drivers/rapidio/switches/idt

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
idtg2_route_add_entry
idtg2_route_get_entry
idtg2_route_clr_table
idtg2_set_domain
idtg2_get_domain
idtg2_em_init
idtg2_em_handler
idtg2_show_errlog
idtg2_sysfs
idtg2_probe
idtg2_remove
idtg2_init
idtg2_exit
   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * IDT CPS Gen.2 Serial RapidIO switch family support
   4  *
   5  * Copyright 2010 Integrated Device Technology, Inc.
   6  * Alexandre Bounine <alexandre.bounine@idt.com>
   7  */
   8 
   9 #include <linux/stat.h>
  10 #include <linux/module.h>
  11 #include <linux/rio.h>
  12 #include <linux/rio_drv.h>
  13 #include <linux/rio_ids.h>
  14 #include <linux/delay.h>
  15 
  16 #include <asm/page.h>
  17 #include "../rio.h"
  18 
  19 #define LOCAL_RTE_CONF_DESTID_SEL       0x010070
  20 #define LOCAL_RTE_CONF_DESTID_SEL_PSEL  0x0000001f
  21 
  22 #define IDT_LT_ERR_REPORT_EN    0x03100c
  23 
  24 #define IDT_PORT_ERR_REPORT_EN(n)       (0x031044 + (n)*0x40)
  25 #define IDT_PORT_ERR_REPORT_EN_BC       0x03ff04
  26 
  27 #define IDT_PORT_ISERR_REPORT_EN(n)     (0x03104C + (n)*0x40)
  28 #define IDT_PORT_ISERR_REPORT_EN_BC     0x03ff0c
  29 #define IDT_PORT_INIT_TX_ACQUIRED       0x00000020
  30 
  31 #define IDT_LANE_ERR_REPORT_EN(n)       (0x038010 + (n)*0x100)
  32 #define IDT_LANE_ERR_REPORT_EN_BC       0x03ff10
  33 
  34 #define IDT_DEV_CTRL_1          0xf2000c
  35 #define IDT_DEV_CTRL_1_GENPW            0x02000000
  36 #define IDT_DEV_CTRL_1_PRSTBEH          0x00000001
  37 
  38 #define IDT_CFGBLK_ERR_CAPTURE_EN       0x020008
  39 #define IDT_CFGBLK_ERR_REPORT           0xf20014
  40 #define IDT_CFGBLK_ERR_REPORT_GENPW             0x00000002
  41 
  42 #define IDT_AUX_PORT_ERR_CAP_EN 0x020000
  43 #define IDT_AUX_ERR_REPORT_EN   0xf20018
  44 #define IDT_AUX_PORT_ERR_LOG_I2C        0x00000002
  45 #define IDT_AUX_PORT_ERR_LOG_JTAG       0x00000001
  46 
  47 #define IDT_ISLTL_ADDRESS_CAP   0x021014
  48 
  49 #define IDT_RIO_DOMAIN          0xf20020
  50 #define IDT_RIO_DOMAIN_MASK             0x000000ff
  51 
  52 #define IDT_PW_INFO_CSR         0xf20024
  53 
  54 #define IDT_SOFT_RESET          0xf20040
  55 #define IDT_SOFT_RESET_REQ              0x00030097
  56 
  57 #define IDT_I2C_MCTRL           0xf20050
  58 #define IDT_I2C_MCTRL_GENPW             0x04000000
  59 
  60 #define IDT_JTAG_CTRL           0xf2005c
  61 #define IDT_JTAG_CTRL_GENPW             0x00000002
  62 
  63 #define IDT_LANE_CTRL(n)        (0xff8000 + (n)*0x100)
  64 #define IDT_LANE_CTRL_BC        0xffff00
  65 #define IDT_LANE_CTRL_GENPW             0x00200000
  66 #define IDT_LANE_DFE_1_BC       0xffff18
  67 #define IDT_LANE_DFE_2_BC       0xffff1c
  68 
  69 #define IDT_PORT_OPS(n)         (0xf40004 + (n)*0x100)
  70 #define IDT_PORT_OPS_GENPW              0x08000000
  71 #define IDT_PORT_OPS_PL_ELOG            0x00000040
  72 #define IDT_PORT_OPS_LL_ELOG            0x00000020
  73 #define IDT_PORT_OPS_LT_ELOG            0x00000010
  74 #define IDT_PORT_OPS_BC         0xf4ff04
  75 
  76 #define IDT_PORT_ISERR_DET(n)   (0xf40008 + (n)*0x100)
  77 
  78 #define IDT_ERR_CAP             0xfd0000
  79 #define IDT_ERR_CAP_LOG_OVERWR          0x00000004
  80 
  81 #define IDT_ERR_RD              0xfd0004
  82 
  83 #define IDT_DEFAULT_ROUTE       0xde
  84 #define IDT_NO_ROUTE            0xdf
  85 
  86 static int
  87 idtg2_route_add_entry(struct rio_mport *mport, u16 destid, u8 hopcount,
  88                        u16 table, u16 route_destid, u8 route_port)
  89 {
  90         /*
  91          * Select routing table to update
  92          */
  93         if (table == RIO_GLOBAL_TABLE)
  94                 table = 0;
  95         else
  96                 table++;
  97 
  98         if (route_port == RIO_INVALID_ROUTE)
  99                 route_port = IDT_DEFAULT_ROUTE;
 100 
 101         rio_mport_write_config_32(mport, destid, hopcount,
 102                                   LOCAL_RTE_CONF_DESTID_SEL, table);
