root/drivers/net/wireless/admtek/adm8211.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. adm8211_eeprom_register_read
  2. adm8211_eeprom_register_write
  3. adm8211_read_eeprom
  4. adm8211_write_sram
  5. adm8211_write_sram_bytes
  6. adm8211_clear_sram
  7. adm8211_get_stats
  8. adm8211_interrupt_tci
  9. adm8211_interrupt_rci
  10. adm8211_interrupt
  11. WRITE_SYN
  12. adm8211_rf_set_channel
  13. adm8211_update_mode
  14. adm8211_hw_init_syn
  15. adm8211_hw_init_bbp
  16. adm8211_set_rate
  17. adm8211_hw_init
  18. adm8211_hw_reset
  19. adm8211_get_tsft
  20. adm8211_set_interval
  21. adm8211_set_bssid
  22. adm8211_config
  23. adm8211_bss_info_changed
  24. adm8211_prepare_multicast
  25. adm8211_configure_filter
  26. adm8211_add_interface
  27. adm8211_remove_interface
  28. adm8211_init_rings
  29. adm8211_free_rings
  30. adm8211_start
  31. adm8211_stop
  32. adm8211_calc_durations
  33. adm8211_tx_raw
  34. adm8211_tx
  35. adm8211_alloc_rings
  36. adm8211_probe
  37. adm8211_remove
  38. adm8211_suspend
  39. adm8211_resume

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 
   3 /*
   4  * Linux device driver for ADMtek ADM8211 (IEEE 802.11b MAC/BBP)
   5  *
   6  * Copyright (c) 2003, Jouni Malinen <j@w1.fi>
   7  * Copyright (c) 2004-2007, Michael Wu <flamingice@sourmilk.net>
   8  * Some parts copyright (c) 2003 by David Young <dyoung@pobox.com>
   9  * and used with permission.
  10  *
  11  * Much thanks to Infineon-ADMtek for their support of this driver.
  12  */
  13 
  14 #include <linux/interrupt.h>
  15 #include <linux/if.h>
  16 #include <linux/skbuff.h>
  17 #include <linux/slab.h>
  18 #include <linux/etherdevice.h>
  19 #include <linux/pci.h>
  20 #include <linux/delay.h>
  21 #include <linux/crc32.h>
  22 #include <linux/eeprom_93cx6.h>
  23 #include <linux/module.h>
  24 #include <net/mac80211.h>
  25 
  26 #include "adm8211.h"
  27 
  28 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
  29 MODULE_AUTHOR("Jouni Malinen <j@w1.fi>");
  30 MODULE_DESCRIPTION("Driver for IEEE 802.11b wireless cards based on ADMtek ADM8211");
  31 MODULE_SUPPORTED_DEVICE("ADM8211");
  32 MODULE_LICENSE("GPL");
  33 
  34 static unsigned int tx_ring_size __read_mostly = 16;
  35 static unsigned int rx_ring_size __read_mostly = 16;
  36 
  37 module_param(tx_ring_size, uint, 0);
  38 module_param(rx_ring_size, uint, 0);
  39 
  40 static const struct pci_device_id adm8211_pci_id_table[] = {
  41         /* ADMtek ADM8211 */
  42         { PCI_DEVICE(0x10B7, 0x6000) }, /* 3Com 3CRSHPW796 */
  43         { PCI_DEVICE(0x1200, 0x8201) }, /* ? */
  44         { PCI_DEVICE(0x1317, 0x8201) }, /* ADM8211A */
  45         { PCI_DEVICE(0x1317, 0x8211) }, /* ADM8211B/C */
  46         { 0 }
  47 };
  48 
  49 static struct ieee80211_rate adm8211_rates[] = {
  50         { .bitrate = 10, .flags = IEEE80211_RATE_SHORT_PREAMBLE },
  51         { .bitrate = 20, .flags = IEEE80211_RATE_SHORT_PREAMBLE },
  52         { .bitrate = 55, .flags = IEEE80211_RATE_SHORT_PREAMBLE },
  53         { .bitrate = 110, .flags = IEEE80211_RATE_SHORT_PREAMBLE },
  54         { .bitrate = 220, .flags = IEEE80211_RATE_SHORT_PREAMBLE }, /* XX ?? */
  55 };
  56 
  57 static const struct ieee80211_channel adm8211_channels[] = {
  58         { .center_freq = 2412},
  59         { .center_freq = 2417},
  60         { .center_freq = 2422},
  61         { .center_freq = 2427},
  62         { .center_freq = 2432},
  63         { .center_freq = 2437},
  64         { .center_freq = 2442},
  65         { .center_freq = 2447},
  66         { .center_freq = 2452},
  67         { .center_freq = 2457},
  68         { .center_freq = 2462},
  69         { .center_freq = 2467},
  70         { .center_freq = 2472},
  71         { .center_freq = 2484},
  72 };
  73 
  74 
  75 static void adm8211_eeprom_register_read(struct eeprom_93cx6 *eeprom)
  76 {
  77         struct adm8211_priv *priv = eeprom->data;
  78         u32 reg = ADM8211_CSR_READ(SPR);
  79 
  80         eeprom->reg_data_in = reg & ADM8211_SPR_SDI;
  81         eeprom->reg_data_out = reg & ADM8211_SPR_SDO;
  82         eeprom->reg_data_clock = reg & ADM8211_SPR_SCLK;
  83         eeprom->reg_chip_select = reg & ADM8211_SPR_SCS;
  84 }
  85 
  86 static void adm8211_eeprom_register_write(struct eeprom_93cx6 *eeprom)
  87 {
  88         struct adm8211_priv *priv = eeprom->data;
  89         u32 reg = 0x4000 | ADM8211_SPR_SRS;
  90 
  91         if (eeprom->reg_data_in)
  92                 reg |= ADM8211_SPR_SDI;
  93         if (eeprom->reg_data_out)
  94                 reg |= ADM8211_SPR_SDO;
  95         if (eeprom->reg_data_clock)
  96                 reg |= ADM8211_SPR_SCLK;
  97         if (eeprom->reg_chip_select)
  98                 reg |= ADM8211_SPR_SCS;
  99 
 100         ADM8211_CSR_WRITE(SPR, reg);
 101         ADM8211_CSR_READ(SPR);          /* eeprom_delay */
 102 }
 103 
 104 static int adm8211_read_eeprom(struct ieee80211_hw *dev)
 105 {
 106         struct adm8211_priv *priv = dev->priv;
 107         unsigned int words, i;
 108         struct ieee80211_chan_range chan_range;
 109         u16 cr49;
 110         struct eeprom_93cx6 eeprom = {
 111                 .data           = priv,
 112                 .register_read  = adm8211_eeprom_register_read,
 113                 .register_write = adm8211_eeprom_register_write
 114         };
 115 
 116         if (ADM8211_CSR_READ(CSR_TEST0) & ADM8211_CSR_TEST0_EPTYP) {
 117                 /* 256 * 16-bit = 512 bytes */
 118                 eeprom.width = PCI_EEPROM_WIDTH_93C66;
 119                 words = 256;
 120         } else {
 121                 /* 64 * 16-bit = 128 bytes */
 122                 eeprom.width = PCI_EEPROM_WIDTH_93C46;
 123                 words = 64;
 124         }
 125 
 126         priv->eeprom_len = words * 2;
 127         priv->eeprom = kmalloc(priv->eeprom_len, GFP_KERNEL);
 128         if (!priv->eeprom)
 129                 return -ENOMEM;
 130 
 131         eeprom_93cx6_multiread(&eeprom, 0, (__le16 *)priv->eeprom, words);
 132 
 133         cr49 = le16_to_cpu(priv->eeprom->cr49);
 134         priv->rf_type = (cr49 >> 3) & 0x7;
 135         switch (priv->rf_type) {
 136         case ADM8211_TYPE_INTERSIL:
 137         case ADM8211_TYPE_RFMD:
 138         case ADM8211_TYPE_MARVEL:
 139         case ADM8211_TYPE_AIROHA:
 140         case ADM8211_TYPE_ADMTEK:
 141                 break;
 142 
 143         default:
 144                 if (priv->pdev->revision < ADM8211_REV_CA)
 145                         priv->rf_type = ADM8211_TYPE_RFMD;
 146                 else
 147                         priv->rf_type = ADM8211_TYPE_AIROHA;
 148 
 149                 printk(KERN_WARNING "%s (adm8211): Unknown RFtype %d\n",
 150                        pci_name(priv->pdev), (cr49 >> 3) & 0x7);
 151         }
 152 
 153         priv->bbp_type = cr49 & 0x7;
 154         switch (priv->bbp_type) {
 155         case ADM8211_TYPE_INTERSIL:
 156         case ADM8211_TYPE_RFMD:
 157         case ADM8211_TYPE_MARVEL:
 158         case ADM8211_TYPE_AIROHA:
 159         case ADM8211_TYPE_ADMTEK:
 160                 break;
 161         default:
 162                 if (priv->pdev->revision < ADM8211_REV_CA)
 163                         priv->bbp_type = ADM8211_TYPE_RFMD;
 164                 else
 165                         priv->bbp_type = ADM8211_TYPE_ADMTEK;
 166 
 167                 printk(KERN_WARNING "%s (adm8211): Unknown BBPtype: %d\n",
 168                        pci_name(priv->pdev), cr49 >> 3);
 169         }
 170 
 171         if (priv->eeprom->country_code >= ARRAY_SIZE(cranges)) {
 172                 printk(KERN_WARNING "%s (adm8211): Invalid country code (%d)\n",
 173                        pci_name(priv->pdev), priv->eeprom->country_code);
 174 
 175                 chan_range = cranges[2];
 176         } else
 177                 chan_range = cranges[priv->eeprom->country_code];
 178 
 179         printk(KERN_DEBUG "%s (adm8211): Channel range: %d - %d\n",
 180                pci_name(priv->pdev), (int)chan_range.min, (int)chan_range.max);
 181 
 182         BUILD_BUG_ON(sizeof(priv->channels) != sizeof(adm8211_channels));
 183 
 184         memcpy(priv->channels, adm8211_channels, sizeof(priv->channels));
 185         priv->band.channels = priv->channels;
 186         priv->band.n_channels = ARRAY_SIZE(adm8211_channels);
 187         priv->band.bitrates = adm8211_rates;
 188         priv->band.n_bitrates = ARRAY_SIZE(adm8211_rates);
 189 
 190         for (i = 1; i <= ARRAY_SIZE(adm8211_channels); i++)
 191                 if (i < chan_range.min || i > chan_range.max)
 192                         priv->channels[i - 1].flags |= IEEE80211_CHAN_DISABLED;
 193 
 194         switch (priv->eeprom->specific_bbptype) {
 195         case ADM8211_BBP_RFMD3000:
 196         case ADM8211_BBP_RFMD3002:
 197         case ADM8211_BBP_ADM8011:
 198                 priv->specific_bbptype = priv->eeprom->specific_bbptype;
 199                 break;
 200 
 201         default:
 202                 if (priv->pdev->revision < ADM8211_REV_CA)
 203                         priv->specific_bbptype = ADM8211_BBP_RFMD3000;
 204                 else
 205                         priv->specific_bbptype = ADM8211_BBP_ADM8011;
 206 
 207                 printk(KERN_WARNING "%s (adm8211): Unknown specific BBP: %d\n",
 208                        pci_name(priv->pdev), priv->eeprom->specific_bbptype);
 209         }
 210 
 211         switch (priv->eeprom->specific_rftype) {
 212         case ADM8211_RFMD2948:
 213         case ADM8211_RFMD2958:
 214         case ADM8211_RFMD2958_RF3000_CONTROL_POWER:
 215         case ADM8211_MAX2820:
 216         case ADM8211_AL2210L:
 217                 priv->transceiver_type = priv->eeprom->specific_rftype;
 218                 break;
 219 
 220         default:
 221                 if (priv->pdev->revision == ADM8211_REV_BA)
 222                         priv->transceiver_type = ADM8211_RFMD2958_RF3000_CONTROL_POWER;
 223                 else if (priv->pdev->revision == ADM8211_REV_CA)
 224                         priv->transceiver_type = ADM8211_AL2210L;
 225                 else if (priv->pdev->revision == ADM8211_REV_AB)
 226                         priv->transceiver_type = ADM8211_RFMD2948;
 227 
 228                 printk(KERN_WARNING "%s (adm8211): Unknown transceiver: %d\n",
 229                        pci_name(priv->pdev), priv->eeprom->specific_rftype);
 230 
 231                 break;
 232         }
 233 
 234         printk(KERN_DEBUG "%s (adm8211): RFtype=%d BBPtype=%d Specific BBP=%d "
 235                "Transceiver=%d\n", pci_name(priv->pdev), priv->rf_type,
 236                priv->bbp_type, priv->specific_bbptype, priv->transceiver_type);
 237 
 238         return 0;
 239 }
 240 
 241 static inline void adm8211_write_sram(struct ieee80211_hw *dev,
 242                                       u32 addr, u32 data)
 243 {
 244         struct adm8211_priv *priv = dev->priv;
 245 
 246         ADM8211_CSR_WRITE(WEPCTL, addr | ADM8211_WEPCTL_TABLE_WR |
 247                           (priv->pdev->revision < ADM8211_REV_BA ?
