993 {
 994         struct atl1_adapter *adapter = netdev_priv(netdev);
 995 
 996         atl1_write_phy_reg(&adapter->hw, reg_num, val);
 997 }
 998 
 999 static int atl1_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
1000 {
1001         struct atl1_adapter *adapter = netdev_priv(netdev);
1002         unsigned long flags;
1003         int retval;
1004 
1005         if (!netif_running(netdev))
1006                 return -EINVAL;
1007 
1008         spin_lock_irqsave(&adapter->lock, flags);
1009         retval = generic_mii_ioctl(&adapter->mii, if_mii(ifr), cmd, NULL);
1010         spin_unlock_irqrestore(&adapter->lock, flags);
1011 
1012         return retval;
1013 }
1014 
1015 /**
1016  * atl1_setup_mem_resources - allocate Tx / RX descriptor resources
1017  * @adapter: board private structure
1018  *
1019  * Return 0 on success, negative on failure
1020  */
1021 static s32 atl1_setup_ring_resources(struct atl1_adapter *adapter)
1022 {
1023         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
1024         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1025         struct atl1_rrd_ring *rrd_ring = &adapter->rrd_ring;
1026         struct atl1_ring_header *ring_header = &adapter->ring_header;
1027         struct pci_dev *pdev = adapter->pdev;
1028         int size;
1029         u8 offset = 0;
1030 
1031         size = sizeof(struct atl1_buffer) * (tpd_ring->count + rfd_ring->count);
1032         tpd_ring->buffer_info = kzalloc(size, GFP_KERNEL);
1033         if (unlikely(!tpd_ring->buffer_info)) {
1034                 if (netif_msg_drv(adapter))
1035                         dev_err(&pdev->dev, "kzalloc failed , size = D%d\n",
1036                                 size);
1037                 goto err_nomem;
1038         }
1039         rfd_ring->buffer_info =
1040                 (tpd_ring->buffer_info + tpd_ring->count);
1041 
1042         /*
1043          * real ring DMA buffer
1044          * each ring/block may need up to 8 bytes for alignment, hence the
1045          * additional 40 bytes tacked onto the end.
1046          */
1047         ring_header->size = size =
1048                 sizeof(struct tx_packet_desc) * tpd_ring->count
1049                 + sizeof(struct rx_free_desc) * rfd_ring->count
1050                 + sizeof(struct rx_return_desc) * rrd_ring->count
1051                 + sizeof(struct coals_msg_block)
1052                 + sizeof(struct stats_msg_block)
1053                 + 40;
1054 
1055         ring_header->desc = pci_alloc_consistent(pdev, ring_header->size,
1056                 &ring_header->dma);
1057         if (unlikely(!ring_header->desc)) {
1058                 if (netif_msg_drv(adapter))
1059                         dev_err(&pdev->dev, "pci_alloc_consistent failed\n");
1060                 goto err_nomem;
1061         }
1062 
1063         /* init TPD ring */
1064         tpd_ring->dma = ring_header->dma;
1065         offset = (tpd_ring->dma & 0x7) ? (8 - (ring_header->dma & 0x7)) : 0;
1066         tpd_ring->dma += offset;
1067         tpd_ring->desc = (u8 *) ring_header->desc + offset;
1068         tpd_ring->size = sizeof(struct tx_packet_desc) * tpd_ring->count;
1069 
1070         /* init RFD ring */
1071         rfd_ring->dma = tpd_ring->dma + tpd_ring->size;
1072         offset = (rfd_ring->dma & 0x7) ? (8 - (rfd_ring->dma & 0x7)) : 0;
1073         rfd_ring->dma += offset;
1074         rfd_ring->desc = (u8 *) tpd_ring->desc + (tpd_ring->size + offset);
1075         rfd_ring->size = sizeof(struct rx_free_desc) * rfd_ring->count;
1076 
1077 
1078         /* init RRD ring */
1079         rrd_ring->dma = rfd_ring->dma + rfd_ring->size;
1080         offset = (rrd_ring->dma & 0x7) ? (8 - (rrd_ring->dma & 0x7)) : 0;
1081         rrd_ring->dma += offset;
1082         rrd_ring->desc = (u8 *) rfd_ring->desc + (rfd_ring->size + offset);
1083         rrd_ring->size = sizeof(struct rx_return_desc) * rrd_ring->count;
1084 
1085 
1086         /* init CMB */
1087         adapter->cmb.dma = rrd_ring->dma + rrd_ring->size;
1088         offset = (adapter->cmb.dma & 0x7) ? (8 - (adapter->cmb.dma & 0x7)) : 0;
1089         adapter->cmb.dma += offset;
1090         adapter->cmb.cmb = (struct coals_msg_block *)
1091                 ((u8 *) rrd_ring->desc + (rrd_ring->size + offset));
1092 
1093         /* init SMB */
1094         adapter->smb.dma = adapter->cmb.dma + sizeof(struct coals_msg_block);
1095         offset = (adapter->smb.dma & 0x7) ? (8 - (adapter->smb.dma & 0x7)) : 0;
1096         adapter->smb.dma += offset;
1097         adapter->smb.smb = (struct stats_msg_block *)
1098                 ((u8 *) adapter->cmb.cmb +
1099                 (sizeof(struct coals_msg_block) + offset));
1100 
1101         return 0;
1102 
1103 err_nomem:
1104         kfree(tpd_ring->buffer_info);
1105         return -ENOMEM;
1106 }
1107 
1108 static void atl1_init_ring_ptrs(struct atl1_adapter *adapter)
1109 {
1110         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
1111         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1112         struct atl1_rrd_ring *rrd_ring = &adapter->rrd_ring;
1113 
1114         atomic_set(&tpd_ring->next_to_use, 0);
1115         atomic_set(&tpd_ring->next_to_clean, 0);
1116 
1117         rfd_ring->next_to_clean = 0;
1118         atomic_set(&rfd_ring->next_to_use, 0);
1119 
1120         rrd_ring->next_to_use = 0;
1121         atomic_set(&rrd_ring->next_to_clean, 0);
1122 }
1123 
1124 /**
1125  * atl1_clean_rx_ring - Free RFD Buffers
1126  * @adapter: board private structure
1127  */
1128 static void atl1_clean_rx_ring(struct atl1_adapter *adapter)
1129 {
1130         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1131         struct atl1_rrd_ring *rrd_ring = &adapter->rrd_ring;
1132         struct atl1_buffer *buffer_info;
1133         struct pci_dev *pdev = adapter->pdev;
1134         unsigned long size;
1135         unsigned int i;
1136 
1137         /* Free all the Rx ring sk_buffs */
1138         for (i = 0; i < rfd_ring->count; i++) {
1139                 buffer_info = &rfd_ring->buffer_info[i];
1140                 if (buffer_info->dma) {
1141                         pci_unmap_page(pdev, buffer_info->dma,
1142                                 buffer_info->length, PCI_DMA_FROMDEVICE);
1143                         buffer_info->dma = 0;
1144                 }
1145                 if (buffer_info->skb) {
1146                         dev_kfree_skb(buffer_info->skb);
1147                         buffer_info->skb = NULL;
1148                 }
1149         }
1150 
1151         size = sizeof(struct atl1_buffer) * rfd_ring->count;
1152         memset(rfd_ring->buffer_info, 0, size);
1153 
1154         /* Zero out the descriptor ring */
1155         memset(rfd_ring->desc, 0, rfd_ring->size);
1156 
1157         rfd_ring->next_to_clean = 0;
1158         atomic_set(&rfd_ring->next_to_use, 0);
1159 
1160         rrd_ring->next_to_use = 0;
1161         atomic_set(&rrd_ring->next_to_clean, 0);
1162 }
1163 
1164 /**
1165  * atl1_clean_tx_ring - Free Tx Buffers
1166  * @adapter: board private structure
1167  */
1168 static void atl1_clean_tx_ring(struct atl1_adapter *adapter)
1169 {
1170         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
1171         struct atl1_buffer *buffer_info;
1172         struct pci_dev *pdev = adapter->pdev;
1173         unsigned long size;
1174         unsigned int i;
1175 
1176         /* Free all the Tx ring sk_buffs */
1177         for (i = 0; i < tpd_ring->count; i++) {
1178                 buffer_info = &tpd_ring->buffer_info[i];
1179                 if (buffer_info->dma) {
1180                         pci_unmap_page(pdev, buffer_info->dma,
1181                                 buffer_info->length, PCI_DMA_TODEVICE);
1182                         buffer_info->dma = 0;
1183                 }
1184         }
1185 
1186         for (i = 0; i < tpd_ring->count; i++) {
1187                 buffer_info = &tpd_ring->buffer_info[i];
1188                 if (buffer_info->skb) {
1189                         dev_kfree_skb_any(buffer_info->skb);
1190                         buffer_info->skb = NULL;
1191                 }
1192         }
1193 
1194         size = sizeof(struct atl1_buffer) * tpd_ring->count;
1195         memset(tpd_ring->buffer_info, 0, size);
1196 
1197         /* Zero out the descriptor ring */
1198         memset(tpd_ring->desc, 0, tpd_ring->size);
1199 
1200         atomic_set(&tpd_ring->next_to_use, 0);
1201         atomic_set(&tpd_ring->next_to_clean, 0);
1202 }
1203 
1204 /**
1205  * atl1_free_ring_resources - Free Tx / RX descriptor Resources
1206  * @adapter: board private structure
1207  *
1208  * Free all transmit software resources
1209  */
1210 static void atl1_free_ring_resources(struct atl1_adapter *adapter)
1211 {
1212         struct pci_dev *pdev = adapter->pdev;
1213         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
1214         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1215         struct atl1_rrd_ring *rrd_ring = &adapter->rrd_ring;
1216         struct atl1_ring_header *ring_header = &adapter->ring_header;
1217 
1218         atl1_clean_tx_ring(adapter);
1219         atl1_clean_rx_ring(adapter);
1220 
1221         kfree(tpd_ring->buffer_info);
1222         pci_free_consistent(pdev, ring_header->size, ring_header->desc,
1223                 ring_header->dma);
1224 
1225         tpd_ring->buffer_info = NULL;
1226         tpd_ring->desc = NULL;
1227         tpd_ring->dma = 0;
1228 
1229         rfd_ring->buffer_info = NULL;
1230         rfd_ring->desc = NULL;
1231         rfd_ring->dma = 0;
1232 
1233         rrd_ring->desc = NULL;
1234         rrd_ring->dma = 0;
1235 
1236         adapter->cmb.dma = 0;
1237         adapter->cmb.cmb = NULL;
1238 
1239         adapter->smb.dma = 0;
1240         adapter->smb.smb = NULL;
1241 }
1242 
1243 static void atl1_setup_mac_ctrl(struct atl1_adapter *adapter)
1244 {
1245         u32 value;
1246         struct atl1_hw *hw = &adapter->hw;
1247         struct net_device *netdev = adapter->netdev;
1248         /* Config MAC CTRL Register */
1249         value = MAC_CTRL_TX_EN | MAC_CTRL_RX_EN;
1250         /* duplex */
1251         if (FULL_DUPLEX == adapter->link_duplex)
1252                 value |= MAC_CTRL_DUPLX;
1253         /* speed */
1254         value |= ((u32) ((SPEED_1000 == adapter->link_speed) ?
1255                          MAC_CTRL_SPEED_1000 : MAC_CTRL_SPEED_10_100) <<
1256                   MAC_CTRL_SPEED_SHIFT);
1257         /* flow control */
1258         value |= (MAC_CTRL_TX_FLOW | MAC_CTRL_RX_FLOW);
1259         /* PAD & CRC */
1260         value |= (MAC_CTRL_ADD_CRC | MAC_CTRL_PAD);
1261         /* preamble length */
1262         value |= (((u32) adapter->hw.preamble_len
1263                    & MAC_CTRL_PRMLEN_MASK) << MAC_CTRL_PRMLEN_SHIFT);
1264         /* vlan */
1265         __atlx_vlan_mode(netdev->features, &value);
1266         /* rx checksum
1267            if (adapter->rx_csum)
1268            value |= MAC_CTRL_RX_CHKSUM_EN;
1269          */
1270         /* filter mode */
1271         value |= MAC_CTRL_BC_EN;
1272         if (netdev->flags & IFF_PROMISC)
1273                 value |= MAC_CTRL_PROMIS_EN;
1274         else if (netdev->flags & IFF_ALLMULTI)
1275                 value |= MAC_CTRL_MC_ALL_EN;
1276         /* value |= MAC_CTRL_LOOPBACK; */
1277         iowrite32(value, hw->hw_addr + REG_MAC_CTRL);
1278 }
1279 
1280 static u32 atl1_check_link(struct atl1_adapter *adapter)
1281 {
1282         struct atl1_hw *hw = &adapter->hw;
1283         struct net_device *netdev = adapter->netdev;
1284         u32 ret_val;
1285         u16 speed, duplex, phy_data;
1286         int reconfig = 0;
1287 
1288         /* MII_BMSR must read twice */
1289         atl1_read_phy_reg(hw, MII_BMSR, &phy_data);
1290         atl1_read_phy_reg(hw, MII_BMSR, &phy_data);
1291         if (!(phy_data & BMSR_LSTATUS)) {
1292                 /* link down */
1293                 if (netif_carrier_ok(netdev)) {
1294                         /* old link state: Up */
1295                         if (netif_msg_link(adapter))
1296                                 dev_info(&adapter->pdev->dev, "link is down\n");
1297                         adapter->link_speed = SPEED_0;
1298                         netif_carrier_off(netdev);
1299                 }
1300                 return 0;
1301         }
1302 
1303         /* Link Up */
1304         ret_val = atl1_get_speed_and_duplex(hw, &speed, &duplex);
1305         if (ret_val)
1306                 return ret_val;
1307 
1308         switch (hw->media_type) {
1309         case MEDIA_TYPE_1000M_FULL:
1310                 if (speed != SPEED_1000 || duplex != FULL_DUPLEX)
1311                         reconfig = 1;
1312                 break;
1313         case MEDIA_TYPE_100M_FULL:
1314                 if (speed != SPEED_100 || duplex != FULL_DUPLEX)
1315                         reconfig = 1;
1316                 break;
1317         case MEDIA_TYPE_100M_HALF:
1318                 if (speed != SPEED_100 || duplex != HALF_DUPLEX)
1319                         reconfig = 1;
1320                 break;
1321         case MEDIA_TYPE_10M_FULL:
1322                 if (speed != SPEED_10 || duplex != FULL_DUPLEX)
1323                         reconfig = 1;
1324                 break;
1325         case MEDIA_TYPE_10M_HALF:
1326                 if (speed != SPEED_10 || duplex != HALF_DUPLEX)
1327                         reconfig = 1;
1328                 break;
1329         }
1330 
1331         /* link result is our setting */
1332         if (!reconfig) {
1333                 if (adapter->link_speed != speed ||
1334                     adapter->link_duplex != duplex) {
1335                         adapter->link_speed = speed;
1336                         adapter->link_duplex = duplex;
1337                         atl1_setup_mac_ctrl(adapter);
1338                         if (netif_msg_link(adapter))
1339                                 dev_info(&adapter->pdev->dev,
1340                                         "%s link is up %d Mbps %s\n",
1341                                         netdev->name, adapter->link_speed,
1342                                         adapter->link_duplex == FULL_DUPLEX ?