 103 
 104         /*
 105          * Program destination port for the specified destID
 106          */
 107         rio_mport_write_config_32(mport, destid, hopcount,
 108                                   RIO_STD_RTE_CONF_DESTID_SEL_CSR,
 109                                   (u32)route_destid);
 110 
 111         rio_mport_write_config_32(mport, destid, hopcount,
 112                                   RIO_STD_RTE_CONF_PORT_SEL_CSR,
 113                                   (u32)route_port);
 114         udelay(10);
 115 
 116         return 0;
 117 }
 118 
 119 static int
 120 idtg2_route_get_entry(struct rio_mport *mport, u16 destid, u8 hopcount,
 121                        u16 table, u16 route_destid, u8 *route_port)
 122 {
 123         u32 result;
 124 
 125         /*
 126          * Select routing table to read
 127          */
 128         if (table == RIO_GLOBAL_TABLE)
 129                 table = 0;
 130         else
 131                 table++;
 132 
 133         rio_mport_write_config_32(mport, destid, hopcount,
 134                                   LOCAL_RTE_CONF_DESTID_SEL, table);
 135 
 136         rio_mport_write_config_32(mport, destid, hopcount,
 137                                   RIO_STD_RTE_CONF_DESTID_SEL_CSR,
 138                                   route_destid);
 139 
 140         rio_mport_read_config_32(mport, destid, hopcount,
 141                                  RIO_STD_RTE_CONF_PORT_SEL_CSR, &result);
 142 
 143         if (IDT_DEFAULT_ROUTE == (u8)result || IDT_NO_ROUTE == (u8)result)
 144                 *route_port = RIO_INVALID_ROUTE;
 145         else
 146                 *route_port = (u8)result;
 147 
 148         return 0;
 149 }
 150 
 151 static int
 152 idtg2_route_clr_table(struct rio_mport *mport, u16 destid, u8 hopcount,
 153                        u16 table)
 154 {
 155         u32 i;
 156 
 157         /*
 158          * Select routing table to read
 159          */
 160         if (table == RIO_GLOBAL_TABLE)
 161                 table = 0;
 162         else
 163                 table++;
 164 
 165         rio_mport_write_config_32(mport, destid, hopcount,
 166                                   LOCAL_RTE_CONF_DESTID_SEL, table);
 167 
 168         for (i = RIO_STD_RTE_CONF_EXTCFGEN;
 169              i <= (RIO_STD_RTE_CONF_EXTCFGEN | 0xff);) {
 170                 rio_mport_write_config_32(mport, destid, hopcount,
 171                         RIO_STD_RTE_CONF_DESTID_SEL_CSR, i);
 172                 rio_mport_write_config_32(mport, destid, hopcount,
 173                         RIO_STD_RTE_CONF_PORT_SEL_CSR,
 174                         (IDT_DEFAULT_ROUTE << 24) | (IDT_DEFAULT_ROUTE << 16) |
 175                         (IDT_DEFAULT_ROUTE << 8) | IDT_DEFAULT_ROUTE);
 176                 i += 4;
 177         }
 178 
 179         return 0;
 180 }
 181 
 182 
 183 static int
 184 idtg2_set_domain(struct rio_mport *mport, u16 destid, u8 hopcount,
 185                        u8 sw_domain)
 186 {
 187         /*
 188          * Switch domain configuration operates only at global level
 189          */
 190         rio_mport_write_config_32(mport, destid, hopcount,
 191                                   IDT_RIO_DOMAIN, (u32)sw_domain);
 192         return 0;
 193 }
 194 
 195 static int
 196 idtg2_get_domain(struct rio_mport *mport, u16 destid, u8 hopcount,
 197                        u8 *sw_domain)
 198 {
 199         u32 regval;
 200 
 201         /*
 202          * Switch domain configuration operates only at global level
 203          */
 204         rio_mport_read_config_32(mport, destid, hopcount,
 205                                 IDT_RIO_DOMAIN, &regval);
 206 
 207         *sw_domain = (u8)(regval & 0xff);
 208 
 209         return 0;
 210 }
 211 
 212 static int
 213 idtg2_em_init(struct rio_dev *rdev)
 214 {
 215         u32 regval;
 216         int i, tmp;
 217 
 218         /*
 219          * This routine performs device-specific initialization only.
