root/drivers/tty/serial/8250/serial_cs.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. quirk_setup_brainboxes_0104
  2. quirk_post_ibm
  3. quirk_config_nokia
  4. quirk_wakeup_oxsemi
  5. quirk_wakeup_possio_gcc
  6. quirk_config_socket
  7. serial_remove
  8. serial_suspend
  9. serial_resume
  10. serial_probe
  11. serial_detach
  12. setup_serial
  13. pfc_config
  14. simple_config_check
  15. simple_config_check_notpicky
  16. simple_config
  17. multi_config_check
  18. multi_config_check_notpicky
  19. multi_config
  20. serial_check_for_multi
  21. serial_config

   1 // SPDX-License-Identifier: (GPL-2.0 OR MPL-1.1)
   2 /*======================================================================
   3 
   4     A driver for PCMCIA serial devices
   5 
   6     serial_cs.c 1.134 2002/05/04 05:48:53
   7 
   8     The contents of this file are subject to the Mozilla Public
   9     License Version 1.1 (the "License"); you may not use this file
  10     except in compliance with the License. You may obtain a copy of
  11     the License at http://www.mozilla.org/MPL/
  12 
  13     Software distributed under the License is distributed on an "AS
  14     IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
  15     implied. See the License for the specific language governing
  16     rights and limitations under the License.
  17 
  18     The initial developer of the original code is David A. Hinds
  19     <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
  20     are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
  21 
  22     Alternatively, the contents of this file may be used under the
  23     terms of the GNU General Public License version 2 (the "GPL"), in which
  24     case the provisions of the GPL are applicable instead of the
  25     above.  If you wish to allow the use of your version of this file
  26     only under the terms of the GPL and not to allow others to use
  27     your version of this file under the MPL, indicate your decision
  28     by deleting the provisions above and replace them with the notice
  29     and other provisions required by the GPL.  If you do not delete
  30     the provisions above, a recipient may use your version of this
  31     file under either the MPL or the GPL.
  32 
  33 ======================================================================*/
  34 
  35 #include <linux/module.h>
  36 #include <linux/moduleparam.h>
  37 #include <linux/kernel.h>
  38 #include <linux/ptrace.h>
  39 #include <linux/slab.h>
  40 #include <linux/string.h>
  41 #include <linux/timer.h>
  42 #include <linux/serial_core.h>
  43 #include <linux/delay.h>
  44 #include <linux/major.h>
  45 #include <asm/io.h>
  46 
  47 #include <pcmcia/cistpl.h>
  48 #include <pcmcia/ciscode.h>
  49 #include <pcmcia/ds.h>
  50 #include <pcmcia/cisreg.h>
  51 
  52 #include "8250.h"
  53 
  54 
  55 /*====================================================================*/
  56 
  57 /* Parameters that can be set with 'insmod' */
  58 
  59 /* Enable the speaker? */
  60 static int do_sound = 1;
  61 /* Skip strict UART tests? */
  62 static int buggy_uart;
  63 
  64 module_param(do_sound, int, 0444);
  65 module_param(buggy_uart, int, 0444);
  66 
  67 /*====================================================================*/
  68 
  69 /* Table of multi-port card ID's */
  70 
  71 struct serial_quirk {
  72         unsigned int manfid;
  73         unsigned int prodid;
  74         int multi;              /* 1 = multifunction, > 1 = # ports */
  75         void (*config)(struct pcmcia_device *);
  76         void (*setup)(struct pcmcia_device *, struct uart_8250_port *);
  77         void (*wakeup)(struct pcmcia_device *);
  78         int (*post)(struct pcmcia_device *);
  79 };
  80 
  81 struct serial_info {
  82         struct pcmcia_device    *p_dev;
  83         int                     ndev;
  84         int                     multi;
  85         int                     slave;
  86         int                     manfid;
  87         int                     prodid;
  88         int                     c950ctrl;
  89         int                     line[4];
  90         const struct serial_quirk *quirk;
  91 };
  92 
  93 struct serial_cfg_mem {
  94         tuple_t tuple;
  95         cisparse_t parse;
  96         u_char buf[256];
  97 };
  98 
  99 /*
 100  * vers_1 5.0, "Brain Boxes", "2-Port RS232 card", "r6"
 101  * manfid 0x0160, 0x0104
 102  * This card appears to have a 14.7456MHz clock.
