drivers/net/wireless/realtek/rtlwifi/rtl8723ae/pwrseq.h

/* [<][>][^][v][top][bottom][index][help] */
   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 /* Copyright(c) 2009-2012  Realtek Corporation.*/
   3 
   4 #ifndef __RTL8723E_PWRSEQ_H__
   5 #define __RTL8723E_PWRSEQ_H__
   6 
   7 #include "../pwrseqcmd.h"
   8 /*
   9  *      Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd
  10  *      There are 6 HW Power States:
  11  *      0: POFF--Power Off
  12  *      1: PDN--Power Down
  13  *      2: CARDEMU--Card Emulation
  14  *      3: ACT--Active Mode
  15  *      4: LPS--Low Power State
  16  *      5: SUS--Suspend
  17  *
  18  *      The transision from different states are defined below
  19  *      TRANS_CARDEMU_TO_ACT
  20  *      TRANS_ACT_TO_CARDEMU
  21  *      TRANS_CARDEMU_TO_SUS
  22  *      TRANS_SUS_TO_CARDEMU
  23  *      TRANS_CARDEMU_TO_PDN
  24  *      TRANS_ACT_TO_LPS
  25  *      TRANS_LPS_TO_ACT
  26  *
  27  *      TRANS_END
  28  */
  29 
  30 #define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS     10
  31 #define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS     10
  32 #define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS     10
  33 #define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS     10
  34 #define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS     10
  35 #define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS     10
  36 #define RTL8723A_TRANS_ACT_TO_LPS_STEPS         15
  37 #define RTL8723A_TRANS_LPS_TO_ACT_STEPS         15
  38 #define RTL8723A_TRANS_END_STEPS                1
  39 
  40 /* format */
  41 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }*/
  42 
  43 #define RTL8723A_TRANS_CARDEMU_TO_ACT   \
  44         /* disable SW LPS 0x04[10]=0*/  \
  45         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  46                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},\
  47         /* wait till 0x04[17] = 1    power ready*/      \
  48         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  49                 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},\
  50         /* release WLON reset  0x04[16]=1*/     \
  51         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  52                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\
  53         /* disable HWPDN 0x04[15]=0*/ \
  54         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  55                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\
  56         /* disable WL suspend*/ \
  57         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  58                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},\
  59         /* polling until return 0*/ \
  60         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  61                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},\
  62         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  63                 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0},
  64 
  65 /* format */
  66 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
  67 
  68 #define RTL8723A_TRANS_ACT_TO_CARDEMU   \
  69         /*0x1F[7:0] = 0 turn off RF*/ \
  70         {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  71                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},      \
  72         {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  73                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},\
  74         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  75                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \
  76         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
  77                 PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0},
  78 
  79 /* format */
  80 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/
  81 #define RTL8723A_TRANS_CARDEMU_TO_SUS                   \
  82                 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/      \
  83         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,\
  84                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, \
  85                 BIT(4)|BIT(3), (BIT(4)|BIT(3))},\
  86 /*0x04[12:11] = 2b'01 enable WL suspend*/       \
  87         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK| \
  88                 PWR_INTF_SDIO_MSK,\
  89                 PWR_BASEADDR_MAC, \
  90                 PWR_CMD_WRITE, \
  91                 BIT(3)|BIT(4), BIT(3)}, \
  92 /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
  93         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
  94                 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, \
  95                 PWR_CMD_WRITE, BIT(3)|BIT(4), \
  96                 BIT(3)|BIT(4)}, \
  97 /*Set SDIO suspend local register*/     \
  98         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
  99                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 100                 PWR_CMD_WRITE, BIT(0), BIT(0)}, \
 101 /*wait power state to suspend*/ \
 102         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 103                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 104                 PWR_CMD_POLLING, BIT(1), 0},
 105 
 106 /* format */
 107 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 108 
 109 #define RTL8723A_TRANS_SUS_TO_CARDEMU   \
 110  /*Set SDIO suspend local register*/    \
 111         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\
 112                 PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0},\
 113  /*wait power state to suspend*/ \
 114         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,\
 115                 PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)},\
 116  /*0x04[12:11] = 2b'00 disable WL suspend*/ \
 117         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
