drivers/net/wireless/ralink/rt2x00/rt2400pci.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
rt2400pci_bbp_write
rt2400pci_bbp_read
rt2400pci_rf_write
rt2400pci_eepromregister_read
rt2400pci_eepromregister_write
rt2400pci_rfkill_poll
rt2400pci_brightness_set
rt2400pci_blink_set
rt2400pci_init_led
rt2400pci_config_filter
rt2400pci_config_intf
rt2400pci_config_erp
rt2400pci_config_ant
rt2400pci_config_channel
rt2400pci_config_txpower
rt2400pci_config_retry_limit
rt2400pci_config_ps
rt2400pci_config
rt2400pci_config_cw
rt2400pci_link_stats
rt2400pci_set_vgc
rt2400pci_reset_tuner
rt2400pci_link_tuner
rt2400pci_start_queue
rt2400pci_kick_queue
rt2400pci_stop_queue
rt2400pci_get_entry_state
rt2400pci_clear_entry
rt2400pci_init_queues
rt2400pci_init_registers
rt2400pci_wait_bbp_ready
rt2400pci_init_bbp
rt2400pci_toggle_irq
rt2400pci_enable_radio
rt2400pci_disable_radio
rt2400pci_set_state
rt2400pci_set_device_state
rt2400pci_write_tx_desc
rt2400pci_write_beacon
rt2400pci_fill_rxdone
rt2400pci_txdone
rt2400pci_enable_interrupt
rt2400pci_txstatus_tasklet
rt2400pci_tbtt_tasklet
rt2400pci_rxdone_tasklet
rt2400pci_interrupt
rt2400pci_validate_eeprom
rt2400pci_init_eeprom
rt2400pci_probe_hw_mode
rt2400pci_probe_hw
rt2400pci_conf_tx
rt2400pci_get_tsf
rt2400pci_tx_last_beacon
rt2400pci_queue_init
rt2400pci_probe
   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3         Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com>
   4         <http://rt2x00.serialmonkey.com>
   5 
   6  */
   7 
   8 /*
   9         Module: rt2400pci
  10         Abstract: rt2400pci device specific routines.
  11         Supported chipsets: RT2460.
  12  */
  13 
  14 #include <linux/delay.h>
  15 #include <linux/etherdevice.h>
  16 #include <linux/kernel.h>
  17 #include <linux/module.h>
  18 #include <linux/pci.h>
  19 #include <linux/eeprom_93cx6.h>
  20 #include <linux/slab.h>
  21 
  22 #include "rt2x00.h"
  23 #include "rt2x00mmio.h"
  24 #include "rt2x00pci.h"
  25 #include "rt2400pci.h"
  26 
  27 /*
  28  * Register access.
  29  * All access to the CSR registers will go through the methods
  30  * rt2x00mmio_register_read and rt2x00mmio_register_write.
  31  * BBP and RF register require indirect register access,
  32  * and use the CSR registers BBPCSR and RFCSR to achieve this.
  33  * These indirect registers work with busy bits,
  34  * and we will try maximal REGISTER_BUSY_COUNT times to access
  35  * the register while taking a REGISTER_BUSY_DELAY us delay
  36  * between each attempt. When the busy bit is still set at that time,
  37  * the access attempt is considered to have failed,
  38  * and we will print an error.
  39  */
  40 #define WAIT_FOR_BBP(__dev, __reg) \
  41         rt2x00mmio_regbusy_read((__dev), BBPCSR, BBPCSR_BUSY, (__reg))
  42 #define WAIT_FOR_RF(__dev, __reg) \
  43         rt2x00mmio_regbusy_read((__dev), RFCSR, RFCSR_BUSY, (__reg))
  44 
  45 static void rt2400pci_bbp_write(struct rt2x00_dev *rt2x00dev,
  46                                 const unsigned int word, const u8 value)
  47 {
  48         u32 reg;
  49 
  50         mutex_lock(&rt2x00dev->csr_mutex);
  51 
  52         /*
  53          * Wait until the BBP becomes available, afterwards we
  54          * can safely write the new data into the register.
  55          */
  56         if (WAIT_FOR_BBP(rt2x00dev, &reg)) {
  57                 reg = 0;
  58                 rt2x00_set_field32(&reg, BBPCSR_VALUE, value);
  59                 rt2x00_set_field32(&reg, BBPCSR_REGNUM, word);
  60                 rt2x00_set_field32(&reg, BBPCSR_BUSY, 1);
  61                 rt2x00_set_field32(&reg, BBPCSR_WRITE_CONTROL, 1);
  62 
  63                 rt2x00mmio_register_write(rt2x00dev, BBPCSR, reg);
  64         }
  65 
  66         mutex_unlock(&rt2x00dev->csr_mutex);
  67 }
  68 
  69 static u8 rt2400pci_bbp_read(struct rt2x00_dev *rt2x00dev,
  70                              const unsigned int word)
  71 {
  72         u32 reg;
  73         u8 value;
  74 
  75         mutex_lock(&rt2x00dev->csr_mutex);
  76 
  77         /*
  78          * Wait until the BBP becomes available, afterwards we
  79          * can safely write the read request into the register.
  80          * After the data has been written, we wait until hardware
  81          * returns the correct value, if at any time the register
  82          * doesn't become available in time, reg will be 0xffffffff
  83          * which means we return 0xff to the caller.
  84          */
  85         if (WAIT_FOR_BBP(rt2x00dev, &reg)) {
  86                 reg = 0;
  87                 rt2x00_set_field32(&reg, BBPCSR_REGNUM, word);
  88                 rt2x00_set_field32(&reg, BBPCSR_BUSY, 1);
  89                 rt2x00_set_field32(&reg, BBPCSR_WRITE_CONTROL, 0);
  90 
  91                 rt2x00mmio_register_write(rt2x00dev, BBPCSR, reg);
  92 
  93                 WAIT_FOR_BBP(rt2x00dev, &reg);
  94         }
  95 
  96         value = rt2x00_get_field32(reg, BBPCSR_VALUE);
  97 
  98         mutex_unlock(&rt2x00dev->csr_mutex);
  99 
 100         return value;
 101 }
 102 
 103 static void rt2400pci_rf_write(struct rt2x00_dev *rt2x00dev,
 104                                const unsigned int word, const u32 value)
 105 {
 106         u32 reg;
 107 
 108         mutex_lock(&rt2x00dev->csr_mutex);
 109 
 110         /*
 111          * Wait until the RF becomes available, afterwards we
 112          * can safely write the new data into the register.
 113          */
 114         if (WAIT_FOR_RF(rt2x00dev, &reg)) {
 115                 reg = 0;
 116                 rt2x00_set_field32(&reg, RFCSR_VALUE, value);
 117                 rt2x00_set_field32(&reg, RFCSR_NUMBER_OF_BITS, 20);
 118                 rt2x00_set_field32(&reg, RFCSR_IF_SELECT, 0);
 119                 rt2x00_set_field32(&reg, RFCSR_BUSY, 1);
 120 
 121                 rt2x00mmio_register_write(rt2x00dev, RFCSR, reg);
 122                 rt2x00_rf_write(rt2x00dev, word, value);
 123         }
 124 
 125         mutex_unlock(&rt2x00dev->csr_mutex);
 126 }
 127 
 128 static void rt2400pci_eepromregister_read(struct eeprom_93cx6 *eeprom)
 129 {
 130         struct rt2x00_dev *rt2x00dev = eeprom->data;
 131         u32 reg;
 132 
 133         reg = rt2x00mmio_register_read(rt2x00dev, CSR21);
 134 
 135         eeprom->reg_data_in = !!rt2x00_get_field32(reg, CSR21_EEPROM_DATA_IN);
 136         eeprom->reg_data_out = !!rt2x00_get_field32(reg, CSR21_EEPROM_DATA_OUT);
 137         eeprom->reg_data_clock =
 138             !!rt2x00_get_field32(reg, CSR21_EEPROM_DATA_CLOCK);
 139         eeprom->reg_chip_select =
 140             !!rt2x00_get_field32(reg, CSR21_EEPROM_CHIP_SELECT);
 141 }
 142 
 143 static void rt2400pci_eepromregister_write(struct eeprom_93cx6 *eeprom)
 144 {
 145         struct rt2x00_dev *rt2x00dev = eeprom->data;
 146         u32 reg = 0;
 147 
 148         rt2x00_set_field32(&reg, CSR21_EEPROM_DATA_IN, !!eeprom->reg_data_in);
 149         rt2x00_set_field32(&reg, CSR21_EEPROM_DATA_OUT, !!eeprom->reg_data_out);
 150         rt2x00_set_field32(&reg, CSR21_EEPROM_DATA_CLOCK,
 151                            !!eeprom->reg_data_clock);
 152         rt2x00_set_field32(&reg, CSR21_EEPROM_CHIP_SELECT,
 153                            !!eeprom->reg_chip_select);
 154 
 155         rt2x00mmio_register_write(rt2x00dev, CSR21, reg);
 156 }
 157 
 158 #ifdef CONFIG_RT2X00_LIB_DEBUGFS
 159 static const struct rt2x00debug rt2400pci_rt2x00debug = {
 160         .owner  = THIS_MODULE,
 161         .csr    = {
 162                 .read           = rt2x00mmio_register_read,
 163                 .write          = rt2x00mmio_register_write,
 164                 .flags          = RT2X00DEBUGFS_OFFSET,
 165                 .word_base      = CSR_REG_BASE,
 166                 .word_size      = sizeof(u32),
 167                 .word_count     = CSR_REG_SIZE / sizeof(u32),
 168         },
 169         .eeprom = {
 170                 .read           = rt2x00_eeprom_read,
 171                 .write          = rt2x00_eeprom_write,
 172                 .word_base      = EEPROM_BASE,
 173                 .word_size      = sizeof(u16),
 174                 .word_count     = EEPROM_SIZE / sizeof(u16),
 175         },
 176         .bbp    = {
 177                 .read           = rt2400pci_bbp_read,
 178                 .write          = rt2400pci_bbp_write,
 179                 .word_base      = BBP_BASE,
 180                 .word_size      = sizeof(u8),
 181                 .word_count     = BBP_SIZE / sizeof(u8),
 182         },
 183         .rf     = {
 184                 .read           = rt2x00_rf_read,
 185                 .write          = rt2400pci_rf_write,
 186                 .word_base      = RF_BASE,
 187                 .word_size      = sizeof(u32),
 188                 .word_count     = RF_SIZE / sizeof(u32),
 189         },
 190 };
 191 #endif /* CONFIG_RT2X00_LIB_DEBUGFS */
 192 
 193 static int rt2400pci_rfkill_poll(struct rt2x00_dev *rt2x00dev)
 194 {
 195         u32 reg;
 196 
 197         reg = rt2x00mmio_register_read(rt2x00dev, GPIOCSR);
 198         return rt2x00_get_field32(reg, GPIOCSR_VAL0);
 199 }
 200 
 201 #ifdef CONFIG_RT2X00_LIB_LEDS
 202 static void rt2400pci_brightness_set(struct led_classdev *led_cdev,
 203                                      enum led_brightness brightness)
 204 {
 205         struct rt2x00_led *led =
 206             container_of(led_cdev, struct rt2x00_led, led_dev);
 207         unsigned int enabled = brightness != LED_OFF;
 208         u32 reg;
 209 
 210         reg = rt2x00mmio_register_read(led->rt2x00dev, LEDCSR);
 211 
 212         if (led->type == LED_TYPE_RADIO || led->type == LED_TYPE_ASSOC)
 213                 rt2x00_set_field32(&reg, LEDCSR_LINK, enabled);
 214         else if (led->type == LED_TYPE_ACTIVITY)
 215                 rt2x00_set_field32(&reg, LEDCSR_ACTIVITY, enabled);
 216 
 217         rt2x00mmio_register_write(led->rt2x00dev, LEDCSR, reg);
 218 }
 219 
 220 static int rt2400pci_blink_set(struct led_classdev *led_cdev,
 221                                unsigned long *delay_on,
 222                                unsigned long *delay_off)
 223 {
 224         struct rt2x00_led *led =
 225             container_of(led_cdev, struct rt2x00_led, led_dev);
 226         u32 reg;
 227 
 228         reg = rt2x00mmio_register_read(led->rt2x00dev, LEDCSR);
 229         rt2x00_set_field32(&reg, LEDCSR_ON_PERIOD, *delay_on);
 230         rt2x00_set_field32(&reg, LEDCSR_OFF_PERIOD, *delay_off);
 231         rt2x00mmio_register_write(led->rt2x00dev, LEDCSR, reg);
 232 
 233         return 0;
 234 }
 235 
 236 static void rt2400pci_init_led(struct rt2x00_dev *rt2x00dev,
 237                                struct rt2x00_led *led,
 238                                enum led_type type)
 239 {
 240         led->rt2x00dev = rt2x00dev;
 241         led->type = type;
 242         led->led_dev.brightness_set = rt2400pci_brightness_set;
 243         led->led_dev.blink_set = rt2400pci_blink_set;
 244         led->flags = LED_INITIALIZED;
 245 }
 246 #endif /* CONFIG_RT2X00_LIB_LEDS */
 247 
 248 /*
 249  * Configuration handlers.