 248                            0 : ADM8211_WEPCTL_SEL_WEPTABLE ));
 249         ADM8211_CSR_READ(WEPCTL);
 250         msleep(1);
 251 
 252         ADM8211_CSR_WRITE(WESK, data);
 253         ADM8211_CSR_READ(WESK);
 254         msleep(1);
 255 }
 256 
 257 static void adm8211_write_sram_bytes(struct ieee80211_hw *dev,
 258                                      unsigned int addr, u8 *buf,
 259                                      unsigned int len)
 260 {
 261         struct adm8211_priv *priv = dev->priv;
 262         u32 reg = ADM8211_CSR_READ(WEPCTL);
 263         unsigned int i;
 264 
 265         if (priv->pdev->revision < ADM8211_REV_BA) {
 266                 for (i = 0; i < len; i += 2) {
 267                         u16 val = buf[i] | (buf[i + 1] << 8);
 268                         adm8211_write_sram(dev, addr + i / 2, val);
 269                 }
 270         } else {
 271                 for (i = 0; i < len; i += 4) {
 272                         u32 val = (buf[i + 0] << 0 ) | (buf[i + 1] << 8 ) |
 273                                   (buf[i + 2] << 16) | (buf[i + 3] << 24);
 274                         adm8211_write_sram(dev, addr + i / 4, val);
 275                 }
 276         }
 277 
 278         ADM8211_CSR_WRITE(WEPCTL, reg);
 279 }
 280 
 281 static void adm8211_clear_sram(struct ieee80211_hw *dev)
 282 {
 283         struct adm8211_priv *priv = dev->priv;
 284         u32 reg = ADM8211_CSR_READ(WEPCTL);
 285         unsigned int addr;
 286 
 287         for (addr = 0; addr < ADM8211_SRAM_SIZE; addr++)
 288                 adm8211_write_sram(dev, addr, 0);
 289 
 290         ADM8211_CSR_WRITE(WEPCTL, reg);
 291 }
 292 
 293 static int adm8211_get_stats(struct ieee80211_hw *dev,
 294                              struct ieee80211_low_level_stats *stats)
 295 {
 296         struct adm8211_priv *priv = dev->priv;
 297 
 298         memcpy(stats, &priv->stats, sizeof(*stats));
 299 
 300         return 0;
 301 }
 302 
 303 static void adm8211_interrupt_tci(struct ieee80211_hw *dev)
 304 {
 305         struct adm8211_priv *priv = dev->priv;
 306         unsigned int dirty_tx;
 307 
 308         spin_lock(&priv->lock);
 309 
 310         for (dirty_tx = priv->dirty_tx; priv->cur_tx - dirty_tx; dirty_tx++) {
 311                 unsigned int entry = dirty_tx % priv->tx_ring_size;
 312                 u32 status = le32_to_cpu(priv->tx_ring[entry].status);
 313                 struct ieee80211_tx_info *txi;
 314                 struct adm8211_tx_ring_info *info;
 315                 struct sk_buff *skb;
 316 
 317                 if (status & TDES0_CONTROL_OWN ||
 318                     !(status & TDES0_CONTROL_DONE))
 319                         break;
 320 
 321                 info = &priv->tx_buffers[entry];
 322                 skb = info->skb;
 323                 txi = IEEE80211_SKB_CB(skb);
 324 
 325                 /* TODO: check TDES0_STATUS_TUF and TDES0_STATUS_TRO */
 326 
 327                 pci_unmap_single(priv->pdev, info->mapping,
 328                                  info->skb->len, PCI_DMA_TODEVICE);
 329 
 330                 ieee80211_tx_info_clear_status(txi);
 331 
 332                 skb_pull(skb, sizeof(struct adm8211_tx_hdr));
 333                 memcpy(skb_push(skb, info->hdrlen), skb->cb, info->hdrlen);
 334                 if (!(txi->flags & IEEE80211_TX_CTL_NO_ACK) &&
 335                     !(status & TDES0_STATUS_ES))
 336                         txi->flags |= IEEE80211_TX_STAT_ACK;
 337 
 338                 ieee80211_tx_status_irqsafe(dev, skb);
 339 
 340                 info->skb = NULL;
 341         }
 342 
 343         if (priv->cur_tx - dirty_tx < priv->tx_ring_size - 2)
 344                 ieee80211_wake_queue(dev, 0);
 345 
 346         priv->dirty_tx = dirty_tx;
 347         spin_unlock(&priv->lock);
 348 }
 349 
 350 
 351 static void adm8211_interrupt_rci(struct ieee80211_hw *dev)
 352 {
 353         struct adm8211_priv *priv = dev->priv;
 354         unsigned int entry = priv->cur_rx % priv->rx_ring_size;
 355         u32 status;
 356         unsigned int pktlen;
 357         struct sk_buff *skb, *newskb;
 358         unsigned int limit = priv->rx_ring_size;
 359         u8 rssi, rate;
 360 
 361         while (!(priv->rx_ring[entry].status & cpu_to_le32(RDES0_STATUS_OWN))) {
 362                 if (!limit--)
 363                         break;
 364 
 365                 status = le32_to_cpu(priv->rx_ring[entry].status);
 366                 rate = (status & RDES0_STATUS_RXDR) >> 12;
 367                 rssi = le32_to_cpu(priv->rx_ring[entry].length) &
 368                         RDES1_STATUS_RSSI;
 369 
 370                 pktlen = status & RDES0_STATUS_FL;
 371                 if (pktlen > RX_PKT_SIZE) {
 372                         if (net_ratelimit())
 373                                 wiphy_debug(dev->wiphy, "frame too long (%d)\n",
 374                                             pktlen);
 375                         pktlen = RX_PKT_SIZE;
 376                 }
 377 
 378                 if (!priv->soft_rx_crc && status & RDES0_STATUS_ES) {
 379                         skb = NULL; /* old buffer will be reused */
 380                         /* TODO: update RX error stats */
 381                         /* TODO: check RDES0_STATUS_CRC*E */
 382                 } else if (pktlen < RX_COPY_BREAK) {
 383                         skb = dev_alloc_skb(pktlen);
 384                         if (skb) {
 385                                 pci_dma_sync_single_for_cpu(
 386                                         priv->pdev,
 387                                         priv->rx_buffers[entry].mapping,
 388                                         pktlen, PCI_DMA_FROMDEVICE);
 389                                 skb_put_data(skb,
 390                                              skb_tail_pointer(priv->rx_buffers[entry].skb),
 391                                              pktlen);
 392                                 pci_dma_sync_single_for_device(
 393                                         priv->pdev,
 394                                         priv->rx_buffers[entry].mapping,
 395                                         RX_PKT_SIZE, PCI_DMA_FROMDEVICE);
 396                         }
 397                 } else {
 398                         newskb = dev_alloc_skb(RX_PKT_SIZE);
 399                         if (newskb) {
 400                                 skb = priv->rx_buffers[entry].skb;
 401                                 skb_put(skb, pktlen);
 402                                 pci_unmap_single(
 403                                         priv->pdev,
 404                                         priv->rx_buffers[entry].mapping,
 405                                         RX_PKT_SIZE, PCI_DMA_FROMDEVICE);
 406                                 priv->rx_buffers[entry].skb = newskb;
 407                                 priv->rx_buffers[entry].mapping =
 408                                         pci_map_single(priv->pdev,
 409                                                        skb_tail_pointer(newskb),
 410                                                        RX_PKT_SIZE,
 411                                                        PCI_DMA_FROMDEVICE);
 412                                 if (pci_dma_mapping_error(priv->pdev,
 413                                            priv->rx_buffers[entry].mapping)) {
 414                                         priv->rx_buffers[entry].skb = NULL;
 415                                         dev_kfree_skb(newskb);
 416                                         skb = NULL;
 417                                         /* TODO: update rx dropped stats */
 418                                 }
 419                         } else {
 420                                 skb = NULL;
 421                                 /* TODO: update rx dropped stats */
 422                         }
 423 
 424                         priv->rx_ring[entry].buffer1 =
 425                                 cpu_to_le32(priv->rx_buffers[entry].mapping);
 426                 }
 427 
 428                 priv->rx_ring[entry].status = cpu_to_le32(RDES0_STATUS_OWN |
 429                                                           RDES0_STATUS_SQL);
 430                 priv->rx_ring[entry].length =
 431                         cpu_to_le32(RX_PKT_SIZE |
 432                                     (entry == priv->rx_ring_size - 1 ?
