root/drivers/input/misc/keyspan_remote.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. keyspan_print
  2. keyspan_load_tester
  3. keyspan_report_button
  4. keyspan_check_data
  5. keyspan_setup
  6. keyspan_irq_recv
  7. keyspan_open
  8. keyspan_close
  9. keyspan_get_in_endpoint
  10. keyspan_probe
  11. keyspan_disconnect

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * keyspan_remote: USB driver for the Keyspan DMR
   4  *
   5  * Copyright (C) 2005 Zymeta Corporation - Michael Downey (downey@zymeta.com)
   6  *
   7  * This driver has been put together with the support of Innosys, Inc.
   8  * and Keyspan, Inc the manufacturers of the Keyspan USB DMR product.
   9  */
  10 
  11 #include <linux/kernel.h>
  12 #include <linux/errno.h>
  13 #include <linux/slab.h>
  14 #include <linux/module.h>
  15 #include <linux/usb/input.h>
  16 
  17 /* Parameters that can be passed to the driver. */
  18 static int debug;
  19 module_param(debug, int, 0444);
  20 MODULE_PARM_DESC(debug, "Enable extra debug messages and information");
  21 
  22 /* Vendor and product ids */
  23 #define USB_KEYSPAN_VENDOR_ID           0x06CD
  24 #define USB_KEYSPAN_PRODUCT_UIA11       0x0202
  25 
  26 /* Defines for converting the data from the remote. */
  27 #define ZERO            0x18
  28 #define ZERO_MASK       0x1F    /* 5 bits for a 0 */
  29 #define ONE             0x3C
  30 #define ONE_MASK        0x3F    /* 6 bits for a 1 */
  31 #define SYNC            0x3F80
  32 #define SYNC_MASK       0x3FFF  /* 14 bits for a SYNC sequence */
  33 #define STOP            0x00
  34 #define STOP_MASK       0x1F    /* 5 bits for the STOP sequence */
  35 #define GAP             0xFF
  36 
  37 #define RECV_SIZE       8       /* The UIA-11 type have a 8 byte limit. */
  38 
  39 /*
  40  * Table that maps the 31 possible keycodes to input keys.
  41  * Currently there are 15 and 17 button models so RESERVED codes
  42  * are blank areas in the mapping.
  43  */
  44 static const unsigned short keyspan_key_table[] = {
  45         KEY_RESERVED,           /* 0 is just a place holder. */
  46         KEY_RESERVED,
  47         KEY_STOP,
  48         KEY_PLAYCD,
  49         KEY_RESERVED,
  50         KEY_PREVIOUSSONG,
  51         KEY_REWIND,
  52         KEY_FORWARD,
  53         KEY_NEXTSONG,
  54         KEY_RESERVED,
  55         KEY_RESERVED,
  56         KEY_RESERVED,
  57         KEY_PAUSE,
  58         KEY_VOLUMEUP,
  59         KEY_RESERVED,
  60         KEY_RESERVED,
  61         KEY_RESERVED,
  62         KEY_VOLUMEDOWN,
  63         KEY_RESERVED,
  64         KEY_UP,
  65         KEY_RESERVED,
  66         KEY_MUTE,
  67         KEY_LEFT,
  68         KEY_ENTER,
  69         KEY_RIGHT,
  70         KEY_RESERVED,
  71         KEY_RESERVED,
  72         KEY_DOWN,
  73         KEY_RESERVED,
  74         KEY_KPASTERISK,
  75         KEY_RESERVED,
  76         KEY_MENU
  77 };
  78 
  79 /* table of devices that work with this driver */
  80 static const struct usb_device_id keyspan_table[] = {
  81         { USB_DEVICE(USB_KEYSPAN_VENDOR_ID, USB_KEYSPAN_PRODUCT_UIA11) },
  82         { }                                     /* Terminating entry */
  83 };
  84 
  85 /* Structure to store all the real stuff that a remote sends to us. */
  86 struct keyspan_message {
  87         u16     system;
  88         u8      button;
  89         u8      toggle;
  90 };
  91 
  92 /* Structure used for all the bit testing magic needed to be done. */
  93 struct bit_tester {
  94         u32     tester;
  95         int     len;
  96         int     pos;
  97         int     bits_left;
