drivers/usb/gadget/udc/fsl_qe

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
qe_frame_clean
qe_frame_init
   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * drivers/usb/gadget/qe_udc.h
   4  *
   5  * Copyright (C) 2006-2008 Freescale Semiconductor, Inc. All rights reserved.
   6  *
   7  *      Xiaobo Xie <X.Xie@freescale.com>
   8  *      Li Yang <leoli@freescale.com>
   9  *
  10  * Description:
  11  * Freescale USB device/endpoint management registers
  12  */
  13 
  14 #ifndef __FSL_QE_UDC_H
  15 #define __FSL_QE_UDC_H
  16 
  17 /* SoC type */
  18 #define PORT_CPM        0
  19 #define PORT_QE         1
  20 
  21 #define USB_MAX_ENDPOINTS               4
  22 #define USB_MAX_PIPES                   USB_MAX_ENDPOINTS
  23 #define USB_EP0_MAX_SIZE                64
  24 #define USB_MAX_CTRL_PAYLOAD            0x4000
  25 #define USB_BDRING_LEN                  16
  26 #define USB_BDRING_LEN_RX               256
  27 #define USB_BDRING_LEN_TX               16
  28 #define MIN_EMPTY_BDS                   128
  29 #define MAX_DATA_BDS                    8
  30 #define USB_CRC_SIZE                    2
  31 #define USB_DIR_BOTH                    0x88
  32 #define R_BUF_MAXSIZE                   0x800
  33 #define USB_EP_PARA_ALIGNMENT           32
  34 
  35 /* USB Mode Register bit define */
  36 #define USB_MODE_EN             0x01
  37 #define USB_MODE_HOST           0x02
  38 #define USB_MODE_TEST           0x04
  39 #define USB_MODE_SFTE           0x08
  40 #define USB_MODE_RESUME         0x40
  41 #define USB_MODE_LSS            0x80
  42 
  43 /* USB Slave Address Register Mask */
  44 #define USB_SLVADDR_MASK        0x7F
  45 
  46 /* USB Endpoint register define */
  47 #define USB_EPNUM_MASK          0xF000
  48 #define USB_EPNUM_SHIFT         12
  49 
  50 #define USB_TRANS_MODE_SHIFT    8
  51 #define USB_TRANS_CTR           0x0000
  52 #define USB_TRANS_INT           0x0100
  53 #define USB_TRANS_BULK          0x0200
  54 #define USB_TRANS_ISO           0x0300
  55 
  56 #define USB_EP_MF               0x0020
  57 #define USB_EP_RTE              0x0010
  58 
  59 #define USB_THS_SHIFT           2
  60 #define USB_THS_MASK            0x000c
  61 #define USB_THS_NORMAL          0x0
  62 #define USB_THS_IGNORE_IN       0x0004
  63 #define USB_THS_NACK            0x0008
  64 #define USB_THS_STALL           0x000c
  65 
  66 #define USB_RHS_SHIFT           0
  67 #define USB_RHS_MASK            0x0003
  68 #define USB_RHS_NORMAL          0x0
  69 #define USB_RHS_IGNORE_OUT      0x0001
  70 #define USB_RHS_NACK            0x0002
  71 #define USB_RHS_STALL           0x0003
  72 
  73 #define USB_RTHS_MASK           0x000f
  74 
  75 /* USB Command Register define */
  76 #define USB_CMD_STR_FIFO        0x80
  77 #define USB_CMD_FLUSH_FIFO      0x40
  78 #define USB_CMD_ISFT            0x20
  79 #define USB_CMD_DSFT            0x10
  80 #define USB_CMD_EP_MASK         0x03
  81 
  82 /* USB Event and Mask Register define */
  83 #define USB_E_MSF_MASK          0x0800
  84 #define USB_E_SFT_MASK          0x0400
  85 #define USB_E_RESET_MASK        0x0200
  86 #define USB_E_IDLE_MASK         0x0100
  87 #define USB_E_TXE4_MASK         0x0080
  88 #define USB_E_TXE3_MASK         0x0040
  89 #define USB_E_TXE2_MASK         0x0020
  90 #define USB_E_TXE1_MASK         0x0010
  91 #define USB_E_SOF_MASK          0x0008
  92 #define USB_E_BSY_MASK          0x0004
  93 #define USB_E_TXB_MASK          0x0002
  94 #define USB_E_RXB_MASK          0x0001
  95 #define USBER_ALL_CLEAR         0x0fff
  96 
  97 #define USB_E_DEFAULT_DEVICE   (USB_E_RESET_MASK | USB_E_TXE4_MASK | \
  98                                 USB_E_TXE3_MASK | USB_E_TXE2_MASK | \
  99                                 USB_E_TXE1_MASK | USB_E_BSY_MASK | \
 100                                 USB_E_TXB_MASK | USB_E_RXB_MASK)
 101 
 102 #define USB_E_TXE_MASK         (USB_E_TXE4_MASK | USB_E_TXE3_MASK|\
 103                                  USB_E_TXE2_MASK | USB_E_TXE1_MASK)
 104 /* USB Status Register define */
 105 #define USB_IDLE_STATUS_MASK    0x01
 106 