 220          * All standard EM configuration should be performed at upper level.
 221          */
 222 
 223         pr_debug("RIO: %s [%d:%d]\n", __func__, rdev->destid, rdev->hopcount);
 224 
 225         /* Set Port-Write info CSR: PRIO=3 and CRF=1 */
 226         rio_write_config_32(rdev, IDT_PW_INFO_CSR, 0x0000e000);
 227 
 228         /*
 229          * Configure LT LAYER error reporting.
 230          */
 231 
 232         /* Enable standard (RIO.p8) error reporting */
 233         rio_write_config_32(rdev, IDT_LT_ERR_REPORT_EN,
 234                         REM_LTL_ERR_ILLTRAN | REM_LTL_ERR_UNSOLR |
 235                         REM_LTL_ERR_UNSUPTR);
 236 
 237         /* Use Port-Writes for LT layer error reporting.
 238          * Enable per-port reset
 239          */
 240         rio_read_config_32(rdev, IDT_DEV_CTRL_1, &regval);
 241         rio_write_config_32(rdev, IDT_DEV_CTRL_1,
 242                         regval | IDT_DEV_CTRL_1_GENPW | IDT_DEV_CTRL_1_PRSTBEH);
 243 
 244         /*
 245          * Configure PORT error reporting.
 246          */
 247 
 248         /* Report all RIO.p8 errors supported by device */
 249         rio_write_config_32(rdev, IDT_PORT_ERR_REPORT_EN_BC, 0x807e8037);
 250 
 251         /* Configure reporting of implementation specific errors/events */
 252         rio_write_config_32(rdev, IDT_PORT_ISERR_REPORT_EN_BC,
 253                             IDT_PORT_INIT_TX_ACQUIRED);
 254 
 255         /* Use Port-Writes for port error reporting and enable error logging */
 256         tmp = RIO_GET_TOTAL_PORTS(rdev->swpinfo);
 257         for (i = 0; i < tmp; i++) {
 258                 rio_read_config_32(rdev, IDT_PORT_OPS(i), &regval);
 259                 rio_write_config_32(rdev,
 260                                 IDT_PORT_OPS(i), regval | IDT_PORT_OPS_GENPW |
 261                                 IDT_PORT_OPS_PL_ELOG |
 262                                 IDT_PORT_OPS_LL_ELOG |
 263                                 IDT_PORT_OPS_LT_ELOG);
 264         }
 265         /* Overwrite error log if full */
 266         rio_write_config_32(rdev, IDT_ERR_CAP, IDT_ERR_CAP_LOG_OVERWR);
 267 
 268         /*
 269          * Configure LANE error reporting.
 270          */
 271 
 272         /* Disable line error reporting */
 273         rio_write_config_32(rdev, IDT_LANE_ERR_REPORT_EN_BC, 0);
 274 
 275         /* Use Port-Writes for lane error reporting (when enabled)
 276          * (do per-lane update because lanes may have different configuration)
 277          */
 278         tmp = (rdev->did == RIO_DID_IDTCPS1848) ? 48 : 16;
 279         for (i = 0; i < tmp; i++) {
 280                 rio_read_config_32(rdev, IDT_LANE_CTRL(i), &regval);
 281                 rio_write_config_32(rdev, IDT_LANE_CTRL(i),
 282                                     regval | IDT_LANE_CTRL_GENPW);
 283         }
 284 
 285         /*
 286          * Configure AUX error reporting.