 103  */
 104 /* Generic Modem: MD55x (GPRS/EDGE) have
 105  * Elan VPU16551 UART with 14.7456MHz oscillator
 106  * manfid 0x015D, 0x4C45
 107  */
 108 static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_8250_port *uart)
 109 {
 110         uart->port.uartclk = 14745600;
 111 }
 112 
 113 static int quirk_post_ibm(struct pcmcia_device *link)
 114 {
 115         u8 val;
 116         int ret;
 117 
 118         ret = pcmcia_read_config_byte(link, 0x800, &val);
 119         if (ret)
 120                 goto failed;
 121 
 122         ret = pcmcia_write_config_byte(link, 0x800, val | 1);
 123         if (ret)
 124                 goto failed;
 125         return 0;
 126 
 127  failed:
 128         return -ENODEV;
 129 }
 130 
 131 /*
 132  * Nokia cards are not really multiport cards.  Shouldn't this
 133  * be handled by setting the quirk entry .multi = 0 | 1 ?
 134  */
 135 static void quirk_config_nokia(struct pcmcia_device *link)
 136 {
 137         struct serial_info *info = link->priv;
 138 
 139         if (info->multi > 1)
 140                 info->multi = 1;
 141 }
 142 
 143 static void quirk_wakeup_oxsemi(struct pcmcia_device *link)
 144 {
 145         struct serial_info *info = link->priv;
 146 
 147         if (info->c950ctrl)
 148                 outb(12, info->c950ctrl + 1);
 149 }
 150 
 151 /* request_region? oxsemi branch does no request_region too... */
 152 /*
 153  * This sequence is needed to properly initialize MC45 attached to OXCF950.
 154  * I tried decreasing these msleep()s, but it worked properly (survived
 155  * 1000 stop/start operations) with these timeouts (or bigger).
 156  */
 157 static void quirk_wakeup_possio_gcc(struct pcmcia_device *link)
 158 {
 159         struct serial_info *info = link->priv;
 160         unsigned int ctrl = info->c950ctrl;
 161 
 162         outb(0xA, ctrl + 1);
 163         msleep(100);
 164         outb(0xE, ctrl + 1);
 165         msleep(300);
 166         outb(0xC, ctrl + 1);
 167         msleep(100);
 168         outb(0xE, ctrl + 1);
 169         msleep(200);
 170         outb(0xF, ctrl + 1);
 171         msleep(100);
 172         outb(0xE, ctrl + 1);
 173         msleep(100);
 174         outb(0xC, ctrl + 1);
 175 }
 176 
 177 /*
 178  * Socket Dual IO: this enables irq's for second port
 179  */
 180 static void quirk_config_socket(struct pcmcia_device *link)
 181 {
 182         struct serial_info *info = link->priv;
 183 
 184         if (info->multi)
 185                 link->config_flags |= CONF_ENABLE_ESR;
 186 }
 187 
 188 static const struct serial_quirk quirks[] = {
 189         {
 190                 .manfid = 0x0160,
 191                 .prodid = 0x0104,
 192                 .multi  = -1,
 193                 .setup  = quirk_setup_brainboxes_0104,
 194         }, {
 195                 .manfid = 0x015D,
 196                 .prodid = 0x4C45,
 197                 .multi  = -1,
 198                 .setup  = quirk_setup_brainboxes_0104,
 199         }, {
 200                 .manfid = MANFID_IBM,
 201                 .prodid = ~0,
 202                 .multi  = -1,
 203                 .post   = quirk_post_ibm,
 204         }, {
 205                 .manfid = MANFID_INTEL,
 206                 .prodid = PRODID_INTEL_DUAL_RS232,
 207                 .multi  = 2,
 208         }, {
 209                 .manfid = MANFID_NATINST,
 210                 .prodid = PRODID_NATINST_QUAD_RS232,
 211                 .multi  = 4,
 212         }, {
 213                 .manfid = MANFID_NOKIA,
 214                 .prodid = ~0,
 215                 .multi  = -1,
 216                 .config = quirk_config_nokia,
 217         }, {
 218                 .manfid = MANFID_OMEGA,
 219                 .prodid = PRODID_OMEGA_QSP_100,
 220                 .multi  = 4,
 221         }, {
 222                 .manfid = MANFID_OXSEMI,
 223                 .prodid = ~0,
 224                 .multi  = -1,
 225                 .wakeup = quirk_wakeup_oxsemi,
 226         }, {
 227                 .manfid = MANFID_POSSIO,
 228                 .prodid = PRODID_POSSIO_GCC,
 229                 .multi  = -1,
 230                 .wakeup = quirk_wakeup_possio_gcc,
 231         }, {
 232                 .manfid = MANFID_QUATECH,
 233                 .prodid = PRODID_QUATECH_DUAL_RS232,
 234                 .multi  = 2,
 235         }, {
 236                 .manfid = MANFID_QUATECH,
 237                 .prodid = PRODID_QUATECH_DUAL_RS232_D1,
 238                 .multi  = 2,
 239         }, {
 240                 .manfid = MANFID_QUATECH,
 241                 .prodid = PRODID_QUATECH_DUAL_RS232_G,
 242                 .multi  = 2,
 243         }, {
 244                 .manfid = MANFID_QUATECH,
 245                 .prodid = PRODID_QUATECH_QUAD_RS232,
 246                 .multi  = 4,
 247         }, {
 248                 .manfid = MANFID_SOCKET,
 249                 .prodid = PRODID_SOCKET_DUAL_RS232,
 250                 .multi  = 2,
 251                 .config = quirk_config_socket,
 252         }, {
 253                 .manfid = MANFID_SOCKET,
 254                 .prodid = ~0,
 255                 .multi  = -1,
 256                 .config = quirk_config_socket,
 257         }
 258 };
 259 
 260 
 261 static int serial_config(struct pcmcia_device *link);
 262 
 263 
 264 static void serial_remove(struct pcmcia_device *link)
 265 {
 266         struct serial_info *info = link->priv;
 267         int i;
 268 
 269         dev_dbg(&link->dev, "serial_release\n");
 270 
 271         /*
 272          * Recheck to see if the device is still configured.