1343                                         "full duplex" : "half duplex");
1344                 }
1345                 if (!netif_carrier_ok(netdev)) {
1346                         /* Link down -> Up */
1347                         netif_carrier_on(netdev);
1348                 }
1349                 return 0;
1350         }
1351 
1352         /* change original link status */
1353         if (netif_carrier_ok(netdev)) {
1354                 adapter->link_speed = SPEED_0;
1355                 netif_carrier_off(netdev);
1356                 netif_stop_queue(netdev);
1357         }
1358 
1359         if (hw->media_type != MEDIA_TYPE_AUTO_SENSOR &&
1360             hw->media_type != MEDIA_TYPE_1000M_FULL) {
1361                 switch (hw->media_type) {
1362                 case MEDIA_TYPE_100M_FULL:
1363                         phy_data = MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
1364                                    MII_CR_RESET;
1365                         break;
1366                 case MEDIA_TYPE_100M_HALF:
1367                         phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
1368                         break;
1369                 case MEDIA_TYPE_10M_FULL:
1370                         phy_data =
1371                             MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
1372                         break;
1373                 default:
1374                         /* MEDIA_TYPE_10M_HALF: */
1375                         phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
1376                         break;
1377                 }
1378                 atl1_write_phy_reg(hw, MII_BMCR, phy_data);
1379                 return 0;
1380         }
1381 
1382         /* auto-neg, insert timer to re-config phy */
1383         if (!adapter->phy_timer_pending) {
1384                 adapter->phy_timer_pending = true;
1385                 mod_timer(&adapter->phy_config_timer,
1386                           round_jiffies(jiffies + 3 * HZ));
1387         }
1388 
1389         return 0;
1390 }
1391 
1392 static void set_flow_ctrl_old(struct atl1_adapter *adapter)
1393 {
1394         u32 hi, lo, value;
1395 
1396         /* RFD Flow Control */
1397         value = adapter->rfd_ring.count;
1398         hi = value / 16;
1399         if (hi < 2)
1400                 hi = 2;
1401         lo = value * 7 / 8;
1402 
1403         value = ((hi & RXQ_RXF_PAUSE_TH_HI_MASK) << RXQ_RXF_PAUSE_TH_HI_SHIFT) |
1404                 ((lo & RXQ_RXF_PAUSE_TH_LO_MASK) << RXQ_RXF_PAUSE_TH_LO_SHIFT);
1405         iowrite32(value, adapter->hw.hw_addr + REG_RXQ_RXF_PAUSE_THRESH);
1406 
1407         /* RRD Flow Control */
1408         value = adapter->rrd_ring.count;
1409         lo = value / 16;
1410         hi = value * 7 / 8;
1411         if (lo < 2)
1412                 lo = 2;
1413         value = ((hi & RXQ_RRD_PAUSE_TH_HI_MASK) << RXQ_RRD_PAUSE_TH_HI_SHIFT) |
1414                 ((lo & RXQ_RRD_PAUSE_TH_LO_MASK) << RXQ_RRD_PAUSE_TH_LO_SHIFT);
1415         iowrite32(value, adapter->hw.hw_addr + REG_RXQ_RRD_PAUSE_THRESH);
1416 }
1417 
1418 static void set_flow_ctrl_new(struct atl1_hw *hw)
1419 {
1420         u32 hi, lo, value;
1421 
1422         /* RXF Flow Control */
1423         value = ioread32(hw->hw_addr + REG_SRAM_RXF_LEN);
1424         lo = value / 16;
1425         if (lo < 192)
1426                 lo = 192;
1427         hi = value * 7 / 8;
1428         if (hi < lo)
1429                 hi = lo + 16;
1430         value = ((hi & RXQ_RXF_PAUSE_TH_HI_MASK) << RXQ_RXF_PAUSE_TH_HI_SHIFT) |
1431                 ((lo & RXQ_RXF_PAUSE_TH_LO_MASK) << RXQ_RXF_PAUSE_TH_LO_SHIFT);
1432         iowrite32(value, hw->hw_addr + REG_RXQ_RXF_PAUSE_THRESH);
1433 
1434         /* RRD Flow Control */
1435         value = ioread32(hw->hw_addr + REG_SRAM_RRD_LEN);
1436         lo = value / 8;
1437         hi = value * 7 / 8;
1438         if (lo < 2)
1439                 lo = 2;
1440         if (hi < lo)
1441                 hi = lo + 3;
1442         value = ((hi & RXQ_RRD_PAUSE_TH_HI_MASK) << RXQ_RRD_PAUSE_TH_HI_SHIFT) |
1443                 ((lo & RXQ_RRD_PAUSE_TH_LO_MASK) << RXQ_RRD_PAUSE_TH_LO_SHIFT);
1444         iowrite32(value, hw->hw_addr + REG_RXQ_RRD_PAUSE_THRESH);
1445 }
1446 
1447 /**
1448  * atl1_configure - Configure Transmit&Receive Unit after Reset
1449  * @adapter: board private structure
1450  *
1451  * Configure the Tx /Rx unit of the MAC after a reset.
1452  */
1453 static u32 atl1_configure(struct atl1_adapter *adapter)
1454 {
1455         struct atl1_hw *hw = &adapter->hw;
1456         u32 value;
1457 
1458         /* clear interrupt status */
1459         iowrite32(0xffffffff, adapter->hw.hw_addr + REG_ISR);
1460 
1461         /* set MAC Address */
1462         value = (((u32) hw->mac_addr[2]) << 24) |
1463                 (((u32) hw->mac_addr[3]) << 16) |
1464                 (((u32) hw->mac_addr[4]) << 8) |
1465                 (((u32) hw->mac_addr[5]));
1466         iowrite32(value, hw->hw_addr + REG_MAC_STA_ADDR);
1467         value = (((u32) hw->mac_addr[0]) << 8) | (((u32) hw->mac_addr[1]));
1468         iowrite32(value, hw->hw_addr + (REG_MAC_STA_ADDR + 4));
1469 
1470         /* tx / rx ring */
1471 
1472         /* HI base address */
1473         iowrite32((u32) ((adapter->tpd_ring.dma & 0xffffffff00000000ULL) >> 32),
1474                 hw->hw_addr + REG_DESC_BASE_ADDR_HI);
1475         /* LO base address */
1476         iowrite32((u32) (adapter->rfd_ring.dma & 0x00000000ffffffffULL),
1477                 hw->hw_addr + REG_DESC_RFD_ADDR_LO);
1478         iowrite32((u32) (adapter->rrd_ring.dma & 0x00000000ffffffffULL),
1479                 hw->hw_addr + REG_DESC_RRD_ADDR_LO);
1480         iowrite32((u32) (adapter->tpd_ring.dma & 0x00000000ffffffffULL),
1481                 hw->hw_addr + REG_DESC_TPD_ADDR_LO);
1482         iowrite32((u32) (adapter->cmb.dma & 0x00000000ffffffffULL),
1483                 hw->hw_addr + REG_DESC_CMB_ADDR_LO);
1484         iowrite32((u32) (adapter->smb.dma & 0x00000000ffffffffULL),
1485                 hw->hw_addr + REG_DESC_SMB_ADDR_LO);
1486 
1487         /* element count */
1488         value = adapter->rrd_ring.count;
1489         value <<= 16;
1490         value += adapter->rfd_ring.count;
1491         iowrite32(value, hw->hw_addr + REG_DESC_RFD_RRD_RING_SIZE);
1492         iowrite32(adapter->tpd_ring.count, hw->hw_addr +
1493                 REG_DESC_TPD_RING_SIZE);
1494 
1495         /* Load Ptr */
1496         iowrite32(1, hw->hw_addr + REG_LOAD_PTR);
1497 
1498         /* config Mailbox */
1499         value = ((atomic_read(&adapter->tpd_ring.next_to_use)
1500                   & MB_TPD_PROD_INDX_MASK) << MB_TPD_PROD_INDX_SHIFT) |
1501                 ((atomic_read(&adapter->rrd_ring.next_to_clean)
1502                 & MB_RRD_CONS_INDX_MASK) << MB_RRD_CONS_INDX_SHIFT) |
1503                 ((atomic_read(&adapter->rfd_ring.next_to_use)
1504                 & MB_RFD_PROD_INDX_MASK) << MB_RFD_PROD_INDX_SHIFT);
1505         iowrite32(value, hw->hw_addr + REG_MAILBOX);
1506 
1507         /* config IPG/IFG */
1508         value = (((u32) hw->ipgt & MAC_IPG_IFG_IPGT_MASK)
1509                  << MAC_IPG_IFG_IPGT_SHIFT) |
1510                 (((u32) hw->min_ifg & MAC_IPG_IFG_MIFG_MASK)
1511                 << MAC_IPG_IFG_MIFG_SHIFT) |
1512                 (((u32) hw->ipgr1 & MAC_IPG_IFG_IPGR1_MASK)
1513                 << MAC_IPG_IFG_IPGR1_SHIFT) |
1514                 (((u32) hw->ipgr2 & MAC_IPG_IFG_IPGR2_MASK)
1515                 << MAC_IPG_IFG_IPGR2_SHIFT);
1516         iowrite32(value, hw->hw_addr + REG_MAC_IPG_IFG);
1517 
1518         /* config  Half-Duplex Control */
1519         value = ((u32) hw->lcol & MAC_HALF_DUPLX_CTRL_LCOL_MASK) |
1520                 (((u32) hw->max_retry & MAC_HALF_DUPLX_CTRL_RETRY_MASK)
1521                 << MAC_HALF_DUPLX_CTRL_RETRY_SHIFT) |
1522                 MAC_HALF_DUPLX_CTRL_EXC_DEF_EN |
1523                 (0xa << MAC_HALF_DUPLX_CTRL_ABEBT_SHIFT) |
1524                 (((u32) hw->jam_ipg & MAC_HALF_DUPLX_CTRL_JAMIPG_MASK)
1525                 << MAC_HALF_DUPLX_CTRL_JAMIPG_SHIFT);
1526         iowrite32(value, hw->hw_addr + REG_MAC_HALF_DUPLX_CTRL);
1527 
1528         /* set Interrupt Moderator Timer */
1529         iowrite16(adapter->imt, hw->hw_addr + REG_IRQ_MODU_TIMER_INIT);
1530         iowrite32(MASTER_CTRL_ITIMER_EN, hw->hw_addr + REG_MASTER_CTRL);
1531 
1532         /* set Interrupt Clear Timer */
1533         iowrite16(adapter->ict, hw->hw_addr + REG_CMBDISDMA_TIMER);
1534 
1535         /* set max frame size hw will accept */
1536         iowrite32(hw->max_frame_size, hw->hw_addr + REG_MTU);
1537 
1538         /* jumbo size & rrd retirement timer */
1539         value = (((u32) hw->rx_jumbo_th & RXQ_JMBOSZ_TH_MASK)
1540                  << RXQ_JMBOSZ_TH_SHIFT) |
1541                 (((u32) hw->rx_jumbo_lkah & RXQ_JMBO_LKAH_MASK)
1542                 << RXQ_JMBO_LKAH_SHIFT) |
1543                 (((u32) hw->rrd_ret_timer & RXQ_RRD_TIMER_MASK)
1544                 << RXQ_RRD_TIMER_SHIFT);
1545         iowrite32(value, hw->hw_addr + REG_RXQ_JMBOSZ_RRDTIM);
1546 
1547         /* Flow Control */
1548         switch (hw->dev_rev) {
1549         case 0x8001:
1550         case 0x9001:
1551         case 0x9002:
1552         case 0x9003:
1553                 set_flow_ctrl_old(adapter);
1554                 break;
1555         default:
1556                 set_flow_ctrl_new(hw);
1557                 break;
1558         }
1559 
1560         /* config TXQ */
1561         value = (((u32) hw->tpd_burst & TXQ_CTRL_TPD_BURST_NUM_MASK)
1562                  << TXQ_CTRL_TPD_BURST_NUM_SHIFT) |
1563                 (((u32) hw->txf_burst & TXQ_CTRL_TXF_BURST_NUM_MASK)
1564                 << TXQ_CTRL_TXF_BURST_NUM_SHIFT) |
1565                 (((u32) hw->tpd_fetch_th & TXQ_CTRL_TPD_FETCH_TH_MASK)
1566                 << TXQ_CTRL_TPD_FETCH_TH_SHIFT) | TXQ_CTRL_ENH_MODE |
1567                 TXQ_CTRL_EN;
1568         iowrite32(value, hw->hw_addr + REG_TXQ_CTRL);
1569 
1570         /* min tpd fetch gap & tx jumbo packet size threshold for taskoffload */
1571         value = (((u32) hw->tx_jumbo_task_th & TX_JUMBO_TASK_TH_MASK)
1572                 << TX_JUMBO_TASK_TH_SHIFT) |
1573                 (((u32) hw->tpd_fetch_gap & TX_TPD_MIN_IPG_MASK)
1574                 << TX_TPD_MIN_IPG_SHIFT);
1575         iowrite32(value, hw->hw_addr + REG_TX_JUMBO_TASK_TH_TPD_IPG);
1576 
1577         /* config RXQ */
1578         value = (((u32) hw->rfd_burst & RXQ_CTRL_RFD_BURST_NUM_MASK)
1579                 << RXQ_CTRL_RFD_BURST_NUM_SHIFT) |
1580                 (((u32) hw->rrd_burst & RXQ_CTRL_RRD_BURST_THRESH_MASK)
1581                 << RXQ_CTRL_RRD_BURST_THRESH_SHIFT) |
1582                 (((u32) hw->rfd_fetch_gap & RXQ_CTRL_RFD_PREF_MIN_IPG_MASK)
1583                 << RXQ_CTRL_RFD_PREF_MIN_IPG_SHIFT) | RXQ_CTRL_CUT_THRU_EN |
1584                 RXQ_CTRL_EN;
1585         iowrite32(value, hw->hw_addr + REG_RXQ_CTRL);
1586 
1587         /* config DMA Engine */
1588         value = ((((u32) hw->dmar_block) & DMA_CTRL_DMAR_BURST_LEN_MASK)
1589                 << DMA_CTRL_DMAR_BURST_LEN_SHIFT) |
1590                 ((((u32) hw->dmaw_block) & DMA_CTRL_DMAW_BURST_LEN_MASK)
1591                 << DMA_CTRL_DMAW_BURST_LEN_SHIFT) | DMA_CTRL_DMAR_EN |
1592                 DMA_CTRL_DMAW_EN;
1593         value |= (u32) hw->dma_ord;
1594         if (atl1_rcb_128 == hw->rcb_value)
1595                 value |= DMA_CTRL_RCB_VALUE;
1596         iowrite32(value, hw->hw_addr + REG_DMA_CTRL);
1597 
1598         /* config CMB / SMB */
1599         value = (hw->cmb_tpd > adapter->tpd_ring.count) ?