 433                                      RDES1_CONTROL_RER : 0));
 434 
 435                 if (skb) {
 436                         struct ieee80211_rx_status rx_status = {0};
 437 
 438                         if (priv->pdev->revision < ADM8211_REV_CA)
 439                                 rx_status.signal = rssi;
 440                         else
 441                                 rx_status.signal = 100 - rssi;
 442 
 443                         rx_status.rate_idx = rate;
 444 
 445                         rx_status.freq = adm8211_channels[priv->channel - 1].center_freq;
 446                         rx_status.band = NL80211_BAND_2GHZ;
 447 
 448                         memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status));
 449                         ieee80211_rx_irqsafe(dev, skb);
 450                 }
 451 
 452                 entry = (++priv->cur_rx) % priv->rx_ring_size;
 453         }
 454 
 455         /* TODO: check LPC and update stats? */
 456 }
 457 
 458 
 459 static irqreturn_t adm8211_interrupt(int irq, void *dev_id)
 460 {
 461 #define ADM8211_INT(x)                                          \
 462 do {                                                            \
 463         if (unlikely(stsr & ADM8211_STSR_ ## x))                \
 464                 wiphy_debug(dev->wiphy, "%s\n", #x);            \
 465 } while (0)
 466 
 467         struct ieee80211_hw *dev = dev_id;
 468         struct adm8211_priv *priv = dev->priv;
 469         u32 stsr = ADM8211_CSR_READ(STSR);
 470         ADM8211_CSR_WRITE(STSR, stsr);
 471         if (stsr == 0xffffffff)
 472                 return IRQ_HANDLED;
 473 
 474         if (!(stsr & (ADM8211_STSR_NISS | ADM8211_STSR_AISS)))
 475                 return IRQ_HANDLED;
 476 
 477         if (stsr & ADM8211_STSR_RCI)
 478                 adm8211_interrupt_rci(dev);
 479         if (stsr & ADM8211_STSR_TCI)
 480                 adm8211_interrupt_tci(dev);
 481 
 482         ADM8211_INT(PCF);
 483         ADM8211_INT(BCNTC);
 484         ADM8211_INT(GPINT);
 485         ADM8211_INT(ATIMTC);
 486         ADM8211_INT(TSFTF);
 487         ADM8211_INT(TSCZ);
 488         ADM8211_INT(SQL);
 489         ADM8211_INT(WEPTD);
 490         ADM8211_INT(ATIME);
 491         ADM8211_INT(TEIS);
 492         ADM8211_INT(FBE);
 493         ADM8211_INT(REIS);
 494         ADM8211_INT(GPTT);
 495         ADM8211_INT(RPS);
 496         ADM8211_INT(RDU);
 497         ADM8211_INT(TUF);
 498         ADM8211_INT(TPS);
 499 
 500         return IRQ_HANDLED;
 501 
 502 #undef ADM8211_INT
 503 }
 504 
 505 #define WRITE_SYN(name,v_mask,v_shift,a_mask,a_shift,bits,prewrite,postwrite)\
 506 static void adm8211_rf_write_syn_ ## name (struct ieee80211_hw *dev,         \
 507                                            u16 addr, u32 value) {            \
 508         struct adm8211_priv *priv = dev->priv;                               \
 509         unsigned int i;                                                      \
 510         u32 reg, bitbuf;                                                     \
 511                                                                              \
 512         value &= v_mask;                                                     \
 513         addr &= a_mask;                                                      \
 514         bitbuf = (value << v_shift) | (addr << a_shift);                     \
 515                                                                              \
 516         ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_IF_SELECT_1);                 \
 517         ADM8211_CSR_READ(SYNRF);                                             \
 518         ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_IF_SELECT_0);                 \
 519         ADM8211_CSR_READ(SYNRF);                                             \
 520                                                                              \
 521         if (prewrite) {                                                      \
 522                 ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_WRITE_SYNDATA_0);     \
 523                 ADM8211_CSR_READ(SYNRF);                                     \
 524         }                                                                    \
 525                                                                              \
 526         for (i = 0; i <= bits; i++) {                                        \
 527                 if (bitbuf & (1 << (bits - i)))                              \
 528                         reg = ADM8211_SYNRF_WRITE_SYNDATA_1;                 \
 529                 else                                                         \
 530                         reg = ADM8211_SYNRF_WRITE_SYNDATA_0;                 \
 531                                                                              \
 532                 ADM8211_CSR_WRITE(SYNRF, reg);                               \
 533                 ADM8211_CSR_READ(SYNRF);                                     \
 534                                                                              \
 535                 ADM8211_CSR_WRITE(SYNRF, reg | ADM8211_SYNRF_WRITE_CLOCK_1); \
 536                 ADM8211_CSR_READ(SYNRF);                                     \
 537                 ADM8211_CSR_WRITE(SYNRF, reg | ADM8211_SYNRF_WRITE_CLOCK_0); \
 538                 ADM8211_CSR_READ(SYNRF);                                     \
 539         }                                                                    \
 540                                                                              \
 541         if (postwrite == 1) {                                                \
 542                 ADM8211_CSR_WRITE(SYNRF, reg | ADM8211_SYNRF_IF_SELECT_0);   \
 543                 ADM8211_CSR_READ(SYNRF);                                     \
 544         }                                                                    \
 545         if (postwrite == 2) {                                                \
 546                 ADM8211_CSR_WRITE(SYNRF, reg | ADM8211_SYNRF_IF_SELECT_1);   \
 547                 ADM8211_CSR_READ(SYNRF);                                     \
 548         }                                                                    \
 549                                                                              \
 550         ADM8211_CSR_WRITE(SYNRF, 0);                                         \
 551         ADM8211_CSR_READ(SYNRF);                                             \
 552 }
 553 
 554 WRITE_SYN(max2820,  0x00FFF, 0, 0x0F, 12, 15, 1, 1)
 555 WRITE_SYN(al2210l,  0xFFFFF, 4, 0x0F,  0, 23, 1, 1)
 556 WRITE_SYN(rfmd2958, 0x3FFFF, 0, 0x1F, 18, 23, 0, 1)
 557 WRITE_SYN(rfmd2948, 0x0FFFF, 4, 0x0F,  0, 21, 0, 2)
 558 
 559 #undef WRITE_SYN
 560 
 561 static int adm8211_write_bbp(struct ieee80211_hw *dev, u8 addr, u8 data)
 562 {
 563         struct adm8211_priv *priv = dev->priv;
 564         unsigned int timeout;
 565         u32 reg;
 566 
 567         timeout = 10;
 568         while (timeout > 0) {
 569                 reg = ADM8211_CSR_READ(BBPCTL);
 570                 if (!(reg & (ADM8211_BBPCTL_WR | ADM8211_BBPCTL_RD)))
 571                         break;
 572                 timeout--;
 573                 msleep(2);
 574         }
 575 
 576         if (timeout == 0) {
 577                 wiphy_debug(dev->wiphy,
 578                             "adm8211_write_bbp(%d,%d) failed prewrite (reg=0x%08x)\n",
 579                             addr, data, reg);
 580                 return -ETIMEDOUT;
 581         }
 582 
 583         switch (priv->bbp_type) {
 584         case ADM8211_TYPE_INTERSIL:
 585                 reg = ADM8211_BBPCTL_MMISEL;    /* three wire interface */
 586                 break;
 587         case ADM8211_TYPE_RFMD:
 588                 reg = (0x20 << 24) | ADM8211_BBPCTL_TXCE | ADM8211_BBPCTL_CCAP |
 589                       (0x01 << 18);
 590                 break;
 591         case ADM8211_TYPE_ADMTEK:
 592                 reg = (0x20 << 24) | ADM8211_BBPCTL_TXCE | ADM8211_BBPCTL_CCAP |
 593                       (0x05 << 18);
 594                 break;
 595         }
 596         reg |= ADM8211_BBPCTL_WR | (addr << 8) | data;
 597 
 598         ADM8211_CSR_WRITE(BBPCTL, reg);
 599 
 600         timeout = 10;
 601         while (timeout > 0) {
 602                 reg = ADM8211_CSR_READ(BBPCTL);
 603                 if (!(reg & ADM8211_BBPCTL_WR))
 604                         break;
 605                 timeout--;
 606                 msleep(2);
 607         }
 608 
 609         if (timeout == 0) {
 610                 ADM8211_CSR_WRITE(BBPCTL, ADM8211_CSR_READ(BBPCTL) &
 611                                   ~ADM8211_BBPCTL_WR);
 612                 wiphy_debug(dev->wiphy,
 613                             "adm8211_write_bbp(%d,%d) failed postwrite (reg=0x%08x)\n",
 614                             addr, data, reg);
 615                 return -ETIMEDOUT;
 616         }
 617 
 618         return 0;
 619 }
 620 
 621 static int adm8211_rf_set_channel(struct ieee80211_hw *dev, unsigned int chan)
 622 {
 623         static const u32 adm8211_rfmd2958_reg5[] =
 624                 {0x22BD, 0x22D2, 0x22E8, 0x22FE, 0x2314, 0x232A, 0x2340,
 625                  0x2355, 0x236B, 0x2381, 0x2397, 0x23AD, 0x23C2, 0x23F7};
 626         static const u32 adm8211_rfmd2958_reg6[] =
 627                 {0x05D17, 0x3A2E8, 0x2E8BA, 0x22E8B, 0x1745D, 0x0BA2E, 0x00000,
 628                  0x345D1, 0x28BA2, 0x1D174, 0x11745, 0x05D17, 0x3A2E8, 0x11745};
 629 
 630         struct adm8211_priv *priv = dev->priv;
 631         u8 ant_power = priv->ant_power > 0x3F ?
 632                 priv->eeprom->antenna_power[chan - 1] : priv->ant_power;
 633         u8 tx_power = priv->tx_power > 0x3F ?
 634                 priv->eeprom->tx_power[chan - 1] : priv->tx_power;
 635         u8 lpf_cutoff = priv->lpf_cutoff == 0xFF ?
 636                 priv->eeprom->lpf_cutoff[chan - 1] : priv->lpf_cutoff;
 637         u8 lnags_thresh = priv->lnags_threshold == 0xFF ?
 638                 priv->eeprom->lnags_threshold[chan - 1] : priv->lnags_threshold;
 639         u32 reg;
 640 
 641         ADM8211_IDLE();
 642 
 643         /* Program synthesizer to new channel */
 644         switch (priv->transceiver_type) {
 645         case ADM8211_RFMD2958:
 646         case ADM8211_RFMD2958_RF3000_CONTROL_POWER:
 647                 adm8211_rf_write_syn_rfmd2958(dev, 0x00, 0x04007);
 648                 adm8211_rf_write_syn_rfmd2958(dev, 0x02, 0x00033);
 649 
 650                 adm8211_rf_write_syn_rfmd2958(dev, 0x05,
 651                         adm8211_rfmd2958_reg5[chan - 1]);
 652                 adm8211_rf_write_syn_rfmd2958(dev, 0x06,
 653                         adm8211_rfmd2958_reg6[chan - 1]);
 654                 break;
 655 
 656         case ADM8211_RFMD2948:
 657                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_MAIN_CONF,
 658                                               SI4126_MAIN_XINDIV2);
 659                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_POWERDOWN,
 660                                               SI4126_POWERDOWN_PDIB |
 661                                               SI4126_POWERDOWN_PDRB);
 662                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_PHASE_DET_GAIN, 0);
 663                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_RF2_N_DIV,
 664                                               (chan == 14 ?
 665                                                2110 : (2033 + (chan * 5))));
 666                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_IF_N_DIV, 1496);
 667                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_RF2_R_DIV, 44);
 668                 adm8211_rf_write_syn_rfmd2948(dev, SI4126_IF_R_DIV, 44);
 669                 break;
 670 
 671         case ADM8211_MAX2820:
 672                 adm8211_rf_write_syn_max2820(dev, 0x3,
 673                         (chan == 14 ? 0x054 : (0x7 + (chan * 5))));
 674                 break;
 675 
 676         case ADM8211_AL2210L:
 677                 adm8211_rf_write_syn_al2210l(dev, 0x0,
 678                         (chan == 14 ? 0x229B4 : (0x22967 + (chan * 5))));
 679                 break;
 680 
 681         default:
 682                 wiphy_debug(dev->wiphy, "unsupported transceiver type %d\n",
 683                             priv->transceiver_type);
 684                 break;
 685         }
 686 
 687         /* write BBP regs */
 688         if (priv->bbp_type == ADM8211_TYPE_RFMD) {
 689 
 690         /* SMC 2635W specific? adm8211b doesn't use the 2948 though.. */
 691         /* TODO: remove if SMC 2635W doesn't need this */
 692         if (priv->transceiver_type == ADM8211_RFMD2948) {
 693                 reg = ADM8211_CSR_READ(GPIO);
 694                 reg &= 0xfffc0000;
 695                 reg |= ADM8211_CSR_GPIO_EN0;
 696                 if (chan != 14)
 697                         reg |= ADM8211_CSR_GPIO_O0;
 698                 ADM8211_CSR_WRITE(GPIO, reg);
 699         }
 700 
 701         if (priv->transceiver_type == ADM8211_RFMD2958) {
 702                 /* set PCNT2 */
 703                 adm8211_rf_write_syn_rfmd2958(dev, 0x0B, 0x07100);
 704                 /* set PCNT1 P_DESIRED/MID_BIAS */
 705                 reg = le16_to_cpu(priv->eeprom->cr49);
 706                 reg >>= 13;
 707                 reg <<= 15;
 708                 reg |= ant_power << 9;
 709                 adm8211_rf_write_syn_rfmd2958(dev, 0x0A, reg);
 710                 /* set TXRX TX_GAIN */
 711                 adm8211_rf_write_syn_rfmd2958(dev, 0x09, 0x00050 |
 712                         (priv->pdev->revision < ADM8211_REV_CA ? tx_power : 0));
 713         } else {
 714                 reg = ADM8211_CSR_READ(PLCPHD);
 715                 reg &= 0xff00ffff;
 716                 reg |= tx_power << 18;
 717                 ADM8211_CSR_WRITE(PLCPHD, reg);
 718         }
 719 
 720         ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_SELRF |
 721                           ADM8211_SYNRF_PE1 | ADM8211_SYNRF_PHYRST);
 722         ADM8211_CSR_READ(SYNRF);
 723         msleep(30);
 724 
 725         /* RF3000 BBP */
 726         if (priv->transceiver_type != ADM8211_RFMD2958)
 727                 adm8211_write_bbp(dev, RF3000_TX_VAR_GAIN__TX_LEN_EXT,
 728                                   tx_power<<2);
 729         adm8211_write_bbp(dev, RF3000_LOW_GAIN_CALIB, lpf_cutoff);
 730         adm8211_write_bbp(dev, RF3000_HIGH_GAIN_CALIB, lnags_thresh);
 731         adm8211_write_bbp(dev, 0x1c, priv->pdev->revision == ADM8211_REV_BA ?