 107 /* USB Start of Frame Timer */
 108 #define USB_USSFT_MASK          0x3FFF
 109 
 110 /* USB Frame Number Register */
 111 #define USB_USFRN_MASK          0xFFFF
 112 
 113 struct usb_device_para{
 114         u16     epptr[4];
 115         u32     rstate;
 116         u32     rptr;
 117         u16     frame_n;
 118         u16     rbcnt;
 119         u32     rtemp;
 120         u32     rxusb_data;
 121         u16     rxuptr;
 122         u8      reso[2];
 123         u32     softbl;
 124         u8      sofucrctemp;
 125 };
 126 
 127 struct usb_ep_para{
 128         u16     rbase;
 129         u16     tbase;
 130         u8      rbmr;
 131         u8      tbmr;
 132         u16     mrblr;
 133         u16     rbptr;
 134         u16     tbptr;
 135         u32     tstate;
 136         u32     tptr;
 137         u16     tcrc;
 138         u16     tbcnt;
 139         u32     ttemp;
 140         u16     txusbu_ptr;
 141         u8      reserve[2];
 142 };
 143 
 144 #define USB_BUSMODE_GBL         0x20
 145 #define USB_BUSMODE_BO_MASK     0x18
 146 #define USB_BUSMODE_BO_SHIFT    0x3
 147 #define USB_BUSMODE_BE          0x2
 148 #define USB_BUSMODE_CETM        0x04
 149 #define USB_BUSMODE_DTB         0x02
 150 
 151 /* Endpoint basic handle */
 152 #define ep_index(EP)            ((EP)->ep.desc->bEndpointAddress & 0xF)
 153 #define ep_maxpacket(EP)        ((EP)->ep.maxpacket)
 154 #define ep_is_in(EP)    ((ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
 155                         USB_DIR_IN) : ((EP)->ep.desc->bEndpointAddress \
 156                         & USB_DIR_IN) == USB_DIR_IN)
 157 
 158 /* ep0 transfer state */
 159 #define WAIT_FOR_SETUP          0
 160 #define DATA_STATE_XMIT         1
 161 #define DATA_STATE_NEED_ZLP     2
 162 #define WAIT_FOR_OUT_STATUS     3
 163 #define DATA_STATE_RECV         4
 164 
 165 /* ep tramsfer mode */
 166 #define USBP_TM_CTL     0
 167 #define USBP_TM_ISO     1
 168 #define USBP_TM_BULK    2
 169 #define USBP_TM_INT     3
 170 
 171 /*-----------------------------------------------------------------------------
 172         USB RX And TX DATA Frame
 173  -----------------------------------------------------------------------------*/
 174 struct qe_frame{
 175         u8 *data;
 176         u32 len;
 177         u32 status;
 178         u32 info;
 179 
 180         void *privdata;
 181         struct list_head node;
 182 };
 183 
 184 /* Frame structure, info field. */
 185 #define PID_DATA0              0x80000000 /* Data toggle zero */
 186 #define PID_DATA1              0x40000000 /* Data toggle one  */
 187 #define PID_SETUP              0x20000000 /* setup bit */
 188 #define SETUP_STATUS           0x10000000 /* setup status bit */
 189 #define SETADDR_STATUS         0x08000000 /* setupup address status bit */
 190 #define NO_REQ                 0x04000000 /* Frame without request */
 191 #define HOST_DATA              0x02000000 /* Host data frame */
 192 #define FIRST_PACKET_IN_FRAME  0x01000000 /* first packet in the frame */
 193 #define TOKEN_FRAME            0x00800000 /* Host token frame */
 194 #define ZLP                    0x00400000 /* Zero length packet */
 195 #define IN_TOKEN_FRAME         0x00200000 /* In token package */
 196 #define OUT_TOKEN_FRAME        0x00100000 /* Out token package */
 197 #define SETUP_TOKEN_FRAME      0x00080000 /* Setup token package */
 198 #define STALL_FRAME            0x00040000 /* Stall handshake */
 199 #define NACK_FRAME             0x00020000 /* Nack handshake */
 200 #define NO_PID                 0x00010000 /* No send PID */
 201 #define NO_CRC                 0x00008000 /* No send CRC */
 202 #define HOST_COMMAND           0x00004000 /* Host command frame   */
 203 
 204 /* Frame status field */
 205 /* Receive side */
 206 #define FRAME_OK               0x00000000 /* Frame transmitted or received OK */
 207 #define FRAME_ERROR            0x80000000 /* Error occurred on frame */
 208 #define START_FRAME_LOST       0x40000000 /* START_FRAME_LOST */
 209 #define END_FRAME_LOST         0x20000000 /* END_FRAME_LOST */