  98         u8      buffer[32];
  99 };
 100 
 101 /* Structure to hold all of our driver specific stuff */
 102 struct usb_keyspan {
 103         char                            name[128];
 104         char                            phys[64];
 105         unsigned short                  keymap[ARRAY_SIZE(keyspan_key_table)];
 106         struct usb_device               *udev;
 107         struct input_dev                *input;
 108         struct usb_interface            *interface;
 109         struct usb_endpoint_descriptor  *in_endpoint;
 110         struct urb*                     irq_urb;
 111         int                             open;
 112         dma_addr_t                      in_dma;
 113         unsigned char                   *in_buffer;
 114 
 115         /* variables used to parse messages from remote. */
 116         struct bit_tester               data;
 117         int                             stage;
 118         int                             toggle;
 119 };
 120 
 121 static struct usb_driver keyspan_driver;
 122 
 123 /*
 124  * Debug routine that prints out what we've received from the remote.
 125  */
 126 static void keyspan_print(struct usb_keyspan* dev) /*unsigned char* data)*/
 127 {
 128         char codes[4 * RECV_SIZE];
 129         int i;
 130 
 131         for (i = 0; i < RECV_SIZE; i++)
 132                 snprintf(codes + i * 3, 4, "%02x ", dev->in_buffer[i]);
 133 
 134         dev_info(&dev->udev->dev, "%s\n", codes);
 135 }
 136 
 137 /*
 138  * Routine that manages the bit_tester structure.  It makes sure that there are
 139  * at least bits_needed bits loaded into the tester.
 140  */
 141 static int keyspan_load_tester(struct usb_keyspan* dev, int bits_needed)
 142 {
 143         if (dev->data.bits_left >= bits_needed)
 144                 return 0;
 145 
 146         /*
 147          * Somehow we've missed the last message. The message will be repeated
 148          * though so it's not too big a deal
 149          */
 150         if (dev->data.pos >= dev->data.len) {
 151                 dev_dbg(&dev->interface->dev,
 152                         "%s - Error ran out of data. pos: %d, len: %d\n",
 153                         __func__, dev->data.pos, dev->data.len);
 154                 return -1;
 155         }
 156 
 157         /* Load as much as we can into the tester. */
 158         while ((dev->data.bits_left + 7 < (sizeof(dev->data.tester) * 8)) &&
 159                (dev->data.pos < dev->data.len)) {
 160                 dev->data.tester += (dev->data.buffer[dev->data.pos++] << dev->data.bits_left);
 161                 dev->data.bits_left += 8;
 162         }
 163 
 164         return 0;
 165 }
 166 
 167 static void keyspan_report_button(struct usb_keyspan *remote, int button, int press)
 168 {
 169         struct input_dev *input = remote->input;
 170 
 171         input_event(input, EV_MSC, MSC_SCAN, button);
 172         input_report_key(input, remote->keymap[button], press);
 173         input_sync(input);
 174 }
 175 
 176 /*
 177  * Routine that handles all the logic needed to parse out the message from the remote.
 178  */
 179 static void keyspan_check_data(struct usb_keyspan *remote)
 180 {
 181         int i;
 182         int found = 0;
 183         struct keyspan_message message;
 184 
 185         switch(remote->stage) {
 186         case 0:
 187                 /*
 188                  * In stage 0 we want to find the start of a message.  The remote sends a 0xFF as filler.
 189                  * So the first byte that isn't a FF should be the start of a new message.
