root/drivers/scsi/mesh.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. readtb
  2. dlog
  3. dumplog
  4. dumpslog
  5. dlog
  6. dumplog
  7. dumpslog
  8. mesh_dump_regs
  9. mesh_flush_io
  10. mesh_completed
  11. mesh_init
  12. mesh_start_cmd
  13. mesh_start
  14. mesh_done
  15. add_sdtr_msg
  16. set_sdtr
  17. start_phase
  18. get_msgin
  19. msgin_length
  20. reselected
  21. do_abort
  22. handle_reset
  23. do_mesh_interrupt
  24. handle_error
  25. handle_exception
  26. handle_msgin
  27. set_dma_cmds
  28. halt_dma
  29. phase_mismatch
  30. cmd_complete
  31. mesh_queue_lck
  32. DEF_SCSI_QCMD
  33. mesh_abort
  34. mesh_host_reset
  35. set_mesh_power
  36. mesh_suspend
  37. mesh_resume
  38. mesh_shutdown
  39. mesh_probe
  40. mesh_remove
  41. init_mesh
  42. exit_mesh

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * SCSI low-level driver for the MESH (Macintosh Enhanced SCSI Hardware)
   4  * bus adaptor found on Power Macintosh computers.
   5  * We assume the MESH is connected to a DBDMA (descriptor-based DMA)
   6  * controller.
   7  *
   8  * Paul Mackerras, August 1996.
   9  * Copyright (C) 1996 Paul Mackerras.
  10  *
  11  * Apr. 21 2002  - BenH         Rework bus reset code for new error handler
  12  *                              Add delay after initial bus reset
  13  *                              Add module parameters
  14  *
  15  * Sep. 27 2003  - BenH         Move to new driver model, fix some write posting
  16  *                              issues
  17  * To do:
  18  * - handle aborts correctly
  19  * - retry arbitration if lost (unless higher levels do this for us)
  20  * - power down the chip when no device is detected
  21  */
  22 #include <linux/module.h>
  23 #include <linux/kernel.h>
  24 #include <linux/delay.h>
  25 #include <linux/types.h>
  26 #include <linux/string.h>
  27 #include <linux/blkdev.h>
  28 #include <linux/proc_fs.h>
  29 #include <linux/stat.h>
  30 #include <linux/interrupt.h>
  31 #include <linux/reboot.h>
  32 #include <linux/spinlock.h>
  33 #include <linux/pci.h>
  34 #include <asm/dbdma.h>
  35 #include <asm/io.h>
  36 #include <asm/pgtable.h>
  37 #include <asm/prom.h>
  38 #include <asm/irq.h>
  39 #include <asm/hydra.h>
  40 #include <asm/processor.h>
  41 #include <asm/machdep.h>
  42 #include <asm/pmac_feature.h>
  43 #include <asm/macio.h>
  44 
  45 #include <scsi/scsi.h>
  46 #include <scsi/scsi_cmnd.h>
  47 #include <scsi/scsi_device.h>
  48 #include <scsi/scsi_host.h>
  49 
  50 #include "mesh.h"
  51 
  52 #if 1
  53 #undef KERN_DEBUG
  54 #define KERN_DEBUG KERN_WARNING
  55 #endif
  56 
  57 MODULE_AUTHOR("Paul Mackerras (paulus@samba.org)");
  58 MODULE_DESCRIPTION("PowerMac MESH SCSI driver");
  59 MODULE_LICENSE("GPL");
  60 
  61 static int sync_rate = CONFIG_SCSI_MESH_SYNC_RATE;
  62 static int sync_targets = 0xff;
  63 static int resel_targets = 0xff;
  64 static int debug_targets = 0;   /* print debug for these targets */
  65 static int init_reset_delay = CONFIG_SCSI_MESH_RESET_DELAY_MS;
  66 
  67 module_param(sync_rate, int, 0);
  68 MODULE_PARM_DESC(sync_rate, "Synchronous rate (0..10, 0=async)");
  69 module_param(sync_targets, int, 0);
  70 MODULE_PARM_DESC(sync_targets, "Bitmask of targets allowed to set synchronous");
  71 module_param(resel_targets, int, 0);
  72 MODULE_PARM_DESC(resel_targets, "Bitmask of targets allowed to set disconnect");
  73 module_param(debug_targets, int, 0644);
  74 MODULE_PARM_DESC(debug_targets, "Bitmask of debugged targets");
  75 module_param(init_reset_delay, int, 0);
  76 MODULE_PARM_DESC(init_reset_delay, "Initial bus reset delay (0=no reset)");
  77 
  78 static int mesh_sync_period = 100;
  79 static int mesh_sync_offset = 0;
  80 static unsigned char use_active_neg = 0;  /* bit mask for SEQ_ACTIVE_NEG if used */
  81 
  82 #define ALLOW_SYNC(tgt)         ((sync_targets >> (tgt)) & 1)
  83 #define ALLOW_RESEL(tgt)        ((resel_targets >> (tgt)) & 1)
  84 #define ALLOW_DEBUG(tgt)        ((debug_targets >> (tgt)) & 1)
  85 #define DEBUG_TARGET(cmd)       ((cmd) && ALLOW_DEBUG((cmd)->device->id))
  86 
  87 #undef MESH_DBG
  88 #define N_DBG_LOG       50
  89 #define N_DBG_SLOG      20
  90 #define NUM_DBG_EVENTS  13
  91 #undef  DBG_USE_TB              /* bombs on 601 */
  92 
  93 struct dbglog {
  94         char    *fmt;
  95         u32     tb;
  96         u8      phase;
  97         u8      bs0;
  98         u8      bs1;
  99         u8      tgt;
 100         int     d;
 101 };
 102 
 103 enum mesh_phase {
 104         idle,
 105         arbitrating,
 106         selecting,
 107         commanding,
 108         dataing,
 109         statusing,
 110         busfreeing,
 111         disconnecting,
 112         reselecting,
 113         sleeping
 114 };
 115 
 116 enum msg_phase {
 117         msg_none,
 118         msg_out,
 119         msg_out_xxx,
 120         msg_out_last,
 121         msg_in,
 122         msg_in_bad,
 123 };
 124 
 125 enum sdtr_phase {
 126         do_sdtr,
 127         sdtr_sent,
 128         sdtr_done
 129 };
 130 
 131 struct mesh_target {
 132         enum sdtr_phase sdtr_state;
 133         int     sync_params;
 134         int     data_goes_out;          /* guess as to data direction */
 135         struct scsi_cmnd *current_req;
 136         u32     saved_ptr;
 137 #ifdef MESH_DBG
 138         int     log_ix;
 139         int     n_log;
 140         struct dbglog log[N_DBG_LOG];
 141 #endif
 142 };
 143 
 144 struct mesh_state {
 145         volatile struct mesh_regs __iomem *mesh;
 146         int     meshintr;
 147         volatile struct dbdma_regs __iomem *dma;
 148         int     dmaintr;
 149         struct  Scsi_Host *host;
 150         struct  mesh_state *next;
 151         struct scsi_cmnd *request_q;
 152         struct scsi_cmnd *request_qtail;
 153         enum mesh_phase phase;          /* what we're currently trying to do */
 154         enum msg_phase msgphase;
 155         int     conn_tgt;               /* target we're connected to */
 156         struct scsi_cmnd *current_req;          /* req we're currently working on */
 157         int     data_ptr;
 158         int     dma_started;
 159         int     dma_count;
 160         int     stat;
 161         int     aborting;
 162         int     expect_reply;
 163         int     n_msgin;
 164         u8      msgin[16];
 165         int     n_msgout;
 166         int     last_n_msgout;
 167         u8      msgout[16];
 168         struct dbdma_cmd *dma_cmds;     /* space for dbdma commands, aligned */
 169         dma_addr_t dma_cmd_bus;
 170         void    *dma_cmd_space;
 171         int     dma_cmd_size;
 172         int     clk_freq;
 173         struct mesh_target tgts[8];
 174         struct macio_dev *mdev;
 175         struct pci_dev* pdev;
 176 #ifdef MESH_DBG
 177         int     log_ix;
 178         int     n_log;
 179         struct dbglog log[N_DBG_SLOG];
 180 #endif
 181 };
 182 
 183 /*
 184  * Driver is too messy, we need a few prototypes...