 732                                      priv->eeprom->cr28 : 0);
 733         adm8211_write_bbp(dev, 0x1d, priv->eeprom->cr29);
 734 
 735         ADM8211_CSR_WRITE(SYNRF, 0);
 736 
 737         /* Nothing to do for ADMtek BBP */
 738         } else if (priv->bbp_type != ADM8211_TYPE_ADMTEK)
 739                 wiphy_debug(dev->wiphy, "unsupported BBP type %d\n",
 740                             priv->bbp_type);
 741 
 742         ADM8211_RESTORE();
 743 
 744         /* update current channel for adhoc (and maybe AP mode) */
 745         reg = ADM8211_CSR_READ(CAP0);
 746         reg &= ~0xF;
 747         reg |= chan;
 748         ADM8211_CSR_WRITE(CAP0, reg);
 749 
 750         return 0;
 751 }
 752 
 753 static void adm8211_update_mode(struct ieee80211_hw *dev)
 754 {
 755         struct adm8211_priv *priv = dev->priv;
 756 
 757         ADM8211_IDLE();
 758 
 759         priv->soft_rx_crc = 0;
 760         switch (priv->mode) {
 761         case NL80211_IFTYPE_STATION:
 762                 priv->nar &= ~(ADM8211_NAR_PR | ADM8211_NAR_EA);
 763                 priv->nar |= ADM8211_NAR_ST | ADM8211_NAR_SR;
 764                 break;
 765         case NL80211_IFTYPE_ADHOC:
 766                 priv->nar &= ~ADM8211_NAR_PR;
 767                 priv->nar |= ADM8211_NAR_EA | ADM8211_NAR_ST | ADM8211_NAR_SR;
 768 
 769                 /* don't trust the error bits on rev 0x20 and up in adhoc */
 770                 if (priv->pdev->revision >= ADM8211_REV_BA)
 771                         priv->soft_rx_crc = 1;
 772                 break;
 773         case NL80211_IFTYPE_MONITOR:
 774                 priv->nar &= ~(ADM8211_NAR_EA | ADM8211_NAR_ST);
 775                 priv->nar |= ADM8211_NAR_PR | ADM8211_NAR_SR;
 776                 break;
 777         }
 778 
 779         ADM8211_RESTORE();
 780 }
 781 
 782 static void adm8211_hw_init_syn(struct ieee80211_hw *dev)
 783 {
 784         struct adm8211_priv *priv = dev->priv;
 785 
 786         switch (priv->transceiver_type) {
 787         case ADM8211_RFMD2958:
 788         case ADM8211_RFMD2958_RF3000_CONTROL_POWER:
 789                 /* comments taken from ADMtek vendor driver */
 790 
 791                 /* Reset RF2958 after power on */
 792                 adm8211_rf_write_syn_rfmd2958(dev, 0x1F, 0x00000);
 793                 /* Initialize RF VCO Core Bias to maximum */
 794                 adm8211_rf_write_syn_rfmd2958(dev, 0x0C, 0x3001F);
 795                 /* Initialize IF PLL */
 796                 adm8211_rf_write_syn_rfmd2958(dev, 0x01, 0x29C03);
 797                 /* Initialize IF PLL Coarse Tuning */
 798                 adm8211_rf_write_syn_rfmd2958(dev, 0x03, 0x1FF6F);
 799                 /* Initialize RF PLL */
 800                 adm8211_rf_write_syn_rfmd2958(dev, 0x04, 0x29403);
 801                 /* Initialize RF PLL Coarse Tuning */
 802                 adm8211_rf_write_syn_rfmd2958(dev, 0x07, 0x1456F);
 803                 /* Initialize TX gain and filter BW (R9) */
 804                 adm8211_rf_write_syn_rfmd2958(dev, 0x09,
 805                         (priv->transceiver_type == ADM8211_RFMD2958 ?
 806                          0x10050 : 0x00050));
 807                 /* Initialize CAL register */
 808                 adm8211_rf_write_syn_rfmd2958(dev, 0x08, 0x3FFF8);
 809                 break;
 810 
 811         case ADM8211_MAX2820:
 812                 adm8211_rf_write_syn_max2820(dev, 0x1, 0x01E);
 813                 adm8211_rf_write_syn_max2820(dev, 0x2, 0x001);
 814                 adm8211_rf_write_syn_max2820(dev, 0x3, 0x054);
 815                 adm8211_rf_write_syn_max2820(dev, 0x4, 0x310);
 816                 adm8211_rf_write_syn_max2820(dev, 0x5, 0x000);
 817                 break;
 818 
 819         case ADM8211_AL2210L:
 820                 adm8211_rf_write_syn_al2210l(dev, 0x0, 0x0196C);
 821                 adm8211_rf_write_syn_al2210l(dev, 0x1, 0x007CB);
 822                 adm8211_rf_write_syn_al2210l(dev, 0x2, 0x3582F);
 823                 adm8211_rf_write_syn_al2210l(dev, 0x3, 0x010A9);
 824                 adm8211_rf_write_syn_al2210l(dev, 0x4, 0x77280);
 825                 adm8211_rf_write_syn_al2210l(dev, 0x5, 0x45641);
 826                 adm8211_rf_write_syn_al2210l(dev, 0x6, 0xEA130);
 827                 adm8211_rf_write_syn_al2210l(dev, 0x7, 0x80000);
 828                 adm8211_rf_write_syn_al2210l(dev, 0x8, 0x7850F);
 829                 adm8211_rf_write_syn_al2210l(dev, 0x9, 0xF900C);
 830                 adm8211_rf_write_syn_al2210l(dev, 0xA, 0x00000);
 831                 adm8211_rf_write_syn_al2210l(dev, 0xB, 0x00000);
 832                 break;
 833 
 834         case ADM8211_RFMD2948:
 835         default:
 836                 break;
 837         }
 838 }
 839 
 840 static int adm8211_hw_init_bbp(struct ieee80211_hw *dev)
 841 {
 842         struct adm8211_priv *priv = dev->priv;
 843         u32 reg;
 844 
 845         /* write addresses */
 846         if (priv->bbp_type == ADM8211_TYPE_INTERSIL) {
 847                 ADM8211_CSR_WRITE(MMIWA,  0x100E0C0A);
 848                 ADM8211_CSR_WRITE(MMIRD0, 0x00007C7E);
 849                 ADM8211_CSR_WRITE(MMIRD1, 0x00100000);
 850         } else if (priv->bbp_type == ADM8211_TYPE_RFMD ||
 851                    priv->bbp_type == ADM8211_TYPE_ADMTEK) {
 852                 /* check specific BBP type */
 853                 switch (priv->specific_bbptype) {
 854                 case ADM8211_BBP_RFMD3000:
 855                 case ADM8211_BBP_RFMD3002:
 856                         ADM8211_CSR_WRITE(MMIWA,  0x00009101);
 857                         ADM8211_CSR_WRITE(MMIRD0, 0x00000301);
 858                         break;
 859 
 860                 case ADM8211_BBP_ADM8011:
 861                         ADM8211_CSR_WRITE(MMIWA,  0x00008903);
 862                         ADM8211_CSR_WRITE(MMIRD0, 0x00001716);
 863 
 864                         reg = ADM8211_CSR_READ(BBPCTL);
 865                         reg &= ~ADM8211_BBPCTL_TYPE;
 866                         reg |= 0x5 << 18;
 867                         ADM8211_CSR_WRITE(BBPCTL, reg);
 868                         break;
 869                 }
 870 
 871                 switch (priv->pdev->revision) {
 872                 case ADM8211_REV_CA:
 873                         if (priv->transceiver_type == ADM8211_RFMD2958 ||
 874                             priv->transceiver_type == ADM8211_RFMD2958_RF3000_CONTROL_POWER ||
 875                             priv->transceiver_type == ADM8211_RFMD2948)
 876                                 ADM8211_CSR_WRITE(SYNCTL, 0x1 << 22);
 877                         else if (priv->transceiver_type == ADM8211_MAX2820 ||
 878                                  priv->transceiver_type == ADM8211_AL2210L)
 879                                 ADM8211_CSR_WRITE(SYNCTL, 0x3 << 22);
 880                         break;
 881 
 882                 case ADM8211_REV_BA:
 883                         reg  = ADM8211_CSR_READ(MMIRD1);
 884                         reg &= 0x0000FFFF;
 885                         reg |= 0x7e100000;
 886                         ADM8211_CSR_WRITE(MMIRD1, reg);
 887                         break;
 888 
 889                 case ADM8211_REV_AB:
 890                 case ADM8211_REV_AF:
 891                 default:
 892                         ADM8211_CSR_WRITE(MMIRD1, 0x7e100000);
 893                         break;
 894                 }
 895 
 896                 /* For RFMD */
 897                 ADM8211_CSR_WRITE(MACTEST, 0x800);
 898         }
 899 
 900         adm8211_hw_init_syn(dev);
 901 
 902         /* Set RF Power control IF pin to PE1+PHYRST# */
 903         ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_SELRF |
 904                           ADM8211_SYNRF_PE1 | ADM8211_SYNRF_PHYRST);
 905         ADM8211_CSR_READ(SYNRF);
 906         msleep(20);
 907 
 908         /* write BBP regs */
 909         if (priv->bbp_type == ADM8211_TYPE_RFMD) {
 910                 /* RF3000 BBP */
 911                 /* another set:
 912                  * 11: c8
 913                  * 14: 14
 914                  * 15: 50 (chan 1..13; chan 14: d0)
 915                  * 1c: 00
 916                  * 1d: 84
 917                  */
 918                 adm8211_write_bbp(dev, RF3000_CCA_CTRL, 0x80);
 919                 /* antenna selection: diversity */
 920                 adm8211_write_bbp(dev, RF3000_DIVERSITY__RSSI, 0x80);
 921                 adm8211_write_bbp(dev, RF3000_TX_VAR_GAIN__TX_LEN_EXT, 0x74);
 922                 adm8211_write_bbp(dev, RF3000_LOW_GAIN_CALIB, 0x38);
 923                 adm8211_write_bbp(dev, RF3000_HIGH_GAIN_CALIB, 0x40);
 924 
 925                 if (priv->eeprom->major_version < 2) {
 926                         adm8211_write_bbp(dev, 0x1c, 0x00);
 927                         adm8211_write_bbp(dev, 0x1d, 0x80);
 928                 } else {
 929                         if (priv->pdev->revision == ADM8211_REV_BA)
 930                                 adm8211_write_bbp(dev, 0x1c, priv->eeprom->cr28);
 931                         else
 932                                 adm8211_write_bbp(dev, 0x1c, 0x00);
 933 
 934                         adm8211_write_bbp(dev, 0x1d, priv->eeprom->cr29);
 935                 }
 936         } else if (priv->bbp_type == ADM8211_TYPE_ADMTEK) {
 937                 /* reset baseband */
 938                 adm8211_write_bbp(dev, 0x00, 0xFF);
 939                 /* antenna selection: diversity */
 940                 adm8211_write_bbp(dev, 0x07, 0x0A);
 941 
 942                 /* TODO: find documentation for this */
 943                 switch (priv->transceiver_type) {
 944                 case ADM8211_RFMD2958:
 945                 case ADM8211_RFMD2958_RF3000_CONTROL_POWER:
 946                         adm8211_write_bbp(dev, 0x00, 0x00);
 947                         adm8211_write_bbp(dev, 0x01, 0x00);
 948                         adm8211_write_bbp(dev, 0x02, 0x00);
 949                         adm8211_write_bbp(dev, 0x03, 0x00);
 950                         adm8211_write_bbp(dev, 0x06, 0x0f);
 951                         adm8211_write_bbp(dev, 0x09, 0x00);
 952                         adm8211_write_bbp(dev, 0x0a, 0x00);
 953                         adm8211_write_bbp(dev, 0x0b, 0x00);
 954                         adm8211_write_bbp(dev, 0x0c, 0x00);
 955                         adm8211_write_bbp(dev, 0x0f, 0xAA);