 190                  */
 191                 for (i = 0; i < RECV_SIZE && remote->in_buffer[i] == GAP; ++i);
 192 
 193                 if (i < RECV_SIZE) {
 194                         memcpy(remote->data.buffer, remote->in_buffer, RECV_SIZE);
 195                         remote->data.len = RECV_SIZE;
 196                         remote->data.pos = 0;
 197                         remote->data.tester = 0;
 198                         remote->data.bits_left = 0;
 199                         remote->stage = 1;
 200                 }
 201                 break;
 202 
 203         case 1:
 204                 /*
 205                  * Stage 1 we should have 16 bytes and should be able to detect a
 206                  * SYNC.  The SYNC is 14 bits, 7 0's and then 7 1's.
 207                  */
 208                 memcpy(remote->data.buffer + remote->data.len, remote->in_buffer, RECV_SIZE);
 209                 remote->data.len += RECV_SIZE;
 210 
 211                 found = 0;
 212                 while ((remote->data.bits_left >= 14 || remote->data.pos < remote->data.len) && !found) {
 213                         for (i = 0; i < 8; ++i) {
 214                                 if (keyspan_load_tester(remote, 14) != 0) {
 215                                         remote->stage = 0;
 216                                         return;
 217                                 }
 218 
 219                                 if ((remote->data.tester & SYNC_MASK) == SYNC) {
 220                                         remote->data.tester = remote->data.tester >> 14;
 221                                         remote->data.bits_left -= 14;
 222                                         found = 1;
 223                                         break;
 224                                 } else {
 225                                         remote->data.tester = remote->data.tester >> 1;
 226                                         --remote->data.bits_left;
 227                                 }
 228                         }
 229                 }
 230 
 231                 if (!found) {
 232                         remote->stage = 0;
 233                         remote->data.len = 0;
 234                 } else {
 235                         remote->stage = 2;
 236                 }
 237                 break;
 238 
 239         case 2:
 240                 /*
 241                  * Stage 2 we should have 24 bytes which will be enough for a full
 242                  * message.  We need to parse out the system code, button code,
 243                  * toggle code, and stop.
 244                  */
 245                 memcpy(remote->data.buffer + remote->data.len, remote->in_buffer, RECV_SIZE);
 246                 remote->data.len += RECV_SIZE;
 247 
 248                 message.system = 0;
 249                 for (i = 0; i < 9; i++) {
 250                         keyspan_load_tester(remote, 6);
 251 
 252                         if ((remote->data.tester & ZERO_MASK) == ZERO) {
 253                                 message.system = message.system << 1;
 254                                 remote->data.tester = remote->data.tester >> 5;
 255                                 remote->data.bits_left -= 5;
 256                         } else if ((remote->data.tester & ONE_MASK) == ONE) {
 257                                 message.system = (message.system << 1) + 1;
 258                                 remote->data.tester = remote->data.tester >> 6;
 259                                 remote->data.bits_left -= 6;
 260                         } else {
 261                                 dev_err(&remote->interface->dev,
 262                                         "%s - Unknown sequence found in system data.\n",
 263                                         __func__);
 264                                 remote->stage = 0;
 265                                 return;
 266                         }
 267                 }
 268 
 269                 message.button = 0;
 270                 for (i = 0; i < 5; i++) {
 271                         keyspan_load_tester(remote, 6);
 272 
 273                         if ((remote->data.tester & ZERO_MASK) == ZERO) {
 274                                 message.button = message.button << 1;
 275                                 remote->data.tester = remote->data.tester >> 5;
 276                                 remote->data.bits_left -= 5;