 185  */
 186 static void mesh_done(struct mesh_state *ms, int start_next);
 187 static void mesh_interrupt(struct mesh_state *ms);
 188 static void cmd_complete(struct mesh_state *ms);
 189 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd);
 190 static void halt_dma(struct mesh_state *ms);
 191 static void phase_mismatch(struct mesh_state *ms);
 192 
 193 
 194 /*
 195  * Some debugging & logging routines
 196  */
 197 
 198 #ifdef MESH_DBG
 199 
 200 static inline u32 readtb(void)
 201 {
 202         u32 tb;
 203 
 204 #ifdef DBG_USE_TB
 205         /* Beware: if you enable this, it will crash on 601s. */
 206         asm ("mftb %0" : "=r" (tb) : );
 207 #else
 208         tb = 0;
 209 #endif
 210         return tb;
 211 }
 212 
 213 static void dlog(struct mesh_state *ms, char *fmt, int a)
 214 {
 215         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 216         struct dbglog *tlp, *slp;
 217 
 218         tlp = &tp->log[tp->log_ix];
 219         slp = &ms->log[ms->log_ix];
 220         tlp->fmt = fmt;
 221         tlp->tb = readtb();
 222         tlp->phase = (ms->msgphase << 4) + ms->phase;
 223         tlp->bs0 = ms->mesh->bus_status0;
 224         tlp->bs1 = ms->mesh->bus_status1;
 225         tlp->tgt = ms->conn_tgt;
 226         tlp->d = a;
 227         *slp = *tlp;
 228         if (++tp->log_ix >= N_DBG_LOG)
 229                 tp->log_ix = 0;
 230         if (tp->n_log < N_DBG_LOG)
 231                 ++tp->n_log;
 232         if (++ms->log_ix >= N_DBG_SLOG)
 233                 ms->log_ix = 0;
 234         if (ms->n_log < N_DBG_SLOG)
 235                 ++ms->n_log;
 236 }
 237 
 238 static void dumplog(struct mesh_state *ms, int t)
 239 {
 240         struct mesh_target *tp = &ms->tgts[t];
 241         struct dbglog *lp;
 242         int i;
 243 
 244         if (tp->n_log == 0)
 245                 return;
 246         i = tp->log_ix - tp->n_log;
 247         if (i < 0)
 248                 i += N_DBG_LOG;
 249         tp->n_log = 0;
 250         do {
 251                 lp = &tp->log[i];
 252                 printk(KERN_DEBUG "mesh log %d: bs=%.2x%.2x ph=%.2x ",
 253                        t, lp->bs1, lp->bs0, lp->phase);
 254 #ifdef DBG_USE_TB
 255                 printk("tb=%10u ", lp->tb);
 256 #endif
 257                 printk(lp->fmt, lp->d);
 258                 printk("\n");
 259                 if (++i >= N_DBG_LOG)
 260                         i = 0;
 261         } while (i != tp->log_ix);
 262 }
 263 
 264 static void dumpslog(struct mesh_state *ms)
 265 {
 266         struct dbglog *lp;
 267         int i;
 268 
 269         if (ms->n_log == 0)
 270                 return;
 271         i = ms->log_ix - ms->n_log;
 272         if (i < 0)
 273                 i += N_DBG_SLOG;
 274         ms->n_log = 0;
 275         do {
 276                 lp = &ms->log[i];
 277                 printk(KERN_DEBUG "mesh log: bs=%.2x%.2x ph=%.2x t%d ",
 278                        lp->bs1, lp->bs0, lp->phase, lp->tgt);
 279 #ifdef DBG_USE_TB
 280                 printk("tb=%10u ", lp->tb);
 281 #endif
 282                 printk(lp->fmt, lp->d);
 283                 printk("\n");
 284                 if (++i >= N_DBG_SLOG)
 285                         i = 0;
 286         } while (i != ms->log_ix);
 287 }
 288 
 289 #else
 290 
 291 static inline void dlog(struct mesh_state *ms, char *fmt, int a)
 292 {}
 293 static inline void dumplog(struct mesh_state *ms, int tgt)
 294 {}
 295 static inline void dumpslog(struct mesh_state *ms)
 296 {}
 297 
 298 #endif /* MESH_DBG */
 299 
 300 #define MKWORD(a, b, c, d)      (((a) << 24) + ((b) << 16) + ((c) << 8) + (d))
 301 
 302 static void
 303 mesh_dump_regs(struct mesh_state *ms)
 304 {
 305         volatile struct mesh_regs __iomem *mr = ms->mesh;
 306         volatile struct dbdma_regs __iomem *md = ms->dma;
 307         int t;
 308         struct mesh_target *tp;
 309 
 310         printk(KERN_DEBUG "mesh: state at %p, regs at %p, dma at %p\n",
 311                ms, mr, md);
 312         printk(KERN_DEBUG "    ct=%4x seq=%2x bs=%4x fc=%2x "
 313                "exc=%2x err=%2x im=%2x int=%2x sp=%2x\n",
 314                (mr->count_hi << 8) + mr->count_lo, mr->sequence,
 315                (mr->bus_status1 << 8) + mr->bus_status0, mr->fifo_count,
 316                mr->exception, mr->error, mr->intr_mask, mr->interrupt,
 317                mr->sync_params);
 318         while(in_8(&mr->fifo_count))
 319                 printk(KERN_DEBUG " fifo data=%.2x\n",in_8(&mr->fifo));
 320         printk(KERN_DEBUG "    dma stat=%x cmdptr=%x\n",
 321                in_le32(&md->status), in_le32(&md->cmdptr));
 322         printk(KERN_DEBUG "    phase=%d msgphase=%d conn_tgt=%d data_ptr=%d\n",
 323                ms->phase, ms->msgphase, ms->conn_tgt, ms->data_ptr);
 324         printk(KERN_DEBUG "    dma_st=%d dma_ct=%d n_msgout=%d\n",
 325                ms->dma_started, ms->dma_count, ms->n_msgout);
 326         for (t = 0; t < 8; ++t) {
 327                 tp = &ms->tgts[t];
 328                 if (tp->current_req == NULL)
 329                         continue;
 330                 printk(KERN_DEBUG "    target %d: req=%p goes_out=%d saved_ptr=%d\n",
 331                        t, tp->current_req, tp->data_goes_out, tp->saved_ptr);
 332         }
 333 }
 334 
 335 
 336 /*
 337  * Flush write buffers on the bus path to the mesh
 338  */
 339 static inline void mesh_flush_io(volatile struct mesh_regs __iomem *mr)
 340 {
 341         (void)in_8(&mr->mesh_id);
 342 }
 343 
 344 
 345 /*
 346  * Complete a SCSI command
 347  */
 348 static void mesh_completed(struct mesh_state *ms, struct scsi_cmnd *cmd)
 349 {
 350         (*cmd->scsi_done)(cmd);
 351 }
 352 
 353 
 354 /* Called with  meshinterrupt disabled, initialize the chipset
 355  * and eventually do the initial bus reset. The lock must not be
 356  * held since we can schedule.
 357  */
 358 static void mesh_init(struct mesh_state *ms)
 359 {
 360         volatile struct mesh_regs __iomem *mr = ms->mesh;
 361         volatile struct dbdma_regs __iomem *md = ms->dma;
 362 
 363         mesh_flush_io(mr);
 364         udelay(100);
 365 
 366         /* Reset controller */
 367         out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16);   /* stop dma */
 368         out_8(&mr->exception, 0xff);    /* clear all exception bits */
 369         out_8(&mr->error, 0xff);        /* clear all error bits */
 370         out_8(&mr->sequence, SEQ_RESETMESH);
 371         mesh_flush_io(mr);
 372         udelay(10);
 373         out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 374         out_8(&mr->source_id, ms->host->this_id);
 375         out_8(&mr->sel_timeout, 25);    /* 250ms */
 376         out_8(&mr->sync_params, ASYNC_PARAMS);
 377 
 378         if (init_reset_delay) {
 379                 printk(KERN_INFO "mesh: performing initial bus reset...\n");
 380                 
 381                 /* Reset bus */
 382                 out_8(&mr->bus_status1, BS1_RST);       /* assert RST */
 383                 mesh_flush_io(mr);
 384                 udelay(30);                     /* leave it on for >= 25us */
 385                 out_8(&mr->bus_status1, 0);     /* negate RST */
 386                 mesh_flush_io(mr);
 387 
 388                 /* Wait for bus to come back */
 389                 msleep(init_reset_delay);
 390         }
 391         
 392         /* Reconfigure controller */
 393         out_8(&mr->interrupt, 0xff);    /* clear all interrupt bits */
 394         out_8(&mr->sequence, SEQ_FLUSHFIFO);
 395         mesh_flush_io(mr);
 396         udelay(1);
 397         out_8(&mr->sync_params, ASYNC_PARAMS);
 398         out_8(&mr->sequence, SEQ_ENBRESEL);
 399 
 400         ms->phase = idle;
 401         ms->msgphase = msg_none;
 402 }
 403 
 404 
 405 static void mesh_start_cmd(struct mesh_state *ms, struct scsi_cmnd *cmd)
 406 {
 407         volatile struct mesh_regs __iomem *mr = ms->mesh;
 408         int t, id;
 409 
 410         id = cmd->device->id;
 411         ms->current_req = cmd;
 412         ms->tgts[id].data_goes_out = cmd->sc_data_direction == DMA_TO_DEVICE;
 413         ms->tgts[id].current_req = cmd;
 414 
 415 #if 1
 416         if (DEBUG_TARGET(cmd)) {
 417                 int i;
 418                 printk(KERN_DEBUG "mesh_start: %p tgt=%d cmd=", cmd, id);
 419                 for (i = 0; i < cmd->cmd_len; ++i)
 420                         printk(" %x", cmd->cmnd[i]);
 421                 printk(" use_sg=%d buffer=%p bufflen=%u\n",
 422                        scsi_sg_count(cmd), scsi_sglist(cmd), scsi_bufflen(cmd));
 423         }
 424 #endif
 425         if (ms->dma_started)
 426                 panic("mesh: double DMA start !\n");
 427 
 428         ms->phase = arbitrating;
 429         ms->msgphase = msg_none;
 430         ms->data_ptr = 0;
 431         ms->dma_started = 0;
 432         ms->n_msgout = 0;
 433         ms->last_n_msgout = 0;
 434         ms->expect_reply = 0;
 435         ms->conn_tgt = id;
 436         ms->tgts[id].saved_ptr = 0;
 437         ms->stat = DID_OK;
 438         ms->aborting = 0;
 439 #ifdef MESH_DBG
 440         ms->tgts[id].n_log = 0;
 441         dlog(ms, "start cmd=%x", (int) cmd);
 442 #endif
 443 
 444         /* Off we go */
 445         dlog(ms, "about to arb, intr/exc/err/fc=%.8x",
 446              MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 447         out_8(&mr->interrupt, INT_CMDDONE);
 448         out_8(&mr->sequence, SEQ_ENBRESEL);
 449         mesh_flush_io(mr);
 450         udelay(1);
 451 
 452         if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
 453                 /*
 454                  * Some other device has the bus or is arbitrating for it -
 455                  * probably a target which is about to reselect us.
 456                  */
 457                 dlog(ms, "busy b4 arb, intr/exc/err/fc=%.8x",
 458                      MKWORD(mr->interrupt, mr->exception,
 459                             mr->error, mr->fifo_count));
 460                 for (t = 100; t > 0; --t) {
 461                         if ((in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) == 0)
 462                                 break;
 463                         if (in_8(&mr->interrupt) != 0) {
 464                                 dlog(ms, "intr b4 arb, intr/exc/err/fc=%.8x",
 465                                      MKWORD(mr->interrupt, mr->exception,
 466                                             mr->error, mr->fifo_count));
 467                                 mesh_interrupt(ms);
 468                                 if (ms->phase != arbitrating)
 469                                         return;
 470                         }
 471                         udelay(1);
 472                 }
 473                 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
 474                         /* XXX should try again in a little while */
 475                         ms->stat = DID_BUS_BUSY;
 476                         ms->phase = idle;
 477                         mesh_done(ms, 0);
 478                         return;
 479                 }
 480         }
 481 
 482         /*
 483          * Apparently the mesh has a bug where it will assert both its
 484          * own bit and the target's bit on the bus during arbitration.
 485          */
 486         out_8(&mr->dest_id, mr->source_id);
 487 
 488         /*
 489          * There appears to be a race with reselection sometimes,
 490          * where a target reselects us just as we issue the
 491          * arbitrate command.  It seems that then the arbitrate
 492          * command just hangs waiting for the bus to be free
 493          * without giving us a reselection exception.
 494          * The only way I have found to get it to respond correctly
 495          * is this: disable reselection before issuing the arbitrate
 496          * command, then after issuing it, if it looks like a target
 497          * is trying to reselect us, reset the mesh and then enable
 498          * reselection.
