drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
pch_gbe_validate_option
pch_gbe_check_copper_options
pch_gbe_check_options
   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Copyright (C) 1999 - 2010 Intel Corporation.
   4  * Copyright (C) 2010 OKI SEMICONDUCTOR Co., LTD.
   5  *
   6  * This code was derived from the Intel e1000e Linux driver.
   7  */
   8 
   9 #include "pch_gbe.h"
  10 #include <linux/module.h>       /* for __MODULE_STRING */
  11 
  12 #define OPTION_UNSET   -1
  13 #define OPTION_DISABLED 0
  14 #define OPTION_ENABLED  1
  15 
  16 /**
  17  * TxDescriptors - Transmit Descriptor Count
  18  * @Valid Range:   PCH_GBE_MIN_TXD - PCH_GBE_MAX_TXD
  19  * @Default Value: PCH_GBE_DEFAULT_TXD
  20  */
  21 static int TxDescriptors = OPTION_UNSET;
  22 module_param(TxDescriptors, int, 0);
  23 MODULE_PARM_DESC(TxDescriptors, "Number of transmit descriptors");
  24 
  25 /**
  26  * RxDescriptors -Receive Descriptor Count
  27  * @Valid Range:   PCH_GBE_MIN_RXD - PCH_GBE_MAX_RXD
  28  * @Default Value: PCH_GBE_DEFAULT_RXD
  29  */
  30 static int RxDescriptors = OPTION_UNSET;
  31 module_param(RxDescriptors, int, 0);
  32 MODULE_PARM_DESC(RxDescriptors, "Number of receive descriptors");
  33 
  34 /**
  35  * Speed - User Specified Speed Override
  36  * @Valid Range: 0, 10, 100, 1000
  37  *   - 0:    auto-negotiate at all supported speeds
  38  *   - 10:   only link at 10 Mbps
  39  *   - 100:  only link at 100 Mbps
  40  *   - 1000: only link at 1000 Mbps
  41  * @Default Value: 0
  42  */
  43 static int Speed = OPTION_UNSET;
  44 module_param(Speed, int, 0);
  45 MODULE_PARM_DESC(Speed, "Speed setting");
  46 
  47 /**
  48  * Duplex - User Specified Duplex Override
  49  * @Valid Range: 0-2
  50  *   - 0:  auto-negotiate for duplex
  51  *   - 1:  only link at half duplex
  52  *   - 2:  only link at full duplex
  53  * @Default Value: 0
  54  */
  55 static int Duplex = OPTION_UNSET;
  56 module_param(Duplex, int, 0);
  57 MODULE_PARM_DESC(Duplex, "Duplex setting");
  58 
  59 #define HALF_DUPLEX 1
  60 #define FULL_DUPLEX 2
  61 
  62 /**
  63  * AutoNeg - Auto-negotiation Advertisement Override
  64  * @Valid Range: 0x01-0x0F, 0x20-0x2F
  65  *
  66  *       The AutoNeg value is a bit mask describing which speed and duplex
  67  *       combinations should be advertised during auto-negotiation.