 277                         } else if ((remote->data.tester & ONE_MASK) == ONE) {
 278                                 message.button = (message.button << 1) + 1;
 279                                 remote->data.tester = remote->data.tester >> 6;
 280                                 remote->data.bits_left -= 6;
 281                         } else {
 282                                 dev_err(&remote->interface->dev,
 283                                         "%s - Unknown sequence found in button data.\n",
 284                                         __func__);
 285                                 remote->stage = 0;
 286                                 return;
 287                         }
 288                 }
 289 
 290                 keyspan_load_tester(remote, 6);
 291                 if ((remote->data.tester & ZERO_MASK) == ZERO) {
 292                         message.toggle = 0;
 293                         remote->data.tester = remote->data.tester >> 5;
 294                         remote->data.bits_left -= 5;
 295                 } else if ((remote->data.tester & ONE_MASK) == ONE) {
 296                         message.toggle = 1;
 297                         remote->data.tester = remote->data.tester >> 6;
 298                         remote->data.bits_left -= 6;
 299                 } else {
 300                         dev_err(&remote->interface->dev,
 301                                 "%s - Error in message, invalid toggle.\n",
 302                                 __func__);
 303                         remote->stage = 0;
 304                         return;
 305                 }
 306 
 307                 keyspan_load_tester(remote, 5);
 308                 if ((remote->data.tester & STOP_MASK) == STOP) {
 309                         remote->data.tester = remote->data.tester >> 5;
 310                         remote->data.bits_left -= 5;
 311                 } else {
 312                         dev_err(&remote->interface->dev,
 313                                 "Bad message received, no stop bit found.\n");
 314                 }
 315 
 316                 dev_dbg(&remote->interface->dev,
 317                         "%s found valid message: system: %d, button: %d, toggle: %d\n",
 318                         __func__, message.system, message.button, message.toggle);
 319 
 320                 if (message.toggle != remote->toggle) {
 321                         keyspan_report_button(remote, message.button, 1);
 322                         keyspan_report_button(remote, message.button, 0);
 323                         remote->toggle = message.toggle;
 324                 }
 325 
 326                 remote->stage = 0;
 327                 break;
 328         }
 329 }
 330 
 331 /*
 332  * Routine for sending all the initialization messages to the remote.
 333  */
 334 static int keyspan_setup(struct usb_device* dev)
 335 {
 336         int retval = 0;
 337 
 338         retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 339                                  0x11, 0x40, 0x5601, 0x0, NULL, 0,
 340                                  USB_CTRL_SET_TIMEOUT);
 341         if (retval) {
 342                 dev_dbg(&dev->dev, "%s - failed to set bit rate due to error: %d\n",
 343                         __func__, retval);
 344                 return(retval);
 345         }
 346 
 347         retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 348                                  0x44, 0x40, 0x0, 0x0, NULL, 0,
 349                                  USB_CTRL_SET_TIMEOUT);
 350         if (retval) {
 351                 dev_dbg(&dev->dev, "%s - failed to set resume sensitivity due to error: %d\n",
 352                         __func__, retval);
 353                 return(retval);
 354         }
 355 
 356         retval = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 357                                  0x22, 0x40, 0x0, 0x0, NULL, 0,
 358                                  USB_CTRL_SET_TIMEOUT);
 359         if (retval) {
 360                 dev_dbg(&dev->dev, "%s - failed to turn receive on due to error: %d\n",
 361                         __func__, retval);
 362                 return(retval);
 363         }
 364 
 365         dev_dbg(&dev->dev, "%s - Setup complete.\n", __func__);
 366         return(retval);
 367 }
 368 
 369 /*
 370  * Routine used to handle a new message that has come in.