 499          */
 500         out_8(&mr->sequence, SEQ_DISRESEL);
 501         if (in_8(&mr->interrupt) != 0) {
 502                 dlog(ms, "intr after disresel, intr/exc/err/fc=%.8x",
 503                      MKWORD(mr->interrupt, mr->exception,
 504                             mr->error, mr->fifo_count));
 505                 mesh_interrupt(ms);
 506                 if (ms->phase != arbitrating)
 507                         return;
 508                 dlog(ms, "after intr after disresel, intr/exc/err/fc=%.8x",
 509                      MKWORD(mr->interrupt, mr->exception,
 510                             mr->error, mr->fifo_count));
 511         }
 512 
 513         out_8(&mr->sequence, SEQ_ARBITRATE);
 514 
 515         for (t = 230; t > 0; --t) {
 516                 if (in_8(&mr->interrupt) != 0)
 517                         break;
 518                 udelay(1);
 519         }
 520         dlog(ms, "after arb, intr/exc/err/fc=%.8x",
 521              MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 522         if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
 523             && (in_8(&mr->bus_status0) & BS0_IO)) {
 524                 /* looks like a reselection - try resetting the mesh */
 525                 dlog(ms, "resel? after arb, intr/exc/err/fc=%.8x",
 526                      MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 527                 out_8(&mr->sequence, SEQ_RESETMESH);
 528                 mesh_flush_io(mr);
 529                 udelay(10);
 530                 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 531                 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 532                 out_8(&mr->sequence, SEQ_ENBRESEL);
 533                 mesh_flush_io(mr);
 534                 for (t = 10; t > 0 && in_8(&mr->interrupt) == 0; --t)
 535                         udelay(1);
 536                 dlog(ms, "tried reset after arb, intr/exc/err/fc=%.8x",
 537                      MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
 538 #ifndef MESH_MULTIPLE_HOSTS
 539                 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
 540                     && (in_8(&mr->bus_status0) & BS0_IO)) {
 541                         printk(KERN_ERR "mesh: controller not responding"
 542                                " to reselection!\n");
 543                         /*
 544                          * If this is a target reselecting us, and the
 545                          * mesh isn't responding, the higher levels of
 546                          * the scsi code will eventually time out and
 547                          * reset the bus.
 548                          */
 549                 }
 550 #endif
 551         }
 552 }
 553 
 554 /*
 555  * Start the next command for a MESH.
 556  * Should be called with interrupts disabled.
 557  */
 558 static void mesh_start(struct mesh_state *ms)
 559 {
 560         struct scsi_cmnd *cmd, *prev, *next;
 561 
 562         if (ms->phase != idle || ms->current_req != NULL) {
 563                 printk(KERN_ERR "inappropriate mesh_start (phase=%d, ms=%p)",
 564                        ms->phase, ms);
 565                 return;
 566         }
 567 
 568         while (ms->phase == idle) {
 569                 prev = NULL;
 570                 for (cmd = ms->request_q; ; cmd = (struct scsi_cmnd *) cmd->host_scribble) {
 571                         if (cmd == NULL)
 572                                 return;
 573                         if (ms->tgts[cmd->device->id].current_req == NULL)
 574                                 break;
 575                         prev = cmd;
 576                 }
 577                 next = (struct scsi_cmnd *) cmd->host_scribble;
 578                 if (prev == NULL)
 579                         ms->request_q = next;
 580                 else
 581                         prev->host_scribble = (void *) next;
 582                 if (next == NULL)
 583                         ms->request_qtail = prev;
 584 
 585                 mesh_start_cmd(ms, cmd);
 586         }
 587 }
 588 
 589 static void mesh_done(struct mesh_state *ms, int start_next)
 590 {
 591         struct scsi_cmnd *cmd;
 592         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 593 
 594         cmd = ms->current_req;
 595         ms->current_req = NULL;
 596         tp->current_req = NULL;
 597         if (cmd) {
 598                 cmd->result = (ms->stat << 16) | cmd->SCp.Status;
 599                 if (ms->stat == DID_OK)
 600                         cmd->result |= cmd->SCp.Message << 8;
 601                 if (DEBUG_TARGET(cmd)) {
 602                         printk(KERN_DEBUG "mesh_done: result = %x, data_ptr=%d, buflen=%d\n",
 603                                cmd->result, ms->data_ptr, scsi_bufflen(cmd));
 604 #if 0
 605                         /* needs to use sg? */
 606                         if ((cmd->cmnd[0] == 0 || cmd->cmnd[0] == 0x12 || cmd->cmnd[0] == 3)
 607                             && cmd->request_buffer != 0) {
 608                                 unsigned char *b = cmd->request_buffer;
 609                                 printk(KERN_DEBUG "buffer = %x %x %x %x %x %x %x %x\n",
 610                                        b[0], b[1], b[2], b[3], b[4], b[5], b[6], b[7]);
 611                         }
 612 #endif
 613                 }
 614                 cmd->SCp.this_residual -= ms->data_ptr;
 615                 mesh_completed(ms, cmd);
 616         }
 617         if (start_next) {
 618                 out_8(&ms->mesh->sequence, SEQ_ENBRESEL);
 619                 mesh_flush_io(ms->mesh);
 620                 udelay(1);
 621                 ms->phase = idle;
 622                 mesh_start(ms);
 623         }
 624 }
 625 
 626 static inline void add_sdtr_msg(struct mesh_state *ms)
 627 {
 628         int i = ms->n_msgout;
 629 
 630         ms->msgout[i] = EXTENDED_MESSAGE;
 631         ms->msgout[i+1] = 3;
 632         ms->msgout[i+2] = EXTENDED_SDTR;
 633         ms->msgout[i+3] = mesh_sync_period/4;
 634         ms->msgout[i+4] = (ALLOW_SYNC(ms->conn_tgt)? mesh_sync_offset: 0);
 635         ms->n_msgout = i + 5;
 636 }
 637 
 638 static void set_sdtr(struct mesh_state *ms, int period, int offset)
 639 {
 640         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 641         volatile struct mesh_regs __iomem *mr = ms->mesh;
 642         int v, tr;
 643 
 644         tp->sdtr_state = sdtr_done;
 645         if (offset == 0) {
 646                 /* asynchronous */
 647                 if (SYNC_OFF(tp->sync_params))
 648                         printk(KERN_INFO "mesh: target %d now asynchronous\n",
 649                                ms->conn_tgt);
 650                 tp->sync_params = ASYNC_PARAMS;
 651                 out_8(&mr->sync_params, ASYNC_PARAMS);
 652                 return;
 653         }
 654         /*
 655          * We need to compute ceil(clk_freq * period / 500e6) - 2
 656          * without incurring overflow.
 657          */
 658         v = (ms->clk_freq / 5000) * period;
 659         if (v <= 250000) {
 660                 /* special case: sync_period == 5 * clk_period */
 661                 v = 0;
 662                 /* units of tr are 100kB/s */
 663                 tr = (ms->clk_freq + 250000) / 500000;
 664         } else {
 665                 /* sync_period == (v + 2) * 2 * clk_period */
 666                 v = (v + 99999) / 100000 - 2;
 667                 if (v > 15)
 668                         v = 15; /* oops */
 669                 tr = ((ms->clk_freq / (v + 2)) + 199999) / 200000;
 670         }
 671         if (offset > 15)
 672                 offset = 15;    /* can't happen */
 673         tp->sync_params = SYNC_PARAMS(offset, v);
 674         out_8(&mr->sync_params, tp->sync_params);
 675         printk(KERN_INFO "mesh: target %d synchronous at %d.%d MB/s\n",
 676                ms->conn_tgt, tr/10, tr%10);
 677 }
 678 
 679 static void start_phase(struct mesh_state *ms)
 680 {
 681         int i, seq, nb;
 682         volatile struct mesh_regs __iomem *mr = ms->mesh;
 683         volatile struct dbdma_regs __iomem *md = ms->dma;
 684         struct scsi_cmnd *cmd = ms->current_req;
 685         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
 686 
 687         dlog(ms, "start_phase nmo/exc/fc/seq = %.8x",
 688              MKWORD(ms->n_msgout, mr->exception, mr->fifo_count, mr->sequence));
 689         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 690         seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
 691         switch (ms->msgphase) {
 692         case msg_none:
 693                 break;
 694 
 695         case msg_in:
 696                 out_8(&mr->count_hi, 0);
 697                 out_8(&mr->count_lo, 1);
 698                 out_8(&mr->sequence, SEQ_MSGIN + seq);
 699                 ms->n_msgin = 0;
 700                 return;
 701 
 702         case msg_out:
 703                 /*
 704                  * To make sure ATN drops before we assert ACK for
 705                  * the last byte of the message, we have to do the
 706                  * last byte specially.
 707                  */
 708                 if (ms->n_msgout <= 0) {
 709                         printk(KERN_ERR "mesh: msg_out but n_msgout=%d\n",
 710                                ms->n_msgout);
 711                         mesh_dump_regs(ms);
 712                         ms->msgphase = msg_none;
 713                         break;
 714                 }
 715                 if (ALLOW_DEBUG(ms->conn_tgt)) {
 716                         printk(KERN_DEBUG "mesh: sending %d msg bytes:",
 717                                ms->n_msgout);
 718                         for (i = 0; i < ms->n_msgout; ++i)
 719                                 printk(" %x", ms->msgout[i]);
 720                         printk("\n");
 721                 }
 722                 dlog(ms, "msgout msg=%.8x", MKWORD(ms->n_msgout, ms->msgout[0],
 723                                                 ms->msgout[1], ms->msgout[2]));
 724                 out_8(&mr->count_hi, 0);
 725                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
 726                 mesh_flush_io(mr);
 727                 udelay(1);
 728                 /*
 729                  * If ATN is not already asserted, we assert it, then
 730                  * issue a SEQ_MSGOUT to get the mesh to drop ACK.
 731                  */
 732                 if ((in_8(&mr->bus_status0) & BS0_ATN) == 0) {
 733                         dlog(ms, "bus0 was %.2x explicitly asserting ATN", mr->bus_status0);
 734                         out_8(&mr->bus_status0, BS0_ATN); /* explicit ATN */
 735                         mesh_flush_io(mr);
 736                         udelay(1);
 737                         out_8(&mr->count_lo, 1);
 738                         out_8(&mr->sequence, SEQ_MSGOUT + seq);
 739                         out_8(&mr->bus_status0, 0); /* release explicit ATN */
 740                         dlog(ms,"hace: after explicit ATN bus0=%.2x",mr->bus_status0);
 741                 }
 742                 if (ms->n_msgout == 1) {
 743                         /*
 744                          * We can't issue the SEQ_MSGOUT without ATN
 745                          * until the target has asserted REQ.  The logic
 746                          * in cmd_complete handles both situations:
 747                          * REQ already asserted or not.