1600                 hw->cmb_tpd : adapter->tpd_ring.count;
1601         value <<= 16;
1602         value |= hw->cmb_rrd;
1603         iowrite32(value, hw->hw_addr + REG_CMB_WRITE_TH);
1604         value = hw->cmb_rx_timer | ((u32) hw->cmb_tx_timer << 16);
1605         iowrite32(value, hw->hw_addr + REG_CMB_WRITE_TIMER);
1606         iowrite32(hw->smb_timer, hw->hw_addr + REG_SMB_TIMER);
1607 
1608         /* --- enable CMB / SMB */
1609         value = CSMB_CTRL_CMB_EN | CSMB_CTRL_SMB_EN;
1610         iowrite32(value, hw->hw_addr + REG_CSMB_CTRL);
1611 
1612         value = ioread32(adapter->hw.hw_addr + REG_ISR);
1613         if (unlikely((value & ISR_PHY_LINKDOWN) != 0))
1614                 value = 1;      /* config failed */
1615         else
1616                 value = 0;
1617 
1618         /* clear all interrupt status */
1619         iowrite32(0x3fffffff, adapter->hw.hw_addr + REG_ISR);
1620         iowrite32(0, adapter->hw.hw_addr + REG_ISR);
1621         return value;
1622 }
1623 
1624 /*
1625  * atl1_pcie_patch - Patch for PCIE module
1626  */
1627 static void atl1_pcie_patch(struct atl1_adapter *adapter)
1628 {
1629         u32 value;
1630 
1631         /* much vendor magic here */
1632         value = 0x6500;
1633         iowrite32(value, adapter->hw.hw_addr + 0x12FC);
1634         /* pcie flow control mode change */
1635         value = ioread32(adapter->hw.hw_addr + 0x1008);
1636         value |= 0x8000;
1637         iowrite32(value, adapter->hw.hw_addr + 0x1008);
1638 }
1639 
1640 /*
1641  * When ACPI resume on some VIA MotherBoard, the Interrupt Disable bit/0x400
1642  * on PCI Command register is disable.
1643  * The function enable this bit.
1644  * Brackett, 2006/03/15
1645  */
1646 static void atl1_via_workaround(struct atl1_adapter *adapter)
1647 {
1648         unsigned long value;
1649 
1650         value = ioread16(adapter->hw.hw_addr + PCI_COMMAND);
1651         if (value & PCI_COMMAND_INTX_DISABLE)
1652                 value &= ~PCI_COMMAND_INTX_DISABLE;
1653         iowrite32(value, adapter->hw.hw_addr + PCI_COMMAND);
1654 }
1655 
1656 static void atl1_inc_smb(struct atl1_adapter *adapter)
1657 {
1658         struct net_device *netdev = adapter->netdev;
1659         struct stats_msg_block *smb = adapter->smb.smb;
1660 
1661         u64 new_rx_errors = smb->rx_frag +
1662                             smb->rx_fcs_err +
1663                             smb->rx_len_err +
1664                             smb->rx_sz_ov +
1665                             smb->rx_rxf_ov +
1666                             smb->rx_rrd_ov +
1667                             smb->rx_align_err;
1668         u64 new_tx_errors = smb->tx_late_col +
1669                             smb->tx_abort_col +
1670                             smb->tx_underrun +
1671                             smb->tx_trunc;
1672 
1673         /* Fill out the OS statistics structure */
1674         adapter->soft_stats.rx_packets += smb->rx_ok + new_rx_errors;
1675         adapter->soft_stats.tx_packets += smb->tx_ok + new_tx_errors;
1676         adapter->soft_stats.rx_bytes += smb->rx_byte_cnt;
1677         adapter->soft_stats.tx_bytes += smb->tx_byte_cnt;
1678         adapter->soft_stats.multicast += smb->rx_mcast;
1679         adapter->soft_stats.collisions += smb->tx_1_col +
1680                                           smb->tx_2_col +
1681                                           smb->tx_late_col +
1682                                           smb->tx_abort_col;
1683 
1684         /* Rx Errors */
1685         adapter->soft_stats.rx_errors += new_rx_errors;
1686         adapter->soft_stats.rx_fifo_errors += smb->rx_rxf_ov;
1687         adapter->soft_stats.rx_length_errors += smb->rx_len_err;
1688         adapter->soft_stats.rx_crc_errors += smb->rx_fcs_err;
1689         adapter->soft_stats.rx_frame_errors += smb->rx_align_err;
1690 
1691         adapter->soft_stats.rx_pause += smb->rx_pause;
1692         adapter->soft_stats.rx_rrd_ov += smb->rx_rrd_ov;
1693         adapter->soft_stats.rx_trunc += smb->rx_sz_ov;
1694 
1695         /* Tx Errors */
1696         adapter->soft_stats.tx_errors += new_tx_errors;
1697         adapter->soft_stats.tx_fifo_errors += smb->tx_underrun;
1698         adapter->soft_stats.tx_aborted_errors += smb->tx_abort_col;
1699         adapter->soft_stats.tx_window_errors += smb->tx_late_col;
1700 
1701         adapter->soft_stats.excecol += smb->tx_abort_col;
1702         adapter->soft_stats.deffer += smb->tx_defer;
1703         adapter->soft_stats.scc += smb->tx_1_col;
1704         adapter->soft_stats.mcc += smb->tx_2_col;
1705         adapter->soft_stats.latecol += smb->tx_late_col;
1706         adapter->soft_stats.tx_underrun += smb->tx_underrun;
1707         adapter->soft_stats.tx_trunc += smb->tx_trunc;
1708         adapter->soft_stats.tx_pause += smb->tx_pause;
1709 
1710         netdev->stats.rx_bytes = adapter->soft_stats.rx_bytes;
1711         netdev->stats.tx_bytes = adapter->soft_stats.tx_bytes;
1712         netdev->stats.multicast = adapter->soft_stats.multicast;
1713         netdev->stats.collisions = adapter->soft_stats.collisions;
1714         netdev->stats.rx_errors = adapter->soft_stats.rx_errors;
1715         netdev->stats.rx_length_errors =
1716                 adapter->soft_stats.rx_length_errors;
1717         netdev->stats.rx_crc_errors = adapter->soft_stats.rx_crc_errors;
1718         netdev->stats.rx_frame_errors =
1719                 adapter->soft_stats.rx_frame_errors;
1720         netdev->stats.rx_fifo_errors = adapter->soft_stats.rx_fifo_errors;
1721         netdev->stats.rx_dropped = adapter->soft_stats.rx_rrd_ov;
1722         netdev->stats.tx_errors = adapter->soft_stats.tx_errors;
1723         netdev->stats.tx_fifo_errors = adapter->soft_stats.tx_fifo_errors;
1724         netdev->stats.tx_aborted_errors =
1725                 adapter->soft_stats.tx_aborted_errors;
1726         netdev->stats.tx_window_errors =
1727                 adapter->soft_stats.tx_window_errors;
1728         netdev->stats.tx_carrier_errors =
1729                 adapter->soft_stats.tx_carrier_errors;
1730 
1731         netdev->stats.rx_packets = adapter->soft_stats.rx_packets;
1732         netdev->stats.tx_packets = adapter->soft_stats.tx_packets;
1733 }
1734 
1735 static void atl1_update_mailbox(struct atl1_adapter *adapter)
1736 {
1737         unsigned long flags;
1738         u32 tpd_next_to_use;
1739         u32 rfd_next_to_use;
1740         u32 rrd_next_to_clean;
1741         u32 value;
1742 
1743         spin_lock_irqsave(&adapter->mb_lock, flags);
1744 
1745         tpd_next_to_use = atomic_read(&adapter->tpd_ring.next_to_use);
1746         rfd_next_to_use = atomic_read(&adapter->rfd_ring.next_to_use);
1747         rrd_next_to_clean = atomic_read(&adapter->rrd_ring.next_to_clean);
1748 
1749         value = ((rfd_next_to_use & MB_RFD_PROD_INDX_MASK) <<
1750                 MB_RFD_PROD_INDX_SHIFT) |
1751                 ((rrd_next_to_clean & MB_RRD_CONS_INDX_MASK) <<
1752                 MB_RRD_CONS_INDX_SHIFT) |
1753                 ((tpd_next_to_use & MB_TPD_PROD_INDX_MASK) <<
1754                 MB_TPD_PROD_INDX_SHIFT);
1755         iowrite32(value, adapter->hw.hw_addr + REG_MAILBOX);
1756 
1757         spin_unlock_irqrestore(&adapter->mb_lock, flags);
1758 }
1759 
1760 static void atl1_clean_alloc_flag(struct atl1_adapter *adapter,
1761         struct rx_return_desc *rrd, u16 offset)
1762 {
1763         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1764 
1765         while (rfd_ring->next_to_clean != (rrd->buf_indx + offset)) {
1766                 rfd_ring->buffer_info[rfd_ring->next_to_clean].alloced = 0;
1767                 if (++rfd_ring->next_to_clean == rfd_ring->count) {
1768                         rfd_ring->next_to_clean = 0;
1769                 }
1770         }
1771 }
1772 
1773 static void atl1_update_rfd_index(struct atl1_adapter *adapter,
1774         struct rx_return_desc *rrd)
1775 {
1776         u16 num_buf;
1777 
1778         num_buf = (rrd->xsz.xsum_sz.pkt_size + adapter->rx_buffer_len - 1) /
1779                 adapter->rx_buffer_len;
1780         if (rrd->num_buf == num_buf)
1781                 /* clean alloc flag for bad rrd */
1782                 atl1_clean_alloc_flag(adapter, rrd, num_buf);
1783 }
1784 
1785 static void atl1_rx_checksum(struct atl1_adapter *adapter,
1786         struct rx_return_desc *rrd, struct sk_buff *skb)
1787 {
1788         struct pci_dev *pdev = adapter->pdev;
1789 
1790         /*
1791          * The L1 hardware contains a bug that erroneously sets the
1792          * PACKET_FLAG_ERR and ERR_FLAG_L4_CHKSUM bits whenever a
1793          * fragmented IP packet is received, even though the packet
1794          * is perfectly valid and its checksum is correct. There's
1795          * no way to distinguish between one of these good packets
1796          * and a packet that actually contains a TCP/UDP checksum
1797          * error, so all we can do is allow it to be handed up to
1798          * the higher layers and let it be sorted out there.
1799          */
1800 
1801         skb_checksum_none_assert(skb);
1802 
1803         if (unlikely(rrd->pkt_flg & PACKET_FLAG_ERR)) {
1804                 if (rrd->err_flg & (ERR_FLAG_CRC | ERR_FLAG_TRUNC |
1805                                         ERR_FLAG_CODE | ERR_FLAG_OV)) {
1806                         adapter->hw_csum_err++;
1807                         if (netif_msg_rx_err(adapter))
1808                                 dev_printk(KERN_DEBUG, &pdev->dev,
1809                                         "rx checksum error\n");
1810                         return;
1811                 }
1812         }
1813 
1814         /* not IPv4 */
1815         if (!(rrd->pkt_flg & PACKET_FLAG_IPV4))
1816                 /* checksum is invalid, but it's not an IPv4 pkt, so ok */
1817                 return;
1818 
1819         /* IPv4 packet */
1820         if (likely(!(rrd->err_flg &
1821                 (ERR_FLAG_IP_CHKSUM | ERR_FLAG_L4_CHKSUM)))) {
1822                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1823                 adapter->hw_csum_good++;
1824                 return;
1825         }
1826 }
1827 
1828 /**
1829  * atl1_alloc_rx_buffers - Replace used receive buffers
1830  * @adapter: address of board private structure
1831  */
1832 static u16 atl1_alloc_rx_buffers(struct atl1_adapter *adapter)
1833 {
1834         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1835         struct pci_dev *pdev = adapter->pdev;
1836         struct page *page;
1837         unsigned long offset;
1838         struct atl1_buffer *buffer_info, *next_info;
1839         struct sk_buff *skb;
1840         u16 num_alloc = 0;
1841         u16 rfd_next_to_use, next_next;
1842         struct rx_free_desc *rfd_desc;
1843 
1844         next_next = rfd_next_to_use = atomic_read(&rfd_ring->next_to_use);
1845         if (++next_next == rfd_ring->count)
1846                 next_next = 0;
1847         buffer_info = &rfd_ring->buffer_info[rfd_next_to_use];
1848         next_info = &rfd_ring->buffer_info[next_next];
1849 
1850         while (!buffer_info->alloced && !next_info->alloced) {
1851                 if (buffer_info->skb) {
1852                         buffer_info->alloced = 1;
1853                         goto next;
1854                 }
1855 
1856                 rfd_desc = ATL1_RFD_DESC(rfd_ring, rfd_next_to_use);
1857 
1858                 skb = netdev_alloc_skb_ip_align(adapter->netdev,
1859                                                 adapter->rx_buffer_len);
1860                 if (unlikely(!skb)) {
1861                         /* Better luck next round */
1862                         adapter->soft_stats.rx_dropped++;
1863                         break;
1864                 }
1865 
1866                 buffer_info->alloced = 1;
1867                 buffer_info->skb = skb;
1868                 buffer_info->length = (u16) adapter->rx_buffer_len;
1869                 page = virt_to_page(skb->data);
1870                 offset = offset_in_page(skb->data);
1871                 buffer_info->dma = pci_map_page(pdev, page, offset,
1872                                                 adapter->rx_buffer_len,
1873                                                 PCI_DMA_FROMDEVICE);
1874                 rfd_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
1875                 rfd_desc->buf_len = cpu_to_le16(adapter->rx_buffer_len);
1876                 rfd_desc->coalese = 0;
1877 
1878 next:
1879                 rfd_next_to_use = next_next;
1880                 if (unlikely(++next_next == rfd_ring->count))
1881                         next_next = 0;
1882 
1883                 buffer_info = &rfd_ring->buffer_info[rfd_next_to_use];
1884                 next_info = &rfd_ring->buffer_info[next_next];
1885                 num_alloc++;
1886         }
1887 
1888         if (num_alloc) {
1889                 /*
1890                  * Force memory writes to complete before letting h/w
1891                  * know there are new descriptors to fetch.  (Only
1892                  * applicable for weak-ordered memory model archs,
1893                  * such as IA-64).
