This source file includes following definitions.
- qcom_scm_remap_error
1
2
3
4 #ifndef __QCOM_SCM_INT_H
5 #define __QCOM_SCM_INT_H
6
7 #define QCOM_SCM_SVC_BOOT 0x1
8 #define QCOM_SCM_BOOT_ADDR 0x1
9 #define QCOM_SCM_SET_DLOAD_MODE 0x10
10 #define QCOM_SCM_BOOT_ADDR_MC 0x11
11 #define QCOM_SCM_SET_REMOTE_STATE 0xa
12 extern int __qcom_scm_set_remote_state(struct device *dev, u32 state, u32 id);
13 extern int __qcom_scm_set_dload_mode(struct device *dev, bool enable);
14
15 #define QCOM_SCM_FLAG_HLOS 0x01
16 #define QCOM_SCM_FLAG_COLDBOOT_MC 0x02
17 #define QCOM_SCM_FLAG_WARMBOOT_MC 0x04
18 extern int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
19 const cpumask_t *cpus);
20 extern int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus);
21
22 #define QCOM_SCM_CMD_TERMINATE_PC 0x2
23 #define QCOM_SCM_FLUSH_FLAG_MASK 0x3
24 #define QCOM_SCM_CMD_CORE_HOTPLUGGED 0x10
25 extern void __qcom_scm_cpu_power_down(u32 flags);
26
27 #define QCOM_SCM_SVC_IO 0x5
28 #define QCOM_SCM_IO_READ 0x1
29 #define QCOM_SCM_IO_WRITE 0x2
30 extern int __qcom_scm_io_readl(struct device *dev, phys_addr_t addr, unsigned int *val);
31 extern int __qcom_scm_io_writel(struct device *dev, phys_addr_t addr, unsigned int val);
32
33 #define QCOM_SCM_SVC_INFO 0x6
34 #define QCOM_IS_CALL_AVAIL_CMD 0x1
35 extern int __qcom_scm_is_call_available(struct device *dev, u32 svc_id,
36 u32 cmd_id);
37
38 #define QCOM_SCM_SVC_HDCP 0x11
39 #define QCOM_SCM_CMD_HDCP 0x01
40 extern int __qcom_scm_hdcp_req(struct device *dev,
41 struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp);
42
43 extern void __qcom_scm_init(void);
44
45 #define QCOM_SCM_SVC_PIL 0x2
46 #define QCOM_SCM_PAS_INIT_IMAGE_CMD 0x1
47 #define QCOM_SCM_PAS_MEM_SETUP_CMD 0x2
48 #define QCOM_SCM_PAS_AUTH_AND_RESET_CMD 0x5
49 #define QCOM_SCM_PAS_SHUTDOWN_CMD 0x6
50 #define QCOM_SCM_PAS_IS_SUPPORTED_CMD 0x7
51 #define QCOM_SCM_PAS_MSS_RESET 0xa
52 extern bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral);
53 extern int __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
54 dma_addr_t metadata_phys);
55 extern int __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
56 phys_addr_t addr, phys_addr_t size);
57 extern int __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral);
58 extern int __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral);
59 extern int __qcom_scm_pas_mss_reset(struct device *dev, bool reset);
60
61
62 #define QCOM_SCM_V2_EBUSY -12
63 #define QCOM_SCM_ENOMEM -5
64 #define QCOM_SCM_EOPNOTSUPP -4
65 #define QCOM_SCM_EINVAL_ADDR -3
66 #define QCOM_SCM_EINVAL_ARG -2
67 #define QCOM_SCM_ERROR -1
68 #define QCOM_SCM_INTERRUPTED 1
69
70 static inline int qcom_scm_remap_error(int err)
71 {
72 switch (err) {
73 case QCOM_SCM_ERROR:
74 return -EIO;
75 case QCOM_SCM_EINVAL_ADDR:
76 case QCOM_SCM_EINVAL_ARG:
77 return -EINVAL;
78 case QCOM_SCM_EOPNOTSUPP:
79 return -EOPNOTSUPP;
80 case QCOM_SCM_ENOMEM:
81 return -ENOMEM;
82 case QCOM_SCM_V2_EBUSY:
83 return -EBUSY;
84 }
85 return -EINVAL;
86 }
87
88 #define QCOM_SCM_SVC_MP 0xc
89 #define QCOM_SCM_RESTORE_SEC_CFG 2
90 extern int __qcom_scm_restore_sec_cfg(struct device *dev, u32 device_id,
91 u32 spare);
92 #define QCOM_SCM_IOMMU_SECURE_PTBL_SIZE 3
93 #define QCOM_SCM_IOMMU_SECURE_PTBL_INIT 4
94 extern int __qcom_scm_iommu_secure_ptbl_size(struct device *dev, u32 spare,
95 size_t *size);
96 extern int __qcom_scm_iommu_secure_ptbl_init(struct device *dev, u64 addr,
97 u32 size, u32 spare);
98 #define QCOM_MEM_PROT_ASSIGN_ID 0x16
99 extern int __qcom_scm_assign_mem(struct device *dev,
100 phys_addr_t mem_region, size_t mem_sz,
101 phys_addr_t src, size_t src_sz,
102 phys_addr_t dest, size_t dest_sz);
103
104 #endif