 748                          */
 749                         cmd_complete(ms);
 750                 } else {
 751                         out_8(&mr->count_lo, ms->n_msgout - 1);
 752                         out_8(&mr->sequence, SEQ_MSGOUT + seq);
 753                         for (i = 0; i < ms->n_msgout - 1; ++i)
 754                                 out_8(&mr->fifo, ms->msgout[i]);
 755                 }
 756                 return;
 757 
 758         default:
 759                 printk(KERN_ERR "mesh bug: start_phase msgphase=%d\n",
 760                        ms->msgphase);
 761         }
 762 
 763         switch (ms->phase) {
 764         case selecting:
 765                 out_8(&mr->dest_id, ms->conn_tgt);
 766                 out_8(&mr->sequence, SEQ_SELECT + SEQ_ATN);
 767                 break;
 768         case commanding:
 769                 out_8(&mr->sync_params, tp->sync_params);
 770                 out_8(&mr->count_hi, 0);
 771                 if (cmd) {
 772                         out_8(&mr->count_lo, cmd->cmd_len);
 773                         out_8(&mr->sequence, SEQ_COMMAND + seq);
 774                         for (i = 0; i < cmd->cmd_len; ++i)
 775                                 out_8(&mr->fifo, cmd->cmnd[i]);
 776                 } else {
 777                         out_8(&mr->count_lo, 6);
 778                         out_8(&mr->sequence, SEQ_COMMAND + seq);
 779                         for (i = 0; i < 6; ++i)
 780                                 out_8(&mr->fifo, 0);
 781                 }
 782                 break;
 783         case dataing:
 784                 /* transfer data, if any */
 785                 if (!ms->dma_started) {
 786                         set_dma_cmds(ms, cmd);
 787                         out_le32(&md->cmdptr, virt_to_phys(ms->dma_cmds));
 788                         out_le32(&md->control, (RUN << 16) | RUN);
 789                         ms->dma_started = 1;
 790                 }
 791                 nb = ms->dma_count;
 792                 if (nb > 0xfff0)
 793                         nb = 0xfff0;
 794                 ms->dma_count -= nb;
 795                 ms->data_ptr += nb;
 796                 out_8(&mr->count_lo, nb);
 797                 out_8(&mr->count_hi, nb >> 8);
 798                 out_8(&mr->sequence, (tp->data_goes_out?
 799                                 SEQ_DATAOUT: SEQ_DATAIN) + SEQ_DMA_MODE + seq);
 800                 break;
 801         case statusing:
 802                 out_8(&mr->count_hi, 0);
 803                 out_8(&mr->count_lo, 1);
 804                 out_8(&mr->sequence, SEQ_STATUS + seq);
 805                 break;
 806         case busfreeing:
 807         case disconnecting:
 808                 out_8(&mr->sequence, SEQ_ENBRESEL);
 809                 mesh_flush_io(mr);
 810                 udelay(1);
 811                 dlog(ms, "enbresel intr/exc/err/fc=%.8x",
 812                      MKWORD(mr->interrupt, mr->exception, mr->error,
 813                             mr->fifo_count));
 814                 out_8(&mr->sequence, SEQ_BUSFREE);
 815                 break;
 816         default:
 817                 printk(KERN_ERR "mesh: start_phase called with phase=%d\n",
 818                        ms->phase);
 819                 dumpslog(ms);
 820         }
 821 
 822 }
 823 
 824 static inline void get_msgin(struct mesh_state *ms)
 825 {
 826         volatile struct mesh_regs __iomem *mr = ms->mesh;
 827         int i, n;
 828 
 829         n = mr->fifo_count;
 830         if (n != 0) {
 831                 i = ms->n_msgin;
 832                 ms->n_msgin = i + n;
 833                 for (; n > 0; --n)
 834                         ms->msgin[i++] = in_8(&mr->fifo);
 835         }
 836 }
 837 
 838 static inline int msgin_length(struct mesh_state *ms)
 839 {
 840         int b, n;
 841 
 842         n = 1;
 843         if (ms->n_msgin > 0) {
 844                 b = ms->msgin[0];
 845                 if (b == 1) {
 846                         /* extended message */
 847                         n = ms->n_msgin < 2? 2: ms->msgin[1] + 2;
 848                 } else if (0x20 <= b && b <= 0x2f) {
 849                         /* 2-byte message */
 850                         n = 2;
 851                 }
 852         }
 853         return n;
 854 }
 855 
 856 static void reselected(struct mesh_state *ms)
 857 {
 858         volatile struct mesh_regs __iomem *mr = ms->mesh;
 859         struct scsi_cmnd *cmd;
 860         struct mesh_target *tp;
 861         int b, t, prev;
 862 
 863         switch (ms->phase) {
 864         case idle:
 865                 break;
 866         case arbitrating:
 867                 if ((cmd = ms->current_req) != NULL) {
 868                         /* put the command back on the queue */
 869                         cmd->host_scribble = (void *) ms->request_q;
 870                         if (ms->request_q == NULL)
 871                                 ms->request_qtail = cmd;
 872                         ms->request_q = cmd;
 873                         tp = &ms->tgts[cmd->device->id];
 874                         tp->current_req = NULL;
 875                 }
 876                 break;
 877         case busfreeing:
 878                 ms->phase = reselecting;
 879                 mesh_done(ms, 0);
 880                 break;
 881         case disconnecting:
 882                 break;
 883         default:
 884                 printk(KERN_ERR "mesh: reselected in phase %d/%d tgt %d\n",
 885                        ms->msgphase, ms->phase, ms->conn_tgt);
 886                 dumplog(ms, ms->conn_tgt);
 887                 dumpslog(ms);
 888         }
 889 
 890         if (ms->dma_started) {
 891                 printk(KERN_ERR "mesh: reselected with DMA started !\n");
 892                 halt_dma(ms);
 893         }
 894         ms->current_req = NULL;
 895         ms->phase = dataing;
 896         ms->msgphase = msg_in;
 897         ms->n_msgout = 0;
 898         ms->last_n_msgout = 0;
 899         prev = ms->conn_tgt;
 900 
 901         /*
 902          * We seem to get abortive reselections sometimes.
 903          */
 904         while ((in_8(&mr->bus_status1) & BS1_BSY) == 0) {
 905                 static int mesh_aborted_resels;
 906                 mesh_aborted_resels++;
 907                 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 908                 mesh_flush_io(mr);
 909                 udelay(1);
 910                 out_8(&mr->sequence, SEQ_ENBRESEL);
 911                 mesh_flush_io(mr);
 912                 udelay(5);
 913                 dlog(ms, "extra resel err/exc/fc = %.6x",
 914                      MKWORD(0, mr->error, mr->exception, mr->fifo_count));
 915         }
 916         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
 917         mesh_flush_io(mr);
 918         udelay(1);
 919         out_8(&mr->sequence, SEQ_ENBRESEL);
 920         mesh_flush_io(mr);
 921         udelay(1);
 922         out_8(&mr->sync_params, ASYNC_PARAMS);
 923 
 924         /*
 925          * Find out who reselected us.
 926          */
 927         if (in_8(&mr->fifo_count) == 0) {
 928                 printk(KERN_ERR "mesh: reselection but nothing in fifo?\n");
 929                 ms->conn_tgt = ms->host->this_id;
 930                 goto bogus;
 931         }
 932         /* get the last byte in the fifo */
 933         do {
 934                 b = in_8(&mr->fifo);
 935                 dlog(ms, "reseldata %x", b);
 936         } while (in_8(&mr->fifo_count));
 937         for (t = 0; t < 8; ++t)
 938                 if ((b & (1 << t)) != 0 && t != ms->host->this_id)
 939                         break;
 940         if (b != (1 << t) + (1 << ms->host->this_id)) {
 941                 printk(KERN_ERR "mesh: bad reselection data %x\n", b);
 942                 ms->conn_tgt = ms->host->this_id;
 943                 goto bogus;
 944         }
 945 
 946 
 947         /*
 948          * Set up to continue with that target's transfer.