1894                  */
1895                 wmb();
1896                 atomic_set(&rfd_ring->next_to_use, (int)rfd_next_to_use);
1897         }
1898         return num_alloc;
1899 }
1900 
1901 static int atl1_intr_rx(struct atl1_adapter *adapter, int budget)
1902 {
1903         int i, count;
1904         u16 length;
1905         u16 rrd_next_to_clean;
1906         u32 value;
1907         struct atl1_rfd_ring *rfd_ring = &adapter->rfd_ring;
1908         struct atl1_rrd_ring *rrd_ring = &adapter->rrd_ring;
1909         struct atl1_buffer *buffer_info;
1910         struct rx_return_desc *rrd;
1911         struct sk_buff *skb;
1912 
1913         count = 0;
1914 
1915         rrd_next_to_clean = atomic_read(&rrd_ring->next_to_clean);
1916 
1917         while (count < budget) {
1918                 rrd = ATL1_RRD_DESC(rrd_ring, rrd_next_to_clean);
1919                 i = 1;
1920                 if (likely(rrd->xsz.valid)) {   /* packet valid */
1921 chk_rrd:
1922                         /* check rrd status */
1923                         if (likely(rrd->num_buf == 1))
1924                                 goto rrd_ok;
1925                         else if (netif_msg_rx_err(adapter)) {
1926                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1927                                         "unexpected RRD buffer count\n");
1928                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1929                                         "rx_buf_len = %d\n",
1930                                         adapter->rx_buffer_len);
1931                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1932                                         "RRD num_buf = %d\n",
1933                                         rrd->num_buf);
1934                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1935                                         "RRD pkt_len = %d\n",
1936                                         rrd->xsz.xsum_sz.pkt_size);
1937                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1938                                         "RRD pkt_flg = 0x%08X\n",
1939                                         rrd->pkt_flg);
1940                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1941                                         "RRD err_flg = 0x%08X\n",
1942                                         rrd->err_flg);
1943                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1944                                         "RRD vlan_tag = 0x%08X\n",
1945                                         rrd->vlan_tag);
1946                         }
1947 
1948                         /* rrd seems to be bad */
1949                         if (unlikely(i-- > 0)) {
1950                                 /* rrd may not be DMAed completely */
1951                                 udelay(1);
1952                                 goto chk_rrd;
1953                         }
1954                         /* bad rrd */
1955                         if (netif_msg_rx_err(adapter))
1956                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
1957                                         "bad RRD\n");
1958                         /* see if update RFD index */
1959                         if (rrd->num_buf > 1)
1960                                 atl1_update_rfd_index(adapter, rrd);
1961 
1962                         /* update rrd */
1963                         rrd->xsz.valid = 0;
1964                         if (++rrd_next_to_clean == rrd_ring->count)
1965                                 rrd_next_to_clean = 0;
1966                         count++;
1967                         continue;
1968                 } else {        /* current rrd still not be updated */
1969 
1970                         break;
1971                 }
1972 rrd_ok:
1973                 /* clean alloc flag for bad rrd */
1974                 atl1_clean_alloc_flag(adapter, rrd, 0);
1975 
1976                 buffer_info = &rfd_ring->buffer_info[rrd->buf_indx];
1977                 if (++rfd_ring->next_to_clean == rfd_ring->count)
1978                         rfd_ring->next_to_clean = 0;
1979 
1980                 /* update rrd next to clean */
1981                 if (++rrd_next_to_clean == rrd_ring->count)
1982                         rrd_next_to_clean = 0;
1983                 count++;
1984 
1985                 if (unlikely(rrd->pkt_flg & PACKET_FLAG_ERR)) {
1986                         if (!(rrd->err_flg &
1987                                 (ERR_FLAG_IP_CHKSUM | ERR_FLAG_L4_CHKSUM
1988                                 | ERR_FLAG_LEN))) {
1989                                 /* packet error, don't need upstream */
1990                                 buffer_info->alloced = 0;
1991                                 rrd->xsz.valid = 0;
1992                                 continue;
1993                         }
1994                 }
1995 
1996                 /* Good Receive */
1997                 pci_unmap_page(adapter->pdev, buffer_info->dma,
1998                                buffer_info->length, PCI_DMA_FROMDEVICE);
1999                 buffer_info->dma = 0;
2000                 skb = buffer_info->skb;
2001                 length = le16_to_cpu(rrd->xsz.xsum_sz.pkt_size);
2002 
2003                 skb_put(skb, length - ETH_FCS_LEN);
2004 
2005                 /* Receive Checksum Offload */
2006                 atl1_rx_checksum(adapter, rrd, skb);
2007                 skb->protocol = eth_type_trans(skb, adapter->netdev);
2008 
2009                 if (rrd->pkt_flg & PACKET_FLAG_VLAN_INS) {
2010                         u16 vlan_tag = (rrd->vlan_tag >> 4) |
2011                                         ((rrd->vlan_tag & 7) << 13) |
2012                                         ((rrd->vlan_tag & 8) << 9);
2013 
2014                         __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tag);
2015                 }
2016                 netif_receive_skb(skb);
2017 
2018                 /* let protocol layer free skb */
2019                 buffer_info->skb = NULL;
2020                 buffer_info->alloced = 0;
2021                 rrd->xsz.valid = 0;
2022         }
2023 
2024         atomic_set(&rrd_ring->next_to_clean, rrd_next_to_clean);
2025 
2026         atl1_alloc_rx_buffers(adapter);
2027 
2028         /* update mailbox ? */
2029         if (count) {
2030                 u32 tpd_next_to_use;
2031                 u32 rfd_next_to_use;
2032 
2033                 spin_lock(&adapter->mb_lock);
2034 
2035                 tpd_next_to_use = atomic_read(&adapter->tpd_ring.next_to_use);
2036                 rfd_next_to_use =
2037                     atomic_read(&adapter->rfd_ring.next_to_use);
2038                 rrd_next_to_clean =
2039                     atomic_read(&adapter->rrd_ring.next_to_clean);
2040                 value = ((rfd_next_to_use & MB_RFD_PROD_INDX_MASK) <<
2041                         MB_RFD_PROD_INDX_SHIFT) |
2042                         ((rrd_next_to_clean & MB_RRD_CONS_INDX_MASK) <<
2043                         MB_RRD_CONS_INDX_SHIFT) |
2044                         ((tpd_next_to_use & MB_TPD_PROD_INDX_MASK) <<
2045                         MB_TPD_PROD_INDX_SHIFT);
2046                 iowrite32(value, adapter->hw.hw_addr + REG_MAILBOX);
2047                 spin_unlock(&adapter->mb_lock);
2048         }
2049 
2050         return count;
2051 }
2052 
2053 static int atl1_intr_tx(struct atl1_adapter *adapter)
2054 {
2055         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
2056         struct atl1_buffer *buffer_info;
2057         u16 sw_tpd_next_to_clean;
2058         u16 cmb_tpd_next_to_clean;
2059         int count = 0;
2060 
2061         sw_tpd_next_to_clean = atomic_read(&tpd_ring->next_to_clean);
2062         cmb_tpd_next_to_clean = le16_to_cpu(adapter->cmb.cmb->tpd_cons_idx);
2063 
2064         while (cmb_tpd_next_to_clean != sw_tpd_next_to_clean) {
2065                 buffer_info = &tpd_ring->buffer_info[sw_tpd_next_to_clean];
2066                 if (buffer_info->dma) {
2067                         pci_unmap_page(adapter->pdev, buffer_info->dma,
2068                                        buffer_info->length, PCI_DMA_TODEVICE);
2069                         buffer_info->dma = 0;
2070                 }
2071 
2072                 if (buffer_info->skb) {
2073                         dev_consume_skb_irq(buffer_info->skb);
2074                         buffer_info->skb = NULL;
2075                 }
2076 
2077                 if (++sw_tpd_next_to_clean == tpd_ring->count)
2078                         sw_tpd_next_to_clean = 0;
2079 
2080                 count++;
2081         }
2082         atomic_set(&tpd_ring->next_to_clean, sw_tpd_next_to_clean);
2083 
2084         if (netif_queue_stopped(adapter->netdev) &&
2085             netif_carrier_ok(adapter->netdev))
2086                 netif_wake_queue(adapter->netdev);
2087 
2088         return count;
2089 }
2090 
2091 static u16 atl1_tpd_avail(struct atl1_tpd_ring *tpd_ring)
2092 {
2093         u16 next_to_clean = atomic_read(&tpd_ring->next_to_clean);
2094         u16 next_to_use = atomic_read(&tpd_ring->next_to_use);
2095         return (next_to_clean > next_to_use) ?
2096                 next_to_clean - next_to_use - 1 :
2097                 tpd_ring->count + next_to_clean - next_to_use - 1;
2098 }
2099 
2100 static int atl1_tso(struct atl1_adapter *adapter, struct sk_buff *skb,
2101                     struct tx_packet_desc *ptpd)
2102 {
2103         u8 hdr_len, ip_off;
2104         u32 real_len;
2105 
2106         if (skb_shinfo(skb)->gso_size) {
2107                 int err;
2108 
2109                 err = skb_cow_head(skb, 0);
2110                 if (err < 0)
2111                         return err;
2112 
2113                 if (skb->protocol == htons(ETH_P_IP)) {
2114                         struct iphdr *iph = ip_hdr(skb);
2115 
2116                         real_len = (((unsigned char *)iph - skb->data) +
2117                                 ntohs(iph->tot_len));
2118                         if (real_len < skb->len)
2119                                 pskb_trim(skb, real_len);
2120                         hdr_len = (skb_transport_offset(skb) + tcp_hdrlen(skb));
2121                         if (skb->len == hdr_len) {
2122                                 iph->check = 0;
2123                                 tcp_hdr(skb)->check =
2124                                         ~csum_tcpudp_magic(iph->saddr,
2125                                         iph->daddr, tcp_hdrlen(skb),
2126                                         IPPROTO_TCP, 0);
2127                                 ptpd->word3 |= (iph->ihl & TPD_IPHL_MASK) <<
2128                                         TPD_IPHL_SHIFT;
2129                                 ptpd->word3 |= ((tcp_hdrlen(skb) >> 2) &
2130                                         TPD_TCPHDRLEN_MASK) <<
2131                                         TPD_TCPHDRLEN_SHIFT;
2132                                 ptpd->word3 |= 1 << TPD_IP_CSUM_SHIFT;
2133                                 ptpd->word3 |= 1 << TPD_TCP_CSUM_SHIFT;
2134                                 return 1;
2135                         }
2136 
2137                         iph->check = 0;
2138                         tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
2139                                         iph->daddr, 0, IPPROTO_TCP, 0);
2140                         ip_off = (unsigned char *)iph -
2141                                 (unsigned char *) skb_network_header(skb);
2142                         if (ip_off == 8) /* 802.3-SNAP frame */
2143                                 ptpd->word3 |= 1 << TPD_ETHTYPE_SHIFT;
2144                         else if (ip_off != 0)
2145                                 return -2;
2146 
2147                         ptpd->word3 |= (iph->ihl & TPD_IPHL_MASK) <<
2148                                 TPD_IPHL_SHIFT;
2149                         ptpd->word3 |= ((tcp_hdrlen(skb) >> 2) &
2150                                 TPD_TCPHDRLEN_MASK) << TPD_TCPHDRLEN_SHIFT;
2151                         ptpd->word3 |= (skb_shinfo(skb)->gso_size &
2152                                 TPD_MSS_MASK) << TPD_MSS_SHIFT;
2153                         ptpd->word3 |= 1 << TPD_SEGMENT_EN_SHIFT;
2154                         return 3;
2155                 }
2156         }
2157         return 0;
2158 }
2159 
2160 static int atl1_tx_csum(struct atl1_adapter *adapter, struct sk_buff *skb,
2161         struct tx_packet_desc *ptpd)
2162 {
2163         u8 css, cso;
2164 
2165         if (likely(skb->ip_summed == CHECKSUM_PARTIAL)) {
2166                 css = skb_checksum_start_offset(skb);
2167                 cso = css + (u8) skb->csum_offset;
2168                 if (unlikely(css & 0x1)) {
2169                         /* L1 hardware requires an even number here */
2170                         if (netif_msg_tx_err(adapter))
2171                                 dev_printk(KERN_DEBUG, &adapter->pdev->dev,
2172                                         "payload offset not an even number\n");
2173                         return -1;
2174                 }
2175                 ptpd->word3 |= (css & TPD_PLOADOFFSET_MASK) <<
2176                         TPD_PLOADOFFSET_SHIFT;
2177                 ptpd->word3 |= (cso & TPD_CCSUMOFFSET_MASK) <<
2178                         TPD_CCSUMOFFSET_SHIFT;
2179                 ptpd->word3 |= 1 << TPD_CUST_CSUM_EN_SHIFT;
2180                 return true;
2181         }
2182         return 0;
2183 }
2184 
2185 static void atl1_tx_map(struct atl1_adapter *adapter, struct sk_buff *skb,
2186         struct tx_packet_desc *ptpd)
2187 {
2188         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
2189         struct atl1_buffer *buffer_info;
2190         u16 buf_len = skb->len;
2191         struct page *page;
2192         unsigned long offset;
2193         unsigned int nr_frags;
2194         unsigned int f;
2195         int retval;
2196         u16 next_to_use;
2197         u16 data_len;
2198         u8 hdr_len;
2199 
2200         buf_len -= skb->data_len;
2201         nr_frags = skb_shinfo(skb)->nr_frags;
2202         next_to_use = atomic_read(&tpd_ring->next_to_use);
2203         buffer_info = &tpd_ring->buffer_info[next_to_use];
2204         BUG_ON(buffer_info->skb);
2205         /* put skb in last TPD */
2206         buffer_info->skb = NULL;
2207 
2208         retval = (ptpd->word3 >> TPD_SEGMENT_EN_SHIFT) & TPD_SEGMENT_EN_MASK;
2209         if (retval) {
2210                 /* TSO */
2211                 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
2212                 buffer_info->length = hdr_len;
2213                 page = virt_to_page(skb->data);
2214                 offset = offset_in_page(skb->data);
2215                 buffer_info->dma = pci_map_page(adapter->pdev, page,
2216                                                 offset, hdr_len,
2217                                                 PCI_DMA_TODEVICE);
2218 
2219                 if (++next_to_use == tpd_ring->count)
2220                         next_to_use = 0;
2221 
2222                 if (buf_len > hdr_len) {
2223                         int i, nseg;
2224 
2225                         data_len = buf_len - hdr_len;
2226                         nseg = (data_len + ATL1_MAX_TX_BUF_LEN - 1) /
2227                                 ATL1_MAX_TX_BUF_LEN;
2228                         for (i = 0; i < nseg; i++) {
2229                                 buffer_info =
2230                                     &tpd_ring->buffer_info[next_to_use];
2231                                 buffer_info->skb = NULL;
2232                                 buffer_info->length =
2233                                     (ATL1_MAX_TX_BUF_LEN >=
2234                                      data_len) ? ATL1_MAX_TX_BUF_LEN : data_len;
2235                                 data_len -= buffer_info->length;
2236                                 page = virt_to_page(skb->data +
2237                                         (hdr_len + i * ATL1_MAX_TX_BUF_LEN));
2238                                 offset = offset_in_page(skb->data +
2239                                         (hdr_len + i * ATL1_MAX_TX_BUF_LEN));
2240                                 buffer_info->dma = pci_map_page(adapter->pdev,
2241                                         page, offset, buffer_info->length,
2242                                         PCI_DMA_TODEVICE);
2243                                 if (++next_to_use == tpd_ring->count)
2244                                         next_to_use = 0;
2245                         }
2246                 }
2247         } else {
2248                 /* not TSO */
2249                 buffer_info->length = buf_len;
2250                 page = virt_to_page(skb->data);
2251                 offset = offset_in_page(skb->data);
2252                 buffer_info->dma = pci_map_page(adapter->pdev, page,
2253                         offset, buf_len, PCI_DMA_TODEVICE);
2254                 if (++next_to_use == tpd_ring->count)
2255                         next_to_use = 0;
2256         }
2257 
2258         for (f = 0; f < nr_frags; f++) {
2259                 const skb_frag_t *frag = &skb_shinfo(skb)->frags[f];
2260                 u16 i, nseg;
2261 
2262                 buf_len = skb_frag_size(frag);
2263 
2264                 nseg = (buf_len + ATL1_MAX_TX_BUF_LEN - 1) /
2265                         ATL1_MAX_TX_BUF_LEN;
2266                 for (i = 0; i < nseg; i++) {
2267                         buffer_info = &tpd_ring->buffer_info[next_to_use];
2268                         BUG_ON(buffer_info->skb);
2269 
2270                         buffer_info->skb = NULL;
2271                         buffer_info->length = (buf_len > ATL1_MAX_TX_BUF_LEN) ?
