drivers/usb/phy/phy-fsl-usb.h

/* [<][>][^][v][top][bottom][index][help] */
   1 // SPDX-License-Identifier: GPL-2.0+
   2 /* Copyright (C) 2007,2008 Freescale Semiconductor, Inc. */
   3 
   4 #include <linux/usb/otg-fsm.h>
   5 #include <linux/usb/otg.h>
   6 #include <linux/ioctl.h>
   7 
   8 /* USB Command Register Bit Masks */
   9 #define USB_CMD_RUN_STOP                (0x1<<0)
  10 #define USB_CMD_CTRL_RESET              (0x1<<1)
  11 #define USB_CMD_PERIODIC_SCHEDULE_EN    (0x1<<4)
  12 #define USB_CMD_ASYNC_SCHEDULE_EN       (0x1<<5)
  13 #define USB_CMD_INT_AA_DOORBELL         (0x1<<6)
  14 #define USB_CMD_ASP                     (0x3<<8)
  15 #define USB_CMD_ASYNC_SCH_PARK_EN       (0x1<<11)
  16 #define USB_CMD_SUTW                    (0x1<<13)
  17 #define USB_CMD_ATDTW                   (0x1<<14)
  18 #define USB_CMD_ITC                     (0xFF<<16)
  19 
  20 /* bit 15,3,2 are frame list size */
  21 #define USB_CMD_FRAME_SIZE_1024         (0x0<<15 | 0x0<<2)
  22 #define USB_CMD_FRAME_SIZE_512          (0x0<<15 | 0x1<<2)
  23 #define USB_CMD_FRAME_SIZE_256          (0x0<<15 | 0x2<<2)
  24 #define USB_CMD_FRAME_SIZE_128          (0x0<<15 | 0x3<<2)
  25 #define USB_CMD_FRAME_SIZE_64           (0x1<<15 | 0x0<<2)
  26 #define USB_CMD_FRAME_SIZE_32           (0x1<<15 | 0x1<<2)
  27 #define USB_CMD_FRAME_SIZE_16           (0x1<<15 | 0x2<<2)
  28 #define USB_CMD_FRAME_SIZE_8            (0x1<<15 | 0x3<<2)
  29 
  30 /* bit 9-8 are async schedule park mode count */
  31 #define USB_CMD_ASP_00                  (0x0<<8)
  32 #define USB_CMD_ASP_01                  (0x1<<8)
  33 #define USB_CMD_ASP_10                  (0x2<<8)
  34 #define USB_CMD_ASP_11                  (0x3<<8)
  35 #define USB_CMD_ASP_BIT_POS             (8)
  36 
  37 /* bit 23-16 are interrupt threshold control */
  38 #define USB_CMD_ITC_NO_THRESHOLD        (0x00<<16)
  39 #define USB_CMD_ITC_1_MICRO_FRM         (0x01<<16)
  40 #define USB_CMD_ITC_2_MICRO_FRM         (0x02<<16)
  41 #define USB_CMD_ITC_4_MICRO_FRM         (0x04<<16)
  42 #define USB_CMD_ITC_8_MICRO_FRM         (0x08<<16)
  43 #define USB_CMD_ITC_16_MICRO_FRM        (0x10<<16)
  44 #define USB_CMD_ITC_32_MICRO_FRM        (0x20<<16)
  45 #define USB_CMD_ITC_64_MICRO_FRM        (0x40<<16)
  46 #define USB_CMD_ITC_BIT_POS             (16)
  47 
  48 /* USB Status Register Bit Masks */
  49 #define USB_STS_INT                     (0x1<<0)
  50 #define USB_STS_ERR                     (0x1<<1)
  51 #define USB_STS_PORT_CHANGE             (0x1<<2)
  52 #define USB_STS_FRM_LST_ROLL            (0x1<<3)
  53 #define USB_STS_SYS_ERR                 (0x1<<4)
  54 #define USB_STS_IAA                     (0x1<<5)
  55 #define USB_STS_RESET_RECEIVED          (0x1<<6)
  56 #define USB_STS_SOF                     (0x1<<7)
  57 #define USB_STS_DCSUSPEND               (0x1<<8)
  58 #define USB_STS_HC_HALTED               (0x1<<12)
  59 #define USB_STS_RCL                     (0x1<<13)
  60 #define USB_STS_PERIODIC_SCHEDULE       (0x1<<14)
