drivers/rtc/rtc-pcf2123.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
pcf2123_read_offset
pcf2123_set_offset
pcf2123_rtc_read_time
pcf2123_rtc_set_time
pcf2123_rtc_alarm_irq_enable
pcf2123_rtc_read_alarm
pcf2123_rtc_set_alarm
pcf2123_rtc_irq
pcf2123_reset
pcf2123_probe
   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * An SPI driver for the Philips PCF2123 RTC
   4  * Copyright 2009 Cyber Switching, Inc.
   5  *
   6  * Author: Chris Verges <chrisv@cyberswitching.com>
   7  * Maintainers: http://www.cyberswitching.com
   8  *
   9  * based on the RS5C348 driver in this same directory.
  10  *
  11  * Thanks to Christian Pellegrin <chripell@fsfe.org> for
  12  * the sysfs contributions to this driver.
  13  *
  14  * Please note that the CS is active high, so platform data
  15  * should look something like:
  16  *
  17  * static struct spi_board_info ek_spi_devices[] = {
  18  *      ...
  19  *      {
  20  *              .modalias               = "rtc-pcf2123",
  21  *              .chip_select            = 1,
  22  *              .controller_data        = (void *)AT91_PIN_PA10,
  23  *              .max_speed_hz           = 1000 * 1000,
  24  *              .mode                   = SPI_CS_HIGH,
  25  *              .bus_num                = 0,
  26  *      },
  27  *      ...
  28  *};
  29  */
  30 
  31 #include <linux/bcd.h>
  32 #include <linux/delay.h>
  33 #include <linux/device.h>
  34 #include <linux/errno.h>
  35 #include <linux/init.h>
  36 #include <linux/kernel.h>
  37 #include <linux/of.h>
  38 #include <linux/string.h>
  39 #include <linux/slab.h>
  40 #include <linux/rtc.h>
  41 #include <linux/spi/spi.h>
  42 #include <linux/module.h>
  43 #include <linux/regmap.h>
  44 
  45 /* REGISTERS */
  46 #define PCF2123_REG_CTRL1       (0x00)  /* Control Register 1 */
  47 #define PCF2123_REG_CTRL2       (0x01)  /* Control Register 2 */
  48 #define PCF2123_REG_SC          (0x02)  /* datetime */
  49 #define PCF2123_REG_MN          (0x03)
  50 #define PCF2123_REG_HR          (0x04)
  51 #define PCF2123_REG_DM          (0x05)
  52 #define PCF2123_REG_DW          (0x06)
  53 #define PCF2123_REG_MO          (0x07)
  54 #define PCF2123_REG_YR          (0x08)
  55 #define PCF2123_REG_ALRM_MN     (0x09)  /* Alarm Registers */
  56 #define PCF2123_REG_ALRM_HR     (0x0a)
  57 #define PCF2123_REG_ALRM_DM     (0x0b)
  58 #define PCF2123_REG_ALRM_DW     (0x0c)
  59 #define PCF2123_REG_OFFSET      (0x0d)  /* Clock Rate Offset Register */
  60 #define PCF2123_REG_TMR_CLKOUT  (0x0e)  /* Timer Registers */
  61 #define PCF2123_REG_CTDWN_TMR   (0x0f)
  62 
  63 /* PCF2123_REG_CTRL1 BITS */
  64 #define CTRL1_CLEAR             (0)     /* Clear */
  65 #define CTRL1_CORR_INT          BIT(1)  /* Correction irq enable */
  66 #define CTRL1_12_HOUR           BIT(2)  /* 12 hour time */
  67 #define CTRL1_SW_RESET  (BIT(3) | BIT(4) | BIT(6))      /* Software reset */
  68 #define CTRL1_STOP              BIT(5)  /* Stop the clock */
  69 #define CTRL1_EXT_TEST          BIT(7)  /* External clock test mode */
  70 
  71 /* PCF2123_REG_CTRL2 BITS */
  72 #define CTRL2_TIE               BIT(0)  /* Countdown timer irq enable */