 287          */
 288 
 289         /* Disable JTAG and I2C Error capture */
 290         rio_write_config_32(rdev, IDT_AUX_PORT_ERR_CAP_EN, 0);
 291 
 292         /* Disable JTAG and I2C Error reporting/logging */
 293         rio_write_config_32(rdev, IDT_AUX_ERR_REPORT_EN, 0);
 294 
 295         /* Disable Port-Write notification from JTAG */
 296         rio_write_config_32(rdev, IDT_JTAG_CTRL, 0);
 297 
 298         /* Disable Port-Write notification from I2C */
 299         rio_read_config_32(rdev, IDT_I2C_MCTRL, &regval);
 300         rio_write_config_32(rdev, IDT_I2C_MCTRL, regval & ~IDT_I2C_MCTRL_GENPW);
 301 
 302         /*
 303          * Configure CFG_BLK error reporting.
 304          */
 305 
 306         /* Disable Configuration Block error capture */
 307         rio_write_config_32(rdev, IDT_CFGBLK_ERR_CAPTURE_EN, 0);
 308 
 309         /* Disable Port-Writes for Configuration Block error reporting */
 310         rio_read_config_32(rdev, IDT_CFGBLK_ERR_REPORT, &regval);
 311         rio_write_config_32(rdev, IDT_CFGBLK_ERR_REPORT,
 312                             regval & ~IDT_CFGBLK_ERR_REPORT_GENPW);
 313 
 314         /* set TVAL = ~50us */
 315         rio_write_config_32(rdev,
 316                 rdev->phys_efptr + RIO_PORT_LINKTO_CTL_CSR, 0x8e << 8);
 317 
 318         return 0;
 319 }
 320 
 321 static int
 322 idtg2_em_handler(struct rio_dev *rdev, u8 portnum)
 323 {
 324         u32 regval, em_perrdet, em_ltlerrdet;
 325 
 326         rio_read_config_32(rdev,
 327                 rdev->em_efptr + RIO_EM_LTL_ERR_DETECT, &em_ltlerrdet);
 328         if (em_ltlerrdet) {
 329                 /* Service Logical/Transport Layer Error(s) */
 330                 if (em_ltlerrdet & REM_LTL_ERR_IMPSPEC) {
 331                         /* Implementation specific error reported */
 332                         rio_read_config_32(rdev,
 333                                         IDT_ISLTL_ADDRESS_CAP, &regval);
 334 
 335                         pr_debug("RIO: %s Implementation Specific LTL errors" \
 336                                  " 0x%x @(0x%x)\n",
 337                                  rio_name(rdev), em_ltlerrdet, regval);
 338 
 339                         /* Clear implementation specific address capture CSR */
 340                         rio_write_config_32(rdev, IDT_ISLTL_ADDRESS_CAP, 0);
 341 
 342                 }
 343         }
 344 
 345         rio_read_config_32(rdev,
 346                 rdev->em_efptr + RIO_EM_PN_ERR_DETECT(portnum), &em_perrdet);
 347         if (em_perrdet) {
 348                 /* Service Port-Level Error(s) */
 349                 if (em_perrdet & REM_PED_IMPL_SPEC) {
 350                         /* Implementation Specific port error reported */
 351 
 352                         /* Get IS errors reported */
 353                         rio_read_config_32(rdev,
 354                                         IDT_PORT_ISERR_DET(portnum), &regval);
 355 
 356                         pr_debug("RIO: %s Implementation Specific Port" \
 357                                  " errors 0x%x\n", rio_name(rdev), regval);
 358 
 359                         /* Clear all implementation specific events */
 360                         rio_write_config_32(rdev,
 361                                         IDT_PORT_ISERR_DET(portnum), 0);
 362                 }
 363         }
 364 
 365         return 0;
 366 }
 367 
 368 static ssize_t
 369 idtg2_show_errlog(struct device *dev, struct device_attribute *attr, char *buf)
 370 {
 371         struct rio_dev *rdev = to_rio_dev(dev);
 372         ssize_t len = 0;
 373         u32 regval;
 374 
 375         while (!rio_read_config_32(rdev, IDT_ERR_RD, &regval)) {
 376                 if (!regval)    /* 0 = end of log */
 377                         break;
 378                 len += snprintf(buf + len, PAGE_SIZE - len,