  61 #define USB_STS_ASYNC_SCHEDULE          (0x1<<15)
  62 
  63 /* USB Interrupt Enable Register Bit Masks */
  64 #define USB_INTR_INT_EN                 (0x1<<0)
  65 #define USB_INTR_ERR_INT_EN             (0x1<<1)
  66 #define USB_INTR_PC_DETECT_EN           (0x1<<2)
  67 #define USB_INTR_FRM_LST_ROLL_EN        (0x1<<3)
  68 #define USB_INTR_SYS_ERR_EN             (0x1<<4)
  69 #define USB_INTR_ASYN_ADV_EN            (0x1<<5)
  70 #define USB_INTR_RESET_EN               (0x1<<6)
  71 #define USB_INTR_SOF_EN                 (0x1<<7)
  72 #define USB_INTR_DEVICE_SUSPEND         (0x1<<8)
  73 
  74 /* Device Address bit masks */
  75 #define USB_DEVICE_ADDRESS_MASK         (0x7F<<25)
  76 #define USB_DEVICE_ADDRESS_BIT_POS      (25)
  77 /* PORTSC  Register Bit Masks,Only one PORT in OTG mode*/
  78 #define PORTSC_CURRENT_CONNECT_STATUS   (0x1<<0)
  79 #define PORTSC_CONNECT_STATUS_CHANGE    (0x1<<1)
  80 #define PORTSC_PORT_ENABLE              (0x1<<2)
  81 #define PORTSC_PORT_EN_DIS_CHANGE       (0x1<<3)
  82 #define PORTSC_OVER_CURRENT_ACT         (0x1<<4)
  83 #define PORTSC_OVER_CUURENT_CHG         (0x1<<5)
  84 #define PORTSC_PORT_FORCE_RESUME        (0x1<<6)
  85 #define PORTSC_PORT_SUSPEND             (0x1<<7)
  86 #define PORTSC_PORT_RESET               (0x1<<8)
  87 #define PORTSC_LINE_STATUS_BITS         (0x3<<10)
  88 #define PORTSC_PORT_POWER               (0x1<<12)
  89 #define PORTSC_PORT_INDICTOR_CTRL       (0x3<<14)
  90 #define PORTSC_PORT_TEST_CTRL           (0xF<<16)
  91 #define PORTSC_WAKE_ON_CONNECT_EN       (0x1<<20)
  92 #define PORTSC_WAKE_ON_CONNECT_DIS      (0x1<<21)
  93 #define PORTSC_WAKE_ON_OVER_CURRENT     (0x1<<22)
  94 #define PORTSC_PHY_LOW_POWER_SPD        (0x1<<23)
  95 #define PORTSC_PORT_FORCE_FULL_SPEED    (0x1<<24)
  96 #define PORTSC_PORT_SPEED_MASK          (0x3<<26)
  97 #define PORTSC_TRANSCEIVER_WIDTH        (0x1<<28)
  98 #define PORTSC_PHY_TYPE_SEL             (0x3<<30)
  99 /* bit 11-10 are line status */
 100 #define PORTSC_LINE_STATUS_SE0          (0x0<<10)
 101 #define PORTSC_LINE_STATUS_JSTATE       (0x1<<10)
 102 #define PORTSC_LINE_STATUS_KSTATE       (0x2<<10)
 103 #define PORTSC_LINE_STATUS_UNDEF        (0x3<<10)
 104 #define PORTSC_LINE_STATUS_BIT_POS      (10)
 105 
 106 /* bit 15-14 are port indicator control */
 107 #define PORTSC_PIC_OFF                  (0x0<<14)
 108 #define PORTSC_PIC_AMBER                (0x1<<14)
 109 #define PORTSC_PIC_GREEN                (0x2<<14)
 110 #define PORTSC_PIC_UNDEF                (0x3<<14)
 111 #define PORTSC_PIC_BIT_POS              (14)
 112 
 113 /* bit 19-16 are port test control */
 114 #define PORTSC_PTC_DISABLE              (0x0<<16)
 115 #define PORTSC_PTC_JSTATE               (0x1<<16)
 116 #define PORTSC_PTC_KSTATE               (0x2<<16)
 117 #define PORTSC_PTC_SEQNAK               (0x3<<16)
 118 #define PORTSC_PTC_PACKET               (0x4<<16)
 119 #define PORTSC_PTC_FORCE_EN             (0x5<<16)
 120 #define PORTSC_PTC_BIT_POS              (16)
 121 
 122 /* bit 27-26 are port speed */