  68  *       The supported speed and duplex modes are listed below
  69  *
  70  *       Bit           7     6     5      4      3     2     1      0
  71  *       Speed (Mbps)  N/A   N/A   1000   N/A    100   100   10     10
  72  *       Duplex                    Full          Full  Half  Full   Half
  73  *
  74  * @Default Value: 0x2F (copper)
  75  */
  76 static int AutoNeg = OPTION_UNSET;
  77 module_param(AutoNeg, int, 0);
  78 MODULE_PARM_DESC(AutoNeg, "Advertised auto-negotiation setting");
  79 
  80 #define PHY_ADVERTISE_10_HALF      0x0001
  81 #define PHY_ADVERTISE_10_FULL      0x0002
  82 #define PHY_ADVERTISE_100_HALF     0x0004
  83 #define PHY_ADVERTISE_100_FULL     0x0008
  84 #define PHY_ADVERTISE_1000_HALF    0x0010 /* Not used, just FYI */
  85 #define PHY_ADVERTISE_1000_FULL    0x0020
  86 #define PCH_AUTONEG_ADVERTISE_DEFAULT   0x2F
  87 
  88 /**
  89  * FlowControl - User Specified Flow Control Override
  90  * @Valid Range: 0-3
  91  *    - 0:  No Flow Control
  92  *    - 1:  Rx only, respond to PAUSE frames but do not generate them
  93  *    - 2:  Tx only, generate PAUSE frames but ignore them on receive
  94  *    - 3:  Full Flow Control Support
  95  * @Default Value: Read flow control settings from the EEPROM
  96  */
  97 static int FlowControl = OPTION_UNSET;
  98 module_param(FlowControl, int, 0);
  99 MODULE_PARM_DESC(FlowControl, "Flow Control setting");
 100 
 101 /*
 102  * XsumRX - Receive Checksum Offload Enable/Disable
 103  * @Valid Range: 0, 1
 104  *    - 0:  disables all checksum offload
 105  *    - 1:  enables receive IP/TCP/UDP checksum offload
 106  * @Default Value: PCH_GBE_DEFAULT_RX_CSUM
 107  */
 108 static int XsumRX = OPTION_UNSET;
 109 module_param(XsumRX, int, 0);
 110 MODULE_PARM_DESC(XsumRX, "Disable or enable Receive Checksum offload");
 111 
 112 #define PCH_GBE_DEFAULT_RX_CSUM             true        /* trueorfalse */
 113 
 114 /*
 115  * XsumTX - Transmit Checksum Offload Enable/Disable
 116  * @Valid Range: 0, 1
 117  *    - 0:  disables all checksum offload
 118  *    - 1:  enables transmit IP/TCP/UDP checksum offload
 119  * @Default Value: PCH_GBE_DEFAULT_TX_CSUM
 120  */
 121 static int XsumTX = OPTION_UNSET;
 122 module_param(XsumTX, int, 0);
 123 MODULE_PARM_DESC(XsumTX, "Disable or enable Transmit Checksum offload");
 124 
 125 #define PCH_GBE_DEFAULT_TX_CSUM             true        /* trueorfalse */
 126 
 127 /**
 128  * pch_gbe_option - Force the MAC's flow control settings
 129  * @hw:             Pointer to the HW structure
 130  * Returns:
 131  *      0:                      Successful.
 132  *      Negative value:         Failed.
 133  */
 134 struct pch_gbe_option {
 135         enum { enable_option, range_option, list_option } type;
 136         char *name;
 137         char *err;
 138         int  def;
 139         union {
 140                 struct { /* range_option info */
 141                         int min;
 142                         int max;
 143                 } r;
 144                 struct { /* list_option info */
 145                         int nr;
 146                         const struct pch_gbe_opt_list { int i; char *str; } *p;
 147                 } l;
 148         } arg;
 149 };
 150 
 151 static const struct pch_gbe_opt_list speed_list[] = {
 152         { 0, "" },
 153         { SPEED_10, "" },
 154         { SPEED_100, "" },
 155         { SPEED_1000, "" }
 156 };
 157 
 158 static const struct pch_gbe_opt_list dplx_list[] = {
 159         { 0, "" },
 160         { HALF_DUPLEX, "" },
 161         { FULL_DUPLEX, "" }
 162 };
 163 
 164 static const struct pch_gbe_opt_list an_list[] =
 165         #define AA "AutoNeg advertising "
 166         {{ 0x01, AA "10/HD" },
 167          { 0x02, AA "10/FD" },
 168          { 0x03, AA "10/FD, 10/HD" },
 169          { 0x04, AA "100/HD" },
 170          { 0x05, AA "100/HD, 10/HD" },
 171          { 0x06, AA "100/HD, 10/FD" },
 172          { 0x07, AA "100/HD, 10/FD, 10/HD" },
 173          { 0x08, AA "100/FD" },