 949          */
 950         ms->conn_tgt = t;
 951         tp = &ms->tgts[t];
 952         out_8(&mr->sync_params, tp->sync_params);
 953         if (ALLOW_DEBUG(t)) {
 954                 printk(KERN_DEBUG "mesh: reselected by target %d\n", t);
 955                 printk(KERN_DEBUG "mesh: saved_ptr=%x goes_out=%d cmd=%p\n",
 956                        tp->saved_ptr, tp->data_goes_out, tp->current_req);
 957         }
 958         ms->current_req = tp->current_req;
 959         if (tp->current_req == NULL) {
 960                 printk(KERN_ERR "mesh: reselected by tgt %d but no cmd!\n", t);
 961                 goto bogus;
 962         }
 963         ms->data_ptr = tp->saved_ptr;
 964         dlog(ms, "resel prev tgt=%d", prev);
 965         dlog(ms, "resel err/exc=%.4x", MKWORD(0, 0, mr->error, mr->exception));
 966         start_phase(ms);
 967         return;
 968 
 969 bogus:
 970         dumplog(ms, ms->conn_tgt);
 971         dumpslog(ms);
 972         ms->data_ptr = 0;
 973         ms->aborting = 1;
 974         start_phase(ms);
 975 }
 976 
 977 static void do_abort(struct mesh_state *ms)
 978 {
 979         ms->msgout[0] = ABORT;
 980         ms->n_msgout = 1;
 981         ms->aborting = 1;
 982         ms->stat = DID_ABORT;
 983         dlog(ms, "abort", 0);
 984 }
 985 
 986 static void handle_reset(struct mesh_state *ms)
 987 {
 988         int tgt;
 989         struct mesh_target *tp;
 990         struct scsi_cmnd *cmd;
 991         volatile struct mesh_regs __iomem *mr = ms->mesh;
 992 
 993         for (tgt = 0; tgt < 8; ++tgt) {
 994                 tp = &ms->tgts[tgt];
 995                 if ((cmd = tp->current_req) != NULL) {
 996                         cmd->result = DID_RESET << 16;
 997                         tp->current_req = NULL;
 998                         mesh_completed(ms, cmd);
 999                 }
1000                 ms->tgts[tgt].sdtr_state = do_sdtr;
1001                 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
1002         }
1003         ms->current_req = NULL;
1004         while ((cmd = ms->request_q) != NULL) {
1005                 ms->request_q = (struct scsi_cmnd *) cmd->host_scribble;
1006                 cmd->result = DID_RESET << 16;
1007                 mesh_completed(ms, cmd);
1008         }
1009         ms->phase = idle;
1010         ms->msgphase = msg_none;
1011         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1012         out_8(&mr->sequence, SEQ_FLUSHFIFO);
1013         mesh_flush_io(mr);
1014         udelay(1);
1015         out_8(&mr->sync_params, ASYNC_PARAMS);
1016         out_8(&mr->sequence, SEQ_ENBRESEL);
1017 }
1018 
1019 static irqreturn_t do_mesh_interrupt(int irq, void *dev_id)
1020 {
1021         unsigned long flags;
1022         struct mesh_state *ms = dev_id;
1023         struct Scsi_Host *dev = ms->host;
1024         
1025         spin_lock_irqsave(dev->host_lock, flags);
1026         mesh_interrupt(ms);
1027         spin_unlock_irqrestore(dev->host_lock, flags);
1028         return IRQ_HANDLED;
1029 }
1030 
1031 static void handle_error(struct mesh_state *ms)
1032 {
1033         int err, exc, count;
1034         volatile struct mesh_regs __iomem *mr = ms->mesh;
1035 
1036         err = in_8(&mr->error);
1037         exc = in_8(&mr->exception);
1038         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1039         dlog(ms, "error err/exc/fc/cl=%.8x",
1040              MKWORD(err, exc, mr->fifo_count, mr->count_lo));
1041         if (err & ERR_SCSIRESET) {
1042                 /* SCSI bus was reset */
1043                 printk(KERN_INFO "mesh: SCSI bus reset detected: "
1044                        "waiting for end...");
1045                 while ((in_8(&mr->bus_status1) & BS1_RST) != 0)
1046                         udelay(1);
1047                 printk("done\n");
1048                 handle_reset(ms);
1049                 /* request_q is empty, no point in mesh_start() */
1050                 return;
1051         }
1052         if (err & ERR_UNEXPDISC) {
1053                 /* Unexpected disconnect */
1054                 if (exc & EXC_RESELECTED) {
1055                         reselected(ms);
1056                         return;
1057                 }
1058                 if (!ms->aborting) {
1059                         printk(KERN_WARNING "mesh: target %d aborted\n",
1060                                ms->conn_tgt);
1061                         dumplog(ms, ms->conn_tgt);
1062                         dumpslog(ms);
1063                 }
1064                 out_8(&mr->interrupt, INT_CMDDONE);
1065                 ms->stat = DID_ABORT;
1066                 mesh_done(ms, 1);
1067                 return;
1068         }
1069         if (err & ERR_PARITY) {
1070                 if (ms->msgphase == msg_in) {
1071                         printk(KERN_ERR "mesh: msg parity error, target %d\n",
1072                                ms->conn_tgt);
1073                         ms->msgout[0] = MSG_PARITY_ERROR;
1074                         ms->n_msgout = 1;
1075                         ms->msgphase = msg_in_bad;
1076                         cmd_complete(ms);
1077                         return;
1078                 }
1079                 if (ms->stat == DID_OK) {
1080                         printk(KERN_ERR "mesh: parity error, target %d\n",
1081                                ms->conn_tgt);
1082                         ms->stat = DID_PARITY;
1083                 }
1084                 count = (mr->count_hi << 8) + mr->count_lo;
1085                 if (count == 0) {
1086                         cmd_complete(ms);
1087                 } else {
1088                         /* reissue the data transfer command */
1089                         out_8(&mr->sequence, mr->sequence);
1090                 }
1091                 return;
1092         }
1093         if (err & ERR_SEQERR) {
1094                 if (exc & EXC_RESELECTED) {
1095                         /* This can happen if we issue a command to
1096                            get the bus just after the target reselects us. */
1097                         static int mesh_resel_seqerr;
1098                         mesh_resel_seqerr++;
1099                         reselected(ms);
1100                         return;
1101                 }
1102                 if (exc == EXC_PHASEMM) {
1103                         static int mesh_phasemm_seqerr;
1104                         mesh_phasemm_seqerr++;
1105                         phase_mismatch(ms);
1106                         return;
1107                 }
1108                 printk(KERN_ERR "mesh: sequence error (err=%x exc=%x)\n",
1109                        err, exc);
1110         } else {
1111                 printk(KERN_ERR "mesh: unknown error %x (exc=%x)\n", err, exc);
1112         }
1113         mesh_dump_regs(ms);
1114         dumplog(ms, ms->conn_tgt);
1115         if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) {
1116                 /* try to do what the target wants */
1117                 do_abort(ms);
1118                 phase_mismatch(ms);
1119                 return;
1120         }
1121         ms->stat = DID_ERROR;
1122         mesh_done(ms, 1);
1123 }
1124 
1125 static void handle_exception(struct mesh_state *ms)
1126 {
1127         int exc;
1128         volatile struct mesh_regs __iomem *mr = ms->mesh;
1129 
1130         exc = in_8(&mr->exception);
1131         out_8(&mr->interrupt, INT_EXCEPTION | INT_CMDDONE);
1132         if (exc & EXC_RESELECTED) {
1133                 static int mesh_resel_exc;
1134                 mesh_resel_exc++;
1135                 reselected(ms);
1136         } else if (exc == EXC_ARBLOST) {
1137                 printk(KERN_DEBUG "mesh: lost arbitration\n");
1138                 ms->stat = DID_BUS_BUSY;
1139                 mesh_done(ms, 1);
1140         } else if (exc == EXC_SELTO) {
1141                 /* selection timed out */
1142                 ms->stat = DID_BAD_TARGET;
1143                 mesh_done(ms, 1);
1144         } else if (exc == EXC_PHASEMM) {
1145                 /* target wants to do something different:
1146                    find out what it wants and do it. */
1147                 phase_mismatch(ms);
1148         } else {
1149                 printk(KERN_ERR "mesh: can't cope with exception %x\n", exc);
1150                 mesh_dump_regs(ms);
1151                 dumplog(ms, ms->conn_tgt);
1152                 do_abort(ms);
1153                 phase_mismatch(ms);
1154         }
1155 }
1156 
1157 static void handle_msgin(struct mesh_state *ms)
1158 {
1159         int i, code;
1160         struct scsi_cmnd *cmd = ms->current_req;
1161         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1162 
1163         if (ms->n_msgin == 0)
1164                 return;
1165         code = ms->msgin[0];
1166         if (ALLOW_DEBUG(ms->conn_tgt)) {
1167                 printk(KERN_DEBUG "got %d message bytes:", ms->n_msgin);
1168                 for (i = 0; i < ms->n_msgin; ++i)
1169                         printk(" %x", ms->msgin[i]);
1170                 printk("\n");
1171         }
1172         dlog(ms, "msgin msg=%.8x",
1173              MKWORD(ms->n_msgin, code, ms->msgin[1], ms->msgin[2]));
1174 
1175         ms->expect_reply = 0;
1176         ms->n_msgout = 0;
1177         if (ms->n_msgin < msgin_length(ms))
1178                 goto reject;
1179         if (cmd)
1180                 cmd->SCp.Message = code;
1181         switch (code) {
1182         case COMMAND_COMPLETE:
1183                 break;
1184         case EXTENDED_MESSAGE:
1185                 switch (ms->msgin[2]) {
1186                 case EXTENDED_MODIFY_DATA_POINTER:
1187                         ms->data_ptr += (ms->msgin[3] << 24) + ms->msgin[6]
1188                                 + (ms->msgin[4] << 16) + (ms->msgin[5] << 8);
1189                         break;
1190                 case EXTENDED_SDTR:
1191                         if (tp->sdtr_state != sdtr_sent) {
1192                                 /* reply with an SDTR */
1193                                 add_sdtr_msg(ms);
1194                                 /* limit period to at least his value,
1195                                    offset to no more than his */
1196                                 if (ms->msgout[3] < ms->msgin[3])
1197                                         ms->msgout[3] = ms->msgin[3];
1198                                 if (ms->msgout[4] > ms->msgin[4])
1199                                         ms->msgout[4] = ms->msgin[4];
1200                                 set_sdtr(ms, ms->msgout[3], ms->msgout[4]);
1201                                 ms->msgphase = msg_out;
1202                         } else {
1203                                 set_sdtr(ms, ms->msgin[3], ms->msgin[4]);
1204                         }
1205                         break;
1206                 default:
1207                         goto reject;
1208                 }
1209                 break;
1210         case SAVE_POINTERS:
1211                 tp->saved_ptr = ms->data_ptr;
1212                 break;
1213         case RESTORE_POINTERS:
1214                 ms->data_ptr = tp->saved_ptr;
1215                 break;
1216         case DISCONNECT:
1217                 ms->phase = disconnecting;
1218                 break;
1219         case ABORT:
1220                 break;
1221         case MESSAGE_REJECT:
1222                 if (tp->sdtr_state == sdtr_sent)
1223                         set_sdtr(ms, 0, 0);
1224                 break;
1225         case NOP:
1226                 break;
1227         default:
1228                 if (IDENTIFY_BASE <= code && code <= IDENTIFY_BASE + 7) {
1229                         if (cmd == NULL) {
1230                                 do_abort(ms);
1231                                 ms->msgphase = msg_out;
1232                         } else if (code != cmd->device->lun + IDENTIFY_BASE) {
1233                                 printk(KERN_WARNING "mesh: lun mismatch "
1234                                        "(%d != %llu) on reselection from "
1235                                        "target %d\n", code - IDENTIFY_BASE,
1236                                        cmd->device->lun, ms->conn_tgt);
1237                         }
1238                         break;
1239                 }
1240                 goto reject;
1241         }
1242         return;
1243 
1244  reject:
1245         printk(KERN_WARNING "mesh: rejecting message from target %d:",
1246                ms->conn_tgt);
1247         for (i = 0; i < ms->n_msgin; ++i)
1248                 printk(" %x", ms->msgin[i]);
1249         printk("\n");
1250         ms->msgout[0] = MESSAGE_REJECT;
1251         ms->n_msgout = 1;
1252         ms->msgphase = msg_out;
1253 }
1254 
1255 /*
1256  * Set up DMA commands for transferring data.
1257  */
1258 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd)
1259 {
1260         int i, dma_cmd, total, off, dtot;
1261         struct scatterlist *scl;
1262         struct dbdma_cmd *dcmds;
1263 
1264         dma_cmd = ms->tgts[ms->conn_tgt].data_goes_out?
