drivers/phy/marvell/phy-mvebu-a3700-utmi.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
mvebu_a3700_utmi_phy_power_on
mvebu_a3700_utmi_phy_power_off
mvebu_a3700_utmi_phy_probe
   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (C) 2018 Marvell
   4  *
   5  * Authors:
   6  *   Igal Liberman <igall@marvell.com>
   7  *   Miquèl Raynal <miquel.raynal@bootlin.com>
   8  *
   9  * Marvell A3700 UTMI PHY driver
  10  */
  11 
  12 #include <linux/io.h>
  13 #include <linux/iopoll.h>
  14 #include <linux/mfd/syscon.h>
  15 #include <linux/module.h>
  16 #include <linux/of_device.h>
  17 #include <linux/phy/phy.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/regmap.h>
  20 
  21 /* Armada 3700 UTMI PHY registers */
  22 #define USB2_PHY_PLL_CTRL_REG0                  0x0
  23 #define   PLL_REF_DIV_OFF                       0
  24 #define   PLL_REF_DIV_MASK                      GENMASK(6, 0)
  25 #define   PLL_REF_DIV_5                         5
  26 #define   PLL_FB_DIV_OFF                        16
  27 #define   PLL_FB_DIV_MASK                       GENMASK(24, 16)
  28 #define   PLL_FB_DIV_96                         96
  29 #define   PLL_SEL_LPFR_OFF                      28
  30 #define   PLL_SEL_LPFR_MASK                     GENMASK(29, 28)
  31 #define   PLL_READY                             BIT(31)
  32 #define USB2_PHY_CAL_CTRL                       0x8
  33 #define   PHY_PLLCAL_DONE                       BIT(31)
  34 #define   PHY_IMPCAL_DONE                       BIT(23)
  35 #define USB2_RX_CHAN_CTRL1                      0x18
  36 #define   USB2PHY_SQCAL_DONE                    BIT(31)
  37 #define USB2_PHY_OTG_CTRL                       0x34
  38 #define   PHY_PU_OTG                            BIT(4)
  39 #define USB2_PHY_CHRGR_DETECT                   0x38
  40 #define   PHY_CDP_EN                            BIT(2)
  41 #define   PHY_DCP_EN                            BIT(3)
  42 #define   PHY_PD_EN                             BIT(4)
  43 #define   PHY_PU_CHRG_DTC                       BIT(5)
  44 #define   PHY_CDP_DM_AUTO                       BIT(7)
  45 #define   PHY_ENSWITCH_DP                       BIT(12)
  46 #define   PHY_ENSWITCH_DM                       BIT(13)
  47 
  48 /* Armada 3700 USB miscellaneous registers */
  49 #define USB2_PHY_CTRL(usb32)                    (usb32 ? 0x20 : 0x4)
  50 #define   RB_USB2PHY_PU                         BIT(0)
  51 #define   USB2_DP_PULLDN_DEV_MODE               BIT(5)
  52 #define   USB2_DM_PULLDN_DEV_MODE               BIT(6)
  53 #define   RB_USB2PHY_SUSPM(usb32)               (usb32 ? BIT(14) : BIT(7))
  54 
  55 #define PLL_LOCK_DELAY_US                       10000
  56 #define PLL_LOCK_TIMEOUT_US                     1000000
  57 
  58 /**
  59  * struct mvebu_a3700_utmi_caps - PHY capabilities
  60  *
  61  * @usb32: Flag indicating which PHY is in use (impacts the register map):
  62  *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
  63  *           - The UTMI PHY wired to the USB2 controller (host only)
  64  * @ops: PHY operations
  65  */
  66 struct mvebu_a3700_utmi_caps {
  67         int usb32;
  68         const struct phy_ops *ops;
  69 };
  70 
  71 /**
  72  * struct mvebu_a3700_utmi - PHY driver data
  73  *
  74  * @regs: PHY registers
  75  * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
  76  * @caps: PHY capabilities
  77  * @phy: PHY handle
  78  */
  79 struct mvebu_a3700_utmi {
  80         void __iomem *regs;
  81         struct regmap *usb_misc;
  82         const struct mvebu_a3700_utmi_caps *caps;
  83         struct phy *phy;
  84 };
  85 
  86 static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
  87 {
  88         struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
  89         struct device *dev = &phy->dev;
  90         int usb32 = utmi->caps->usb32;
  91         int ret = 0;
  92         u32 reg;
  93 
  94         /*
  95          * Setup PLL. 40MHz clock used to be the default, being 25MHz now.
  96          * See "PLL Settings for Typical REFCLK" table.