  73 #define CTRL2_AIE               BIT(1)  /* Alarm irq enable */
  74 #define CTRL2_TF                BIT(2)  /* Countdown timer flag */
  75 #define CTRL2_AF                BIT(3)  /* Alarm flag */
  76 #define CTRL2_TI_TP             BIT(4)  /* Irq pin generates pulse */
  77 #define CTRL2_MSF               BIT(5)  /* Minute or second irq flag */
  78 #define CTRL2_SI                BIT(6)  /* Second irq enable */
  79 #define CTRL2_MI                BIT(7)  /* Minute irq enable */
  80 
  81 /* PCF2123_REG_SC BITS */
  82 #define OSC_HAS_STOPPED         BIT(7)  /* Clock has been stopped */
  83 
  84 /* PCF2123_REG_ALRM_XX BITS */
  85 #define ALRM_DISABLE            BIT(7)  /* MN, HR, DM, or DW alarm matching */
  86 
  87 /* PCF2123_REG_TMR_CLKOUT BITS */
  88 #define CD_TMR_4096KHZ          (0)     /* 4096 KHz countdown timer */
  89 #define CD_TMR_64HZ             (1)     /* 64 Hz countdown timer */
  90 #define CD_TMR_1HZ              (2)     /* 1 Hz countdown timer */
  91 #define CD_TMR_60th_HZ          (3)     /* 60th Hz countdown timer */
  92 #define CD_TMR_TE               BIT(3)  /* Countdown timer enable */
  93 
  94 /* PCF2123_REG_OFFSET BITS */
  95 #define OFFSET_SIGN_BIT         6       /* 2's complement sign bit */
  96 #define OFFSET_COARSE           BIT(7)  /* Coarse mode offset */
  97 #define OFFSET_STEP             (2170)  /* Offset step in parts per billion */
  98 #define OFFSET_MASK             GENMASK(6, 0)   /* Offset value */
  99 
 100 /* READ/WRITE ADDRESS BITS */
 101 #define PCF2123_WRITE           BIT(4)
 102 #define PCF2123_READ            (BIT(4) | BIT(7))
 103 
 104 
 105 static struct spi_driver pcf2123_driver;
 106 
 107 struct pcf2123_data {
 108         struct rtc_device *rtc;
 109         struct regmap *map;
 110 };
 111 
 112 static const struct regmap_config pcf2123_regmap_config = {
 113         .reg_bits = 8,
 114         .val_bits = 8,
 115         .read_flag_mask = PCF2123_READ,
 116         .write_flag_mask = PCF2123_WRITE,
 117         .max_register = PCF2123_REG_CTDWN_TMR,
 118 };
 119 
 120 static int pcf2123_read_offset(struct device *dev, long *offset)
 121 {
 122         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 123         int ret, val;
 124         unsigned int reg;
 125 
 126         ret = regmap_read(pcf2123->map, PCF2123_REG_OFFSET, &reg);
 127         if (ret)
 128                 return ret;
 129 
 130         val = sign_extend32((reg & OFFSET_MASK), OFFSET_SIGN_BIT);
 131 
 132         if (reg & OFFSET_COARSE)
 133                 val *= 2;
 134 
 135         *offset = ((long)val) * OFFSET_STEP;
 136 
 137         return 0;
 138 }
 139 
 140 /*
 141  * The offset register is a 7 bit signed value with a coarse bit in bit 7.
 142  * The main difference between the two is normal offset adjusts the first
 143  * second of n minutes every other hour, with 61, 62 and 63 being shoved
 144  * into the 60th minute.
 145  * The coarse adjustment does the same, but every hour.
 146  * the two overlap, with every even normal offset value corresponding
 147  * to a coarse offset. Based on this algorithm, it seems that despite the
 148  * name, coarse offset is a better fit for overlapping values.