 250  */
 251 static void rt2400pci_config_filter(struct rt2x00_dev *rt2x00dev,
 252                                     const unsigned int filter_flags)
 253 {
 254         u32 reg;
 255 
 256         /*
 257          * Start configuration steps.
 258          * Note that the version error will always be dropped
 259          * since there is no filter for it at this time.
 260          */
 261         reg = rt2x00mmio_register_read(rt2x00dev, RXCSR0);
 262         rt2x00_set_field32(&reg, RXCSR0_DROP_CRC,
 263                            !(filter_flags & FIF_FCSFAIL));
 264         rt2x00_set_field32(&reg, RXCSR0_DROP_PHYSICAL,
 265                            !(filter_flags & FIF_PLCPFAIL));
 266         rt2x00_set_field32(&reg, RXCSR0_DROP_CONTROL,
 267                            !(filter_flags & FIF_CONTROL));
 268         rt2x00_set_field32(&reg, RXCSR0_DROP_NOT_TO_ME,
 269                            !test_bit(CONFIG_MONITORING, &rt2x00dev->flags));
 270         rt2x00_set_field32(&reg, RXCSR0_DROP_TODS,
 271                            !test_bit(CONFIG_MONITORING, &rt2x00dev->flags) &&
 272                            !rt2x00dev->intf_ap_count);
 273         rt2x00_set_field32(&reg, RXCSR0_DROP_VERSION_ERROR, 1);
 274         rt2x00mmio_register_write(rt2x00dev, RXCSR0, reg);
 275 }
 276 
 277 static void rt2400pci_config_intf(struct rt2x00_dev *rt2x00dev,
 278                                   struct rt2x00_intf *intf,
 279                                   struct rt2x00intf_conf *conf,
 280                                   const unsigned int flags)
 281 {
 282         unsigned int bcn_preload;
 283         u32 reg;
 284 
 285         if (flags & CONFIG_UPDATE_TYPE) {
 286                 /*
 287                  * Enable beacon config
 288                  */
 289                 bcn_preload = PREAMBLE + GET_DURATION(IEEE80211_HEADER, 20);
 290                 reg = rt2x00mmio_register_read(rt2x00dev, BCNCSR1);
 291                 rt2x00_set_field32(&reg, BCNCSR1_PRELOAD, bcn_preload);
 292                 rt2x00mmio_register_write(rt2x00dev, BCNCSR1, reg);
 293 
 294                 /*
 295                  * Enable synchronisation.
 296                  */
 297                 reg = rt2x00mmio_register_read(rt2x00dev, CSR14);
 298                 rt2x00_set_field32(&reg, CSR14_TSF_SYNC, conf->sync);
 299                 rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
 300         }
 301 
 302         if (flags & CONFIG_UPDATE_MAC)
 303                 rt2x00mmio_register_multiwrite(rt2x00dev, CSR3,
 304                                                conf->mac, sizeof(conf->mac));
 305 
 306         if (flags & CONFIG_UPDATE_BSSID)
 307                 rt2x00mmio_register_multiwrite(rt2x00dev, CSR5,
 308                                                conf->bssid,
 309                                                sizeof(conf->bssid));
 310 }
 311 
 312 static void rt2400pci_config_erp(struct rt2x00_dev *rt2x00dev,
 313                                  struct rt2x00lib_erp *erp,
 314                                  u32 changed)
 315 {
 316         int preamble_mask;
 317         u32 reg;
 318 
 319         /*
 320          * When short preamble is enabled, we should set bit 0x08
 321          */
 322         if (changed & BSS_CHANGED_ERP_PREAMBLE) {
 323                 preamble_mask = erp->short_preamble << 3;
 324 
 325                 reg = rt2x00mmio_register_read(rt2x00dev, TXCSR1);
 326                 rt2x00_set_field32(&reg, TXCSR1_ACK_TIMEOUT, 0x1ff);
 327                 rt2x00_set_field32(&reg, TXCSR1_ACK_CONSUME_TIME, 0x13a);
 328                 rt2x00_set_field32(&reg, TXCSR1_TSF_OFFSET, IEEE80211_HEADER);
 329                 rt2x00_set_field32(&reg, TXCSR1_AUTORESPONDER, 1);
 330                 rt2x00mmio_register_write(rt2x00dev, TXCSR1, reg);
 331 
 332                 reg = rt2x00mmio_register_read(rt2x00dev, ARCSR2);
 333                 rt2x00_set_field32(&reg, ARCSR2_SIGNAL, 0x00);
 334                 rt2x00_set_field32(&reg, ARCSR2_SERVICE, 0x04);
 335                 rt2x00_set_field32(&reg, ARCSR2_LENGTH,
 336                                    GET_DURATION(ACK_SIZE, 10));
 337                 rt2x00mmio_register_write(rt2x00dev, ARCSR2, reg);
 338 
 339                 reg = rt2x00mmio_register_read(rt2x00dev, ARCSR3);
 340                 rt2x00_set_field32(&reg, ARCSR3_SIGNAL, 0x01 | preamble_mask);
 341                 rt2x00_set_field32(&reg, ARCSR3_SERVICE, 0x04);
 342                 rt2x00_set_field32(&reg, ARCSR2_LENGTH,
 343                                    GET_DURATION(ACK_SIZE, 20));
 344                 rt2x00mmio_register_write(rt2x00dev, ARCSR3, reg);
 345 
 346                 reg = rt2x00mmio_register_read(rt2x00dev, ARCSR4);
 347                 rt2x00_set_field32(&reg, ARCSR4_SIGNAL, 0x02 | preamble_mask);
 348                 rt2x00_set_field32(&reg, ARCSR4_SERVICE, 0x04);
 349                 rt2x00_set_field32(&reg, ARCSR2_LENGTH,
 350                                    GET_DURATION(ACK_SIZE, 55));
 351                 rt2x00mmio_register_write(rt2x00dev, ARCSR4, reg);
 352 
 353                 reg = rt2x00mmio_register_read(rt2x00dev, ARCSR5);
 354                 rt2x00_set_field32(&reg, ARCSR5_SIGNAL, 0x03 | preamble_mask);
 355                 rt2x00_set_field32(&reg, ARCSR5_SERVICE, 0x84);
 356                 rt2x00_set_field32(&reg, ARCSR2_LENGTH,
 357                                    GET_DURATION(ACK_SIZE, 110));
 358                 rt2x00mmio_register_write(rt2x00dev, ARCSR5, reg);
 359         }
 360 
 361         if (changed & BSS_CHANGED_BASIC_RATES)
 362                 rt2x00mmio_register_write(rt2x00dev, ARCSR1, erp->basic_rates);
 363 
 364         if (changed & BSS_CHANGED_ERP_SLOT) {
 365                 reg = rt2x00mmio_register_read(rt2x00dev, CSR11);
 366                 rt2x00_set_field32(&reg, CSR11_SLOT_TIME, erp->slot_time);
 367                 rt2x00mmio_register_write(rt2x00dev, CSR11, reg);
 368 
 369                 reg = rt2x00mmio_register_read(rt2x00dev, CSR18);
 370                 rt2x00_set_field32(&reg, CSR18_SIFS, erp->sifs);
 371                 rt2x00_set_field32(&reg, CSR18_PIFS, erp->pifs);
 372                 rt2x00mmio_register_write(rt2x00dev, CSR18, reg);
 373 
 374                 reg = rt2x00mmio_register_read(rt2x00dev, CSR19);
 375                 rt2x00_set_field32(&reg, CSR19_DIFS, erp->difs);
 376                 rt2x00_set_field32(&reg, CSR19_EIFS, erp->eifs);
 377                 rt2x00mmio_register_write(rt2x00dev, CSR19, reg);
 378         }
 379 
 380         if (changed & BSS_CHANGED_BEACON_INT) {
 381                 reg = rt2x00mmio_register_read(rt2x00dev, CSR12);
 382                 rt2x00_set_field32(&reg, CSR12_BEACON_INTERVAL,
 383                                    erp->beacon_int * 16);
 384                 rt2x00_set_field32(&reg, CSR12_CFP_MAX_DURATION,
 385                                    erp->beacon_int * 16);
 386                 rt2x00mmio_register_write(rt2x00dev, CSR12, reg);
 387         }
 388 }
 389 
 390 static void rt2400pci_config_ant(struct rt2x00_dev *rt2x00dev,
 391                                  struct antenna_setup *ant)
 392 {
 393         u8 r1;
 394         u8 r4;
 395 
 396         /*
 397          * We should never come here because rt2x00lib is supposed
 398          * to catch this and send us the correct antenna explicitely.
 399          */
 400         BUG_ON(ant->rx == ANTENNA_SW_DIVERSITY ||
 401                ant->tx == ANTENNA_SW_DIVERSITY);
 402 
 403         r4 = rt2400pci_bbp_read(rt2x00dev, 4);
 404         r1 = rt2400pci_bbp_read(rt2x00dev, 1);
 405 
 406         /*
 407          * Configure the TX antenna.