 956                         adm8211_write_bbp(dev, 0x10, 0x8c);
 957                         adm8211_write_bbp(dev, 0x11, 0x43);
 958                         adm8211_write_bbp(dev, 0x18, 0x40);
 959                         adm8211_write_bbp(dev, 0x20, 0x23);
 960                         adm8211_write_bbp(dev, 0x21, 0x02);
 961                         adm8211_write_bbp(dev, 0x22, 0x28);
 962                         adm8211_write_bbp(dev, 0x23, 0x30);
 963                         adm8211_write_bbp(dev, 0x24, 0x2d);
 964                         adm8211_write_bbp(dev, 0x28, 0x35);
 965                         adm8211_write_bbp(dev, 0x2a, 0x8c);
 966                         adm8211_write_bbp(dev, 0x2b, 0x81);
 967                         adm8211_write_bbp(dev, 0x2c, 0x44);
 968                         adm8211_write_bbp(dev, 0x2d, 0x0A);
 969                         adm8211_write_bbp(dev, 0x29, 0x40);
 970                         adm8211_write_bbp(dev, 0x60, 0x08);
 971                         adm8211_write_bbp(dev, 0x64, 0x01);
 972                         break;
 973 
 974                 case ADM8211_MAX2820:
 975                         adm8211_write_bbp(dev, 0x00, 0x00);
 976                         adm8211_write_bbp(dev, 0x01, 0x00);
 977                         adm8211_write_bbp(dev, 0x02, 0x00);
 978                         adm8211_write_bbp(dev, 0x03, 0x00);
 979                         adm8211_write_bbp(dev, 0x06, 0x0f);
 980                         adm8211_write_bbp(dev, 0x09, 0x05);
 981                         adm8211_write_bbp(dev, 0x0a, 0x02);
 982                         adm8211_write_bbp(dev, 0x0b, 0x00);
 983                         adm8211_write_bbp(dev, 0x0c, 0x0f);
 984                         adm8211_write_bbp(dev, 0x0f, 0x55);
 985                         adm8211_write_bbp(dev, 0x10, 0x8d);
 986                         adm8211_write_bbp(dev, 0x11, 0x43);
 987                         adm8211_write_bbp(dev, 0x18, 0x4a);
 988                         adm8211_write_bbp(dev, 0x20, 0x20);
 989                         adm8211_write_bbp(dev, 0x21, 0x02);
 990                         adm8211_write_bbp(dev, 0x22, 0x23);
 991                         adm8211_write_bbp(dev, 0x23, 0x30);
 992                         adm8211_write_bbp(dev, 0x24, 0x2d);
 993                         adm8211_write_bbp(dev, 0x2a, 0x8c);
 994                         adm8211_write_bbp(dev, 0x2b, 0x81);
 995                         adm8211_write_bbp(dev, 0x2c, 0x44);
 996                         adm8211_write_bbp(dev, 0x29, 0x4a);
 997                         adm8211_write_bbp(dev, 0x60, 0x2b);
 998                         adm8211_write_bbp(dev, 0x64, 0x01);
 999                         break;
1000 
1001                 case ADM8211_AL2210L:
1002                         adm8211_write_bbp(dev, 0x00, 0x00);
1003                         adm8211_write_bbp(dev, 0x01, 0x00);
1004                         adm8211_write_bbp(dev, 0x02, 0x00);
1005                         adm8211_write_bbp(dev, 0x03, 0x00);
1006                         adm8211_write_bbp(dev, 0x06, 0x0f);
1007                         adm8211_write_bbp(dev, 0x07, 0x05);
1008                         adm8211_write_bbp(dev, 0x08, 0x03);
1009                         adm8211_write_bbp(dev, 0x09, 0x00);
1010                         adm8211_write_bbp(dev, 0x0a, 0x00);
1011                         adm8211_write_bbp(dev, 0x0b, 0x00);
1012                         adm8211_write_bbp(dev, 0x0c, 0x10);
1013                         adm8211_write_bbp(dev, 0x0f, 0x55);
1014                         adm8211_write_bbp(dev, 0x10, 0x8d);
1015                         adm8211_write_bbp(dev, 0x11, 0x43);
1016                         adm8211_write_bbp(dev, 0x18, 0x4a);
1017                         adm8211_write_bbp(dev, 0x20, 0x20);
1018                         adm8211_write_bbp(dev, 0x21, 0x02);
1019                         adm8211_write_bbp(dev, 0x22, 0x23);
1020                         adm8211_write_bbp(dev, 0x23, 0x30);
1021                         adm8211_write_bbp(dev, 0x24, 0x2d);
1022                         adm8211_write_bbp(dev, 0x2a, 0xaa);
1023                         adm8211_write_bbp(dev, 0x2b, 0x81);
1024                         adm8211_write_bbp(dev, 0x2c, 0x44);
1025                         adm8211_write_bbp(dev, 0x29, 0xfa);
1026                         adm8211_write_bbp(dev, 0x60, 0x2d);
1027                         adm8211_write_bbp(dev, 0x64, 0x01);
1028                         break;
1029 
1030                 case ADM8211_RFMD2948:
1031                         break;
1032 
1033                 default:
1034                         wiphy_debug(dev->wiphy, "unsupported transceiver %d\n",
1035                                     priv->transceiver_type);
1036                         break;
1037                 }
1038         } else
1039                 wiphy_debug(dev->wiphy, "unsupported BBP %d\n", priv->bbp_type);
1040 
1041         ADM8211_CSR_WRITE(SYNRF, 0);
1042 
1043         /* Set RF CAL control source to MAC control */
1044         reg = ADM8211_CSR_READ(SYNCTL);
1045         reg |= ADM8211_SYNCTL_SELCAL;
1046         ADM8211_CSR_WRITE(SYNCTL, reg);
1047 
1048         return 0;
1049 }
1050 
1051 /* configures hw beacons/probe responses */
1052 static int adm8211_set_rate(struct ieee80211_hw *dev)
1053 {
1054         struct adm8211_priv *priv = dev->priv;
1055         u32 reg;
1056         int i = 0;
1057         u8 rate_buf[12] = {0};
1058 
1059         /* write supported rates */
1060         if (priv->pdev->revision != ADM8211_REV_BA) {
1061                 rate_buf[0] = ARRAY_SIZE(adm8211_rates);
1062                 for (i = 0; i < ARRAY_SIZE(adm8211_rates); i++)
1063                         rate_buf[i + 1] = (adm8211_rates[i].bitrate / 5) | 0x80;
1064         } else {
1065                 /* workaround for rev BA specific bug */
1066                 rate_buf[0] = 0x04;
1067                 rate_buf[1] = 0x82;
1068                 rate_buf[2] = 0x04;
1069                 rate_buf[3] = 0x0b;
1070                 rate_buf[4] = 0x16;
1071         }
1072 
1073         adm8211_write_sram_bytes(dev, ADM8211_SRAM_SUPP_RATE, rate_buf,
1074                                  ARRAY_SIZE(adm8211_rates) + 1);
1075 
1076         reg = ADM8211_CSR_READ(PLCPHD) & 0x00FFFFFF; /* keep bits 0-23 */
1077         reg |= 1 << 15; /* short preamble */
1078         reg |= 110 << 24;
1079         ADM8211_CSR_WRITE(PLCPHD, reg);
1080 
1081         /* MTMLT   = 512 TU (max TX MSDU lifetime)
1082          * BCNTSIG = plcp_signal (beacon, probe resp, and atim TX rate)
1083          * SRTYLIM = 224 (short retry limit, TX header value is default) */
1084         ADM8211_CSR_WRITE(TXLMT, (512 << 16) | (110 << 8) | (224 << 0));
1085 
1086         return 0;
1087 }
1088 
1089 static void adm8211_hw_init(struct ieee80211_hw *dev)
1090 {
1091         struct adm8211_priv *priv = dev->priv;
1092         u32 reg;
1093         u8 cline;
1094 
1095         reg = ADM8211_CSR_READ(PAR);
1096         reg |= ADM8211_PAR_MRLE | ADM8211_PAR_MRME;
1097         reg &= ~(ADM8211_PAR_BAR | ADM8211_PAR_CAL);
1098 
1099         if (!pci_set_mwi(priv->pdev)) {
1100                 reg |= 0x1 << 24;
1101                 pci_read_config_byte(priv->pdev, PCI_CACHE_LINE_SIZE, &cline);
1102 
1103                 switch (cline) {
1104                 case  0x8:
1105                         reg |= (0x1 << 14);
1106                         break;
1107                 case 0x10:
1108                         reg |= (0x2 << 14);
1109                         break;
1110                 case 0x20:
1111                         reg |= (0x3 << 14);
1112                         break;
1113                 default:
1114                         reg |= (0x0 << 14);
1115                         break;
1116                 }
1117         }
1118 
1119         ADM8211_CSR_WRITE(PAR, reg);
1120 
1121         reg = ADM8211_CSR_READ(CSR_TEST1);
1122         reg &= ~(0xF << 28);
1123         reg |= (1 << 28) | (1 << 31);
1124         ADM8211_CSR_WRITE(CSR_TEST1, reg);
1125 
1126         /* lose link after 4 lost beacons */
1127         reg = (0x04 << 21) | ADM8211_WCSR_TSFTWE | ADM8211_WCSR_LSOE;
1128         ADM8211_CSR_WRITE(WCSR, reg);
1129 
1130         /* Disable APM, enable receive FIFO threshold, and set drain receive
1131          * threshold to store-and-forward */
1132         reg = ADM8211_CSR_READ(CMDR);
1133         reg &= ~(ADM8211_CMDR_APM | ADM8211_CMDR_DRT);
1134         reg |= ADM8211_CMDR_RTE | ADM8211_CMDR_DRT_SF;
1135         ADM8211_CSR_WRITE(CMDR, reg);
1136 
1137         adm8211_set_rate(dev);
1138 
1139         /* 4-bit values:
1140          * PWR1UP   = 8 * 2 ms
1141          * PWR0PAPE = 8 us or 5 us
1142          * PWR1PAPE = 1 us or 3 us
1143          * PWR0TRSW = 5 us
1144          * PWR1TRSW = 12 us
1145          * PWR0PE2  = 13 us
1146          * PWR1PE2  = 1 us
1147          * PWR0TXPE = 8 or 6 */
1148         if (priv->pdev->revision < ADM8211_REV_CA)
1149                 ADM8211_CSR_WRITE(TOFS2, 0x8815cd18);
1150         else
1151                 ADM8211_CSR_WRITE(TOFS2, 0x8535cd16);
1152 
1153         /* Enable store and forward for transmit */
1154         priv->nar = ADM8211_NAR_SF | ADM8211_NAR_PB;
1155         ADM8211_CSR_WRITE(NAR, priv->nar);
1156 
1157         /* Reset RF */
1158         ADM8211_CSR_WRITE(SYNRF, ADM8211_SYNRF_RADIO);
1159         ADM8211_CSR_READ(SYNRF);
1160         msleep(10);
1161         ADM8211_CSR_WRITE(SYNRF, 0);
1162         ADM8211_CSR_READ(SYNRF);
1163         msleep(5);
1164 
1165         /* Set CFP Max Duration to 0x10 TU */
1166         reg = ADM8211_CSR_READ(CFPP);
1167         reg &= ~(0xffff << 8);
1168         reg |= 0x0010 << 8;
1169         ADM8211_CSR_WRITE(CFPP, reg);
1170 
1171         /* USCNT = 0x16 (number of system clocks, 22 MHz, in 1us
1172          * TUCNT = 0x3ff - Tu counter 1024 us  */
1173         ADM8211_CSR_WRITE(TOFS0, (0x16 << 24) | 0x3ff);
1174 
1175         /* SLOT=20 us, SIFS=110 cycles of 22 MHz (5 us),
1176          * DIFS=50 us, EIFS=100 us */
1177         if (priv->pdev->revision < ADM8211_REV_CA)
1178                 ADM8211_CSR_WRITE(IFST, (20 << 23) | (110 << 15) |
1179                                         (50 << 9)  | 100);
1180         else
1181                 ADM8211_CSR_WRITE(IFST, (20 << 23) | (24 << 15) |
1182                                         (50 << 9)  | 100);
1183 
1184         /* PCNT = 1 (MAC idle time awake/sleep, unit S)