 273          */
 274         for (i = 0; i < info->ndev; i++)
 275                 serial8250_unregister_port(info->line[i]);
 276 
 277         if (!info->slave)
 278                 pcmcia_disable_device(link);
 279 }
 280 
 281 static int serial_suspend(struct pcmcia_device *link)
 282 {
 283         struct serial_info *info = link->priv;
 284         int i;
 285 
 286         for (i = 0; i < info->ndev; i++)
 287                 serial8250_suspend_port(info->line[i]);
 288 
 289         return 0;
 290 }
 291 
 292 static int serial_resume(struct pcmcia_device *link)
 293 {
 294         struct serial_info *info = link->priv;
 295         int i;
 296 
 297         for (i = 0; i < info->ndev; i++)
 298                 serial8250_resume_port(info->line[i]);
 299 
 300         if (info->quirk && info->quirk->wakeup)
 301                 info->quirk->wakeup(link);
 302 
 303         return 0;
 304 }
 305 
 306 static int serial_probe(struct pcmcia_device *link)
 307 {
 308         struct serial_info *info;
 309 
 310         dev_dbg(&link->dev, "serial_attach()\n");
 311 
 312         /* Create new serial device */
 313         info = kzalloc(sizeof(*info), GFP_KERNEL);
 314         if (!info)
 315                 return -ENOMEM;
 316         info->p_dev = link;
 317         link->priv = info;
 318 
 319         link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
 320         if (do_sound)
 321                 link->config_flags |= CONF_ENABLE_SPKR;
 322 
 323         return serial_config(link);
 324 }
 325 
 326 static void serial_detach(struct pcmcia_device *link)
 327 {
 328         struct serial_info *info = link->priv;
 329 
 330         dev_dbg(&link->dev, "serial_detach\n");
 331 
 332         /*
 333          * Ensure that the ports have been released.
 334          */
 335         serial_remove(link);
 336 
 337         /* free bits */
 338         kfree(info);
 339 }
 340 
 341 /*====================================================================*/
 342 
 343 static int setup_serial(struct pcmcia_device *handle, struct serial_info *info,
 344                         unsigned int iobase, int irq)
 345 {
 346         struct uart_8250_port uart;
 347         int line;
 348 
 349         memset(&uart, 0, sizeof(uart));
 350         uart.port.iobase = iobase;
 351         uart.port.irq = irq;
 352         uart.port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ;
 353         uart.port.uartclk = 1843200;
 354         uart.port.dev = &handle->dev;
 355         if (buggy_uart)
 356                 uart.port.flags |= UPF_BUGGY_UART;
 357 
 358         if (info->quirk && info->quirk->setup)
 359                 info->quirk->setup(handle, &uart);
 360 
 361         line = serial8250_register_8250_port(&uart);
 362         if (line < 0) {
 363                 pr_err("serial_cs: serial8250_register_8250_port() at 0x%04lx, irq %d failed\n",
 364                                                         (unsigned long)iobase, irq);
 365                 return -EINVAL;
 366         }
 367 
 368         info->line[info->ndev] = line;
 369         info->ndev++;
 370 
 371         return 0;
 372 }
 373 
 374 /*====================================================================*/
 375 
 376 static int pfc_config(struct pcmcia_device *p_dev)
 377 {
 378         unsigned int port = 0;
 379         struct serial_info *info = p_dev->priv;
 380 
 381         if ((p_dev->resource[1]->end != 0) &&
 382                 (resource_size(p_dev->resource[1]) == 8)) {
 383                 port = p_dev->resource[1]->start;
 384                 info->slave = 1;
 385         } else if ((info->manfid == MANFID_OSITECH) &&
 386                 (resource_size(p_dev->resource[0]) == 0x40)) {
 387                 port = p_dev->resource[0]->start + 0x28;
 388                 info->slave = 1;
 389         }
 390         if (info->slave)
 391                 return setup_serial(p_dev, info, port, p_dev->irq);
 392 
 393         dev_warn(&p_dev->dev, "no usable port range found, giving up\n");
 394         return -ENODEV;
 395 }
 396 
 397 static int simple_config_check(struct pcmcia_device *p_dev, void *priv_data)
 398 {
 399         static const int size_table[2] = { 8, 16 };
 400         int *try = priv_data;
 401 
 402         if (p_dev->resource[0]->start == 0)
 403                 return -ENODEV;
 404 
 405         if ((*try & 0x1) == 0)
 406                 p_dev->io_lines = 16;
 407 
 408         if (p_dev->resource[0]->end != size_table[(*try >> 1)])
 409                 return -ENODEV;
 410 
 411         p_dev->resource[0]->end = 8;
 412         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 413         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 414 
 415         return pcmcia_request_io(p_dev);
 416 }
 417 
 418 static int simple_config_check_notpicky(struct pcmcia_device *p_dev,