 174          { 0x09, AA "100/FD, 10/HD" },
 175          { 0x0a, AA "100/FD, 10/FD" },
 176          { 0x0b, AA "100/FD, 10/FD, 10/HD" },
 177          { 0x0c, AA "100/FD, 100/HD" },
 178          { 0x0d, AA "100/FD, 100/HD, 10/HD" },
 179          { 0x0e, AA "100/FD, 100/HD, 10/FD" },
 180          { 0x0f, AA "100/FD, 100/HD, 10/FD, 10/HD" },
 181          { 0x20, AA "1000/FD" },
 182          { 0x21, AA "1000/FD, 10/HD" },
 183          { 0x22, AA "1000/FD, 10/FD" },
 184          { 0x23, AA "1000/FD, 10/FD, 10/HD" },
 185          { 0x24, AA "1000/FD, 100/HD" },
 186          { 0x25, AA "1000/FD, 100/HD, 10/HD" },
 187          { 0x26, AA "1000/FD, 100/HD, 10/FD" },
 188          { 0x27, AA "1000/FD, 100/HD, 10/FD, 10/HD" },
 189          { 0x28, AA "1000/FD, 100/FD" },
 190          { 0x29, AA "1000/FD, 100/FD, 10/HD" },
 191          { 0x2a, AA "1000/FD, 100/FD, 10/FD" },
 192          { 0x2b, AA "1000/FD, 100/FD, 10/FD, 10/HD" },
 193          { 0x2c, AA "1000/FD, 100/FD, 100/HD" },
 194          { 0x2d, AA "1000/FD, 100/FD, 100/HD, 10/HD" },
 195          { 0x2e, AA "1000/FD, 100/FD, 100/HD, 10/FD" },
 196          { 0x2f, AA "1000/FD, 100/FD, 100/HD, 10/FD, 10/HD" }
 197 };
 198 
 199 static const struct pch_gbe_opt_list fc_list[] = {
 200         { PCH_GBE_FC_NONE, "Flow Control Disabled" },
 201         { PCH_GBE_FC_RX_PAUSE, "Flow Control Receive Only" },
 202         { PCH_GBE_FC_TX_PAUSE, "Flow Control Transmit Only" },
 203         { PCH_GBE_FC_FULL, "Flow Control Enabled" }
 204 };
 205 
 206 /**
 207  * pch_gbe_validate_option - Validate option
 208  * @value:    value
 209  * @opt:      option
 210  * @adapter:  Board private structure
 211  * Returns:
 212  *      0:                      Successful.
 213  *      Negative value:         Failed.
 214  */
 215 static int pch_gbe_validate_option(int *value,
 216                                     const struct pch_gbe_option *opt,
 217                                     struct pch_gbe_adapter *adapter)
 218 {
 219         if (*value == OPTION_UNSET) {
 220                 *value = opt->def;
 221                 return 0;
 222         }
 223 
 224         switch (opt->type) {
 225         case enable_option:
 226                 switch (*value) {
 227                 case OPTION_ENABLED:
 228                         netdev_dbg(adapter->netdev, "%s Enabled\n", opt->name);
 229                         return 0;
 230                 case OPTION_DISABLED:
 231                         netdev_dbg(adapter->netdev, "%s Disabled\n", opt->name);
 232                         return 0;
 233                 }
 234                 break;
 235         case range_option:
 236                 if (*value >= opt->arg.r.min && *value <= opt->arg.r.max) {
 237                         netdev_dbg(adapter->netdev, "%s set to %i\n",
 238                                    opt->name, *value);
 239                         return 0;
 240                 }
 241                 break;
 242         case list_option: {
 243                 int i;
 244                 const struct pch_gbe_opt_list *ent;
 245 
 246                 for (i = 0; i < opt->arg.l.nr; i++) {
 247                         ent = &opt->arg.l.p[i];
 248                         if (*value == ent->i) {
 249                                 if (ent->str[0] != '\0')
 250                                         netdev_dbg(adapter->netdev, "%s\n",
 251                                                    ent->str);
 252                                 return 0;
 253                         }
 254                 }
 255         }
 256                 break;
 257         default:
 258                 BUG();
 259         }
 260 
 261         netdev_dbg(adapter->netdev, "Invalid %s value specified (%i) %s\n",
 262                    opt->name, *value, opt->err);
 263         *value = opt->def;
 264         return -1;
 265 }
 266 
 267 /**
 268  * pch_gbe_check_copper_options - Range Checking for Link Options, Copper Version
 269  * @adapter:  Board private structure
 270  */