 371  */
 372 static void keyspan_irq_recv(struct urb *urb)
 373 {
 374         struct usb_keyspan *dev = urb->context;
 375         int retval;
 376 
 377         /* Check our status in case we need to bail out early. */
 378         switch (urb->status) {
 379         case 0:
 380                 break;
 381 
 382         /* Device went away so don't keep trying to read from it. */
 383         case -ECONNRESET:
 384         case -ENOENT:
 385         case -ESHUTDOWN:
 386                 return;
 387 
 388         default:
 389                 goto resubmit;
 390         }
 391 
 392         if (debug)
 393                 keyspan_print(dev);
 394 
 395         keyspan_check_data(dev);
 396 
 397 resubmit:
 398         retval = usb_submit_urb(urb, GFP_ATOMIC);
 399         if (retval)
 400                 dev_err(&dev->interface->dev,
 401                         "%s - usb_submit_urb failed with result: %d\n",
 402                         __func__, retval);
 403 }
 404 
 405 static int keyspan_open(struct input_dev *dev)
 406 {
 407         struct usb_keyspan *remote = input_get_drvdata(dev);
 408 
 409         remote->irq_urb->dev = remote->udev;
 410         if (usb_submit_urb(remote->irq_urb, GFP_KERNEL))
 411                 return -EIO;
 412 
 413         return 0;
 414 }
 415 
 416 static void keyspan_close(struct input_dev *dev)
 417 {
 418         struct usb_keyspan *remote = input_get_drvdata(dev);
 419 
 420         usb_kill_urb(remote->irq_urb);
 421 }
 422 
 423 static struct usb_endpoint_descriptor *keyspan_get_in_endpoint(struct usb_host_interface *iface)
 424 {
 425 
 426         struct usb_endpoint_descriptor *endpoint;
 427         int i;
 428 
 429         for (i = 0; i < iface->desc.bNumEndpoints; ++i) {
 430                 endpoint = &iface->endpoint[i].desc;
 431 
 432                 if (usb_endpoint_is_int_in(endpoint)) {
 433                         /* we found our interrupt in endpoint */
 434                         return endpoint;
 435                 }
 436         }
 437 
 438         return NULL;
 439 }
 440 
 441 /*
 442  * Routine that sets up the driver to handle a specific USB device detected on the bus.
 443  */
 444 static int keyspan_probe(struct usb_interface *interface, const struct usb_device_id *id)
 445 {
 446         struct usb_device *udev = interface_to_usbdev(interface);
 447         struct usb_endpoint_descriptor *endpoint;
 448         struct usb_keyspan *remote;
 449         struct input_dev *input_dev;
 450         int i, error;
 451 
 452         endpoint = keyspan_get_in_endpoint(interface->cur_altsetting);
 453         if (!endpoint)
 454                 return -ENODEV;
 455 
 456         remote = kzalloc(sizeof(*remote), GFP_KERNEL);
 457         input_dev = input_allocate_device();
 458         if (!remote || !input_dev) {
 459                 error = -ENOMEM;
 460                 goto fail1;
 461         }
 462 
 463         remote->udev = udev;
 464         remote->input = input_dev;
 465         remote->interface = interface;
 466         remote->in_endpoint = endpoint;
 467         remote->toggle = -1;    /* Set to -1 so we will always not match the toggle from the first remote message. */
 468 
 469         remote->in_buffer = usb_alloc_coherent(udev, RECV_SIZE, GFP_KERNEL, &remote->in_dma);
 470         if (!remote->in_buffer) {
 471                 error = -ENOMEM;
 472                 goto fail1;
 473         }
 474 
 475         remote->irq_urb = usb_alloc_urb(0, GFP_KERNEL);
 476         if (!remote->irq_urb) {
 477                 error = -ENOMEM;
 478                 goto fail2;
 479         }
 480 
 481         error = keyspan_setup(udev);
 482         if (error) {
 483                 error = -ENODEV;
 484                 goto fail3;
 485         }
 486 
 487         if (udev->manufacturer)
 488                 strlcpy(remote->name, udev->manufacturer, sizeof(remote->name));
 489 
 490         if (udev->product) {
 491                 if (udev->manufacturer)
 492                         strlcat(remote->name, " ", sizeof(remote->name));