 419                                         void *priv_data)
 420 {
 421         static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
 422         int j;
 423 
 424         if (p_dev->io_lines > 3)
 425                 return -ENODEV;
 426 
 427         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 428         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 429         p_dev->resource[0]->end = 8;
 430 
 431         for (j = 0; j < 5; j++) {
 432                 p_dev->resource[0]->start = base[j];
 433                 p_dev->io_lines = base[j] ? 16 : 3;
 434                 if (!pcmcia_request_io(p_dev))
 435                         return 0;
 436         }
 437         return -ENODEV;
 438 }
 439 
 440 static int simple_config(struct pcmcia_device *link)
 441 {
 442         struct serial_info *info = link->priv;
 443         int i = -ENODEV, try;
 444 
 445         /*
 446          * First pass: look for a config entry that looks normal.
 447          * Two tries: without IO aliases, then with aliases.
 448          */
 449         link->config_flags |= CONF_AUTO_SET_VPP;
 450         for (try = 0; try < 4; try++)
 451                 if (!pcmcia_loop_config(link, simple_config_check, &try))
 452                         goto found_port;
 453 
 454         /*
 455          * Second pass: try to find an entry that isn't picky about
 456          * its base address, then try to grab any standard serial port
 457          * address, and finally try to get any free port.
 458          */
 459         if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL))
 460                 goto found_port;
 461 
 462         dev_warn(&link->dev, "no usable port range found, giving up\n");
 463         return -1;
 464 
 465 found_port:
 466         if (info->multi && (info->manfid == MANFID_3COM))
 467                 link->config_index &= ~(0x08);
 468 
 469         /*
 470          * Apply any configuration quirks.
 471          */
 472         if (info->quirk && info->quirk->config)
 473                 info->quirk->config(link);
 474 
 475         i = pcmcia_enable_device(link);
 476         if (i != 0)
 477                 return -1;
 478         return setup_serial(link, info, link->resource[0]->start, link->irq);
 479 }
 480 
 481 static int multi_config_check(struct pcmcia_device *p_dev, void *priv_data)
 482 {
 483         int *multi = priv_data;
 484 
 485         if (p_dev->resource[1]->end)
 486                 return -EINVAL;
 487 
 488         /*
 489          * The quad port cards have bad CIS's, so just look for a
 490          * window larger than 8 ports and assume it will be right.
 491          */
 492         if (p_dev->resource[0]->end <= 8)
 493                 return -EINVAL;
 494 
 495         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 496         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 497         p_dev->resource[0]->end = *multi * 8;
 498 
 499         if (pcmcia_request_io(p_dev))
 500                 return -ENODEV;
 501         return 0;
 502 }
 503 
 504 static int multi_config_check_notpicky(struct pcmcia_device *p_dev,
 505                                        void *priv_data)
 506 {
 507         int *base2 = priv_data;
 508 
 509         if (!p_dev->resource[0]->end || !p_dev->resource[1]->end ||
 510                 p_dev->resource[0]->start + 8 != p_dev->resource[1]->start)
 511                 return -ENODEV;
 512 
 513         p_dev->resource[0]->end = p_dev->resource[1]->end = 8;
 514         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 515         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
 516 
 517         if (pcmcia_request_io(p_dev))
 518                 return -ENODEV;
 519 
 520         *base2 = p_dev->resource[0]->start + 8;
 521         return 0;
 522 }
 523 
 524 static int multi_config(struct pcmcia_device *link)
 525 {
 526         struct serial_info *info = link->priv;
 527         int i, base2 = 0;
 528 
 529         /* First, look for a generic full-sized window */
 530         if (!pcmcia_loop_config(link, multi_config_check, &info->multi))
 531                 base2 = link->resource[0]->start + 8;
 532         else {
 533                 /* If that didn't work, look for two windows */
 534                 info->multi = 2;
 535                 if (pcmcia_loop_config(link, multi_config_check_notpicky,
 536                                        &base2)) {
 537                         dev_warn(&link->dev,
 538                                  "no usable port range found, giving up\n");
 539                         return -ENODEV;
 540                 }
 541         }
 542 
 543         if (!link->irq)
 544                 dev_warn(&link->dev, "no usable IRQ found, continuing...\n");
 545 
 546         /*
 547          * Apply any configuration quirks.