  97          */
  98         reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
  99         reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
 100         reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF) |
 101                (PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
 102         writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
 103 
 104         /* Enable PHY pull up and disable USB2 suspend */
 105         regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
 106                            RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
 107                            RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
 108 
 109         if (usb32) {
 110                 /* Power up OTG module */
 111                 reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
 112                 reg |= PHY_PU_OTG;
 113                 writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
 114 
 115                 /* Disable PHY charger detection */
 116                 reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
 117                 reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
 118                          PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
 119                 writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
 120 
 121                 /* Disable PHY DP/DM pull-down (used for device mode) */
 122                 regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
 123                                    USB2_DP_PULLDN_DEV_MODE |
 124                                    USB2_DM_PULLDN_DEV_MODE, 0);
 125         }
 126 
 127         /* Wait for PLL calibration */
 128         ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
 129                                  reg & PHY_PLLCAL_DONE,
 130                                  PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
 131         if (ret) {
 132                 dev_err(dev, "Failed to end USB2 PLL calibration\n");
 133                 return ret;
 134         }
 135 
 136         /* Wait for impedance calibration */
 137         ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
 138                                  reg & PHY_IMPCAL_DONE,
 139                                  PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
 140         if (ret) {
 141                 dev_err(dev, "Failed to end USB2 impedance calibration\n");
 142                 return ret;
 143         }
 144 
 145         /* Wait for squelch calibration */
 146         ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
 147                                  reg & USB2PHY_SQCAL_DONE,
 148                                  PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
 149         if (ret) {
 150                 dev_err(dev, "Failed to end USB2 unknown calibration\n");
 151                 return ret;
 152         }
 153 
 154         /* Wait for PLL to be locked */
 155         ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
 156                                  reg & PLL_READY,
 157                                  PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
 158         if (ret)
 159                 dev_err(dev, "Failed to lock USB2 PLL\n");
 160 
 161         return ret;
 162 }
 163 
 164 static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
 165 {
 166         struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
 167         int usb32 = utmi->caps->usb32;
 168         u32 reg;
 169 
 170         /* Disable PHY pull-up and enable USB2 suspend */
 171         reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
 172         reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
 173         writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
 174 
 175         /* Power down OTG module */
 176         if (usb32) {
 177                 reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
 178                 reg &= ~PHY_PU_OTG;
 179                 writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
 180         }
 181 
 182         return 0;
 183 }
 184 
 185 static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
 186         .power_on = mvebu_a3700_utmi_phy_power_on,
 187         .power_off = mvebu_a3700_utmi_phy_power_off,
 188         .owner = THIS_MODULE,
 189 };
 190 
 191 static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
 192         .usb32 = true,
 193         .ops = &mvebu_a3700_utmi_phy_ops,
 194 };
 195 
 196 static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
 197         .usb32 = false,
 198         .ops = &mvebu_a3700_utmi_phy_ops,
 199 };
 200 
 201 static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
 202         {
 203                 .compatible = "marvell,a3700-utmi-otg-phy",
 204                 .data = &mvebu_a3700_utmi_otg_phy_caps,
 205         },
 206         {
 207                 .compatible = "marvell,a3700-utmi-host-phy",
 208                 .data = &mvebu_a3700_utmi_host_phy_caps,
 209         },
 210         {},
 211 };
 212 MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
 213 
 214 static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
 215 {
 216         struct device *dev = &pdev->dev;
 217         struct mvebu_a3700_utmi *utmi;
 218         struct phy_provider *provider;
 219         struct resource *res;
 220 
 221         utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
 222         if (!utmi)
 223                 return -ENOMEM;
 224 
 225         /* Get UTMI memory region */
 226         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 227         if (!res) {
 228                 dev_err(dev, "Missing UTMI PHY memory resource\n");
 229                 return -ENODEV;
 230         }
 231 
 232         utmi->regs = devm_ioremap_resource(dev, res);
 233         if (IS_ERR(utmi->regs))
 234                 return PTR_ERR(utmi->regs);
 235 
 236         /* Get miscellaneous Host/PHY region */
 237         utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
 238                                                          "marvell,usb-misc-reg");
 239         if (IS_ERR(utmi->usb_misc)) {
 240                 dev_err(dev,
 241                         "Missing USB misc purpose system controller\n");
 242                 return PTR_ERR(utmi->usb_misc);
 243         }
 244 
 245         /* Retrieve PHY capabilities */
 246         utmi->caps = of_device_get_match_data(dev);
 247 
 248         /* Instantiate the PHY */
 249         utmi->phy = devm_phy_create(dev, NULL, utmi->caps->ops);
 250         if (IS_ERR(utmi->phy)) {
 251                 dev_err(dev, "Failed to create the UTMI PHY\n");
 252                 return PTR_ERR(utmi->phy);
 253         }
 254 
 255         phy_set_drvdata(utmi->phy, utmi);
 256 
 257         /* Ensure the PHY is powered off */
 258         utmi->caps->ops->power_off(utmi->phy);
 259 
 260         provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 261 
 262         return PTR_ERR_OR_ZERO(provider);
 263 }
 264 
 265 static struct platform_driver mvebu_a3700_utmi_driver = {
 266         .probe  = mvebu_a3700_utmi_phy_probe,
 267         .driver = {
 268                 .name           = "mvebu-a3700-utmi-phy",
 269                 .of_match_table = mvebu_a3700_utmi_of_match,
 270          },
 271 };
 272 module_platform_driver(mvebu_a3700_utmi_driver);
 273 
 274 MODULE_AUTHOR("Igal Liberman <igall@marvell.com>");
 275 MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
 276 MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
 277 MODULE_LICENSE("GPL v2");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/phy/marvell/phy-mvebu-a3700-utmi.c

DEFINITIONS