 271 static void pch_gbe_check_copper_options(struct pch_gbe_adapter *adapter)
 272 {
 273         struct pch_gbe_hw *hw = &adapter->hw;
 274         int speed, dplx;
 275 
 276         { /* Speed */
 277                 static const struct pch_gbe_option opt = {
 278                         .type = list_option,
 279                         .name = "Speed",
 280                         .err  = "parameter ignored",
 281                         .def  = 0,
 282                         .arg  = { .l = { .nr = (int)ARRAY_SIZE(speed_list),
 283                                          .p = speed_list } }
 284                 };
 285                 speed = Speed;
 286                 pch_gbe_validate_option(&speed, &opt, adapter);
 287         }
 288         { /* Duplex */
 289                 static const struct pch_gbe_option opt = {
 290                         .type = list_option,
 291                         .name = "Duplex",
 292                         .err  = "parameter ignored",
 293                         .def  = 0,
 294                         .arg  = { .l = { .nr = (int)ARRAY_SIZE(dplx_list),
 295                                          .p = dplx_list } }
 296                 };
 297                 dplx = Duplex;
 298                 pch_gbe_validate_option(&dplx, &opt, adapter);
 299         }
 300 
 301         { /* Autoneg */
 302                 static const struct pch_gbe_option opt = {
 303                         .type = list_option,
 304                         .name = "AutoNeg",
 305                         .err  = "parameter ignored",
 306                         .def  = PCH_AUTONEG_ADVERTISE_DEFAULT,
 307                         .arg  = { .l = { .nr = (int)ARRAY_SIZE(an_list),
 308                                          .p = an_list} }
 309                 };
 310                 if (speed || dplx) {
 311                         netdev_dbg(adapter->netdev,
 312                                    "AutoNeg specified along with Speed or Duplex, AutoNeg parameter ignored\n");
 313                         hw->phy.autoneg_advertised = opt.def;
 314                 } else {
 315                         int tmp = AutoNeg;
 316 
 317                         pch_gbe_validate_option(&tmp, &opt, adapter);
 318                         hw->phy.autoneg_advertised = tmp;
 319                 }
 320         }
 321 
 322         switch (speed + dplx) {
 323         case 0:
 324                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 325                 if ((speed || dplx))
 326                         netdev_dbg(adapter->netdev,
 327                                    "Speed and duplex autonegotiation enabled\n");
 328                 hw->mac.link_speed = SPEED_10;
 329                 hw->mac.link_duplex = DUPLEX_HALF;
 330                 break;
 331         case HALF_DUPLEX:
 332                 netdev_dbg(adapter->netdev,
 333                            "Half Duplex specified without Speed\n");
 334                 netdev_dbg(adapter->netdev,
 335                            "Using Autonegotiation at Half Duplex only\n");
 336                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 337                 hw->phy.autoneg_advertised = PHY_ADVERTISE_10_HALF |
 338                                                 PHY_ADVERTISE_100_HALF;
 339                 hw->mac.link_speed = SPEED_10;
 340                 hw->mac.link_duplex = DUPLEX_HALF;
 341                 break;
 342         case FULL_DUPLEX:
 343                 netdev_dbg(adapter->netdev,
 344                            "Full Duplex specified without Speed\n");
 345                 netdev_dbg(adapter->netdev,
 346                            "Using Autonegotiation at Full Duplex only\n");
 347                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 348                 hw->phy.autoneg_advertised = PHY_ADVERTISE_10_FULL |
 349                                                 PHY_ADVERTISE_100_FULL |
 350                                                 PHY_ADVERTISE_1000_FULL;
 351                 hw->mac.link_speed = SPEED_10;