 408          */
 409         switch (ant->tx) {
 410         case ANTENNA_HW_DIVERSITY:
 411                 rt2x00_set_field8(&r1, BBP_R1_TX_ANTENNA, 1);
 412                 break;
 413         case ANTENNA_A:
 414                 rt2x00_set_field8(&r1, BBP_R1_TX_ANTENNA, 0);
 415                 break;
 416         case ANTENNA_B:
 417         default:
 418                 rt2x00_set_field8(&r1, BBP_R1_TX_ANTENNA, 2);
 419                 break;
 420         }
 421 
 422         /*
 423          * Configure the RX antenna.
 424          */
 425         switch (ant->rx) {
 426         case ANTENNA_HW_DIVERSITY:
 427                 rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 1);
 428                 break;
 429         case ANTENNA_A:
 430                 rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 0);
 431                 break;
 432         case ANTENNA_B:
 433         default:
 434                 rt2x00_set_field8(&r4, BBP_R4_RX_ANTENNA, 2);
 435                 break;
 436         }
 437 
 438         rt2400pci_bbp_write(rt2x00dev, 4, r4);
 439         rt2400pci_bbp_write(rt2x00dev, 1, r1);
 440 }
 441 
 442 static void rt2400pci_config_channel(struct rt2x00_dev *rt2x00dev,
 443                                      struct rf_channel *rf)
 444 {
 445         /*
 446          * Switch on tuning bits.
 447          */
 448         rt2x00_set_field32(&rf->rf1, RF1_TUNER, 1);
 449         rt2x00_set_field32(&rf->rf3, RF3_TUNER, 1);
 450 
 451         rt2400pci_rf_write(rt2x00dev, 1, rf->rf1);
 452         rt2400pci_rf_write(rt2x00dev, 2, rf->rf2);
 453         rt2400pci_rf_write(rt2x00dev, 3, rf->rf3);
 454 
 455         /*
 456          * RF2420 chipset don't need any additional actions.
 457          */
 458         if (rt2x00_rf(rt2x00dev, RF2420))
 459                 return;
 460 
 461         /*
 462          * For the RT2421 chipsets we need to write an invalid
 463          * reference clock rate to activate auto_tune.
 464          * After that we set the value back to the correct channel.
 465          */
 466         rt2400pci_rf_write(rt2x00dev, 1, rf->rf1);
 467         rt2400pci_rf_write(rt2x00dev, 2, 0x000c2a32);
 468         rt2400pci_rf_write(rt2x00dev, 3, rf->rf3);
 469 
 470         msleep(1);
 471 
 472         rt2400pci_rf_write(rt2x00dev, 1, rf->rf1);
 473         rt2400pci_rf_write(rt2x00dev, 2, rf->rf2);
 474         rt2400pci_rf_write(rt2x00dev, 3, rf->rf3);
 475 
 476         msleep(1);
 477 
 478         /*
 479          * Switch off tuning bits.
 480          */
 481         rt2x00_set_field32(&rf->rf1, RF1_TUNER, 0);
 482         rt2x00_set_field32(&rf->rf3, RF3_TUNER, 0);
 483 
 484         rt2400pci_rf_write(rt2x00dev, 1, rf->rf1);
 485         rt2400pci_rf_write(rt2x00dev, 3, rf->rf3);
 486 
 487         /*
 488          * Clear false CRC during channel switch.
 489          */
 490         rf->rf1 = rt2x00mmio_register_read(rt2x00dev, CNT0);
 491 }
 492 
 493 static void rt2400pci_config_txpower(struct rt2x00_dev *rt2x00dev, int txpower)
 494 {
 495         rt2400pci_bbp_write(rt2x00dev, 3, TXPOWER_TO_DEV(txpower));
 496 }
 497 
 498 static void rt2400pci_config_retry_limit(struct rt2x00_dev *rt2x00dev,
 499                                          struct rt2x00lib_conf *libconf)
 500 {
 501         u32 reg;
 502 
 503         reg = rt2x00mmio_register_read(rt2x00dev, CSR11);
 504         rt2x00_set_field32(&reg, CSR11_LONG_RETRY,
 505                            libconf->conf->long_frame_max_tx_count);
 506         rt2x00_set_field32(&reg, CSR11_SHORT_RETRY,
 507                            libconf->conf->short_frame_max_tx_count);
 508         rt2x00mmio_register_write(rt2x00dev, CSR11, reg);
 509 }
 510 
 511 static void rt2400pci_config_ps(struct rt2x00_dev *rt2x00dev,
 512                                 struct rt2x00lib_conf *libconf)
 513 {
 514         enum dev_state state =
 515             (libconf->conf->flags & IEEE80211_CONF_PS) ?
 516                 STATE_SLEEP : STATE_AWAKE;
 517         u32 reg;
 518 
 519         if (state == STATE_SLEEP) {
 520                 reg = rt2x00mmio_register_read(rt2x00dev, CSR20);
 521                 rt2x00_set_field32(&reg, CSR20_DELAY_AFTER_TBCN,
 522                                    (rt2x00dev->beacon_int - 20) * 16);
 523                 rt2x00_set_field32(&reg, CSR20_TBCN_BEFORE_WAKEUP,
 524                                    libconf->conf->listen_interval - 1);
 525 
 526                 /* We must first disable autowake before it can be enabled */
 527                 rt2x00_set_field32(&reg, CSR20_AUTOWAKE, 0);
 528                 rt2x00mmio_register_write(rt2x00dev, CSR20, reg);
 529 
 530                 rt2x00_set_field32(&reg, CSR20_AUTOWAKE, 1);
 531                 rt2x00mmio_register_write(rt2x00dev, CSR20, reg);
 532         } else {
 533                 reg = rt2x00mmio_register_read(rt2x00dev, CSR20);
 534                 rt2x00_set_field32(&reg, CSR20_AUTOWAKE, 0);
 535                 rt2x00mmio_register_write(rt2x00dev, CSR20, reg);
 536         }
 537 
 538         rt2x00dev->ops->lib->set_device_state(rt2x00dev, state);
 539 }
 540 
 541 static void rt2400pci_config(struct rt2x00_dev *rt2x00dev,
 542                              struct rt2x00lib_conf *libconf,
 543                              const unsigned int flags)
 544 {
 545         if (flags & IEEE80211_CONF_CHANGE_CHANNEL)
 546                 rt2400pci_config_channel(rt2x00dev, &libconf->rf);
 547         if (flags & IEEE80211_CONF_CHANGE_POWER)
 548                 rt2400pci_config_txpower(rt2x00dev,
 549                                          libconf->conf->power_level);
 550         if (flags & IEEE80211_CONF_CHANGE_RETRY_LIMITS)
 551                 rt2400pci_config_retry_limit(rt2x00dev, libconf);
 552         if (flags & IEEE80211_CONF_CHANGE_PS)
 553                 rt2400pci_config_ps(rt2x00dev, libconf);
 554 }
 555 
 556 static void rt2400pci_config_cw(struct rt2x00_dev *rt2x00dev,
 557                                 const int cw_min, const int cw_max)
 558 {
 559         u32 reg;
 560 
 561         reg = rt2x00mmio_register_read(rt2x00dev, CSR11);
 562         rt2x00_set_field32(&reg, CSR11_CWMIN, cw_min);
 563         rt2x00_set_field32(&reg, CSR11_CWMAX, cw_max);
 564         rt2x00mmio_register_write(rt2x00dev, CSR11, reg);
 565 }
 566 
 567 /*
 568  * Link tuning
 569  */
 570 static void rt2400pci_link_stats(struct rt2x00_dev *rt2x00dev,
 571                                  struct link_qual *qual)
 572 {
 573         u32 reg;
 574         u8 bbp;
 575 
 576         /*
 577          * Update FCS error count from register.
 578          */
 579         reg = rt2x00mmio_register_read(rt2x00dev, CNT0);
 580         qual->rx_failed = rt2x00_get_field32(reg, CNT0_FCS_ERROR);
 581 
 582         /*
 583          * Update False CCA count from register.
 584          */
 585         bbp = rt2400pci_bbp_read(rt2x00dev, 39);
 586         qual->false_cca = bbp;
 587 }
 588 
 589 static inline void rt2400pci_set_vgc(struct rt2x00_dev *rt2x00dev,
 590                                      struct link_qual *qual, u8 vgc_level)
 591 {
 592         if (qual->vgc_level_reg != vgc_level) {
 593                 rt2400pci_bbp_write(rt2x00dev, 13, vgc_level);
 594                 qual->vgc_level = vgc_level;
 595                 qual->vgc_level_reg = vgc_level;
 596         }
 597 }
 598 
 599 static void rt2400pci_reset_tuner(struct rt2x00_dev *rt2x00dev,
 600                                   struct link_qual *qual)
 601 {
 602         rt2400pci_set_vgc(rt2x00dev, qual, 0x08);
 603 }
 604 
 605 static void rt2400pci_link_tuner(struct rt2x00_dev *rt2x00dev,
 606                                  struct link_qual *qual, const u32 count)
 607 {
 608         /*
 609          * The link tuner should not run longer then 60 seconds,
 610          * and should run once every 2 seconds.
 611          */
 612         if (count > 60 || !(count & 1))
 613                 return;
 614 
 615         /*
 616          * Base r13 link tuning on the false cca count.
 617          */
 618         if ((qual->false_cca > 512) && (qual->vgc_level < 0x20))
 619                 rt2400pci_set_vgc(rt2x00dev, qual, ++qual->vgc_level);
 620         else if ((qual->false_cca < 100) && (qual->vgc_level > 0x08))
 621                 rt2400pci_set_vgc(rt2x00dev, qual, --qual->vgc_level);
 622 }
 623 
 624 /*
 625  * Queue handlers.