1265                 OUTPUT_MORE: INPUT_MORE;
1266         dcmds = ms->dma_cmds;
1267         dtot = 0;
1268         if (cmd) {
1269                 int nseg;
1270 
1271                 cmd->SCp.this_residual = scsi_bufflen(cmd);
1272 
1273                 nseg = scsi_dma_map(cmd);
1274                 BUG_ON(nseg < 0);
1275 
1276                 if (nseg) {
1277                         total = 0;
1278                         off = ms->data_ptr;
1279 
1280                         scsi_for_each_sg(cmd, scl, nseg, i) {
1281                                 u32 dma_addr = sg_dma_address(scl);
1282                                 u32 dma_len = sg_dma_len(scl);
1283                                 
1284                                 total += scl->length;
1285                                 if (off >= dma_len) {
1286                                         off -= dma_len;
1287                                         continue;
1288                                 }
1289                                 if (dma_len > 0xffff)
1290                                         panic("mesh: scatterlist element >= 64k");
1291                                 dcmds->req_count = cpu_to_le16(dma_len - off);
1292                                 dcmds->command = cpu_to_le16(dma_cmd);
1293                                 dcmds->phy_addr = cpu_to_le32(dma_addr + off);
1294                                 dcmds->xfer_status = 0;
1295                                 ++dcmds;
1296                                 dtot += dma_len - off;
1297                                 off = 0;
1298                         }
1299                 }
1300         }
1301         if (dtot == 0) {
1302                 /* Either the target has overrun our buffer,
1303                    or the caller didn't provide a buffer. */
1304                 static char mesh_extra_buf[64];
1305 
1306                 dtot = sizeof(mesh_extra_buf);
1307                 dcmds->req_count = cpu_to_le16(dtot);
1308                 dcmds->phy_addr = cpu_to_le32(virt_to_phys(mesh_extra_buf));
1309                 dcmds->xfer_status = 0;
1310                 ++dcmds;
1311         }
1312         dma_cmd += OUTPUT_LAST - OUTPUT_MORE;
1313         dcmds[-1].command = cpu_to_le16(dma_cmd);
1314         memset(dcmds, 0, sizeof(*dcmds));
1315         dcmds->command = cpu_to_le16(DBDMA_STOP);
1316         ms->dma_count = dtot;
1317 }
1318 
1319 static void halt_dma(struct mesh_state *ms)
1320 {
1321         volatile struct dbdma_regs __iomem *md = ms->dma;
1322         volatile struct mesh_regs __iomem *mr = ms->mesh;
1323         struct scsi_cmnd *cmd = ms->current_req;
1324         int t, nb;
1325 
1326         if (!ms->tgts[ms->conn_tgt].data_goes_out) {
1327                 /* wait a little while until the fifo drains */
1328                 t = 50;
1329                 while (t > 0 && in_8(&mr->fifo_count) != 0
1330                        && (in_le32(&md->status) & ACTIVE) != 0) {
1331                         --t;
1332                         udelay(1);
1333                 }
1334         }
1335         out_le32(&md->control, RUN << 16);      /* turn off RUN bit */
1336         nb = (mr->count_hi << 8) + mr->count_lo;
1337         dlog(ms, "halt_dma fc/count=%.6x",
1338              MKWORD(0, mr->fifo_count, 0, nb));
1339         if (ms->tgts[ms->conn_tgt].data_goes_out)
1340                 nb += mr->fifo_count;
1341         /* nb is the number of bytes not yet transferred
1342            to/from the target. */
1343         ms->data_ptr -= nb;
1344         dlog(ms, "data_ptr %x", ms->data_ptr);
1345         if (ms->data_ptr < 0) {
1346                 printk(KERN_ERR "mesh: halt_dma: data_ptr=%d (nb=%d, ms=%p)\n",
1347                        ms->data_ptr, nb, ms);
1348                 ms->data_ptr = 0;
1349 #ifdef MESH_DBG
1350                 dumplog(ms, ms->conn_tgt);
1351                 dumpslog(ms);
1352 #endif /* MESH_DBG */
1353         } else if (cmd && scsi_bufflen(cmd) &&
1354                    ms->data_ptr > scsi_bufflen(cmd)) {
1355                 printk(KERN_DEBUG "mesh: target %d overrun, "
1356                        "data_ptr=%x total=%x goes_out=%d\n",
1357                        ms->conn_tgt, ms->data_ptr, scsi_bufflen(cmd),
1358                        ms->tgts[ms->conn_tgt].data_goes_out);
1359         }
1360         scsi_dma_unmap(cmd);
1361         ms->dma_started = 0;
1362 }
1363 
1364 static void phase_mismatch(struct mesh_state *ms)
1365 {
1366         volatile struct mesh_regs __iomem *mr = ms->mesh;
1367         int phase;
1368 
1369         dlog(ms, "phasemm ch/cl/seq/fc=%.8x",
1370              MKWORD(mr->count_hi, mr->count_lo, mr->sequence, mr->fifo_count));
1371         phase = in_8(&mr->bus_status0) & BS0_PHASE;
1372         if (ms->msgphase == msg_out_xxx && phase == BP_MSGOUT) {
1373                 /* output the last byte of the message, without ATN */
1374                 out_8(&mr->count_lo, 1);
1375                 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1376                 mesh_flush_io(mr);
1377                 udelay(1);
1378                 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1379                 ms->msgphase = msg_out_last;
1380                 return;
1381         }
1382 
1383         if (ms->msgphase == msg_in) {
1384                 get_msgin(ms);
1385                 if (ms->n_msgin)
1386                         handle_msgin(ms);
1387         }
1388 
1389         if (ms->dma_started)
1390                 halt_dma(ms);
1391         if (mr->fifo_count) {
1392                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1393                 mesh_flush_io(mr);
1394                 udelay(1);
1395         }
1396 
1397         ms->msgphase = msg_none;
1398         switch (phase) {
1399         case BP_DATAIN:
1400                 ms->tgts[ms->conn_tgt].data_goes_out = 0;
1401                 ms->phase = dataing;
1402                 break;
1403         case BP_DATAOUT:
1404                 ms->tgts[ms->conn_tgt].data_goes_out = 1;
1405                 ms->phase = dataing;
1406                 break;
1407         case BP_COMMAND:
1408                 ms->phase = commanding;
1409                 break;
1410         case BP_STATUS:
1411                 ms->phase = statusing;
1412                 break;
1413         case BP_MSGIN:
1414                 ms->msgphase = msg_in;
1415                 ms->n_msgin = 0;
1416                 break;
1417         case BP_MSGOUT:
1418                 ms->msgphase = msg_out;
1419                 if (ms->n_msgout == 0) {
1420                         if (ms->aborting) {
1421                                 do_abort(ms);
1422                         } else {
1423                                 if (ms->last_n_msgout == 0) {
1424                                         printk(KERN_DEBUG
1425                                                "mesh: no msg to repeat\n");
1426                                         ms->msgout[0] = NOP;
1427                                         ms->last_n_msgout = 1;
1428                                 }
1429                                 ms->n_msgout = ms->last_n_msgout;
1430                         }
1431                 }
1432                 break;
1433         default:
1434                 printk(KERN_DEBUG "mesh: unknown scsi phase %x\n", phase);
1435                 ms->stat = DID_ERROR;
1436                 mesh_done(ms, 1);
1437                 return;
1438         }
1439 
1440         start_phase(ms);
1441 }
1442 
1443 static void cmd_complete(struct mesh_state *ms)
1444 {
1445         volatile struct mesh_regs __iomem *mr = ms->mesh;
1446         struct scsi_cmnd *cmd = ms->current_req;
1447         struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1448         int seq, n, t;
1449 
1450         dlog(ms, "cmd_complete fc=%x", mr->fifo_count);
1451         seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
1452         switch (ms->msgphase) {
1453         case msg_out_xxx:
1454                 /* huh?  we expected a phase mismatch */
1455                 ms->n_msgin = 0;
1456                 ms->msgphase = msg_in;
1457                 /* fall through */
1458 
1459         case msg_in:
1460                 /* should have some message bytes in fifo */
1461                 get_msgin(ms);
1462                 n = msgin_length(ms);
1463                 if (ms->n_msgin < n) {
1464                         out_8(&mr->count_lo, n - ms->n_msgin);
1465                         out_8(&mr->sequence, SEQ_MSGIN + seq);
1466                 } else {
1467                         ms->msgphase = msg_none;
1468                         handle_msgin(ms);
1469                         start_phase(ms);
1470                 }
1471                 break;
1472 
1473         case msg_in_bad:
1474                 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1475                 mesh_flush_io(mr);
1476                 udelay(1);
1477                 out_8(&mr->count_lo, 1);
1478                 out_8(&mr->sequence, SEQ_MSGIN + SEQ_ATN + use_active_neg);
1479                 break;
1480 
1481         case msg_out:
1482                 /*
1483                  * To get the right timing on ATN wrt ACK, we have
1484                  * to get the MESH to drop ACK, wait until REQ gets
1485                  * asserted, then drop ATN.  To do this we first
1486                  * issue a SEQ_MSGOUT with ATN and wait for REQ,
1487                  * then change the command to a SEQ_MSGOUT w/o ATN.
1488                  * If we don't see REQ in a reasonable time, we
1489                  * change the command to SEQ_MSGIN with ATN,
1490                  * wait for the phase mismatch interrupt, then
1491                  * issue the SEQ_MSGOUT without ATN.