 149  */
 150 static int pcf2123_set_offset(struct device *dev, long offset)
 151 {
 152         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 153         s8 reg;
 154 
 155         if (offset > OFFSET_STEP * 127)
 156                 reg = 127;
 157         else if (offset < OFFSET_STEP * -128)
 158                 reg = -128;
 159         else
 160                 reg = DIV_ROUND_CLOSEST(offset, OFFSET_STEP);
 161 
 162         /* choose fine offset only for odd values in the normal range */
 163         if (reg & 1 && reg <= 63 && reg >= -64) {
 164                 /* Normal offset. Clear the coarse bit */
 165                 reg &= ~OFFSET_COARSE;
 166         } else {
 167                 /* Coarse offset. Divide by 2 and set the coarse bit */
 168                 reg >>= 1;
 169                 reg |= OFFSET_COARSE;
 170         }
 171 
 172         return regmap_write(pcf2123->map, PCF2123_REG_OFFSET, (unsigned int)reg);
 173 }
 174 
 175 static int pcf2123_rtc_read_time(struct device *dev, struct rtc_time *tm)
 176 {
 177         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 178         u8 rxbuf[7];
 179         int ret;
 180 
 181         ret = regmap_bulk_read(pcf2123->map, PCF2123_REG_SC, rxbuf,
 182                                 sizeof(rxbuf));
 183         if (ret)
 184                 return ret;
 185 
 186         if (rxbuf[0] & OSC_HAS_STOPPED) {
 187                 dev_info(dev, "clock was stopped. Time is not valid\n");
 188                 return -EINVAL;
 189         }
 190 
 191         tm->tm_sec = bcd2bin(rxbuf[0] & 0x7F);
 192         tm->tm_min = bcd2bin(rxbuf[1] & 0x7F);
 193         tm->tm_hour = bcd2bin(rxbuf[2] & 0x3F); /* rtc hr 0-23 */
 194         tm->tm_mday = bcd2bin(rxbuf[3] & 0x3F);
 195         tm->tm_wday = rxbuf[4] & 0x07;
 196         tm->tm_mon = bcd2bin(rxbuf[5] & 0x1F) - 1; /* rtc mn 1-12 */
 197         tm->tm_year = bcd2bin(rxbuf[6]) + 100;
 198 
 199         dev_dbg(dev, "%s: tm is %ptR\n", __func__, tm);
 200 
 201         return 0;
 202 }
 203 
 204 static int pcf2123_rtc_set_time(struct device *dev, struct rtc_time *tm)
 205 {
 206         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 207         u8 txbuf[7];
 208         int ret;
 209 
 210         dev_dbg(dev, "%s: tm is %ptR\n", __func__, tm);
 211 
 212         /* Stop the counter first */
 213         ret = regmap_write(pcf2123->map, PCF2123_REG_CTRL1, CTRL1_STOP);
 214         if (ret)
 215                 return ret;
 216 
 217         /* Set the new time */
 218         txbuf[0] = bin2bcd(tm->tm_sec & 0x7F);
 219         txbuf[1] = bin2bcd(tm->tm_min & 0x7F);
 220         txbuf[2] = bin2bcd(tm->tm_hour & 0x3F);
 221         txbuf[3] = bin2bcd(tm->tm_mday & 0x3F);
 222         txbuf[4] = tm->tm_wday & 0x07;
 223         txbuf[5] = bin2bcd((tm->tm_mon + 1) & 0x1F); /* rtc mn 1-12 */
 224         txbuf[6] = bin2bcd(tm->tm_year - 100);
 225 
 226         ret = regmap_bulk_write(pcf2123->map, PCF2123_REG_SC, txbuf,
 227                                 sizeof(txbuf));
 228         if (ret)
 229                 return ret;
 230 
 231         /* Start the counter */
 232         ret = regmap_write(pcf2123->map, PCF2123_REG_CTRL1, CTRL1_CLEAR);
 233         if (ret)
 234                 return ret;
 235 
 236         return 0;
 237 }
 238 
 239 static int pcf2123_rtc_alarm_irq_enable(struct device *dev, unsigned int en)
 240 {
 241         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 242 
 243         return regmap_update_bits(pcf2123->map, PCF2123_REG_CTRL2, CTRL2_AIE,
 244                                   en ? CTRL2_AIE : 0);
 245 }
 246 
 247 static int pcf2123_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm)
 248 {
 249         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 250         u8 rxbuf[4];
 251         int ret;
 252         unsigned int val = 0;
 253 