 626  */
 627 static void rt2400pci_start_queue(struct data_queue *queue)
 628 {
 629         struct rt2x00_dev *rt2x00dev = queue->rt2x00dev;
 630         u32 reg;
 631 
 632         switch (queue->qid) {
 633         case QID_RX:
 634                 reg = rt2x00mmio_register_read(rt2x00dev, RXCSR0);
 635                 rt2x00_set_field32(&reg, RXCSR0_DISABLE_RX, 0);
 636                 rt2x00mmio_register_write(rt2x00dev, RXCSR0, reg);
 637                 break;
 638         case QID_BEACON:
 639                 reg = rt2x00mmio_register_read(rt2x00dev, CSR14);
 640                 rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 1);
 641                 rt2x00_set_field32(&reg, CSR14_TBCN, 1);
 642                 rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 1);
 643                 rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
 644                 break;
 645         default:
 646                 break;
 647         }
 648 }
 649 
 650 static void rt2400pci_kick_queue(struct data_queue *queue)
 651 {
 652         struct rt2x00_dev *rt2x00dev = queue->rt2x00dev;
 653         u32 reg;
 654 
 655         switch (queue->qid) {
 656         case QID_AC_VO:
 657                 reg = rt2x00mmio_register_read(rt2x00dev, TXCSR0);
 658                 rt2x00_set_field32(&reg, TXCSR0_KICK_PRIO, 1);
 659                 rt2x00mmio_register_write(rt2x00dev, TXCSR0, reg);
 660                 break;
 661         case QID_AC_VI:
 662                 reg = rt2x00mmio_register_read(rt2x00dev, TXCSR0);
 663                 rt2x00_set_field32(&reg, TXCSR0_KICK_TX, 1);
 664                 rt2x00mmio_register_write(rt2x00dev, TXCSR0, reg);
 665                 break;
 666         case QID_ATIM:
 667                 reg = rt2x00mmio_register_read(rt2x00dev, TXCSR0);
 668                 rt2x00_set_field32(&reg, TXCSR0_KICK_ATIM, 1);
 669                 rt2x00mmio_register_write(rt2x00dev, TXCSR0, reg);
 670                 break;
 671         default:
 672                 break;
 673         }
 674 }
 675 
 676 static void rt2400pci_stop_queue(struct data_queue *queue)
 677 {
 678         struct rt2x00_dev *rt2x00dev = queue->rt2x00dev;
 679         u32 reg;
 680 
 681         switch (queue->qid) {
 682         case QID_AC_VO:
 683         case QID_AC_VI:
 684         case QID_ATIM:
 685                 reg = rt2x00mmio_register_read(rt2x00dev, TXCSR0);
 686                 rt2x00_set_field32(&reg, TXCSR0_ABORT, 1);
 687                 rt2x00mmio_register_write(rt2x00dev, TXCSR0, reg);
 688                 break;
 689         case QID_RX:
 690                 reg = rt2x00mmio_register_read(rt2x00dev, RXCSR0);
 691                 rt2x00_set_field32(&reg, RXCSR0_DISABLE_RX, 1);
 692                 rt2x00mmio_register_write(rt2x00dev, RXCSR0, reg);
 693                 break;
 694         case QID_BEACON:
 695                 reg = rt2x00mmio_register_read(rt2x00dev, CSR14);
 696                 rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 0);
 697                 rt2x00_set_field32(&reg, CSR14_TBCN, 0);
 698                 rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
 699                 rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
 700 
 701                 /*
 702                  * Wait for possibly running tbtt tasklets.
 703                  */
 704                 tasklet_kill(&rt2x00dev->tbtt_tasklet);
 705                 break;
 706         default:
 707                 break;
 708         }
 709 }
 710 
 711 /*
 712  * Initialization functions.
 713  */
 714 static bool rt2400pci_get_entry_state(struct queue_entry *entry)
 715 {
 716         struct queue_entry_priv_mmio *entry_priv = entry->priv_data;
 717         u32 word;
 718 
 719         if (entry->queue->qid == QID_RX) {
 720                 word = rt2x00_desc_read(entry_priv->desc, 0);
 721 
 722                 return rt2x00_get_field32(word, RXD_W0_OWNER_NIC);
 723         } else {
 724                 word = rt2x00_desc_read(entry_priv->desc, 0);
 725 
 726                 return (rt2x00_get_field32(word, TXD_W0_OWNER_NIC) ||
 727                         rt2x00_get_field32(word, TXD_W0_VALID));
 728         }
 729 }
 730 
 731 static void rt2400pci_clear_entry(struct queue_entry *entry)
 732 {
 733         struct queue_entry_priv_mmio *entry_priv = entry->priv_data;
 734         struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
 735         u32 word;
 736 
 737         if (entry->queue->qid == QID_RX) {
 738                 word = rt2x00_desc_read(entry_priv->desc, 2);
 739                 rt2x00_set_field32(&word, RXD_W2_BUFFER_LENGTH, entry->skb->len);
 740                 rt2x00_desc_write(entry_priv->desc, 2, word);
 741 
 742                 word = rt2x00_desc_read(entry_priv->desc, 1);
 743                 rt2x00_set_field32(&word, RXD_W1_BUFFER_ADDRESS, skbdesc->skb_dma);
 744                 rt2x00_desc_write(entry_priv->desc, 1, word);
 745 
 746                 word = rt2x00_desc_read(entry_priv->desc, 0);
 747                 rt2x00_set_field32(&word, RXD_W0_OWNER_NIC, 1);
 748                 rt2x00_desc_write(entry_priv->desc, 0, word);
 749         } else {
 750                 word = rt2x00_desc_read(entry_priv->desc, 0);
 751                 rt2x00_set_field32(&word, TXD_W0_VALID, 0);
 752                 rt2x00_set_field32(&word, TXD_W0_OWNER_NIC, 0);
 753                 rt2x00_desc_write(entry_priv->desc, 0, word);
 754         }
 755 }
 756 
 757 static int rt2400pci_init_queues(struct rt2x00_dev *rt2x00dev)
 758 {
 759         struct queue_entry_priv_mmio *entry_priv;
 760         u32 reg;
 761 
 762         /*
 763          * Initialize registers.
 764          */
 765         reg = rt2x00mmio_register_read(rt2x00dev, TXCSR2);
 766         rt2x00_set_field32(&reg, TXCSR2_TXD_SIZE, rt2x00dev->tx[0].desc_size);
 767         rt2x00_set_field32(&reg, TXCSR2_NUM_TXD, rt2x00dev->tx[1].limit);
 768         rt2x00_set_field32(&reg, TXCSR2_NUM_ATIM, rt2x00dev->atim->limit);
 769         rt2x00_set_field32(&reg, TXCSR2_NUM_PRIO, rt2x00dev->tx[0].limit);
 770         rt2x00mmio_register_write(rt2x00dev, TXCSR2, reg);
 771 
 772         entry_priv = rt2x00dev->tx[1].entries[0].priv_data;
 773         reg = rt2x00mmio_register_read(rt2x00dev, TXCSR3);
 774         rt2x00_set_field32(&reg, TXCSR3_TX_RING_REGISTER,
 775                            entry_priv->desc_dma);
 776         rt2x00mmio_register_write(rt2x00dev, TXCSR3, reg);
 777 
 778         entry_priv = rt2x00dev->tx[0].entries[0].priv_data;
 779         reg = rt2x00mmio_register_read(rt2x00dev, TXCSR5);
 780         rt2x00_set_field32(&reg, TXCSR5_PRIO_RING_REGISTER,
 781                            entry_priv->desc_dma);
 782         rt2x00mmio_register_write(rt2x00dev, TXCSR5, reg);
 783 
 784         entry_priv = rt2x00dev->atim->entries[0].priv_data;
 785         reg = rt2x00mmio_register_read(rt2x00dev, TXCSR4);
 786         rt2x00_set_field32(&reg, TXCSR4_ATIM_RING_REGISTER,
 787                            entry_priv->desc_dma);
 788         rt2x00mmio_register_write(rt2x00dev, TXCSR4, reg);
 789 
 790         entry_priv = rt2x00dev->bcn->entries[0].priv_data;
 791         reg = rt2x00mmio_register_read(rt2x00dev, TXCSR6);
 792         rt2x00_set_field32(&reg, TXCSR6_BEACON_RING_REGISTER,
 793                            entry_priv->desc_dma);
 794         rt2x00mmio_register_write(rt2x00dev, TXCSR6, reg);
 795 
 796         reg = rt2x00mmio_register_read(rt2x00dev, RXCSR1);
 797         rt2x00_set_field32(&reg, RXCSR1_RXD_SIZE, rt2x00dev->rx->desc_size);
 798         rt2x00_set_field32(&reg, RXCSR1_NUM_RXD, rt2x00dev->rx->limit);
 799         rt2x00mmio_register_write(rt2x00dev, RXCSR1, reg);
 800 
 801         entry_priv = rt2x00dev->rx->entries[0].priv_data;
 802         reg = rt2x00mmio_register_read(rt2x00dev, RXCSR2);
 803         rt2x00_set_field32(&reg, RXCSR2_RX_RING_REGISTER,
 804                            entry_priv->desc_dma);
 805         rt2x00mmio_register_write(rt2x00dev, RXCSR2, reg);
 806 
 807         return 0;
 808 }
 809 
 810 static int rt2400pci_init_registers(struct rt2x00_dev *rt2x00dev)
 811 {
 812         u32 reg;
 813 
 814         rt2x00mmio_register_write(rt2x00dev, PSCSR0, 0x00020002);
 815         rt2x00mmio_register_write(rt2x00dev, PSCSR1, 0x00000002);
 816         rt2x00mmio_register_write(rt2x00dev, PSCSR2, 0x00023f20);
 817         rt2x00mmio_register_write(rt2x00dev, PSCSR3, 0x00000002);
 818 
 819         reg = rt2x00mmio_register_read(rt2x00dev, TIMECSR);
 820         rt2x00_set_field32(&reg, TIMECSR_US_COUNT, 33);
 821         rt2x00_set_field32(&reg, TIMECSR_US_64_COUNT, 63);
 822         rt2x00_set_field32(&reg, TIMECSR_BEACON_EXPECT, 0);
 823         rt2x00mmio_register_write(rt2x00dev, TIMECSR, reg);
 824 
 825         reg = rt2x00mmio_register_read(rt2x00dev, CSR9);
 826         rt2x00_set_field32(&reg, CSR9_MAX_FRAME_UNIT,
 827                            (rt2x00dev->rx->data_size / 128));
 828         rt2x00mmio_register_write(rt2x00dev, CSR9, reg);
 829 
 830         reg = rt2x00mmio_register_read(rt2x00dev, CSR14);
 831         rt2x00_set_field32(&reg, CSR14_TSF_COUNT, 0);
 832         rt2x00_set_field32(&reg, CSR14_TSF_SYNC, 0);
 833         rt2x00_set_field32(&reg, CSR14_TBCN, 0);
 834         rt2x00_set_field32(&reg, CSR14_TCFP, 0);
 835         rt2x00_set_field32(&reg, CSR14_TATIMW, 0);
 836         rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
 837         rt2x00_set_field32(&reg, CSR14_CFP_COUNT_PRELOAD, 0);
 838         rt2x00_set_field32(&reg, CSR14_TBCM_PRELOAD, 0);
 839         rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
 840 
 841         rt2x00mmio_register_write(rt2x00dev, CNT3, 0x3f080000);
 842 
 843         reg = rt2x00mmio_register_read(rt2x00dev, ARCSR0);
 844         rt2x00_set_field32(&reg, ARCSR0_AR_BBP_DATA0, 133);
 845         rt2x00_set_field32(&reg, ARCSR0_AR_BBP_ID0, 134);
 846         rt2x00_set_field32(&reg, ARCSR0_AR_BBP_DATA1, 136);
 847         rt2x00_set_field32(&reg, ARCSR0_AR_BBP_ID1, 135);
 848         rt2x00mmio_register_write(rt2x00dev, ARCSR0, reg);
 849 
 850         reg = rt2x00mmio_register_read(rt2x00dev, RXCSR3);
 851         rt2x00_set_field32(&reg, RXCSR3_BBP_ID0, 3); /* Tx power.*/
 852         rt2x00_set_field32(&reg, RXCSR3_BBP_ID0_VALID, 1);
 853         rt2x00_set_field32(&reg, RXCSR3_BBP_ID1, 32); /* Signal */
 854         rt2x00_set_field32(&reg, RXCSR3_BBP_ID1_VALID, 1);
 855         rt2x00_set_field32(&reg, RXCSR3_BBP_ID2, 36); /* Rssi */
 856         rt2x00_set_field32(&reg, RXCSR3_BBP_ID2_VALID, 1);
 857         rt2x00mmio_register_write(rt2x00dev, RXCSR3, reg);
 858 
 859         rt2x00mmio_register_write(rt2x00dev, PWRCSR0, 0x3f3b3100);
 860 
 861         if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE))
 862                 return -EBUSY;
 863 
 864         rt2x00mmio_register_write(rt2x00dev, MACCSR0, 0x00217223);
 865         rt2x00mmio_register_write(rt2x00dev, MACCSR1, 0x00235518);
 866 
 867         reg = rt2x00mmio_register_read(rt2x00dev, MACCSR2);
 868         rt2x00_set_field32(&reg, MACCSR2_DELAY, 64);
 869         rt2x00mmio_register_write(rt2x00dev, MACCSR2, reg);
 870 
 871         reg = rt2x00mmio_register_read(rt2x00dev, RALINKCSR);
 872         rt2x00_set_field32(&reg, RALINKCSR_AR_BBP_DATA0, 17);
 873         rt2x00_set_field32(&reg, RALINKCSR_AR_BBP_ID0, 154);
 874         rt2x00_set_field32(&reg, RALINKCSR_AR_BBP_DATA1, 0);
 875         rt2x00_set_field32(&reg, RALINKCSR_AR_BBP_ID1, 154);
 876         rt2x00mmio_register_write(rt2x00dev, RALINKCSR, reg);
 877 
 878         reg = rt2x00mmio_register_read(rt2x00dev, CSR1);
 879         rt2x00_set_field32(&reg, CSR1_SOFT_RESET, 1);
 880         rt2x00_set_field32(&reg, CSR1_BBP_RESET, 0);
 881         rt2x00_set_field32(&reg, CSR1_HOST_READY, 0);
 882         rt2x00mmio_register_write(rt2x00dev, CSR1, reg);
 883 
 884         reg = rt2x00mmio_register_read(rt2x00dev, CSR1);
 885         rt2x00_set_field32(&reg, CSR1_SOFT_RESET, 0);
 886         rt2x00_set_field32(&reg, CSR1_HOST_READY, 1);
 887         rt2x00mmio_register_write(rt2x00dev, CSR1, reg);
 888 
 889         /*
 890          * We must clear the FCS and FIFO error count.