 210 #define RX_ER_NONOCT           0x10000000 /* Rx Non Octet Aligned Packet */
 211 #define RX_ER_BITSTUFF         0x08000000 /* Frame Aborted --Received packet
 212                                              with bit stuff error */
 213 #define RX_ER_CRC              0x04000000 /* Received packet with CRC error */
 214 #define RX_ER_OVERUN           0x02000000 /* Over-run occurred on reception */
 215 #define RX_ER_PID              0x01000000 /* Wrong PID received */
 216 /* Tranmit side */
 217 #define TX_ER_NAK              0x00800000 /* Received NAK handshake */
 218 #define TX_ER_STALL            0x00400000 /* Received STALL handshake */
 219 #define TX_ER_TIMEOUT          0x00200000 /* Transmit time out */
 220 #define TX_ER_UNDERUN          0x00100000 /* Transmit underrun */
 221 #define FRAME_INPROGRESS       0x00080000 /* Frame is being transmitted */
 222 #define ER_DATA_UNDERUN        0x00040000 /* Frame is shorter then expected */
 223 #define ER_DATA_OVERUN         0x00020000 /* Frame is longer then expected */
 224 
 225 /* QE USB frame operation functions */
 226 #define frame_get_length(frm) (frm->len)
 227 #define frame_set_length(frm, leng) (frm->len = leng)
 228 #define frame_get_data(frm) (frm->data)
 229 #define frame_set_data(frm, dat) (frm->data = dat)
 230 #define frame_get_info(frm) (frm->info)
 231 #define frame_set_info(frm, inf) (frm->info = inf)
 232 #define frame_get_status(frm) (frm->status)
 233 #define frame_set_status(frm, stat) (frm->status = stat)
 234 #define frame_get_privdata(frm) (frm->privdata)
 235 #define frame_set_privdata(frm, dat) (frm->privdata = dat)
 236 
 237 static inline void qe_frame_clean(struct qe_frame *frm)
 238 {
 239         frame_set_data(frm, NULL);
 240         frame_set_length(frm, 0);
 241         frame_set_status(frm, FRAME_OK);
 242         frame_set_info(frm, 0);
 243         frame_set_privdata(frm, NULL);
 244 }
 245 
 246 static inline void qe_frame_init(struct qe_frame *frm)
 247 {
 248         qe_frame_clean(frm);
 249         INIT_LIST_HEAD(&(frm->node));
 250 }
 251 
 252 struct qe_req {
 253         struct usb_request req;
 254         struct list_head queue;
 255         /* ep_queue() func will add
 256          a request->queue into a udc_ep->queue 'd tail */
 257         struct qe_ep *ep;
 258         unsigned mapped:1;
 259 };
 260 
 261 struct qe_ep {
 262         struct usb_ep ep;
 263         struct list_head queue;
 264         struct qe_udc *udc;
 265         struct usb_gadget *gadget;
 266 
 267         u8 state;
 268 
 269         struct qe_bd __iomem *rxbase;
 270         struct qe_bd __iomem *n_rxbd;
 271         struct qe_bd __iomem *e_rxbd;
 272 
 273         struct qe_bd __iomem *txbase;
 274         struct qe_bd __iomem *n_txbd;
 275         struct qe_bd __iomem *c_txbd;
 276 
 277         struct qe_frame *rxframe;
 278         u8 *rxbuffer;
 279         dma_addr_t rxbuf_d;
 280         u8 rxbufmap;
 281         unsigned char localnack;
 282         int has_data;
 283 
 284         struct qe_frame *txframe;
 285         struct qe_req *tx_req;
 286         int sent;  /*data already sent */
 287         int last;  /*data sent in the last time*/
 288 
 289         u8 dir;
 290         u8 epnum;
 291         u8 tm; /* transfer mode */
 292         u8 data01;
 293         u8 init;
 294 
 295         u8 already_seen;
 296         u8 enable_tasklet;
 297         u8 setup_stage;
 298         u32 last_io;            /* timestamp */
 299 
 300         char name[14];
 301 
 302         unsigned double_buf:1;
 303         unsigned stopped:1;
 304         unsigned fnf:1;
 305         unsigned has_dma:1;
 306 
 307         u8 ackwait;
 308         u8 dma_channel;
 309         u16 dma_counter;
 310         int lch;
 311 
 312         struct timer_list timer;
 313 };
 314 
 315 struct qe_udc {
 316         struct usb_gadget gadget;
 317         struct usb_gadget_driver *driver;
 318         struct device *dev;
 319         struct qe_ep eps[USB_MAX_ENDPOINTS];
 320         struct usb_ctrlrequest local_setup_buff;
 321         spinlock_t lock;        /* lock for set/config qe_udc */