 352                 hw->mac.link_duplex = DUPLEX_FULL;
 353                 break;
 354         case SPEED_10:
 355                 netdev_dbg(adapter->netdev,
 356                            "10 Mbps Speed specified without Duplex\n");
 357                 netdev_dbg(adapter->netdev,
 358                            "Using Autonegotiation at 10 Mbps only\n");
 359                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 360                 hw->phy.autoneg_advertised = PHY_ADVERTISE_10_HALF |
 361                                                 PHY_ADVERTISE_10_FULL;
 362                 hw->mac.link_speed = SPEED_10;
 363                 hw->mac.link_duplex = DUPLEX_HALF;
 364                 break;
 365         case SPEED_10 + HALF_DUPLEX:
 366                 netdev_dbg(adapter->netdev, "Forcing to 10 Mbps Half Duplex\n");
 367                 hw->mac.autoneg = hw->mac.fc_autoneg = 0;
 368                 hw->phy.autoneg_advertised = 0;
 369                 hw->mac.link_speed = SPEED_10;
 370                 hw->mac.link_duplex = DUPLEX_HALF;
 371                 break;
 372         case SPEED_10 + FULL_DUPLEX:
 373                 netdev_dbg(adapter->netdev, "Forcing to 10 Mbps Full Duplex\n");
 374                 hw->mac.autoneg = hw->mac.fc_autoneg = 0;
 375                 hw->phy.autoneg_advertised = 0;
 376                 hw->mac.link_speed = SPEED_10;
 377                 hw->mac.link_duplex = DUPLEX_FULL;
 378                 break;
 379         case SPEED_100:
 380                 netdev_dbg(adapter->netdev,
 381                            "100 Mbps Speed specified without Duplex\n");
 382                 netdev_dbg(adapter->netdev,
 383                            "Using Autonegotiation at 100 Mbps only\n");
 384                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 385                 hw->phy.autoneg_advertised = PHY_ADVERTISE_100_HALF |
 386                                                 PHY_ADVERTISE_100_FULL;
 387                 hw->mac.link_speed = SPEED_100;
 388                 hw->mac.link_duplex = DUPLEX_HALF;
 389                 break;
 390         case SPEED_100 + HALF_DUPLEX:
 391                 netdev_dbg(adapter->netdev,
 392                            "Forcing to 100 Mbps Half Duplex\n");
 393                 hw->mac.autoneg = hw->mac.fc_autoneg = 0;
 394                 hw->phy.autoneg_advertised = 0;
 395                 hw->mac.link_speed = SPEED_100;
 396                 hw->mac.link_duplex = DUPLEX_HALF;
 397                 break;
 398         case SPEED_100 + FULL_DUPLEX:
 399                 netdev_dbg(adapter->netdev,
 400                            "Forcing to 100 Mbps Full Duplex\n");
 401                 hw->mac.autoneg = hw->mac.fc_autoneg = 0;
 402                 hw->phy.autoneg_advertised = 0;
 403                 hw->mac.link_speed = SPEED_100;
 404                 hw->mac.link_duplex = DUPLEX_FULL;
 405                 break;
 406         case SPEED_1000:
 407                 netdev_dbg(adapter->netdev,
 408                            "1000 Mbps Speed specified without Duplex\n");
 409                 goto full_duplex_only;
 410         case SPEED_1000 + HALF_DUPLEX:
 411                 netdev_dbg(adapter->netdev,
 412                            "Half Duplex is not supported at 1000 Mbps\n");
 413                 /* fall through */
 414         case SPEED_1000 + FULL_DUPLEX:
 415 full_duplex_only:
 416                 netdev_dbg(adapter->netdev,
 417                            "Using Autonegotiation at 1000 Mbps Full Duplex only\n");
 418                 hw->mac.autoneg = hw->mac.fc_autoneg = 1;
 419                 hw->phy.autoneg_advertised = PHY_ADVERTISE_1000_FULL;
 420                 hw->mac.link_speed = SPEED_1000;
 421                 hw->mac.link_duplex = DUPLEX_FULL;
 422                 break;
 423         default:
 424                 BUG();
 425         }
 426 }
 427 
 428 /**
 429  * pch_gbe_check_options - Range Checking for Command Line Parameters
 430  * @adapter:  Board private structure