 123 #define PORTSC_PORT_SPEED_FULL          (0x0<<26)
 124 #define PORTSC_PORT_SPEED_LOW           (0x1<<26)
 125 #define PORTSC_PORT_SPEED_HIGH          (0x2<<26)
 126 #define PORTSC_PORT_SPEED_UNDEF         (0x3<<26)
 127 #define PORTSC_SPEED_BIT_POS            (26)
 128 
 129 /* bit 28 is parallel transceiver width for UTMI interface */
 130 #define PORTSC_PTW                      (0x1<<28)
 131 #define PORTSC_PTW_8BIT                 (0x0<<28)
 132 #define PORTSC_PTW_16BIT                (0x1<<28)
 133 
 134 /* bit 31-30 are port transceiver select */
 135 #define PORTSC_PTS_UTMI                 (0x0<<30)
 136 #define PORTSC_PTS_ULPI                 (0x2<<30)
 137 #define PORTSC_PTS_FSLS_SERIAL          (0x3<<30)
 138 #define PORTSC_PTS_BIT_POS              (30)
 139 
 140 #define PORTSC_W1C_BITS                 \
 141         (PORTSC_CONNECT_STATUS_CHANGE | \
 142          PORTSC_PORT_EN_DIS_CHANGE    | \
 143          PORTSC_OVER_CUURENT_CHG)
 144 
 145 /* OTG Status Control Register Bit Masks */
 146 #define OTGSC_CTRL_VBUS_DISCHARGE       (0x1<<0)
 147 #define OTGSC_CTRL_VBUS_CHARGE          (0x1<<1)
 148 #define OTGSC_CTRL_OTG_TERMINATION      (0x1<<3)
 149 #define OTGSC_CTRL_DATA_PULSING         (0x1<<4)
 150 #define OTGSC_CTRL_ID_PULL_EN           (0x1<<5)
 151 #define OTGSC_HA_DATA_PULSE             (0x1<<6)
 152 #define OTGSC_HA_BA                     (0x1<<7)
 153 #define OTGSC_STS_USB_ID                (0x1<<8)
 154 #define OTGSC_STS_A_VBUS_VALID          (0x1<<9)
 155 #define OTGSC_STS_A_SESSION_VALID       (0x1<<10)
 156 #define OTGSC_STS_B_SESSION_VALID       (0x1<<11)
 157 #define OTGSC_STS_B_SESSION_END         (0x1<<12)
 158 #define OTGSC_STS_1MS_TOGGLE            (0x1<<13)
 159 #define OTGSC_STS_DATA_PULSING          (0x1<<14)
 160 #define OTGSC_INTSTS_USB_ID             (0x1<<16)
 161 #define OTGSC_INTSTS_A_VBUS_VALID       (0x1<<17)
 162 #define OTGSC_INTSTS_A_SESSION_VALID    (0x1<<18)
 163 #define OTGSC_INTSTS_B_SESSION_VALID    (0x1<<19)
 164 #define OTGSC_INTSTS_B_SESSION_END      (0x1<<20)
 165 #define OTGSC_INTSTS_1MS                (0x1<<21)
 166 #define OTGSC_INTSTS_DATA_PULSING       (0x1<<22)
 167 #define OTGSC_INTR_USB_ID_EN            (0x1<<24)
 168 #define OTGSC_INTR_A_VBUS_VALID_EN      (0x1<<25)
 169 #define OTGSC_INTR_A_SESSION_VALID_EN   (0x1<<26)
 170 #define OTGSC_INTR_B_SESSION_VALID_EN   (0x1<<27)
 171 #define OTGSC_INTR_B_SESSION_END_EN     (0x1<<28)
 172 #define OTGSC_INTR_1MS_TIMER_EN         (0x1<<29)
 173 #define OTGSC_INTR_DATA_PULSING_EN      (0x1<<30)
 174 #define OTGSC_INTSTS_MASK               (0x00ff0000)
 175 
 176 /* USB MODE Register Bit Masks */
 177 #define  USB_MODE_CTRL_MODE_IDLE        (0x0<<0)
 178 #define  USB_MODE_CTRL_MODE_DEVICE      (0x2<<0)
 179 #define  USB_MODE_CTRL_MODE_HOST        (0x3<<0)
 180 #define  USB_MODE_CTRL_MODE_RSV         (0x1<<0)
 181 #define  USB_MODE_SETUP_LOCK_OFF        (0x1<<3)
 182 #define  USB_MODE_STREAM_DISABLE        (0x1<<4)
 183 #define  USB_MODE_ES                    (0x1<<2) /* Endian Select */
 184 