1185          * RMRD = 2346 * 8 + 1 us (max RX duration)  */
1186         ADM8211_CSR_WRITE(RMD, (1 << 16) | 18769);
1187 
1188         /* MART=65535 us, MIRT=256 us, TSFTOFST=0 us */
1189         ADM8211_CSR_WRITE(RSPT, 0xffffff00);
1190 
1191         /* Initialize BBP (and SYN) */
1192         adm8211_hw_init_bbp(dev);
1193 
1194         /* make sure interrupts are off */
1195         ADM8211_CSR_WRITE(IER, 0);
1196 
1197         /* ACK interrupts */
1198         ADM8211_CSR_WRITE(STSR, ADM8211_CSR_READ(STSR));
1199 
1200         /* Setup WEP (turns it off for now) */
1201         reg = ADM8211_CSR_READ(MACTEST);
1202         reg &= ~(7 << 20);
1203         ADM8211_CSR_WRITE(MACTEST, reg);
1204 
1205         reg = ADM8211_CSR_READ(WEPCTL);
1206         reg &= ~ADM8211_WEPCTL_WEPENABLE;
1207         reg |= ADM8211_WEPCTL_WEPRXBYP;
1208         ADM8211_CSR_WRITE(WEPCTL, reg);
1209 
1210         /* Clear the missed-packet counter. */
1211         ADM8211_CSR_READ(LPC);
1212 }
1213 
1214 static int adm8211_hw_reset(struct ieee80211_hw *dev)
1215 {
1216         struct adm8211_priv *priv = dev->priv;
1217         u32 reg, tmp;
1218         int timeout = 100;
1219 
1220         /* Power-on issue */
1221         /* TODO: check if this is necessary */
1222         ADM8211_CSR_WRITE(FRCTL, 0);
1223 
1224         /* Reset the chip */
1225         tmp = ADM8211_CSR_READ(PAR);
1226         ADM8211_CSR_WRITE(PAR, ADM8211_PAR_SWR);
1227 
1228         while ((ADM8211_CSR_READ(PAR) & ADM8211_PAR_SWR) && timeout--)
1229                 msleep(50);
1230 
1231         if (timeout <= 0)
1232                 return -ETIMEDOUT;
1233 
1234         ADM8211_CSR_WRITE(PAR, tmp);
1235 
1236         if (priv->pdev->revision == ADM8211_REV_BA &&
1237             (priv->transceiver_type == ADM8211_RFMD2958_RF3000_CONTROL_POWER ||
1238              priv->transceiver_type == ADM8211_RFMD2958)) {
1239                 reg = ADM8211_CSR_READ(CSR_TEST1);
1240                 reg |= (1 << 4) | (1 << 5);
1241                 ADM8211_CSR_WRITE(CSR_TEST1, reg);
1242         } else if (priv->pdev->revision == ADM8211_REV_CA) {
1243                 reg = ADM8211_CSR_READ(CSR_TEST1);
1244                 reg &= ~((1 << 4) | (1 << 5));
1245                 ADM8211_CSR_WRITE(CSR_TEST1, reg);
1246         }
1247 
1248         ADM8211_CSR_WRITE(FRCTL, 0);
1249 
1250         reg = ADM8211_CSR_READ(CSR_TEST0);
1251         reg |= ADM8211_CSR_TEST0_EPRLD; /* EEPROM Recall */
1252         ADM8211_CSR_WRITE(CSR_TEST0, reg);
1253 
1254         adm8211_clear_sram(dev);
1255 
1256         return 0;
1257 }
1258 
1259 static u64 adm8211_get_tsft(struct ieee80211_hw *dev,
1260                             struct ieee80211_vif *vif)
1261 {
1262         struct adm8211_priv *priv = dev->priv;
1263         u32 tsftl;
1264         u64 tsft;
1265 
1266         tsftl = ADM8211_CSR_READ(TSFTL);
1267         tsft = ADM8211_CSR_READ(TSFTH);
1268         tsft <<= 32;
1269         tsft |= tsftl;
1270 
1271         return tsft;
1272 }
1273 
1274 static void adm8211_set_interval(struct ieee80211_hw *dev,
1275                                  unsigned short bi, unsigned short li)
1276 {
1277         struct adm8211_priv *priv = dev->priv;
1278         u32 reg;
1279 
1280         /* BP (beacon interval) = data->beacon_interval
1281          * LI (listen interval) = data->listen_interval (in beacon intervals) */
1282         reg = (bi << 16) | li;
1283         ADM8211_CSR_WRITE(BPLI, reg);
1284 }
1285 
1286 static void adm8211_set_bssid(struct ieee80211_hw *dev, const u8 *bssid)
1287 {
1288         struct adm8211_priv *priv = dev->priv;
1289         u32 reg;
1290 
1291         ADM8211_CSR_WRITE(BSSID0, le32_to_cpu(*(__le32 *)bssid));
1292         reg = ADM8211_CSR_READ(ABDA1);
1293         reg &= 0x0000ffff;
1294         reg |= (bssid[4] << 16) | (bssid[5] << 24);
1295         ADM8211_CSR_WRITE(ABDA1, reg);
1296 }
1297 
1298 static int adm8211_config(struct ieee80211_hw *dev, u32 changed)
1299 {
1300         struct adm8211_priv *priv = dev->priv;
1301         struct ieee80211_conf *conf = &dev->conf;
1302         int channel =
1303                 ieee80211_frequency_to_channel(conf->chandef.chan->center_freq);
1304 
1305         if (channel != priv->channel) {
1306                 priv->channel = channel;
1307                 adm8211_rf_set_channel(dev, priv->channel);
1308         }
1309 
1310         return 0;
1311 }
1312 
1313 static void adm8211_bss_info_changed(struct ieee80211_hw *dev,
1314                                      struct ieee80211_vif *vif,
1315                                      struct ieee80211_bss_conf *conf,
1316                                      u32 changes)
1317 {
1318         struct adm8211_priv *priv = dev->priv;
1319 
1320         if (!(changes & BSS_CHANGED_BSSID))
1321                 return;
1322 
1323         if (!ether_addr_equal(conf->bssid, priv->bssid)) {
1324                 adm8211_set_bssid(dev, conf->bssid);
1325                 memcpy(priv->bssid, conf->bssid, ETH_ALEN);
1326         }
1327 }
1328 
1329 static u64 adm8211_prepare_multicast(struct ieee80211_hw *hw,
1330                                      struct netdev_hw_addr_list *mc_list)
1331 {
1332         unsigned int bit_nr;
1333         u32 mc_filter[2];
1334         struct netdev_hw_addr *ha;
1335 
1336         mc_filter[1] = mc_filter[0] = 0;
1337 
1338         netdev_hw_addr_list_for_each(ha, mc_list) {
1339                 bit_nr = ether_crc(ETH_ALEN, ha->addr) >> 26;
1340 
1341                 bit_nr &= 0x3F;
1342                 mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
1343         }
1344 
1345         return mc_filter[0] | ((u64)(mc_filter[1]) << 32);
1346 }
1347 
1348 static void adm8211_configure_filter(struct ieee80211_hw *dev,
1349                                      unsigned int changed_flags,
1350                                      unsigned int *total_flags,
1351                                      u64 multicast)
1352 {
1353         static const u8 bcast[ETH_ALEN] = { 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF };
1354         struct adm8211_priv *priv = dev->priv;
1355         unsigned int new_flags;
1356         u32 mc_filter[2];
1357 
1358         mc_filter[0] = multicast;
1359         mc_filter[1] = multicast >> 32;
1360 
1361         new_flags = 0;
1362 
1363         if (*total_flags & FIF_ALLMULTI || multicast == ~(0ULL)) {
1364                 new_flags |= FIF_ALLMULTI;
1365                 priv->nar &= ~ADM8211_NAR_PR;
1366                 priv->nar |= ADM8211_NAR_MM;
1367                 mc_filter[1] = mc_filter[0] = ~0;
1368         } else {
1369                 priv->nar &= ~(ADM8211_NAR_MM | ADM8211_NAR_PR);
1370         }
1371 
1372         ADM8211_IDLE_RX();
1373 
1374         ADM8211_CSR_WRITE(MAR0, mc_filter[0]);
1375         ADM8211_CSR_WRITE(MAR1, mc_filter[1]);
1376         ADM8211_CSR_READ(NAR);
1377 
1378         if (priv->nar & ADM8211_NAR_PR)
1379                 ieee80211_hw_set(dev, RX_INCLUDES_FCS);
1380         else
1381                 __clear_bit(IEEE80211_HW_RX_INCLUDES_FCS, dev->flags);
1382 
1383         if (*total_flags & FIF_BCN_PRBRESP_PROMISC)
1384                 adm8211_set_bssid(dev, bcast);
1385         else
1386                 adm8211_set_bssid(dev, priv->bssid);
1387 
1388         ADM8211_RESTORE();
1389 
1390         *total_flags = new_flags;
1391 }
1392 
1393 static int adm8211_add_interface(struct ieee80211_hw *dev,
1394                                  struct ieee80211_vif *vif)
1395 {
1396         struct adm8211_priv *priv = dev->priv;
1397         if (priv->mode != NL80211_IFTYPE_MONITOR)
1398                 return -EOPNOTSUPP;
1399 
1400         switch (vif->type) {
1401         case NL80211_IFTYPE_STATION:
1402                 priv->mode = vif->type;
1403                 break;
1404         default:
1405                 return -EOPNOTSUPP;
1406         }
1407 
1408         ADM8211_IDLE();
1409 
1410         ADM8211_CSR_WRITE(PAR0, le32_to_cpu(*(__le32 *)vif->addr));
1411         ADM8211_CSR_WRITE(PAR1, le16_to_cpu(*(__le16 *)(vif->addr + 4)));
1412 
1413         adm8211_update_mode(dev);
1414 
1415         ADM8211_RESTORE();
1416 
1417         return 0;
1418 }
1419 
1420 static void adm8211_remove_interface(struct ieee80211_hw *dev,
1421                                      struct ieee80211_vif *vif)
1422 {
1423         struct adm8211_priv *priv = dev->priv;
1424         priv->mode = NL80211_IFTYPE_MONITOR;
1425 }
1426 
1427 static int adm8211_init_rings(struct ieee80211_hw *dev)
1428 {
1429         struct adm8211_priv *priv = dev->priv;
1430         struct adm8211_desc *desc = NULL;
1431         struct adm8211_rx_ring_info *rx_info;
1432         struct adm8211_tx_ring_info *tx_info;
1433         unsigned int i;
1434 
1435         for (i = 0; i < priv->rx_ring_size; i++) {
1436                 desc = &priv->rx_ring[i];
1437                 desc->status = 0;
1438                 desc->length = cpu_to_le32(RX_PKT_SIZE);
1439                 priv->rx_buffers[i].skb = NULL;
1440         }
1441         /* Mark the end of RX ring; hw returns to base address after this
1442          * descriptor */
1443         desc->length |= cpu_to_le32(RDES1_CONTROL_RER);
1444 
1445         for (i = 0; i < priv->rx_ring_size; i++) {
1446                 desc = &priv->rx_ring[i];
1447                 rx_info = &priv->rx_buffers[i];
1448 
1449                 rx_info->skb = dev_alloc_skb(RX_PKT_SIZE);
1450                 if (rx_info->skb == NULL)
1451                         break;
1452                 rx_info->mapping = pci_map_single(priv->pdev,
1453                                                   skb_tail_pointer(rx_info->skb),
1454                                                   RX_PKT_SIZE,
1455                                                   PCI_DMA_FROMDEVICE);
1456                 if (pci_dma_mapping_error(priv->pdev, rx_info->mapping)) {
1457                         dev_kfree_skb(rx_info->skb);
1458                         rx_info->skb = NULL;
1459                         break;
1460                 }
1461 
1462                 desc->buffer1 = cpu_to_le32(rx_info->mapping);
1463                 desc->status = cpu_to_le32(RDES0_STATUS_OWN | RDES0_STATUS_SQL);
1464         }
1465 
1466         /* Setup TX ring. TX buffers descriptors will be filled in as needed */
1467         for (i = 0; i < priv->tx_ring_size; i++) {
1468                 desc = &priv->tx_ring[i];