 431  */
 432 void pch_gbe_check_options(struct pch_gbe_adapter *adapter)
 433 {
 434         struct pch_gbe_hw *hw = &adapter->hw;
 435         struct net_device *dev = adapter->netdev;
 436         int val;
 437 
 438         { /* Transmit Descriptor Count */
 439                 static const struct pch_gbe_option opt = {
 440                         .type = range_option,
 441                         .name = "Transmit Descriptors",
 442                         .err  = "using default of "
 443                                 __MODULE_STRING(PCH_GBE_DEFAULT_TXD),
 444                         .def  = PCH_GBE_DEFAULT_TXD,
 445                         .arg  = { .r = { .min = PCH_GBE_MIN_TXD,
 446                                          .max = PCH_GBE_MAX_TXD } }
 447                 };
 448                 struct pch_gbe_tx_ring *tx_ring = adapter->tx_ring;
 449                 tx_ring->count = TxDescriptors;
 450                 pch_gbe_validate_option(&tx_ring->count, &opt, adapter);
 451                 tx_ring->count = roundup(tx_ring->count,
 452                                         PCH_GBE_TX_DESC_MULTIPLE);
 453         }
 454         { /* Receive Descriptor Count */
 455                 static const struct pch_gbe_option opt = {
 456                         .type = range_option,
 457                         .name = "Receive Descriptors",
 458                         .err  = "using default of "
 459                                 __MODULE_STRING(PCH_GBE_DEFAULT_RXD),
 460                         .def  = PCH_GBE_DEFAULT_RXD,
 461                         .arg  = { .r = { .min = PCH_GBE_MIN_RXD,
 462                                          .max = PCH_GBE_MAX_RXD } }
 463                 };
 464                 struct pch_gbe_rx_ring *rx_ring = adapter->rx_ring;
 465                 rx_ring->count = RxDescriptors;
 466                 pch_gbe_validate_option(&rx_ring->count, &opt, adapter);
 467                 rx_ring->count = roundup(rx_ring->count,
 468                                 PCH_GBE_RX_DESC_MULTIPLE);
 469         }
 470         { /* Checksum Offload Enable/Disable */
 471                 static const struct pch_gbe_option opt = {
 472                         .type = enable_option,
 473                         .name = "Checksum Offload",
 474                         .err  = "defaulting to Enabled",
 475                         .def  = PCH_GBE_DEFAULT_RX_CSUM
 476                 };
 477                 val = XsumRX;
 478                 pch_gbe_validate_option(&val, &opt, adapter);
 479                 if (!val)
 480                         dev->features &= ~NETIF_F_RXCSUM;
 481         }
 482         { /* Checksum Offload Enable/Disable */
 483                 static const struct pch_gbe_option opt = {
 484                         .type = enable_option,
 485                         .name = "Checksum Offload",
 486                         .err  = "defaulting to Enabled",
 487                         .def  = PCH_GBE_DEFAULT_TX_CSUM
 488                 };
 489                 val = XsumTX;
 490                 pch_gbe_validate_option(&val, &opt, adapter);
 491                 if (!val)
 492                         dev->features &= ~NETIF_F_CSUM_MASK;
 493         }
 494         { /* Flow Control */
 495                 static const struct pch_gbe_option opt = {
 496                         .type = list_option,
 497                         .name = "Flow Control",
 498                         .err  = "reading default settings from EEPROM",
 499                         .def  = PCH_GBE_FC_DEFAULT,
 500                         .arg  = { .l = { .nr = (int)ARRAY_SIZE(fc_list),
 501                                          .p = fc_list } }
 502                 };
 503                 int tmp = FlowControl;
 504 
 505                 pch_gbe_validate_option(&tmp, &opt, adapter);
 506                 hw->mac.fc = tmp;
 507         }
 508 
 509         pch_gbe_check_copper_options(adapter);
 510 }
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_param.c

DEFINITIONS