 548          */
 549         if (info->quirk && info->quirk->config)
 550                 info->quirk->config(link);
 551 
 552         i = pcmcia_enable_device(link);
 553         if (i != 0)
 554                 return -ENODEV;
 555 
 556         /* The Oxford Semiconductor OXCF950 cards are in fact single-port:
 557          * 8 registers are for the UART, the others are extra registers.
 558          * Siemen's MC45 PCMCIA (Possio's GCC) is OXCF950 based too.
 559          */
 560         if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO &&
 561                                 info->prodid == PRODID_POSSIO_GCC)) {
 562                 int err;
 563 
 564                 if (link->config_index == 1 ||
 565                     link->config_index == 3) {
 566                         err = setup_serial(link, info, base2,
 567                                         link->irq);
 568                         base2 = link->resource[0]->start;
 569                 } else {
 570                         err = setup_serial(link, info, link->resource[0]->start,
 571                                         link->irq);
 572                 }
 573                 info->c950ctrl = base2;
 574 
 575                 /*
 576                  * FIXME: We really should wake up the port prior to
 577                  * handing it over to the serial layer.
 578                  */
 579                 if (info->quirk && info->quirk->wakeup)
 580                         info->quirk->wakeup(link);
 581 
 582                 return 0;
 583         }
 584 
 585         setup_serial(link, info, link->resource[0]->start, link->irq);
 586         for (i = 0; i < info->multi - 1; i++)
 587                 setup_serial(link, info, base2 + (8 * i),
 588                                 link->irq);
 589         return 0;
 590 }
 591 
 592 static int serial_check_for_multi(struct pcmcia_device *p_dev,  void *priv_data)
 593 {
 594         struct serial_info *info = p_dev->priv;
 595 
 596         if (!p_dev->resource[0]->end)
 597                 return -EINVAL;
 598 
 599         if ((!p_dev->resource[1]->end) && (p_dev->resource[0]->end % 8 == 0))
 600                 info->multi = p_dev->resource[0]->end >> 3;
 601 
 602         if ((p_dev->resource[1]->end) && (p_dev->resource[0]->end == 8)
 603                 && (p_dev->resource[1]->end == 8))
 604                 info->multi = 2;
 605 
 606         return 0; /* break */
 607 }
 608 
 609 
 610 static int serial_config(struct pcmcia_device *link)
 611 {
 612         struct serial_info *info = link->priv;
 613         int i;
 614 
 615         dev_dbg(&link->dev, "serial_config\n");
 616 
 617         /* Is this a compliant multifunction card? */
 618         info->multi = (link->socket->functions > 1);
 619 
 620         /* Is this a multiport card? */
 621         info->manfid = link->manf_id;
 622         info->prodid = link->card_id;
 623 
 624         for (i = 0; i < ARRAY_SIZE(quirks); i++)
 625                 if ((quirks[i].manfid == ~0 ||
 626                      quirks[i].manfid == info->manfid) &&
 627                     (quirks[i].prodid == ~0 ||
 628                      quirks[i].prodid == info->prodid)) {
 629                         info->quirk = &quirks[i];
 630                         break;
 631                 }
 632 
 633         /*
 634          * Another check for dual-serial cards: look for either serial or
 635          * multifunction cards that ask for appropriate IO port ranges.
 636          */
 637         if ((info->multi == 0) &&
 638             (link->has_func_id) &&
 639             (link->socket->pcmcia_pfc == 0) &&
 640             ((link->func_id == CISTPL_FUNCID_MULTI) ||
 641              (link->func_id == CISTPL_FUNCID_SERIAL))) {
 642                 if (pcmcia_loop_config(link, serial_check_for_multi, info))
 643                         goto failed;
 644         }
 645 
 646         /*
 647          * Apply any multi-port quirk.
 648          */
 649         if (info->quirk && info->quirk->multi != -1)
 650                 info->multi = info->quirk->multi;
 651 
 652         dev_info(&link->dev,
 653                 "trying to set up [0x%04x:0x%04x] (pfc: %d, multi: %d, quirk: %p)\n",
 654                 link->manf_id, link->card_id,
 655                 link->socket->pcmcia_pfc, info->multi, info->quirk);
 656         if (link->socket->pcmcia_pfc)
 657                 i = pfc_config(link);
 658         else if (info->multi > 1)
 659                 i = multi_config(link);
 660         else
 661                 i = simple_config(link);
 662 
 663         if (i || info->ndev == 0)
 664                 goto failed;
 665 
 666         /*
 667          * Apply any post-init quirk.  FIXME: This should really happen
 668          * before we register the port, since it might already be in use.