 379                                         "%08x\n", regval);
 380                 if (len >= (PAGE_SIZE - 10))
 381                         break;
 382         }
 383 
 384         return len;
 385 }
 386 
 387 static DEVICE_ATTR(errlog, S_IRUGO, idtg2_show_errlog, NULL);
 388 
 389 static int idtg2_sysfs(struct rio_dev *rdev, bool create)
 390 {
 391         struct device *dev = &rdev->dev;
 392         int err = 0;
 393 
 394         if (create) {
 395                 /* Initialize sysfs entries */
 396                 err = device_create_file(dev, &dev_attr_errlog);
 397                 if (err)
 398                         dev_err(dev, "Unable create sysfs errlog file\n");
 399         } else
 400                 device_remove_file(dev, &dev_attr_errlog);
 401 
 402         return err;
 403 }
 404 
 405 static struct rio_switch_ops idtg2_switch_ops = {
 406         .owner = THIS_MODULE,
 407         .add_entry = idtg2_route_add_entry,
 408         .get_entry = idtg2_route_get_entry,
 409         .clr_table = idtg2_route_clr_table,
 410         .set_domain = idtg2_set_domain,
 411         .get_domain = idtg2_get_domain,
 412         .em_init = idtg2_em_init,
 413         .em_handle = idtg2_em_handler,
 414 };
 415 
 416 static int idtg2_probe(struct rio_dev *rdev, const struct rio_device_id *id)
 417 {
 418         pr_debug("RIO: %s for %s\n", __func__, rio_name(rdev));
 419 
 420         spin_lock(&rdev->rswitch->lock);
 421 
 422         if (rdev->rswitch->ops) {
 423                 spin_unlock(&rdev->rswitch->lock);
 424                 return -EINVAL;
 425         }
 426 
 427         rdev->rswitch->ops = &idtg2_switch_ops;
 428 
 429         if (rdev->do_enum) {
 430                 /* Ensure that default routing is disabled on startup */
 431                 rio_write_config_32(rdev,
 432                                     RIO_STD_RTE_DEFAULT_PORT, IDT_NO_ROUTE);
 433         }
 434 
 435         spin_unlock(&rdev->rswitch->lock);
 436 
 437         /* Create device-specific sysfs attributes */
 438         idtg2_sysfs(rdev, true);
 439 
 440         return 0;
 441 }
 442 
 443 static void idtg2_remove(struct rio_dev *rdev)
 444 {
 445         pr_debug("RIO: %s for %s\n", __func__, rio_name(rdev));
 446         spin_lock(&rdev->rswitch->lock);
 447         if (rdev->rswitch->ops != &idtg2_switch_ops) {
 448                 spin_unlock(&rdev->rswitch->lock);
 449                 return;
 450         }
 451         rdev->rswitch->ops = NULL;
 452         spin_unlock(&rdev->rswitch->lock);
 453         /* Remove device-specific sysfs attributes */
 454         idtg2_sysfs(rdev, false);
 455 }
 456 
 457 static const struct rio_device_id idtg2_id_table[] = {
 458         {RIO_DEVICE(RIO_DID_IDTCPS1848, RIO_VID_IDT)},
 459         {RIO_DEVICE(RIO_DID_IDTCPS1616, RIO_VID_IDT)},
 460         {RIO_DEVICE(RIO_DID_IDTVPS1616, RIO_VID_IDT)},
 461         {RIO_DEVICE(RIO_DID_IDTSPS1616, RIO_VID_IDT)},
 462         {RIO_DEVICE(RIO_DID_IDTCPS1432, RIO_VID_IDT)},
 463         { 0, }  /* terminate list */
 464 };
 465 
 466 static struct rio_driver idtg2_driver = {
 467         .name = "idt_gen2",
 468         .id_table = idtg2_id_table,
 469         .probe = idtg2_probe,
 470         .remove = idtg2_remove,
 471 };
 472 
 473 static int __init idtg2_init(void)
 474 {
 475         return rio_register_driver(&idtg2_driver);
 476 }
 477 
 478 static void __exit idtg2_exit(void)
 479 {
 480         pr_debug("RIO: %s\n", __func__);
 481         rio_unregister_driver(&idtg2_driver);
 482         pr_debug("RIO: %s done\n", __func__);
 483 }
 484 
 485 device_initcall(idtg2_init);
 486 module_exit(idtg2_exit);
 487 
 488 MODULE_DESCRIPTION("IDT CPS Gen.2 Serial RapidIO switch family driver");
 489 MODULE_AUTHOR("Integrated Device Technology, Inc.");
 490 MODULE_LICENSE("GPL");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/rapidio/switches/idt_gen2.c

DEFINITIONS