 254         ret = regmap_bulk_read(pcf2123->map, PCF2123_REG_ALRM_MN, rxbuf,
 255                                 sizeof(rxbuf));
 256         if (ret)
 257                 return ret;
 258 
 259         alm->time.tm_min = bcd2bin(rxbuf[0] & 0x7F);
 260         alm->time.tm_hour = bcd2bin(rxbuf[1] & 0x3F);
 261         alm->time.tm_mday = bcd2bin(rxbuf[2] & 0x3F);
 262         alm->time.tm_wday = bcd2bin(rxbuf[3] & 0x07);
 263 
 264         dev_dbg(dev, "%s: alm is %ptR\n", __func__, &alm->time);
 265 
 266         ret = regmap_read(pcf2123->map, PCF2123_REG_CTRL2, &val);
 267         if (ret)
 268                 return ret;
 269 
 270         alm->enabled = !!(val & CTRL2_AIE);
 271 
 272         return 0;
 273 }
 274 
 275 static int pcf2123_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm)
 276 {
 277         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 278         u8 txbuf[4];
 279         int ret;
 280 
 281         dev_dbg(dev, "%s: alm is %ptR\n", __func__, &alm->time);
 282 
 283         /* Disable alarm interrupt */
 284         ret = regmap_update_bits(pcf2123->map, PCF2123_REG_CTRL2, CTRL2_AIE, 0);
 285         if (ret)
 286                 return ret;
 287 
 288         /* Ensure alarm flag is clear */
 289         ret = regmap_update_bits(pcf2123->map, PCF2123_REG_CTRL2, CTRL2_AF, 0);
 290         if (ret)
 291                 return ret;
 292 
 293         /* Set new alarm */
 294         txbuf[0] = bin2bcd(alm->time.tm_min & 0x7F);
 295         txbuf[1] = bin2bcd(alm->time.tm_hour & 0x3F);
 296         txbuf[2] = bin2bcd(alm->time.tm_mday & 0x3F);
 297         txbuf[3] = ALRM_DISABLE;
 298 
 299         ret = regmap_bulk_write(pcf2123->map, PCF2123_REG_ALRM_MN, txbuf,
 300                                 sizeof(txbuf));
 301         if (ret)
 302                 return ret;
 303 
 304         return pcf2123_rtc_alarm_irq_enable(dev, alm->enabled);
 305 }
 306 
 307 static irqreturn_t pcf2123_rtc_irq(int irq, void *dev)
 308 {
 309         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 310         struct mutex *lock = &pcf2123->rtc->ops_lock;
 311         unsigned int val = 0;
 312         int ret = IRQ_NONE;
 313 
 314         mutex_lock(lock);
 315         regmap_read(pcf2123->map, PCF2123_REG_CTRL2, &val);
 316 
 317         /* Alarm? */
 318         if (val & CTRL2_AF) {
 319                 ret = IRQ_HANDLED;
 320 
 321                 /* Clear alarm flag */
 322                 regmap_update_bits(pcf2123->map, PCF2123_REG_CTRL2, CTRL2_AF, 0);
 323 
 324                 rtc_update_irq(pcf2123->rtc, 1, RTC_IRQF | RTC_AF);
 325         }
 326 
 327         mutex_unlock(lock);
 328 
 329         return ret;
 330 }
 331 
 332 static int pcf2123_reset(struct device *dev)
 333 {
 334         struct pcf2123_data *pcf2123 = dev_get_drvdata(dev);
 335         int ret;
 336         unsigned int val = 0;
 337 
 338         ret = regmap_write(pcf2123->map, PCF2123_REG_CTRL1, CTRL1_SW_RESET);
 339         if (ret)
 340                 return ret;
 341 
 342         /* Stop the counter */
 343         dev_dbg(dev, "stopping RTC\n");
 344         ret = regmap_write(pcf2123->map, PCF2123_REG_CTRL1, CTRL1_STOP);
 345         if (ret)
 346                 return ret;
 347 
 348         /* See if the counter was actually stopped */
 349         dev_dbg(dev, "checking for presence of RTC\n");
 350         ret = regmap_read(pcf2123->map, PCF2123_REG_CTRL1, &val);
 351         if (ret)
 352                 return ret;
 353 
 354         dev_dbg(dev, "received data from RTC (0x%08X)\n", val);
 355         if (!(val & CTRL1_STOP))
 356                 return -ENODEV;
 357 
 358         /* Start the counter */
 359         ret = regmap_write(pcf2123->map, PCF2123_REG_CTRL1, CTRL1_CLEAR);
 360         if (ret)
 361                 return ret;
 362 
 363         return 0;
 364 }
 365 
 366 static const struct rtc_class_ops pcf2123_rtc_ops = {