 118                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0},
 119 
 120 /* format */
 121 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 122 
 123 #define RTL8723A_TRANS_CARDEMU_TO_CARDDIS \
 124  /*0x04[12:11] = 2b'01 enable WL suspend*/       \
 125         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 126                 PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \
 127                 PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \
 128 /*0x04[10] = 1, enable SW LPS*/ \
 129         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 130                 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\
 131                 PWR_CMD_WRITE, BIT(2), BIT(2)}, \
 132 /*Set SDIO suspend local register*/ \
 133         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 134                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 135                 PWR_CMD_WRITE, BIT(0), BIT(0)}, \
 136  /*wait power state to suspend*/ \
 137         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 138                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 139                 PWR_CMD_POLLING, BIT(1), 0},
 140 
 141 /* format */
 142 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 143 
 144 #define RTL8723A_TRANS_CARDDIS_TO_CARDEMU\
 145 /*Set SDIO suspend local register*/     \
 146         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 147                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 148                 PWR_CMD_WRITE, BIT(0), 0}, \
 149  /*wait power state to suspend*/ \
 150         {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 151                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 152                 PWR_CMD_POLLING, BIT(1), BIT(1)},\
 153  /*0x04[12:11] = 2b'00 disable WL suspend*/ \
 154         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 155                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 156                 PWR_CMD_WRITE, BIT(3)|BIT(4), 0},\
 157 /*PCIe DMA start*/ \
 158         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 159                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 160                 PWR_CMD_WRITE, 0xFF, 0},
 161 
 162 /* format */
 163 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 164 #define RTL8723A_TRANS_CARDEMU_TO_PDN   \
 165         {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 166                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 167                 PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
 168         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 169                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 170                 PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
 171 
 172 /* format */
 173 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 174 #define RTL8723A_TRANS_PDN_TO_CARDEMU   \
 175         {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 176                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 177                 PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/
 178 
 179 /* format */
 180 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 181 
 182 #define RTL8723A_TRANS_ACT_TO_LPS       \
 183         {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 184                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 185                 PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/    \
 186         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 187                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 188                 PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \
 189         /*Should be zero if no packet is transmitting*/ \
 190         {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 191                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 192                 PWR_CMD_POLLING, 0xFF, 0},\
 193         /*Should be zero if no packet is transmitting*/ \
 194         {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 195                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 196                 PWR_CMD_POLLING, 0xFF, 0},\
 197         /*Should be zero if no packet is transmitting*/ \
 198         {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 199                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 200                 PWR_CMD_POLLING, 0xFF, 0},\
 201         /*Should be zero if no packet is transmitting*/ \
 202         {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 203                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 204                 PWR_CMD_POLLING, 0xFF, 0},\
 205         /*CCK and OFDM are disabled,and clock are gated*/ \
 206         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 207                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 208                 PWR_CMD_WRITE, BIT(0), 0},\
 209         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 210                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 211                 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/\
 212         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 213                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 214                 PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \
 215         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 216                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 217                 PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/    \
 218         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 219                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 220                 PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/    \
 221         /*Respond TxOK to scheduler*/   \