 891          * These registers are cleared on read,
 892          * so we may pass a useless variable to store the value.
 893          */
 894         reg = rt2x00mmio_register_read(rt2x00dev, CNT0);
 895         reg = rt2x00mmio_register_read(rt2x00dev, CNT4);
 896 
 897         return 0;
 898 }
 899 
 900 static int rt2400pci_wait_bbp_ready(struct rt2x00_dev *rt2x00dev)
 901 {
 902         unsigned int i;
 903         u8 value;
 904 
 905         for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
 906                 value = rt2400pci_bbp_read(rt2x00dev, 0);
 907                 if ((value != 0xff) && (value != 0x00))
 908                         return 0;
 909                 udelay(REGISTER_BUSY_DELAY);
 910         }
 911 
 912         rt2x00_err(rt2x00dev, "BBP register access failed, aborting\n");
 913         return -EACCES;
 914 }
 915 
 916 static int rt2400pci_init_bbp(struct rt2x00_dev *rt2x00dev)
 917 {
 918         unsigned int i;
 919         u16 eeprom;
 920         u8 reg_id;
 921         u8 value;
 922 
 923         if (unlikely(rt2400pci_wait_bbp_ready(rt2x00dev)))
 924                 return -EACCES;
 925 
 926         rt2400pci_bbp_write(rt2x00dev, 1, 0x00);
 927         rt2400pci_bbp_write(rt2x00dev, 3, 0x27);
 928         rt2400pci_bbp_write(rt2x00dev, 4, 0x08);
 929         rt2400pci_bbp_write(rt2x00dev, 10, 0x0f);
 930         rt2400pci_bbp_write(rt2x00dev, 15, 0x72);
 931         rt2400pci_bbp_write(rt2x00dev, 16, 0x74);
 932         rt2400pci_bbp_write(rt2x00dev, 17, 0x20);
 933         rt2400pci_bbp_write(rt2x00dev, 18, 0x72);
 934         rt2400pci_bbp_write(rt2x00dev, 19, 0x0b);
 935         rt2400pci_bbp_write(rt2x00dev, 20, 0x00);
 936         rt2400pci_bbp_write(rt2x00dev, 28, 0x11);
 937         rt2400pci_bbp_write(rt2x00dev, 29, 0x04);
 938         rt2400pci_bbp_write(rt2x00dev, 30, 0x21);
 939         rt2400pci_bbp_write(rt2x00dev, 31, 0x00);
 940 
 941         for (i = 0; i < EEPROM_BBP_SIZE; i++) {
 942                 eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i);
 943 
 944                 if (eeprom != 0xffff && eeprom != 0x0000) {
 945                         reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID);
 946                         value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE);
 947                         rt2400pci_bbp_write(rt2x00dev, reg_id, value);
 948                 }
 949         }
 950 
 951         return 0;
 952 }
 953 
 954 /*
 955  * Device state switch handlers.
 956  */
 957 static void rt2400pci_toggle_irq(struct rt2x00_dev *rt2x00dev,
 958                                  enum dev_state state)
 959 {
 960         int mask = (state == STATE_RADIO_IRQ_OFF);
 961         u32 reg;
 962         unsigned long flags;
 963 
 964         /*
 965          * When interrupts are being enabled, the interrupt registers
 966          * should clear the register to assure a clean state.
 967          */
 968         if (state == STATE_RADIO_IRQ_ON) {
 969                 reg = rt2x00mmio_register_read(rt2x00dev, CSR7);
 970                 rt2x00mmio_register_write(rt2x00dev, CSR7, reg);
 971         }
 972 
 973         /*
 974          * Only toggle the interrupts bits we are going to use.
 975          * Non-checked interrupt bits are disabled by default.
 976          */
 977         spin_lock_irqsave(&rt2x00dev->irqmask_lock, flags);
 978 
 979         reg = rt2x00mmio_register_read(rt2x00dev, CSR8);
 980         rt2x00_set_field32(&reg, CSR8_TBCN_EXPIRE, mask);
 981         rt2x00_set_field32(&reg, CSR8_TXDONE_TXRING, mask);
 982         rt2x00_set_field32(&reg, CSR8_TXDONE_ATIMRING, mask);
 983         rt2x00_set_field32(&reg, CSR8_TXDONE_PRIORING, mask);
 984         rt2x00_set_field32(&reg, CSR8_RXDONE, mask);
 985         rt2x00mmio_register_write(rt2x00dev, CSR8, reg);
 986 
 987         spin_unlock_irqrestore(&rt2x00dev->irqmask_lock, flags);
 988 
 989         if (state == STATE_RADIO_IRQ_OFF) {
 990                 /*
 991                  * Ensure that all tasklets are finished before
 992                  * disabling the interrupts.
 993                  */
 994                 tasklet_kill(&rt2x00dev->txstatus_tasklet);
 995                 tasklet_kill(&rt2x00dev->rxdone_tasklet);
 996                 tasklet_kill(&rt2x00dev->tbtt_tasklet);
 997         }
 998 }
 999 
1000 static int rt2400pci_enable_radio(struct rt2x00_dev *rt2x00dev)
1001 {
1002         /*
1003          * Initialize all registers.
1004          */
1005         if (unlikely(rt2400pci_init_queues(rt2x00dev) ||
1006                      rt2400pci_init_registers(rt2x00dev) ||
1007                      rt2400pci_init_bbp(rt2x00dev)))
1008                 return -EIO;
1009 
1010         return 0;
1011 }
1012 
1013 static void rt2400pci_disable_radio(struct rt2x00_dev *rt2x00dev)
1014 {
1015         /*
1016          * Disable power
1017          */
1018         rt2x00mmio_register_write(rt2x00dev, PWRCSR0, 0);
1019 }
1020 
1021 static int rt2400pci_set_state(struct rt2x00_dev *rt2x00dev,
1022                                enum dev_state state)
1023 {
1024         u32 reg, reg2;
1025         unsigned int i;
1026         char put_to_sleep;
1027         char bbp_state;
1028         char rf_state;
1029 
1030         put_to_sleep = (state != STATE_AWAKE);
1031 
1032         reg = rt2x00mmio_register_read(rt2x00dev, PWRCSR1);
1033         rt2x00_set_field32(&reg, PWRCSR1_SET_STATE, 1);
1034         rt2x00_set_field32(&reg, PWRCSR1_BBP_DESIRE_STATE, state);
1035         rt2x00_set_field32(&reg, PWRCSR1_RF_DESIRE_STATE, state);
1036         rt2x00_set_field32(&reg, PWRCSR1_PUT_TO_SLEEP, put_to_sleep);
1037         rt2x00mmio_register_write(rt2x00dev, PWRCSR1, reg);
1038 
1039         /*
1040          * Device is not guaranteed to be in the requested state yet.
1041          * We must wait until the register indicates that the
1042          * device has entered the correct state.
1043          */
1044         for (i = 0; i < REGISTER_BUSY_COUNT; i++) {
1045                 reg2 = rt2x00mmio_register_read(rt2x00dev, PWRCSR1);
1046                 bbp_state = rt2x00_get_field32(reg2, PWRCSR1_BBP_CURR_STATE);
1047                 rf_state = rt2x00_get_field32(reg2, PWRCSR1_RF_CURR_STATE);
1048                 if (bbp_state == state && rf_state == state)
1049                         return 0;
1050                 rt2x00mmio_register_write(rt2x00dev, PWRCSR1, reg);
1051                 msleep(10);
1052         }
1053 
1054         return -EBUSY;
1055 }
1056 
1057 static int rt2400pci_set_device_state(struct rt2x00_dev *rt2x00dev,
1058                                       enum dev_state state)
1059 {
1060         int retval = 0;
1061 
1062         switch (state) {
1063         case STATE_RADIO_ON:
1064                 retval = rt2400pci_enable_radio(rt2x00dev);
1065                 break;
1066         case STATE_RADIO_OFF:
1067                 rt2400pci_disable_radio(rt2x00dev);
1068                 break;
1069         case STATE_RADIO_IRQ_ON:
1070         case STATE_RADIO_IRQ_OFF:
1071                 rt2400pci_toggle_irq(rt2x00dev, state);
1072                 break;
1073         case STATE_DEEP_SLEEP:
1074         case STATE_SLEEP:
1075         case STATE_STANDBY:
1076         case STATE_AWAKE:
1077                 retval = rt2400pci_set_state(rt2x00dev, state);
1078                 break;
1079         default:
1080                 retval = -ENOTSUPP;
1081                 break;
1082         }
1083 
1084         if (unlikely(retval))
1085                 rt2x00_err(rt2x00dev, "Device failed to enter state %d (%d)\n",
1086                            state, retval);
1087 
1088         return retval;
1089 }
1090 
1091 /*
1092  * TX descriptor initialization
1093  */
1094 static void rt2400pci_write_tx_desc(struct queue_entry *entry,
1095                                     struct txentry_desc *txdesc)
1096 {
1097         struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
1098         struct queue_entry_priv_mmio *entry_priv = entry->priv_data;
1099         __le32 *txd = entry_priv->desc;
1100         u32 word;
1101 
1102         /*
1103          * Start writing the descriptor words.