2272                                 ATL1_MAX_TX_BUF_LEN : buf_len;
2273                         buf_len -= buffer_info->length;
2274                         buffer_info->dma = skb_frag_dma_map(&adapter->pdev->dev,
2275                                 frag, i * ATL1_MAX_TX_BUF_LEN,
2276                                 buffer_info->length, DMA_TO_DEVICE);
2277 
2278                         if (++next_to_use == tpd_ring->count)
2279                                 next_to_use = 0;
2280                 }
2281         }
2282 
2283         /* last tpd's buffer-info */
2284         buffer_info->skb = skb;
2285 }
2286 
2287 static void atl1_tx_queue(struct atl1_adapter *adapter, u16 count,
2288        struct tx_packet_desc *ptpd)
2289 {
2290         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
2291         struct atl1_buffer *buffer_info;
2292         struct tx_packet_desc *tpd;
2293         u16 j;
2294         u32 val;
2295         u16 next_to_use = (u16) atomic_read(&tpd_ring->next_to_use);
2296 
2297         for (j = 0; j < count; j++) {
2298                 buffer_info = &tpd_ring->buffer_info[next_to_use];
2299                 tpd = ATL1_TPD_DESC(&adapter->tpd_ring, next_to_use);
2300                 if (tpd != ptpd)
2301                         memcpy(tpd, ptpd, sizeof(struct tx_packet_desc));
2302                 tpd->buffer_addr = cpu_to_le64(buffer_info->dma);
2303                 tpd->word2 &= ~(TPD_BUFLEN_MASK << TPD_BUFLEN_SHIFT);
2304                 tpd->word2 |= (cpu_to_le16(buffer_info->length) &
2305                         TPD_BUFLEN_MASK) << TPD_BUFLEN_SHIFT;
2306 
2307                 /*
2308                  * if this is the first packet in a TSO chain, set
2309                  * TPD_HDRFLAG, otherwise, clear it.
2310                  */
2311                 val = (tpd->word3 >> TPD_SEGMENT_EN_SHIFT) &
2312                         TPD_SEGMENT_EN_MASK;
2313                 if (val) {
2314                         if (!j)
2315                                 tpd->word3 |= 1 << TPD_HDRFLAG_SHIFT;
2316                         else
2317                                 tpd->word3 &= ~(1 << TPD_HDRFLAG_SHIFT);
2318                 }
2319 
2320                 if (j == (count - 1))
2321                         tpd->word3 |= 1 << TPD_EOP_SHIFT;
2322 
2323                 if (++next_to_use == tpd_ring->count)
2324                         next_to_use = 0;
2325         }
2326         /*
2327          * Force memory writes to complete before letting h/w
2328          * know there are new descriptors to fetch.  (Only
2329          * applicable for weak-ordered memory model archs,
2330          * such as IA-64).
2331          */
2332         wmb();
2333 
2334         atomic_set(&tpd_ring->next_to_use, next_to_use);
2335 }
2336 
2337 static netdev_tx_t atl1_xmit_frame(struct sk_buff *skb,
2338                                          struct net_device *netdev)
2339 {
2340         struct atl1_adapter *adapter = netdev_priv(netdev);
2341         struct atl1_tpd_ring *tpd_ring = &adapter->tpd_ring;
2342         int len;
2343         int tso;
2344         int count = 1;
2345         int ret_val;
2346         struct tx_packet_desc *ptpd;
2347         u16 vlan_tag;
2348         unsigned int nr_frags = 0;
2349         unsigned int mss = 0;
2350         unsigned int f;
2351         unsigned int proto_hdr_len;
2352 
2353         len = skb_headlen(skb);
2354 
2355         if (unlikely(skb->len <= 0)) {
2356                 dev_kfree_skb_any(skb);
2357                 return NETDEV_TX_OK;
2358         }
2359 
2360         nr_frags = skb_shinfo(skb)->nr_frags;
2361         for (f = 0; f < nr_frags; f++) {
2362                 unsigned int f_size = skb_frag_size(&skb_shinfo(skb)->frags[f]);
2363                 count += (f_size + ATL1_MAX_TX_BUF_LEN - 1) /
2364                          ATL1_MAX_TX_BUF_LEN;
2365         }
2366 
2367         mss = skb_shinfo(skb)->gso_size;
2368         if (mss) {
2369                 if (skb->protocol == htons(ETH_P_IP)) {
2370                         proto_hdr_len = (skb_transport_offset(skb) +
2371                                          tcp_hdrlen(skb));
2372                         if (unlikely(proto_hdr_len > len)) {
2373                                 dev_kfree_skb_any(skb);
2374                                 return NETDEV_TX_OK;
2375                         }
2376                         /* need additional TPD ? */
2377                         if (proto_hdr_len != len)
2378                                 count += (len - proto_hdr_len +
2379                                         ATL1_MAX_TX_BUF_LEN - 1) /
2380                                         ATL1_MAX_TX_BUF_LEN;
2381                 }
2382         }
2383 
2384         if (atl1_tpd_avail(&adapter->tpd_ring) < count) {
2385                 /* not enough descriptors */
2386                 netif_stop_queue(netdev);
2387                 if (netif_msg_tx_queued(adapter))
2388                         dev_printk(KERN_DEBUG, &adapter->pdev->dev,
2389                                 "tx busy\n");
2390                 return NETDEV_TX_BUSY;
2391         }
2392 
2393         ptpd = ATL1_TPD_DESC(tpd_ring,
2394                 (u16) atomic_read(&tpd_ring->next_to_use));
2395         memset(ptpd, 0, sizeof(struct tx_packet_desc));
2396 
2397         if (skb_vlan_tag_present(skb)) {
2398                 vlan_tag = skb_vlan_tag_get(skb);
2399                 vlan_tag = (vlan_tag << 4) | (vlan_tag >> 13) |
2400                         ((vlan_tag >> 9) & 0x8);
2401                 ptpd->word3 |= 1 << TPD_INS_VL_TAG_SHIFT;
2402                 ptpd->word2 |= (vlan_tag & TPD_VLANTAG_MASK) <<
2403                         TPD_VLANTAG_SHIFT;
2404         }
2405 
2406         tso = atl1_tso(adapter, skb, ptpd);
2407         if (tso < 0) {
2408                 dev_kfree_skb_any(skb);
2409                 return NETDEV_TX_OK;
2410         }
2411 
2412         if (!tso) {
2413                 ret_val = atl1_tx_csum(adapter, skb, ptpd);
2414                 if (ret_val < 0) {
2415                         dev_kfree_skb_any(skb);
2416                         return NETDEV_TX_OK;
2417                 }
2418         }
2419 
2420         atl1_tx_map(adapter, skb, ptpd);
2421         atl1_tx_queue(adapter, count, ptpd);
2422         atl1_update_mailbox(adapter);
2423         return NETDEV_TX_OK;
2424 }
2425 
2426 static int atl1_rings_clean(struct napi_struct *napi, int budget)
2427 {
2428         struct atl1_adapter *adapter = container_of(napi, struct atl1_adapter, napi);
2429         int work_done = atl1_intr_rx(adapter, budget);
2430 
2431         if (atl1_intr_tx(adapter))
2432                 work_done = budget;
2433 
2434         /* Let's come again to process some more packets */
2435         if (work_done >= budget)
2436                 return work_done;
2437 
2438         napi_complete_done(napi, work_done);
2439         /* re-enable Interrupt */
2440         if (likely(adapter->int_enabled))
2441                 atlx_imr_set(adapter, IMR_NORMAL_MASK);
2442         return work_done;
2443 }
2444 
2445 static inline int atl1_sched_rings_clean(struct atl1_adapter* adapter)
2446 {
2447         if (!napi_schedule_prep(&adapter->napi))
2448                 /* It is possible in case even the RX/TX ints are disabled via IMR
2449                  * register the ISR bits are set anyway (but do not produce IRQ).
2450                  * To handle such situation the napi functions used to check is
2451                  * something scheduled or not.
2452                  */
2453                 return 0;
2454 
2455         __napi_schedule(&adapter->napi);
2456 
2457         /*
2458          * Disable RX/TX ints via IMR register if it is
2459          * allowed. NAPI handler must reenable them in same
2460          * way.
2461          */
2462         if (!adapter->int_enabled)
2463                 return 1;
2464 
2465         atlx_imr_set(adapter, IMR_NORXTX_MASK);
2466         return 1;
2467 }
2468 
2469 /**
2470  * atl1_intr - Interrupt Handler
2471  * @irq: interrupt number
2472  * @data: pointer to a network interface device structure
2473  */
2474 static irqreturn_t atl1_intr(int irq, void *data)
2475 {
2476         struct atl1_adapter *adapter = netdev_priv(data);
2477         u32 status;
2478 
2479         status = adapter->cmb.cmb->int_stats;
2480         if (!status)
2481                 return IRQ_NONE;
2482 
2483         /* clear CMB interrupt status at once,
2484          * but leave rx/tx interrupt status in case it should be dropped
2485          * only if rx/tx processing queued. In other case interrupt
2486          * can be lost.
2487          */
2488         adapter->cmb.cmb->int_stats = status & (ISR_CMB_TX | ISR_CMB_RX);
2489 
2490         if (status & ISR_GPHY)  /* clear phy status */
2491                 atlx_clear_phy_int(adapter);
2492 
2493         /* clear ISR status, and Enable CMB DMA/Disable Interrupt */
2494         iowrite32(status | ISR_DIS_INT, adapter->hw.hw_addr + REG_ISR);
2495 
2496         /* check if SMB intr */
2497         if (status & ISR_SMB)
2498                 atl1_inc_smb(adapter);
2499 
2500         /* check if PCIE PHY Link down */
2501         if (status & ISR_PHY_LINKDOWN) {
2502                 if (netif_msg_intr(adapter))
2503                         dev_printk(KERN_DEBUG, &adapter->pdev->dev,
2504                                 "pcie phy link down %x\n", status);
2505                 if (netif_running(adapter->netdev)) {   /* reset MAC */
2506                         atlx_irq_disable(adapter);
2507                         schedule_work(&adapter->reset_dev_task);
2508                         return IRQ_HANDLED;
2509                 }
2510         }
2511 
2512         /* check if DMA read/write error ? */
2513         if (status & (ISR_DMAR_TO_RST | ISR_DMAW_TO_RST)) {
2514                 if (netif_msg_intr(adapter))
2515                         dev_printk(KERN_DEBUG, &adapter->pdev->dev,
2516                                 "pcie DMA r/w error (status = 0x%x)\n",
2517                                 status);
2518                 atlx_irq_disable(adapter);
2519                 schedule_work(&adapter->reset_dev_task);
2520                 return IRQ_HANDLED;
2521         }
2522 
2523         /* link event */
2524         if (status & ISR_GPHY) {
2525                 adapter->soft_stats.tx_carrier_errors++;
2526                 atl1_check_for_link(adapter);
2527         }
2528 
2529         /* transmit or receive event */
2530         if (status & (ISR_CMB_TX | ISR_CMB_RX) &&
2531             atl1_sched_rings_clean(adapter))
2532                 adapter->cmb.cmb->int_stats = adapter->cmb.cmb->int_stats &
2533                                               ~(ISR_CMB_TX | ISR_CMB_RX);
2534 
2535         /* rx exception */
2536         if (unlikely(status & (ISR_RXF_OV | ISR_RFD_UNRUN |
2537                 ISR_RRD_OV | ISR_HOST_RFD_UNRUN |
2538                 ISR_HOST_RRD_OV))) {
2539                 if (netif_msg_intr(adapter))
2540                         dev_printk(KERN_DEBUG,
2541                                 &adapter->pdev->dev,
2542                                 "rx exception, ISR = 0x%x\n",
2543                                 status);
2544                 atl1_sched_rings_clean(adapter);
2545         }
2546 
2547         /* re-enable Interrupt */
2548         iowrite32(ISR_DIS_SMB | ISR_DIS_DMA, adapter->hw.hw_addr + REG_ISR);
2549         return IRQ_HANDLED;
2550 }
2551 
2552 
2553 /**
2554  * atl1_phy_config - Timer Call-back
2555  * @data: pointer to netdev cast into an unsigned long
2556  */
2557 static void atl1_phy_config(struct timer_list *t)
2558 {
2559         struct atl1_adapter *adapter = from_timer(adapter, t,
2560                                                   phy_config_timer);
2561         struct atl1_hw *hw = &adapter->hw;
2562         unsigned long flags;
2563 
2564         spin_lock_irqsave(&adapter->lock, flags);
2565         adapter->phy_timer_pending = false;
2566         atl1_write_phy_reg(hw, MII_ADVERTISE, hw->mii_autoneg_adv_reg);
2567         atl1_write_phy_reg(hw, MII_ATLX_CR, hw->mii_1000t_ctrl_reg);
2568         atl1_write_phy_reg(hw, MII_BMCR, MII_CR_RESET | MII_CR_AUTO_NEG_EN);
2569         spin_unlock_irqrestore(&adapter->lock, flags);
2570 }
2571 
2572 /*
2573  * Orphaned vendor comment left intact here:
2574  * <vendor comment>
2575  * If TPD Buffer size equal to 0, PCIE DMAR_TO_INT
2576  * will assert. We do soft reset <0x1400=1> according
2577  * with the SPEC. BUT, it seemes that PCIE or DMA
2578  * state-machine will not be reset. DMAR_TO_INT will
2579  * assert again and again.