1492                  */
1493                 out_8(&mr->count_lo, 1);
1494                 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg + SEQ_ATN);
1495                 t = 30;         /* wait up to 30us */
1496                 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0 && --t >= 0)
1497                         udelay(1);
1498                 dlog(ms, "last_mbyte err/exc/fc/cl=%.8x",
1499                      MKWORD(mr->error, mr->exception,
1500                             mr->fifo_count, mr->count_lo));
1501                 if (in_8(&mr->interrupt) & (INT_ERROR | INT_EXCEPTION)) {
1502                         /* whoops, target didn't do what we expected */
1503                         ms->last_n_msgout = ms->n_msgout;
1504                         ms->n_msgout = 0;
1505                         if (in_8(&mr->interrupt) & INT_ERROR) {
1506                                 printk(KERN_ERR "mesh: error %x in msg_out\n",
1507                                        in_8(&mr->error));
1508                                 handle_error(ms);
1509                                 return;
1510                         }
1511                         if (in_8(&mr->exception) != EXC_PHASEMM)
1512                                 printk(KERN_ERR "mesh: exc %x in msg_out\n",
1513                                        in_8(&mr->exception));
1514                         else
1515                                 printk(KERN_DEBUG "mesh: bs0=%x in msg_out\n",
1516                                        in_8(&mr->bus_status0));
1517                         handle_exception(ms);
1518                         return;
1519                 }
1520                 if (in_8(&mr->bus_status0) & BS0_REQ) {
1521                         out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1522                         mesh_flush_io(mr);
1523                         udelay(1);
1524                         out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1525                         ms->msgphase = msg_out_last;
1526                 } else {
1527                         out_8(&mr->sequence, SEQ_MSGIN + use_active_neg + SEQ_ATN);
1528                         ms->msgphase = msg_out_xxx;
1529                 }
1530                 break;
1531 
1532         case msg_out_last:
1533                 ms->last_n_msgout = ms->n_msgout;
1534                 ms->n_msgout = 0;
1535                 ms->msgphase = ms->expect_reply? msg_in: msg_none;
1536                 start_phase(ms);
1537                 break;
1538 
1539         case msg_none:
1540                 switch (ms->phase) {
1541                 case idle:
1542                         printk(KERN_ERR "mesh: interrupt in idle phase?\n");
1543                         dumpslog(ms);
1544                         return;
1545                 case selecting:
1546                         dlog(ms, "Selecting phase at command completion",0);
1547                         ms->msgout[0] = IDENTIFY(ALLOW_RESEL(ms->conn_tgt),
1548                                                  (cmd? cmd->device->lun: 0));
1549                         ms->n_msgout = 1;
1550                         ms->expect_reply = 0;
1551                         if (ms->aborting) {
1552                                 ms->msgout[0] = ABORT;
1553                                 ms->n_msgout++;
1554                         } else if (tp->sdtr_state == do_sdtr) {
1555                                 /* add SDTR message */
1556                                 add_sdtr_msg(ms);
1557                                 ms->expect_reply = 1;
1558                                 tp->sdtr_state = sdtr_sent;
1559                         }
1560                         ms->msgphase = msg_out;
1561                         /*
1562                          * We need to wait for REQ before dropping ATN.
1563                          * We wait for at most 30us, then fall back to
1564                          * a scheme where we issue a SEQ_COMMAND with ATN,
1565                          * which will give us a phase mismatch interrupt
1566                          * when REQ does come, and then we send the message.
1567                          */
1568                         t = 230;                /* wait up to 230us */
1569                         while ((in_8(&mr->bus_status0) & BS0_REQ) == 0) {
1570                                 if (--t < 0) {
1571                                         dlog(ms, "impatient for req", ms->n_msgout);
1572                                         ms->msgphase = msg_none;
1573                                         break;
1574                                 }
1575                                 udelay(1);
1576                         }
1577                         break;
1578                 case dataing:
1579                         if (ms->dma_count != 0) {
1580                                 start_phase(ms);
1581                                 return;
1582                         }
1583                         /*
1584                          * We can get a phase mismatch here if the target
1585                          * changes to the status phase, even though we have
1586                          * had a command complete interrupt.  Then, if we
1587                          * issue the SEQ_STATUS command, we'll get a sequence
1588                          * error interrupt.  Which isn't so bad except that
1589                          * occasionally the mesh actually executes the
1590                          * SEQ_STATUS *as well as* giving us the sequence
1591                          * error and phase mismatch exception.
1592                          */
1593                         out_8(&mr->sequence, 0);
1594                         out_8(&mr->interrupt,
1595                               INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1596                         halt_dma(ms);
1597                         break;
1598                 case statusing:
1599                         if (cmd) {
1600                                 cmd->SCp.Status = mr->fifo;
1601                                 if (DEBUG_TARGET(cmd))
1602                                         printk(KERN_DEBUG "mesh: status is %x\n",
1603                                                cmd->SCp.Status);
1604                         }
1605                         ms->msgphase = msg_in;
1606                         break;
1607                 case busfreeing:
1608                         mesh_done(ms, 1);
1609                         return;
1610                 case disconnecting:
1611                         ms->current_req = NULL;
1612                         ms->phase = idle;
1613                         mesh_start(ms);
1614                         return;
1615                 default:
1616                         break;
1617                 }
1618                 ++ms->phase;
1619                 start_phase(ms);
1620                 break;
1621         }
1622 }
1623 
1624 
1625 /*
1626  * Called by midlayer with host locked to queue a new
1627  * request
1628  */
1629 static int mesh_queue_lck(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *))
1630 {
1631         struct mesh_state *ms;
1632 
1633         cmd->scsi_done = done;
1634         cmd->host_scribble = NULL;
1635 
1636         ms = (struct mesh_state *) cmd->device->host->hostdata;
1637 
1638         if (ms->request_q == NULL)
1639                 ms->request_q = cmd;
1640         else
1641                 ms->request_qtail->host_scribble = (void *) cmd;
1642         ms->request_qtail = cmd;
1643 
1644         if (ms->phase == idle)
1645                 mesh_start(ms);
1646 
1647         return 0;
1648 }
1649 
1650 static DEF_SCSI_QCMD(mesh_queue)
1651 
1652 /*
1653  * Called to handle interrupts, either call by the interrupt
1654  * handler (do_mesh_interrupt) or by other functions in
1655  * exceptional circumstances
1656  */
1657 static void mesh_interrupt(struct mesh_state *ms)
1658 {
1659         volatile struct mesh_regs __iomem *mr = ms->mesh;
1660         int intr;
1661 
1662 #if 0
1663         if (ALLOW_DEBUG(ms->conn_tgt))
1664                 printk(KERN_DEBUG "mesh_intr, bs0=%x int=%x exc=%x err=%x "
1665                        "phase=%d msgphase=%d\n", mr->bus_status0,
1666                        mr->interrupt, mr->exception, mr->error,
1667                        ms->phase, ms->msgphase);
1668 #endif
1669         while ((intr = in_8(&mr->interrupt)) != 0) {
1670                 dlog(ms, "interrupt intr/err/exc/seq=%.8x", 
1671                      MKWORD(intr, mr->error, mr->exception, mr->sequence));
1672                 if (intr & INT_ERROR) {
1673                         handle_error(ms);
1674                 } else if (intr & INT_EXCEPTION) {
1675                         handle_exception(ms);
1676                 } else if (intr & INT_CMDDONE) {
1677                         out_8(&mr->interrupt, INT_CMDDONE);
1678                         cmd_complete(ms);
1679                 }
1680         }
1681 }
1682 
1683 /* Todo: here we can at least try to remove the command from the
1684  * queue if it isn't connected yet, and for pending command, assert
1685  * ATN until the bus gets freed.
1686  */
1687 static int mesh_abort(struct scsi_cmnd *cmd)
1688 {
1689         struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1690 
1691         printk(KERN_DEBUG "mesh_abort(%p)\n", cmd);
1692         mesh_dump_regs(ms);
1693         dumplog(ms, cmd->device->id);
1694         dumpslog(ms);
1695         return FAILED;
1696 }
1697 
1698 /*
1699  * Called by the midlayer with the lock held to reset the
1700  * SCSI host and bus.
1701  * The midlayer will wait for devices to come back, we don't need
1702  * to do that ourselves
1703  */
1704 static int mesh_host_reset(struct scsi_cmnd *cmd)
1705 {
1706         struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1707         volatile struct mesh_regs __iomem *mr = ms->mesh;
1708         volatile struct dbdma_regs __iomem *md = ms->dma;
1709         unsigned long flags;
1710 
1711         printk(KERN_DEBUG "mesh_host_reset\n");
1712 
1713         spin_lock_irqsave(ms->host->host_lock, flags);
1714 
1715         /* Reset the controller & dbdma channel */
1716         out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16);   /* stop dma */
1717         out_8(&mr->exception, 0xff);    /* clear all exception bits */
1718         out_8(&mr->error, 0xff);        /* clear all error bits */
1719         out_8(&mr->sequence, SEQ_RESETMESH);
1720         mesh_flush_io(mr);
1721         udelay(1);
1722         out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1723         out_8(&mr->source_id, ms->host->this_id);
1724         out_8(&mr->sel_timeout, 25);    /* 250ms */
1725         out_8(&mr->sync_params, ASYNC_PARAMS);
1726 
1727         /* Reset the bus */
1728         out_8(&mr->bus_status1, BS1_RST);       /* assert RST */
1729         mesh_flush_io(mr);
1730         udelay(30);                     /* leave it on for >= 25us */
1731         out_8(&mr->bus_status1, 0);     /* negate RST */
1732 
1733         /* Complete pending commands */
1734         handle_reset(ms);
1735         
1736         spin_unlock_irqrestore(ms->host->host_lock, flags);
1737         return SUCCESS;
1738 }
1739 
1740 static void set_mesh_power(struct mesh_state *ms, int state)
1741 {
1742         if (!machine_is(powermac))
1743                 return;
1744         if (state) {
1745                 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 1);
1746                 msleep(200);
1747         } else {
1748                 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 0);
1749                 msleep(10);
1750         }
1751 }
1752 
1753 
1754 #ifdef CONFIG_PM
1755 static int mesh_suspend(struct macio_dev *mdev, pm_message_t mesg)
1756 {
1757         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1758         unsigned long flags;
1759 
1760         switch (mesg.event) {
1761         case PM_EVENT_SUSPEND:
1762         case PM_EVENT_HIBERNATE:
1763         case PM_EVENT_FREEZE:
1764                 break;
1765         default:
1766                 return 0;
1767         }
1768         if (ms->phase == sleeping)
1769                 return 0;
1770 
1771         scsi_block_requests(ms->host);
1772         spin_lock_irqsave(ms->host->host_lock, flags);
1773         while(ms->phase != idle) {
1774                 spin_unlock_irqrestore(ms->host->host_lock, flags);
1775                 msleep(10);
1776                 spin_lock_irqsave(ms->host->host_lock, flags);
1777         }
1778         ms->phase = sleeping;
1779         spin_unlock_irqrestore(ms->host->host_lock, flags);
1780         disable_irq(ms->meshintr);
1781         set_mesh_power(ms, 0);
1782 
1783         return 0;
1784 }
1785 
1786 static int mesh_resume(struct macio_dev *mdev)
1787 {
1788         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1789         unsigned long flags;
1790 
1791         if (ms->phase != sleeping)
1792                 return 0;
1793 
1794         set_mesh_power(ms, 1);
1795         mesh_init(ms);
1796         spin_lock_irqsave(ms->host->host_lock, flags);
1797         mesh_start(ms);
1798         spin_unlock_irqrestore(ms->host->host_lock, flags);
1799         enable_irq(ms->meshintr);
1800         scsi_unblock_requests(ms->host);
1801 
1802         return 0;
1803 }
1804 
1805 #endif /* CONFIG_PM */
1806 
1807 /*
1808  * If we leave drives set for synchronous transfers (especially
1809  * CDROMs), and reboot to MacOS, it gets confused, poor thing.