 222         {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 223                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 224                 PWR_CMD_WRITE, BIT(5), BIT(5)},\
 225 
 226 #define RTL8723A_TRANS_LPS_TO_ACT\
 227 /* format */    \
 228 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */ \
 229         {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 230                 PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO,\
 231                 PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
 232         {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 233                 PWR_INTF_USB_MSK, PWR_BASEADDR_MAC,\
 234                 PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
 235         {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 236                 PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC,\
 237                 PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
 238         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 239                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 240                 PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
 241         /*.     0x08[4] = 0              switch TSF to 40M*/\
 242         {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 243                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 244                 PWR_CMD_WRITE, BIT(4), 0},  \
 245         /*Polling 0x109[7]=0  TSF in 40M*/\
 246         {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 247                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 248                 PWR_CMD_POLLING, BIT(7), 0}, \
 249         /*.     0x29[7:6] = 2b'00        enable BB clock*/\
 250         {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 251                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 252                 PWR_CMD_WRITE, BIT(6)|BIT(7), 0},\
 253          /*.    0x101[1] = 1*/\
 254         {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 255                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 256                 PWR_CMD_WRITE, BIT(1), BIT(1)},\
 257          /*.    0x100[7:0] = 0xFF        enable WMAC TRX*/\
 258         {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 259                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 260                 PWR_CMD_WRITE, 0xFF, 0xFF},\
 261          /*.    0x02[1:0] = 2b'11        enable BB macro*/\
 262         {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 263                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 264                 PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)},\
 265         {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \
 266                 PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC,\
 267                 PWR_CMD_WRITE, 0xFF, 0}, /*.    0x522 = 0*/
 268 
 269 /* format */
 270 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */
 271 
 272 #define RTL8723A_TRANS_END \
 273         {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\
 274         0, PWR_CMD_END, 0, 0}
 275 
 276 extern struct wlan_pwr_cfg rtl8723A_power_on_flow
 277                 [RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS +
 278                  RTL8723A_TRANS_END_STEPS];
 279 extern struct wlan_pwr_cfg rtl8723A_radio_off_flow
 280                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 281                  RTL8723A_TRANS_END_STEPS];
 282 extern struct wlan_pwr_cfg rtl8723A_card_disable_flow
 283                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 284                  RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
 285                  RTL8723A_TRANS_END_STEPS];
 286 extern struct wlan_pwr_cfg rtl8723A_card_enable_flow
 287                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 288                  RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
 289                  RTL8723A_TRANS_END_STEPS];
 290 extern struct wlan_pwr_cfg rtl8723A_suspend_flow
 291                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 292                  RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS +
 293                  RTL8723A_TRANS_END_STEPS];
 294 extern struct wlan_pwr_cfg rtl8723A_resume_flow
 295                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 296                  RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS +
 297                  RTL8723A_TRANS_END_STEPS];
 298 extern struct wlan_pwr_cfg rtl8723A_hwpdn_flow
 299                 [RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS +
 300                  RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS +
 301                  RTL8723A_TRANS_END_STEPS];
 302 extern struct wlan_pwr_cfg rtl8723A_enter_lps_flow
 303                 [RTL8723A_TRANS_ACT_TO_LPS_STEPS + RTL8723A_TRANS_END_STEPS];
 304 extern struct wlan_pwr_cfg rtl8723A_leave_lps_flow
 305                 [RTL8723A_TRANS_LPS_TO_ACT_STEPS + RTL8723A_TRANS_END_STEPS];
 306 
 307 /* RTL8723 Power Configuration CMDs for PCIe interface */
 308 #define RTL8723_NIC_PWR_ON_FLOW         rtl8723A_power_on_flow
 309 #define RTL8723_NIC_RF_OFF_FLOW         rtl8723A_radio_off_flow
 310 #define RTL8723_NIC_DISABLE_FLOW        rtl8723A_card_disable_flow
 311 #define RTL8723_NIC_ENABLE_FLOW         rtl8723A_card_enable_flow
 312 #define RTL8723_NIC_SUSPEND_FLOW        rtl8723A_suspend_flow
 313 #define RTL8723_NIC_RESUME_FLOW         rtl8723A_resume_flow
 314 #define RTL8723_NIC_PDN_FLOW            rtl8723A_hwpdn_flow
 315 #define RTL8723_NIC_LPS_ENTER_FLOW      rtl8723A_enter_lps_flow
 316 #define RTL8723_NIC_LPS_LEAVE_FLOW      rtl8723A_leave_lps_flow
 317 
 318 #endif
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/net/wireless/realtek/rtlwifi/rtl8723ae/pwrseq.h

INCLUDED FROM