 367         .read_time      = pcf2123_rtc_read_time,
 368         .set_time       = pcf2123_rtc_set_time,
 369         .read_offset    = pcf2123_read_offset,
 370         .set_offset     = pcf2123_set_offset,
 371         .read_alarm     = pcf2123_rtc_read_alarm,
 372         .set_alarm      = pcf2123_rtc_set_alarm,
 373         .alarm_irq_enable = pcf2123_rtc_alarm_irq_enable,
 374 };
 375 
 376 static int pcf2123_probe(struct spi_device *spi)
 377 {
 378         struct rtc_device *rtc;
 379         struct rtc_time tm;
 380         struct pcf2123_data *pcf2123;
 381         int ret = 0;
 382 
 383         pcf2123 = devm_kzalloc(&spi->dev, sizeof(struct pcf2123_data),
 384                                 GFP_KERNEL);
 385         if (!pcf2123)
 386                 return -ENOMEM;
 387 
 388         dev_set_drvdata(&spi->dev, pcf2123);
 389 
 390         pcf2123->map = devm_regmap_init_spi(spi, &pcf2123_regmap_config);
 391         if (IS_ERR(pcf2123->map)) {
 392                 dev_err(&spi->dev, "regmap init failed.\n");
 393                 return PTR_ERR(pcf2123->map);
 394         }
 395 
 396         ret = pcf2123_rtc_read_time(&spi->dev, &tm);
 397         if (ret < 0) {
 398                 ret = pcf2123_reset(&spi->dev);
 399                 if (ret < 0) {
 400                         dev_err(&spi->dev, "chip not found\n");
 401                         return ret;
 402                 }
 403         }
 404 
 405         dev_info(&spi->dev, "spiclk %u KHz.\n",
 406                         (spi->max_speed_hz + 500) / 1000);
 407 
 408         /* Finalize the initialization */
 409         rtc = devm_rtc_allocate_device(&spi->dev);
 410         if (IS_ERR(rtc))
 411                 return PTR_ERR(rtc);
 412 
 413         pcf2123->rtc = rtc;
 414 
 415         /* Register alarm irq */
 416         if (spi->irq > 0) {
 417                 ret = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
 418                                 pcf2123_rtc_irq,
 419                                 IRQF_TRIGGER_LOW | IRQF_ONESHOT,
 420                                 pcf2123_driver.driver.name, &spi->dev);
 421                 if (!ret)
 422                         device_init_wakeup(&spi->dev, true);
 423                 else
 424                         dev_err(&spi->dev, "could not request irq.\n");
 425         }
 426 
 427         /* The PCF2123's alarm only has minute accuracy. Must add timer
 428          * support to this driver to generate interrupts more than once
 429          * per minute.
 430          */
 431         rtc->uie_unsupported = 1;
 432         rtc->ops = &pcf2123_rtc_ops;
 433         rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 434         rtc->range_max = RTC_TIMESTAMP_END_2099;
 435         rtc->set_start_time = true;
 436 
 437         ret = rtc_register_device(rtc);
 438         if (ret)
 439                 return ret;
 440 
 441         return 0;
 442 }
 443 
 444 #ifdef CONFIG_OF
 445 static const struct of_device_id pcf2123_dt_ids[] = {
 446         { .compatible = "nxp,pcf2123", },
 447         { .compatible = "microcrystal,rv2123", },
 448         /* Deprecated, do not use */
 449         { .compatible = "nxp,rtc-pcf2123", },
 450         { /* sentinel */ }
 451 };
 452 MODULE_DEVICE_TABLE(of, pcf2123_dt_ids);
 453 #endif
 454 
 455 static struct spi_driver pcf2123_driver = {
 456         .driver = {
 457                         .name   = "rtc-pcf2123",
 458                         .of_match_table = of_match_ptr(pcf2123_dt_ids),
 459         },
 460         .probe  = pcf2123_probe,
 461 };
 462 
 463 module_spi_driver(pcf2123_driver);
 464 
 465 MODULE_AUTHOR("Chris Verges <chrisv@cyberswitching.com>");
 466 MODULE_DESCRIPTION("NXP PCF2123 RTC driver");
 467 MODULE_LICENSE("GPL");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/rtc/rtc-pcf2123.c

DEFINITIONS