2580  * </vendor comment>
2581  */
2582 
2583 static int atl1_reset(struct atl1_adapter *adapter)
2584 {
2585         int ret;
2586         ret = atl1_reset_hw(&adapter->hw);
2587         if (ret)
2588                 return ret;
2589         return atl1_init_hw(&adapter->hw);
2590 }
2591 
2592 static s32 atl1_up(struct atl1_adapter *adapter)
2593 {
2594         struct net_device *netdev = adapter->netdev;
2595         int err;
2596         int irq_flags = 0;
2597 
2598         /* hardware has been reset, we need to reload some things */
2599         atlx_set_multi(netdev);
2600         atl1_init_ring_ptrs(adapter);
2601         atlx_restore_vlan(adapter);
2602         err = atl1_alloc_rx_buffers(adapter);
2603         if (unlikely(!err))
2604                 /* no RX BUFFER allocated */
2605                 return -ENOMEM;
2606 
2607         if (unlikely(atl1_configure(adapter))) {
2608                 err = -EIO;
2609                 goto err_up;
2610         }
2611 
2612         err = pci_enable_msi(adapter->pdev);
2613         if (err) {
2614                 if (netif_msg_ifup(adapter))
2615                         dev_info(&adapter->pdev->dev,
2616                                 "Unable to enable MSI: %d\n", err);
2617                 irq_flags |= IRQF_SHARED;
2618         }
2619 
2620         err = request_irq(adapter->pdev->irq, atl1_intr, irq_flags,
2621                         netdev->name, netdev);
2622         if (unlikely(err))
2623                 goto err_up;
2624 
2625         napi_enable(&adapter->napi);
2626         atlx_irq_enable(adapter);
2627         atl1_check_link(adapter);
2628         netif_start_queue(netdev);
2629         return 0;
2630 
2631 err_up:
2632         pci_disable_msi(adapter->pdev);
2633         /* free rx_buffers */
2634         atl1_clean_rx_ring(adapter);
2635         return err;
2636 }
2637 
2638 static void atl1_down(struct atl1_adapter *adapter)
2639 {
2640         struct net_device *netdev = adapter->netdev;
2641 
2642         napi_disable(&adapter->napi);
2643         netif_stop_queue(netdev);
2644         del_timer_sync(&adapter->phy_config_timer);
2645         adapter->phy_timer_pending = false;
2646 
2647         atlx_irq_disable(adapter);
2648         free_irq(adapter->pdev->irq, netdev);
2649         pci_disable_msi(adapter->pdev);
2650         atl1_reset_hw(&adapter->hw);
2651         adapter->cmb.cmb->int_stats = 0;
2652 
2653         adapter->link_speed = SPEED_0;
2654         adapter->link_duplex = -1;
2655         netif_carrier_off(netdev);
2656 
2657         atl1_clean_tx_ring(adapter);
2658         atl1_clean_rx_ring(adapter);
2659 }
2660 
2661 static void atl1_reset_dev_task(struct work_struct *work)
2662 {
2663         struct atl1_adapter *adapter =
2664                 container_of(work, struct atl1_adapter, reset_dev_task);
2665         struct net_device *netdev = adapter->netdev;
2666 
2667         netif_device_detach(netdev);
2668         atl1_down(adapter);
2669         atl1_up(adapter);
2670         netif_device_attach(netdev);
2671 }
2672 
2673 /**
2674  * atl1_change_mtu - Change the Maximum Transfer Unit
2675  * @netdev: network interface device structure
2676  * @new_mtu: new value for maximum frame size
2677  *
2678  * Returns 0 on success, negative on failure
2679  */
2680 static int atl1_change_mtu(struct net_device *netdev, int new_mtu)
2681 {
2682         struct atl1_adapter *adapter = netdev_priv(netdev);
2683         int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN;
2684 
2685         adapter->hw.max_frame_size = max_frame;
2686         adapter->hw.tx_jumbo_task_th = (max_frame + 7) >> 3;
2687         adapter->rx_buffer_len = (max_frame + 7) & ~7;
2688         adapter->hw.rx_jumbo_th = adapter->rx_buffer_len / 8;
2689 
2690         netdev->mtu = new_mtu;
2691         if (netif_running(netdev)) {
2692                 atl1_down(adapter);
2693                 atl1_up(adapter);
2694         }
2695 
2696         return 0;
2697 }
2698 
2699 /**
2700  * atl1_open - Called when a network interface is made active
2701  * @netdev: network interface device structure
2702  *
2703  * Returns 0 on success, negative value on failure
2704  *
2705  * The open entry point is called when a network interface is made
2706  * active by the system (IFF_UP).  At this point all resources needed
2707  * for transmit and receive operations are allocated, the interrupt
2708  * handler is registered with the OS, the watchdog timer is started,
2709  * and the stack is notified that the interface is ready.
2710  */
2711 static int atl1_open(struct net_device *netdev)
2712 {
2713         struct atl1_adapter *adapter = netdev_priv(netdev);
2714         int err;
2715 
2716         netif_carrier_off(netdev);
2717 
2718         /* allocate transmit descriptors */
2719         err = atl1_setup_ring_resources(adapter);
2720         if (err)
2721                 return err;
2722 
2723         err = atl1_up(adapter);
2724         if (err)
2725                 goto err_up;
2726 
2727         return 0;
2728 
2729 err_up:
2730         atl1_reset(adapter);
2731         return err;
2732 }
2733 
2734 /**
2735  * atl1_close - Disables a network interface
2736  * @netdev: network interface device structure
2737  *
2738  * Returns 0, this is not allowed to fail
2739  *
2740  * The close entry point is called when an interface is de-activated
2741  * by the OS.  The hardware is still under the drivers control, but
2742  * needs to be disabled.  A global MAC reset is issued to stop the
2743  * hardware, and all transmit and receive resources are freed.
2744  */
2745 static int atl1_close(struct net_device *netdev)
2746 {
2747         struct atl1_adapter *adapter = netdev_priv(netdev);
2748         atl1_down(adapter);
2749         atl1_free_ring_resources(adapter);
2750         return 0;
2751 }
2752 
2753 #ifdef CONFIG_PM_SLEEP
2754 static int atl1_suspend(struct device *dev)
2755 {
2756         struct net_device *netdev = dev_get_drvdata(dev);
2757         struct atl1_adapter *adapter = netdev_priv(netdev);
2758         struct atl1_hw *hw = &adapter->hw;
2759         u32 ctrl = 0;
2760         u32 wufc = adapter->wol;
2761         u32 val;
2762         u16 speed;
2763         u16 duplex;
2764 
2765         netif_device_detach(netdev);
2766         if (netif_running(netdev))
2767                 atl1_down(adapter);
2768 
2769         atl1_read_phy_reg(hw, MII_BMSR, (u16 *) & ctrl);
2770         atl1_read_phy_reg(hw, MII_BMSR, (u16 *) & ctrl);
2771         val = ctrl & BMSR_LSTATUS;
2772         if (val)
2773                 wufc &= ~ATLX_WUFC_LNKC;
2774         if (!wufc)
2775                 goto disable_wol;
2776 
2777         if (val) {
2778                 val = atl1_get_speed_and_duplex(hw, &speed, &duplex);
2779                 if (val) {
2780                         if (netif_msg_ifdown(adapter))
2781                                 dev_printk(KERN_DEBUG, dev,
2782                                         "error getting speed/duplex\n");
2783                         goto disable_wol;
2784                 }
2785 
2786                 ctrl = 0;
2787 
2788                 /* enable magic packet WOL */
2789                 if (wufc & ATLX_WUFC_MAG)
2790                         ctrl |= (WOL_MAGIC_EN | WOL_MAGIC_PME_EN);
2791                 iowrite32(ctrl, hw->hw_addr + REG_WOL_CTRL);
2792                 ioread32(hw->hw_addr + REG_WOL_CTRL);
2793 
2794                 /* configure the mac */
2795                 ctrl = MAC_CTRL_RX_EN;
2796                 ctrl |= ((u32)((speed == SPEED_1000) ? MAC_CTRL_SPEED_1000 :
2797                         MAC_CTRL_SPEED_10_100) << MAC_CTRL_SPEED_SHIFT);
2798                 if (duplex == FULL_DUPLEX)
2799                         ctrl |= MAC_CTRL_DUPLX;
2800                 ctrl |= (((u32)adapter->hw.preamble_len &
2801                         MAC_CTRL_PRMLEN_MASK) << MAC_CTRL_PRMLEN_SHIFT);
2802                 __atlx_vlan_mode(netdev->features, &ctrl);
2803                 if (wufc & ATLX_WUFC_MAG)
2804                         ctrl |= MAC_CTRL_BC_EN;
2805                 iowrite32(ctrl, hw->hw_addr + REG_MAC_CTRL);
2806                 ioread32(hw->hw_addr + REG_MAC_CTRL);
2807 
2808                 /* poke the PHY */
2809                 ctrl = ioread32(hw->hw_addr + REG_PCIE_PHYMISC);
2810                 ctrl |= PCIE_PHYMISC_FORCE_RCV_DET;
2811                 iowrite32(ctrl, hw->hw_addr + REG_PCIE_PHYMISC);
2812                 ioread32(hw->hw_addr + REG_PCIE_PHYMISC);
2813         } else {
2814                 ctrl |= (WOL_LINK_CHG_EN | WOL_LINK_CHG_PME_EN);
2815                 iowrite32(ctrl, hw->hw_addr + REG_WOL_CTRL);
2816                 ioread32(hw->hw_addr + REG_WOL_CTRL);
2817                 iowrite32(0, hw->hw_addr + REG_MAC_CTRL);
2818                 ioread32(hw->hw_addr + REG_MAC_CTRL);
2819                 hw->phy_configured = false;
2820         }
2821 
2822         return 0;
2823 
2824  disable_wol:
2825         iowrite32(0, hw->hw_addr + REG_WOL_CTRL);
2826         ioread32(hw->hw_addr + REG_WOL_CTRL);
2827         ctrl = ioread32(hw->hw_addr + REG_PCIE_PHYMISC);
2828         ctrl |= PCIE_PHYMISC_FORCE_RCV_DET;
2829         iowrite32(ctrl, hw->hw_addr + REG_PCIE_PHYMISC);
2830         ioread32(hw->hw_addr + REG_PCIE_PHYMISC);
2831         hw->phy_configured = false;
2832 
2833         return 0;
2834 }
2835 
2836 static int atl1_resume(struct device *dev)
2837 {
2838         struct net_device *netdev = dev_get_drvdata(dev);
2839         struct atl1_adapter *adapter = netdev_priv(netdev);
2840 
2841         iowrite32(0, adapter->hw.hw_addr + REG_WOL_CTRL);
2842 
2843         atl1_reset_hw(&adapter->hw);
2844 
2845         if (netif_running(netdev)) {
2846                 adapter->cmb.cmb->int_stats = 0;
2847                 atl1_up(adapter);
2848         }
2849         netif_device_attach(netdev);
2850 
2851         return 0;
2852 }
2853 #endif
2854 
2855 static SIMPLE_DEV_PM_OPS(atl1_pm_ops, atl1_suspend, atl1_resume);
2856 
2857 static void atl1_shutdown(struct pci_dev *pdev)
2858 {
2859         struct net_device *netdev = pci_get_drvdata(pdev);
2860         struct atl1_adapter *adapter = netdev_priv(netdev);
2861 
2862 #ifdef CONFIG_PM_SLEEP
2863         atl1_suspend(&pdev->dev);
2864 #endif
2865         pci_wake_from_d3(pdev, adapter->wol);
2866         pci_set_power_state(pdev, PCI_D3hot);
2867 }
2868 
2869 #ifdef CONFIG_NET_POLL_CONTROLLER
2870 static void atl1_poll_controller(struct net_device *netdev)
2871 {
2872         disable_irq(netdev->irq);
2873         atl1_intr(netdev->irq, netdev);
2874         enable_irq(netdev->irq);
2875 }
2876 #endif
2877 
2878 static const struct net_device_ops atl1_netdev_ops = {
2879         .ndo_open               = atl1_open,
2880         .ndo_stop               = atl1_close,
2881         .ndo_start_xmit         = atl1_xmit_frame,
2882         .ndo_set_rx_mode        = atlx_set_multi,
2883         .ndo_validate_addr      = eth_validate_addr,
2884         .ndo_set_mac_address    = atl1_set_mac,
2885         .ndo_change_mtu         = atl1_change_mtu,
2886         .ndo_fix_features       = atlx_fix_features,
2887         .ndo_set_features       = atlx_set_features,
2888         .ndo_do_ioctl           = atlx_ioctl,
2889         .ndo_tx_timeout         = atlx_tx_timeout,
2890 #ifdef CONFIG_NET_POLL_CONTROLLER
2891         .ndo_poll_controller    = atl1_poll_controller,
2892 #endif
2893 };
2894 
2895 /**
2896  * atl1_probe - Device Initialization Routine
2897  * @pdev: PCI device information struct
2898  * @ent: entry in atl1_pci_tbl
2899  *
2900  * Returns 0 on success, negative on failure
2901  *
2902  * atl1_probe initializes an adapter identified by a pci_dev structure.
2903  * The OS initialization, configuring of the adapter private structure,
2904  * and a hardware reset occur.
2905  */
2906 static int atl1_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
2907 {
2908         struct net_device *netdev;
2909         struct atl1_adapter *adapter;
2910         static int cards_found = 0;
2911         int err;
2912 
2913         err = pci_enable_device(pdev);
2914         if (err)
2915                 return err;
2916 
2917         /*
2918          * The atl1 chip can DMA to 64-bit addresses, but it uses a single
2919          * shared register for the high 32 bits, so only a single, aligned,
2920          * 4 GB physical address range can be used at a time.
2921          *
2922          * Supporting 64-bit DMA on this hardware is more trouble than it's
2923          * worth.  It is far easier to limit to 32-bit DMA than update
2924          * various kernel subsystems to support the mechanics required by a
2925          * fixed-high-32-bit system.