1469                 tx_info = &priv->tx_buffers[i];
1470 
1471                 tx_info->skb = NULL;
1472                 tx_info->mapping = 0;
1473                 desc->status = 0;
1474         }
1475         desc->length = cpu_to_le32(TDES1_CONTROL_TER);
1476 
1477         priv->cur_rx = priv->cur_tx = priv->dirty_tx = 0;
1478         ADM8211_CSR_WRITE(RDB, priv->rx_ring_dma);
1479         ADM8211_CSR_WRITE(TDBD, priv->tx_ring_dma);
1480 
1481         return 0;
1482 }
1483 
1484 static void adm8211_free_rings(struct ieee80211_hw *dev)
1485 {
1486         struct adm8211_priv *priv = dev->priv;
1487         unsigned int i;
1488 
1489         for (i = 0; i < priv->rx_ring_size; i++) {
1490                 if (!priv->rx_buffers[i].skb)
1491                         continue;
1492 
1493                 pci_unmap_single(
1494                         priv->pdev,
1495                         priv->rx_buffers[i].mapping,
1496                         RX_PKT_SIZE, PCI_DMA_FROMDEVICE);
1497 
1498                 dev_kfree_skb(priv->rx_buffers[i].skb);
1499         }
1500 
1501         for (i = 0; i < priv->tx_ring_size; i++) {
1502                 if (!priv->tx_buffers[i].skb)
1503                         continue;
1504 
1505                 pci_unmap_single(priv->pdev,
1506                                  priv->tx_buffers[i].mapping,
1507                                  priv->tx_buffers[i].skb->len,
1508                                  PCI_DMA_TODEVICE);
1509 
1510                 dev_kfree_skb(priv->tx_buffers[i].skb);
1511         }
1512 }
1513 
1514 static int adm8211_start(struct ieee80211_hw *dev)
1515 {
1516         struct adm8211_priv *priv = dev->priv;
1517         int retval;
1518 
1519         /* Power up MAC and RF chips */
1520         retval = adm8211_hw_reset(dev);
1521         if (retval) {
1522                 wiphy_err(dev->wiphy, "hardware reset failed\n");
1523                 goto fail;
1524         }
1525 
1526         retval = adm8211_init_rings(dev);
1527         if (retval) {
1528                 wiphy_err(dev->wiphy, "failed to initialize rings\n");
1529                 goto fail;
1530         }
1531 
1532         /* Init hardware */
1533         adm8211_hw_init(dev);
1534         adm8211_rf_set_channel(dev, priv->channel);
1535 
1536         retval = request_irq(priv->pdev->irq, adm8211_interrupt,
1537                              IRQF_SHARED, "adm8211", dev);
1538         if (retval) {
1539                 wiphy_err(dev->wiphy, "failed to register IRQ handler\n");
1540                 goto fail;
1541         }
1542 
1543         ADM8211_CSR_WRITE(IER, ADM8211_IER_NIE | ADM8211_IER_AIE |
1544                                ADM8211_IER_RCIE | ADM8211_IER_TCIE |
1545                                ADM8211_IER_TDUIE | ADM8211_IER_GPTIE);
1546         priv->mode = NL80211_IFTYPE_MONITOR;
1547         adm8211_update_mode(dev);
1548         ADM8211_CSR_WRITE(RDR, 0);
1549 
1550         adm8211_set_interval(dev, 100, 10);
1551         return 0;
1552 
1553 fail:
1554         return retval;
1555 }
1556 
1557 static void adm8211_stop(struct ieee80211_hw *dev)
1558 {
1559         struct adm8211_priv *priv = dev->priv;
1560 
1561         priv->mode = NL80211_IFTYPE_UNSPECIFIED;
1562         priv->nar = 0;
1563         ADM8211_CSR_WRITE(NAR, 0);
1564         ADM8211_CSR_WRITE(IER, 0);
1565         ADM8211_CSR_READ(NAR);
1566 
1567         free_irq(priv->pdev->irq, dev);
1568 
1569         adm8211_free_rings(dev);
1570 }
1571 
1572 static void adm8211_calc_durations(int *dur, int *plcp, size_t payload_len, int len,
1573                                    int plcp_signal, int short_preamble)
1574 {
1575         /* Alternative calculation from NetBSD: */
1576 
1577 /* IEEE 802.11b durations for DSSS PHY in microseconds */
1578 #define IEEE80211_DUR_DS_LONG_PREAMBLE  144
1579 #define IEEE80211_DUR_DS_SHORT_PREAMBLE 72
1580 #define IEEE80211_DUR_DS_FAST_PLCPHDR   24
1581 #define IEEE80211_DUR_DS_SLOW_PLCPHDR   48
1582 #define IEEE80211_DUR_DS_SLOW_ACK       112
1583 #define IEEE80211_DUR_DS_FAST_ACK       56
1584 #define IEEE80211_DUR_DS_SLOW_CTS       112
1585 #define IEEE80211_DUR_DS_FAST_CTS       56
1586 #define IEEE80211_DUR_DS_SLOT           20
1587 #define IEEE80211_DUR_DS_SIFS           10
1588 
1589         int remainder;
1590 
1591         *dur = (80 * (24 + payload_len) + plcp_signal - 1)
1592                 / plcp_signal;
1593 
1594         if (plcp_signal <= PLCP_SIGNAL_2M)
1595                 /* 1-2Mbps WLAN: send ACK/CTS at 1Mbps */
1596                 *dur += 3 * (IEEE80211_DUR_DS_SIFS +
1597                              IEEE80211_DUR_DS_SHORT_PREAMBLE +
1598                              IEEE80211_DUR_DS_FAST_PLCPHDR) +
1599                              IEEE80211_DUR_DS_SLOW_CTS + IEEE80211_DUR_DS_SLOW_ACK;
1600         else
1601                 /* 5-11Mbps WLAN: send ACK/CTS at 2Mbps */
1602                 *dur += 3 * (IEEE80211_DUR_DS_SIFS +
1603                              IEEE80211_DUR_DS_SHORT_PREAMBLE +
1604                              IEEE80211_DUR_DS_FAST_PLCPHDR) +
1605                              IEEE80211_DUR_DS_FAST_CTS + IEEE80211_DUR_DS_FAST_ACK;
1606 
1607         /* lengthen duration if long preamble */
1608         if (!short_preamble)
1609                 *dur += 3 * (IEEE80211_DUR_DS_LONG_PREAMBLE -
1610                              IEEE80211_DUR_DS_SHORT_PREAMBLE) +
1611                         3 * (IEEE80211_DUR_DS_SLOW_PLCPHDR -
1612                              IEEE80211_DUR_DS_FAST_PLCPHDR);
1613 
1614 
1615         *plcp = (80 * len) / plcp_signal;
1616         remainder = (80 * len) % plcp_signal;
1617         if (plcp_signal == PLCP_SIGNAL_11M &&
1618             remainder <= 30 && remainder > 0)
1619                 *plcp = (*plcp | 0x8000) + 1;
1620         else if (remainder)
1621                 (*plcp)++;
1622 }
1623 
1624 /* Transmit skb w/adm8211_tx_hdr (802.11 header created by hardware) */
1625 static int adm8211_tx_raw(struct ieee80211_hw *dev, struct sk_buff *skb,
1626                            u16 plcp_signal,
1627                            size_t hdrlen)
1628 {
1629         struct adm8211_priv *priv = dev->priv;
1630         unsigned long flags;
1631         dma_addr_t mapping;
1632         unsigned int entry;
1633         u32 flag;
1634 
1635         mapping = pci_map_single(priv->pdev, skb->data, skb->len,
1636                                  PCI_DMA_TODEVICE);
1637         if (pci_dma_mapping_error(priv->pdev, mapping))
1638                 return -ENOMEM;
1639 
1640         spin_lock_irqsave(&priv->lock, flags);
1641 
1642         if (priv->cur_tx - priv->dirty_tx == priv->tx_ring_size / 2)
1643                 flag = TDES1_CONTROL_IC | TDES1_CONTROL_LS | TDES1_CONTROL_FS;
1644         else
1645                 flag = TDES1_CONTROL_LS | TDES1_CONTROL_FS;
1646 
1647         if (priv->cur_tx - priv->dirty_tx == priv->tx_ring_size - 2)
1648                 ieee80211_stop_queue(dev, 0);
1649 
1650         entry = priv->cur_tx % priv->tx_ring_size;
1651 
1652         priv->tx_buffers[entry].skb = skb;
1653         priv->tx_buffers[entry].mapping = mapping;
1654         priv->tx_buffers[entry].hdrlen = hdrlen;
1655         priv->tx_ring[entry].buffer1 = cpu_to_le32(mapping);
1656 
1657         if (entry == priv->tx_ring_size - 1)
1658                 flag |= TDES1_CONTROL_TER;
1659         priv->tx_ring[entry].length = cpu_to_le32(flag | skb->len);
1660 
1661         /* Set TX rate (SIGNAL field in PLCP PPDU format) */
1662         flag = TDES0_CONTROL_OWN | (plcp_signal << 20) | 8 /* ? */;
1663         priv->tx_ring[entry].status = cpu_to_le32(flag);
1664 
1665         priv->cur_tx++;
1666 
1667         spin_unlock_irqrestore(&priv->lock, flags);
1668 
1669         /* Trigger transmit poll */
1670         ADM8211_CSR_WRITE(TDR, 0);
1671 
1672         return 0;
1673 }
1674 
1675 /* Put adm8211_tx_hdr on skb and transmit */
1676 static void adm8211_tx(struct ieee80211_hw *dev,
1677                        struct ieee80211_tx_control *control,
1678                        struct sk_buff *skb)
1679 {
1680         struct adm8211_tx_hdr *txhdr;
1681         size_t payload_len, hdrlen;
1682         int plcp, dur, len, plcp_signal, short_preamble;
1683         struct ieee80211_hdr *hdr;
1684         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
1685         struct ieee80211_rate *txrate = ieee80211_get_tx_rate(dev, info);
1686         u8 rc_flags;
1687 
1688         rc_flags = info->control.rates[0].flags;
1689         short_preamble = !!(rc_flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE);
1690         plcp_signal = txrate->bitrate;
1691 
1692         hdr = (struct ieee80211_hdr *)skb->data;
1693         hdrlen = ieee80211_hdrlen(hdr->frame_control);
1694         memcpy(skb->cb, skb->data, hdrlen);
1695         hdr = (struct ieee80211_hdr *)skb->cb;
1696         skb_pull(skb, hdrlen);
1697         payload_len = skb->len;
1698 
1699         txhdr = skb_push(skb, sizeof(*txhdr));
1700         memset(txhdr, 0, sizeof(*txhdr));
1701         memcpy(txhdr->da, ieee80211_get_DA(hdr), ETH_ALEN);
1702         txhdr->signal = plcp_signal;
1703         txhdr->frame_body_size = cpu_to_le16(payload_len);
1704         txhdr->frame_control = hdr->frame_control;
1705 
1706         len = hdrlen + payload_len + FCS_LEN;
1707 
1708         txhdr->frag = cpu_to_le16(0x0FFF);
1709         adm8211_calc_durations(&dur, &plcp, payload_len,
1710                                len, plcp_signal, short_preamble);
1711         txhdr->plcp_frag_head_len = cpu_to_le16(plcp);
1712         txhdr->plcp_frag_tail_len = cpu_to_le16(plcp);
1713         txhdr->dur_frag_head = cpu_to_le16(dur);
1714         txhdr->dur_frag_tail = cpu_to_le16(dur);
1715 
1716         txhdr->header_control = cpu_to_le16(ADM8211_TXHDRCTL_ENABLE_EXTEND_HEADER);
1717 
1718         if (short_preamble)
1719                 txhdr->header_control |= cpu_to_le16(ADM8211_TXHDRCTL_SHORT_PREAMBLE);
1720 
1721         if (rc_flags & IEEE80211_TX_RC_USE_RTS_CTS)
1722                 txhdr->header_control |= cpu_to_le16(ADM8211_TXHDRCTL_ENABLE_RTS);
1723 
1724         txhdr->retry_limit = info->control.rates[0].count;
1725 
1726         if (adm8211_tx_raw(dev, skb, plcp_signal, hdrlen)) {
1727                 /* Drop packet */
1728                 ieee80211_free_txskb(dev, skb);
1729         }
1730 }
1731 
1732 static int adm8211_alloc_rings(struct ieee80211_hw *dev)