 493                 strlcat(remote->name, udev->product, sizeof(remote->name));
 494         }
 495 
 496         if (!strlen(remote->name))
 497                 snprintf(remote->name, sizeof(remote->name),
 498                          "USB Keyspan Remote %04x:%04x",
 499                          le16_to_cpu(udev->descriptor.idVendor),
 500                          le16_to_cpu(udev->descriptor.idProduct));
 501 
 502         usb_make_path(udev, remote->phys, sizeof(remote->phys));
 503         strlcat(remote->phys, "/input0", sizeof(remote->phys));
 504         memcpy(remote->keymap, keyspan_key_table, sizeof(remote->keymap));
 505 
 506         input_dev->name = remote->name;
 507         input_dev->phys = remote->phys;
 508         usb_to_input_id(udev, &input_dev->id);
 509         input_dev->dev.parent = &interface->dev;
 510         input_dev->keycode = remote->keymap;
 511         input_dev->keycodesize = sizeof(unsigned short);
 512         input_dev->keycodemax = ARRAY_SIZE(remote->keymap);
 513 
 514         input_set_capability(input_dev, EV_MSC, MSC_SCAN);
 515         __set_bit(EV_KEY, input_dev->evbit);
 516         for (i = 0; i < ARRAY_SIZE(keyspan_key_table); i++)
 517                 __set_bit(keyspan_key_table[i], input_dev->keybit);
 518         __clear_bit(KEY_RESERVED, input_dev->keybit);
 519 
 520         input_set_drvdata(input_dev, remote);
 521 
 522         input_dev->open = keyspan_open;
 523         input_dev->close = keyspan_close;
 524 
 525         /*
 526          * Initialize the URB to access the device.
 527          * The urb gets sent to the device in keyspan_open()
 528          */
 529         usb_fill_int_urb(remote->irq_urb,
 530                          remote->udev,
 531                          usb_rcvintpipe(remote->udev, endpoint->bEndpointAddress),
 532                          remote->in_buffer, RECV_SIZE, keyspan_irq_recv, remote,
 533                          endpoint->bInterval);
 534         remote->irq_urb->transfer_dma = remote->in_dma;
 535         remote->irq_urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
 536 
 537         /* we can register the device now, as it is ready */
 538         error = input_register_device(remote->input);
 539         if (error)
 540                 goto fail3;
 541 
 542         /* save our data pointer in this interface device */
 543         usb_set_intfdata(interface, remote);
 544 
 545         return 0;
 546 
 547  fail3: usb_free_urb(remote->irq_urb);
 548  fail2: usb_free_coherent(udev, RECV_SIZE, remote->in_buffer, remote->in_dma);
 549  fail1: kfree(remote);
 550         input_free_device(input_dev);
 551 
 552         return error;
 553 }
 554 
 555 /*
 556  * Routine called when a device is disconnected from the USB.
 557  */
 558 static void keyspan_disconnect(struct usb_interface *interface)
 559 {
 560         struct usb_keyspan *remote;
 561 
 562         remote = usb_get_intfdata(interface);
 563         usb_set_intfdata(interface, NULL);
 564 
 565         if (remote) {   /* We have a valid driver structure so clean up everything we allocated. */
 566                 input_unregister_device(remote->input);
 567                 usb_kill_urb(remote->irq_urb);
 568                 usb_free_urb(remote->irq_urb);
 569                 usb_free_coherent(remote->udev, RECV_SIZE, remote->in_buffer, remote->in_dma);
 570                 kfree(remote);
 571         }
 572 }
 573 
 574 /*
 575  * Standard driver set up sections
 576  */
 577 static struct usb_driver keyspan_driver =
 578 {
 579         .name =         "keyspan_remote",
 580         .probe =        keyspan_probe,
 581         .disconnect =   keyspan_disconnect,
 582         .id_table =     keyspan_table
 583 };
 584 
 585 module_usb_driver(keyspan_driver);
 586 
 587 MODULE_DEVICE_TABLE(usb, keyspan_table);
 588 MODULE_AUTHOR("Michael Downey <downey@zymeta.com>");
 589 MODULE_DESCRIPTION("Driver for the USB Keyspan remote control.");
 590 MODULE_LICENSE("GPL");

/* [<][>][^][v][top][bottom][index][help] */