1104          */
1105         word = rt2x00_desc_read(txd, 1);
1106         rt2x00_set_field32(&word, TXD_W1_BUFFER_ADDRESS, skbdesc->skb_dma);
1107         rt2x00_desc_write(txd, 1, word);
1108 
1109         word = rt2x00_desc_read(txd, 2);
1110         rt2x00_set_field32(&word, TXD_W2_BUFFER_LENGTH, txdesc->length);
1111         rt2x00_set_field32(&word, TXD_W2_DATABYTE_COUNT, txdesc->length);
1112         rt2x00_desc_write(txd, 2, word);
1113 
1114         word = rt2x00_desc_read(txd, 3);
1115         rt2x00_set_field32(&word, TXD_W3_PLCP_SIGNAL, txdesc->u.plcp.signal);
1116         rt2x00_set_field32(&word, TXD_W3_PLCP_SIGNAL_REGNUM, 5);
1117         rt2x00_set_field32(&word, TXD_W3_PLCP_SIGNAL_BUSY, 1);
1118         rt2x00_set_field32(&word, TXD_W3_PLCP_SERVICE, txdesc->u.plcp.service);
1119         rt2x00_set_field32(&word, TXD_W3_PLCP_SERVICE_REGNUM, 6);
1120         rt2x00_set_field32(&word, TXD_W3_PLCP_SERVICE_BUSY, 1);
1121         rt2x00_desc_write(txd, 3, word);
1122 
1123         word = rt2x00_desc_read(txd, 4);
1124         rt2x00_set_field32(&word, TXD_W4_PLCP_LENGTH_LOW,
1125                            txdesc->u.plcp.length_low);
1126         rt2x00_set_field32(&word, TXD_W3_PLCP_LENGTH_LOW_REGNUM, 8);
1127         rt2x00_set_field32(&word, TXD_W3_PLCP_LENGTH_LOW_BUSY, 1);
1128         rt2x00_set_field32(&word, TXD_W4_PLCP_LENGTH_HIGH,
1129                            txdesc->u.plcp.length_high);
1130         rt2x00_set_field32(&word, TXD_W3_PLCP_LENGTH_HIGH_REGNUM, 7);
1131         rt2x00_set_field32(&word, TXD_W3_PLCP_LENGTH_HIGH_BUSY, 1);
1132         rt2x00_desc_write(txd, 4, word);
1133 
1134         /*
1135          * Writing TXD word 0 must the last to prevent a race condition with
1136          * the device, whereby the device may take hold of the TXD before we
1137          * finished updating it.
1138          */
1139         word = rt2x00_desc_read(txd, 0);
1140         rt2x00_set_field32(&word, TXD_W0_OWNER_NIC, 1);
1141         rt2x00_set_field32(&word, TXD_W0_VALID, 1);
1142         rt2x00_set_field32(&word, TXD_W0_MORE_FRAG,
1143                            test_bit(ENTRY_TXD_MORE_FRAG, &txdesc->flags));
1144         rt2x00_set_field32(&word, TXD_W0_ACK,
1145                            test_bit(ENTRY_TXD_ACK, &txdesc->flags));
1146         rt2x00_set_field32(&word, TXD_W0_TIMESTAMP,
1147                            test_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags));
1148         rt2x00_set_field32(&word, TXD_W0_RTS,
1149                            test_bit(ENTRY_TXD_RTS_FRAME, &txdesc->flags));
1150         rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->u.plcp.ifs);
1151         rt2x00_set_field32(&word, TXD_W0_RETRY_MODE,
1152                            test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags));
1153         rt2x00_desc_write(txd, 0, word);
1154 
1155         /*
1156          * Register descriptor details in skb frame descriptor.
1157          */
1158         skbdesc->desc = txd;
1159         skbdesc->desc_len = TXD_DESC_SIZE;
1160 }
1161 
1162 /*
1163  * TX data initialization
1164  */
1165 static void rt2400pci_write_beacon(struct queue_entry *entry,
1166                                    struct txentry_desc *txdesc)
1167 {
1168         struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
1169         u32 reg;
1170 
1171         /*
1172          * Disable beaconing while we are reloading the beacon data,
1173          * otherwise we might be sending out invalid data.
1174          */
1175         reg = rt2x00mmio_register_read(rt2x00dev, CSR14);
1176         rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 0);
1177         rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
1178 
1179         if (rt2x00queue_map_txskb(entry)) {
1180                 rt2x00_err(rt2x00dev, "Fail to map beacon, aborting\n");
1181                 goto out;
1182         }
1183         /*
1184          * Enable beaconing again.
1185          */
1186         rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 1);
1187         /*
1188          * Write the TX descriptor for the beacon.
1189          */
1190         rt2400pci_write_tx_desc(entry, txdesc);
1191 
1192         /*
1193          * Dump beacon to userspace through debugfs.
1194          */
1195         rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_BEACON, entry);
1196 out:
1197         /*
1198          * Enable beaconing again.
1199          */
1200         rt2x00_set_field32(&reg, CSR14_BEACON_GEN, 1);
1201         rt2x00mmio_register_write(rt2x00dev, CSR14, reg);
1202 }
1203 
1204 /*
1205  * RX control handlers
1206  */
1207 static void rt2400pci_fill_rxdone(struct queue_entry *entry,
1208                                   struct rxdone_entry_desc *rxdesc)
1209 {
1210         struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
1211         struct queue_entry_priv_mmio *entry_priv = entry->priv_data;
1212         u32 word0;
1213         u32 word2;
1214         u32 word3;
1215         u32 word4;
1216         u64 tsf;
1217         u32 rx_low;
1218         u32 rx_high;
1219 
1220         word0 = rt2x00_desc_read(entry_priv->desc, 0);
1221         word2 = rt2x00_desc_read(entry_priv->desc, 2);
1222         word3 = rt2x00_desc_read(entry_priv->desc, 3);
1223         word4 = rt2x00_desc_read(entry_priv->desc, 4);
1224 
1225         if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR))
1226                 rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC;
1227         if (rt2x00_get_field32(word0, RXD_W0_PHYSICAL_ERROR))
1228                 rxdesc->flags |= RX_FLAG_FAILED_PLCP_CRC;
1229 
1230         /*
1231          * We only get the lower 32bits from the timestamp,
1232          * to get the full 64bits we must complement it with
1233          * the timestamp from get_tsf().
1234          * Note that when a wraparound of the lower 32bits
1235          * has occurred between the frame arrival and the get_tsf()
1236          * call, we must decrease the higher 32bits with 1 to get
1237          * to correct value.
1238          */
1239         tsf = rt2x00dev->ops->hw->get_tsf(rt2x00dev->hw, NULL);
1240         rx_low = rt2x00_get_field32(word4, RXD_W4_RX_END_TIME);
1241         rx_high = upper_32_bits(tsf);
1242 
1243         if ((u32)tsf <= rx_low)
1244                 rx_high--;
1245 
1246         /*
1247          * Obtain the status about this packet.
1248          * The signal is the PLCP value, and needs to be stripped
1249          * of the preamble bit (0x08).
1250          */
1251         rxdesc->timestamp = ((u64)rx_high << 32) | rx_low;
1252         rxdesc->signal = rt2x00_get_field32(word2, RXD_W2_SIGNAL) & ~0x08;
1253         rxdesc->rssi = rt2x00_get_field32(word3, RXD_W3_RSSI) -
1254             entry->queue->rt2x00dev->rssi_offset;
1255         rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT);
1256 
1257         rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP;
1258         if (rt2x00_get_field32(word0, RXD_W0_MY_BSS))
1259                 rxdesc->dev_flags |= RXDONE_MY_BSS;
1260 }
1261 
1262 /*
1263  * Interrupt functions.
1264  */
1265 static void rt2400pci_txdone(struct rt2x00_dev *rt2x00dev,
1266                              const enum data_queue_qid queue_idx)
1267 {
1268         struct data_queue *queue = rt2x00queue_get_tx_queue(rt2x00dev, queue_idx);
1269         struct queue_entry_priv_mmio *entry_priv;
1270         struct queue_entry *entry;
1271         struct txdone_entry_desc txdesc;
1272         u32 word;
1273 
1274         while (!rt2x00queue_empty(queue)) {
1275                 entry = rt2x00queue_get_entry(queue, Q_INDEX_DONE);
1276                 entry_priv = entry->priv_data;
1277                 word = rt2x00_desc_read(entry_priv->desc, 0);
1278 
1279                 if (rt2x00_get_field32(word, TXD_W0_OWNER_NIC) ||
1280                     !rt2x00_get_field32(word, TXD_W0_VALID))
1281                         break;
1282 
1283                 /*
1284                  * Obtain the status about this packet.
1285                  */
1286                 txdesc.flags = 0;
1287                 switch (rt2x00_get_field32(word, TXD_W0_RESULT)) {
1288                 case 0: /* Success */
1289                 case 1: /* Success with retry */
1290                         __set_bit(TXDONE_SUCCESS, &txdesc.flags);
1291                         break;
1292                 case 2: /* Failure, excessive retries */
1293                         __set_bit(TXDONE_EXCESSIVE_RETRY, &txdesc.flags);
1294                         /* Fall through - this is a failed frame! */
1295                 default: /* Failure */
1296                         __set_bit(TXDONE_FAILURE, &txdesc.flags);
1297                 }
1298                 txdesc.retry = rt2x00_get_field32(word, TXD_W0_RETRY_COUNT);
1299 
1300                 rt2x00lib_txdone(entry, &txdesc);
1301         }
1302 }
1303 
1304 static inline void rt2400pci_enable_interrupt(struct rt2x00_dev *rt2x00dev,
1305                                               struct rt2x00_field32 irq_field)
1306 {
1307         u32 reg;
1308 
1309         /*
1310          * Enable a single interrupt. The interrupt mask register
1311          * access needs locking.
1312          */
1313         spin_lock_irq(&rt2x00dev->irqmask_lock);
1314 
1315         reg = rt2x00mmio_register_read(rt2x00dev, CSR8);
1316         rt2x00_set_field32(&reg, irq_field, 0);
1317         rt2x00mmio_register_write(rt2x00dev, CSR8, reg);
1318 
1319         spin_unlock_irq(&rt2x00dev->irqmask_lock);
1320 }
1321 
1322 static void rt2400pci_txstatus_tasklet(unsigned long data)
1323 {
1324         struct rt2x00_dev *rt2x00dev = (struct rt2x00_dev *)data;
1325         u32 reg;
1326 
1327         /*
1328          * Handle all tx queues.
1329          */
1330         rt2400pci_txdone(rt2x00dev, QID_ATIM);
1331         rt2400pci_txdone(rt2x00dev, QID_AC_VO);
1332         rt2400pci_txdone(rt2x00dev, QID_AC_VI);
1333 
1334         /*
1335          * Enable all TXDONE interrupts again.