 322         unsigned long soc_type;         /* QE or CPM soc */
 323 
 324         struct qe_req *status_req;      /* ep0 status request */
 325 
 326         /* USB and EP Parameter Block pointer */
 327         struct usb_device_para __iomem *usb_param;
 328         struct usb_ep_para __iomem *ep_param[4];
 329 
 330         u32 max_pipes;          /* Device max pipes */
 331         u32 max_use_endpts;     /* Max endpointes to be used */
 332         u32 bus_reset;          /* Device is bus reseting */
 333         u32 resume_state;       /* USB state to resume*/
 334         u32 usb_state;          /* USB current state */
 335         u32 usb_next_state;     /* USB next state */
 336         u32 ep0_state;          /* Enpoint zero state */
 337         u32 ep0_dir;            /* Enpoint zero direction: can be
 338                                 USB_DIR_IN or USB_DIR_OUT*/
 339         u32 usb_sof_count;      /* SOF count */
 340         u32 errors;             /* USB ERRORs count */
 341 
 342         u8 *tmpbuf;
 343         u32 c_start;
 344         u32 c_end;
 345 
 346         u8 *nullbuf;
 347         u8 *statusbuf;
 348         dma_addr_t nullp;
 349         u8 nullmap;
 350         u8 device_address;      /* Device USB address */
 351 
 352         unsigned int usb_clock;
 353         unsigned int usb_irq;
 354         struct usb_ctlr __iomem *usb_regs;
 355 
 356         struct tasklet_struct rx_tasklet;
 357 
 358         struct completion *done;        /* to make sure release() is done */
 359 };
 360 
 361 #define EP_STATE_IDLE   0
 362 #define EP_STATE_NACK   1
 363 #define EP_STATE_STALL  2
 364 
 365 /*
 366  * transmit BD's status
 367  */
 368 #define T_R           0x80000000         /* ready bit */
 369 #define T_W           0x20000000         /* wrap bit */
 370 #define T_I           0x10000000         /* interrupt on completion */
 371 #define T_L           0x08000000         /* last */
 372 #define T_TC          0x04000000         /* transmit CRC */
 373 #define T_CNF         0x02000000         /* wait for  transmit confirm */
 374 #define T_LSP         0x01000000         /* Low-speed transaction */
 375 #define T_PID         0x00c00000         /* packet id */
 376 #define T_NAK         0x00100000         /* No ack. */
 377 #define T_STAL        0x00080000         /* Stall received */
 378 #define T_TO          0x00040000         /* time out */
 379 #define T_UN          0x00020000         /* underrun */
 380 
 381 #define DEVICE_T_ERROR    (T_UN | T_TO)
 382 #define HOST_T_ERROR      (T_UN | T_TO | T_NAK | T_STAL)
 383 #define DEVICE_T_BD_MASK  DEVICE_T_ERROR
 384 #define HOST_T_BD_MASK    HOST_T_ERROR
 385 
 386 #define T_PID_SHIFT   6
 387 #define T_PID_DATA0   0x00800000         /* Data 0 toggle */
 388 #define T_PID_DATA1   0x00c00000         /* Data 1 toggle */
 389 
 390 /*
 391  * receive BD's status
 392  */
 393 #define R_E           0x80000000         /* buffer empty */
 394 #define R_W           0x20000000         /* wrap bit */
 395 #define R_I           0x10000000         /* interrupt on reception */
 396 #define R_L           0x08000000         /* last */
 397 #define R_F           0x04000000         /* first */
 398 #define R_PID         0x00c00000         /* packet id */
 399 #define R_NO          0x00100000         /* Rx Non Octet Aligned Packet */
 400 #define R_AB          0x00080000         /* Frame Aborted */
 401 #define R_CR          0x00040000         /* CRC Error */
 402 #define R_OV          0x00020000         /* Overrun */
 403 
 404 #define R_ERROR       (R_NO | R_AB | R_CR | R_OV)
 405 #define R_BD_MASK     R_ERROR
 406 
 407 #define R_PID_DATA0   0x00000000
 408 #define R_PID_DATA1   0x00400000
 409 #define R_PID_SETUP   0x00800000
 410 
 411 #define CPM_USB_STOP_TX 0x2e600000
 412 #define CPM_USB_RESTART_TX 0x2e600000
 413 #define CPM_USB_STOP_TX_OPCODE 0x0a
 414 #define CPM_USB_RESTART_TX_OPCODE 0x0b
 415 #define CPM_USB_EP_SHIFT 5
 416 
 417 #endif  /* __FSL_QE_UDC_H */
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/usb/gadget/udc/fsl_qe_udc.h

INCLUDED FROM

DEFINITIONS