 669          */
 670         if (info->quirk && info->quirk->post)
 671                 if (info->quirk->post(link))
 672                         goto failed;
 673 
 674         return 0;
 675 
 676 failed:
 677         dev_warn(&link->dev, "failed to initialize\n");
 678         serial_remove(link);
 679         return -ENODEV;
 680 }
 681 
 682 static const struct pcmcia_device_id serial_ids[] = {
 683         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0057, 0x0021),
 684         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0089, 0x110a),
 685         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0104, 0x000a),
 686         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0d0a),
 687         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0e0a),
 688         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0xea15),
 689         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0109, 0x0501),
 690         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0138, 0x110a),
 691         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0140, 0x000a),
 692         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0x3341),
 693         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0xc0ab),
 694         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x016c, 0x0081),
 695         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x021b, 0x0101),
 696         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x08a1, 0xc0ab),
 697         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3288", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x04cd2988, 0x46a52d63),
 698         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3336", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x0143b773, 0x46a52d63),
 699         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "EM1144T", "PCMCIA MODEM", 0xf510db04, 0x856d66c8, 0xbd6c43ef),
 700         PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "XJEM1144/CCEM1144", "PCMCIA MODEM", 0xf510db04, 0x52d21e1e, 0xbd6c43ef),
 701         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM28", 0x2e3ee845, 0x0ea978ea),
 702         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM33", 0x2e3ee845, 0x80609023),
 703         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM56", 0x2e3ee845, 0xa650c32a),
 704         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "REM10", 0x2e3ee845, 0x76df1d29),
 705         PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "XEM5600", 0x2e3ee845, 0xf1403719),
 706         PCMCIA_PFC_DEVICE_PROD_ID12(1, "AnyCom", "Fast Ethernet + 56K COMBO", 0x578ba6e7, 0xb0ac62c4),
 707         PCMCIA_PFC_DEVICE_PROD_ID12(1, "ATKK", "LM33-PCM-T", 0xba9eb7e2, 0x077c174e),
 708         PCMCIA_PFC_DEVICE_PROD_ID12(1, "D-Link", "DME336T", 0x1a424a1c, 0xb23897ff),
 709         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Gateway 2000", "XJEM3336", 0xdd9989be, 0x662c394c),
 710         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae),
 711         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033),
 712         PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58),
 713         PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e),
 714         PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555),
 715         PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001", 0x18df0ba0, 0x831b1064),
 716         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9),
 717         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed),
 718         PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc),
 719         PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f),
 720         PCMCIA_PFC_DEVICE_PROD_ID12(1, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed),
 721         PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf),
 722         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0e01),
 723         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05),
 724         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0b05),
 725         PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101),
 726         PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070),
 727         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562),
 728         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0104, 0x0070),
 729         PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x016c, 0x0020),
 730         PCMCIA_MFC_DEVICE_PROD_ID123(1, "APEX DATA", "MULTICARD", "ETHERNET-MODEM", 0x11c2da09, 0x7289dc5d, 0xaad95e1f),
 731         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away 28.8 PC Card       ", 0xb569a6e5, 0x5bd4ff2c),
 732         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away Credit Card Adapter", 0xb569a6e5, 0x4bdf15c3),
 733         PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "w95 Home and Away Credit Card ", 0xb569a6e5, 0xae911c15),
 734         PCMCIA_MFC_DEVICE_PROD_ID1(1, "Motorola MARQUIS", 0xf03e4e77),
 735         PCMCIA_MFC_DEVICE_PROD_ID2(1, "FAX/Modem/Ethernet Combo Card ", 0x1ed59302),
 736         PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0301),