1733 {
1734         struct adm8211_priv *priv = dev->priv;
1735         unsigned int ring_size;
1736 
1737         priv->rx_buffers = kmalloc(sizeof(*priv->rx_buffers) * priv->rx_ring_size +
1738                                    sizeof(*priv->tx_buffers) * priv->tx_ring_size, GFP_KERNEL);
1739         if (!priv->rx_buffers)
1740                 return -ENOMEM;
1741 
1742         priv->tx_buffers = (void *)priv->rx_buffers +
1743                            sizeof(*priv->rx_buffers) * priv->rx_ring_size;
1744 
1745         /* Allocate TX/RX descriptors */
1746         ring_size = sizeof(struct adm8211_desc) * priv->rx_ring_size +
1747                     sizeof(struct adm8211_desc) * priv->tx_ring_size;
1748         priv->rx_ring = pci_alloc_consistent(priv->pdev, ring_size,
1749                                              &priv->rx_ring_dma);
1750 
1751         if (!priv->rx_ring) {
1752                 kfree(priv->rx_buffers);
1753                 priv->rx_buffers = NULL;
1754                 priv->tx_buffers = NULL;
1755                 return -ENOMEM;
1756         }
1757 
1758         priv->tx_ring = priv->rx_ring + priv->rx_ring_size;
1759         priv->tx_ring_dma = priv->rx_ring_dma +
1760                             sizeof(struct adm8211_desc) * priv->rx_ring_size;
1761 
1762         return 0;
1763 }
1764 
1765 static const struct ieee80211_ops adm8211_ops = {
1766         .tx                     = adm8211_tx,
1767         .start                  = adm8211_start,
1768         .stop                   = adm8211_stop,
1769         .add_interface          = adm8211_add_interface,
1770         .remove_interface       = adm8211_remove_interface,
1771         .config                 = adm8211_config,
1772         .bss_info_changed       = adm8211_bss_info_changed,
1773         .prepare_multicast      = adm8211_prepare_multicast,
1774         .configure_filter       = adm8211_configure_filter,
1775         .get_stats              = adm8211_get_stats,
1776         .get_tsf                = adm8211_get_tsft
1777 };
1778 
1779 static int adm8211_probe(struct pci_dev *pdev,
1780                                    const struct pci_device_id *id)
1781 {
1782         struct ieee80211_hw *dev;
1783         struct adm8211_priv *priv;
1784         unsigned long mem_addr, mem_len;
1785         unsigned int io_addr, io_len;
1786         int err;
1787         u32 reg;
1788         u8 perm_addr[ETH_ALEN];
1789 
1790         err = pci_enable_device(pdev);
1791         if (err) {
1792                 printk(KERN_ERR "%s (adm8211): Cannot enable new PCI device\n",
1793                        pci_name(pdev));
1794                 return err;
1795         }
1796 
1797         io_addr = pci_resource_start(pdev, 0);
1798         io_len = pci_resource_len(pdev, 0);
1799         mem_addr = pci_resource_start(pdev, 1);
1800         mem_len = pci_resource_len(pdev, 1);
1801         if (io_len < 256 || mem_len < 1024) {
1802                 printk(KERN_ERR "%s (adm8211): Too short PCI resources\n",
1803                        pci_name(pdev));
1804                 goto err_disable_pdev;
1805         }
1806 
1807 
1808         /* check signature */
1809         pci_read_config_dword(pdev, 0x80 /* CR32 */, &reg);
1810         if (reg != ADM8211_SIG1 && reg != ADM8211_SIG2) {
1811                 printk(KERN_ERR "%s (adm8211): Invalid signature (0x%x)\n",
1812                        pci_name(pdev), reg);
1813                 goto err_disable_pdev;
1814         }
1815 
1816         err = pci_request_regions(pdev, "adm8211");
1817         if (err) {
1818                 printk(KERN_ERR "%s (adm8211): Cannot obtain PCI resources\n",
1819                        pci_name(pdev));
1820                 return err; /* someone else grabbed it? don't disable it */
1821         }
1822 
1823         if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32)) ||
1824             pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
1825                 printk(KERN_ERR "%s (adm8211): No suitable DMA available\n",
1826                        pci_name(pdev));
1827                 goto err_free_reg;
1828         }
1829 
1830         pci_set_master(pdev);
1831 
1832         dev = ieee80211_alloc_hw(sizeof(*priv), &adm8211_ops);
1833         if (!dev) {
1834                 printk(KERN_ERR "%s (adm8211): ieee80211 alloc failed\n",
1835                        pci_name(pdev));
1836                 err = -ENOMEM;
1837                 goto err_free_reg;
1838         }
1839         priv = dev->priv;
1840         priv->pdev = pdev;
1841 
1842         spin_lock_init(&priv->lock);
1843 
1844         SET_IEEE80211_DEV(dev, &pdev->dev);
1845 
1846         pci_set_drvdata(pdev, dev);
1847 
1848         priv->map = pci_iomap(pdev, 1, mem_len);
1849         if (!priv->map)
1850                 priv->map = pci_iomap(pdev, 0, io_len);
1851 
1852         if (!priv->map) {
1853                 printk(KERN_ERR "%s (adm8211): Cannot map device memory\n",
1854                        pci_name(pdev));
1855                 err = -ENOMEM;
1856                 goto err_free_dev;
1857         }
1858 
1859         priv->rx_ring_size = rx_ring_size;
1860         priv->tx_ring_size = tx_ring_size;
1861 
1862         err = adm8211_alloc_rings(dev);
1863         if (err) {
1864                 printk(KERN_ERR "%s (adm8211): Cannot allocate TX/RX ring\n",
1865                        pci_name(pdev));
1866                 goto err_iounmap;
1867         }
1868 
1869         *(__le32 *)perm_addr = cpu_to_le32(ADM8211_CSR_READ(PAR0));
1870         *(__le16 *)&perm_addr[4] =
1871                 cpu_to_le16(ADM8211_CSR_READ(PAR1) & 0xFFFF);
1872 
1873         if (!is_valid_ether_addr(perm_addr)) {
1874                 printk(KERN_WARNING "%s (adm8211): Invalid hwaddr in EEPROM!\n",
1875                        pci_name(pdev));
1876                 eth_random_addr(perm_addr);
1877         }
1878         SET_IEEE80211_PERM_ADDR(dev, perm_addr);
1879 
1880         dev->extra_tx_headroom = sizeof(struct adm8211_tx_hdr);
1881         /* dev->flags = RX_INCLUDES_FCS in promisc mode */
1882         ieee80211_hw_set(dev, SIGNAL_UNSPEC);
1883         dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
1884 
1885         dev->max_signal = 100;    /* FIXME: find better value */
1886 
1887         dev->queues = 1; /* ADM8211C supports more, maybe ADM8211B too */
1888 
1889         priv->retry_limit = 3;
1890         priv->ant_power = 0x40;
1891         priv->tx_power = 0x40;
1892         priv->lpf_cutoff = 0xFF;
1893         priv->lnags_threshold = 0xFF;
1894         priv->mode = NL80211_IFTYPE_UNSPECIFIED;
1895 
1896         /* Power-on issue. EEPROM won't read correctly without */
1897         if (pdev->revision >= ADM8211_REV_BA) {
1898                 ADM8211_CSR_WRITE(FRCTL, 0);
1899                 ADM8211_CSR_READ(FRCTL);
1900                 ADM8211_CSR_WRITE(FRCTL, 1);
1901                 ADM8211_CSR_READ(FRCTL);
1902                 msleep(100);
1903         }
1904 
1905         err = adm8211_read_eeprom(dev);
1906         if (err) {
1907                 printk(KERN_ERR "%s (adm8211): Can't alloc eeprom buffer\n",
1908                        pci_name(pdev));
1909                 goto err_free_desc;
1910         }
1911 
1912         priv->channel = 1;
1913 
1914         dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band;
1915 
1916         wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST);
1917 
1918         err = ieee80211_register_hw(dev);
1919         if (err) {
1920                 printk(KERN_ERR "%s (adm8211): Cannot register device\n",
1921                        pci_name(pdev));
1922                 goto err_free_eeprom;
1923         }
1924 
1925         wiphy_info(dev->wiphy, "hwaddr %pM, Rev 0x%02x\n",
1926                    dev->wiphy->perm_addr, pdev->revision);
1927 
1928         return 0;
1929 
1930  err_free_eeprom:
1931         kfree(priv->eeprom);
1932 
1933  err_free_desc:
1934         pci_free_consistent(pdev,
1935                             sizeof(struct adm8211_desc) * priv->rx_ring_size +
1936                             sizeof(struct adm8211_desc) * priv->tx_ring_size,
1937                             priv->rx_ring, priv->rx_ring_dma);
1938         kfree(priv->rx_buffers);
1939 
1940  err_iounmap:
1941         pci_iounmap(pdev, priv->map);
1942 
1943  err_free_dev:
1944         ieee80211_free_hw(dev);
1945 
1946  err_free_reg:
1947         pci_release_regions(pdev);
1948 
1949  err_disable_pdev:
1950         pci_disable_device(pdev);
1951         return err;
1952 }
1953 
1954 
1955 static void adm8211_remove(struct pci_dev *pdev)
1956 {
1957         struct ieee80211_hw *dev = pci_get_drvdata(pdev);
1958         struct adm8211_priv *priv;
1959 
1960         if (!dev)
1961                 return;
1962 
1963         ieee80211_unregister_hw(dev);
1964 
1965         priv = dev->priv;
1966 
1967         pci_free_consistent(pdev,
1968                             sizeof(struct adm8211_desc) * priv->rx_ring_size +
1969                             sizeof(struct adm8211_desc) * priv->tx_ring_size,
1970                             priv->rx_ring, priv->rx_ring_dma);
1971 
1972         kfree(priv->rx_buffers);
1973         kfree(priv->eeprom);
1974         pci_iounmap(pdev, priv->map);
1975         pci_release_regions(pdev);
1976         pci_disable_device(pdev);
1977         ieee80211_free_hw(dev);
1978 }
1979 
1980 
1981 #ifdef CONFIG_PM
1982 static int adm8211_suspend(struct pci_dev *pdev, pm_message_t state)
1983 {
1984         pci_save_state(pdev);
1985         pci_set_power_state(pdev, pci_choose_state(pdev, state));
1986         return 0;
1987 }
1988 
1989 static int adm8211_resume(struct pci_dev *pdev)
1990 {
1991         pci_set_power_state(pdev, PCI_D0);
1992         pci_restore_state(pdev);
1993         return 0;
1994 }
1995 #endif /* CONFIG_PM */
1996 
1997 
1998 MODULE_DEVICE_TABLE(pci, adm8211_pci_id_table);
1999 
2000 /* TODO: implement enable_wake */
2001 static struct pci_driver adm8211_driver = {
2002         .name           = "adm8211",
2003         .id_table       = adm8211_pci_id_table,
2004         .probe          = adm8211_probe,
2005         .remove         = adm8211_remove,
2006 #ifdef CONFIG_PM
2007         .suspend        = adm8211_suspend,
2008         .resume         = adm8211_resume,
2009 #endif /* CONFIG_PM */
2010 };
2011 
2012 module_pci_driver(adm8211_driver);

/* [<][>][^][v][top][bottom][index][help] */