 185 /* control Register Bit Masks */
 186 #define  USB_CTRL_IOENB                 (0x1<<2)
 187 #define  USB_CTRL_ULPI_INT0EN           (0x1<<0)
 188 
 189 /* BCSR5 */
 190 #define BCSR5_INT_USB                   (0x02)
 191 
 192 /* USB module clk cfg */
 193 #define SCCR_OFFS                       (0xA08)
 194 #define SCCR_USB_CLK_DISABLE            (0x00000000)    /* USB clk disable */
 195 #define SCCR_USB_MPHCM_11               (0x00c00000)
 196 #define SCCR_USB_MPHCM_01               (0x00400000)
 197 #define SCCR_USB_MPHCM_10               (0x00800000)
 198 #define SCCR_USB_DRCM_11                (0x00300000)
 199 #define SCCR_USB_DRCM_01                (0x00100000)
 200 #define SCCR_USB_DRCM_10                (0x00200000)
 201 
 202 #define SICRL_OFFS                      (0x114)
 203 #define SICRL_USB0                      (0x40000000)
 204 #define SICRL_USB1                      (0x20000000)
 205 
 206 #define SICRH_OFFS                      (0x118)
 207 #define SICRH_USB_UTMI                  (0x00020000)
 208 
 209 /* OTG interrupt enable bit masks */
 210 #define  OTGSC_INTERRUPT_ENABLE_BITS_MASK  \
 211         (OTGSC_INTR_USB_ID_EN            | \
 212         OTGSC_INTR_1MS_TIMER_EN          | \
 213         OTGSC_INTR_A_VBUS_VALID_EN       | \
 214         OTGSC_INTR_A_SESSION_VALID_EN    | \
 215         OTGSC_INTR_B_SESSION_VALID_EN    | \
 216         OTGSC_INTR_B_SESSION_END_EN      | \
 217         OTGSC_INTR_DATA_PULSING_EN)
 218 
 219 /* OTG interrupt status bit masks */
 220 #define  OTGSC_INTERRUPT_STATUS_BITS_MASK  \
 221         (OTGSC_INTSTS_USB_ID          |    \
 222         OTGSC_INTR_1MS_TIMER_EN       |    \
 223         OTGSC_INTSTS_A_VBUS_VALID     |    \
 224         OTGSC_INTSTS_A_SESSION_VALID  |    \
 225         OTGSC_INTSTS_B_SESSION_VALID  |    \
 226         OTGSC_INTSTS_B_SESSION_END    |    \
 227         OTGSC_INTSTS_DATA_PULSING)
 228 
 229 /*
 230  *  A-DEVICE timing  constants
 231  */
 232 
 233 /* Wait for VBUS Rise  */
 234 #define TA_WAIT_VRISE   (100)   /* a_wait_vrise 100 ms, section: 6.6.5.1 */
 235 
 236 /* Wait for B-Connect */
 237 #define TA_WAIT_BCON    (10000)  /* a_wait_bcon > 1 sec, section: 6.6.5.2
 238                                   * This is only used to get out of
 239                                   * OTG_STATE_A_WAIT_BCON state if there was
 240                                   * no connection for these many milliseconds
 241                                   */
 242 
 243 /* A-Idle to B-Disconnect */
 244 /* It is necessary for this timer to be more than 750 ms because of a bug in OPT
 245  * test 5.4 in which B OPT disconnects after 750 ms instead of 75ms as stated
 246  * in the test description
 247  */
 248 #define TA_AIDL_BDIS    (5000)  /* a_suspend minimum 200 ms, section: 6.6.5.3 */
 249 
 250 /* B-Idle to A-Disconnect */
 251 #define TA_BIDL_ADIS    (12)    /* 3 to 200 ms */
 252 
 253 /* B-device timing constants */
 254 
 255 
 256 /* Data-Line Pulse Time*/
 257 #define TB_DATA_PLS     (10)    /* b_srp_init,continue 5~10ms, section:5.3.3 */