 737         PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x0276),
 738         PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0039),
 739         PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0006),
 740         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x0101), /* TDK DF2814 */
 741         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x100a), /* Xircom CM-56G */
 742         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x3e0a), /* TDK DF5660 */
 743         PCMCIA_DEVICE_MANF_CARD(0x0105, 0x410a),
 744         PCMCIA_DEVICE_MANF_CARD(0x0107, 0x0002), /* USRobotics 14,400 */
 745         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d50),
 746         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d51),
 747         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d52),
 748         PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d53),
 749         PCMCIA_DEVICE_MANF_CARD(0x010b, 0xd180),
 750         PCMCIA_DEVICE_MANF_CARD(0x0115, 0x3330), /* USRobotics/SUN 14,400 */
 751         PCMCIA_DEVICE_MANF_CARD(0x0124, 0x0100), /* Nokia DTP-2 ver II */
 752         PCMCIA_DEVICE_MANF_CARD(0x0134, 0x5600), /* LASAT COMMUNICATIONS A/S */
 753         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x000e),
 754         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x001b),
 755         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0025),
 756         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0045),
 757         PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0052),
 758         PCMCIA_DEVICE_MANF_CARD(0x016c, 0x0006), /* Psion 56K+Fax */
 759         PCMCIA_DEVICE_MANF_CARD(0x0200, 0x0001), /* MultiMobile */
 760         PCMCIA_DEVICE_PROD_ID134("ADV", "TECH", "COMpad-32/85", 0x67459937, 0x916d02ba, 0x8fbe92ae),
 761         PCMCIA_DEVICE_PROD_ID124("GATEWAY2000", "CC3144", "PCMCIA MODEM", 0x506bccae, 0xcb3685f1, 0xbd6c43ef),
 762         PCMCIA_DEVICE_PROD_ID14("MEGAHERTZ", "PCMCIA MODEM", 0xf510db04, 0xbd6c43ef),
 763         PCMCIA_DEVICE_PROD_ID124("TOSHIBA", "T144PF", "PCMCIA MODEM", 0xb4585a1a, 0x7271409c, 0xbd6c43ef),
 764         PCMCIA_DEVICE_PROD_ID123("FUJITSU", "FC14F ", "MBH10213", 0x6ee5a3d8, 0x30ead12b, 0xb00f05a0),
 765         PCMCIA_DEVICE_PROD_ID123("Novatel Wireless", "Merlin UMTS Modem", "U630", 0x32607776, 0xd9e73b13, 0xe87332e),
 766         PCMCIA_DEVICE_PROD_ID13("MEGAHERTZ", "V.34 PCMCIA MODEM", 0xf510db04, 0xbb2cce4a),
 767         PCMCIA_DEVICE_PROD_ID12("Brain Boxes", "Bluetooth PC Card", 0xee138382, 0xd4ce9b02),
 768         PCMCIA_DEVICE_PROD_ID12("CIRRUS LOGIC", "FAX MODEM", 0xe625f451, 0xcecd6dfa),
 769         PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 28800 FAX/DATA MODEM", 0xa3a3062c, 0x8cbd7c76),
 770         PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 33600 FAX/DATA MODEM", 0xa3a3062c, 0x5a00ce95),
 771         PCMCIA_DEVICE_PROD_ID12("Computerboards, Inc.", "PCM-COM422", 0xd0b78f51, 0x7e2d49ed),
 772         PCMCIA_DEVICE_PROD_ID12("Dr. Neuhaus", "FURY CARD 14K4", 0x76942813, 0x8b96ce65),
 773         PCMCIA_DEVICE_PROD_ID12("IBM", "ISDN/56K/GSM", 0xb569a6e5, 0xfee5297b),
 774         PCMCIA_DEVICE_PROD_ID12("Intelligent", "ANGIA FAX/MODEM", 0xb496e65e, 0xf31602a6),
 775         PCMCIA_DEVICE_PROD_ID12("Intel", "MODEM 2400+", 0x816cc815, 0x412729fb),
 776         PCMCIA_DEVICE_PROD_ID12("Intertex", "IX34-PCMCIA", 0xf8a097e3, 0x97880447),
 777         PCMCIA_DEVICE_PROD_ID12("IOTech Inc ", "PCMCIA Dual RS-232 Serial Port Card", 0x3bd2d898, 0x92abc92f),
 778         PCMCIA_DEVICE_PROD_ID12("MACRONIX", "FAX/MODEM", 0x668388b3, 0x3f9bdf2f),
 779         PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT1432LT", 0x5f73be51, 0x0b3e2383),
 780         PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e),
 781         PCMCIA_DEVICE_PROD_ID12("OEM      ", "C288MX     ", 0xb572d360, 0xd2385b7a),
 782         PCMCIA_DEVICE_PROD_ID12("Option International", "V34bis GSM/PSTN Data/Fax Modem", 0x9d7cd6f5, 0x5cb8bf41),
 783         PCMCIA_DEVICE_PROD_ID12("PCMCIA   ", "C336MX     ", 0x99bcafe9, 0xaa25bcab),
 784         PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f),
 785         PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d),
 786         PCMCIA_DEVICE_PROD_ID12("Telia", "SurfinBird 560P/A+", 0xe2cdd5e, 0xc9314b38),
 787         PCMCIA_DEVICE_PROD_ID1("Smart Serial Port", 0x2d8ce292),
 788         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"),
 789         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"),
 790         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"),
 791         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"),
 792         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"),
 793         PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "TOSHIBA", "Modem/LAN Card", 0xb4585a1a, 0x53f922f8, "cis/PCMLM28.cis"),
 794         PCMCIA_MFC_DEVICE_CIS_PROD_ID12(1, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "cis/DP83903.cis"),
 795         PCMCIA_MFC_DEVICE_CIS_PROD_ID4(1, "NSC MF LAN/Modem", 0x58fc6056, "cis/DP83903.cis"),
 796         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0556, "cis/3CCFEM556.cis"),