1336          */
1337         if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) {
1338                 spin_lock_irq(&rt2x00dev->irqmask_lock);
1339 
1340                 reg = rt2x00mmio_register_read(rt2x00dev, CSR8);
1341                 rt2x00_set_field32(&reg, CSR8_TXDONE_TXRING, 0);
1342                 rt2x00_set_field32(&reg, CSR8_TXDONE_ATIMRING, 0);
1343                 rt2x00_set_field32(&reg, CSR8_TXDONE_PRIORING, 0);
1344                 rt2x00mmio_register_write(rt2x00dev, CSR8, reg);
1345 
1346                 spin_unlock_irq(&rt2x00dev->irqmask_lock);
1347         }
1348 }
1349 
1350 static void rt2400pci_tbtt_tasklet(unsigned long data)
1351 {
1352         struct rt2x00_dev *rt2x00dev = (struct rt2x00_dev *)data;
1353         rt2x00lib_beacondone(rt2x00dev);
1354         if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
1355                 rt2400pci_enable_interrupt(rt2x00dev, CSR8_TBCN_EXPIRE);
1356 }
1357 
1358 static void rt2400pci_rxdone_tasklet(unsigned long data)
1359 {
1360         struct rt2x00_dev *rt2x00dev = (struct rt2x00_dev *)data;
1361         if (rt2x00mmio_rxdone(rt2x00dev))
1362                 tasklet_schedule(&rt2x00dev->rxdone_tasklet);
1363         else if (test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
1364                 rt2400pci_enable_interrupt(rt2x00dev, CSR8_RXDONE);
1365 }
1366 
1367 static irqreturn_t rt2400pci_interrupt(int irq, void *dev_instance)
1368 {
1369         struct rt2x00_dev *rt2x00dev = dev_instance;
1370         u32 reg, mask;
1371 
1372         /*
1373          * Get the interrupt sources & saved to local variable.
1374          * Write register value back to clear pending interrupts.
1375          */
1376         reg = rt2x00mmio_register_read(rt2x00dev, CSR7);
1377         rt2x00mmio_register_write(rt2x00dev, CSR7, reg);
1378 
1379         if (!reg)
1380                 return IRQ_NONE;
1381 
1382         if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
1383                 return IRQ_HANDLED;
1384 
1385         mask = reg;
1386 
1387         /*
1388          * Schedule tasklets for interrupt handling.
1389          */
1390         if (rt2x00_get_field32(reg, CSR7_TBCN_EXPIRE))
1391                 tasklet_hi_schedule(&rt2x00dev->tbtt_tasklet);
1392 
1393         if (rt2x00_get_field32(reg, CSR7_RXDONE))
1394                 tasklet_schedule(&rt2x00dev->rxdone_tasklet);
1395 
1396         if (rt2x00_get_field32(reg, CSR7_TXDONE_ATIMRING) ||
1397             rt2x00_get_field32(reg, CSR7_TXDONE_PRIORING) ||
1398             rt2x00_get_field32(reg, CSR7_TXDONE_TXRING)) {
1399                 tasklet_schedule(&rt2x00dev->txstatus_tasklet);
1400                 /*
1401                  * Mask out all txdone interrupts.
1402                  */
1403                 rt2x00_set_field32(&mask, CSR8_TXDONE_TXRING, 1);
1404                 rt2x00_set_field32(&mask, CSR8_TXDONE_ATIMRING, 1);
1405                 rt2x00_set_field32(&mask, CSR8_TXDONE_PRIORING, 1);
1406         }
1407 
1408         /*
1409          * Disable all interrupts for which a tasklet was scheduled right now,
1410          * the tasklet will reenable the appropriate interrupts.
1411          */
1412         spin_lock(&rt2x00dev->irqmask_lock);
1413 
1414         reg = rt2x00mmio_register_read(rt2x00dev, CSR8);
1415         reg |= mask;
1416         rt2x00mmio_register_write(rt2x00dev, CSR8, reg);
1417 
1418         spin_unlock(&rt2x00dev->irqmask_lock);
1419 
1420 
1421 
1422         return IRQ_HANDLED;
1423 }
1424 
1425 /*
1426  * Device probe functions.
1427  */
1428 static int rt2400pci_validate_eeprom(struct rt2x00_dev *rt2x00dev)
1429 {
1430         struct eeprom_93cx6 eeprom;
1431         u32 reg;
1432         u16 word;
1433         u8 *mac;
1434 
1435         reg = rt2x00mmio_register_read(rt2x00dev, CSR21);
1436 
1437         eeprom.data = rt2x00dev;
1438         eeprom.register_read = rt2400pci_eepromregister_read;
1439         eeprom.register_write = rt2400pci_eepromregister_write;
1440         eeprom.width = rt2x00_get_field32(reg, CSR21_TYPE_93C46) ?
1441             PCI_EEPROM_WIDTH_93C46 : PCI_EEPROM_WIDTH_93C66;
1442         eeprom.reg_data_in = 0;
1443         eeprom.reg_data_out = 0;
1444         eeprom.reg_data_clock = 0;
1445         eeprom.reg_chip_select = 0;
1446 
1447         eeprom_93cx6_multiread(&eeprom, EEPROM_BASE, rt2x00dev->eeprom,
1448                                EEPROM_SIZE / sizeof(u16));
1449 
1450         /*
1451          * Start validation of the data that has been read.
1452          */
1453         mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0);
1454         rt2x00lib_set_mac_address(rt2x00dev, mac);
1455 
1456         word = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA);
1457         if (word == 0xffff) {
1458                 rt2x00_err(rt2x00dev, "Invalid EEPROM data detected\n");
1459                 return -EINVAL;
1460         }
1461 
1462         return 0;
1463 }
1464 
1465 static int rt2400pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
1466 {
1467         u32 reg;
1468         u16 value;
1469         u16 eeprom;
1470 
1471         /*
1472          * Read EEPROM word for configuration.
1473          */
1474         eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA);
1475 
1476         /*
1477          * Identify RF chipset.
1478          */
1479         value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE);
1480         reg = rt2x00mmio_register_read(rt2x00dev, CSR0);
1481         rt2x00_set_chip(rt2x00dev, RT2460, value,
1482                         rt2x00_get_field32(reg, CSR0_REVISION));
1483 
1484         if (!rt2x00_rf(rt2x00dev, RF2420) && !rt2x00_rf(rt2x00dev, RF2421)) {
1485                 rt2x00_err(rt2x00dev, "Invalid RF chipset detected\n");
1486                 return -ENODEV;
1487         }
1488 
1489         /*
1490          * Identify default antenna configuration.
1491          */
1492         rt2x00dev->default_ant.tx =
1493             rt2x00_get_field16(eeprom, EEPROM_ANTENNA_TX_DEFAULT);
1494         rt2x00dev->default_ant.rx =
1495             rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_DEFAULT);
1496 
1497         /*
1498          * When the eeprom indicates SW_DIVERSITY use HW_DIVERSITY instead.
1499          * I am not 100% sure about this, but the legacy drivers do not
1500          * indicate antenna swapping in software is required when
1501          * diversity is enabled.
1502          */
1503         if (rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY)
1504                 rt2x00dev->default_ant.tx = ANTENNA_HW_DIVERSITY;
1505         if (rt2x00dev->default_ant.rx == ANTENNA_SW_DIVERSITY)
1506                 rt2x00dev->default_ant.rx = ANTENNA_HW_DIVERSITY;
1507 
1508         /*
1509          * Store led mode, for correct led behaviour.
1510          */
1511 #ifdef CONFIG_RT2X00_LIB_LEDS
1512         value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_LED_MODE);
1513 
1514         rt2400pci_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO);
1515         if (value == LED_MODE_TXRX_ACTIVITY ||
1516             value == LED_MODE_DEFAULT ||
1517             value == LED_MODE_ASUS)
1518                 rt2400pci_init_led(rt2x00dev, &rt2x00dev->led_qual,
1519                                    LED_TYPE_ACTIVITY);
1520 #endif /* CONFIG_RT2X00_LIB_LEDS */
1521 
1522         /*
1523          * Detect if this device has an hardware controlled radio.
1524          */
1525         if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO))
1526                 __set_bit(CAPABILITY_HW_BUTTON, &rt2x00dev->cap_flags);
1527 
1528         /*
1529          * Check if the BBP tuning should be enabled.
1530          */
1531         if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_AGCVGC_TUNING))
1532                 __set_bit(CAPABILITY_LINK_TUNING, &rt2x00dev->cap_flags);
1533 
1534         return 0;
1535 }
1536 
1537 /*
1538  * RF value list for RF2420 & RF2421
1539  * Supports: 2.4 GHz
1540  */
1541 static const struct rf_channel rf_vals_b[] = {
1542         { 1,  0x00022058, 0x000c1fda, 0x00000101, 0 },
1543         { 2,  0x00022058, 0x000c1fee, 0x00000101, 0 },
1544         { 3,  0x00022058, 0x000c2002, 0x00000101, 0 },
1545         { 4,  0x00022058, 0x000c2016, 0x00000101, 0 },
1546         { 5,  0x00022058, 0x000c202a, 0x00000101, 0 },
1547         { 6,  0x00022058, 0x000c203e, 0x00000101, 0 },
1548         { 7,  0x00022058, 0x000c2052, 0x00000101, 0 },
1549         { 8,  0x00022058, 0x000c2066, 0x00000101, 0 },
1550         { 9,  0x00022058, 0x000c207a, 0x00000101, 0 },
1551         { 10, 0x00022058, 0x000c208e, 0x00000101, 0 },
1552         { 11, 0x00022058, 0x000c20a2, 0x00000101, 0 },
1553         { 12, 0x00022058, 0x000c20b6, 0x00000101, 0 },
1554         { 13, 0x00022058, 0x000c20ca, 0x00000101, 0 },
1555         { 14, 0x00022058, 0x000c20fa, 0x00000101, 0 },
1556 };
1557 
1558 static int rt2400pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
1559 {
1560         struct hw_mode_spec *spec = &rt2x00dev->spec;
1561         struct channel_info *info;
1562         char *tx_power;
1563         unsigned int i;
1564 
1565         /*
1566          * Initialize all hw fields.
1567          */
1568         ieee80211_hw_set(rt2x00dev->hw, PS_NULLFUNC_STACK);
1569         ieee80211_hw_set(rt2x00dev->hw, SUPPORTS_PS);
1570         ieee80211_hw_set(rt2x00dev->hw, HOST_BROADCAST_PS_BUFFERING);
1571         ieee80211_hw_set(rt2x00dev->hw, SIGNAL_DBM);
1572 
1573         SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev);
1574         SET_IEEE80211_PERM_ADDR(rt2x00dev->hw,
1575                                 rt2x00_eeprom_addr(rt2x00dev,
1576                                                    EEPROM_MAC_ADDR_0));
1577 
1578         /*
1579          * Initialize hw_mode information.