2926          */
2927         err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
2928         if (err) {
2929                 dev_err(&pdev->dev, "no usable DMA configuration\n");
2930                 goto err_dma;
2931         }
2932         /*
2933          * Mark all PCI regions associated with PCI device
2934          * pdev as being reserved by owner atl1_driver_name
2935          */
2936         err = pci_request_regions(pdev, ATLX_DRIVER_NAME);
2937         if (err)
2938                 goto err_request_regions;
2939 
2940         /*
2941          * Enables bus-mastering on the device and calls
2942          * pcibios_set_master to do the needed arch specific settings
2943          */
2944         pci_set_master(pdev);
2945 
2946         netdev = alloc_etherdev(sizeof(struct atl1_adapter));
2947         if (!netdev) {
2948                 err = -ENOMEM;
2949                 goto err_alloc_etherdev;
2950         }
2951         SET_NETDEV_DEV(netdev, &pdev->dev);
2952 
2953         pci_set_drvdata(pdev, netdev);
2954         adapter = netdev_priv(netdev);
2955         adapter->netdev = netdev;
2956         adapter->pdev = pdev;
2957         adapter->hw.back = adapter;
2958         adapter->msg_enable = netif_msg_init(debug, atl1_default_msg);
2959 
2960         adapter->hw.hw_addr = pci_iomap(pdev, 0, 0);
2961         if (!adapter->hw.hw_addr) {
2962                 err = -EIO;
2963                 goto err_pci_iomap;
2964         }
2965         /* get device revision number */
2966         adapter->hw.dev_rev = ioread16(adapter->hw.hw_addr +
2967                 (REG_MASTER_CTRL + 2));
2968         if (netif_msg_probe(adapter))
2969                 dev_info(&pdev->dev, "version %s\n", ATLX_DRIVER_VERSION);
2970 
2971         /* set default ring resource counts */
2972         adapter->rfd_ring.count = adapter->rrd_ring.count = ATL1_DEFAULT_RFD;
2973         adapter->tpd_ring.count = ATL1_DEFAULT_TPD;
2974 
2975         adapter->mii.dev = netdev;
2976         adapter->mii.mdio_read = mdio_read;
2977         adapter->mii.mdio_write = mdio_write;
2978         adapter->mii.phy_id_mask = 0x1f;
2979         adapter->mii.reg_num_mask = 0x1f;
2980 
2981         netdev->netdev_ops = &atl1_netdev_ops;
2982         netdev->watchdog_timeo = 5 * HZ;
2983         netif_napi_add(netdev, &adapter->napi, atl1_rings_clean, 64);
2984 
2985         netdev->ethtool_ops = &atl1_ethtool_ops;
2986         adapter->bd_number = cards_found;
2987 
2988         /* setup the private structure */
2989         err = atl1_sw_init(adapter);
2990         if (err)
2991                 goto err_common;
2992 
2993         netdev->features = NETIF_F_HW_CSUM;
2994         netdev->features |= NETIF_F_SG;
2995         netdev->features |= (NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX);
2996 
2997         netdev->hw_features = NETIF_F_HW_CSUM | NETIF_F_SG | NETIF_F_TSO |
2998                               NETIF_F_HW_VLAN_CTAG_RX;
2999 
3000         /* is this valid? see atl1_setup_mac_ctrl() */
3001         netdev->features |= NETIF_F_RXCSUM;
3002 
3003         /* MTU range: 42 - 10218 */
3004         netdev->min_mtu = ETH_ZLEN - (ETH_HLEN + VLAN_HLEN);
3005         netdev->max_mtu = MAX_JUMBO_FRAME_SIZE -
3006                           (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
3007 
3008         /*
3009          * patch for some L1 of old version,
3010          * the final version of L1 may not need these
3011          * patches
3012          */
3013         /* atl1_pcie_patch(adapter); */
3014 
3015         /* really reset GPHY core */
3016         iowrite16(0, adapter->hw.hw_addr + REG_PHY_ENABLE);
3017 
3018         /*
3019          * reset the controller to
3020          * put the device in a known good starting state
3021          */
3022         if (atl1_reset_hw(&adapter->hw)) {
3023                 err = -EIO;
3024                 goto err_common;
3025         }
3026 
3027         /* copy the MAC address out of the EEPROM */
3028         if (atl1_read_mac_addr(&adapter->hw)) {
3029                 /* mark random mac */
3030                 netdev->addr_assign_type = NET_ADDR_RANDOM;
3031         }
3032         memcpy(netdev->dev_addr, adapter->hw.mac_addr, netdev->addr_len);
3033 
3034         if (!is_valid_ether_addr(netdev->dev_addr)) {
3035                 err = -EIO;
3036                 goto err_common;
3037         }
3038 
3039         atl1_check_options(adapter);
3040 
3041         /* pre-init the MAC, and setup link */
3042         err = atl1_init_hw(&adapter->hw);
3043         if (err) {
3044                 err = -EIO;
3045                 goto err_common;
3046         }
3047 
3048         atl1_pcie_patch(adapter);
3049         /* assume we have no link for now */
3050         netif_carrier_off(netdev);
3051 
3052         timer_setup(&adapter->phy_config_timer, atl1_phy_config, 0);
3053         adapter->phy_timer_pending = false;
3054 
3055         INIT_WORK(&adapter->reset_dev_task, atl1_reset_dev_task);
3056 
3057         INIT_WORK(&adapter->link_chg_task, atlx_link_chg_task);
3058 
3059         err = register_netdev(netdev);
3060         if (err)
3061                 goto err_common;
3062 
3063         cards_found++;
3064         atl1_via_workaround(adapter);
3065         return 0;
3066 
3067 err_common:
3068         pci_iounmap(pdev, adapter->hw.hw_addr);
3069 err_pci_iomap:
3070         free_netdev(netdev);
3071 err_alloc_etherdev:
3072         pci_release_regions(pdev);
3073 err_dma:
3074 err_request_regions:
3075         pci_disable_device(pdev);
3076         return err;
3077 }
3078 
3079 /**
3080  * atl1_remove - Device Removal Routine
3081  * @pdev: PCI device information struct
3082  *
3083  * atl1_remove is called by the PCI subsystem to alert the driver
3084  * that it should release a PCI device.  The could be caused by a
3085  * Hot-Plug event, or because the driver is going to be removed from
3086  * memory.
3087  */
3088 static void atl1_remove(struct pci_dev *pdev)
3089 {
3090         struct net_device *netdev = pci_get_drvdata(pdev);
3091         struct atl1_adapter *adapter;
3092         /* Device not available. Return. */
3093         if (!netdev)
3094                 return;
3095 
3096         adapter = netdev_priv(netdev);
3097 
3098         /*
3099          * Some atl1 boards lack persistent storage for their MAC, and get it
3100          * from the BIOS during POST.  If we've been messing with the MAC
3101          * address, we need to save the permanent one.
3102          */
3103         if (!ether_addr_equal_unaligned(adapter->hw.mac_addr,
3104                                         adapter->hw.perm_mac_addr)) {
3105                 memcpy(adapter->hw.mac_addr, adapter->hw.perm_mac_addr,
3106                         ETH_ALEN);
3107                 atl1_set_mac_addr(&adapter->hw);
3108         }
3109 
3110         iowrite16(0, adapter->hw.hw_addr + REG_PHY_ENABLE);
3111         unregister_netdev(netdev);
3112         pci_iounmap(pdev, adapter->hw.hw_addr);
3113         pci_release_regions(pdev);
3114         free_netdev(netdev);
3115         pci_disable_device(pdev);
3116 }
3117 
3118 static struct pci_driver atl1_driver = {
3119         .name = ATLX_DRIVER_NAME,
3120         .id_table = atl1_pci_tbl,
3121         .probe = atl1_probe,
3122         .remove = atl1_remove,
3123         .shutdown = atl1_shutdown,
3124         .driver.pm = &atl1_pm_ops,
3125 };
3126 
3127 struct atl1_stats {
3128         char stat_string[ETH_GSTRING_LEN];
3129         int sizeof_stat;
3130         int stat_offset;
3131 };
3132 
3133 #define ATL1_STAT(m) \
3134         sizeof(((struct atl1_adapter *)0)->m), offsetof(struct atl1_adapter, m)
3135 
3136 static struct atl1_stats atl1_gstrings_stats[] = {
3137         {"rx_packets", ATL1_STAT(soft_stats.rx_packets)},
3138         {"tx_packets", ATL1_STAT(soft_stats.tx_packets)},
3139         {"rx_bytes", ATL1_STAT(soft_stats.rx_bytes)},
3140         {"tx_bytes", ATL1_STAT(soft_stats.tx_bytes)},
3141         {"rx_errors", ATL1_STAT(soft_stats.rx_errors)},
3142         {"tx_errors", ATL1_STAT(soft_stats.tx_errors)},
3143         {"multicast", ATL1_STAT(soft_stats.multicast)},
3144         {"collisions", ATL1_STAT(soft_stats.collisions)},
3145         {"rx_length_errors", ATL1_STAT(soft_stats.rx_length_errors)},
3146         {"rx_over_errors", ATL1_STAT(soft_stats.rx_missed_errors)},
3147         {"rx_crc_errors", ATL1_STAT(soft_stats.rx_crc_errors)},
3148         {"rx_frame_errors", ATL1_STAT(soft_stats.rx_frame_errors)},
3149         {"rx_fifo_errors", ATL1_STAT(soft_stats.rx_fifo_errors)},
3150         {"rx_missed_errors", ATL1_STAT(soft_stats.rx_missed_errors)},
3151         {"tx_aborted_errors", ATL1_STAT(soft_stats.tx_aborted_errors)},
3152         {"tx_carrier_errors", ATL1_STAT(soft_stats.tx_carrier_errors)},
3153         {"tx_fifo_errors", ATL1_STAT(soft_stats.tx_fifo_errors)},
3154         {"tx_window_errors", ATL1_STAT(soft_stats.tx_window_errors)},
3155         {"tx_abort_exce_coll", ATL1_STAT(soft_stats.excecol)},
3156         {"tx_abort_late_coll", ATL1_STAT(soft_stats.latecol)},
3157         {"tx_deferred_ok", ATL1_STAT(soft_stats.deffer)},
3158         {"tx_single_coll_ok", ATL1_STAT(soft_stats.scc)},
3159         {"tx_multi_coll_ok", ATL1_STAT(soft_stats.mcc)},
3160         {"tx_underrun", ATL1_STAT(soft_stats.tx_underrun)},
3161         {"tx_trunc", ATL1_STAT(soft_stats.tx_trunc)},
3162         {"tx_pause", ATL1_STAT(soft_stats.tx_pause)},
3163         {"rx_pause", ATL1_STAT(soft_stats.rx_pause)},
3164         {"rx_rrd_ov", ATL1_STAT(soft_stats.rx_rrd_ov)},
3165         {"rx_trunc", ATL1_STAT(soft_stats.rx_trunc)}
3166 };
3167 
3168 static void atl1_get_ethtool_stats(struct net_device *netdev,
3169         struct ethtool_stats *stats, u64 *data)
3170 {
3171         struct atl1_adapter *adapter = netdev_priv(netdev);
3172         int i;
3173         char *p;
3174 
3175         for (i = 0; i < ARRAY_SIZE(atl1_gstrings_stats); i++) {
3176                 p = (char *)adapter+atl1_gstrings_stats[i].stat_offset;
3177                 data[i] = (atl1_gstrings_stats[i].sizeof_stat ==
3178                         sizeof(u64)) ? *(u64 *)p : *(u32 *)p;
3179         }
3180 
3181 }
3182 
3183 static int atl1_get_sset_count(struct net_device *netdev, int sset)
3184 {
3185         switch (sset) {
3186         case ETH_SS_STATS:
3187                 return ARRAY_SIZE(atl1_gstrings_stats);
3188         default:
3189                 return -EOPNOTSUPP;
3190         }
3191 }
3192 
3193 static int atl1_get_link_ksettings(struct net_device *netdev,
3194                                    struct ethtool_link_ksettings *cmd)
3195 {
3196         struct atl1_adapter *adapter = netdev_priv(netdev);
3197         struct atl1_hw *hw = &adapter->hw;
3198         u32 supported, advertising;
3199 
3200         supported = (SUPPORTED_10baseT_Half |
3201                            SUPPORTED_10baseT_Full |
3202                            SUPPORTED_100baseT_Half |
3203                            SUPPORTED_100baseT_Full |
3204                            SUPPORTED_1000baseT_Full |
3205                            SUPPORTED_Autoneg | SUPPORTED_TP);
3206         advertising = ADVERTISED_TP;
3207         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3208             hw->media_type == MEDIA_TYPE_1000M_FULL) {
3209                 advertising |= ADVERTISED_Autoneg;
3210                 if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR) {
3211                         advertising |= ADVERTISED_Autoneg;
3212                         advertising |=
3213                             (ADVERTISED_10baseT_Half |
3214                              ADVERTISED_10baseT_Full |
3215                              ADVERTISED_100baseT_Half |
3216                              ADVERTISED_100baseT_Full |
3217                              ADVERTISED_1000baseT_Full);
3218                 } else
3219                         advertising |= (ADVERTISED_1000baseT_Full);
3220         }
3221         cmd->base.port = PORT_TP;
3222         cmd->base.phy_address = 0;
3223 
3224         if (netif_carrier_ok(adapter->netdev)) {
3225                 u16 link_speed, link_duplex;
3226                 atl1_get_speed_and_duplex(hw, &link_speed, &link_duplex);
3227                 cmd->base.speed = link_speed;
3228                 if (link_duplex == FULL_DUPLEX)
3229                         cmd->base.duplex = DUPLEX_FULL;
3230                 else
3231                         cmd->base.duplex = DUPLEX_HALF;
3232         } else {
3233                 cmd->base.speed = SPEED_UNKNOWN;
3234                 cmd->base.duplex = DUPLEX_UNKNOWN;
3235         }
3236         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3237             hw->media_type == MEDIA_TYPE_1000M_FULL)
3238                 cmd->base.autoneg = AUTONEG_ENABLE;
3239         else
3240                 cmd->base.autoneg = AUTONEG_DISABLE;
3241 
3242         ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported,
3243                                                 supported);
3244         ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.advertising,
3245                                                 advertising);
3246 
3247         return 0;
3248 }
3249 
3250 static int atl1_set_link_ksettings(struct net_device *netdev,
3251                                    const struct ethtool_link_ksettings *cmd)
3252 {
3253         struct atl1_adapter *adapter = netdev_priv(netdev);
3254         struct atl1_hw *hw = &adapter->hw;
3255         u16 phy_data;
3256         int ret_val = 0;
3257         u16 old_media_type = hw->media_type;
3258 
3259         if (netif_running(adapter->netdev)) {
3260                 if (netif_msg_link(adapter))
3261                         dev_dbg(&adapter->pdev->dev,
3262                                 "ethtool shutting down adapter\n");
3263                 atl1_down(adapter);
3264         }
3265 
3266         if (cmd->base.autoneg == AUTONEG_ENABLE)
3267                 hw->media_type = MEDIA_TYPE_AUTO_SENSOR;
3268         else {
3269                 u32 speed = cmd->base.speed;
3270                 if (speed == SPEED_1000) {
3271                         if (cmd->base.duplex != DUPLEX_FULL) {
3272                                 if (netif_msg_link(adapter))
3273                                         dev_warn(&adapter->pdev->dev,
3274                                                 "1000M half is invalid\n");
3275                                 ret_val = -EINVAL;
3276                                 goto exit_sset;
3277                         }
3278                         hw->media_type = MEDIA_TYPE_1000M_FULL;
3279                 } else if (speed == SPEED_100) {
3280                         if (cmd->base.duplex == DUPLEX_FULL)
3281                                 hw->media_type = MEDIA_TYPE_100M_FULL;
3282                         else