 797         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0175, 0x0000, "cis/DP83903.cis"),
 798         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0035, "cis/3CXEM556.cis"),
 799         PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x003d, "cis/3CXEM556.cis"),
 800         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC850", 0xd85f6206, 0x42a2c018, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC850 3G Network Adapter R1 */
 801         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC860", 0xd85f6206, 0x698f93db, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC860 3G Network Adapter R1 */
 802         PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC710/AC750", 0xd85f6206, 0x761b11e0, "cis/SW_7xx_SER.cis"),  /* Sierra Wireless AC710/AC750 GPRS Network Adapter R1 */
 803         PCMCIA_DEVICE_CIS_MANF_CARD(0x0192, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- pre update */
 804         PCMCIA_DEVICE_CIS_MANF_CARD(0x013f, 0xa555, "cis/SW_555_SER.cis"),  /* Sierra Aircard 555 CDMA 1xrtt Modem -- post update */
 805         PCMCIA_DEVICE_CIS_PROD_ID12("MultiTech", "PCMCIA 56K DataFax", 0x842047ee, 0xc2efcf03, "cis/MT5634ZLX.cis"),
 806         PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-2", 0x96913a85, 0x27ab5437, "cis/COMpad2.cis"),
 807         PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"),
 808         PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"),
 809         PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"),
 810         PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"),
 811         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100  1.00.", 0x19ca78af, 0xf964f42b),
 812         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL100", 0x19ca78af, 0x71d98e83),
 813         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232  1.00.", 0x19ca78af, 0x69fb7490),
 814         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.", "SERIAL CARD: SL232", 0x19ca78af, 0xb6bc0235),
 815         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232", 0x63f2e0bd, 0xb9e175d3),
 816         PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.", "SERIAL CARD: CF232-5", 0x63f2e0bd, 0xfce33442),
 817         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232", 0x3beb8cf2, 0x171e7190),
 818         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF232-5", 0x3beb8cf2, 0x20da4262),
 819         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF428", 0x3beb8cf2, 0xea5dd57d),
 820         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: CF500", 0x3beb8cf2, 0xd77255fa),
 821         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: IC232", 0x3beb8cf2, 0x6a709903),
 822         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: SL232", 0x3beb8cf2, 0x18430676),
 823         PCMCIA_DEVICE_PROD_ID12("Elan", "Serial Port: XL232", 0x3beb8cf2, 0x6f933767),
 824         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
 825         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
 826         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
 827         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 828         PCMCIA_MFC_DEVICE_PROD_ID12(0, "Elan", "Serial+Parallel Port: SP230", 0x3beb8cf2, 0xdb9e58bc),
 829         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: CF332", 0x3beb8cf2, 0x16dc1ba7),
 830         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL332", 0x3beb8cf2, 0x19816c41),
 831         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL385", 0x3beb8cf2, 0x64112029),
 832         PCMCIA_MFC_DEVICE_PROD_ID12(1, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 833         PCMCIA_MFC_DEVICE_PROD_ID12(2, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 834         PCMCIA_MFC_DEVICE_PROD_ID12(3, "Elan", "Serial Port: SL432", 0x3beb8cf2, 0x1cce7ac4),
 835         PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b),
 836         /* too generic */
 837         /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */
 838         /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */
 839         PCMCIA_DEVICE_FUNC_ID(2),
 840         PCMCIA_DEVICE_NULL,
 841 };
 842 MODULE_DEVICE_TABLE(pcmcia, serial_ids);
 843 
 844 MODULE_FIRMWARE("cis/PCMLM28.cis");
 845 MODULE_FIRMWARE("cis/DP83903.cis");
 846 MODULE_FIRMWARE("cis/3CCFEM556.cis");
 847 MODULE_FIRMWARE("cis/3CXEM556.cis");
 848 MODULE_FIRMWARE("cis/SW_8xx_SER.cis");
 849 MODULE_FIRMWARE("cis/SW_7xx_SER.cis");
 850 MODULE_FIRMWARE("cis/SW_555_SER.cis");
 851 MODULE_FIRMWARE("cis/MT5634ZLX.cis");
 852 MODULE_FIRMWARE("cis/COMpad2.cis");
 853 MODULE_FIRMWARE("cis/COMpad4.cis");
 854 MODULE_FIRMWARE("cis/RS-COM-2P.cis");
 855 
 856 static struct pcmcia_driver serial_cs_driver = {
 857         .owner          = THIS_MODULE,
 858         .name           = "serial_cs",
 859         .probe          = serial_probe,
 860         .remove         = serial_detach,
 861         .id_table       = serial_ids,
 862         .suspend        = serial_suspend,
 863         .resume         = serial_resume,
 864 };
 865 module_pcmcia_driver(serial_cs_driver);
 866 
 867 MODULE_LICENSE("GPL");

/* [<][>][^][v][top][bottom][index][help] */