 258 #define TB_DATA_PLS_MIN (5)     /* minimum 5 ms */
 259 #define TB_DATA_PLS_MAX (10)    /* maximum 10 ms */
 260 
 261 /* SRP Initiate Time  */
 262 #define TB_SRP_INIT     (100)   /* b_srp_init,maximum 100 ms, section:5.3.8 */
 263 
 264 /* SRP Fail Time  */
 265 #define TB_SRP_FAIL     (7000)  /* b_srp_init,Fail time 5~30s, section:6.8.2.2*/
 266 
 267 /* SRP result wait time */
 268 #define TB_SRP_WAIT     (60)
 269 
 270 /* VBus time */
 271 #define TB_VBUS_PLS     (30)    /* time to keep vbus pulsing asserted */
 272 
 273 /* Discharge time */
 274 /* This time should be less than 10ms. It varies from system to system. */
 275 #define TB_VBUS_DSCHRG  (8)
 276 
 277 /* A-SE0 to B-Reset  */
 278 #define TB_ASE0_BRST    (20)    /* b_wait_acon, mini 3.125 ms,section:6.8.2.4 */
 279 
 280 /* A bus suspend timer before we can switch to b_wait_aconn */
 281 #define TB_A_SUSPEND    (7)
 282 #define TB_BUS_RESUME   (12)
 283 
 284 /* SE0 Time Before SRP */
 285 #define TB_SE0_SRP      (2)     /* b_idle,minimum 2 ms, section:5.3.2 */
 286 
 287 #define SET_OTG_STATE(phy, newstate)    ((phy)->otg->state = newstate)
 288 
 289 struct usb_dr_mmap {
 290         /* Capability register */
 291         u8 res1[256];
 292         u16 caplength;          /* Capability Register Length */
 293         u16 hciversion;         /* Host Controller Interface Version */
 294         u32 hcsparams;          /* Host Controller Structual Parameters */
 295         u32 hccparams;          /* Host Controller Capability Parameters */
 296         u8 res2[20];
 297         u32 dciversion;         /* Device Controller Interface Version */
 298         u32 dccparams;          /* Device Controller Capability Parameters */
 299         u8 res3[24];
 300         /* Operation register */
 301         u32 usbcmd;             /* USB Command Register */
 302         u32 usbsts;             /* USB Status Register */
 303         u32 usbintr;            /* USB Interrupt Enable Register */
 304         u32 frindex;            /* Frame Index Register */
 305         u8 res4[4];
 306         u32 deviceaddr;         /* Device Address */
 307         u32 endpointlistaddr;   /* Endpoint List Address Register */
 308         u8 res5[4];
 309         u32 burstsize;          /* Master Interface Data Burst Size Register */
 310         u32 txttfilltuning;     /* Transmit FIFO Tuning Controls Register */
 311         u8 res6[8];
 312         u32 ulpiview;           /* ULPI register access */
 313         u8 res7[12];
 314         u32 configflag;         /* Configure Flag Register */
 315         u32 portsc;             /* Port 1 Status and Control Register */
 316         u8 res8[28];
 317         u32 otgsc;              /* On-The-Go Status and Control */
 318         u32 usbmode;            /* USB Mode Register */
 319         u32 endptsetupstat;     /* Endpoint Setup Status Register */
 320         u32 endpointprime;      /* Endpoint Initialization Register */