3283                                 hw->media_type = MEDIA_TYPE_100M_HALF;
3284                 } else {
3285                         if (cmd->base.duplex == DUPLEX_FULL)
3286                                 hw->media_type = MEDIA_TYPE_10M_FULL;
3287                         else
3288                                 hw->media_type = MEDIA_TYPE_10M_HALF;
3289                 }
3290         }
3291 
3292         if (atl1_phy_setup_autoneg_adv(hw)) {
3293                 ret_val = -EINVAL;
3294                 if (netif_msg_link(adapter))
3295                         dev_warn(&adapter->pdev->dev,
3296                                 "invalid ethtool speed/duplex setting\n");
3297                 goto exit_sset;
3298         }
3299         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3300             hw->media_type == MEDIA_TYPE_1000M_FULL)
3301                 phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
3302         else {
3303                 switch (hw->media_type) {
3304                 case MEDIA_TYPE_100M_FULL:
3305                         phy_data =
3306                             MII_CR_FULL_DUPLEX | MII_CR_SPEED_100 |
3307                             MII_CR_RESET;
3308                         break;
3309                 case MEDIA_TYPE_100M_HALF:
3310                         phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
3311                         break;
3312                 case MEDIA_TYPE_10M_FULL:
3313                         phy_data =
3314                             MII_CR_FULL_DUPLEX | MII_CR_SPEED_10 | MII_CR_RESET;
3315                         break;
3316                 default:
3317                         /* MEDIA_TYPE_10M_HALF: */
3318                         phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
3319                         break;
3320                 }
3321         }
3322         atl1_write_phy_reg(hw, MII_BMCR, phy_data);
3323 exit_sset:
3324         if (ret_val)
3325                 hw->media_type = old_media_type;
3326 
3327         if (netif_running(adapter->netdev)) {
3328                 if (netif_msg_link(adapter))
3329                         dev_dbg(&adapter->pdev->dev,
3330                                 "ethtool starting adapter\n");
3331                 atl1_up(adapter);
3332         } else if (!ret_val) {
3333                 if (netif_msg_link(adapter))
3334                         dev_dbg(&adapter->pdev->dev,
3335                                 "ethtool resetting adapter\n");
3336                 atl1_reset(adapter);
3337         }
3338         return ret_val;
3339 }
3340 
3341 static void atl1_get_drvinfo(struct net_device *netdev,
3342         struct ethtool_drvinfo *drvinfo)
3343 {
3344         struct atl1_adapter *adapter = netdev_priv(netdev);
3345 
3346         strlcpy(drvinfo->driver, ATLX_DRIVER_NAME, sizeof(drvinfo->driver));
3347         strlcpy(drvinfo->version, ATLX_DRIVER_VERSION,
3348                 sizeof(drvinfo->version));
3349         strlcpy(drvinfo->bus_info, pci_name(adapter->pdev),
3350                 sizeof(drvinfo->bus_info));
3351 }
3352 
3353 static void atl1_get_wol(struct net_device *netdev,
3354         struct ethtool_wolinfo *wol)
3355 {
3356         struct atl1_adapter *adapter = netdev_priv(netdev);
3357 
3358         wol->supported = WAKE_MAGIC;
3359         wol->wolopts = 0;
3360         if (adapter->wol & ATLX_WUFC_MAG)
3361                 wol->wolopts |= WAKE_MAGIC;
3362 }
3363 
3364 static int atl1_set_wol(struct net_device *netdev,
3365         struct ethtool_wolinfo *wol)
3366 {
3367         struct atl1_adapter *adapter = netdev_priv(netdev);
3368 
3369         if (wol->wolopts & (WAKE_PHY | WAKE_UCAST | WAKE_MCAST | WAKE_BCAST |
3370                 WAKE_ARP | WAKE_MAGICSECURE))
3371                 return -EOPNOTSUPP;
3372         adapter->wol = 0;
3373         if (wol->wolopts & WAKE_MAGIC)
3374                 adapter->wol |= ATLX_WUFC_MAG;
3375 
3376         device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
3377 
3378         return 0;
3379 }
3380 
3381 static u32 atl1_get_msglevel(struct net_device *netdev)
3382 {
3383         struct atl1_adapter *adapter = netdev_priv(netdev);
3384         return adapter->msg_enable;
3385 }
3386 
3387 static void atl1_set_msglevel(struct net_device *netdev, u32 value)
3388 {
3389         struct atl1_adapter *adapter = netdev_priv(netdev);
3390         adapter->msg_enable = value;
3391 }
3392 
3393 static int atl1_get_regs_len(struct net_device *netdev)
3394 {
3395         return ATL1_REG_COUNT * sizeof(u32);
3396 }
3397 
3398 static void atl1_get_regs(struct net_device *netdev, struct ethtool_regs *regs,
3399         void *p)
3400 {
3401         struct atl1_adapter *adapter = netdev_priv(netdev);
3402         struct atl1_hw *hw = &adapter->hw;
3403         unsigned int i;
3404         u32 *regbuf = p;
3405 
3406         for (i = 0; i < ATL1_REG_COUNT; i++) {
3407                 /*
3408                  * This switch statement avoids reserved regions
3409                  * of register space.
3410                  */
3411                 switch (i) {
3412                 case 6 ... 9:
3413                 case 14:
3414                 case 29 ... 31:
3415                 case 34 ... 63:
3416                 case 75 ... 127:
3417                 case 136 ... 1023:
3418                 case 1027 ... 1087:
3419                 case 1091 ... 1151:
3420                 case 1194 ... 1195:
3421                 case 1200 ... 1201:
3422                 case 1206 ... 1213:
3423                 case 1216 ... 1279:
3424                 case 1290 ... 1311:
3425                 case 1323 ... 1343:
3426                 case 1358 ... 1359:
3427                 case 1368 ... 1375:
3428                 case 1378 ... 1383:
3429                 case 1388 ... 1391:
3430                 case 1393 ... 1395:
3431                 case 1402 ... 1403:
3432                 case 1410 ... 1471:
3433                 case 1522 ... 1535:
3434                         /* reserved region; don't read it */
3435                         regbuf[i] = 0;
3436                         break;
3437                 default:
3438                         /* unreserved region */
3439                         regbuf[i] = ioread32(hw->hw_addr + (i * sizeof(u32)));
3440                 }
3441         }
3442 }
3443 
3444 static void atl1_get_ringparam(struct net_device *netdev,
3445         struct ethtool_ringparam *ring)
3446 {
3447         struct atl1_adapter *adapter = netdev_priv(netdev);
3448         struct atl1_tpd_ring *txdr = &adapter->tpd_ring;
3449         struct atl1_rfd_ring *rxdr = &adapter->rfd_ring;
3450 
3451         ring->rx_max_pending = ATL1_MAX_RFD;
3452         ring->tx_max_pending = ATL1_MAX_TPD;
3453         ring->rx_pending = rxdr->count;
3454         ring->tx_pending = txdr->count;
3455 }
3456 
3457 static int atl1_set_ringparam(struct net_device *netdev,
3458         struct ethtool_ringparam *ring)
3459 {
3460         struct atl1_adapter *adapter = netdev_priv(netdev);
3461         struct atl1_tpd_ring *tpdr = &adapter->tpd_ring;
3462         struct atl1_rrd_ring *rrdr = &adapter->rrd_ring;
3463         struct atl1_rfd_ring *rfdr = &adapter->rfd_ring;
3464 
3465         struct atl1_tpd_ring tpd_old, tpd_new;
3466         struct atl1_rfd_ring rfd_old, rfd_new;
3467         struct atl1_rrd_ring rrd_old, rrd_new;
3468         struct atl1_ring_header rhdr_old, rhdr_new;
3469         struct atl1_smb smb;
3470         struct atl1_cmb cmb;
3471         int err;
3472 
3473         tpd_old = adapter->tpd_ring;
3474         rfd_old = adapter->rfd_ring;
3475         rrd_old = adapter->rrd_ring;
3476         rhdr_old = adapter->ring_header;
3477 
3478         if (netif_running(adapter->netdev))
3479                 atl1_down(adapter);
3480 
3481         rfdr->count = (u16) max(ring->rx_pending, (u32) ATL1_MIN_RFD);
3482         rfdr->count = rfdr->count > ATL1_MAX_RFD ? ATL1_MAX_RFD :
3483                         rfdr->count;
3484         rfdr->count = (rfdr->count + 3) & ~3;
3485         rrdr->count = rfdr->count;
3486 
3487         tpdr->count = (u16) max(ring->tx_pending, (u32) ATL1_MIN_TPD);
3488         tpdr->count = tpdr->count > ATL1_MAX_TPD ? ATL1_MAX_TPD :
3489                         tpdr->count;
3490         tpdr->count = (tpdr->count + 3) & ~3;
3491 
3492         if (netif_running(adapter->netdev)) {
3493                 /* try to get new resources before deleting old */
3494                 err = atl1_setup_ring_resources(adapter);
3495                 if (err)
3496                         goto err_setup_ring;
3497 
3498                 /*
3499                  * save the new, restore the old in order to free it,
3500                  * then restore the new back again
3501                  */
3502 
3503                 rfd_new = adapter->rfd_ring;
3504                 rrd_new = adapter->rrd_ring;
3505                 tpd_new = adapter->tpd_ring;
3506                 rhdr_new = adapter->ring_header;
3507                 adapter->rfd_ring = rfd_old;
3508                 adapter->rrd_ring = rrd_old;
3509                 adapter->tpd_ring = tpd_old;
3510                 adapter->ring_header = rhdr_old;
3511                 /*
3512                  * Save SMB and CMB, since atl1_free_ring_resources
3513                  * will clear them.
3514                  */
3515                 smb = adapter->smb;
3516                 cmb = adapter->cmb;
3517                 atl1_free_ring_resources(adapter);
3518                 adapter->rfd_ring = rfd_new;
3519                 adapter->rrd_ring = rrd_new;
3520                 adapter->tpd_ring = tpd_new;
3521                 adapter->ring_header = rhdr_new;
3522                 adapter->smb = smb;
3523                 adapter->cmb = cmb;
3524 
3525                 err = atl1_up(adapter);
3526                 if (err)
3527                         return err;
3528         }
3529         return 0;
3530 
3531 err_setup_ring:
3532         adapter->rfd_ring = rfd_old;
3533         adapter->rrd_ring = rrd_old;
3534         adapter->tpd_ring = tpd_old;
3535         adapter->ring_header = rhdr_old;
3536         atl1_up(adapter);
3537         return err;
3538 }
3539 
3540 static void atl1_get_pauseparam(struct net_device *netdev,
3541         struct ethtool_pauseparam *epause)
3542 {
3543         struct atl1_adapter *adapter = netdev_priv(netdev);
3544         struct atl1_hw *hw = &adapter->hw;
3545 
3546         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3547             hw->media_type == MEDIA_TYPE_1000M_FULL) {
3548                 epause->autoneg = AUTONEG_ENABLE;
3549         } else {
3550                 epause->autoneg = AUTONEG_DISABLE;
3551         }
3552         epause->rx_pause = 1;
3553         epause->tx_pause = 1;
3554 }
3555 
3556 static int atl1_set_pauseparam(struct net_device *netdev,
3557         struct ethtool_pauseparam *epause)
3558 {
3559         struct atl1_adapter *adapter = netdev_priv(netdev);
3560         struct atl1_hw *hw = &adapter->hw;
3561 
3562         if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3563             hw->media_type == MEDIA_TYPE_1000M_FULL) {
3564                 epause->autoneg = AUTONEG_ENABLE;
3565         } else {
3566                 epause->autoneg = AUTONEG_DISABLE;
3567         }
3568 
3569         epause->rx_pause = 1;
3570         epause->tx_pause = 1;
3571 
3572         return 0;
3573 }
3574 
3575 static void atl1_get_strings(struct net_device *netdev, u32 stringset,
3576         u8 *data)
3577 {
3578         u8 *p = data;
3579         int i;
3580 
3581         switch (stringset) {
3582         case ETH_SS_STATS:
3583                 for (i = 0; i < ARRAY_SIZE(atl1_gstrings_stats); i++) {
3584                         memcpy(p, atl1_gstrings_stats[i].stat_string,
3585                                 ETH_GSTRING_LEN);
3586                         p += ETH_GSTRING_LEN;
3587                 }
3588                 break;
3589         }
3590 }
3591 
3592 static int atl1_nway_reset(struct net_device *netdev)
3593 {
3594         struct atl1_adapter *adapter = netdev_priv(netdev);
3595         struct atl1_hw *hw = &adapter->hw;
3596 
3597         if (netif_running(netdev)) {
3598                 u16 phy_data;
3599                 atl1_down(adapter);
3600 
3601                 if (hw->media_type == MEDIA_TYPE_AUTO_SENSOR ||
3602                         hw->media_type == MEDIA_TYPE_1000M_FULL) {
3603                         phy_data = MII_CR_RESET | MII_CR_AUTO_NEG_EN;
3604                 } else {
3605                         switch (hw->media_type) {
3606                         case MEDIA_TYPE_100M_FULL:
3607                                 phy_data = MII_CR_FULL_DUPLEX |
3608                                         MII_CR_SPEED_100 | MII_CR_RESET;
3609                                 break;
3610                         case MEDIA_TYPE_100M_HALF:
3611                                 phy_data = MII_CR_SPEED_100 | MII_CR_RESET;
3612                                 break;
3613                         case MEDIA_TYPE_10M_FULL:
3614                                 phy_data = MII_CR_FULL_DUPLEX |
3615                                         MII_CR_SPEED_10 | MII_CR_RESET;
3616                                 break;
3617                         default:
3618                                 /* MEDIA_TYPE_10M_HALF */
3619                                 phy_data = MII_CR_SPEED_10 | MII_CR_RESET;
3620                         }
3621                 }
3622                 atl1_write_phy_reg(hw, MII_BMCR, phy_data);
3623                 atl1_up(adapter);
3624         }
3625         return 0;
3626 }
3627 
3628 static const struct ethtool_ops atl1_ethtool_ops = {
3629         .get_drvinfo            = atl1_get_drvinfo,
3630         .get_wol                = atl1_get_wol,
3631         .set_wol                = atl1_set_wol,
3632         .get_msglevel           = atl1_get_msglevel,
3633         .set_msglevel           = atl1_set_msglevel,
3634         .get_regs_len           = atl1_get_regs_len,
3635         .get_regs               = atl1_get_regs,
3636         .get_ringparam          = atl1_get_ringparam,
3637         .set_ringparam          = atl1_set_ringparam,
3638         .get_pauseparam         = atl1_get_pauseparam,
3639         .set_pauseparam         = atl1_set_pauseparam,
3640         .get_link               = ethtool_op_get_link,
3641         .get_strings            = atl1_get_strings,
3642         .nway_reset             = atl1_nway_reset,
3643         .get_ethtool_stats      = atl1_get_ethtool_stats,
3644         .get_sset_count         = atl1_get_sset_count,
3645         .get_link_ksettings     = atl1_get_link_ksettings,
3646         .set_link_ksettings     = atl1_set_link_ksettings,
3647 };
3648 
3649 module_pci_driver(atl1_driver);

/* [<][>][^][v][top][bottom][index][help] */