1810  * So, on reboot we reset the SCSI bus.
1811  */
1812 static int mesh_shutdown(struct macio_dev *mdev)
1813 {
1814         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1815         volatile struct mesh_regs __iomem *mr;
1816         unsigned long flags;
1817 
1818         printk(KERN_INFO "resetting MESH scsi bus(es)\n");
1819         spin_lock_irqsave(ms->host->host_lock, flags);
1820         mr = ms->mesh;
1821         out_8(&mr->intr_mask, 0);
1822         out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1823         out_8(&mr->bus_status1, BS1_RST);
1824         mesh_flush_io(mr);
1825         udelay(30);
1826         out_8(&mr->bus_status1, 0);
1827         spin_unlock_irqrestore(ms->host->host_lock, flags);
1828 
1829         return 0;
1830 }
1831 
1832 static struct scsi_host_template mesh_template = {
1833         .proc_name                      = "mesh",
1834         .name                           = "MESH",
1835         .queuecommand                   = mesh_queue,
1836         .eh_abort_handler               = mesh_abort,
1837         .eh_host_reset_handler          = mesh_host_reset,
1838         .can_queue                      = 20,
1839         .this_id                        = 7,
1840         .sg_tablesize                   = SG_ALL,
1841         .cmd_per_lun                    = 2,
1842         .max_segment_size               = 65535,
1843 };
1844 
1845 static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match)
1846 {
1847         struct device_node *mesh = macio_get_of_node(mdev);
1848         struct pci_dev* pdev = macio_get_pci_dev(mdev);
1849         int tgt, minper;
1850         const int *cfp;
1851         struct mesh_state *ms;
1852         struct Scsi_Host *mesh_host;
1853         void *dma_cmd_space;
1854         dma_addr_t dma_cmd_bus;
1855 
1856         switch (mdev->bus->chip->type) {
1857         case macio_heathrow:
1858         case macio_gatwick:
1859         case macio_paddington:
1860                 use_active_neg = 0;
1861                 break;
1862         default:
1863                 use_active_neg = SEQ_ACTIVE_NEG;
1864         }
1865 
1866         if (macio_resource_count(mdev) != 2 || macio_irq_count(mdev) != 2) {
1867                 printk(KERN_ERR "mesh: expected 2 addrs and 2 intrs"
1868                        " (got %d,%d)\n", macio_resource_count(mdev),
1869                        macio_irq_count(mdev));
1870                 return -ENODEV;
1871         }
1872 
1873         if (macio_request_resources(mdev, "mesh") != 0) {
1874                 printk(KERN_ERR "mesh: unable to request memory resources");
1875                 return -EBUSY;
1876         }
1877         mesh_host = scsi_host_alloc(&mesh_template, sizeof(struct mesh_state));
1878         if (mesh_host == NULL) {
1879                 printk(KERN_ERR "mesh: couldn't register host");
1880                 goto out_release;
1881         }
1882         
1883         /* Old junk for root discovery, that will die ultimately */
1884 #if !defined(MODULE)
1885         note_scsi_host(mesh, mesh_host);
1886 #endif
1887 
1888         mesh_host->base = macio_resource_start(mdev, 0);
1889         mesh_host->irq = macio_irq(mdev, 0);
1890         ms = (struct mesh_state *) mesh_host->hostdata;
1891         macio_set_drvdata(mdev, ms);
1892         ms->host = mesh_host;
1893         ms->mdev = mdev;
1894         ms->pdev = pdev;
1895         
1896         ms->mesh = ioremap(macio_resource_start(mdev, 0), 0x1000);
1897         if (ms->mesh == NULL) {
1898                 printk(KERN_ERR "mesh: can't map registers\n");
1899                 goto out_free;
1900         }               
1901         ms->dma = ioremap(macio_resource_start(mdev, 1), 0x1000);
1902         if (ms->dma == NULL) {
1903                 printk(KERN_ERR "mesh: can't map registers\n");
1904                 iounmap(ms->mesh);
1905                 goto out_free;
1906         }
1907 
1908         ms->meshintr = macio_irq(mdev, 0);
1909         ms->dmaintr = macio_irq(mdev, 1);
1910 
1911         /* Space for dma command list: +1 for stop command,
1912          * +1 to allow for aligning.
1913          */
1914         ms->dma_cmd_size = (mesh_host->sg_tablesize + 2) * sizeof(struct dbdma_cmd);
1915 
1916         /* We use the PCI APIs for now until the generic one gets fixed
1917          * enough or until we get some macio-specific versions
1918          */
1919         dma_cmd_space = dma_alloc_coherent(&macio_get_pci_dev(mdev)->dev,
1920                                            ms->dma_cmd_size, &dma_cmd_bus,
1921                                            GFP_KERNEL);
1922         if (dma_cmd_space == NULL) {
1923                 printk(KERN_ERR "mesh: can't allocate DMA table\n");
1924                 goto out_unmap;
1925         }
1926 
1927         ms->dma_cmds = (struct dbdma_cmd *) DBDMA_ALIGN(dma_cmd_space);
1928         ms->dma_cmd_space = dma_cmd_space;
1929         ms->dma_cmd_bus = dma_cmd_bus + ((unsigned long)ms->dma_cmds)
1930                 - (unsigned long)dma_cmd_space;
1931         ms->current_req = NULL;
1932         for (tgt = 0; tgt < 8; ++tgt) {
1933                 ms->tgts[tgt].sdtr_state = do_sdtr;
1934                 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
1935                 ms->tgts[tgt].current_req = NULL;
1936         }
1937 
1938         if ((cfp = of_get_property(mesh, "clock-frequency", NULL)))
1939                 ms->clk_freq = *cfp;
1940         else {
1941                 printk(KERN_INFO "mesh: assuming 50MHz clock frequency\n");
1942                 ms->clk_freq = 50000000;
1943         }
1944 
1945         /* The maximum sync rate is clock / 5; increase
1946          * mesh_sync_period if necessary.
1947          */
1948         minper = 1000000000 / (ms->clk_freq / 5); /* ns */
1949         if (mesh_sync_period < minper)
1950                 mesh_sync_period = minper;
1951 
1952         /* Power up the chip */
1953         set_mesh_power(ms, 1);
1954 
1955         /* Set it up */
1956         mesh_init(ms);
1957 
1958         /* Request interrupt */
1959         if (request_irq(ms->meshintr, do_mesh_interrupt, 0, "MESH", ms)) {
1960                 printk(KERN_ERR "MESH: can't get irq %d\n", ms->meshintr);
1961                 goto out_shutdown;
1962         }
1963 
1964         /* Add scsi host & scan */
1965         if (scsi_add_host(mesh_host, &mdev->ofdev.dev))
1966                 goto out_release_irq;
1967         scsi_scan_host(mesh_host);
1968 
1969         return 0;
1970 
1971  out_release_irq:
1972         free_irq(ms->meshintr, ms);
1973  out_shutdown:
1974         /* shutdown & reset bus in case of error or macos can be confused
1975          * at reboot if the bus was set to synchronous mode already
1976          */
1977         mesh_shutdown(mdev);
1978         set_mesh_power(ms, 0);
1979         dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size,
1980                             ms->dma_cmd_space, ms->dma_cmd_bus);
1981  out_unmap:
1982         iounmap(ms->dma);
1983         iounmap(ms->mesh);
1984  out_free:
1985         scsi_host_put(mesh_host);
1986  out_release:
1987         macio_release_resources(mdev);
1988 
1989         return -ENODEV;
1990 }
1991 
1992 static int mesh_remove(struct macio_dev *mdev)
1993 {
1994         struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1995         struct Scsi_Host *mesh_host = ms->host;
1996 
1997         scsi_remove_host(mesh_host);
1998 
1999         free_irq(ms->meshintr, ms);
2000 
2001         /* Reset scsi bus */
2002         mesh_shutdown(mdev);
2003 
2004         /* Shut down chip & termination */
2005         set_mesh_power(ms, 0);
2006 
2007         /* Unmap registers & dma controller */
2008         iounmap(ms->mesh);
2009         iounmap(ms->dma);
2010 
2011         /* Free DMA commands memory */
2012         dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size,
2013                             ms->dma_cmd_space, ms->dma_cmd_bus);
2014 
2015         /* Release memory resources */
2016         macio_release_resources(mdev);
2017 
2018         scsi_host_put(mesh_host);
2019 
2020         return 0;
2021 }
2022 
2023 
2024 static struct of_device_id mesh_match[] = 
2025 {
2026         {
2027         .name           = "mesh",
2028         },
2029         {
2030         .type           = "scsi",
2031         .compatible     = "chrp,mesh0"
2032         },
2033         {},
2034 };
2035 MODULE_DEVICE_TABLE (of, mesh_match);
2036 
2037 static struct macio_driver mesh_driver = 
2038 {
2039         .driver = {
2040                 .name           = "mesh",
2041                 .owner          = THIS_MODULE,
2042                 .of_match_table = mesh_match,
2043         },
2044         .probe          = mesh_probe,
2045         .remove         = mesh_remove,
2046         .shutdown       = mesh_shutdown,
2047 #ifdef CONFIG_PM
2048         .suspend        = mesh_suspend,
2049         .resume         = mesh_resume,
2050 #endif
2051 };
2052 
2053 
2054 static int __init init_mesh(void)
2055 {
2056 
2057         /* Calculate sync rate from module parameters */
2058         if (sync_rate > 10)
2059                 sync_rate = 10;
2060         if (sync_rate > 0) {
2061                 printk(KERN_INFO "mesh: configured for synchronous %d MB/s\n", sync_rate);
2062                 mesh_sync_period = 1000 / sync_rate;    /* ns */
2063                 mesh_sync_offset = 15;
2064         } else
2065                 printk(KERN_INFO "mesh: configured for asynchronous\n");
2066 
2067         return macio_register_driver(&mesh_driver);
2068 }
2069 
2070 static void __exit exit_mesh(void)
2071 {
2072         return macio_unregister_driver(&mesh_driver);
2073 }
2074 
2075 module_init(init_mesh);
2076 module_exit(exit_mesh);

/* [<][>][^][v][top][bottom][index][help] */