 321         u32 endptflush;         /* Endpoint Flush Register */
 322         u32 endptstatus;        /* Endpoint Status Register */
 323         u32 endptcomplete;      /* Endpoint Complete Register */
 324         u32 endptctrl[6];       /* Endpoint Control Registers */
 325         u8 res9[552];
 326         u32 snoop1;
 327         u32 snoop2;
 328         u32 age_cnt_thresh;     /* Age Count Threshold Register */
 329         u32 pri_ctrl;           /* Priority Control Register */
 330         u32 si_ctrl;            /* System Interface Control Register */
 331         u8 res10[236];
 332         u32 control;            /* General Purpose Control Register */
 333 };
 334 
 335 struct fsl_otg_timer {
 336         unsigned long expires;  /* Number of count increase to timeout */
 337         unsigned long count;    /* Tick counter */
 338         void (*function)(unsigned long);        /* Timeout function */
 339         unsigned long data;     /* Data passed to function */
 340         struct list_head list;
 341 };
 342 
 343 inline struct fsl_otg_timer *otg_timer_initializer
 344 (void (*function)(unsigned long), unsigned long expires, unsigned long data)
 345 {
 346         struct fsl_otg_timer *timer;
 347 
 348         timer = kmalloc(sizeof(struct fsl_otg_timer), GFP_KERNEL);
 349         if (!timer)
 350                 return NULL;
 351         timer->function = function;
 352         timer->expires = expires;
 353         timer->data = data;
 354         return timer;
 355 }
 356 
 357 struct fsl_otg {
 358         struct usb_phy phy;
 359         struct otg_fsm fsm;
 360         struct usb_dr_mmap *dr_mem_map;
 361         struct delayed_work otg_event;
 362 
 363         /* used for usb host */
 364         struct work_struct work_wq;
 365         u8      host_working;
 366 
 367         int irq;
 368 };
 369 
 370 struct fsl_otg_config {
 371         u8 otg_port;
 372 };
 373 
 374 /* For SRP and HNP handle */
 375 #define FSL_OTG_MAJOR           240
 376 #define FSL_OTG_NAME            "fsl-usb2-otg"
 377 /* Command to OTG driver ioctl */
 378 #define OTG_IOCTL_MAGIC         FSL_OTG_MAJOR
 379 /* if otg work as host, it should return 1, otherwise return 0 */
 380 #define GET_OTG_STATUS          _IOR(OTG_IOCTL_MAGIC, 1, int)
 381 #define SET_A_SUSPEND_REQ       _IOW(OTG_IOCTL_MAGIC, 2, int)
 382 #define SET_A_BUS_DROP          _IOW(OTG_IOCTL_MAGIC, 3, int)
 383 #define SET_A_BUS_REQ           _IOW(OTG_IOCTL_MAGIC, 4, int)
 384 #define SET_B_BUS_REQ           _IOW(OTG_IOCTL_MAGIC, 5, int)
 385 #define GET_A_SUSPEND_REQ       _IOR(OTG_IOCTL_MAGIC, 6, int)
 386 #define GET_A_BUS_DROP          _IOR(OTG_IOCTL_MAGIC, 7, int)
 387 #define GET_A_BUS_REQ           _IOR(OTG_IOCTL_MAGIC, 8, int)
 388 #define GET_B_BUS_REQ           _IOR(OTG_IOCTL_MAGIC, 9, int)
 389 
 390 void fsl_otg_add_timer(struct otg_fsm *fsm, void *timer);
 391 void fsl_otg_del_timer(struct otg_fsm *fsm, void *timer);
 392 void fsl_otg_pulse_vbus(void);
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/usb/phy/phy-fsl-usb.h

INCLUDED FROM