1580          */
1581         spec->supported_bands = SUPPORT_BAND_2GHZ;
1582         spec->supported_rates = SUPPORT_RATE_CCK;
1583 
1584         spec->num_channels = ARRAY_SIZE(rf_vals_b);
1585         spec->channels = rf_vals_b;
1586 
1587         /*
1588          * Create channel information array
1589          */
1590         info = kcalloc(spec->num_channels, sizeof(*info), GFP_KERNEL);
1591         if (!info)
1592                 return -ENOMEM;
1593 
1594         spec->channels_info = info;
1595 
1596         tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_START);
1597         for (i = 0; i < 14; i++) {
1598                 info[i].max_power = TXPOWER_FROM_DEV(MAX_TXPOWER);
1599                 info[i].default_power1 = TXPOWER_FROM_DEV(tx_power[i]);
1600         }
1601 
1602         return 0;
1603 }
1604 
1605 static int rt2400pci_probe_hw(struct rt2x00_dev *rt2x00dev)
1606 {
1607         int retval;
1608         u32 reg;
1609 
1610         /*
1611          * Allocate eeprom data.
1612          */
1613         retval = rt2400pci_validate_eeprom(rt2x00dev);
1614         if (retval)
1615                 return retval;
1616 
1617         retval = rt2400pci_init_eeprom(rt2x00dev);
1618         if (retval)
1619                 return retval;
1620 
1621         /*
1622          * Enable rfkill polling by setting GPIO direction of the
1623          * rfkill switch GPIO pin correctly.
1624          */
1625         reg = rt2x00mmio_register_read(rt2x00dev, GPIOCSR);
1626         rt2x00_set_field32(&reg, GPIOCSR_DIR0, 1);
1627         rt2x00mmio_register_write(rt2x00dev, GPIOCSR, reg);
1628 
1629         /*
1630          * Initialize hw specifications.
1631          */
1632         retval = rt2400pci_probe_hw_mode(rt2x00dev);
1633         if (retval)
1634                 return retval;
1635 
1636         /*
1637          * This device requires the atim queue and DMA-mapped skbs.
1638          */
1639         __set_bit(REQUIRE_ATIM_QUEUE, &rt2x00dev->cap_flags);
1640         __set_bit(REQUIRE_DMA, &rt2x00dev->cap_flags);
1641         __set_bit(REQUIRE_SW_SEQNO, &rt2x00dev->cap_flags);
1642 
1643         /*
1644          * Set the rssi offset.
1645          */
1646         rt2x00dev->rssi_offset = DEFAULT_RSSI_OFFSET;
1647 
1648         return 0;
1649 }
1650 
1651 /*
1652  * IEEE80211 stack callback functions.
1653  */
1654 static int rt2400pci_conf_tx(struct ieee80211_hw *hw,
1655                              struct ieee80211_vif *vif, u16 queue,
1656                              const struct ieee80211_tx_queue_params *params)
1657 {
1658         struct rt2x00_dev *rt2x00dev = hw->priv;
1659 
1660         /*
1661          * We don't support variating cw_min and cw_max variables
1662          * per queue. So by default we only configure the TX queue,
1663          * and ignore all other configurations.
1664          */
1665         if (queue != 0)
1666                 return -EINVAL;
1667 
1668         if (rt2x00mac_conf_tx(hw, vif, queue, params))
1669                 return -EINVAL;
1670 
1671         /*
1672          * Write configuration to register.
1673          */
1674         rt2400pci_config_cw(rt2x00dev,
1675                             rt2x00dev->tx->cw_min, rt2x00dev->tx->cw_max);
1676 
1677         return 0;
1678 }
1679 
1680 static u64 rt2400pci_get_tsf(struct ieee80211_hw *hw,
1681                              struct ieee80211_vif *vif)
1682 {
1683         struct rt2x00_dev *rt2x00dev = hw->priv;
1684         u64 tsf;
1685         u32 reg;
1686 
1687         reg = rt2x00mmio_register_read(rt2x00dev, CSR17);
1688         tsf = (u64) rt2x00_get_field32(reg, CSR17_HIGH_TSFTIMER) << 32;
1689         reg = rt2x00mmio_register_read(rt2x00dev, CSR16);
1690         tsf |= rt2x00_get_field32(reg, CSR16_LOW_TSFTIMER);
1691 
1692         return tsf;
1693 }
1694 
1695 static int rt2400pci_tx_last_beacon(struct ieee80211_hw *hw)
1696 {
1697         struct rt2x00_dev *rt2x00dev = hw->priv;
1698         u32 reg;
1699 
1700         reg = rt2x00mmio_register_read(rt2x00dev, CSR15);
1701         return rt2x00_get_field32(reg, CSR15_BEACON_SENT);
1702 }
1703 
1704 static const struct ieee80211_ops rt2400pci_mac80211_ops = {
1705         .tx                     = rt2x00mac_tx,
1706         .start                  = rt2x00mac_start,
1707         .stop                   = rt2x00mac_stop,
1708         .add_interface          = rt2x00mac_add_interface,
1709         .remove_interface       = rt2x00mac_remove_interface,
1710         .config                 = rt2x00mac_config,
1711         .configure_filter       = rt2x00mac_configure_filter,
1712         .sw_scan_start          = rt2x00mac_sw_scan_start,
1713         .sw_scan_complete       = rt2x00mac_sw_scan_complete,
1714         .get_stats              = rt2x00mac_get_stats,
1715         .bss_info_changed       = rt2x00mac_bss_info_changed,
1716         .conf_tx                = rt2400pci_conf_tx,
1717         .get_tsf                = rt2400pci_get_tsf,
1718         .tx_last_beacon         = rt2400pci_tx_last_beacon,
1719         .rfkill_poll            = rt2x00mac_rfkill_poll,
1720         .flush                  = rt2x00mac_flush,
1721         .set_antenna            = rt2x00mac_set_antenna,
1722         .get_antenna            = rt2x00mac_get_antenna,
1723         .get_ringparam          = rt2x00mac_get_ringparam,
1724         .tx_frames_pending      = rt2x00mac_tx_frames_pending,
1725 };
1726 
1727 static const struct rt2x00lib_ops rt2400pci_rt2x00_ops = {
1728         .irq_handler            = rt2400pci_interrupt,
1729         .txstatus_tasklet       = rt2400pci_txstatus_tasklet,
1730         .tbtt_tasklet           = rt2400pci_tbtt_tasklet,
1731         .rxdone_tasklet         = rt2400pci_rxdone_tasklet,
1732         .probe_hw               = rt2400pci_probe_hw,
1733         .initialize             = rt2x00mmio_initialize,
1734         .uninitialize           = rt2x00mmio_uninitialize,
1735         .get_entry_state        = rt2400pci_get_entry_state,
1736         .clear_entry            = rt2400pci_clear_entry,
1737         .set_device_state       = rt2400pci_set_device_state,
1738         .rfkill_poll            = rt2400pci_rfkill_poll,
1739         .link_stats             = rt2400pci_link_stats,
1740         .reset_tuner            = rt2400pci_reset_tuner,
1741         .link_tuner             = rt2400pci_link_tuner,
1742         .start_queue            = rt2400pci_start_queue,
1743         .kick_queue             = rt2400pci_kick_queue,
1744         .stop_queue             = rt2400pci_stop_queue,
1745         .flush_queue            = rt2x00mmio_flush_queue,
1746         .write_tx_desc          = rt2400pci_write_tx_desc,
1747         .write_beacon           = rt2400pci_write_beacon,
1748         .fill_rxdone            = rt2400pci_fill_rxdone,
1749         .config_filter          = rt2400pci_config_filter,
1750         .config_intf            = rt2400pci_config_intf,
1751         .config_erp             = rt2400pci_config_erp,
1752         .config_ant             = rt2400pci_config_ant,
1753         .config                 = rt2400pci_config,
1754 };
1755 
1756 static void rt2400pci_queue_init(struct data_queue *queue)
1757 {
1758         switch (queue->qid) {
1759         case QID_RX:
1760                 queue->limit = 24;
1761                 queue->data_size = DATA_FRAME_SIZE;
1762                 queue->desc_size = RXD_DESC_SIZE;
1763                 queue->priv_size = sizeof(struct queue_entry_priv_mmio);
1764                 break;
1765 
1766         case QID_AC_VO:
1767         case QID_AC_VI:
1768         case QID_AC_BE:
1769         case QID_AC_BK:
1770                 queue->limit = 24;
1771                 queue->data_size = DATA_FRAME_SIZE;
1772                 queue->desc_size = TXD_DESC_SIZE;
1773                 queue->priv_size = sizeof(struct queue_entry_priv_mmio);
1774                 break;
1775 
1776         case QID_BEACON:
1777                 queue->limit = 1;
1778                 queue->data_size = MGMT_FRAME_SIZE;
1779                 queue->desc_size = TXD_DESC_SIZE;
1780                 queue->priv_size = sizeof(struct queue_entry_priv_mmio);
1781                 break;
1782 
1783         case QID_ATIM:
1784                 queue->limit = 8;
1785                 queue->data_size = DATA_FRAME_SIZE;
1786                 queue->desc_size = TXD_DESC_SIZE;
1787                 queue->priv_size = sizeof(struct queue_entry_priv_mmio);
1788                 break;
1789 
1790         default:
1791                 BUG();
1792                 break;
1793         }
1794 }
1795 
1796 static const struct rt2x00_ops rt2400pci_ops = {
1797         .name                   = KBUILD_MODNAME,
1798         .max_ap_intf            = 1,
1799         .eeprom_size            = EEPROM_SIZE,
1800         .rf_size                = RF_SIZE,
1801         .tx_queues              = NUM_TX_QUEUES,
1802         .queue_init             = rt2400pci_queue_init,
1803         .lib                    = &rt2400pci_rt2x00_ops,
1804         .hw                     = &rt2400pci_mac80211_ops,
1805 #ifdef CONFIG_RT2X00_LIB_DEBUGFS
1806         .debugfs                = &rt2400pci_rt2x00debug,
1807 #endif /* CONFIG_RT2X00_LIB_DEBUGFS */
1808 };
1809 
1810 /*
1811  * RT2400pci module information.
1812  */
1813 static const struct pci_device_id rt2400pci_device_table[] = {
1814         { PCI_DEVICE(0x1814, 0x0101) },
1815         { 0, }
1816 };
1817 
1818 
1819 MODULE_AUTHOR(DRV_PROJECT);
1820 MODULE_VERSION(DRV_VERSION);
1821 MODULE_DESCRIPTION("Ralink RT2400 PCI & PCMCIA Wireless LAN driver.");
1822 MODULE_SUPPORTED_DEVICE("Ralink RT2460 PCI & PCMCIA chipset based cards");
1823 MODULE_DEVICE_TABLE(pci, rt2400pci_device_table);
1824 MODULE_LICENSE("GPL");
1825 
1826 static int rt2400pci_probe(struct pci_dev *pci_dev,
1827                            const struct pci_device_id *id)
1828 {
1829         return rt2x00pci_probe(pci_dev, &rt2400pci_ops);
1830 }
1831 
1832 static struct pci_driver rt2400pci_driver = {
1833         .name           = KBUILD_MODNAME,
1834         .id_table       = rt2400pci_device_table,
1835         .probe          = rt2400pci_probe,
1836         .remove         = rt2x00pci_remove,
1837         .suspend        = rt2x00pci_suspend,
1838         .resume         = rt2x00pci_resume,
1839 };
1840 
1841 module_pci_driver(rt2400pci_driver);
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/net/wireless/ralink/rt2x00/rt2400pci.c

DEFINITIONS
